Skip to main content
ACS Omega logoLink to ACS Omega
. 2023 Dec 14;8(51):48590–48612. doi: 10.1021/acsomega.3c05397

Research and Development of Hydrogen-Fueled Internal Combustion Engines in China

Lijun Wang †,‡,§, Xiangyang Li ‡, Chen Hong †,§, Ping Guo †,§, Shuman Guo †,§, Zhenzhong Yang †,§,*
PMCID: PMC10753572  PMID: 38162766

Abstract

graphic file with name ao3c05397_0021.jpg

Energy shortages and environmental problems have brought many challenges to China’s development. In the field of transport, hydrogen energy has become a new type of energy that people pay attention to due to its easy production and nonpolluting generation. The use of hydrogen as a fuel in internal combustion engines can be a good way to make a low-cost and clean conversion of the current internal combustion engine, thus realizing the application of hydrogen energy in vehicles. In this study, hydrogen-fueled internal combustion engines (HICEs) are the focus. A review and analysis of the topical issues encountered in the developmental research of HICE is presented, such as the optimization control method of the combustion process, mechanism and suppression method of abnormal combustion (preignition, backfire, knock, and high pressure rise rate in early stages of combustion), influence regularity of hydrogen injection parameters and hydrogen injection modes on the formation and combustion performance of H2–air mixture, emissions and control of NOx, formation of H2–air mixture, and combustion cycle variation, among others. Multiyear studies in the hydrogen-fueled engines clearly show that abnormal combustion, as preignition, backfire, and the blockage of intake pipe, is likely to occur at high load, and the H2 injection parameters and the injection modes possess a prominent effect on the engine’s performance and the blockage of the intake pipe, which has an important impact on the preignition and backfire, and the optimal control of the combustion process is a valuable method for resolving the contradictions among inhibiting abnormal combustion, the blockage of the intake pipe, and enhancing hydrogen-fueled engine power.

1. Introduction

Energy and the environment are growing concerns today, and energy resources are an important foundation for social progress and economic development. China became a net importer of oil for the first time in 1993, a net importer of natural gas in 2006, and a net importer of coal in 2009. Energy shortage has affected China’s economic development. While fossil fuels have driven China’s rapid technological and economic development, they have also brought about a series of problems such as environmental degradation and the greenhouse effect. Under the double pressure of saving energy and environmental protection, China’s automotive industry is facing a huge challenge, and it is imperative to find a new clean energy source. Hydrogen energy has become one of the ideal energy alternatives in the transport sector due to the nonpolluting nature of its generation and the simplicity of its production method. There are two main ways to use hydrogen energy as a power source: one is the hydrogen fuel cell, and the other is the hydrogen internal combustion engine.1 However, the fact is that there is currently a large market for internal combustion engines, and the conversion to hydrogen fuel cells would result in a much greater economic loss. Therefore, the hydrogen combustion engine, which can be operated by simply modifying existing combustion engine vehicles, is an ideal solution at this stage and is expected to be an important part of the future energy system of a hydrogen society.2

Hydrogen has many excellent properties when burned, such as fast combustion, flame propagation about 8 times faster than that of petrol, and high thermal efficiency. The calorific value of hydrogen fuel is only lower than that of nuclear fuel. The low calorific value is 2.7 times that of gasoline, and the diffusion rate of H2 in premixed combustion is better and more fully mixed.3 The autoignition temperature of H2 is higher than that of natural gas or gasoline, which is conducive to higher compression ratios and a higher thermal efficiency of combustion. It is suitable for ignition, but not for compression ignition.4 The ignition limit of hydrogen is wider, which is favorable to dilute combustion. The normal ignition energy of H2 is very low. When used as a substitute fuel for internal combustion engines, it is not easy to misfire, but is prone to abnormal combustion such as preignition and backfire. The product of combustion of hydrogen is water. Its exhaust pollutants also contain only nitrogen oxides, which are easily resolved. Therefore, hydrogen would be very suitable as a fuel for internal combustion engines. However, there are still many problems that need to be solved when replacing the fuel of internal combustion engine with hydrogen, such as premature combustion, backfire, and other abnormal combustion phenomena due to the calorific value of hydrogen and the combustion speed.5 When hydrogen is used as the fuel of the engine, corresponding improvements to the internal combustion engine are necessary, such as structural improvements and the use of optimal control methods, etc. A large number of scholars have researched these issues in the past decades and produced corresponding research results.

In this study, the current status of hydrogen energy in the field of automotive internal combustion engines (ICEs) is analyzed, starting with an introduction to the fundamentals of HICEs, analyzing the theoretical foundations of HICEs as well as the development of the main research methodologies, and the forms of HICEs that have a great impact on their application, so that the main forms of HICEs as well as their strengths and weaknesses are also described in section 2.2. Since the progress of hydrogen doped internal combustion engines in China in the last two decades has already been summarized,6 in this section, pure hydrogen internal combustion engines will be analyzed in a more focused manner. In section 3, given that China is one of the major forces in HICEs research, Chinese research topics on HICEs are analyzed in this section, as are more detailed topics such as how to solve the anomalous combustion encountered in the development of HICEs, the effect of different parameters on HICEs, the emission characteristics of HICEs, and their optimal control. In each theme, representative research results are discussed, and future trends are outlooked. In the final part, the developments of the hydrogen internal combustion engine in China in the past 30 years are summarized, and the related prospects are presented.

2. Fundamentals of the HICEs

2.1. Theoretical Foundations and Research Methods of HICEs

The earliest current record of a hydrogen internal combustion engine is the gas engine mentioned in the study by Rev. W. Cecil.7 The more systematic research on hydrogen internal combustion engines (HICEs) comes from the last century and has reached a peak in this century. The operation of a hydrogen internal combustion engine is a multiphysical field coupling process, and, similar to a conventional internal combustion engine, the operation of a hydrogen internal combustion engine is also in accordance with the corresponding theoretical cyclic process; therefore, theoretically, the conventional internal combustion engine can be well adapted to the application of hydrogen in the internal combustion engine by making corresponding improvements to the combustion characteristics of the hydrogen fuel. It can be seen that the main theories in the research of hydrogen internal combustion engine also come from the development of the traditional internal combustion engine, as the combustion model is an important part of the theoretical foundation of the internal combustion engine and also plays an important role in the hydrogen internal combustion engine; for example, the Single-Zone Model is a commonly used model in research of the internal combustion engine, as it is the assumption of uniform distribution of the work mass in the cylinder, and the development of thermodynamic parameter is equal everywhere in the thermodynamic model. The Single-Zone Model has been adapted and extended in some studies to investigate the applicability of the Single-Zone Model for internal combustion engines fueled by hydrogen, and to evaluate the performance of different types of hydrogen internal combustion engines.8,9

However, in the research of the hydrogen internal combustion engine, the Single-Zone Model has difficulty taking into account the comprehensive parameters and is too ideal, so the Quasi-dimensional Combustion Model has gradually appeared, which takes into account the physical processes of combustion mass diffusion and flame propagation in the thermodynamic model and carries out the construction of the mathematical model by dividing the combustion chamber into more than two zones. By dividing the combustion chamber into more than two compartments, the mathematical model can be constructed, through which the model can be closer to the actual situation; therefore, in the research related to the hydrogen internal combustion engine, the Quasi-dimensional Combustion Model is also one of the commonly used basic models of fuel theory. Through the development of the flame, the products of combustion, and the consideration of the characteristics of the flow field, etc., the calculation accuracy of the Quasi-dimensional Combustion Model can be improved by flame development, combustion products, and consideration of flow field characteristics.10,11 However, the Quasi-dimensional Combustion Model is difficult to generalize due to its specificity and consideration of subprocesses.

With the development of computers, a large number of multidimensional models have been gradually developed, and the three-dimensional model of the internal combustion engine is constructed by simulating the bases of thermodynamics, fluid dynamics, heat and mass transfer, and chemical reaction kinetics, etc. It has become a trend to carry out the simulation of the internal combustion engine in the field of numerical simulation of all working conditions, and this kind of method is more persuasive theoretically as a development of numerical computation. However, the construction of a perfect multidimensional model is not an easy task, and it requires the joint efforts of specialists in the field of internal combustion engines, specialists in the field of mathematics, and specialists in programming, as well as the development of computers. Of course, it is undeniable that such methods are already being applied with good results. Through numerical simulation, the various processes in a hydrogen combustion engine can be easily seen, such as the distribution of the temperature field in the cylinder, the distribution of the concentration of the combustion mass, and the generation pattern of the products.12,13 Meanwhile, in the foreseeable future, it will be a trend to build digital twins based on such methods to achieve the purpose of virtual testing, real-time monitoring, health operation, and maintenance of complex equipment. At present, in the field of the internal combustion engine, scholars have already made attempts to build digital twins on internal combustion engine sensors, internal combustion engine power plants, and other objects.14,15 However, it has not yet been reported in the field of HICEs.

2.2. Structure Forms of HICEs

According to how hydrogen is used in the internal combustion engine, HICEs can be divided into a pure hydrogen internal combustion engine and a hydrogen-blended internal combustion engine. In view of the nature of hydrogen, the hydrogen internal combustion engine is generally in the way of spark ignition (SI); through the hydrogen and gasoline, alcohol or other fuels can be doped to a certain extent to improve the performance of the original internal combustion engine and emissions, or through the use of compression ignition (CI) of fuels as a carrier and mix with the hydrogen and then through the CI method of ignition, the pure hydrogen engine due to the nature of hydrogen, so that the majority of the engine is the SI engine.16 However, some scholars argued that premixed charge limits the engine efficiency, power density, and safety, while diesel injections give rise to CO2 and particulate emissions. Therefore, they have attempted to design a pure hydrogen compression-ignition engine.17 The structure of HICEs is basically the same as that of a conventional internal combustion engine, with the difference that a hydrogen internal combustion engine has a separate hydrogen supply system that includes a series of auxiliary components such as hydrogen storage, hydrogen delivery, and hydrogen injection. In Figure 1,18 the structure of a typical hydrogen internal combustion engine test stand is shown. Although this is a single-cylinder piston engine, it can be adapted to other types of engines by replacing the accessories on the stand and making minor structural changes, such as different hydrogen injection positions, different engine types, different fuel types,19 different ignition positions and modes,20,21 etc. According to the structure of HICEs, they can be divided into spark ignition (SI) engines and compression ignition (CI) engines, and, according to the form of engine movement, hydrogen internal combustion engines for automobiles can be divided into four-stroke engines, two-stroke engines, and rotary engines, etc. As a matter of fact, Ford, BMW, Mazda, Volkswagen, Lexus, etc., have already had their hydrogen internal combustion engine automobiles tested.22

Figure 1.

Figure 1

Structural arrangement of a typical hydrogen internal combustion engine and accessories from the literature.18 Reprinted with permission from ref (18). Copyright 2023 MDPI (Basel, Switzerland).

3. Current Status of Research on Different Topics of HICEs in China

According to data on Web of Science, as of September 2023, there are 3391 papers related to hydrogen internal combustion engines, and the trend of related publications is shown in Figure 2. It can be seen that the research intensity of this field is increasing, in which the research from China accounts for 28%, which has an important position in the field. The distribution of research in various countries is shown in Figure 3, and China has the largest automobile market in the world, so a review of the research on hydrogen-fueled internal combustion engines in China is also of great significance for the development of the field and the assessment of the overall development of the status of the hydrogen combustion engines by other scholars.

Figure 2.

Figure 2

Trends in the number of articles on HICEs.

Figure 3.

Figure 3

National/regional distribution of researchers in HICEs.

The research on hydrogen as the alternative fuel for vehicles in China originated from the end of the last century, but the research institutions were extremely rare, as in-depth research was not enough either. Chinese researchers have made unremitting efforts to study H2 as the fuel for vehicle internal combustion engines since the 21st century and have made considerable progress.

3.1. A Study Related to the Structural Form of Different HICEs

As mentioned in section 2, there is no single form of a hydrogen combustion engine, and scholars are always looking for the most suitable form or exploring ways to study what works best in a particular form. The same is true for Chinese research.

When hydrogen is used as the only fuel, its ignition timing has a great influence on the power characteristics of the hydrogen internal combustion engine; improper ignition timing will bring backfire phenomenon and even lead to engine misfire in serious cases. In the study of Li et al., it was found that the interval of injection timing and ignition timing should be controlled less than 0.05 ms for ensuring the engine can operate normally.23 Because of the nature of hydrogen, the mixing ratio with air, the method of hydrogen injection, and the cyclic behavior under different operating conditions are also important.24,25 In addition, when hydrogen is used as a stand-alone fuel, NOx control is still an issue that needs to be addressed despite the absence of carbon compounds in the emissions.26 The control of hydrogen embrittlement is also limiting the development of pure hydrogen engines. Therefore, while efforts are now being made to improve materials, much research is also focusing on the application of hydrogen doping of different fuels in internal combustion engines, where the performance of most engines will be improved by doping hydrogen in different proportions.6 The HICEs constructed by some Chinese companies are shown in Figure 4, and the basic parameters of the achieved hydrogen internal combustion engine tests are shown in Table 1.

Figure 4.

Figure 4

HICEs from Chinese companies. (a) The first HICE in China. Photograph courtesy of Yuanbin Xu. Copyright 2007 (free domain). (b) Hydrogen combustion engine concept sports cars of Changan. (c) HICE from FAW Hong Qi. (d) A small aircraft equipped with HICE. (e) A HICE based on the Magic Core 1.5T engine. (f) A 2.0 L HICE based on the EN platform. (g) A hydrogen-ammonia engine based on the DDi13 engine. (h) A direct-injection HICE from Shanghai New Power Automotive Technology. (i) A direct-injection supercharged HICE from Geely Power Research Institute. (j) A heavy-duty commercial vehicle cylinder direct-injection HICE from FAW Jiefang. (k) YCK16 HICE. (l) X15H HICE. (m) B6.7H HICE. (n) WP15 HICE. (o) A commercially available HICE heavy truck equipped with WP15.

Table 1. Main HICE Products from Chinese Enterprises.

corporations release time engines fuels announced performance parameters thermal efficiency
Changan Automobile 2007 PFI HICE 2.0 L H2    
FAW Hong Qi 2021 20TD HICE H2 or hydrogen gasoline blend   42%
BAIC 2021 Mohe 1.5T HICE H2 80 kW/170 N m more than 43%
Great Wall Motor 2021 based on EN platform 2.0 L HICE H2 maximum power 120 kW, peak torque 230 N m 42%
Dongfeng Motor 2022 DDi13 13 L HICE hydrogen–ammonia dual fuel 338 kW/ 2200 N m more than 45.04%
Shanghai New Power 2022 12.8 L GDI H2 480 PS 44%
Geely Power 2023 2.0 L direct injection supercharged HICE H2 maximum power 110 kW; maximum torque 230 N m 46.11%
Faw Jiefang 2022 13 L cylinder direct injection HICE H2 or hydrogen–ammonia dual fuel more than 500 PS more than 55% (indicative thermal efficiency)
Cummins 2022 X15H H2 (easy fuel change) 395 kW /2600 N m 44%
  2022 B6.7H H2 (easy fuel change) 216 kW /1200 N m  
Guangxi Yuchai Power 2021 YCK05N H2   42%
  2022 YCK16H 15.93 L H2 or hydrogen–ammonia dual fuel 560 PS  
Weichai Power 2022 WP15 15 L HICE H2 390 kW/ 2500 N m 41.8%

As early as 2007, Changan Automobile Group Co., Ltd. developed China’s first hydrogen internal combustion engine (Figure 4a) in cooperation with the Beijing Institute of Technology.27 As of 2013, cars powered by this combustion engine have been running steadily for more than 10 000 km, they have released several hydrogen combustion engine concept sports cars (Figure 4b), and the second generation of the hydrogen combustion engine has already been successfully ignited in 2023. FAW Hong Qi Group unveiled their first hydrogen combustion engine in 2021 (Figure 4c), developed a 20TD hydrogen–gasoline hybrid combustion engine in 2023, and in addition their hydrogen combustion engine was tested on a small aircraft (Figure 4d). The BAIC GROUP, in conjunction with the Beijing University of Technology, has further optimized a HICE (Figure 4e) based on the Magic Core 1.5T engine, which uses key technologies such as nozzles and rails adapted to hydrogen fuel, a hydrogen-specific turbocharger, hydrogen-specific oil, and wear-resistant and hydrogen-resistant valves and seats, which are more than 40%. According to the Great Wall Motor Company, they have developed a 2.0 L hydrogen internal combustion engine (Figure 4f) based on the EN platform, in which cold spark plugs and plating to prevent hydrogen embrittlement have been used, ultimately guaranteeing a combined engine thermal efficiency of 42%. In 2022, the Dongfeng Motor Corporation, in conjunction with a number of Chinese institutions, released two hydrogen internal combustion engines. The hydrogen engine has a power of 80 kW/170 N m, with a thermal efficiency exceeding 45.04%, more than 70% of the efficiency zone is greater than 40%, and there is also a hydrogen–ammonia engine that is based on the 13 L DDi13 engine for retrofitting. The rated power is 338 kW and the maximum torque is 2200 N m, and key technologies to combat hydrogen embrittlement, hydrogen safety monitoring, and other technologies have also been incorporated (Figure 4g). The Shanghai New Power Automotive Technology Co., Ltd., a subsidiary of the SAIC Group, has developed a direct-injection hydrogen internal combustion engine (Figure 4h) designed for a maximum horsepower of 480 PS and a high thermal efficiency of 44%. Geely Power Research Institute announced that after two rounds of exploration and development, it has successfully raised the thermal efficiency of its self-developed 2.0 L direct-injection supercharged hydrogen internal combustion engine (Figure 4i) to 46.11%t, which has reached an industry-leading level. In 2022, China’s first heavy-duty commercial vehicle cylinder direct-injection hydrogen engine, independently developed by the Faw Jiefang Group, was successfully ignited and operated stably (Figure 4j). Guangxi Yuchai Power Co., Ltd. has developed two hydrogen internal combustion engines, including the YCK16 (Figure 4k), currently the largest hydrogen internal combustion engine in China. Cummins has already produced hydrogen internal combustion engines of 15, 10, and 6.7 L displacements, and they are working on building a multifuel engine platform with rapid iterative design through modularization, which in a way enables rapid replacement of internal combustion engines with different fuels by replacing the cylinder head. The X15H (Figure 4l) has accumulated more than 1000+ hours of test time and has brought the thermal efficiency (44%), torque (2600 N m), average effective pressure (22 bar), and other data to achieve China’s more leading level, and its design of the B6.7H (Figure 4m) also successfully ignited. Weichai Power unveiled their WP15 hydrogen combustion engine (Figure 4n) at the Hannover Commercial Vehicle Show, which features flexible hydrogen injection, efficient thin combustion, intelligent ignition start, and Weichai ECU control. This combustion engine has now been installed in China’s first commercially available HICE heavy truck (Figure 4o).

In academia, research on different forms of hydrogen internal combustion engines is more detailed; some scholars have carried out research on other aspects of reciprocating piston hydrogen-fueled engines, such as idle performance, energy distribution, and turbocharged hydrogen-fueled engines. There have also been some scholars who have explored other nonreciprocating piston hydrogen-fueled engines, such as hydrogen-fueled rotary engines, free-piston hydrogen-fueled engines, and hydrogen-fueled scramjet engines. The following is a brief description of this research.

3.1.1. Other Research on Reciprocating Piston Hydrogen-Fueled Engines

Ma et al.28 explored the performance of the hydrogen-fueled engine using turbocharging technology at idling conditions. Results had demonstrated that the decrease indicated thermal efficiency, while the raised maximum cylinder pressure and the increased NOx emissions could be obtained with the increase of Φ. They also found that when Φ remained constant, both NOx emissions and maximum cylinder pressure increased with the increase of θig. He et al.29 employed the same equipment and further studied idle characteristics of the engine. Results from the above-mentioned study reported that the increased θig at MBT point, the raised indicated thermal efficiency, and the decreased NOx emissions could be obtained after increasing λ. They also pointed out that when λ remained constant, NOx emissions increased as θig increased.

For a 2.0 L HICE, Zhao et al.30 studied the ignition energy by the experiment, discussed the influence of ignition energy on power, and then analyzed the correlation of minimum ignition energy with equivalent concentration, speed, and load. Results from experiments revealed that the influence of ignition energy on hydrogen-fueled internal combustion engine power was slight. The minimum ignition energy decreased as the speed increased, and first increased and then decreased as the load increased. When the parameter Φ was smaller than the value 1, the minimum ignition energy decreased with the increase of equivalent concentration. In addition, Luo and Sun31 made experiments to explore the distribution of energy of a 2.3 L turbocharged HICE. Results had shown that the exergy of the engine was raised with the increase of speed and load. Both power output and economic ascended with increasing Φ. They found that ignition timing close to TDC would give rise to an increase in the proportion of exhaust gas energy and a decrease in NOx emissions. They proposed that reasonable adjustment of the coolant temperature could reduce the energy of the whole system, but had little effect on the brake thermal efficiency. Based on the mapping characteristics experiment, Wang et al.32 employed the same equipment and further investigated the distribution of energy and exergy of the engine. The results revealed that all kinds of energies (exhaust energy, cooling medium energy, intercooler energy, uncounted energy, and effective work) increased as speeds increased and they were not sensitive to the loads. They also found that the turbocharger could enhance ηet and the increasing amplitude could reach 4.8%.

By investigating the variation trend of the polytropic coefficient of a 2.0 L HICE, Luo et al.33 found that the polytropic coefficient of the HICE was smaller than that of the gasoline engine. Results from experiments also demonstrated that the polytropic coefficient was decreased as Φ increased. They also found that the polytropic coefficient increased from 1.3 to 1.35 with the increase of engine speed from 1000 to 4000 rpm, and then it decreased to around 1.34 at 5000 rpm. Luo and Sun34 also found that the power output of the turbocharged HICE could be increased and NOx emissions could be controlled by using the Miller cycle, and then the performance of the engine was optimized, especially at a low engine speed.

Sun et al.35 carried out the investigation on the performance of the HICE and vehicle. Results of the test showed that, while the power and torque outputs were 40% lower than those of the gasoline engine, the indicated and brake thermal efficiency of the HICE could reach 40.4% and 35%, respectively. NOx emission was mainly affected by the Φ value of mixed gas. The system of the HICE and vehicle worked normally, and the dynamic properties met the development requirements. In addition, Ma et al.36 predicted the comprehensive performance of a HICE through numerical calculations and determined the optimal cylinder diameter of the engine, and then verified the possibility of the engine to achieve lean combustion. They found that the increased cylinder pressure and the reduced thermal efficiency could be obtained after decreasing λ. They also pointed out that the increase of the compression ratio could enhance the performance of the engine, and the variation of the ignition advance angle had little impact on the indicated thermal efficiency, as shown in Figure 5.

Figure 5.

Figure 5

Variations of indicated thermal efficiency with ignition advance angle.

Yang et al.37 proposed a radial basis function network model for predicting the output of power, consumption of fuel, and emissions of a HICE with the engine operating parameters. Through the training and test, they found that the model can abstractly predict the output performance.

Sun et al.38 conducted experiments to explore the influence regularity of hot EGR on torque and NOx emissions of a 2.0 L HICE by adjusting the EGR rate to change Φ. The experimental results showed that the introduction of hot EGR could increase the intake charge temperature and combustion temperature under partial load, and then lead to an increase in NOx emissions, while NOx emissions were decreased with the increase of EGR rate under full load. They found that the torque was changed slightly with the variation of EGR rate when Φ was less than 1, while the torque was reduced with the increase of EGR rate when Φ was greater than 1. They also proposed that NOx emissions could be dramatically decreased after a three-way catalyst with a slight reduction in torque was adopted. Duan and Liu39 investigated the hydrogen-fueled engine combustion performance and emission characteristics based on a PFI-HICE test system equipped with a hot EGR system. The experimental results showed that using hot EGR could significantly reduce Pmax and Tmax and slightly increase the period of ignition delay and duration of combustion. They also found that when the EGR rate was large enough at middle load, NOx emissions were reduced greatly, but only a moderate EGR rate was needed for NOx emissions control at high load, because an excessive EGR rate would lead to significant reduction in power output and fuel economy. In addition, Sun et al.40 built the turbocharging HICE model to deal with the turbocharging match problems. On this basis, they accomplished HICE turbocharging matching and optimization of compression ratio and intake valve opening timing. The results of performance prediction showed that the maximum torque of turbocharged HICE was 2 times that of the natural aspirated HICE, the efficiency was improved by 7–15%, and the specific emission of NOx tended to decrease.

3.1.2. Research on Nonreciprocating Piston Hydrogen-Fueled Engines

Su et al.41 designed and installed a control system on a rotary engine to explore the idle performance of the engine through changing the duration of hydrogen injection and λ. Results had shown that the decreased fuel energy flow rate, the enhanced stability of engine, the dropped Tmax, and the reduced NOx emissions (as shown in Figure 6) could be obtained with the increase of λ. Besides, Meng et al.42 proposed a combustion speed measurement method for the dual spark plug Wankel rotor engine (HWRE), and associated the flow rate and flame speed with abnormal combustion, and then discussed their impact on the abnormal combustion characteristics of HWRE. The results show that the flame speed and flow rate of HWRE have a significant impact on its abnormal combustion problem, both of which are positively correlated with abnormal combustion, and the latter has a more significant impact (Figure 7).

Figure 6.

Figure 6

Variations of NOx emissions with λ.

Figure 7.

Figure 7

Abnormal combustion at the corresponding flow velocity (a) and forward combustion velocity (b).

Yuan et al.43 established the CFD model of a free-piston hydrogen-fueled engine, and then compared and investigated the effects of pilot-ignition and spark-ignition on the performance of the engine through numerical calculations. They found that the raised combustion velocity of H2–air mixture, the enhanced degree of constant volume combustion, the improved output of power and ηet, and the increased NO emissions could be obtained after adopting the pilot-ignition. Yuan et al.44 then made simulations to investigate the performance of a linear hydrogen-fueled engine (LHE). Results from simulations revealed that the LHE had higher thermal efficiency and indicated power under short stroke, but the postcombustion effect was serious. With the increase of stroke length, the increased combustion velocity, the improved engine efficiency, and the raised NO emissions could be obtained. With the further increase of stroke length, the combustion temperature was decreased and NO emissions were reduced, but the thermal efficiency and output power of the engine were lower at this time. Afterward, Yuan et al.45 employed the same equipment and further investigated the LHE. They found that the uniformity of the hydrogen–air mixture was raised with the increase of stroke length. They also proposed that the LHE with long stroke could achieve homogeneous combustion.

Cao et al.46 analyzed the mode of combustion and operating route of a hydrogen-fueled scramjet engine, determined the boundary of transition of combustion mode, and proposed the optimal operating route for scramjet operation. In addition, Yang et al.47 established a model of a scramjet engine to explore the mechanism of transition of combustion mode at the assumption of inviscid flow. Zhang et al.48 developed the system of thermal protection of the hydrogen-fueled scramjet engine to ensure safety and cooling requirements of the engine at high flight Mach number. Afterward, Yang et al.49 proposed the constant static-temperature heating to solve the restriction of combustion temperature limit on the performance of the hydrogen-fueled scramjet engine and conserve fuel. Results also demonstrated that the efficiency and thrust of the engine were obviously enhanced after adopting this method without overtemperature of the combustor.

3.2. Mechanism and Suppression Method of Abnormal Combustion

Although hydrogen-fueled engines have a series of advantages over a conventional petroleum-fueled engine, such as wide ignition limit, fast combustion velocity, running under lean mixture, and less harmful emissions, if the working process is improperly organized, abnormal combustion is likely to occur. Not only will the engine’s performance decline sharply, but the engines cannot operate normally, and even experience flameout. Therefore, it is necessary to explore the abnormal combustion mechanism and influence factors of hydrogen-fueled engines and strategy of eliminating abnormal combustion. Abnormal combustion of hydrogen-fueled engines is mainly split into the following three categories: (a) the rate of pressure rise is too high in the early stages of combustion and knock; (b) preignition of the combustion process; and (c) backfire of the intake manifold.

These three kinds of abnormal combustion can sometimes transform and promote each other. For example, the continuous advance of preignition can eventually cause backfire; an excessive pressure rise rate tends to create hot spots in the cylinder, which cause preignition and backfire.

Yang et al.50 transformed the pressure signals of normal combustion and preignition by wavelet to investigate abnormal combustion of hydrogen-fueled engines. Through investigating and comparing the spectrum feature of wavelet transform, the wavelet energy of different scales was computed and used to diagnose abnormal combustion. They found that wavelet transform is effective for diagnosing abnormal combustion. Yang et al.51 then discussed the mechanism of abnormal combustion of hydrogen-fueled engines, analyzed the correlation between preignition and rate of pressure rise, and further investigated the approach of diagnostic on preignition. They found that wavelet analysis could be employed to diagnose the timing and severity of preignition at various rates of pressure rise. Results from experiments also revealed that ignition timing and excessive air ratio were the essential factors affecting the rate of pressure rise. By controlling these key parameters, the abnormal combustion of the engines can be fundamentally restricted. Yang et al.52 then investigated the mechanism of preignition and backfire of hydrogen-fueled engine through analyzing the correlation of the following four factors: state parameters, operating parameters, the reaction of chain, and rate of combustion and velocity of propagation of flame. They established the model of optimum control with various variables, objectives, and constraints, and then carried out the solution by GA. They proposed an effective strategy, which was to adjust λ and ignition timing through weighting coefficients to optimize the output of power and suppress the abnormal combustion. In addition, Yang et al.53 pointed out that the delay of ignition timing could contribute to decrease the degree of occurrence of preignition (as shown in Figure 8), and the inclination of backfire could be suppressed by water injection into the inlet (as shown in Figure 9). However, they found that excessive delay of ignition would lead to a reduction in the output of power and brake thermal efficiency. Furthermore, water injection would also cause a reduction in the output of power and make the cylinder suffer more severe corrosion and deteriorate the performance of lubrication. Therefore, they put forward an optimal control method in which the delay of ignition was unified with water injection, which not only eliminated backfire, but took into account the output of power and economy.

Figure 8.

Figure 8

Variations of preignition suppression degree with ignition timing.

Figure 9.

Figure 9

Variations of backfire suppression degree with water injection ratio.

Duan et al.54 built a CFD model with an inlet and cylinder to explore the mechanism of backfire of HICE under conditions of different speeds and loads. They pointed out that the low-temperature and low-concentration mixture could enter the cylinder first to reduce the temperature of exhaust gas or hot spots in-cylinder by adjusting the timing of the H2 injection, thereby controlling the occurrence of backfire. Gao et al.55 then analyzed the inhibiting effects of two types of intake ports, elbow pipe port and tangential intake port, on preignition and backfire through using the 3D numerical simulation method. The results indicated that there was a back-flow elbow pipe port and tangential intake port. Backflow raised the temperature in the intake port, which easily ignited the H2–air mixture in the intake port and caused backfire. They also found that the elbow pipe port was prone to cause preignition, while the tangential intake port helps to restrain preignition. In addition, for investigating the situation of backfire in port injection hydrogen-fueled engines at different loading conditions, Liu et al.56 carried out an experimental investigation on a 2.0 L four-cylinder hydrogen-fueled engine. Results from experiments revealed that when the engine worked at low load condition, the rate of burning of the hydrogen–air mixture was rather low, and a large amount of unburned hydrogen remains, leading to the occurrence of backfire. While at high load conditions, the high temperature fraction of residual gas or hot spots in cylinder ignited the hydrogen–air mixture and caused backfire.

Luo et al.57 employed a 2.0 L hydrogen-fueled engine and established the corresponding model to investigate combustion knock of the engine. Results had shown that combustion knock was more likely to occur when the engine speed was higher. Results from the study also reported that combustion knock interacted with other phenomena of abnormal combustion such as preignition or backfire. On account of combustion knock, the cylinder components were heated, which could generate hot spots and eventually cause preignition and backfire. In addition, to effectively suppress the preignition and harsh combustion in hydrogen-fueled engines, Qin et al.58 attempted the application of a low-temperature combustion technique to a hydrogen-fueled engine, established the prediction model for low-temperature combustion, and analyzed the characteristics and implementing mechanism of low-temperature combustion in hydrogen-fueled engines. They pointed out that low-temperature combustion, which was achieved through enhancing high specific-heat components and reducing oxygen concentration of in-cylinder charge, can effectively control the combustion reaction velocity, suppress the preignition and harsh combustion, and reduce NO pollutant in hydrogen-fueled engine. To explore the preignition of HICE caused by hot spots in depth, Yang et al.59 investigated the influence regularity of feature parameters of a hot surface (especially temperature and area of the hot surface) on the duration of heat of a hot surface. Results from simulations revealed that the duration of heat could be reduced as the temperature and area of the hot surface increased, but the decreasing amplitude was gradually reduced, as shown in Figure 10. When the temperature of hot surface exceeded 1200 K, the area of the hot surface had little effect on the duration of heat. Furthermore, they proposed and defined the critical ignition temperature, which is exclusively controlled by the duration of heat within the scope of the investigation, and then explored the relationship between the critical ignition temperature, duration of heat, and area of the hot surface (as shown in Figure 11). Finally, they reported that eliminating hot spots and controlling the temperature below 800 K before the spark plug ignited were two ways to effectively avoid preignition.

Figure 10.

Figure 10

Variations of heating duration with hot surface temperature under various hot surface areas ((b) is a supplement to (a)).

Figure 11.

Figure 11

Correlation between the critical ignition temperature, duration of heat, and area of hot surface ((b) is a supplement to (a)).

To better investigate the relationship between hydrogen injection parameters and anomalous combustion in hydrogen internal combustion engines, Yang et al.60 applied the AHP decision tree to the research of abnormal combustion of hydrogen-fueled internal combustion engine for the first time, and proposed and defined the “abnormal combustion risk coefficient” based on the AHP-entropy method. Through the comprehensive analysis method, the accuracy and reliability of abnormal combustion diagnosis and control are improved, and the development law of abnormal combustion risk coefficient under different working conditions is deeply revealed, such as the variation trend of mixture uniformity coefficient with hydrogen injection flow rate (Figure 12a) and the variation of temperature of the hot area with hydrogen injection flow rate (Figure 12b). They found that, on this basis, the possibility of abnormal combustion can be reduced by changing the angle and flow of hydrogen injection, which provides a new idea for the diagnosis and control of abnormal combustion.

Figure 12.

Figure 12

Variation trend of mixture uniformity coefficient with hydrogen injection flow rate (a) and variation trend of mixture uniformity coefficient with hydrogen injection flow rate (b) (analyzed by the AHP–AHP entropy method).60 Reprinted with permission from ref (60). Copyright 2023 Elsevier.

Dang et al.61 established a fault diagnosis model for abnormal combustion by integrating the SOM neural network and multiagent system (SOM-MAS) to identify four different types of combustion: normal combustion, slight early combustion, medium early combustion, and heavy early combustion. It is found that the SOM-MAS method can not only diagnose and identify different combustion types, but also find the location of abnormal combustion faults, which provides a new method to solve the problem of abnormal combustion of the hydrogen-fueled internal combustion engine.

The working process of the hydrogen-fueled engine is extremely complex, and the generation mechanism of abnormal combustion determines its instantaneity and uncertainty. Abnormal combustion will not only reduce the performance of the hydrogen-fueled internal combustion engine, but also cause irreversible damage to the hydrogen-fueled internal combustion engine in serious cases. The control of abnormal combustion of hydrogen-fueled internal combustion engines may be the key to determining whether the hydrogen-fueled internal combustion engine can make breakthroughs in the future, so finding an effective way to solve the problem of abnormal combustion of the hydrogen-fueled internal combustion engine is the goal of researchers in the future. The important research on the mechanism and suppression method of abnormal communication from China and their main contributions are summarized in Table 2.

Table 2. Mechanism and Suppression Method of Abnormal Combustion in China.

researchers experimental equipment main methods main contributions
Yang et al.49 (2008) the hydrogen-fueled engine used in the experiment is modified from a three-cylinder and two-stroke engine; the cylinder × diameter stroke: 61 × 61.5, emission capacity 539 cc, half ball firebox, compression ratio 6.9:1 signal processing methods wavelet analysis is effective for diagnosing abnormal combustion
Yang et al.50 (2010) a single-cylinder, four-stroke hydrogen-fueled engine; the engine is water-cooled horizontal type; its displacement is 482 cm3, bore is 85 mm, stroke is 85 mm, compression ratio can be changed from 4.8 to 7.93 hemisphere signal processing and control model ignition timing and excessive air ratio were the essential factors affecting rate of pressure rise
Yang et al.52,53 (2012) as the above control model method the propagation speed of laminar flames is related to the state and operating parameters of hydrogen fuel engines; among them, temperature, pressure, boost rate, and excess air ratio have the greatest impact on abnormal combustion
Qin et al.58 (2017) as the above CFD methods low-temperature combustion technology can reduce the rough working characteristics of hydrogen internal combustion engines
Gao et al.55 (2014) as the above, but using two valve intakes CFD methods the impact of different inlet ports on abnormal combustion
Yang et al.60 (2022) as the above, but using a four-valve structure CFD and data processing verified the applicability of AHP method in the study of hydrogen injection angle and flow rate on early ignition and tempering of hydrogen internal combustion engines
Duan et al.54 (2013) a 4-cylinder, 1.998 L, PFI hydrogen internal combustion engine with intake port injection, with a bore of 86 mm and a stroke of 86 mm CFD methods optimizing the angle of hydrogen injection can effectively suppress backfire and investigate the reasons for abnormal combustion in hydrogen internal combustion engines with different loads
Liu et al.56 (2014) as the above experimental study experimental evidence on the causes of abnormal combustion in hydrogen internal combustion engines with different loads
Luo et al.57 (2016) as the above experimental and numerical model analysis in the PFI hydrogen internal combustion engine, the effects of ignition timing and backfire on combustion knock were explained
Yang et al.59 (2018) not mentioned experimental study explored the importance of the influence of various parameters on the hot spots of hydrogen internal combustion engines
Dang et al.61 (2022) a 539 cm3 hydrogen internal combustion engine with a hemispherical combustion chamber, with a cylinder diameter of 61 mm and a piston stroke of 61.5 mm neural network algorithm the SOM neural network can effectively detect abnormal combustion problems such as pre ignition, backfire, and detonation in hydrogen engines, and propose a Multi Agent System to locate and track faults

3.3. The Influence of Hydrogen Injection Parameters and Hydrogen Injection Modes on HICE

As analyzed in the previous section, hydrogen injection parameters are one of the important influencing factors for abnormal combustion. When hydrogen fuel is supplied to a HICE by means of intake manifold injection, the blockage of the intake pipe could occur. Especially, when the engine runs at high load, it has to face the contradictions between the blockage of the intake pipe, the abnormal combustion, and the decline of the power output of the engine. The hydrogen injection parameters and the hydrogen injection modes have a great influence on the blockage of the intake pipe and the formation of H2–air mixture, which has an essential effect on the abnormal combustion, engine’s performance, and NOx emissions. Therefore, it is essential to reveal the influence law and the formation of the hydrogen–air mixture.

Liu et al.62 made numerical and experimental investigations on a PFI-HICE and then proposed a limited injection end timing of the HICE to rotating condition of the engine for preventing backfire (Figure 13). Sun et al.63 combined experiment with simulation to explore the characteristics of the hydrogen injector of the HICE. They established an area of circulation between sealing elements and armature to possess the greatest impact on the flow characteristics of the injector and obtained greater flux through adjusting the correlative parameters of the injector. They then pointed out that the raised range of pressure fluctuation and the increased decay time of pressure could be obtained after increasing the supply pressure. They also reported that the pulse-width of injection had the least effect on pressure fluctuation. The parameter correlation is shown in Figure 14.64

Figure 13.

Figure 13

Hydrogen distribution of different injection ends.62 Reprinted with permission from ref (62). Copyright 2008 Elsevier.

Figure 14.

Figure 14

Analyses related to the on-time performance of hydrogen injectors. (a) Changes in opening area, pressure of the injector input, and pressure sensor over time. (b) Pressure fluctuations under different pulse widths at 0.45 MPa. (c) Pressure fluctuations under different pulse widths at 0.45 MPa. (d) Pressure changes with time under different supply pressures.64 Reprinted with permission from ref (64). Copyright 2013 Elsevier.

Duan and Liu65 investigated the impacts of hydrogen injection pressure (HIP) and timing (HIT) on H2–air mixing velocity and uniformity, and put forward the nonuniformity coefficient to evaluate the mixing condition of the hydrogen–air mixture. They optimized the injection timing and pressure of different engine speeds and equivalent ratios according to the nonuniformity coefficients. Duan and Liu66 employed the same equipment and made experiments and simulations to investigate the impacts of HIT and HIP on backfire. They proposed that reasonable optimization of HIT and HIP could enhance the output of power of the engine and suppress backfire at high speed. In addition, the maximum torque could come up to 132 N m when HIT and HIP were optimized, which was 31.49% higher than that of the original engine.

Yang et al.67,68 have carried out detailed research on the hydrogen injection mode. They compared and analyzed single injection (SI) and dual injection with symmetric (SY) or spaced (SP) distribution through simulation, and then pointed out that the adoption of dual injection could enhance the problem of inlet blockage of the PFI-HICE. Results from the simulations demonstrated that am enhanced uniformity of mixture (as shown in Figure 15), an increased velocity of combustion, and the raised NOx emissions could be obtained under various equivalence ratios after applying dual injection, especially spaced dual injection. They proposed that reasonable optimization of the diameter of the nozzle could raise the uniformity of the mixture and improve the power and economy of the HICE. Furthermore, the spaced dual injection would lead to a rise in the temperature of the cylinder, an expansion in high temperature area, and a reduction in residual hydrogen mass in inlet. Although the engine was more prone to preignition, it could suppress backfire.

Figure 15.

Figure 15

Variations of uniformity coefficient of mixture with engine speed under three injection modes.

At the same time, on this basis, the relieving effect of single-way injection and dual-way injection on the inlet blockage of the hydrogen-fueled engine is further studied, and a new injection method, the other side spacing along the inlet shaft (SH injection), is proposed. The results show that, as compared to single-way injection, dual-way injection can not only improve the space–time distribution of the mixture in the inlet, increase the effective flow area, and ease the inlet blockage, but also improve the charging coefficient, increase the uniformity of the mixture, and improve the combustion process.

In addition, the group of Yang69−73 has carried out relevant research on the combustion process and formation of the hydrogen–air mixture of HICE in different parameters of hydrogen injection, such as HIT, HIP, hydrogen injection quantity, and position and diameter of nozzle hole, and various modes of hydrogen injection, such as single pipe injection and dual injection with symmetric and spaced distribution.

With increasingly in-depth research on hydrogen-fueled injection parameters and methods of hydrogen-fueled engine, researchers found that the flow rate and injection mode of hydrogen-fueled injection have a great impact on alleviating the inlet blockage of the hydrogen-fueled engine and improving the output power of the hydrogen-fueled engine. Therefore, researchers can start from these two aspects to achieve the ultimate goal of improving the comprehensive performance of hydrogen-fueled engines. The important research on the influence of hydrogen injection parameters and hydrogen injection modes on HICE from China and their main contributions are summarized in Table 3.

Table 3. Influence of Hydrogen Injection Parameters and Hydrogen Injection Modes on HICEs in China.

research experimental equipment main methods main contributions
Liu et al.62 (2008) a DOHC V4 1.998 L PFI hydrogen internal combustion engine, with a bore of 86 mm and a stroke of 86 mm; two injectors per cylinder experimental research and CFD methods the possibility of backfire mainly depends on the concentration of H2 residual at intake ports in a manifold injection H2ICE, and the leaner is the concentration of the residual, the lower is the possibility of the backfire
Sun et al.63,64 (2012 and 2013) as the above original design and numerical analysis the flow area between the armature and the seal was established to have the largest effect on the injector’s flow characteristics; a low supply pressure exhibits more effectively decreases on pressure fluctuation at a sufficient hydrogen flow
Duan and Liu65 (2014) as the above experimental research and CFD methods greater contact area through turbulence and increased hydrogen diffusion rate result in better mixing performance
Duan and Liu66 (2014) as the above experimental research and CFD methods backfire can be controlled effectively by optimizing hydrogen injection timing to reduce the concentration of the mixture gathering around the intake valve when the latter opens and the temperature of the high-concentration mixture when it flows through the intake valve
Yang et al.67,68 (2018 and 2022) a single-cylinder, four-stroke hydraulic fueled engine; the engine is water cooled horizontal type; its display is 482 cm3, bore is 85 mm, stroke is 85 mm; using dual injection mode for hydrogen injection numerical model analysis and experimental analysis the opening time of the inlet valve and the closing time of the exhaust valve are different, and the timing of hydrogen injection has different effects on the time when the inlet duct is blocked
Yang et al.69−73 (from 2015 to 2018) as the above, but using different injection methods numerical model analysis, experimental analysis, and CFD methods a series of studies have been conducted to illustrate the effects of different parameters on engine hydrogen injection, such as HIT, HIP, hydrogen injection quantity, position and diameter of noise hole, and different modes of hydrogen injection

3.4. The Formation of H2–Air Mixture and Combustion Cycle Variation

Good formation of H2–air mixture is the prerequisite and necessary condition to ensure the normal combustion of HICE and is also the basis to improve the performance of HICE. However, in the research of hydrogen internal combustion engines, due to the lack of corresponding equipment, it is difficult to directly study the fuel concentration distribution and evolution characteristics of the H2–air mixture. The visualization analysis method based on CFD has gradually become one of the main research methods for HICEs with the development of computers.

Yang et al.74 proposed that the adoption of the CFD model was conducive to investigate the formation rule of the H2–air mixture of hydrogen-fueled engine. They pointed out that the hydrogen injection timing had an essential effect on the formation of the mixture. Properly advancing the hydrogen injection timing could enhance the quality of the mixture (Figure 16). In addition, Wang and Liu75 made the simulative study on the distribution of mixture and position of ignition in a direct-injection HICE. They analyzed the characteristics of hydrogen concentration distribution for several special positions in the cylinder and found that the hydrogen concentration in the two characteristic positions away from the nozzle in the cylinder was more stable than the concentration of H2 near the spark plug, and the installation of spark plug away from the nozzle is more conducive to ignition.

Figure 16.

Figure 16

Mass fraction of H2 on the section plane of x = 0 at different crank angles.74 (a) Mass fraction of H2 at 261 °CA. (b) Mass fraction of H2 at 320 °CA. (c) Mass fraction of H2 at 321 °CA. (d) Mass fraction of H2 at 330 °CA. (e) Mass fraction of H2 at 340 °CA. Reprinted with permission from ref (74). Copyright 2010 Elsevier.

Hydrogen can form a leaner combustible mixed gas than gasoline, which is beneficial for hydrogen-fueled engines to exploit lean combustion to improve fuel economy and emissions. Nonetheless, the application of lean mixture increases the combustion cycle variation, which affects the combustion efficiency and emissions of hydrogen-fueled engines to some extent. Hence, it is obligatory to research the cycle variation of hydrogen-fueled engines.

Sun et al.76 proposed that the optimum parameter to reflect cycle variations of HICE is CoVimep. On this basis, Sun et al.77,78 employed the same equipment to further verify the above conclusion and then studied the cycle variation of the engine. They pointed out that the increase of idle speed, H2–air mixture concentration, and throttle opening (0–20%) would lead to the decrease of CoVimep of the HICE. When the H2–air mixture concentration was high, the impact of θig on CoVimep became weaker, and θig that corresponded to minimum CoVimep decreased with the increase of Φ, as shown in Figure 17. In addition, Wang and Ji et al.25 proposed that when the hydrogen-fueled engine was running at idle speed, the combustion duration was gradually prolonged with the increase of λ, and the cyclic variation was also slightly raised, but it could still remain at a relatively low level.

Figure 17.

Figure 17

Variations of CoVimep with ignition advance angle.

The important research on the formation of the H2–air mixture and combustion cycle variation from China and their main contributions are summarized in Table 4.

Table 4. Formation of H2–Air Mixture and Combustion Cycle Variation in China.

research experimental equipment main methods main contributions
Yang et al.74 (2010) the hydrogen-fueled engine used in the experiment is modified from a three-cylinder and two-stroke engine; the cylinder × diameter stroke: 61 × 61.5, emission capacity 539 cc, half ball firebox, compression ratio 6.9:1; injector is fixed in the center position of cylinder cover, injection valve turns on controlled by rocker arm through camshaft, and the camshaft keeps the same rotating speed as crank CFD methods the CFD method is very effective for studying the state of the mixture in hydrogen internal combustion engines; in this example, the mixture quality is much better than other two circulations, which was injected at 260 °CA
Wang and Liu75 (2010) the spark plug is located in the center of the cylinder, with a 12-hole nozzle installed on the side, relatively close to the spark plug; case 1 is to have a spray hole facing the spark plug; case 2 involves rotating the nozzle 15° to position the spark plug between two jet streams Schlieren experiment and CFD methods the hydrogen concentration in the two characteristic positions far from the nozzle in the cylinder is more stable than that near the spark plug; research on the distribution of hydrogen concentration in the cylinder has found that installing the spark plug away from the nozzle is more conducive to ignition and combustion
Sun et al.76 (2013) a V4 1.998 L PFI hydrogen internal combustion engine, bore is 86 mm, stroke is 86 mm experimental analysis CoVIMEP is the best characteristic parameter for evaluating the cyclic variation characteristics of PFI hydrogen internal combustion engines
Sun et al.77,78 (2013) as the above experimental analysis through experimental research, the effects of rotational speed, ignition advance angle, mixture concentration, throttle opening, and initial hydrogen injection angle on the cyclic variation of PFI hydrogen internal combustion engines were studied
Wang and Ji et al.25 (2011) a 1.6 L pure hydrogen engine modified from a gasoline engine with a cylinder diameter × piston stroke: 77.4 × 85 mm, with electronically controlled hydrogen injection through the intake port experimental analysis due to the decrease in fuel combustion speed during lean burn, the constant volume combustion efficiency of pure hydrogen engines decreases with an increase in excess air coefficient under idle conditions

3.5. NOx Emissions

Hydrogen-fueled engines have incomparable advantages over conventional petroleum fueled engines in terms of the harmful emissions. The only harmful emission is NOx (the harmful emissions of CO, HC, and soot produced by the lubricating oil entering the combustion chamber, which are negligible, can be ignored). Although it is relatively simple to control single harmful emissions than several harmful emissions at the same time, it is not easy to effectively suppress NOx emissions without sacrificing other performance indexes.

Xu et al.79 explored the impacts of λ on the cold start of a hydrogen-fueled SI engine. Results had shown that NOx emissions were raised (as shown in Figure 18) and the temperature in the exhaust manifolds was declined with the increase of λ when the engine was started for 6 s. They also found that the engine speeds increased with the decrease of λ in the first 6 s. They80 then employed the same equipment and made further experiments under cold start condition and various timings of ignition (IT) when λ was 0.7. They found that the shortest successful start time and the highest Pmax could be obtained in the first cycle at 15 °CA BTDC. In addition, NOx emissions were lowered by 90.2% on average in the first 6 s with the postponing of IT. Bai81 also changed the pulse width of hydrogen-fueled injection λ. The combustion and emission characteristics of the hydrogen-fueled internal combustion engine at cold start were studied. The results show that when λ is gradually reduced from 1.54 to 0.72, the peak starting speed gradually rises within 6 s before the cold start of the hydrogen-fueled internal combustion engine. At the same cycle number, the flame development period and rapid combustion duration are λ. The decrease of the ratio of the two shows a trend of gradual shortening; NOx emission shows a change rule of rising slightly at first and then decreasing gradually. The peak and average NOx emissions are the highest at λ = 1.41.

Figure 18.

Figure 18

Variations of NOx emissions with excessive air ratio.

Moreover, Liu82 carried out the starting experimental research with equivalent fuel air ratio 0.2–0.6 on a four-cylinder, 2.0 L HICE through using the different methods of control fuel air ratio. The experimental results showed that the start-up time decreases with the increase of fuel flow for qualitative control. However, the NOx emissions would increase significantly. With increasing throttle value, the air flow would increase that reduced the pumping losses and increased the volumetric efficiency, consequently decreasing the start-up time to a certain extent, but NOx emissions would increase in a small amount.

Wang et al.83 studied and analyzed the combustion behavior of the hydrogen-fueled–air mixture with a dilution ratio of 0–50% under EGR and lean combustion strategies. Furthermore, the influence of water vapor in EGR on the combustion of the hydrogen-fueled–air mixture was further studied. The results show that the formation of NO can be inhibited by increasing the water vapor fraction in EGR. However, the unburned H2 emission in the final product will increase with the increase of water vapor fraction. Therefore, within the test range, when the EGR rate is 30% and the water vapor fraction is 20%, the NO emission can be controlled while taking into account the actual combustion efficiency. In addition, Li et al.84 used Chemkin Pro software to simulate and compare the combination of EGR, EGR technology and lean combustion, as well as the internal selective noncatalytic reduction technology. The results show that the internal selective noncatalytic reduction technology has a better NOx emission control effect than do the EGR technology and EGR–lean combustion technology. Only a 10% ammonia ratio can reduce the NOx emission of pure hydrogen-fueled engine by 96.32%, while a 15% ammonia ratio can achieve zero NOx emission of a pure hydrogen-fueled engine without the participation of EGR or lean combustion technology.

Duan et al.85 made simulations to explore the NOx formation mechanisms of the HICE under high load. Results from simulations demonstrated that NO emissions were the primary components of NOx emissions, which were chiefly generated by thermal NO, NNH, and N2O, in which thermal NO accounted for the largest proportion. They pointed out that NO was generated in large quantities with the increase of temperature during the rapid combustion period, and then the production of NO was decreased to a stable level when the temperature in the cylinder dropped below 2200 K. On this basis, Zhu et al.86 built a CFD model of the HICE to investigate the combustion process and NO generation mechanism. Results had shown that the peak mass of NO was raised with the increase of Tmax. The fast reduction of temperature in-cylinder could restrict the decomposition of NO. They also found that EGR could reduce the peak temperature in the cylinder, thereby reducing NO emissions, as shown in Figure 19. Duan et al.87 also simplified the hydrogen–air detailed reaction mechanism and studied its applicability in a wide range of λ values. They pointed out that the instantaneous cylinder pressure and NOx emissions of the CFD model with the simplified mechanism could be accurately predicted.

Figure 19.

Figure 19

Variations of NO emission concentrations with EGR rate.

Luo et al.88 pointed out that when the hydrogen-fueled engine adopted turbocharging technology, the power output was dramatically increased and the stability of combustion was effectively improved under low engine speeds and various equivalence ratios. They also found that the NOx emissions were almost reduced to below 20 ppm, and the engine comprehensive performance was enhanced after using the strategy of H2+TWC. Luo et al.89 employed the same equipment and further investigated the combustion velocity and NOx emissions of the engine. They found that the combustion duration (CA10–90) was equal to or much longer than that of the other loads at 0.27 MPa BMEP and various engine speeds of 1500 and 2000 rpm. Moreover, NOx emissions increased and even reached 7000 ppm after the engine speed was increased.

Sun et al.90 made experiments to probe the characteristics of combustion and NOx emissions of a 2.0 L HICE, and examined the correlations between NOx emissions and both equivalence ratio Φ and ignition timing. Experimental results showed the following: at Φ = 0.88, the NOx emissions reached maximum value; when Φ was below 0.88, the NOx emissions increased with Φ increasing, and when Φ was in the range of 0.88–1.2, the NOx emissions decreased quickly with increasing Φ. For a lean mixture, the effect of ignition timing on NOx formation was relatively small. Duan et al.91 conducted tests to explore the impacts of Φ, ignition advance angle, exhaust gas recirculation (EGR), and engine speed on the NOx emission from a four-cylinder PFI-HICE. Results from the tests demonstrated that Φ was the key factor to the formation of NOx. When Φ was larger than 0.5, the NOx emissions increased quickly with Φ and reached its peak (10 000 × 10–6) at a Φ value of around 0.9; when Φ was in the range of 0.5–0.7, the retard in ignition angle leads to the great reduction in NOx emissions, and the lower was the engine speed, the greater was the reduction in NOx emissions. The adoption of hot EGR also resulted in an obvious fall in NOx emissions. Furthermore, the lower was the engine speed, the greater was the decrease in NOx emissions.

The important research on NOx emissions of HICEs from China and their main contributions are summarized in Table 5.

Table 5. Study on NOx Emissions of HICEs in China.

research experimental equipment main methods main contributions
Xu et al.79,80 (2018 and 2019) a 1.6 L pure hydrogen engine modified from a gasoline engine with a cylinder diameter × Piston stroke: 77.4 × 85 mm, with electronically controlled hydrogen injection through the intake port experimental analysis during the cold start period, NOx emissions that obviously raise at lean combustion conditions could efficiently reduce by rich H2 combustion strategy; moreover, the emitted HC and CO emissions found in the exhaust manifold increase with the decrease of l due to the evaporated lubricant oil
Bai81 (2019) as the above experimental analysis and CFD methods under rich combustion conditions, neither too early nor too late ignition is conducive to improving the cold start performance of a hydrogen internal combustion engine; with an excess air factor of 0.72, when the ignition angle is delayed from 25 °CA BTDC to 10 °CA ATDC, the cold start time of a hydrogen internal combustion engine is shortened and then lengthened, and the peak in-cylinder combustion pressure is also shown to be increasing and then decreasing, and the shortest cold start time and highest peak cylinder pressure are found at an ignition angle of 15 °CA BTDC; at an ignition angle of 15 °CA BTDC, the hydrogen internal combustion engine has the shortest successful cold start time and the highest peak cylinder pressure
Liu82 (2012) a V4 1.998 L PFI hydrogen internal combustion engine, bore is 86 mm, stroke is 86 mm experimental analysis increasing the amount of hydrogen injected in the cycle and increasing the mixture concentration can effectively increase the output torque of the hydrogen engine and shorten the start-up time, but at the same time, the NOx emission will increase rapidly
Wang et al.83 (2022) a cylinder with a 120 mm inner diameter and 200 mm length experimental analysis increasing dilution level could achieve zero NO emission in the final product; for low diluent fractions, EGR has a more significant effect on reducing NO; it should be noted that the unburnt H2 fraction sharply increases when the EGR fraction exceeds 40%
Li et al.84 (2021) not mentioned CFD methods the use of EGR technology to achieve ultralow NO emissions from hydrogen-only engines requires the use of larger EGR ratios or a combination of EGR and external purification
Duan et al.85 (2017) a 2.0 L, four cylinders, and four strokes, naturally aspirated, spark ignition engine CFD methods NO is the main component of NOx emissions, accounting for more than 97% of the total high load NOx emissions; N2O concentration increases sharply during the combustion period; the final N2O concentration is less than 1 ppm; NO2 emissions increase rapidly during the fast combustion period, and the increase slows after the fast combustion period; the final concentration is 30–60 ppm, which accounts for 2% of the total NOx emissions
Zhu et al.86 (2019) as the above CFD methods the combustion of hydrogen in the cylinder undergoes two stages: ellipsoidal flame stable propagation and rapid turbulent combustion
Duan et al.87 (2019) as the above CFD methods the most important reaction that affects the combustion of hydrogen; the generation of NO depends not only on the combustion process of hydrogen, but also on the three most important paths: the thermal NO, NNH, and N2O route
Luo et al.88 (2019) a 2.3 L, four strokes, PFI hydrogen engine with a turbocharger was installed into a hydrogen engine test bench experimental analysis increasing equivalence ratio can not only ascend the power, but the BTE also increases within a certain equivalence ratio range (such as 0.6–0.8) because the equivalence ratio can speed up the combustion velocity and improve the gas exchange process at low engine speeds of turbocharged hydrogen engines
Luo et al.89 (2019) as the above experimental analysis the turbocharger affects the trend of combustion duration with engine speed; when the turbo fails to absorb enough exhaust gas energy, the residual gas fraction increases and combustion slows, resulting in equal combustion durations at 1500 and 2000 rpm; the results at 2500 rpm, λ = 0.55, and at different loads also support this conclusion; this is a clear difference in combustion characteristics between turbocharged and naturally aspirated engines
Sun et al.90 (2011) an inline four-cylinder 1.998 L PFI hydrogen combustion engine, bore is 86 mm, stroke is 86 mm; two injectors per cylinder experimental analysis at different equivalence ratios, the NOx generation increases with the increase of ignition advance angle, but the torque increases first and then decreases; in the case of lean combustion, it is possible to increase the torque while meeting the NOx emission requirements by choosing a suitable ignition advance angle
Duan et al.91 (2014) as the above experimental analysis the use of EGR can significantly reduce NOx emissions, and the higher is the EGR rate, the more significant is the effect of EGR in reducing the peak NOx emissions and the range of high concentration zones; the larger is the EGR rate, the more significant is the effect of EGR in reducing the peak and high concentration areas of NOx emissions; the lower is the speed, the more significant is the effect

3.6. The Optimization Control Method of the Combustion Process

It is well-known that the optimization control of the combustion process is an important means of improving the performance of the internal combustion engine. It is also an effective means to inhibit or eliminate the preignition and backfire especially for the hydrogen-fueled internal combustion engine. The optimization control of the combustion process is generally achieved by the optimization control of the ignition timing, fuel injection timing, and injection quantity of the engine.

Conventional engines generally take operating parameters, such as ignition timing, injection timing of fuel, and quantity of injection, as the basic control parameters, and take power, economy, and emission performance as the optimal objectives to carry out open-loop control of the engine. However, the influences of operating parameters on the performance indexes of the engine, as power, economy, and emission performance, etc., are generally different and even contradictory under all operating conditions of the engine. Therefore, it is impossible to achieve the optimum performance of all performance indexes under all operating conditions at the same time. Yang et al.4 proposed the optimal ideas that some should be selected as the optimal objectives from the performance indexes according to the different conditions of the engine. That is to say, the corresponding performance indexes are selected as the main goal to achieve the optimum under different operating conditions, and it should be given consideration to other performance indexes.

Yang et al.92 researched the performances of a hydrogen-fueled engine through changing ignition and injection timing. They applied a control system composed of a FNN controller and an ignition adaptive controller to the engine to effectively regulate ignition and injection timing, and the mass of H2 supplied per cycle. Finally, the comprehensive performance of the engine was dramatically enhanced under various operating conditions. On this basis, Yang et al.93 applied the established fuzzy-neural network (FNN) control system to control optimization of the ignition timing, and adopted an improved FNN system as a substitute for the traditional ignition timing map obtained by experiments for optimization of the ignition timing. The calculating results with the FNN system were in good agreement with the experimental measurements.

Based on the experiments, Yang et al.94 put forward the strategy of an optimal control on HICE, and set up an optimal control model, in which timing of spark, injection timing, and duration of injection were selected as mutable variables, and power output and specific fuel consumption were selected as the functions of performance indicators, and then we proposed the idea and method to calculate the optimal control model. Furthermore, based on the established model of the engine, they also set up a control system, which connected fuzzy-neural network (FNN) controllers to an adaptive controller for ignition time to implement open loop or closed loop control mode by gradually adjusting timing of spark, to realize optimal control of the combustion process. The principal diagram of two kinds of control modes is shown in Figure 20. Eventually, they ingeniously designed the FNN system to figure out and predict the laws of optimal control for the model of optimal control and to realize the optimal control of the combustion process. The results also revealed that the computational strategy with the FNN system had higher superiority.

Figure 20.

Figure 20

Principal diagram of two kinds of control modes.

Yang et al.95,96 established a model with an optimal control strategy, which was about the relationship between the power, economy, emission performances, and operating parameters of HICE, and combined decision partiality with the operating conditions of the engine through the multiobjective optimization algorithm, which was unified with Pareto rank and decision partiality. That is, decision partiality introduced in the Pareto method was endowed the characteristic that realized dynamic adjustment according to the operating parameters of the engine, and the optimization procedure of the multiobjective was conducted in the optimization procedure to obtain optimality of the solution’s Pareto. It solved the problem of solving the model and improved the efficiency of the solution. The control’s response speed and controlling precise were further improved through integrating segmental multiobjective optimal control of the combustion process into optimal control of a single target. It developed a novel way to figure out the control problems of multiplication and complexity of the optimized targets for the engines.

Wang et al.97 pointed out that optimal control of the combustion process is the most valuable method for figuring out the conflict of inhibiting abnormal combustion and enhancing output of power for the hydrogen-fueled engine. This method combined the strategy of nonlinear programming with genetic algorithm (GA). They used the method to establish a mathematical model of full work conditions, which took into account the enhancement of comprehensive performance and inhibition of abnormal combustion, then proposed a novel way to precisely and promptly calibrate MAP at various conditions, which successfully figured out the conflict mentioned above. Thereafter, Wang et al.98 further investigated the optimization control method of a system of nonlinear combustion for hydrogen-fueled engines by combining ways of thermodynamic analysis with ways of state space analysis. They established the model of optimal control for hydrogen-fueled engines and utterly revealed the inner logical relation through optimally controlling operating parameters, adjusting state parameters, enhancing indicators of performance, and inhibiting abnormal combustion. This laid a method foundation for the optimization control of the combustion process.

In addition, Wang et al.99 constructed the ignition timing optimization model of hydrogen-fueled engines through adopting the L–M neural network algorithm. As compared to the BP algorithm and Powell algorithm, the L–M algorithm had a better optimization effect. The calibration and optimization control of the ignition timing of the engines at full working conditions were realized. Wang et al.100 then proposed an optimization model and optimization method based on the genetic information fusion algorithm. The experiments showed that the economic and dynamic performance of the hydrogen engine would be enhanced through optimizing two operating parameters of λ and θig.

In addition, Yang et al.101 used the multipopulation genetic algorithm to solve and analyze the comprehensive optimization model of the hydrogen-fueled engine, and further studied the optimization control method of the combustion process of the hydrogen-fueled engine. The results show that by optimizing the ignition timing and hydrogen injection timing of the hydrogen-fueled engine, the goal of improving the combustion performance of the hydrogen-fueled engine can be achieved, which provides a new method for studying the combustion process of the hydrogen-fueled engine in the future.

The important research on the optimization control method of the HICEs combustion process from China and their main contributions are summarized in Table 6.

Table 6. Study on the Optimization Control Method of the HICEs Combustion Process from China.

research experimental equipment main methods main contributions
Yang et al.4 (2001) a 165F petrol engine with a capacity of 126 cm3 experimental analysis the ignition timing, injection timing, and hydrogen injection amount of an engine have a significant impact on engine performance, abnormal combustion, and NOx emissions
Yang et al.92 (2002) the test engine was modified by a water cooled, 4-cylinder, 4-stroke diesel engine with 96 mm bore, 102 mm experimental analysis the use of electronic control system has advantages for achieving the purpose and improving the performances of hydrogen-fueled engine, FNN controller is a promising alternative as compared to the many man-hours of work required to develop the algorithms and look-up tables of a conventional system
Yang et al.93 (2003) as the above experimental analysis the fuzzy neural network system for optimizing the control of ignition advance angle has less experimental workload as compared to the conventional MAP control method and has more advantages when considering that the control variable ignition advance angle is a function of multiple variables (multiple influencing factors); in addition, this network topology structure also has advantages in reflecting the nonlinear relationship between output (ignition advance angle) and input (engine speed and load, etc.)
Yang et al.94 (2003) as the above experimental analysis and mathematical models the combustion mechanism of engines is very complex, and the high nonlinearity and imprecision of engine modeling make it difficult to establish analytical expressions in the state space; fuzzy mathematics, artificial neural networks, and computational science may be more suitable
Yang et al.95 (2008) a single-cylinder hydrogen-fueled engine, which is modified from a gasoline engine; the cylinder diameter × stroke is 84 × 90 mm, and the combustion chamber is half ball, and the compression ratio is 8.5 mathematical model analysis propose a fully automatic optimization control algorithm that combines Pareto improvement with local decision-making; the multiobjective parallel optimization process in the optimization process can effectively achieve the combination of single optimization and combined performance optimization; in the fitness function, add the weighted sum of multiple objective values to the fitness function; the weighting function of each objective varies with changes in operating status; therefore, the optimization process of hydrogen fuel engines develops toward dynamic optimization of hydrogen fuel engine performance based on the operating status of the engine
Yang et al.96 (2008) as the above experimental simulation propose an optimization control algorithm that combines genetic algorithm to unify the control of variables, objectives, and operating conditions into a multiobjective integrated optimization control technology
Wang et al.97 (2010) as the above experimental simulation by adding genetic algorithms, the MAP calibration process can be simplified, the calibration speed and accuracy can be improved, and the global optimal solution can be obtained
Wang et al.98 (2012) as the above experimental simulation a state space model for the nonlinear combustion control system of hydrogen fuel engines has been established, achieving an equivalent transformation from the state space model to the optimal control model represented by the main operating parameters and performance indicators; this lays the foundation for improving performance indicators and eliminating abnormal combustion by optimizing control operating parameters
Wang et al.100 (2017) as the above control method model and genetic algorithm an optimization model and method based on genetic information fusion algorithm have been proposed; by optimizing the operating parameters of excess air coefficient and ignition advance angle, the economy and power performance of hydrogen engines will be improved; the experiment shows that the method used in this Review is reliable and practical
Wang et al.99 (2016) a single-cylinder, four-stroke hydrogen-fueled engine; the engine is water-cooled horizontal type; its displacement is 589 cm3, bore × stroke: 94 × 85 mm control method model and neural network a hydrogen fuel engine ignition timing optimization model based on L–M neural network algorithm was constructed to achieve calibration and optimization control of hydrogen engine ignition timing under all operating conditions
Yang et al.101 (2022) as the above control method model and improved genetic algorithm with the delay of hydrogen injection timing and ignition timing, the indicated power and indicated thermal efficiency first increase and then decrease; in terms of emissions, the NO emissions at medium loads are significantly higher than those at high and low loads; in addition, with the delay of hydrogen injection time, the NO mass fraction first increases and then decreases at low and medium loads, and continues to increase at high loads; with the delay of ignition time, the NO mass fraction decreases

4. Results and Discussion

Since the beginning of the 21st century, Chinese researchers have made great efforts and progress in the field of HICE. These advances mainly focus on the structural form of different HICEs, the mechanism and suppression method of abnormal combustion, the influence of hydrogen injection parameters and hydrogen injection modes on HICE, the formation of H2–air mixture and combustion cycle variation of NO parameters and hydrogen injection modes on HICE, NOx emissions, and the optimization control method of the combustion process.

The hydrogen internal combustion engine has near zero emission (except NOx) and higher efficiency than the conventional fossil fuel internal combustion engine, which make it have extreme widespread prospects. Yet, the multiyear studies in the HICE of North China University of Water Resources and Electric Power clearly show that abnormal combustion, such as preignition, backfire, and the blockage of intake pipe, is likely to occur, especially when the engine runs at high load, and the hydrogen injection parameters and the hydrogen injection modes have an essential effect on the blockage of the intake pipe and the formation of H2–air mixture, which has an important impact on abnormal combustion, engine performance, and NOx emissions, and the optimal control of the combustion process is the most valuable method for resolving the contradictions among inhibiting abnormal combustion, the blockage of intake pipe, and improving hydrogen-fueled engine power. Besides, with the gradual maturity of hydrogen production technology, the continued perfection of hydrogenation infrastructure, and the consistent breakthrough in the area of investigation on HICE, the technology of Chinese HICEs will be increasingly advanced.

5. Conclusion

As a form of hydrogen energy application in the field of transportation, at this stage, HICEs have the advantage of being difficult to replace in a short time in some aspects. In addition to the supporting facilities of hydrogen, by reviewing the development of HICEs, we can see that with the development of computer levels, more digital methods have been applied to internal combustion engines, such as more mature CFD software and more intelligent body agent calculation methods, which are also crucial for the development of HICEs, and, in the future, the digital twin technology or some surreal parallel experimental methods will perhaps be easily seen in the research of HICEs.

Acknowledgments

This research was supported by the special support plan for high-level talents of Henan Province-“ZHONGYUAN Thousand Talent Program” (ZYQR201810075), the Foreign Expert Project of Ministry of Science and Technology of the People’s Republic of China (G2022026016L), the Plan for Scientific Innovation Talent of Henan Province (154200510020), the National Nature Science Foundation of China (51076046), and the Fund of Innovative Education Program for Ph.D. Graduate Students with North China University of Water Resources and Electric Power (NCWUBC202220).

Glossary

Nomenclature

λ

excessive air ratio

Φ

equivalence ratio

θig

ignition advance angle

ηet

brake thermal efficiency

Tmax

maximum combustion temperature

Pmax

maximum combustion pressure

HICE

hydrogen-fueled internal combustion engine

Biographies

Lijun Wang received a B.S. degree from the North University of China, Taiyuan, China, in 1993, an M.S. degree from Henan Agricultural University, Zhengzhou, China, in 2003, and a Ph.D. degree from PLA Information Engineering University, Zhengzhou, in 2010. Since 2010, she has been a Professor with the School of Mechanical Engineering, North China University of Water Resources and Electric Power, Zhengzhou, where she is currently the Dean of the School of Mechanical Engineering and the Director of the Zhengzhou Key Laboratory of Measurement and Control Technology and Instrument. She has led approximately 20 important scientific research projects. She has authored over 60 scientific articles in international journals and conferences. Her current research interests include signal processing, image processing and machine learning, fault diagnosis, and intelligent control.

Xiangyang Li received a B.S. degree in automotive engineering from Henan Polytechnic University, Henan, China, in 2019. He is now an M.D.-Ph.D. student at North China University of Water Resources and Electric Power, Zhengzhou, China. His current research interests include digital twin and PHM of complex equipment, for example, fuel cells, engines, and others.

Chen Hong received a B.S. degree in mechanical engineering from the North China University of Water Resources and Electric Power, Zhengzhou, China, in 2016, and received an M.S. degree with the School of Mechanical Engineering, in 2020. During his studies, he mainly focused on the operating mechanism of hydrogen internal combustion engines.

Ping Guo received her master’s degree from Baicheng Normal University in Jilin Province in 2021. At present, she is studying at the School of Machinery, North China University of Water Resources and Electric Power, for a master’s degree in Mechanical Master of Engineering, focusing on the optimal control of hydrogen engines.

Shuman Guo graduated from the State Key Laboratory of Internal Combustion Engine of Tianjin University and is mainly engaged in the research of electronic control and energy-saving emission control technology of the internal combustion engine, the control technology of new energy vehicles, and the control and artificial intelligence application technology of driverless vehicles.

Zhenzhong Yang is a professor and doctoral supervisor, with a Ph.D. in Engineering from Zhejiang University, followed by postdoctoral research at Zhejiang University and the National Aerospace Laboratory of Japan. He was once a Visiting scholar at West Virginia University. He has taken the lead in carrying out research work on the combustion and optimal control of hydrogen fuel engines in China for nearly 20 years. He has extensive academic influence in this field and was nominated for the Egyptian Prize.

The authors declare no competing financial interest.

References

  1. Wang L.; Li X.; Guo P.; Guo S.; Yang Z.; Pei P. Bibliometric analysis of prognostics and health management (PHM) in hydrogen fuel cell engines. Int. J. Hydrog. Energy 2022, 47 (80), 34216–34243. 10.1016/j.ijhydene.2022.08.024. [DOI] [Google Scholar]
  2. Onorati A.; Payri R.; Vaglieco B. M.; Agarwal A. K.; Bae C.; Bruneaux G.; Canakci M.; Gavaises M.; Gunthner M.; Hasse C.; Kokjohn S.; Kong S. C.; Moriyoshi Y.; Novella R.; Pesyridis A.; Reitz R.; Ryan T.; Wagner R.; Zhao H. The role of hydrogen for future internal combustion engines. International Journal of Engine Research 2022, 23 (4), 529–540. 10.1177/14680874221081947. [DOI] [Google Scholar]
  3. Masuk N. I.; Mostakim K.; Kanka S. D. Performance and Emission Characteristic Analysis of a Gasoline Engine Utilizing Different Types of Alternative Fuels: A Comprehensive Review. Energy Fuels 2021, 35 (6), 4644–4669. 10.1021/acs.energyfuels.0c04112. [DOI] [Google Scholar]
  4. Yang Z.Combustion and Optimizing Control in a Hydrogen-Fueled Engine (in Chinese); Zhejiang University: Hangzhou, China, 2001. [Google Scholar]
  5. Gao J.; Wang X.; Song P.; Tian G.; Ma C. Review of the backfire occurrences and control strategies for port hydrogen injection internal combustion engines. Fuel 2022, 307, 121553. 10.1016/j.fuel.2021.121553. [DOI] [Google Scholar]
  6. Wang L.; Hong C.; Li X.; Yang Z.; Guo S.; Li Q. Review on blended hydrogen-fuel internal combustion engines: A case study for China. Energy Rep. 2022, 8, 6480–6498. 10.1016/j.egyr.2022.04.079. [DOI] [Google Scholar]
  7. Jervis-Smith F. J. Cecil’s Gas Engine. Nature 1904, 70 (1823), 553–553. 10.1038/070553b0. [DOI] [Google Scholar]
  8. Namar M. m.; Jahanian O. Energy and exergy analysis of a hydrogen-fueled HCCI engine. J. Therm. Anal. Calorim. 2019, 137 (1), 205–215. 10.1007/s10973-018-7910-7. [DOI] [Google Scholar]
  9. Yang Z.; Du Y.; Geng Q.; He G. Energy loss and comprehensive performance analysis of a novel high-efficiency hybrid cycle hydrogen-gasoline rotary engine under off-design conditions. Energy Conv. Manag. 2022, 267, 115942. 10.1016/j.enconman.2022.115942. [DOI] [Google Scholar]
  10. Perini F.; Paltrinieri F.; Mattarelli E. A quasi-dimensional combustion model for performance and emissions of SI engines running on hydrogen-methane blends. Int. J. Hydrog. Energy 2010, 35 (10), 4687–4701. 10.1016/j.ijhydene.2010.02.083. [DOI] [Google Scholar]
  11. Rao A.; Gao H.; Ma F. Study of laminar burning speed and calibration coefficients of quasi-dimensional combustion model for hydrogen enriched compressed natural gas fueled internal combustion engine along with exhaust gas recirculation. Fuel 2021, 283, 119284. 10.1016/j.fuel.2020.119284. [DOI] [Google Scholar]
  12. Addepalli S. K.; Pei Y.; Zhang Y.; Scarcelli R. Multi-dimensional modeling of mixture preparation in a direct injection engine fueled with gaseous hydrogen. Int. J. Hydrog. Energy 2022, 47 (67), 29085–29101. 10.1016/j.ijhydene.2022.06.182. [DOI] [Google Scholar]
  13. Cameretti M. C.; De Robbio R.; Mancaruso E.; Palomba M. CFD Study of Dual Fuel Combustion in a Research Diesel Engine Fueled by Hydrogen. Energies 2022, 15 (15), 5521. 10.3390/en15155521. [DOI] [Google Scholar]
  14. Li j.; Zhou Q.; He X.; Chen W.; Xu H. Data-driven enabling technologies in soft sensors of modern internal combustion engines: Perspectives. Energy 2023, 272, 127067. 10.1016/j.energy.2023.127067. [DOI] [Google Scholar]
  15. Soderang E.; Hautala S.; Mikulski M.; Storm X.; Niemi S. Development of a digital twin for real-time simulation of a combustion engine-based power plant with battery storage and grid coupling. Energy Conv. Manag. 2022, 266, 115793. 10.1016/j.enconman.2022.115793. [DOI] [Google Scholar]
  16. Frasci E.; Sementa P.; Arsie I.; Jannelli E.; Vaglieco B. M. Experimental and numerical investigation of the impact of the pure hydrogen fueling on fuel consumption and NOx emissions in a small DI SI engine. International Journal of Engine Research 2023, 24, 3574. 10.1177/14680874231162141. [DOI] [Google Scholar]
  17. Babayev R.; Andersson A.; Serra Dalmau A.; Im H. G.; Johansson B. Computational comparison of the conventional diesel and hydrogen direct-injection compression-ignition combustion engines. Fuel 2022, 307, 121909. 10.1016/j.fuel.2021.121909. [DOI] [Google Scholar]
  18. Nguyen D.; Kar T.; Turner J. W. G. Performance, Emissions, and Combustion Characteristics of a Hydrogen-Fueled Spark-Ignited Engine at Different Compression Ratios: Experimental and Numerical Investigation. Energies 2023, 16 (15), 5730. 10.3390/en16155730. [DOI] [Google Scholar]
  19. Karagoz Y.; Yuca N.; Sandalci T.; Dalkilic A. S. Effect of hydrogen and oxygen addition as a mixture on emissions and performance characteristics of a gasoline engine. Int. J. Hydrog. Energy 2015, 40 (28), 8750–8760. 10.1016/j.ijhydene.2015.05.039. [DOI] [Google Scholar]
  20. Pal A.; Agarwal A. K. Comparative study of laser ignition and conventional electrical spark ignition systems in a hydrogen fuelled engine. Int. J. Hydrog. Energy 2015, 40 (5), 2386–2395. 10.1016/j.ijhydene.2014.12.030. [DOI] [Google Scholar]
  21. Salavati-Zadeh A. l.; Javaheri A.; Ghavami S. V.; Esfahanian V.; Tehrani M. M.; Akbari H. A detailed kinetic investigation on the effects of hydrogen enrichment on the performance of gas-fueled SI engine. Int. J. Green Energy 2016, 13 (10), 1042–1049. 10.1080/15435075.2016.1206007. [DOI] [Google Scholar]
  22. Wrobel K.; Wrobel J.; Tokarz W.; Lach J.; Podsadni K.; Czerwinski A. Hydrogen Internal Combustion Engine Vehicles: A Review. Energies 2022, 15 (23), 8937. 10.3390/en15238937. [DOI] [Google Scholar]
  23. Li J.; Guo L.; Chu S.; Sun X.; Furuhama S. Study on hydrogen as a substitute fuel for engines. Trans. CSAE 1996, 12, 86e91. [Google Scholar]
  24. Yang Z.; Duan J.; Lian Z.; Song M. Research on cyclic variation and influencing factors of hydrogen engine (In Chinese). Vehicle Engine 2010, 46–49. [Google Scholar]
  25. Wang S.; Ji C.; Zhang Q.; Zhang J.; Jiu Z.; Fan B. Combustion and cycle-by-cycle variation of pure hydrogen-fueled spark ignition engine at idle and lean conditions (In Chinese). Trans. Chinese Soc. Agric. Machinery 2011, 42, 12–15. [Google Scholar]
  26. Ma F.; Liu H.; Li Y.; Wang Y.; Zhao S. Analysis of in-cylinder combustion of hydrogen fueled engine (In Chinese). Internal Combustion Engine Eng. 2008, 29, 29–33. [Google Scholar]
  27. Song Z. Y.Design and research of system of real-time simulated hydrogen engine. Dissertation/Thesis; Beijing Institute of Technology, Beijing, China, 2010. [Google Scholar]
  28. Ma F.; He Y.; Deng J.; Jiang L.; Naeve N.; Wang M.; Chen R. Idle characteristics of a hydrogen fueled SI engine. Int. J. Hydrog. Energy 2011, 36 (7), 4454–4460. 10.1016/j.ijhydene.2010.12.121. [DOI] [Google Scholar]
  29. He Y.; Ma F.; Deng J.; Nashay N. Idle characteristics of a hydrogen fueled SI engine (In Chinese). J. Beijing Univ. Technol. 2012, 38, 1560–1564. [Google Scholar]
  30. Zhao Z.; Sun B.; Lu F.; Zhao J.; Fan Z. Experimental study on ignition energy of hydrogen internal combustion engine. Vehicle Engine 2009, 69–71. [Google Scholar]
  31. Luo Q.; Sun B. Experiments on the effect of engine speed, load, equivalence ratio, spark timing and coolant temperature on the energy balance of a turbocharged hydrogen engine. Energy Conv. Manag. 2018, 162, 1–12. 10.1016/j.enconman.2017.12.051. [DOI] [Google Scholar]
  32. Wang X.; Sun B.; Luo Q. Energy and exergy analysis of a turbocharged hydrogen internal combustion engine. Int. J. Hydrog. Energy 2019, 44 (11), 5551–5563. 10.1016/j.ijhydene.2018.10.047. [DOI] [Google Scholar]
  33. Luo Q.; Sun B.; Tian H. The characteristic of polytropic coefficient of compression stroke in hydrogen internal combustion engine. Int. J. Hydrog. Energy 2014, 39 (25), 13787–13792. 10.1016/j.ijhydene.2014.04.035. [DOI] [Google Scholar]
  34. Luo Q.; Sun B. Effect of the Miller cycle on the performance of turbocharged hydrogen internal combustion engines. Energy Conversion Management 2016, 123, 209–217. 10.1016/j.enconman.2016.06.039. [DOI] [Google Scholar]
  35. Sun B.; Xiang Q.; Liu F. The study on the performance of hydrogen internal combustion engine and vehicle (In Chinese). Trans. Beijing InstituteTechnol. 2012, 32, 1026–1030. [Google Scholar]
  36. Ma J.; Su Y.; Zhou Y.; Zhang Z. Simulation and prediction on the performance of a vehicle’s hydrogen engine. Int. J. Hydrog. Energy 2003, 28 (1), 77–83. 10.1016/S0360-3199(02)00046-0. [DOI] [Google Scholar]
  37. Yang Z.; Shun Y. Modeling for hydrogen fueled engine performance based on radial basis function network (In Chinese). Acta Energiae Solaris Sinica 2007, 28, 557. [Google Scholar]
  38. Sun D.; Liu F.; Sun B.; Zhou L. Experimental study on performance and emission of hydrogen internal combustion engine using hot EGR (In Chinese). Trans. Chinese Soc. Internal Combustion Engines 2009, 27, 134–139. [Google Scholar]
  39. Duan J.; Liu F.; Sun B. Performance and emissions of hydrogen internal combustion engine with hot EGR (In Chinese). Internal Combustion Engine Engineering 2016, 37, 21–25. [Google Scholar]
  40. Sun B.; Meng F.; Liu F. Hydrogen internal combustion engine turbo charging matching and parameters optimization for high power density (In Chinese). Trans. Beijing Institute Technol. 2013, 33, 1130–1134. [Google Scholar]
  41. Su T.; Ji C.; Wang S.; Shi L.; Yang J.; Cong X. Idle performance of a hydrogen rotary engine at different excess air ratios. Int. J. Hydrogen Energy 2018, 43 (4), 2443–2451. 10.1016/j.ijhydene.2017.12.028. [DOI] [Google Scholar]
  42. Meng H.; Ji C.; Yang J.; Chang K.; Xin G.; Wang S. Experimental understanding of the relationship between combustion/flow/flame velocity and knock in a hydrogen-fueled Wankel rotary engine. Energy 2022, 258, 124828 10.1016/j.energy.2022.124828. [DOI] [Google Scholar]
  43. Yuan C.; Han C.; Xu J. Numerical evaluation of pilot-ignition technology used for a hydrogen fuelled free piston engine generator. Int. J. Hydrog. Energy 2017, 42 (47), 28599–28611. 10.1016/j.ijhydene.2017.09.131. [DOI] [Google Scholar]
  44. Yuan C.; Jing Y.; Liu C.; He Y. Effect of variable stroke on fuel combustion and heat release of a free piston linear hydrogen engine. Int. J. Hydrog. Energy 2019, 44 (36), 20416–20425. 10.1016/j.ijhydene.2019.05.232. [DOI] [Google Scholar]
  45. Yuan C.; Ren H.; Jing Y.; Xu J.; He Y. The effect of motion on fuel diffusion and mixture preparation of a free-piston linear hydrogen engine. Int. J. Hydrog. Energy 2019, 44 (10), 4996–5006. 10.1016/j.ijhydene.2018.12.197. [DOI] [Google Scholar]
  46. Cao R.; Chang J.; Bao W.; Guo M.; Qin J.; Yu D.; Wang Z. Analysis of combustion mode and operating route for hydrogen fueled scramjet engine. Int. J. Hydrog. Energy 2013, 38 (14), 5928–5935. 10.1016/j.ijhydene.2013.02.135. [DOI] [Google Scholar]
  47. Yang Q.; Chang J.; Bao W.; Deng J. A mechanism of combustion mode transition for hydrogen fueled scramjet. Int. J. Hydrog. Energy 2014, 39 (18), 9791–9797. 10.1016/j.ijhydene.2014.04.090. [DOI] [Google Scholar]
  48. Zhang C.; Qin J.; Yang Q.; Zhang S.; Bao W. Design and heat transfer characteristics analysis of combined active and passive thermal protection system for hydrogen fueled scramjet. Int. J. Hydrog. Energy 2015, 40 (1), 675–682. 10.1016/j.ijhydene.2014.11.036. [DOI] [Google Scholar]
  49. Yang Q.; Zong Y.; Bao W. Constant static-temperature heating for hydrogen fueled scramjet engine. Int. J. Hydrog. Energy 2016, 41 (3), 2002–2010. 10.1016/j.ijhydene.2015.11.014. [DOI] [Google Scholar]
  50. Yang Z.; Liu H.; Tian G.; Wang L.; Si A.; Pei P. Research on Abnormal Combustion of Hydrogen-Fueled Engine Using Wavelet Transform. Acta Energiae Solaris Sinica 2008, 29, 700–704. [Google Scholar]
  51. Yang Z.; Shi S.; Song M. Analysis and control of abnormal combustion of hydrogen fueled engines based on pressure rise rate. Trans. Chinese Soc. Agric. Eng. 2010, 26, 124–129. [Google Scholar]
  52. Zhenzhong Y.; Lijun W.; Manlou H.; Yongdi C. Research on optimal control to resolve the contradictions between restricting abnormal combustion and improving power output in hydrogen fueled engines. Int. J. Hydrogen Energy 2012, 37, 774–782. 10.1016/j.ijhydene.2011.04.062. [DOI] [Google Scholar]
  53. Yang Z.; Wang L.; Zhang Q.; Meng Y.; Pei P. Research on optimum method to eliminate backfire of hydrogen internal combustion engines based on combining postponing ignition timing with water injection of intake manifold. Int. J. Hydrog. Energy 2012, 37 (17), 12868–12878. 10.1016/j.ijhydene.2012.05.082. [DOI] [Google Scholar]
  54. Duan J.; Liu F.; Sun B. Backfire mechanism and control of PFI hydrogen internal combustion engine (In Chinese). Nongye Jixie Xuebao 2013, 44, 1–5. [Google Scholar]
  55. Gao Y.; Yang Z.; Guo S.; Qin C.; Cheng W.; Zhang W. Influence of intake port on mixture formation in hydrogen engine (In Chinese).. Internal Combustion 2014, 35, 106–111. [Google Scholar]
  56. Liu X.; Liang H.; Liu F.; Sun D.; Sun B.; Sun Z.; Zhang C. A research on the backfire in a port injection hydrogen engine (In Chinese). Automotive Eng. 2014, 36, 653–656. [Google Scholar]
  57. Luo Q.; Sun B. Inducing factors and frequency of combustion knock in hydrogen internal combustion engines. Int. J. Hydrog. Energy 2016, 41 (36), 16296–16305. 10.1016/j.ijhydene.2016.05.257. [DOI] [Google Scholar]
  58. Qing C.; Yang Z.; Zhang W.; Song L.; Yuan Y. A study on low-temperature combustion characteristics in hydrogen engine (In Chinese). Automotive Eng. 2017, 39, 133–137. [Google Scholar]
  59. Yang Z.; Li D.; Wang L. Research on the hot surface ignition of hydrogen-air mixture under different influencing factors. International Journal of Energy Research 2018, 42 (12), 3966–3976. 10.1002/er.4132. [DOI] [Google Scholar]
  60. Yang Z.; Wu J.; Yun H.; Zhang H.; Xu J. Diagnosis and control of abnormal combustion of hydrogen internal combustion engine based on the hydrogen injection parameters. Int. J. Hydrog. Energy 2022, 47 (35), 15887–15895. 10.1016/j.ijhydene.2022.03.031. [DOI] [Google Scholar]
  61. Dang J.; Wang L. Research on diagnosis of pre-ignition of hydrogen engine based on SOM-MAS. Int. J. Hydrog. Energy 2022, 47 (82), 35112–35121. 10.1016/j.ijhydene.2022.08.107. [DOI] [Google Scholar]
  62. Liu X.; Liu F.; Zhou L.; Sun B.; Schock H. J. Backfire prediction in a manifold injection hydrogen internal combustion engine. Int. J. Hydrog. Energy 2008, 33 (14), 3847–3855. 10.1016/j.ijhydene.2008.04.051. [DOI] [Google Scholar]
  63. Sun B.; Zhang D.; Liu F. Investigation of the characteristics of hydrogen injector using experiment and simulation in hydrogen internal combustion engine. Int. J. Hydrog. Energy 2012, 37 (17), 13118–13124. 10.1016/j.ijhydene.2012.03.169. [DOI] [Google Scholar]
  64. Sun B.; Zhang D.; Liu F. Pressure fluctuations in a hydrogen supply system during hydrogen injection. Int. J. Hydrog. Energy 2013, 38 (25), 11156–11163. 10.1016/j.ijhydene.2013.02.122. [DOI] [Google Scholar]
  65. Duan J.; Liu F.; Sun B. Hydrogen-air mixture characteristics of PFI hydrogen internal combustion engine (In Chinese). Vehicle Engine 2014, 29–32. [Google Scholar]
  66. Duan J.; Liu F.; Sun B. Backfire control and power enhancement of a hydrogen internal combustion engine. Int. J. Hydrog. Energy 2014, 39 (9), 4581–4589. 10.1016/j.ijhydene.2013.12.175. [DOI] [Google Scholar]
  67. Yang Z.; Zhang F.; Wang L.; Wang K.; Zhang D. Effects of injection mode on the mixture formation and combustion performance of the hydrogen internal combustion engine. Energy 2018, 147, 715–728. 10.1016/j.energy.2018.01.068. [DOI] [Google Scholar]
  68. Xu J.Effect of Hydrogen Injection Strategy and Valve Timing on Hydrogen Engine Performance (in Chinese); North China University of Water Resources and Electric Power: Zhengzhou, China, 2022. [Google Scholar]
  69. Yang Y.Effects of Spray Hole Distribution and Injection Timing on Formation Process of Mixed Gas in a Hydrogen Internal Combustion Engine (in Chinese); North China University of Water Resources and Electric Power: Zhengzhou, China, 2015. [Google Scholar]
  70. Huang Y.Effects of Injection Timing and Injection Position on Mixture and Combustion Characteristics of a PFI Hydrogen Internal Combustion Engine (in Chinese): North China University of Water Resources and Electric Power: Zhengzhou, China, 2015. [Google Scholar]
  71. Wu M.Effect of Injection Area and Injection Pressure on Mixture and Combustion Characteristics of a PFI Hydrogen Internal Combustion Engine (in Chinese); North China University of Water Resources and Electric Power: Zhengzhou, China, 2016. [Google Scholar]
  72. Zhang D.Comparative Study on Symmetrical and Spaced Injection Mode of Hydrogen Internal Combustion Engine (in Chinese); North China University of Water Resources and Electric Power: Zhengzhou, China, 2018. [Google Scholar]
  73. Wang K.Effects of Single Pipe Multiple Injection and Spaced Dual Injection on the Performance of Hydrogen Engine (in Chinese); North China University of Water Resources and Electric Power: Zhengzhou, China, 2018. [Google Scholar]
  74. Zhenzhong Y.; Aiguo S.; Fei W.; Nan G. Research into the formation process of hydrogen–air mixture in hydrogen fueled engines based on CFD. Int. J. Hydrogen Energy 2010, 35, 3051–3057. 10.1016/j.ijhydene.2009.07.042. [DOI] [Google Scholar]
  75. Wang C.; Liu F. Mixture distribution and ignition position in hydrogen direct-injection spark-ignited engine (In Chinese). Transa. CSICE 2010, 28, 519–524. [Google Scholar]
  76. Sun B.; Zhang D.; Liu F. Evaluation method on cycle variations of hydrogen internal combustion engine (In Chinese). Trans. CSICE 2013, 31, 133–138. [Google Scholar]
  77. Sun B.; Zhang D.; Liu F. Cycle variations in a hydrogen internal combustion engine. Int. J. Hydrog. Energy 2013, 38 (9), 3778–3783. 10.1016/j.ijhydene.2012.12.126. [DOI] [Google Scholar]
  78. Sun B.; Zhang D.; Liu F. Cycle variations internal combustion engine (In Chinese). J. Combust. Sci. Technol. 2013, 19, 311–316. [Google Scholar]
  79. Xu P.; Ji C.; Wang S.; Bai X.; Cong X.; Su T.; Shi L. Realizing low NOx emissions on a hydrogen-fuel spark ignition engine at the cold start period through excess air ratios control. Int. J. Hydrog. Energy 2018, 43 (46), 21617–21626. 10.1016/j.ijhydene.2018.09.136. [DOI] [Google Scholar]
  80. Xu P.; Ji C.; Wang S.; Bai X.; Cong X.; Su T.; Shi L. Realizing low emissions on a hydrogen-fueled spark ignition engine at the cold start period under rich combustion through ignition timing control. Int. J. Hydrogen Energy 2019, 44 (16), 8650–8658. 10.1016/j.ijhydene.2019.01.275. [DOI] [Google Scholar]
  81. Bai X.Research on Cold Start Combustion and Emission Characteristics of Hydrogen Internal Combustion Engine; Beijing University of Technology: Beijing, China, 2019. [Google Scholar]
  82. Liu D. Experimental study on the start performance and emission of hydrogen internal combustion engine (In Chinese). J. Agricultural Mechanization Res. 2012, 34, 241–244. [Google Scholar]
  83. Wang S.; Zhai Y.; Wang Z.; Hou R.; Zhang T.; Ji C. Comparison of air and EGR with different water fractions dilutions on the combustion of hydrogen-air mixtures. Fuel 2022, 324, 124686 10.1016/j.fuel.2022.124686. [DOI] [Google Scholar]
  84. Li D.; Du Y.; Yu X. Simulation of Inner-Engine NOx Emission Control on Pure Hydrogen Engines. Journal of Tongji University (Natural Science Edition) 2021, 049. [Google Scholar]
  85. Duan J.; Liu F.; Yang Z.; Sun B.; Chen W.; Wang L. Study on the NOx emissions mechanism of an HICE under high load. Int. J. Hydrogen Energy 2017, 42, 22027–22035. 10.1016/j.ijhydene.2017.07.048. [DOI] [Google Scholar]
  86. Zhu H.; Duan J. Research on emission characteristics of hydrogen fuel internal combustion engine based on more detailed mechanism. Int. J. Hydrog. Energy 2019, 44 (11), 5592–5598. 10.1016/j.ijhydene.2018.08.044. [DOI] [Google Scholar]
  87. Duan J.; Wu P.; Zhu H.; Qin G.; Wei W. Simplification and applicability studies of a hydrogen-air detailed reaction mechanism. Int. J. Hydrog. Energy 2019, 44 (11), 5538–5542. 10.1016/j.ijhydene.2018.09.173. [DOI] [Google Scholar]
  88. Luo Q.; Hu J.; Sun B.; Liu F.; Wang X.; Li C.; Bao L. Effect of equivalence ratios on the power, combustion stability and NOx controlling strategy for the turbocharged hydrogen engine at low engine speeds. Int. J. Hydrog. Energy 2019, 44 (31), 17095–17102. 10.1016/j.ijhydene.2019.03.245. [DOI] [Google Scholar]
  89. Luo Q.; Hu J.; Sun B.; Liu F.; Wang X.; Li C.; Bao L. Experimental investigation of combustion characteristics and NOx emission of a turbocharged hydrogen internal combustion engine. Int. J. Hydrog. Energy 2019, 44 (11), 5573–5584. 10.1016/j.ijhydene.2018.08.184. [DOI] [Google Scholar]
  90. Sun B.; Zhao J.; Zhao L.; Liu F.; Hu T.; Yang B. Experimental study on NOx emission of hydrogen internal combustion engine (In Chinese). Internal Combustion Engine Engineering 2011, 32, 53–56. [Google Scholar]
  91. Duan J.; Liu F.; Sun B. An experimental study on the NOx emission characteristics of PFI hydrogen internal combustion engine (In Chinese). Automotive Engineering 2014, 36, 1175–1179. [Google Scholar]
  92. Zhenzhong Y.; Jianqin W.; Zhuoyi F.; Jinding L. An investigation of optimum control of ignition timing and injection system in an in-cylinder injection type hydrogen fueled engine. Int. J. Hydrogen Energy 2002, 27, 213–217. 10.1016/S0360-3199(01)00096-9. [DOI] [Google Scholar]
  93. Yang Z.; Xiong S.; Li J. Performances of a hydrogen-fueled engine in different ignition timing and its optimizing control with fuzzy-neural network. Acta Energiae Solaris Sinica 2003, 24, 522–525. [Google Scholar]
  94. Yang Z.; Li J.; Yan D. The optimal control model of hydrogen fueled engines based on fuzzy neural network(In Chinese). Automotive Engineering 2003, 25, 444–446. [Google Scholar]
  95. Yang Z.; Wang L.; Li S. Investigation into the optimization control technique of hydrogen-fueled engines based on genetic algorithms. Int. J. Hydrog. Energy 2008, 33 (22), 6780–6791. 10.1016/j.ijhydene.2008.05.108. [DOI] [Google Scholar]
  96. Yang Z.; Wang L.; Li S.; Pei P. Study on Optimum Control of Hydrogen Fueled Engine Based on Genetic Algorithms. Trans. CSICE 2008, 26, 62–68. [Google Scholar]
  97. Wang L.; He M.; Yang Z. Research on optimal calibration technology for hydrogen-fueled engine based on nonlinear programming theory. Int. J. Hydrog. Energy 2010, 35 (7), 2747–2753. 10.1016/j.ijhydene.2009.04.074. [DOI] [Google Scholar]
  98. Wang L.; Yang Z.; He M. Research on optimizing control model of hydrogen fueled engines based on thermodynamics and state space analysis method about nonlinear system. Int. J. Hydrog. Energy 2012, 37 (12), 9902–9913. 10.1016/j.ijhydene.2012.03.082. [DOI] [Google Scholar]
  99. Wang L.; Liu Y.; Liu Y.; Wang W.; Zhao Y.; Yang Z. Optimization of Hydrogen-fueled Engine Ignition Timing Based on LM Neural Network Algorithm. TELKOMNIKA 2016, 14 (3), 923–932. 10.12928/telkomnika.v14i3.2756. [DOI] [Google Scholar]
  100. Wang L.; Zhao Y.; Dang J.; Yang Z. Performance Optimization of Hydrogen Fueled Engines Based on Genetic Information Fusion Algorithm. Chem. Eng. Trans. 2017, 62, 607–612. [Google Scholar]
  101. Yun H.; Bu Z.; Yang Z.; Wang L.; Zhang B. Optimization of fuel injection timing and ignition timing of hydrogen fueled SI engine based on DOE-MPGA. Int. J. Hydrog. Energy 2023, 48 (25), 9462–9473. 10.1016/j.ijhydene.2022.12.068. [DOI] [Google Scholar]

Articles from ACS Omega are provided here courtesy of American Chemical Society

RESOURCES