Abstract
The design of effective ultrafiltration/diafiltration processes for protein formulation requires the use of membranes with very high protein retention. The objective of this study was to examine the effects of specific buffers on the retention of a model protein (bovine serum albumin) during ultrafiltration. Albumin retention at pH 4.8 was significantly reduced in phosphate buffer compared with that in acetate, citrate, and histidine. This behavior was consistent with a small change in the effective albumin hydrodynamic diameter as determined by dynamic light scattering. The underlying conformational changes leading to this change in diameter were explored using circular dichroism spectroscopy and differential scanning calorimetry. These results provide important insights into the factors controlling protein retention during ultrafiltration and diafiltration.
Keywords: buffer, diafiltration, formulation, protein, sieving, ultrafiltration
1. INTRODUCTION
Ultrafiltration and diafiltration (UFDF) are used to achieve final concentration and buffer exchange during the formulation of almost all therapeutic proteins. One of the critical issues in the design of the UFDF step is maintaining very high yield of the retained product. As discussed by van Reis et al. 1 yield losses can occur by four distinct mechanisms:
Sieving (retention) losses, that is, loss of product due to transmission through the membrane and into the permeate solution,
Adsorption to the membrane, which also includes capture of the product on or within the membrane pores,
Unrecoverable hold‐up volume within the membrane module and system piping, and
Product quality losses, either due to gel formation in the highly concentrated boundary layer or to protein aggregation/denaturation caused by shear stress associated with the pumps and/or flow through the module.
There have been significant efforts to address all these challenges. Very hydrophilic composite regenerated cellulose membranes have been developed with low protein adsorption. 2 Rao et al. 3 have examined strategies for enhancing product recovery and reducing hold‐up volume losses. Arunkumar et al. 4 have examined the effect of spacer geometry on shear‐induced aggregation of monoclonal antibodies and a fusion protein.
Protein sieving losses during UFDF processes are directly related to the magnitude of the protein sieving coefficient (S o), the ratio of the protein concentration in the permeate to that in the feed, with the protein yield for a process with constant So given as: 5
| (1) |
where VCF is the volume concentration factor (ratio of initial to final volume during the ultrafiltration step) and N D is the number of diavolumes (equal to the ratio of the diafiltration buffer volume to the feed volume during the constant volume diafiltration). A membrane with 99% protein retention (S o = 0.01) will have only an 88.4% protein yield for a UFDF process with VCF = 10 and N D = 10 (both typical of commercial UFDF operations). 6 A UFDF process with <2% loss in the permeate would require S o < 0.0016.
The typical rule of thumb in choosing membranes for UFDF applications is to select a membrane with a nominal molecular weight cutoff (MWCO) that is 20%–33% of the molecular weight of the protein product. 7 This guideline is consistent with data for an anti‐CD11a monoclonal antibody (MW = 150 kDa), which showed sieving coefficients of S o = 0.015 and 0.00028 for 100 and 30 kDa MWCO composite regenerated cellulose membranes, respectively. 8 However, data with fluorescently labeled dextrans have shown that membranes with a 300 kDa MWCO can permit transmission of solutes with MW > 2000 kDa. 9 A number of investigators have shown that charge‐modified membranes can reduce the sieving coefficients of like‐charged proteins, 8 , 10 but none of these are commercially available. Although it is almost always possible to choose a membrane with sufficiently low MWCO to achieve the desired protein retention, these “tight” membranes will have very low filtrate flux leading to long processing times and/or large membrane area requirements, which will increase overall manufacturing costs and yield losses (due to protein adsorption and unrecoverable hold‐up volume).
The objective of this study is to examine the effects of different buffers on protein retention during ultrafiltration using bovine serum albumin (BSA) as a model protein due to the extensive previous work on BSA ultrafiltration. Although previous studies have demonstrated that BSA retention during UF can be strongly influenced by solution pH, 11 ionic strength, 12 , 13 and ion binding, 14 , 15 the impact of specific buffer species on the ultrafiltration behavior has not yet been examined quantitatively. It is well known that different buffer species can affect protein conformational stability and in turn enzymatic activity, heat of ionization, and thermal stability 16 as well as thermally induced aggregation. 17 Therefore, we used dynamic light scattering (DLS), differential scanning calorimetry (DSC), and circular dichroism (CD) to identify possible conformational changes that may have affected the ultrafiltration behavior. The results provide important insights into the underlying factors controlling sieving losses during UFDF processes.
2. MATERIALS AND METHODS
Bovine serum albumin with MW of 67 kDa and isoelectric point of 4.8 was obtained as a lyophilized powder from MilliporeSigma (Product Number A7906, St. Louis, MO). BSA powder was dissolved in the appropriate buffers with sodium phosphate, sodium acetate anhydrous, and citric acid anhydrous obtained from DOT Scientific (Burton, MI) while L‐Histidine was from MilliporeSigma (Burlington, MA). The pH was adjusted using concentrated base or acid as needed; these adjustments were very small and had no measurable effect on the solution ionic strength. The resulting BSA solutions were filtered through 0.22 μm pore size polyethersulfone filters (MilliporeSigma, Burlington, MA) to remove any aggregates or undissolved species before use. The prefiltered BSA solutions were kept at 4°C (for a maximum of 2 days) and were returned to room temperature (21 ± 2°C) prior to filtration or characterization.
BSA concentrations were evaluated from the UV absorbance at 280 nm determined using a Tecan Infinite 200 PRO spectrophotometer. Samples were diluted as needed to remain in the linear portion of the calibration curve (concentrations <1 g/L).
2.1. Protein filtration
Ultrafiltration experiments were performed using both polyethersulfone and regenerated cellulose ultrafiltration membranes with 30 kDa MWCO as summarized in Table 1. These 30 kDa membranes have a somewhat larger MWCO than would likely be used for BSA ultrafiltration; this provided slightly higher protein transmission, significantly increasing the accuracy of the sieving coefficient data. Membranes were provided either as small circular disks or pre‐sealed in tangential flow filtration modules. The membranes were rinsed with Milli‐Q water prior to use to remove any storage/wetting agents following the manufacturer's protocol.
TABLE 1.
Membranes used in ultrafiltration experiments.
| Polymer | Supplier | Format | |
|---|---|---|---|
| Biomax | PES | MilliporeSigma | TFF |
| Omega | PES | Pall/Cytiva | Disk |
| Ultracel | Cellulose | MilliporeSigma | TFF |
Membrane disks were placed at the base of a 25 mm diameter Amicon stirred ultrafiltration cell (Model 8010, MilliporeSigma) fed by a 1 L solution reservoir. The reservoir was initially filled with DI water, with the membrane permeability:
| (2) |
evaluated from data for the filtrate flux (J v) as a function of the transmembrane pressure (TMP). The filtrate flux was evaluated by timed collection while the TMP was controlled and monitored using a pressure regulator (Ashcroft, Stratford, CT). The system was then emptied, with the stirred cell refilled with the BSA solution while the reservoir was filled with protein‐free buffer (the same buffer as that used to dissolve the BSA). The buffer feed made it possible to maintain nearly constant protein concentration in the stirred cell even after collection of a significant volume of filtrate due to the high degree of protein retention in all experiments. The stirrer was set to 800 rpm and the system repressurized, with permeate samples obtained periodically to evaluate both the filtrate flux and the BSA concentration.
Tangential flow filtration (TFF) was performed using the 30 kDa Biomax and Ultracel membranes in Pellicon 3 cassettes with C screen (MilliporeSigma) having 88 cm2 membrane area. The membrane permeability was again measured with DI water, with the system then flushed with approximately 40 L/m2 of protein‐free buffer. The BSA solution was added to a 0.25 L reservoir that was mixed with a magnetic stirrer (providing a loading of 426 g BSA/m2). The feed and permeate flow rates were controlled using separate Masterflex pumps, with the permeate and retentate lines recycled back to the feed reservoir to maintain a constant protein concentration throughout the experiment. Feed and permeate samples were collected periodically to evaluate the protein sieving coefficient.
2.2. Protein characterization
A variety of techniques were used to examine the BSA properties in the different buffers. The effective BSA size was determined by DLS using the Zetasizer Nano (Malvern Instruments, Worcestershire, UK). The scattered light was collected at an angle of 90°, with three repeat scans performed for each sample at room temperature. The effective protein diameter was evaluated from the measured diffusivity (D), determined from the transient decay in the scattering intensity, using the Stokes–Einstein equation:
| (3) |
where T is the absolute temperature, k B is Boltzmann's constant, and η is the solution viscosity (assumed to be equal to that of water at the measured temperature). The protein zeta potential was also determined by the Zetasizer Nano based on measurements of the electrophoretic mobility.
The secondary structure of the protein was examined using a Jasco J‐1500 CD spectrometer with a xenon arc lamp source. Spectra were obtained with 0.25 g/L solutions of BSA, generated by diluting the 15 g/L solutions with the appropriate buffer. Spectra were analyzed using the BESTSEL curve‐fitting program to quantify the alpha‐helix and beta‐sheet content.
DSC was used to evaluate the protein stability in the different buffers. DSC measurements were carried out using a MicroCal VP‐capillary DSC (now Malvern Panalytical). Data were collected over a temperature range from 25 to 105°C with a scan speed of 1.5°C/min. A buffer reference cell was run for baseline correction. Data were obtained at BSA concentrations of 15 g/L, with the data analyzed using LLC Cap DSC Version Origin70‐L3 to evaluate the molar heat capacity (MHC).
3. RESULTS AND ANALYSIS
3.1. Buffer effects
Table 2 summarizes data for the transmission of BSA through the different 30 kDa membranes at a filtrate flux of approximately 11 ± 1 μm/s (40 ± 3 L/m2/h), all at pH 4.8 using 20 mM buffers. Each data point was obtained with a different membrane disk, chosen so that the hydraulic permeabilities were all within ±10% of the mean values (given in Table 1). The error bars represent the standard deviation determined from multiple repeat measurements (typically 3–5 data points). The Omega membranes were used in the stirred cell (at a stirring speed of 800 rpm) while the Biomax and Ultracel membranes were used in TFF modules (at feed fluxes of 410 and 580 L/m2/h, corresponding to feed flow rates of 60 and 85 mL/min, respectively). The highest values of the sieving coefficient for all three membranes were obtained in the phosphate buffer, with nearly identical values for the Omega, Biomax, and Ultracel membranes. The BSA transmission in the other buffers were 2–3‐fold smaller than those obtained in phosphate, with the sieving coefficients in the acetate buffer being somewhat greater than those in either citrate or histidine for both the Omega and Biomax membranes (the S o values for the Ultracel were not determined in acetate and citrate buffers). These trends were reproducible with different membrane disks/cassettes and at both higher and lower filtrate flux. Note that the sieving coefficients for the Omega membrane would correspond to protein yields ranging from 95.7% in the citrate buffer to only 87.3% in the phosphate buffer (only accounting for yield losses in the permeate with the protein yield evaluated from Equation 1 assuming a UFDF process with VCF = 10 and N D = 10).
TABLE 2.
Effective hydrodynamic diameters and BSA sieving coefficients through the different 30 kDa membranes at pH 4.8 in the different buffers.
| Buffer | Hydrodynamic diameter, d (nm) | Transmission, S o | ||
|---|---|---|---|---|
| Omega | Biomax | Ultracel | ||
| Acetate | 7.9 | 0.0047 ± 0.0001 | 0.0056 ± 0.0010 | — |
| Citrate | 7.7 | 0.0036 ± 0.0001 | 0.0033 ± 0.0004 | — |
| Histidine | 7.6 | 0.0037 ± 0.0001 | 0.0025 ± 0.0001 | 0.0022 ± 0.0001 |
| Phosphate | 7.1 | 0.011 ± 0.00006 | 0.011 ± 0.001 | 0.011 ± 0.001 |
The significantly larger BSA transmission in the phosphate buffer was consistent with the protein size distributions determined by DLS as shown in Figure 1. The DLS data show only a single peak, with the distribution in the phosphate buffer shifted to the left (to smaller size) relative to that in the other buffers. The size distributions shown in Figure 1 were used to evaluate the Z‐average size, with values summarized in the second column in Table 2. The effective BSA diameter was smallest in the phosphate buffer (7.1 nm) and increased to nearly 8 nm in the acetate buffer.
FIGURE 1.

BSA size distribution determined by dynamic light scattering in the phosphate, histidine, citrate, and acetate buffers at pH 4.8.
The small differences in BSA size (and diffusivity) also lead to differences in the filtrate flux behavior as seen in Figure 2. The flux at low TMP is determined primarily by the resistance of the membrane, which is independent of the buffer. At high TMP, the filtrate flux becomes mass transfer‐limited due to the accumulation of retained protein within the concentration polarization boundary layer. The highest filtrate flux is obtained with BSA in the phosphate buffer (smallest diameter and largest diffusivity), with the lowest flux in the acetate buffer, both of which are consistent with the Z‐average size determined by DLS (Table 2).
FIGURE 2.

Filtrate flux as a function of transmembrane pressure for 15 g/L solutions of BSA in the phosphate, histidine, citrate, and acetate buffers at pH 4.8. Data obtained in the Amicon stirred cell using 30 kDa Omega membranes.
3.2. Biophysical characterization
The differences in BSA transmission in the different buffers does not appear to be due to differences in protein charge in the different buffers. The measured zeta potential for BSA at pH 4.8 was quite small in all 4 buffers with values ranging from −0.4 to −2.0 mV. The zeta potential in the phosphate buffer (−1.1 mV) was between that in histidine and citrate, suggesting that these small differences in protein charge were not the dominant factor controlling the sieving behavior.
It is well known that BSA undergoes significant conformational changes as a function of solution pH, 18 , 19 but all the ultrafiltration and DLS data in Table 2 and Figure 1 were obtained at pH 4.8. This indicates that pH is not the sole factor governing these conformational changes. Additional insights into the BSA structure were obtained by CD spectroscopy, with the CD spectra in the phosphate, acetate, and citrate buffers shown in Figure 3. It was not possible to obtain a CD spectrum in the histidine buffer due to the strong signal associated with the histidine arising from the absorbance of the imidazole group. The alpha helix has negative peaks at 208 and 222 nm with a positive peak at 193 nm. The beta‐sheet structure usually results in a negative peak around 218 nm and a positive peak around 195 nm. The greatest alpha‐helical content is seen in the phosphate buffer, with the smallest amount of alpha‐helix seen in acetate. This corresponds to the observed variation in mean diameter determined by DLS (Table 2), suggesting that the differences in protein size may be due to small but significant changes in the BSA conformation with the tighter packing of the amino acids in the alpha‐helix leading to a smaller hydrodynamic diameter. 20 This behavior is consistent with previous studies showing direct interactions between BSA and mono‐ and di‐phosphate as determined by intrinsic fluorescence quenching measurements. 21
FIGURE 3.

Circular dichroism (CD) spectra for BSA in phosphate, acetate, and citrate buffers at pH 4.8.
The change in alpha‐helix content in the different buffers also affects the thermal stability of the protein as determined by DSC. Results are shown in Figure 4 for the calculated heat capacity, determined from the measured heat flow using the specific buffer associated with the respective protein solution as a reference. The DSC curve in the phosphate buffer is shifted strongly to the right (toward higher temperatures), reflecting an increase in thermal stability. 22 The DSC results in the histidine, acetate, and citrate buffers show two distinct peaks, reflecting separate transitions for the different domains within BSA. 23 , 24 The data for the phosphate buffer are also best fit using two peaks, although the first peak (at lower temperature) appears as more of a shoulder on the larger second peak.
FIGURE 4.

Differential scanning calorimetry (DSC) results showing the heat capacity as a function of the temperature for BSA in the different buffers.
The DSC and CD data are summarized in Table 3. The total alpha‐helix content ranges from 33% in the acetate buffer to 48% in the phosphate buffer. Note that Chudzik et al. 25 reported an alpha‐helix content of 40.9% for BSA in Tris buffer at pH 7.4, which falls within the same range as that measured in this work. The regular alpha‐helix (often referred to as the classical alpha‐helix) content is approximately 2/3 of the total alpha‐helix; the difference in these values reflects the presence of distorted helices in the BSA structure. 26 The DSC data in the phosphate, acetate, and citrate buffers were all well‐described by two distinct transitions; the data in histidine suggest the presence of a third transition at 72°C. There is a strong correlation between the protein stability (as determined by either T m1 or T m2) and the alpha‐helix content, consistent with previous results. 27
TABLE 3.
Total and regular alpha‐helix content (from circular dichroism) and melting temperatures (from differential scanning calorimetry) in the different buffers.
| Total alpha‐helix | Regular alpha‐helix | T m1 (°C) | T m2 (°C) | T m3 (°C) | |
|---|---|---|---|---|---|
| Phosphate | 48% | 31% | 70 | 74 | ‐ |
| Acetate | 33% | 21% | 61 | 70 | ‐ |
| Citrate | 41% | 23% | 62 | 69 | ‐ |
| Histidine | ‐ | 57 | 66 | 72 |
3.3. Correlation of transmission
The BSA sieving data in the different buffers are summarized in Figure 5, with the sieving coefficient plotted as a function of the Z‐average size determined by DLS (left panel) and the first melting temperature determined by DSC (right panel). The BSA transmission is highest in the phosphate buffer, which also yields the smallest hydrodynamic diameter and the largest melting temperature. Both plots show a reasonable correlation with R 2 = 0.76 for the hydrodynamic diameter and R 2 = 0.85 for T m1 (since the melting temperature is itself highly correlated with the effective hydrodynamic diameter due to the dependence of both of these physical properties on the alpha‐helix content of the BSA). The small discrepancies could be due to the effects of weak electrostatic interactions in these low conductivity buffers (discussed in more detail in the next section).
FIGURE 5.

Correlation of BSA transmission with hydrodynamic diameter (left panel) and melting temperature (right panel).
3.4. pH and salt effects
Additional experiments with the Omega 30 kDa membrane were performed at pH 6.5. The BSA transmission at a flux of 40 LMH in a 20 mM phosphate buffer at pH 6.5 was only 0.005 ± 0.001, which is more than a factor of two smaller than that obtained in the 20 mM phosphate buffer at pH 4.8. This reduction in transmission is likely due to a combination of conformational changes (as noted by the smaller alpha‐helix content at pH 6.5) and the greater electrostatic repulsion between the more negatively charged BSA and the negatively charged Omega polyethersulfone membranes at pH 6.5; Burns and Zydney 11 reported a zeta potential of −17 mV for the Omega 100 kDa membrane at pH 6.6.
The importance of electrostatic interactions at pH 6.5 was confirmed by repeating the sieving experiment but in the presence of 100 mM NaCl. The addition of NaCl to the 20 mM phosphate buffer caused more than a 3‐fold increase in BSA transmission, with S o = 0.015 ± 0.001. A similar increase in protein transmission was observed upon addition of MgCl2, suggesting that this is not due to any specific interactions with the salt but is instead related to the shielding of the repulsive electrostatic interactions at higher ionic strength. This behavior is also consistent with the reduction in the Debye length with increasing ionic strength 12 :
| (4) |
where ε is permittivity of the medium, R is the ideal gas constant, T is the absolute temperature, F is Faraday's constant, and I is the ionic strength. The Debye length decreases from 2.1 nm in the 20 mM ionic strength solution to only 0.87 nm in the solution with 100 mM NaCl.
The effects of pH and NaCl on BSA transmission in the phosphate and histidine buffers are summarized in Figure 6. The BSA sieving coefficients in histidine buffer are smaller than those in the phosphate buffer under all conditions, consistent with the higher alpha‐helix content and tighter internal “packing” of the BSA in the phosphate buffer. In the absence of NaCl, the sieving coefficients at pH 6.5 are smaller than those at pH 4.8 due to a combination of conformational changes and the stronger electrostatic repulsion between the negatively charged protein and negatively charged membrane at pH 6.5; the isoelectric point of BSA is approximately pH 4.8. The addition of 100 mM NaCl caused a large increase in BSA transmission in the phosphate buffer, an effect that was not seen in histidine. However, the data obtained in the histidine buffer at pH 6.5 and 100 mM NaCl showed an unusually high level of fouling, and this may have led to the lower sieving coefficient under these conditions.
FIGURE 6.

BSA sieving coefficients in phosphate and histidine buffers at pH 4.8 and 6.5 both with and without added NaCl.
4. CONCLUSIONS
Protein sieving losses can have a significant impact on the overall economics of the final UFDF step used in the formulation of high value biotherapeutics. The data obtained in this study provide the first quantitative evaluation of the effects of different buffers on the transmission of a model protein (BSA) through highly‐retentive ultrafiltration membranes. BSA transmission through two polyethersulfone (Biomax and Omega) and one composite regenerated cellulose (Utracel) membrane were similar, with the highest transmission obtained for the BSA in phosphate buffer. The phosphate buffer also yielded the greatest flux (at high transmembrane pressures), although the greater yield loss under these conditions would likely have a much greater impact on the overall process economics.
The increased BSA transmission in the phosphate buffer could be attributed to the small conformational changes in the protein, which were observed in both CD spectroscopy and DSC. The BSA showed a greater alpha‐helix content in the phosphate buffer, which led to a higher stability (greater melting temperature) and smaller hydrodynamic diameter (as determined by DLS). The observed correlation between BSA transmission and melting temperature could offer a rapid method for early screening of buffers, utilizing minimal amounts of product, either to identify conditions that are likely to minimize sieving yield losses in the final formulation step or to determine whether the optimized formulation buffer might require the selection of a lower MWCO membrane (smaller pore size) to achieve the desired TFF performance.
Although the 30 kDa membrane used in this study has a larger MWCO than would be recommended for BSA ultrafiltration (ratio of MWCO to protein MW of 45% compared with the 25%–33% recommended by Schultz et al. 7 ), the phenomena observed in these experiments are likely to be applicable to other proteins with lower MWCO membranes in which the buffer can cause significant changes in protein conformation and effective size. This includes the effects of excipients on the protein size, for example, the addition of sucrose has been shown to cause a significant increase in the effective hydrodynamic diameter of a monoclonal antibody in a 20 mM histidine buffer. 28 Additional studies will be needed to demonstrate how to best utilize these results for the development of effective UFDF processes for the final formulation of important biotherapeutics like monoclonal antibodies and Fc‐fusion proteins.
AUTHOR CONTRIBUTIONS
Aylin Mohammadzadehmarandi: Investigation; writing – original draft; formal analysis; data curation. Andrew L. Zydney: Conceptualization; funding acquisition; writing – review and editing; project administration; supervision.
CONFLICT OF INTEREST STATEMENT
The authors declare no conflict of interest.
ACKNOWLEDGMENTS
This work was supported through the Membrane Science, Engineering, and Technology (MAST) Center, which is funded by grant numbers 1841474 and 2310832 from the NSF IUCRC program. The authors would also like acknowledge technical discussions with Joseph Hersey, Christina Carbrello, and Jonathan Steen at MilliporeSigma; Xiaosong Wu, Siavash Darvishmanesh, and Rajeshwar Chinnawar at Pall/Cytiva; Sanjay Nilapwar at Abbvie; and Pranali Shah at Amgen. Zachary Vinitski assisted with some of the experiments.
Mohammadzadehmarandi A, Zydney AL. Buffer effects on protein sieving losses in ultrafiltration and their relationship to biophysical properties. Biotechnol. Prog. 2024;40(6):e3481. doi: 10.1002/btpr.3481
DATA AVAILABILITY STATEMENT
The data that support the findings of this study are available from the corresponding author upon reasonable request.
REFERENCES
- 1. van Reis R, Frautschy E, Whiteley R, Zydney AL, Goodrich B. Constant C wall ultrafiltration process control. J Membr Sci. 1997;130:123‐140. [Google Scholar]
- 2. Wang S, Lu A, Zhang L. Recent advances in regenerated cellulose materials. Prog Polym Sci. 2016;53:169‐206. [Google Scholar]
- 3. Rao S, Gefroh E, Kaltenbrunner O. Recovery modeling of tangential flow systems. Biotechnol Bioeng. 2012;109:3084‐3092. [DOI] [PubMed] [Google Scholar]
- 4. Arunkumar A, Singh N, Schutsky EG, et al. Effect of channel‐induced shear on biologics during ultrafiltration/diafiltration (UF/DF). J Membr Sci. 2016;514:671‐683. [Google Scholar]
- 5. Wang L, Yang G, Xing W, Xu N. Mathematic model of the yield for diafiltration processes. Sep Purif Technol. 2008;59(2):206‐213. [Google Scholar]
- 6. van Reis R, Zydney AL. Bioprocess membrane technology. J Membr Sci. 2007;297:16‐50. [Google Scholar]
- 7. Schultz JE, Lutz H, Rao S. Quality by design as applied to drug substance formulation using ultrafiltration and diafiltration. In: Jameel F, Hershenson S, Khan M, Martin‐Moe S, eds. Quality by Design for Biopharmaceutical Drug Product Development. AAPS Advances in the Pharmaceutical Sciences Series. Vol 18. Springer; 2015. [Google Scholar]
- 8. van Reis R. Charged filtration membranes and uses therefor. U.S. patent 7,001,550 B2, 2006.
- 9. Mulherkar P, van Reis R. Flex test: a fluorescent dextran test for UF membrane characterization. J Membr Sci. 2004;236(1–2):171‐182. [Google Scholar]
- 10. Rohani MM, Zydney AL. Role of electrostatic interactions during protein ultrafiltration. Adv Colloid Interface Sci. 2010;160:40‐48. [DOI] [PubMed] [Google Scholar]
- 11. Burns DB, Zydney AL. Effect of solution pH on protein transport through ultrafiltration membranes. Biotechnol Bioeng. 1999;64(1):27‐37. [DOI] [PubMed] [Google Scholar]
- 12. Pujar NS, Zydney AL. Electrostatic effects on protein partitioning in size‐exclusion chromatography and membrane ultrafiltration. J Chromatogr A. 1998;796:229‐238. [DOI] [PubMed] [Google Scholar]
- 13. Suryawirawan E, Janssen AEM, Boom RM, van der Padt A. Bovine serum albumin rejection by an open ultrafiltration membrane: characterization and modeling. Membranes. 2024;14:26. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 14. Menon MK, Zydney AL. Effect of ion binding on protein transport through ultrafiltration membranes. Biotechnol Bioeng. 1999;63:298‐307. [PubMed] [Google Scholar]
- 15. Rodríguez Furlán LT, Campderrós ME. Effect of Mg2+ binding on transmission of bovine serum albumin (BSA) through ultrafiltration membranes. Sep Purif Technol. 2015;150:1‐12. [Google Scholar]
- 16. Ugwu SO, Apte SP. The effect of buffers on protein conformation stability. Pharm Technol. 2004;28:86‐108. [Google Scholar]
- 17. Katayama DS, Nayar R, Chou DK, et al. Effect of buffer species on the thermally induced aggregation of interferon‐tau. J Pharm Sci. 2006;95(6):1212‐1226. [DOI] [PubMed] [Google Scholar]
- 18. Fehér B, Lyngsø J, Bartók B, et al. Effect of pH on the conformation of bovine serume albumin—gold bioconjugates. J Mol Liq. 2020;309:113065. [Google Scholar]
- 19. Jachimska B, Wasilewska M, Adamczyk Z. Characterization of globular protein solutions by dynamic light scattering, electrophoretic mobility, and viscosity measurements. Langmuir. 2008;24(13):6867‐6872. [DOI] [PubMed] [Google Scholar]
- 20. English LR, Tilton EC, Ricard BJ, Whitten ST. Intrinsic α helix propensities compact hydrodynamic radii in intrinsically disordered proteins. Proteins. 2017;85:296‐311. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 21. Bakkialakshmi S, Shanthi B, Chandrakala D. Interaction of potassium mono and di phosphates with bovine serum albumin studies by fluorescence quenching method. J Fluoresc. 2011;21:687‐692. [DOI] [PubMed] [Google Scholar]
- 22. Petukhov M, Kil Y, Kuramitsu S, Lanzov V. Insights into thermal resistance of proteins from the intrinsic stability of their α‐helices. Proteins Struct Funct Genet. 1997;29(3):309‐320. [DOI] [PubMed] [Google Scholar]
- 23. Barone G, Giancola C, Verdoliva A. DSC studies on the denaturation and aggregation of serum albumins. Thermochim Acta. 1992;199:197‐205. [Google Scholar]
- 24. Giancola C, de Sena C, Fessas D, Graziano G, Barone G. DSC studies on bovine serum albumin denaturation. Effects of ionic strength and SDS concentration. Int J Biol Macromol. 1997;20:193‐204. [DOI] [PubMed] [Google Scholar]
- 25. Chudzik M, Maciazek‐Jurczyk M, Pawelczak B, Sulkowska A. Spectroscopic studies on the molecular ageing of serum albumin. Molecules. 2017;22(1):34. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 26. Geetha V. Distortions in protein helices. Int J Biol Macromol. 1996;19(2):81‐89. [DOI] [PubMed] [Google Scholar]
- 27. Serrano L, Sancho J, Hirshberg M, Fersht AR. Alpha‐helix stability in proteins. I. Empirical correlations concerning substitution of side‐chains at the N and C‐caps and the replacement of alanine by glycine or serine at solvent‐exposed surfaces. J Mol Biol. 1992;227(2):544‐559. [DOI] [PubMed] [Google Scholar]
- 28. Baek Y, Singh N, Arunkumar A, Zydney AL. Effects of histidine and sucrose on the biophysical properties of a monoclonal antibody. Pharm Res. 2017;34(3):629‐639. [DOI] [PubMed] [Google Scholar]
Associated Data
This section collects any data citations, data availability statements, or supplementary materials included in this article.
Data Availability Statement
The data that support the findings of this study are available from the corresponding author upon reasonable request.
