Abstract
Potassium‐ion batteries (PIBs), with abundant resources and low cost, are considered as a promising alternative to commercial lithium‐ion batteries for low‐cost and large‐scale applications. Over the past decade, significant academic progresses are made in the development of PIBs, including advancements in cathodes, anodes, and electrolytes. However, most improvements are achieved under laboratory conditions (e.g., K metal‐based half‐cells and low mass loading of active materials), and the performance of PIBs in full cells is still far from the requirements for commercial applications. A critical insight bridging the academic research and the commercialization of PIBs is urgently needed to guide future research in this field. This review will discuss the challenges and improvement strategies in the development of PIBs, focusing on the potential practical cathodes, anodes, and electrolytes, as well as their performance in full cells. It aims to give the readers a clear and logical understanding of the development of PIBs. The application analysis is also discussed to provide a comprehensive understanding of the commercialization potential of PIBs. Finally, perspectives are provided for the future development of PIBs.
Keywords: anode, cathode, electrolyte, full cell, potassium‐ion batteries
Significant progress is made in PIBs over the past decade, but the improvements based on half‐cell testing, low mass loading, and low energy density are insufficient for practical applications. This review summarizes the challenges and strategies for PIBs, highlights the importance of further research focusing on full cells, and provides an analysis of their practical application potential.

1. Introduction
To address the shortage of fossil fuels and global climate change, there is an increasing global focus on energy storage systems to facilitate the large‐scale applications of green and sustainable energy. Lithium‐ion batteries (LIBs) with high energy density and long lifespans have dominated the market for over 30 years. However, LIBs are not a suitable choice for large‐scale electric grid applications, due to their limited resources and high cost.[ 1 ] The Li resources are limited to only 32 ppm globally, and their scarcity and uneven distribution significantly increase the extraction costs, ultimately increasing the price for LIBs.[ 2 ] Therefore, exploring low‐cost and high‐energy‐density energy storage system is necessary. Currently, there are many potential energy storage systems including, potassium‐ion batteries (PIBs), sodium‐ion batteries (SIBs), zinc‐ion batteries (ZIBs) and so on.[ 3 ] PIBs have their advantages as a candidate for next‐generation energy storage devices, Figure 1a.[ 4 ] The redox potential of K/K+ is lower (‐2.92 V vs standard hydrogen electrode (SHE)) compared to Na/Na+ (‐2.71 V vs SHE) and Zn/Zn2+ (‐0.76 V vs SHE), and is only 0.09 V higher than that of Li/Li+. This lower redox potential can reduce the energy density loss, as the metal's redox potential significantly influences the reduction voltage of the negative electrode, which in turn affects the operational voltage and overall energy density of the battery.[ 5 ] K resource is abundant (with a concentration of 25 000 ppm in the earth crust) and its raw materials are low‐cost, as shown in Table 1 . This can reduce the cost of electric grids and accelerate the application of green energy. Compared to SIBs, K+ can form stable K‐graphite intercalation compounds (K‐GIC). Therefore, graphite, with its low volume change and intercalation potential, can be applied in PIBs to achieve a long lifespan and high energy density.[ 6 ] Compared to Li+ (0.76 Å), Na+ (1.02 Å), and K+ (1.38 Å), have larger ionic radius, but their lower charge density and lower Lewis acidity would result in a reduced interaction between K+ and solvents. This decreases the de‐solvation energy and Stokes radius in solvents (e.g., K‐propylene carbonate (PC) (3.6 Å), Na‐PC (4.6 Å), and Li‐PC (4.8 Å), Zn‐H2O (130 Å),[ 7 ]) promoting fast ion transport at the electrode interface. The low de‐solvation energy and high‐rate capability of K+ contribute to high power density of PIBs. Therefore, PIBs have been considered as one of the most promising candidates for next generation energy storage systems.
Figure 1.

a) Comparison of LIBs, SIBs, ZIBs, and PIBs in terms of crust abundance (ppm), potential (‐V vs SHE), cost of raw materials ($ ton−1 based on carbonates materials and zinc sulfide for ZIBs), volumetric energy density (Wh L−1), and energy density (Wh Kg−1). b) Number of publications on “potassium battery” from the Web of Science (August 2024).
Table 1.
Abundance, cost, and main distribution regions of Li, Na, K, and Zn resources.
| Abundance in earth crust (ppm)[ 10 ] | Cost of raw materials ($ ton−1)[ 11 ] | Main distribution regions[ 12 ] | |
|---|---|---|---|
| Li | 32 | 26 400 (Li2CO3) | China, Peru, Australia, India, the United States, Mexico, Bolivia and Russia. |
| Na | 25 000 | 100 (Na2CO3) | China, the United States, India, Russia, and Germany. |
| K | 25 000 | 250 (K2CO3) | Canada, Russia, and Germany. |
| Zn | 83 | 150 (ZnS) | Australia, Chile, China, and Argentina. |
The K+ storage mechanism in PIBs is similar to that of Li+ in LIBs. During charging, K+ intercalates into the graphite anode, then de‐intercalates and moves back into the cathode compounds during discharging, enabling the reversible energy storage.[ 8 ] For alloy anodes, K+ is stored via metal alloy reactions.[ 9 ] Over the past decade, driven by a strong focus on reducing carbon emissions and promoting green energy, there has been a rapid development in PIBs, including advancements in cathodes, electrolytes, and anodes, Figure 1b. All these progresses indicate the significant commercial potential for PIBs. However, most of these achievements stem from laboratory research involving a high electrolyte weight/active materials capacity (E/C) ratio, low mass loading of active materials, and half‐cell configurations. There remains a substantial gap between the laboratory research and commercialization of PIBs.
In this review, the authors assess the development of cathode, anode, and electrolyte in PIBs over the past decades and discuss the challenges and solutions for potential practical materials. The practical potential of PIBs will be discussed in terms of cost, large‐scale industrialization, and advantages for electric grids, providing a clear understanding of their important role in future energy storage systems. This review aims to offer a guidance on the development of PIBs, emphasizing the key directions for industrial applications. Overall, the authors hope to provide reads a comprehensive understanding of the potential and commercialization of PIBs.
2. The Search for Cathode and Anode in PIBs
Similar to LIBs, the cathode and anode materials are crucial in determining the electrochemical performance of PIBs. Throughout the development of PIBs, the search for commercial cathode and anode materials never stops, with all efforts focused on identifying better materials to achieve high energy density and long lifespan.
2.1. The Search for Cathode
A wide range of materials, including Prussian blue and its analogs (PBAs), layered transition metal oxides (LTMOs), polyanionic compounds, and organic materials, have been explored as potential cathodes in PIBs, Figure 2 .[ 13 ] Due to their diverse structural properties, each material offers unique K+ storage mechanisms, which influence their overall electrochemical performance, including capacity, cycling stability, rate capability, and cost‐effectiveness.
Figure 2.

Summary of cathodes used in PIBs and strategies for improvement. (PBAs refer to Prussian blue and its analogs cathode and LTMOs are layered transition metal oxides).
2.1.1. Prussian Blue and Its Analogs (PBAs)
PBAs are compounds formed through the reaction of metal ions with transition metal cyanometallates. Generally, they can exhibit as AxM[M’(CN)6]y·zH2O, where A represents alkali metal,mand M’ represent transition metals. In PBAs, two transition metals are connected by cyano ligands, forming a 3D open‐framework structure that facilitates the intercalation of alkali metal ions.[ 14 ] During charge/discharge process, themand M’ transition metal centers undergo changes in their valence states to facilitate K+ intercalation and de‐intercalation. Some PBAs have been investigated as cathode materials in PIBs, such as KxM[Fe(CN)6] and KxM[Mn(CN)6]. [ 15 ] Due to their high redox potential, low‐cost raw materials, and environmentally friendly synthesis, the KxM[Fe(CN)6] materials have garnered increasing attention, particularly KxFe[Fe(CN)6].[ 16 ] KFe[Fe(CN)6] shows a capacity of 75 mAh g−1 in PIBs with good cycling stability (80% capacity after 500 cycles).[ 17 ] With optimized morphology, the KFe[Fe(CN)6] nanoparticles achieved a discharge capacity of 118.7 mAh g−1 at 10 mA g−1 and good cycling stability with a capacity of 111.3 mAh g−1 after 100 cycles in PIBs.[ 18 ] The transition metal centers in KxM[Fe(CN)6]·yH₂O influence the intercalation/extraction of one or two K+. For example, K0.22Fe[Fe(CN)6]0.805·4.01H2O and K1.81Ni[Fe(CN)6]0.97·0.086H2O showed only one K+ storage, as indicated by their cyclic voltammetry curves and corresponding galvanostatic charge/discharge profiles.[ 19 ] However, K1.89Mn[Fe(CN)6]0.92·0.75H2O exhibited two plateaus at 4.23 and 4.26 V (vs K/K+) in the galvanostatic charge profile, indicating two K+ storage sites. As a result, this cathode, which accommodates more K+, can achieve a high capacity of 156 mAh g−1 and maintain 90% capacity retention after 100 cycles, Figure 3a,b.[ 20 ]
Figure 3.

Electrochemical performance of typical cathodes. a) Charge/discharge curve and b) cycling performance of KxMn[Fe(CN6)] at 1 C. (Reproduced with permission.[ 20 ] Copyright 2017, American Chemical Society). c) Charge/discharge curves and d) cycling performance of K0.45MnO2 at 20 mA g−1. (Reproduced with permission.[ 21 ] Copyright 2019, Elsevier). e) Charge/discharge curve of PTCDA cathode at various current densities and f) cycling performance at 50 mA g−1. (Reproduced with permission.[ 22 ] Copyright 2015, Elsevier). g) Charge/discharge curves and h) cycling performance of K3V2(PO4)2F3 | graphite full cells. (Reproduced with permission.[ 23 ] Copyright 2019, Elsevier).
Another advantage of PBAs is low cost and simple preparation. Besides the inexpensive raw materials for K, the transition metals used in PBAs, such as Fe and Mn, are also low‐cost, making the high potential for reducing the overall cost of PIBs and accelerating their commercialization. Most PBAs are prepared by hydrothermal synthesis in the aqueous environment avoiding the use of expensive organic solvents and minimizing energy consumption. Therefore, PBAs are the ideal choice as cathode material in PIBs.
2.1.2. Layered Transition Metal Oxides (LTMOs)
Inspired by the good performance of LTMOs such as LiCoO2 and Li(NixCoyMnz)O2 in LIBs, there is also research on LTMOs for the cathode in PIBs.[ 13 ] LTMOs are compounds that consist of layers of alkali metal ions and transition metal oxides. There are three types LTMOs in PIBs: P2, P3, and O3. The “P” and “O” represent the different coordination environments of alkali metal ions (prismatic and octahedral, respectively), “2” and “3” are the number of transition metal oxide layers in each unit cell. Generally, the LTMOs for PIBs include KxMO2, wheremcould be Mn, Co, Cr, Vn, and others; all of them have great potential for practical PIBs.
KxMnO2
KxMnO2 with abundant raw materials, low toxicity, and high operational voltage is a promising cathode material in PIBs. K0.3MnO2 was reported to deliver an initial capacity of 70 mAh g−1 at 27.9 mA g−1 and maintain 40 mAh g−1 after 685 cycles.[ 24 ] The concentration of K+ in LTMOs significantly impacts their structure, which in turn affects their electrochemical performance. By increasing K+ from K0.3MnO2 to K0.45MnO2, the structure changed from P2 to P3. Due to its high structural stability, K0.45MnO2 exhibited a wider voltage window of 1.5–4.0 V (vs K/K+) and better cycling stability, maintaining 70 mAh g−1 after 100 cycles at 20 mA g−1, Figure 3c,d.[ 21 ] K0.5MnO2 exhibited reversible P3‐O3‐X (X phase: a new X‐Ray diffraction (XRD) peak appears at x ≈ 0.34 in KxMnO2) transitions as confirmed by experiment and density functional theory (DFT) results, indicating strong structural stability during K+ intercalation and de‐intercalation. As a result, the K0.5MnO2 cathode showed stable cycling performance.[ 25 ] And the Mn element shows abundant natural resources and low toxicity, which provides a guarantee for the large‐scale application of environmentally friendly cathodes.
KxCoO2 and KxCrO2
Following the success of commercial LiCoO2 | graphite in LIBs, the KxCoO2 is also a candidate for the cathode in PIBs. P2 type KxCoO2 (0.23 < X < 0.47) cathode delivered 60 mAh g−1 with multiple plateaus.[ 26 ] At higher K+ concentration, P2 K0.6CoO2 showed a capacity of 80 mAh g−1 at 2 mA g−1 with an output voltage of 2.7 V (vs K/K+). However, the high K+ content negatively impacts the structural stability of KxCoO2, leading to a poor cycling stability in K0.6CoO2 cathode.[ 27 ] Due to strong K+‐K+ repulsion, most LTMOs cannot achieve fully K+ accommodation in KxMO2 (x < 0.7), except KCrO2. The Cr3+‐ligand field can compensate for the K+‐K+ repulsion, achieving better K+ accommodation. As a result, there is a higher K+ concentration in KCrO2.[ 28 ] The O3 KCrO2 cathode showed reversibly structural changes (O3‐Oʹ3‐Pʹ3‐P3‐Pʹ3‐P3‐O3), resulting in a multistep voltage profile during charge/discharge process. The full cell PIBs using KCrO2 as cathode delivered a capacity of ≈82 mAh g−1 at 5 mA g−1.[ 29 ] The P3 K0.8CrO2 cathode showed reversible transition, fast K+ diffusion, and good cycling performance, due to less O3 structure and good stability of P3 structure.[ 30 ] Another structure P3 K0.69CrO2, obtained through ions exchange from O3 NaCrO2, exhibited a good capacity of 100 mAh g−1 at 10 mA g−1 with a voltage range of 1.5–3.8 V (vs K/K+).[ 31 ]
KxV2O5
Because vanadium shows multiple valence states, vanadium oxide could achieve more K+ storage. K0.83V2O5 has been used as a cathode in PIBs, demonstrating a capacity of 90 mAh g−1 with a working voltage of 3.5 V (vs K/K+). The KxV2O5 (0 < x ≤ 0.875) exhibited a high K+ diffusion coefficient of 10−15‐10−12 cm2 s−1. Therefore, the K0.83V2O5 | graphite full cell achieved an energy density of 136 Wh kg−1.[ 32 ] The K2V3O8 has also been explored as a cathode in PIBs, showing a capacity of 100 mAh g−1 with a discharge voltage of 2.7 V (vs K/K+). But the large volume change in K+ extraction/insertion process caused poor cycling stability (27% capacity loss after only 50 cycles).[ 33 ] A layered K0.4V2O5 cathode was modified by Sr2+ doping to improve vacancies at K sites and enhance K+ diffusion kinetics. After modification, the K0.34Sr0.03V2O5 cathode suppressed irreversible phase transition, exhibiting higher reversible capacity and rate capability.[ 34 ]
From the above discussion, the LTMOs can show reversible K+ storage and high capacity. The high redox potential of LTMOs cathode also contributes to high operational voltage for higher energy density, Figure 2. The adjustable chemical composition of LTMOs enables the optimization of their electrochemical performance, ensuring stable cycling across diverse operational conditions and environments in PIBs. Therefore, LTMOs cathode are also promising candidates for PIBs.
2.1.3. Polyanion Materials
Due to the strong covalent interaction, polyanion‐type materials show high redox potential and high structure stability, and hence attract great attention for cathode materials in PIBs. According to transition metals and polyanion groups, polyanion materials can be classified into phosphate, pyrophosphate, sulfates, and fluoro‐phosphates.[ 16 ]
Phosphate
The most famous phosphate polyanion cathode would be LiFePO4, which is widely used in commercial LIBs. In phosphate, the PO4 tetrahedra shows an open structure for ion diffusion, and good structure stability. This makes phosphates an attractive candidate for PIB cathodes. But the olivine phase KFePO4 can't accommodate large K+, and the reversible K+ insertion is not achieved.[ 35 ] In contrast, the amorphous FePO4 can show 156 mAh g−1 with a voltage range of 1.5 to 3.5 V (vs K/K+), but it has a low capacity retention of 70% after 50 cycles.[ 36 ] The transition metal center also significantly impacts the electrochemical performance of polyanion materials. KVOPO4 was proposed for the cathode in PIBs. The ex‐situ XRD showed the original structure can be recovered after the charge/discharge process, demonstrating good structure stability. Even charging to 5.0 V (vs K/K+), there is only 3.3% lattice volume shrinkage in KVOPO4. Finally, KVOPO4 cathode showed a capacity of 84 mAh g−1 with a high operational voltage of 4.0 V (vs K/K+).[ 37 ] After morphology control via hydrothermal preparation, the layered KVOPO4 with fast ion diffusion channels showed a high capacity of 115 mAh g−1 at 0.2 C.[ 38 ] A pure phase KVOPO4, synthesized by carbothermal reduction method, showed 3D framework and numerous K sites, enabling fast K+ diffusion during cycling. This pure phase KVOPO4 showed a capacity of 63 mAh g−1 at 0.1 C after 100 cycles with good capacity retention. The pure phase KVOPO4 | hard carbon full cell achieved 60 mAh g−1 at 0.2 C after 700 cycles.[ 39 ]
Pyrophosphates and Sulfates
The pyrophosphates, KxMP2O7 (M: transition metal), is also used as a cathode for PIBs. KVP2O7 cathode showed 60% reversible K+ interaction/de‐interaction, as confirmed by energy dispersive X‐ray spectroscopy (EDX) and X‐ray photoelectron spectroscopy (XPS) results. Nudged elastic band (NEB) showed that there were different channels for K+ diffusion in K1‐xVP2O7, with the activation energy along the (100) direction being the lowest compared to the (001) and (010) directions. Finally, the KVP2O7 cathode showed a high capacity of 60 mAh g−1 with high discharge voltage of 4.2 V (vs K/K+).[ 40 ] For sulfate, the yavapaiite‐type KFe(SO4)2 has been reported as a cathode in PIBs. There was a single phase change in K+ extraction process in KFe(SO4)2 with a small volume change of 1.83%. The lower activation energy also facilitated the fast migration of K+. Consequently, KFe(SO4)2 cathode showed a high capacity of 93 mAh g−1 at 0.05 C and good rate performance.[ 41 ]
Fluoro‐Derivatives
The fluoro‐polyanions materials can achieve high redox potential due to “inductive effect” of the F atom in the structure. Therefore, there is much research focused on fluoro‐derivatives polyanion cathodes in PIBs. For example, K3V2(PO4)2F3 undergoes a phase transformation from K3V2(PO4)2F3 to K1V2(PO4)2F3 with a small volume change of 6.2%, enabling a high capacity retention of 80%, Figure 3g,h.[ 23 ] The KVPO4F has also been explored as cathode in PIBs, the structure underwent single phase change in K+ insertion/de‐insertion process from operando XRD results, and the Rietveld refinements results indicated there was a small volume change of 5.8% in potassiation process, further confirming good structural stability. Finally, the cathode achieved a capacity of 92 mAh g−1 at 0.2 C.[ 37 ]
Polyanion materials with strong covalent bond can improve redox potential and structural stability, which is beneficial for higher energy density and longer lifespan in PIBs, Figure 2. The diverse range of transition metal centers and covalent interactions expands the variety of polyanion materials, providing numerous opportunities for optimization. Their low cost further enhances their appeal, making polyanion materials a promising choice for large‐scale applications in PIBs and boosting their competitiveness. Therefore, polyanion materials attract significant attention in the development of PIBs.
2.1.4. Organic Compounds
Organic materials are also used for PIBs cathode, because of their environmental compatibility and low cost. The most famous organic cathode would be 3,4,9,10‐perylene‐tetracarboxylicaciddianhydride (PTCDA) and its derivatives. PTCDA can accommodate 11 K+ ions per unit, delivering 131 mAh g−1 with a working windows of 1.5–3.5 V (vs K/K+), Figure 3e,f.[ 22 ] There are also other organic cathodes in PIBs. The poly(pentacenetetrone sulfide) (PPTS) as a cathode for PIBs can achieve high reversible capacity of 260 mAh g−1 at 0.1 A g−1 and fast charging at 10 A g−1.[ 42 ] The polyimide@Ketjenblack through in situ polymerization of 1,4,5,8‐naphthalenetetracarboxylic dianhydride monomers on Ketjen black as cathode showed 143 mAh g−1 at 100 mA g−1.[ 43 ] However, the organic cathode usually has low density, which will increase the cathode volume. For example, the density of KxCoO2, sulfur, and PTCDA is 3.64, 2.07, and 1.7 g cm−3, respectively. The lower density makes the cathode thicker. Although the volumetric energy density is less critical for electric grids, the thicker cathode requires larger volume of electrolyte to wet electrode. For current LIBs, the E/C ratio is ≈1.86 g Ah−1.[ 44 ] When large volume of electrolyte is used in organic cathode, it will decrease energy density and increase cost and cause risk issues (thermal runaway and explosion). The low electronic conductivity of organic cathode will also increase the use of conductive carbon, further increasing the cathode thickness and decreasing energy density. Although the PBAs also show low density, the high redox potential can mitigate the loss of energy density from lower density of cathode materials. In addition, the high solubility and poor thermal stability also limits the application of organic cathode in PIBs. Therefore, in the next part about the development challenges and strategies for the commercial cathode, we will mainly discuss PBAs, LTMOs, and polyanion cathodes.
2.2. The Search for Anode
In addition to cathode materials, selecting a suitable anode is also crucial for the development of PIBs. Several materials have been explored for the anode in PIBs, with options ranging from carbon‐based materials (e.g., graphite and hard carbon), alloy materials, conversion‐type anodes to organic materials. Each anode material for PIBs comes with its own set of advantages and challenges, Figure 4 .
Figure 4.

Advantages and disadvantages of a) graphite anodes, hard carbon anodes, alloy anodes, organic anodes, and conversion‐type anodes in PIBs. b) Summary of modification strategies for anodes in PIBs, including expanded interlayer, ions doping, surface modification, and structural design.
2.2.1. Graphite
In LIBs, the graphite can accommodate Li+ to form stable LiC6 compounds, resulting in high capacity, small volume change, and high Coulombic efficiency (CE).[ 45 ] The intercalation potential of Li+ in graphite is similar to the potential of Li/Li+, which improves the operational voltage of LIBs. Therefore, the high‐performance graphite anode is also explored as an anode for other alkali ion batteries. However, Na+ cannot be inserted into the graphite interlayer to form Na‐GICs, due to the energetically instability of Na‐GIC.[ 46 ] Fortunately, the K+ can be intercalated into graphite layers to form stable K‐GICs. Due to the larger size of K+ (1.38 Å) compared to Li+ (0.76 Å), graphite can only form KC8, with a theoretical capacity of 279 mAh g−1, Figure 5a.[ 47 ] Detailed studies about structure evolution of graphite during K+ intercalation were reported by Ji and co‐workers using ex‐situ XRD.[ 48 ] In electrochemical intercalation of K+ into graphite, the phase changed from KC36 to KC24, forming KC8 at the final stage. In the depotassiation process, KC8 directly changed to KC36 ≈0.3 V (vs K/K+) without obvious KC24 phase change. Finally, a normal graphite shoulder (002) XRD peak appeared, indicating a highly reversible intercalation and de‐intercalation process. The graphite can achieve high initial Coulombic efficiency (ICE) to decrease K+ loss during the initial activation process and improve reversible capacity and energy density. For example, there is 82% ICE in graphite using carbonate electrolyte (0.8m KPF6 in EC/DEC).[ 49 ] Graphite also shows similar redox potential with K/K+, which improves operational voltage of PIBs; therefore, graphite with high CE, is a very promising anode for PIBs.
Figure 5.

Electrochemical performance of typical anodes. a) Charge/discharge profiles of graphite with KFSI/EMC (1:2.5, molar ratio) electrolyte in PIBs. (Reproduced with permission.[ 47 ] Copyright 2019, Wiley‐VCH). b) Charge/discharge profiles of HC anode using 1 m KFSI in EC/DEC at different current densities. (Reproduced with permission.[ 51b ] Copyright 2022, Elsevier). c) Charge/discharge curves and d) cycling performance of Sn nanoclusters anode in PIBs. (Reproduced with permission.[ 57 ] Copyright 2024, Wiley‐VCH). e) Charge/discharge curves and f) cycling performance of organic pyrazine anode in PIBs. (Reproduced with permission.[ 64 ] Copyright 2023, Wiley‐VCH). g) Charge/discharge curves and h) cycling performance of ZnS anode in PIBs. (Reproduced with permission.[ 65 ] Copyright 2024, Wiley‐VCH).
2.2.2. Hard Carbon
Hard carbon (HC), has been regarded as the most promising anode for SIBs, is also an attractive anode in PIBs. HC refers to carbon materials that remain non‐graphitization even under high temperatures, primarily derived from the pyrolysis of macromolecular polymer.[ 50 ] There isn't large graphene sheet in HC; therefore, its potassiation mechanism is different from the graphite. For HC, the charge/discharge curves are a slope at high voltage and a plateau at lower voltage, indicating that K+ is absorbed on surface defects or functional groups at high voltage, then inserted into the interlayer at low voltage, Figure 5b.[ 51 ] The reversible capacity of HC (≈400 mAh g−1) is higher than that of graphite, but the voltage plateau for potassiation is higher. HC typically exhibits a plateau above 0.5 V (vs K/K+), while graphite shows a plateau at a lower voltage (<0.5 V vs K/K+). The high anode operational voltage will decrease energy density in a full cell. The ICE of HC in PIBs is low. For example, the HC, synthesized by hydrothermal carbonization method, exhibits an ICE of 70%,[ 52 ] while the single atom modified HC shows an ICE of 62.3%.[ 53 ] This low ICE results in K+ consumption during the initial cycling, which can reduce reversible capacity and energy density. The precursor compositions and pyrolysis parameters will influence active sites and structure of HC, further impacting its electrochemical performance.
2.2.3. Alloy Anodes
Different from intercalation/de‐intercalation reaction, the reversible alloy reaction will accompany more electrons transfer, indicating this type of anode can accommodate more K+ and achieve higher capacity. In addition, the alloy‐anode usually shows high density and high electron conductivity, which is beneficial to achieve high energy density in PIBs. There are many reports about alloy anodes in PIBs, including Sn, Sb, Bi, Si, P, and SnSb. Sn can alloy with K+ to form KSn compounds, which have a theoretical capacity of 226 mAh g−1. Sb and Bi can alloy with more K+ to form K3Sb and K3Bi, respectively, resulting in higher capacity (660 mAh g−1 for Sb and 385 mAh g−1 for Bi). Crystalline Si is inactive for PIBs, but amorphous Si can accommodate 1.1 K+ for high capacity of 1049 mAh g−1.[ 54 ] Due to the weak electrostatic K‐Si attraction, the diffusion rate of K+ in K‐Si compounds is fast. However, volume expansion remains a significant issue for all alloy anodes. For graphite, the volume expansion originated from lithiation and potassiation are 10% and 60%, respectively.[ 55 ] Alloy anodes experience even greater volume change after potassiation, for example, Sn exhibits 180% volume expansion, while Sb undergoes 407% volume expansion.[ 54a ] The large volume change can damage the solid electrolyte interface (SEI) and structural integrity, leading to poor cycling stability.[ 56 ]
Morphology regulation and porous structure design are common strategies employed to improve the electrochemical performance of alloy anodes in PIBs. Sn nanoclusters were encapsulated into a carbon matrix to create a high performance PIBs anode. The carbon matrix helped to suppress volume changes and provide a conductive network, ensuring stable cycling. As a result, this nanocluster Sn‐hybrid anode demonstrated fast K+ diffusion kinetics and excellent cycling stability, Figure 5c,d.[ 57 ] A dense, elastic Ti3C2Tx (Mxene) and graphene networks has been applied to buffer the volume expansion of a nano‐Sb anode in PIBs. The encapsulated nano‐Sb anode delivered a high capacity of 565.0 mAh g−1 and maintained a high capacity retention of 82% after 500 cycles in PIBs.[ 58 ] To increase tap density and suppress volume change, a 3D graphene was used to load Bi monolith, achieving a high mass loading of 24.3 mg cm−2. The Bi@graphene anode achieved a high volumetric capacity of 1032.2 mAh cm−3 and superior rate performance (271.0 mAh g−1 at 40.0 A g−1).[ 59 ] Additionally, the Mxene conductive matrix was also used to enhance the electrochemical performance of SnSb nanoparticles and maintain structural stability.[ 60 ]
Phosphorus exists in three main allotropes: red phosphorus (RP), black phosphorus (BP), and white phosphorus (WP). Compared with unstable WP, RP, and BP are more commonly studied as anode materials for PIBs. RP can form KP and K4P3 after potassiation, with capacities of 843 mAh g−1 and 1154 mAh g−1, respectively.[ 61 ] However, RP exhibits low electronic conductivity of 10−14 S cm−1, leading to poor reaction kinetics. Fluorine‐doped carbon materials can facilitate the distribution of P4 molecules and improve electronic conductivity, enabling the RP anode to demonstrate outstanding capacity retention of 90% after 800 cycles.[ 62 ] BP shows high electronic conductivity, with more research focused on alleviating volume expansion of BP anode. Sulfur‐doped graphene, which forms a covalent P‐S bond with BP, effectively withstands the high strain during the potassiation process, resulting in higher capacity of 731 mAh g−1 and excellent rate performance.[ 63 ]
2.2.4. Organic Anodes
Organic materials are also potential candidates for anodes in PIBs. An organic anode 2,5‐bis(methoxycarbonyl)‐3,6‐dioxocyclohexa‐1,4‐dienolate (K2dmcdbq) is synthesized for K+ storage. K2dmcdbq accommodates two K+ via oxygen‐related functional groups and achieves a capacity of 232 mAh g−1 at 0.2 C in ether electrolyte. Due to its quinone structure and methoxycarbonyl group, K2dmcdbq shows high structure stability, preventing the dissolution of organic materials and exhibiting better cycling retention. When combined with a PTCDA cathode, this green full cell delivered a high energy density of 119 Wh kg−1 and a power density of 113 W kg−1.[ 66 ] The hexaazatriphenylene potassium carboxylate, which contains abundant C═N/C═O bonds, can undergo a 6‐electrons transfer. When used as an anode in PIBs, it delivered a high discharge capacity of 288 mAh g−1 at 50 mA g−1.[ 67 ] To address the low electronic conductivity of organic anodes, an ultrathin layered pyrazine/carbonyl‐rich material was grown on carbon nanotubes (CNTs). This hybrid materials, with its good conductive network, exhibited highly reversible capacity and remarkable rate capability (180 mAh g−1 at 1 A g−1), Figure 5e,f.[ 64 ] Although organic anodes are low‐cost and sustainable, their disadvantages of low density, poor electronic conductivity, and high solubility in organic solvents limit their practical application.
2.2.5. Conversion Anode Materials
Conversion‐type materials with high capacity and good redox stability are also used as anodes in PIBs, such as metal sulfide,[ 68 ] metal oxides,[ 69 ] and metal selenide.[ 70 ] Due to their low conductivity and high volume change, combining them with highly conductive network is a common strategy to improve the performance of conversion‐type anodes in PIBs. The hollow core shell ZnS@C nanocomposite was designed for K+ storage. The carbon network ensured high electronic conductivity and facilitated uniform distribution of ZnS nanoparticles, accelerating electrochemical kinetics (450 mAh g−1 at 0.03 A g−1) and achieving a high capacity retention of 80%, Figure 5g,h.[ 65 ] 2D arsenic disulfide (As2S3) nanosheets, exfoliated via liquid‐phase methods, can accommodate 12 K+, offering a high theoretical capacity of 1305 mAh g−1. The As2S3@CNT anode exhibited a high discharge capacity of 619 mAh g−1 at 50 mA g−1.[ 71 ] In carbon‐coated Fe3O4 quantum dots, the amorphous carbon acted as the nucleation sites for the homogeneous distribution of Fe3O4 quantum dots and provided a buffer for volume change, leading to an excellent capacity of 329.6 mAh g−1 at 100 mA g−1 and long cycling stability for 7 months.[ 72 ] The hollow structure design has also been used to improve the metal selenide anode in PIBs. The hollow ZnSe@NiSe microspheres within N‐doped carbon nanofibers, with short mass transfer pathways, achieved a high specific capacity of 456.3 mAh g−1 at 0.1 A g−1 and maintained 305.6 mAh g−1 after 1500 cycles at 2.0 A g−1.[ 73 ] Sn4P3@C can exhibit a lower discharge voltage of 0.1 V to improve operational voltage and avoid dendrites formation. During the discharge process, Sn4P3 generates K‐Sn alloy and K‐P alloy phases which can alleviate the volume changes.[ 74 ] After morphology modification, Sn4P3@N‐doped carbon fibers anode achieved a high capacity of 403.1 mAh g−1 after 200 cycles at 50 mA g−1.[ 75 ]
In short, although the alloy anode and conversion anode can show higher capacity, and the HC anode, with its fast ions diffusion, can improve power density, the lower ICE for HC and large volume expansion for the alloy and conversion anodes cause lower energy density and poor lifespan, restricting their commercialization. In contrast, the graphite anode shows low intercalation voltage, high capacity, high ICE, small volume change, and stable cycling, making it a promising anode for PIBs.
3. The Challenges and Strategies of Potential Cathode and Anode Materials in Practical PIBs
PBAs, LTMOs, and polyanion cathodes, along with graphite anode, show great potential for application in PIBs. However, there are several challenges associated with these promising electrode materials in PIBs, which need to be addressed for large‐scale industrial application.
3.1. The Challenges and Strategies for the Cathode Development
3.1.1. PBAs Cathode
PBAs with their 3D open framework and adjustable chemical compositions, can show high capacity, high redox potential, and high energy density. However, PBAs usually suffer from crystal defects and poor electronic conductivity, which can compromise their electrochemical performance.
Crystal Defects
In PBAs, low solubility and a rapid crystallization rate often result in the presence of interstitial water within the crystal structure. This interstitial water reduces the concentration of alkali metal ions and generates vacancies, compromising the crystal structure of PBAs. As a result, there are limited K+ insertion sites and a sluggish internal transport of K+ in these crystal lattices. Therefore, some strategies are proposed to improve crystallinity for PBAs. Through recrystallization process, K1.4Fe4[Fe(CN)6]3 showed better crystal structure than KFe4[Fe(CN)6]3·xH2O, and the XRD pattern showed good structure reversibility after one cycle with a small volume change of 5.36%. With improved crystallinity, K1.4Fe4[Fe(CN)6]3 exhibited a higher calculated K+ diffusion coefficient, leading to a good rate performance.[ 76 ] Using the ethylenediaminetetraacetic acid dipotassium salt (EDTA) as a chelating agent, highly crystalline K2Fe[Fe(CN)6] was obtained by coprecipitation. The chelating agent can slow down the crystallization process, improving nucleation and crystal growth. As a result, this cathode with less crystalline water showed a capacity of 77 mAh g−1 at 25 mA g−1.[ 77 ] The potassium pyrophosphate also can be used as chelating agent for highly crystallized K2Zn3[Fe(CN)6]2. The obtained K2Zn3[Fe(CN)6]2 crystal with uniform size of 1 µm showed a high discharged capacity of 65.3 mAh g−1 at 50 mA g−1 and high capacity retention of 89.3% after 1000 cycles at 500 mA g−1.[ 78 ] Except for inorganic salts, the polymer also can be used as chelating agent to improve crystallinity. The low‐cost sodium polyacrylate showed strong coordinated ability with ferrous ions, which can regulate the diffusion and nucleation rate. Finally, the high crystalline PBAs using sodium polyacrylate as a chelating agent showed a high capacity of 140 mAh g−1 at 0.2 C and good rate performance.[ 79 ] The potassium citrate as a nucleation inhibitor can control the PBAs particle size, resulting in a hierarchically structure with large reaction surface and fast K+ diffusion. After modification in potassium citrate, K1.82Mn[Fe(CN)6]0.96·0.47H2O crystal with high crystallinity and fewer interstitial water showed high reversible capacity of 160 mAh g−1. The PIBs full cell of K1.82Mn[Fe(CN)6]0.96·0.47H2O | 3,4,9,10‐perylenetetracarboxylic diimide achieved an energy density of 92 Wh kg−1.[ 80 ] Using chelating agent to slow down the crystallization rate and improve crystallinity is a useful and cost‐effective strategy, but excessive use of chelating agents will prevent coordination between transition metals and cyano ligands, reducing nucleation of PBAs. Therefore, achieving a balance between optimal crystallinity and adequate nucleation facilitated by chelating agents is crucial. In addition to enhancing crystallinity, morphology control is another strategy to improve K+ diffusion in PBAs cathode. For instance, MnNi‐PBA spheres, obtained via a simple anion exchange method, feature a unique porous structure that shortens the K+ diffusion pathway. This results in improved rate performance of 66.3 mAh g−1 at 200 mA g−1 and a longer cycling life.[ 81 ]
Low Electronic Conductivity
Another challenge for PBAs cathode is poor electronic conductivity. The PBAs usually show low conductivity of 10−7‐10−11 S cm−1, causing large overpotential and worse electrochemical performance.[ 82 ] The common strategy to improve the electronic conductivity of PBAs is to combine them with highly electronic conductivity materials. Carbon materials such as CNT and graphene oxide (GO) with high conductivity are promising choices to improve the electrochemical performance of PBAs. The KFe[Fe(CN)6] was hybridized with CNTs to improve conductivity. With the 3D electronic conductivity network, the hybrid cathode showed a high capacity of ≈92 mAh g−1 at 0.2 A g−1.[ 83 ] Some conductive polymers have also been used for PBAs modification, such as pyrrole. Pyrrole can slow down the co‐precipitation rate of PBAs to improve crystallinity, and the in situ polymerization can construct a conductive poly‐pyrrole layer for high conductivity. The poly‐pyrrole coated PBAs cathode exhibited a high capacity of 108 mAh g−1 and longer lifespan.[ 84 ] Ion doping is another approach to improve the conductivity of PBAs. Compared with non‐Ni doping, K1.90Ni0.5Fe0.5[Fe(CN)6]0.89·0.42H2O showed a high initial capacity of 81.6 mAh g−1 with good capacity retention. The DFT calculations revealed that there was a decreased bandgap value of 1.32 eV after Ni‐doping, demonstrating higher electronic conductivity. As a result, K1.90Ni0.5Fe0.5[Fe(CN)6]0.89·0.42H2O | graphite full cell can achieve an energy density of 282.7 Wh kg−1.[ 85 ] The introduction of Fe vacancies via reconstruction in a hybrid electrolyte can also improve electronic conductivity. The K1.86Mn[Fe(CN)6]0.96·0.19H2O, activation in KNO3 and Fe(NO3)3 electrolyte, caused Mn2+ dissolution and Fe vacancies. DFT calculation revealed that there was a smaller bandgap in modified cathode compared with original cathode materials, indicating improved electronic conductivity.[ 86 ]
Low Density
Another disadvantage of PBA cathodes is their lower density. The density of PBAs is typically lower than that of LTMOs, limiting its energy density and volumetric energy density. Although the lower volumetric energy density will not significantly restrict the large‐scale application of PIBs in electric grids, it is necessary to optimize the density of PBAs for thinner electrodes, better wetting, and lower E/C ratio.
3.1.2. LTMO Cathode
Compared to PBAs, LTMOs show a higher tape density. However, the large‐scale application of LTMOs cathode is hindered by sluggish K+ diffusion and poor structure stability.
Sluggish K+ Diffusion
Due to the large size of K+ and multiple reaction plateau, the diffusion rate of K+ in LTMO cathodes is low. Increasing K+ concentration in the cathode can create more K+ diffusion channels, improving capacity and rate performance. Molecular dynamics simulation showed that higher K+ content in the cathode caused K+/vacancy disordered structure, creating continuous channels and more active storage sites for fast K+ diffusion. As a result, the higher K+ content cathode, K0.7Mn0.7Ni0.3O2 delivered better performance.[ 87 ] The higher K+ content P2/P3 K0.7Mn0.67Ni0.33O2 was obtained from electrochemical ion‐exchange. Compared with P2 K0.59Mn0.67Ni0.33O2 and P3 K0.68Mn0.67Ni0.33O2 cathode, the K0.7Mn0.67Ni0.33O2 cathode with high K+ content exhibited a high capacity of 116.3 mAh g−1 at 0.1 C and good rate performance (83.9 mAh g−1 at 2 C).[ 88 ] Element doping can modify local environment of K+ to improve conductivity. Compared with K0.45MnO2, the introduction of [Mn‐Co‐Mo]O6 octahedra into K0.45Mn0.9Co0.05Mo0.05O2 optimized the local electron structure and enlarged the interlayer spacing, facilitating the K+ diffusion to achieve a good capacity of 80.2 mAh g−1 at 100 mA g−1.[ 89 ] A similar mechanism was observed in P3 type K0.5Mn0.85Co0.05Fe0.05Al0.05O2 cathode. Al3+ doping expanded the interlayer space for K+ storage and mitigated the Jahn‐Teller effect by substituting Mn3+ in the structure, thereby enhancing structure stability. K0.5Mn0.85Co0.05Fe0.05Al0.05O2 cathode maintained a high capacity‐retention of 96.8 % after 300 cycles at 500 mA g−1.[ 90 ] Morphology adjustment can also improve reaction activation area to improve K+ diffusion. The homogeneous P2 K0.6CoO2 microcubes, prepared by a self‐templating strategy, provided a stable interface between the electrolyte and the active material. With a large active reaction area, the microcube cathode achieved high capacity of 87.2 mAh g−1 at 20 mA g−1 and 40 mAh g−1 at 5 C.[ 91 ] A single‐crystal P3 type K0.35Mn0.8Fe0.1Cu0.1O2 cathode, synthesized by bimetallic co‐induction effect, lacks grain boundaries, facilitating higher K+ diffusion. As a result, this cathode showed a superior rate performance of 52.9 mAh g−1 at 1000 mA g−1.[ 92 ] The coating strategy has also been employed to enhance the electrochemical kinetics of LTMOs. A layer of AlF3 was coated onto K1.39Mn3O6 microspheres to suppress side reaction between cathode and electrolyte, maintaining lower charge transfer resistance for fast K+ transport. Additionally, the high mechanical strength of coating layer buffered the structural changes during charge/discharge process. As a result, the AlF3@K1.39Mn3O6 cathode delivered 110 mAh g−1 at 10 mA g−1 and maintained a high capacity retention of 94.9% after 100 cycles.[ 93 ]
Poor Structure Stability
The Jahn‐Teller Effect is the main reason for the poor structure stability of LTMOs cathode. Jahn‐Teller Effect originated from the uneven distribution of electrons within the d orbitals will cause lattice distortion and worse lattice stability, further resulting in a short lifespan of LTMOs cathodes, Figure 2. For Mn‐based LTMOs, experiments indicated a high Mn average valence can suppress lattice distortion, leading to better performance. To achieve this, structural stabilizers like Mg2+ can be used to decrease trivalent Mn content, mitigating Jahn‐Teller Effect. Compared to Ti4+, the Mg2+ can improve Mn valence in K0.5Mn0.7Co0.2Fe0.1O2, leading to non‐split of eg orbitals and less Jahn‐Teller distortion. As a result, K0.5Mn0.6Co0.2Fe0.1Mg0.1O2 cathode showed high‐capacity retention of 74% after 500 cycles at 1 A g−1.[ 94 ] Using Zn2+ doping also can alleviate Jahn‐Teller effect. The presence of Zn2+ can stabilize energy of Mn‐O bond to improve structural stability of Mn‐based LTMOs. X‐ray absorption spectroscopy at the Mn K‐edge revealed that K0.5Mn0.8Co0.1Zn0.1O2 cathode showed higher Mn valance after Zn2+ doping. High angle annular dark field scanning transmission electron microscopy images indicated there was less (003) d‐spacing in K0.5Mn0.8Co0.1Zn0.1O2 cathode, proofing the presence of Mn4+ with less distortion and stable crystal structure in K0.5Mn0.8Co0.1Zn0.1O2 cathode. The weak Jahn‐Teller distortion is beneficial for less phase transition from P3 to O3 at high voltage. As a result, K0.5Mn0.8Co0.1Zn0.1O2 cathode delivered a high capacity retention of 89.8% at 100 mA g−1 after 100 cycles.[ 95 ]
3.1.3. Polyanion Cathode
Polyanionic materials usually show low electronic/ionic conductivity. For example, LiFePO4 shows ionic and electronic conductivity of 5 × 10−5 S cm−1 and 3.7 × 10−9 S cm−1, respectively, which limits the rate performance and low‐temperature performance of LiFePO4 cathode in LIBs.[ 96 ] In PIBs, the large K+ will further decrease the diffusion speed of K+ in polyanionic material, causing poor rate performance in PIBs, Figure 2. Using amorphous polyanionic materials is a useful strategy to improve K+ diffusion in polyanion cathode. The crystal FePO4 shows fewer channels for K+ diffusion, but there are open channels in amorphous FePO4 for K+ transport, resulting in a high initial capacity of 156 mAh g−1 at 5 mA g−1.[ 36 ] The amorphous FePO4 as a coating layer in LTMOs can improve K+ transport, achieving 3.86 × 10−11 cm2 s−1 diffusion coefficient at first charge process. This amorphous layer also can suppress strain stress to protect the stable interface in the cathode. Finally, the amorphous FePO4 coating LTMO cathode achieved a better rate performance of 65.7 mAh g−1 at 500 mA g−1, compared with 43 mAh g−1 in bare cathode.[ 97 ] Doping is also a good strategy to improve the diffusion rate in polyanionic materials. Cs+ is used to reduce the energy barrier of ion transfer and suppress volume change in KVPO4F, since the large Cs+ can expand the lattice layer for diffusion. K0.95Cs0.05VPO4F cathode showed a high capacity of 104.5 mAh g−1 at 20 mA g−1 and good capacity retention of 87.9% after 800 cycles at 500 mA g−1. The K0.95Cs0.05VPO4F | graphite full cell achieved 79.1% capacity retention after 2000 cycles at 300 mA g−1 and an energy density of 220 Wh kg−1.[ 98 ] In addition to the doping strategy, morphology control can also enhance the electrochemical performance of KVPO4F cathode. For carbon‐coated KVPO4F nanoplates, the porous nanoplates structure improves the contact between electrode and electrolyte, facilitating fast K+ diffusion. The carbon matrix enhances electronic conductivity and forms V‐F‐C bonds to protect structure for long cycling. The designed KVPO4F/C cathode exhibits 106.5 mAh g−1 at 0.2 C with a high operational voltage of 4.28 V (vs K/K+), and excellent rate performance (73.8 mAh g−1 at 100 C).[ 99 ]
In summary, element doping is a useful strategy to enhance conductivity and structural stability in PBAs, LTMOs, and polyanions cathodes. This strategy is also relatively easy to implement and conductive to industrialization. However, achieving a balance in electrochemical performance through doping is crucial. For instance, higher Ni content can increase operational voltage and discharge capacity of the cathode, but it may compromise structural stability, leading to a shorter lifespan.[ 100 ] Therefore, further research can focus on developing design guidelines of selecting dopant elements and optimizing their quantities in different cathode materials, enriching the strategies of cathode materials design. There is a high price of Co due to poor abundance and geopolitical, further increasing the cost of Co‐based cathodes. Consequently, doping strategies should also consider the cost of dopants, with low‐cost alternatives potentially improving the competitiveness of modified cathode materials. Morphology control is also a good strategy for cathode modification in PIBs, a large reaction area will facilitate reaction kinetics, but the nanotechnology will increase production complexity and increase cost. In addition to element doping and morphology modification, exploring other strategies to improve materials is also essential in future research, while issues of cost and feasibility should be considered when various strategies are proposed.
3.2. The Challenges and Strategies for the Development of Graphite Anode
Because of the low intercalation K+ potential (0.1 V vs K/K+), high capacity, low cost, abundant resource, and high CE, graphite is the most potential anode in PIBs. However, due to the large K+, the potassiation/depotassiation process will cause 60% volume change, leading to poor SEI and reduced structure stability. Although there is lower de‐solvation energy for K+, the small interlayer space of graphite can't achieve fast K+ diffusion, causing sluggish K+ reaction dynamic and poor rate performance, Figure 6 . The simulation results further confirmed that the kinetics of K+ intercalation was related to interlayer space; larger space can improve K+ diffusion dynamic.[ 101 ] Therefore, expanding the interlayer of graphite is a good strategy to improve the rate performance of graphite anode in PIBs. The expanded graphite with large interlayer spacing of 0.387 nm provided fast diffusion pathway for K+, leading to a high capacity of 263 mAh g−1 at 50 mA g−1, high CE, and better cycling stability.[ 102 ] Microcrystalline graphite, with larger interlayer spacing and abundant interparticle voids, is also a suitable choice for fast K+ intercalation, achieving a high capacity of 249 mAh g−1 at 100 mA g−1 after 100 cycles.[ 103 ] Except for designing expanded graphite for PIBs, exploring coating layer with fast K+ diffusion can also improve the performance of graphite in PIBs. A soft carbon coating layer, derived from PTCDA, on graphite with a larger interlayer space improved K+ transport in graphite and suppressed volume expansion. Therefore, this hybrid graphite anode showed better rate performance of 131.3 mAh g−1 at 2 C.[ 104 ] Using MoS2 as a coating layer for exfoliated graphite can enrich the K+ content on the surface of graphite, which boosts the K+ diffusion coefficient (up to 1000 times higher than that of bare graphite) and accelerates reaction kinetics. The MoS2/graphite exhibited a better rate performance of 125 mAh g−1 at 3.2 A g−1 (11 times better than the bare graphite).[ 105 ] HC with fast ions transport is also used as coating layers or mixed with graphite to modify its performance. For HC/graphite hybrid anode, HC facilitated K+ diffusion to improve K+ intercalation. As a result, this optimized anode achieved a higher reversible capacity of 305 mAh g−1 at 0.1 C and good capacity retention of 58.4% after 350 cycles at 2 C.[ 106 ] Heteroatom doping, which can change interlayer space and reaction kinetics, is also an effective strategy to improve performance of graphite anode. The sulfur/nitrogen doped graphite nanosheets showed a large interlayer of 0.39 nm and abundant defects/active sites, resulting in a high capacity of 142 mAh g−1 after 5000 cycles at 0.5 A g−1.[ 107 ]
Figure 6.

Comparison of potassiation process a) and lithiation process b) using graphite anodes. c) Summary of challenges for electrolyte design in PIBs, including slow K+ transfer in the graphite anode and solvent co‐intercalation in graphite, transition metal (TM) dissolution in electrolytes, unstable cathode structure and gas release in cathode side.
4. The Challenges and Strategies for the Development of Electrolytes in PIBs
The electrolyte, as a necessary component, significantly influence the electrochemical performance of PIBs. Similar to LIBs, electrolytes decompose at the electrode surfaces to generate a SEI and a cathode electrolyte interface (CEI) in PIBs. Poor SEI and CEI formation will cause issues such as solvent co‐intercalation, sluggish K+ movement, poor cathode structural stability, Figure 6. Therefore, it is important to design suitable electrolytes that promote stable interface layers on the electrode, suppress side reactions and improve cycling stability.
4.1. Electrolyte Design for SEI
The composition of SEI is closely linked to the solvated structure, making the selection of solvents and salts critical for determining its performance. For graphite anode in LIBs, the significant challenge is graphite exfoliation, which is typically mitigated by using ethylene carbonate (EC) as the solvent, as it generates a stable SEI in graphite anode. For other solvents, such as ether solvents, which show strong solvated ability, can co‐intercalate with Li+ into graphite, causing graphite exfoliation. However, the graphite anode shows good stability using ether electrolyte in PIBs, even at diluent concentration (1 m). In a 1 m KPF6 1,2‐dimethoxyethane (DME) electrolyte, the graphite anode exhibited an initial capacity of 108 mAh g−1, an ICE of 87.4%, and a low‐capacity fading rate of only 0.1% after 200 cycles. This contrasts with the performance in 1 m KPF6 EC/DMC (1:1, v/v), where the initial capacity is 135 mAh g−1 and decay rate is 2%.[ 108 ] However, using ether electrolytes show lower capacity and higher potassiation voltage, which will decrease energy density, some strategies are explored to improve that. Using the “steric hindrance” effect can reduce the solvated ability of solvents to regulate the solvated structure, achieving facile de‐solvation and K+ intercalation with lower potassiation voltage. The soft solvent, diethoxy methane (DEM), with a short intermediate carbon chain and longer terminal chain, can suppress “gauche effect” of liner ether to decrease solvated ability and achieve fast de‐solvation. Compared with the 2 m KFSI DME electrolyte, the 2 m KFSI DME/DEM electrolyte exhibited lower solvated energy, reduced de‐solvation energy, a high ICE of 82.3%, and a lower potassiation voltage. After decreasing the solvated ability, more anions can enter the first solvated sheath to form anion‐derived SEI for better performance. Finally, the K0.45Mn0.85Mg0.15Rb0.05O2 | graphite full cell using 2 m KFSI DME/DEM electrolyte can show a capacity of 57.7 mAh g−1 after 200 cycles with high capacity retention of 78.4%.[ 109 ] Similarly, diethylene glycol dimethyl ether (DGM) electrolyte, which incorporates a large intermediate carbon chain, can suppress solvents coordination, decreasing potassiation voltage in graphite anode. The DGM electrolyte can operate at 4.2 V (vs K/K+) and enable the graphite anode with a high average CE of 99.64 % during 200 cycles. And the methyl (‐CH3) group modification to organic solvents reduce toxicity and improve biosafety.[ 110 ] In addition to “steric hindrance” effect, modification of electron‐withdrawing group (F, Cl, and Br) can also decrease electron density to weaken solvated ability. These groups also reduce the least unoccupied molecular orbital (LUMO) level to achieve better oxidation stability. For example, 1,2‐bis(2‐chloroethoxy)ethane (DEECl) can exhibit oxidation stability up to 4.3 V (vs K/K+) and prevent Al corrosion. Using KFSI/DEECl electrolyte, the PBA | graphite full cell can run 6000 cycles with a high average CE of 99.98 %.[ 111 ] Another strategy to prevent solvents co‐intercalation is the use of high concentration electrolytes (HCEs) and localized high concentration electrolytes (LHCEs). The high concentration of salts in electrolytes can change the LUMO of electrolyte, leading to preferentially decomposition of salts and formation of anion‐derived SEI. And LHCEs, obtained from HCEs using non‐coordinated inert solvents as diluents, can maintain the original solvated structure. HCEs and LHCEs are very successful strategies for better performance in PIBs. For example, when using non‐polar and fluorinated solvents, 3‐methoxyperfluoro(2‐methylpentane) (MME) and 1,1,2,2,5,5,6,6‐octafluoro‐3‐oxahexane (OOE) as diluents in DME‐based HCEs, the LHCE exhibited lower de‐solvation energy and a lower potassiation voltage. Graphite | K cells using this LHCE extended cycling life to 2400 cycles with 93% capacity retention. The DME/MME/OOE‐based LHCE enabled K0.220Fe[Fe(CN)6]0.805·4.01H2O | graphite full cell to operate 100 cycles without capacity degradation.[ 112 ] Except ether solvents, carbonates solvents, such as EC, DMC, and DEC are also used in PIBs. In carbonates electrolytes, the potassiation mechanism is similar to Li+ in LIBs, but graphite anodes in PIBs using carbonate electrolytes experience more significant capacity fading compared to their LIB counterparts. This is mainly due to the large volume change of graphite during potassiation, which disrupts the original SEI and causes further SEI formation, consuming additional K+. Moreover, the SEI formed in carbonate‐based electrolytes for PIBs is less stable, leading to the accumulation of oligomer species during cycling. This thickens the SEI layer and impedes K+ transport.[ 113 ] Therefore, HCEs and LHCEs have also been explored in carbonated solvents to improve SEI stability and performance of PIBs. In PC‐based HCE, more aggregates and contact ion pairs in the solvated structure improve de‐solvation and prompt the formation of anion‐derived SEI, enhancing the electrochemical performance. Using PC‐based HCE, the graphite | K cells maintained a highly reversible capacity of 220 mAh g−1 for 6 months at 0 °C, and the K‐FeHCFe | graphite full cells showed long cycling life and wide operational temperature window.[ 114 ] With fast de‐solvation and stable SEI, PIBs using HCEs and LHCEs can achieve fast charging. In a 3 m KFSI EC/DEC electrolyte, PIBs demonstrated a high ICE of 95.7%, and the Prussian blue | graphite full cell achieved 103 mAh g−1 at 5 C, enabling fast charging with 80% of the capacity charged in just 13 min.[ 115 ]
Common salts used in PIBs are KBF4, KClO4, KPF6, KFSI, and KTFSI, but the KBF4 and KClO4 show lower solubility in most organic solvents, making the KPF6, KFSI, and KTFSI the preferred choices for electrolyte salts in PIBs. Salts have significant influence on the physicochemical properties of electrolytes, including ionic conductivity and electrochemical performance. Different salts dissociate to varying degrees in solvents, which impacts their ionic conductivity. Generally, KFSI salts with high dissociation show the highest ionic conductivity.[ 116 ] The PF6 − anion can passivate Al current collector to prevent current collector corrosion, but KPF6 has moderate solubility in carbonate solvents, limiting its use at HCEs. KPF6 shows poor high‐temperature stability and is easily decomposed by the moisture.[ 116 ] Imides based salts, such as KFSI and KTFSI, can achieve better solubility in organic solvents, but FSI− and TFSI− will combine with Al3+ to cause Al corrosion. Currently, there isn't salt can meet all requirement for optimal electrolytes in PIBs, therefore, the exploration of novel salt is also meaningful.
4.2. Electrolyte Design for CEI
Similar to the SEI, an interface layer is also formed between the cathode and electrolyte, called CEI. Generally, high oxidation stability is beneficial to generate a stable CEI, since electrolytes with poor oxidation stability will decompose at the cathode, producing radicals that can destroy the CEI. An unstable CEI fails to protect cathode stability, leading to metal dissolution and gas production. The dissolved metal can further catalyse electrolyte decomposition, accelerating battery failure. High oxidation stability can prevent radical generation, maintaining a stable interface and improving operational cut‐off voltage, specific capacity, and energy density. Therefore, much research focuses on designing electrolytes with higher oxidation voltage for stable CEI. The phosphates electrolytes such as trimethyl phosphate (TMP) and triethyl phosphate (TEP) with high anodic stability are suitable choices for high voltage electrolytes in PIBs.[ 117 ] However, phosphates electrolytes fail to stabilize the anode; therefore, more research focus on phosphate based HCEs and LHCEs. A non‐flammable LHCE consisting of tris (1‐propyl) phosphate (TTP), tris (2,2,2‐trifluoroethyl) phosphate (TFP), and 1,1,2,2,5,5,6,6‐octafluoro‐3‐oxahexane (OHE) showed less Al corrosion and better cycling stability in PIBs, and the iron‐based PBAs | graphite full cell using this LHCE achieved high‐capacity retention of 92 % after 200 cycles at 2 C with high operational voltage.[ 118 ] In KFSI TFP electrolyte, the fluorinated phosphate showed lower highest occupied molecular orbital (HOMO) for better oxidation stability. After fluorination, there is weak solvated ability in TFP, leading to formation of contact ion pairs/aggregates and anion‐derived SEI. This electrolyte enabled KVPO4F cathode to deliver a high‐capacity retention of 88.1% after 200 cycles with a high cut‐off voltage of 4.95 V (vs K/K+).[ 119 ] For sulfone electrolytes, the stronger electron withdrawing sulfonyl group lowers the energy level of the HOMO, leading to higher oxidation stability. The KFSI dimethyl sulfone (DMS) electrolyte can achieve better oxidation stability of ∼5.8 V (vs K/K+) and high ionic conductivity of 4.0 × 10−4 S cm−1 at 25 °C.[ 120 ] But sulfone electrolytes also fail to achieve stable SEI in the anode, and they are usually used as non‐flammable and high oxidation stability additives.
Currently, much research is focused on electrolyte design for PIBs, while progress has been made, these advances are still far from industrial application. Ether electrolytes show good cathodic stability in PIBs due to high LUMO (Figure 7a), and their low melting point can enable good performance at low temperature. However, poor anodic stability limits their use with high‐voltage cathodes. Ester electrolytes (carbonate, phosphate, and sulfone), which have good oxidation stability, show unstable SEI formation at the anode, Figure 7a. For HCEs and LHCEs, there are stable SEI, high anodic stability, safety, and better lifespan, but their high cost remains a significant challenge, Figure 7b. For LHCEs, using diluents can decrease salt concentration in HCEs to form a normal concentration electrolyte (1 m). However, commonly used hydrofluoroether diluents, such as bis(2,2,2‐trifluoroethyl) ether and 1,1,2,2‐tetrafluoroethyl‐2,2,3,3‐tetrafluoropropyl ether, are highly expensive, meaning LHCEs can not necessarily reduce electrolyte costs. Many literatures have focused on low‐cost diluents in PIBs, with some suggesting that hydrofluoroethers pose a low environment risk, including zero stratospheric ozone depletion and relatively low global warming potential.[ 121 ] Therefore, exploring low‐cost hydrofluoroethers is a suitable strategy for electrolyte design to achieve a balance between cost and high electrochemical performance. HCEs and LHCEs show low ionic conductivity, which hampers fast charging. Using the soft solvents with lower solvated ability can improve K+‐anions interaction, leading to stable SEI formation at lower concentrations and reducing costs. But the low salts dissociation in soft solvents also causes low ionic conductivity. Learning from the development of electrolytes in LIBs, single solvents and single salts can't meet all requirements of future electrolyte in PIBs, future electrolytes exploration may focus on multi‐solvents/salts research.
Figure 7.

a) Summary of current electrolyte design strategies including solvent molecules design, salts concentration adjustment, and additives (HCEs: high concentration electrolytes, LHCEs: localize high concentration electrolytes, highest occupied molecular orbital (HOMO) and least unoccupied molecular orbital (LUMO) energy level of different kind of solvents) b) Advantages (yellow box) and disadvantages (purple box) of HCEs/LHCEs and soft solvent electrolyte or weakly solvent electrolyte. (IC: ionic conductivity, EW: electrochemical windows).
5. The Challenges and Strategies for Developing Full Cells
Half‐cells are typically used for research and materials development in PIBs, while the full cell is the final product for practical applications. The main difference between half‐cell and full cell is the limited availability of K+ in full cell, which comes from the cathode materials. During cycling, the SEI formation and CEI generation will consume K+, causing a lower reversible capacity and lower energy density. In half‐cells, the abundant K+ helps compensate for the loss of K+, resulting in better performance. Consequently, half‐cells generally exhibit better electrochemical performance than full cells, even when the same cathode materials are used.
To offset K+ loss in SEI/CEI formation, the strategy of extra K+ compensation has been proposed to improve the performance of full cells in PIBs. One strategy for K+ compensation is to pre‐intercalate K+ in the anode, Figure 8 . A pre‐potassiated alloy anode Bi/P/CNT was obtained from chemical potassiation in potassium‐biphenyl and DME solution, which showed high ICE of 96.2% and a high irreversible capacity of 403 mAh g−1. Finally, the pre‐potassiated Bi/P/CNT anode showed high‐capacity retention of 0.031% after 700 cycles at 1.5 A g−1.[ 122 ] Using the pre‐potassiation strategy, the KC8 graphite anode was fabricated in a roll‐to‐roll method. The KC8 foil showed a high areal capacity of 1.49 mAh cm−2, and the PTCDA | KC8 full cell achieved capacity retention of 84.1% after 100 cycles at 30 mA g−1.[ 123 ] Another approach, using self‐sacrificial additive for K+ compensation would be easier and safe. In full cell, the K+ is only from cathode materials, and these K+ contained self‐sacrificial additives will be decomposed to provide extra K+ for cycling. For example, dipotassium squarate (K2C4O4) was used as a low‐cost and high‐efficiency K+ compensation resource. The K2C4O4 was decomposed at 3.7 V (vs K/K+) to generate more K+ for higher reversible capacity, higher capacity retention, and longer lifespan. With the help of K2C4O4, the K0.5MnO2 cathode delivered a higher ICE of 93.5%, and better capacity retention of 91.6% after 300 cycles. K0.5MnO2 | soft carbon full cell achieved a high energy density of 220 Wh kg−1 and longer lifespan.[ 124 ] Both pre‐potassiation and self‐sacrificial additive strategies can achieve K+ compensation, Figure 8, but chemical pre‐potassiation methods typically need highly reactive potassium sources to offset the initial K+ loss, causing complex processes and high risk. The use of self‐sacrificial additive can simplify the produced process, and the small amount of self‐sacrificial additive used in the cathode will not significantly increase cost. However, the decomposition of self‐sacrificial additive may induce by‐product and gases, resulting in safety issue. The extra K+ from self‐sacrificial additive may deposit at the anode if K+ exceeds the maximum capacity of the anode, causing K metal deposition and lower CE. K+ compensation is a good strategy to improve performance in full cell of PIBs, but how to optimize these methods to promote the commercialization of PIBs still needs to be explored.
Figure 8.

Summary of K+ compensation strategies in full cell: pre‐potassiation and self‐sacrificial additives.
6. Practical Considerations for the Real Applications of PIBs
Indeed, material development alone is not sufficient for the successful commercialization of PIBs. Cost‐effectiveness, practicality, and scalability are also essential factors for their industrialization.
6.1. Cost from Raw Materials to Practical Battery Applications
Recently, with the fast development of electric vehicles (EVs), the price of Li2CO3 has increased significantly. And because Li resources are limited, subsequent exploitation of Li mineral resources requires more advanced exploitation technology and longer supply chains, which will cause the price of Li raw materials to rise rapidly. All of these will result in an increase in the price of LIBs, which may hinder the widespread adoption of green energy technologies. Abundant K resources can maintain the price of raw materials relatively low and stable as shown in Table 1, thereby reducing the production cost of cathode and salts for PIBs. The high‐cost Cu current collector can be replaced by low price Al current collector in the anode side (600 $ m−2 for Al foil, and 1100 $ m−2 for Cu foil, all foils thickness are 16‐20 um), since the K will not form alloy with Al, therefore, the use of Al current collector for both anode and cathode can further reduce battery manufacturing costs.[ 11 , 125 ] And for industrialization, the cost is not just from raw materials, the cost for large scale preparation should be considered. For the cathode materials in PIBs, there are usually three prepared methods: high‐temperature calcination, hydrothermal reaction, and co‐precipitation nucleation. Both high‐temperature calcination and hydrothermal reaction are easily controlled processes that can be scaled up for industrial applications by simply increasing the size of the reaction vessels. For LTMOs, the preparation method is similar to that of cathode in LIBs, therefore, the existing LTMOs preparation production line for LIBs can be used to promote the development of LTMOs cathode materials in PIBs, potentially decreasing cost of large‐scale preparation in PIBs. However, the K‐based LTMOs are more sensitive to moisture than Li‐based LTMOs, which may increase the additional cost to the preparation method. Co‐precipitation for PBAs preparation is an environmentally friendly, low‐energy process, making it an attractive option for industrialization. However, the performance of PBAs is influenced by the size and morphology of the crystal, precise control of reaction conditions, such as temperature and time, may add additional costs. The production of graphite anode can be sourced from the existing graphite production lines in LIBs, which can further reduce industrialization costs and accelerate the industrialization of PIBs.
To assess the commercialization potential of PIBs, both their energy density and estimated cost are analyzed and discussed. Energy density of various batteries are shown in Figure 9 . It is evident that LIBs have higher energy density compared to PIBs and SIBs. This is primarily due to LIBs’ higher operational voltage and their high‐capacity cathodes. For PIBs and SIBs, their energy density largely depends on the cathode materials used. The K2Mn[Fe(CN)6] cathode, with a high capacity of 155 mAh g−1, can deliver a relatively high energy density of 165 Wh kg−1 when paired with a graphite anode. However, for SIBs, the operational voltage is often lower due to the use of HC anodes, which results in reduced energy density. From Figure 9, it can be also seen that most of the cathode materials of PIBs and SIBs show lower cost compared to that of LIBs, e.g. 15 $ kg−1 for LiFePO4,[ 126 ] 23.8 $ kg−1 for LiCoO2,[ 126b ] 21.5 $ kg−1 for LiNi0.8Mn0.1Co0.1O2 (NMC811),[ 127 ] 10.7 $ kg−1 for K2Mn[Fe(CN)6],[ 128 ] 10.5 $ kg−1 for K2Fe[Fe(CN)6], 8.8 $ kg−1 for KFeSO4F, 11.2 $ kg−1 for K0.5MnO2, 18 $ kg−1 for Na3V2(PO4)2F3, and 10.5 $ kg−1 for Na2Mn[Fe(CN)6].[ 129 ]
Figure 9.

a) Calculated energy density of various batteries system and cost of cathode materials. b) Cost of various batteries system for high energy pack‐batteries (100 kWh as target energy). (LFP: LiFePO4, Gr: graphite, LCO: LiCoO2, NMC811: LiNi0.8Mn0.1Co0.1O2, KMFCN: K2Mn[Fe(CN)6], KFFCN: K2Fe[Fe(CN)6], KFSF: KFeSO4F, KMO: K0.5MnO2, NVPOF: Na3V2(PO4)2F3, NMFCN: Na2Mn[Fe(CN)6], HC: hard carbon).
The estimated cost of various battery packs was calculated based on 100 kWh. The energy cost was calculated using the fellow equation:
| (1) |
Where the mass of active materials was estimated to account 45% of total battery weight, and the cost of anode and cathode was estimated to make up 50% of total battery cost. Canode and Ccathode are specific capacity of anode and cathode, respectively.
Although LIBs have higher energy density and the ability to achieve the target energy levels with fewer materials, their high cost of raw materials makes them relatively expensive. This presents a significant barrier to their widespread application in large‐scale electric grids storage. In contrast, PIBs benefit from the use of low‐cost raw materials, particularly for the cathodes, making them more cost‐effective. While PIBs may not yet match the energy density of LIBs, their lower material costs allow them to achieve competitive energy performance at a reduced cost. Among all batteries, the estimated lowest cost is for the K2Mn[Fe(CN)6] | Gr batteries at 44.3 $ kWh−1, followed by KFeSO4F | Gr at 55.3 $ kWh−1. For polyanion cathodes like KFeSO4F, their high operational voltage and cheap raw materials contribute to achieving low‐cost, high‐energy battery pack. The Na2Mn[Fe(CN)6] system also offers a similarly low cost of 54.6 $ kWh−1. Therefore, based on the above analysis, it is evident that PIBs and SIBs offer substantial cost advantages compared to LIBs. The K2Mn[Fe(CN)6] | Gr system, in particular, stands out for its potential to achieve both high energy density and reduced costs, making it a strong candidate for future large‐scale applications. PIBs, especially with low‐cost materials like K2Mn[Fe(CN)6], represent a promising pathway for achieving affordable, efficient, and sustainable energy storage systems.
6.2. Advantages for Large‐Scale Applications
Although PIBs are unlikely to compete with LIBs for high‐energy applications such as portable electronics and EVs, they are likely to find opportunities in low‐range EVs and grid‐scale storage. In addition to PIBs, there is also a rapid development for other low‐cost energy storage batteries such as ZIBs and SIBs, but PIBs still have their own advantages, Figure 10 . For the cost of raw materials, 150 $ ton−1 for ZnS, 100 $ ton−1 for Na2CO3, and 250 $ ton−1 for K2CO3 much lower than the price of Li2CO3 (26 400 $ ton−1), Table 1.[ 11c ] The abundant resources of Na and K are sufficient for large scale grids, ensuring a stable demand‐supply relationship, but Zn is less abundant than Na and K, Table 1.[ 10a ] In ZIBs, Zn metal is used as an anode, while in SIBs and PIBs, carbon materials (HC for SIBs and graphite for PIBs) are the promising anode. The cost of graphite and HC is 2300 and 1500 $ ton−1, respectively, which is lower compared to 4400 $ ton−1 for Zn metal.[ 130 ] The current collector used in ZIBs is stainless‐steel which shows better resistivity and lower price than other commonly used current collectors (Al, Cu), reducing the cost for the current collector (400 $ m−2 for stainless‐steel foil). But the heavy stainless‐steel (density of stainless‐steel, Cu, and Al: 7.5 g cm−3, 8.96 g cm−3, and 2.7 g cm−3) will further decrease the energy density of ZIBs. The Zn has a higher equilibrium potential of ‐0.76 V vs SHE; therefore, the aqueous electrolytes can be used. Compared to aqueous electrolytes, organic electrolytes commonly used in SIBs and PIBs are more expensive (e.g., the price of organic solvents such as DME is 200 $ L−1 and diglyme costs 313 $ L−1, while ultrapure water is priced at 120 $ L−1).[ 131 ] Additionally, organic electrolytes are flammable and less environmentally friendly. However, the organic solvents show wide electrochemical windows, while narrow electrochemical windows of water causes serious hydrogen evolution reactions in aqueous electrolytes for ZIBs, which can negatively affect lifespan. Zn‐salts are much cheaper than K salts and Na salts. For instance, the prices of ZnCl2 and ZnSO4 are 0.5 and 0.62 $ g−1, respectively, while KFSI costs 8 $ g−1 and NaPF6 is priced at 6.5 $ g−1),[ 131 ] but the high permittivity and high donor number of water allow superior solubility for salts in ZIBs, for example water‐in‐salt electrolytes. The HCEs can hinder water decomposition and improve electrochemical performance in ZIBs, but the high cost of HCEs reduces the competitive advantage of ZIBs. Although HCEs are also used for PIBs and SIBs, the concentration varies from 3‐5 m due to low permittivity of organic solvents. Currently, the diluents can be used in organic HCEs to decrease concentration in the electrolyte, and some cheap diluents can decrease cost of electrolytes in PIBs and SIBs. However, there are not suitable diluents for HCEs in ZIBs, because most diluents are miscible with water. In addition to the cost of raw materials, PIBs and SIBs are highly sensitive to air, requiring controlled environments during both electrode material preparation (such as temperature and humidity control) and battery assembly (often performed in an Argon‐filled glove box). Furthermore, the production of PIBs and SIBs involves the use of many organic solvents in preparation processes. The disposal of these solvents inevitably increases costs, contributing to the higher price of the final product. In contrast, ZIBs can be assembled in the air, and their use of aqueous electrolytes makes them more environmentally friendly. However, ZIBs have lower energy density compared to PIBs and SIBs. There are different equilibrium potentials for three metal electrodes, the K of ‐2.92 V (vs SHE), Na ‐2.71 V (vs SHE), and Zn ‐0.76 V (vs SHE). The lower electrode potential of K can improve operational voltage to achieve high energy density. The graphite can be used in PIBs with lower intercalation voltage, but Na+ can't be stored in the graphite. The use of HC anode in SIBs will decrease the operational voltage, thereby decreasing energy density. Therefore, PIB is the best choice for low‐cost and high‐energy‐density energy storage systems.
Figure 10.

Comparison of cost of PIBs, SIBs, and ZIBs in terms of electrolyte cost, electrode cost, current collector cost, and energy density. (In electrolyte cost, diglyme and NaPF6 for SIBs, DME and KFSI for PIBs, ultrapure water and ZnCl2 for ZIBs used for comparison;[ 131 ] In electrode cost, Na3V2(PO4)2F3, hard carbon, K2Mn[Fe(CN)6], graphite, MnO2, Zn metal used for comparison.[ 128 , 129 , 132 ] Al: aluminum current collector, SS: stainless‐steel current collector).
6.3. Challenges During Scale‐Up
Although PIBs show significant potential as next‐generation batteries, several challenges remain for their commercialization.
While potassium is abundant and relatively inexpensive, the availability of high‐purity potassium raw material for production of K‐salts and cathode materials remains limited, which could hinder the scale‐up of PIBs. The performance of cathodes is highly dependent on their morphology and synthesis methods. For example, the crystallinity of PBAs, influenced by factors such as solvents environment, temperature, and nucleation time, plays a critical role in determining their electrochemical performance. Developing scalable and cost‐effective methods to produce high‐performance electrode materials is crucial for large‐scale production. Commonly used ether‐ and ester‐based electrolytes struggle to simultaneously achieve high ionic conductivity, high‐voltage stability, and effective SEI formation. This leads to low operational voltage, poor cycle life, and reduced energy density in full cells. Additionally, safety and environmental concerns surrounding organic electrolytes is also a challenge during scale‐up. Due to the large size of K+, PIBs undergo greater volume changes compared to LIBs. This increased expansion accelerates performance degradation. Side reactions such as electrolyte decomposition, gas evolution, and electrode dissolution, undermine the cycling stability and shorten the lifespan of PIBs. Overcoming these issues through advanced electrode and electrolyte design is essential for improving scalability. The transition from laboratory‐scale to industrial‐scale manufacturing also introduces challenges related to consistency, quality control, and process optimization. Ensuring uniformity in cathode materials, electrode fabrication, and electrolyte formulation, while addressing scalability issues in equipment and preparation process, adds significant complexity to the scale‐up process. Ensuring the safe operation of PIBs presents another challenge for large‐scale application. PIBs exhibit lower volumetric energy density due to the lower density of their cathodes compared to LIBs. Large batteries pack require more stringent temperature control and monitoring to ensure the uniform temperature distribution across the entire pack. This is essential to prevent localized overheating, which could result in thermal runaway and safety concerns.
7. Development of Techniques for Understanding the Mechanism of PIBs
With the development of PIBs, more advanced techniques are used in PIBs for deep mechanism exploration, such as, XRD, neutron powder diffraction (NPD), X‐ray absorption spectroscopy (XAS), atomic force microscopy, transmission X‐ray microscopy, Raman, solid nuclear magnetic resonance and so on. For real‐time reactions and mechanisms, in situ techniques are increasingly essential for understanding the underlying processes and facilitating the development of PIBs. In situ TEM is effective to observe the structural changes at the atomic level, enabling real‐time monitoring of interface formation and providing insights into the formation and evolution of the SEI/CEI. In situ XRD, NPD, and XAS provide valuable information on the crystallographic and local structural changes occurring within the electrode materials during charge/discharge process. These techniques shed light on the mechanism of energy storage and identify the cause of battery failure, such as structural degradation, phase instability, and side reaction. Therefore, the development of batteries is closely tied to advancements in various characterization technologies. For future in situ technologies, enhancing the time and spatial resolution capabilities of techniques is crucial for accurately capturing the dynamic changes of batteries during charging/discharging process. High resolution technologies enable precise tracking of transient phenomenon, such as SEI formation and phase changes. Current single in situ characterization methods are insufficient to fully explore mechanism in batteries. Multifunctional characterization, which combines various in situ techniques, should be employed to achieve a comprehensive understanding of battery performance. For example, integrating TEM, XRD, and XAS can gain a better understanding of structural, chemical, electrochemical changes during operation. Additionally, combining in situ characterization with artificial intelligence technologies to process and analyze large datasets will help to uncover meaningful insights into battery mechanisms. While theoretical calculations are different from experiments, theoretical simulation can analyze the various reaction paths and energies to provide guidance for battery design. The integration of experimental and computational data could accelerate the development of PIBs.
8. Summary and Prospect
PIBs are a promising candidate for large scale electric grids, due to their abundant resources, low cost, and suitable energy density. Over the past decade, research for PIBs has made great progress, including cathodes, anodes, and electrolytes. For the cathode, there are several potential candidates. PBAs cathode can achieve fast charging and higher capacity, but how to control the water content in the crystal to improve performance is still a challenge. LTMO cathodes show higher operational voltage and higher energy density, but the dissolution of transition metal causes an unstable interface and poor structure stability. Polyanion cathodes show high redox potential, but the poor electronic conductivity limits its rate performance. For the anode, graphite with lower intercalation potential, high CE, less volume expansion, and low cost is the best choice for PIBs. But how to improve cycling stability and rate performance also needs more effort. Various strategies, including nanotechnology, morphology control, surface modification, and element doping, are proposed to prompt electrochemical performance of electrode materials. Research on electrolytes has also made great progress, and many strategies have been proposed to improve the performance of electrolytes, such as the design of solvent molecules and diluents, HCEs/LHCEs, and different kinds of additives. However, all these progresses are still in the academic research and tested under half‐cell. More efforts are needed to explore the deep mechanism and prompt commercialization of PIBs, and some possible directions are outlined for future research of PIBs, Figure 11 .
Figure 11.

Summary of potential directions for future research on the industrial application of PIBs, including high energy density, safety, fast charge, and wide temperature operation.
8.1. Full Cell
In the half‐cell, the abundance of K+ can compensate for the loss of K+ in the side reaction, achieving better performance. In other words, the half‐cell will cover up the disadvantages of electrode materials and get better performance. However, the limited K+ will be consumed quickly in the full cell, leading to fast capacity fading. Therefore, the focus of research should be switched from half‐cell to full cell. In Table 2 , the “high” energy density is calculated based on electrode materials from full cell, however, the actual electrochemical performance still falls short of meeting commercial requirements. To improve the commercialization of PIBs, future full cell testing should be conducted under more practical conditions, such as higher mass loading, lower E/C ratio, and lower negative/positive electrode capacity (N/P) ratio, Figure 11. For example, Group1.ai has launched an 18650 PIBs cylindrical cell using KxMn[Fe(CN)6] as the cathode and graphite as the anode. Due to its high operational voltage and capacity, this commercial PIB can deliver an energy density comparable to that of LFP (130–180 Wh kg−1).[ 143 ] Therefore, testing under practical conditions is essential for accurately assessing the commercialization potential of PIBs. Research about full cell fabrication technology and testing conditions such as formation time and depth of discharge are also necessary for the successful application of PIBs.
Table 2.
Comparison of PIB full cell performance.
| Capacity [mAh g−1] | Voltage (vs. K/K+) | electrolyte | Energy density [Wh kg−1] | |
|---|---|---|---|---|
| K2Fe[Fe(CN)6] | graphite[ 133 ] | 67 at 50 mA g−1 (after 500 cycles) | 2.0 ‐ 4.5 | 0.8 m KPF6 EC/DEC | 272 (based on cathode) at RT |
| KMO | graphite[ 134 ] | 56 at 100 mA g−1 (after 100 cycles) | 1.0 ‐ 3.5 | 1mKFSI FTEP | N/A |
| KFeC2O4F | soft carbon[ 135 ] | 85 at 0.1 A g−1 (after 200 cycles) | 1.7 ‐ 4.4 | 1mKPF6 in EC/PC (1:1, v/v) | 235 (based on cathode) at RT |
| K0.5MnO2@ K2C4O4 | soft carbon[ 124 ] | 88 at 0.01 A g−1 (after 100 cycles) | 0.5 ‐ 4.0 | 0.8mKPF6 in EC/DEC (1:1, v/v) | 158 (based on cathode and anode) at RT |
| KNiHCF | graphite[ 136 ] | 54 at 500 mA g−1 (after 500 cycles) | 1.5 ‐ 4.0 | 1 M KPF6 DEGDME | 96.54 (based on cathode and anode) at RT |
| K2Mn[Fe(CN)6] | graphite[ 137 ] | 120 at 20 mA g−1 (after 300 cycles) | 1.5 ‐ 4.2 | 2.5mKFSI TEP | 331.5 (based on cathode and anode) at RT |
| K‐FeHCFe | graphite[ 114 ] | 85 at 200 mA g−1 (after 1000 cycles) | 2.0 ‐ 4.2 | 4mPC KFSI | 245.5 (based on active materials) at RT |
| PTCDA | graphite[ 138 ] | 96.2 at 100 mA g−1 (after 100 cycles) | 0.5 ‐ 3.5 | 1mKFSI TMP/DME/DX | N/A |
| K3(VO)(HV2O3)(PO4)2(HPO4) | polyaniline‐intercalated layered titanate[ 139 ] | 54 at 100 mA g−1 (after 600 cycles) | 2.0 ‐ 4.8 | 1mKPF6 in EC/PC (1:1, v/v) | 236 (based on active materials) at RT |
| PTCDA | graphite[ 140 ] | 105.9 at 130 mA g−1 (at ‐20 oC after 100 cycles) | 1.0 ‐ 3.5 | 1mKFSI MTHF | 197 (based on cathode) at ‐20 oC |
| K1.72Fe[Fe(CN)6]0.96·0.342H2O | graphite[ 141 ] | 96.7 at 100 mA g−1 (after 100 cycles) | 1.4 ‐ 4.2 | 5mKFSI EGDE | 216.7 (based on cathode) at RT |
| K0.35Mn0.8Fe0.1Cu0.1O2 | graphite[ 92 ] | 77.3 at 100 mA g−1 (after 300 cycles) | 0.5 ‐ 3.5 | 3mKFSI EC/DMC/EMC (1:1:1, v/v/v) | 142 (based on cathode) at RT |
| K0.95Cs0.05VPO4F | graphite[ 98 ] | 75.6 at 300 mA g−1 (after 2000 cycles) | 2.0 ‐ 5.0 | 1mKPF6 EC/DEC (1:1, v/v) + 2 wt% FEC | 220 (based on cathode and anode) at RT |
| K0.5MO2 | soft carbon[ 142 ] | 60 at 20 mA g−1 (after 20 cycles) | 1.0 ‐ 4.0 | 0.8mKPF6 EC/DMC (1;1, v/v) + 0.7 % LiDFOB | 167.3 (based on cathode and anode) at RT |
| KxMn[Fe(CN)6] | graphite[ 143 ] | – | 2.5 ‐ 4.5 | 130‐180 (total weight) | |
| LiFePO4 | graphite[ 144 ] | 2000 at 0.05 C (after 800 cycles) | 2.75 ‐ 4.2 (V, vs Li/Li+) | – | 120‐140 (total weight) |
| Na‐PBAs | HC[ 145 ] | – | – | – | 160 (total weight) |
8.2. Safety
Safety is a significant concern for most non‐aqueous electrolytes. Thermal runaway, caused by short‐circuit, can lead to self‐heating of the battery and ignite the flammable organic electrolytes, causing an explosion, Figure 11. Research aimed at addressing safety issues mainly focuses on electrolyte design. Using phosphate and fluorinated solvents as electrolytes or additives can improve safety, because the P and F atom act as radical scavengers, neutralizing OH· and O· radicals and preventing electrolytes combustion. However, phosphate solvents fail to passivate anode and are typically used as additives in electrolytes of PIBs. Increasing salt concentrations in phosphate solvents can alter the solvated structure and promote anion‐derived SEI formation for better electrochemical performance. The fluorination of solvents is also an effective strategy to achieve stable performance and enhanced safety. The F atom can also clear OH· and O· radicals, and the fluorination group can modify solvated structure to ensure stable SEI. Additionally, fluorination improves the oxidation stability of the electrolyte. But the fluorinated electrolytes will weaken the salts dissociation, which lowers ionic conductivity. The complex synthesis process will also increase the cost. Therefore, future research could focus on addressing the negative effects of fluorinated electrolytes to prompt the development of better electrolyte design. In addition to liquid electrolytes, (quasi) solid state electrolytes offer a solution by eliminating the use of flammable electrolytes, improving safety. The use of (quasi) solid state electrolytes can prompt the development of K‐metal batteries with higher energy density; therefore, the exploration of (quasi) solid state electrolytes is a promising direction for next generation batteries.
8.3. Wide Temperature Operation
The future commercialization of PIBs for grid‐scale energy storage also requires operation across a wide temperature range, from ‐30 °C to 50 °C, Figure 11. The electrochemical performance of PIBs faces challenges in extreme temperature environments, due to the freezing or volatility of electrolytes. Through adjusting the electrolyte concentration, introducing additives, or tuning the solvents, the operating temperatures range of PIBs may be extended. However, other physical properties of electrolyte, such as ionic conductivity, viscosity, cost, chemical stability, and thermal stability should be properly evaluated. In addition, further investigation of the solvated structure in electrolytes is also important for deeper understanding of their interfacial behavior on electrodes during variable temperature operation. At low temperature, the ions de‐solvation is the main energy consuming process, K+ with lower de‐solvation energy is easy to achieve intercalation. Therefore, the LHCEs and soft electrolytes, which exhibit lower de‐solvation energies, typically achieve better low‐temperature performance, even though these electrolytes may have lower ionic conductivity. At high temperature, PIBs with LHCEs and soft electrolytes also can deliver good performance, but the high volatility of these solvents (ethers and perfluoro‐ethers) may cause pouch cell bulging and poor lifespan, hindering its large‐scale application. To develop better all‐temperature operational electrolytes, more attention should be paid on the evolution of solvated structure and behavior of SEI/CEI at various temperatures.
8.4. Fast Charging
PIBs with adequate energy density can also be used for short‐range EVs and public transport. Therefore, designing fast charging PIBs is also important to increase their competitiveness, Figure 11. Current research on fast charging mainly focuses on electrolyte design, aiming to improve ionic conductivity and facilitate ions de‐solvation at the interface. However, many literatures have confirmed that a stable SEI can also improve rate performance, even with lower ionic conductivity. The impact of SEI components on interface kinetics is also worthy of attention. In addition to electrolyte design, electrode materials optimization can improve rate performance. For example, surface modification of graphite can facilitate ions de‐solvation, achieving fast charging. Future research on fast charging should not only prioritize electrolyte design but also explore improvements in electrode materials.
In conclusion, the PIBs represent a promising low‐cost energy storage device for electric grid applications. Over the past decade, significant progress has demonstrated their great potential for commercial applications, driving continued efforts toward their commercialization. However, current study of PIBs on addressing their practical challenges is lagging, and requires further advancement. This review primarily focuses on evaluating the challenges associated with PIBs and strategizing solutions to overcome these challenges in the context of their industrial implementation. We hope that this comprehensive summary of the past decade's efforts, along with the future outlook based on our understanding of how to address the existing shortcomings, would accelerate progress toward their real applications in the near future.
Conflict of Interest
The authors declare no conflict of interest.
Acknowledgements
Financial support from the Australian Research Council (FT230100598 and FL210100050) is acknowledged. M.L. acknowledges the Chinese Scholarship Council for scholarship support (No. 202106130006).
Open access publishing facilitated by The University of Adelaide, as part of the Wiley ‐ The University of Adelaide agreement via the Council of Australian University Librarians.
Biographies
Mingnan Li received his Bachelor's and Master's degree in 2018, and 2021 from Hunan University, China. He is a currently a Ph.D. candidate at The University of Adelaide, under the supervision of Prof. Zaiping Guo and Dr Jianfeng Mao. His research is focused on the design of electrolytes for Li metal batteries, as well as electrolyte/electrode interface optimization.

Jianfeng Mao is an associate professor, ARC future fellow, Clarivate Highly Cited Researcher and the Discipline Lead in materials engineering at the School of Chemical Engineering, The University of Adelaide. His current research interests are in developing advanced electrolytes and materials for next‐generation batteries, as well as the green battery recycling methods for promoting the sustainability of battery supply chain. He has published over 120 papers (70+ as the first or corresponding author) in the leading discipline journals, such as J. Am. Chem. Soc., Angew. Chem., Adv. Mater., Energy Environ. Sci., Nat. Commun., Sci. Adv., and so on.

Zaiping Guo is an ARC Australian Laureate fellow, fellow of Australian Academy of Science, and fellow of Australian Academy of Technological Sciences & Engineering at The University of Adelaide. Her research focuses on the design and application of electrode and electrolyte materials for energy storage and conversion, including rechargeable batteries, hydrogen storage, and fuel cells. Her research achievements have been recognized through numerous awards, including NSW Premier's Prizes for Science & Engineering (2020), ARC Queen Elizabeth II Fellowship (2010), ARC Future Fellowship (FT3, 2015), ARC Laureate Fellowship (2021), and the Clarivate Analytics Highly Cited Researcher Award since 2018.

Li M., Wang C., Wang C., et al. “10 Years Development of Potassium‐Ion Batteries.” Adv. Mater. 37, no. 46 (2025): 2416717. 10.1002/adma.202416717
Contributor Information
Jianfeng Mao, Email: jianfeng.mao@adelaide.edu.au.
Zaiping Guo, Email: zaiping.guo@adelaide.edu.au.
References
- 1. Li M., Lu J., Chen Z. W., Amine K., Adv. Mater. 2018, 30, 1800561. [DOI] [PubMed] [Google Scholar]
- 2. Mohr S. H., Mudd G. M., Giurco D., Minerals 2012, 2, 65. [Google Scholar]
- 3.a) Li G., Sun L., Zhang S., Zhang C., Jin H., Davey K., Liang G., Liu S., Mao J., Guo Z., Adv. Funct. Mater. 2024, 34, 2301291; [Google Scholar]; b) Mao J., Zhou T., Zheng Y., Gao H., kun Liu H., Guo Z., J. Mater. Chem. A 2018, 6, 3284; [Google Scholar]; c) Zhang W., Liu Y., Guo Z., Sci. Adv. 2019, 5, aav7412; [DOI] [PMC free article] [PubMed] [Google Scholar]; d) Mao J., Wang C., Lyu Y., Zhang R., Wang Y., Liu S., Wang Z., Zhang S., Guo Z., J. Mater. Chem. A 2022, 10, 19090. [Google Scholar]
- 4. Zhang Q., Wang Z., Zhang S., Zhou T., Mao J., Guo Z., Electrochem. Energy Rev. 2018, 1, 625. [Google Scholar]
- 5. Sun L., Li G., Zhang S., Liu S., Yuwono J., Mao J., Guo Z., Sci. China Chem. 2024, 67, 4. [Google Scholar]
- 6. Cao B., Zhang Q., Liu H., Xu B., Zhang S., Zhou T., Mao J., Pang W. K., Guo Z., Li A., Adv. Energy Mater. 2018, 8, 1801149. [Google Scholar]
- 7. Matsuda Y., Nakashima H., Morita M., Takasu Y., J. Electrochem. Soc. 1981, 128, 2552. [Google Scholar]
- 8. Wu J., Cao Y., Zhao H., Mao J., Guo Z., Carbon Energy 2019, 1, 57. [Google Scholar]
- 9. Zhang Q., Mao J., Pang W. K., Zheng T., Sencadas V., Chen Y., Liu Y., Guo Z., Adv. Energy Mater. 2018, 8, 1703288. [Google Scholar]
- 10.a) Yaroshevsky A. A. J. G. I., Geochem. Int. 2006, 44, 48; [Google Scholar]; b) Taylor S. R., McLennan S. M., The Continental Crust: Its Composition and Evolution, Blackwell Scientific Publisher, Palo Alto, CA: 1985. [Google Scholar]
- 11.a) Exchange L. M., https://www.lme.com/, (accessed: August 2024).; b) Gao Y., Yu Q., Yang H., Zhang J., Wang W., Adv. Mater. 2024, 36, 2405989; [DOI] [PubMed] [Google Scholar]; c) Shanghai Metals Market , https://www.metal.com/ (accessed: August 2024).
- 12.a) Kania H., Saternus M., Appl. Sci. 2003, 13, 2023. [Google Scholar]; b) Grew E. S., Elements 2020, 16, 235; [Google Scholar]; c) Manning D. A., Agronomy Sustainable Dev. 2010, 30, 281; [Google Scholar]; d) Mudd G. M., Jowitt S. M., Werner T., Ore Geol. Rev. 2017, 80, 1160. [Google Scholar]
- 13. Nathan M. G. T., Yu H., Kim G. T., Kim J. H., Cho J. S., Kim J., Kim J. K., Adv. Sci. 2022, 9, 2105882. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 14. Sada K., Darga J., Manthiram A., Adv. Energy Mater. 2023, 13, 2302321. [Google Scholar]
- 15. Xu Y. S., Guo S. J., Tao X. S., Sun Y. G., Ma J., Liu C., Cao A. M., Adv. Mater. 2021, 33, 2100409. [DOI] [PubMed] [Google Scholar]
- 16. Liu S., Kang L., Jun S. C., Adv. Mater. 2021, 33, 2004689. [DOI] [PubMed] [Google Scholar]
- 17. Eftekhari A., J. Power Sources 2004, 126, 221. [Google Scholar]
- 18. Chong S., Chen Y., Zheng Y., Tan Q., Shu C., Liu Y., Guo Z., J. Mater. Chem. A 2017, 5, 22465. [Google Scholar]
- 19.a) Zhang C., Xu Y., Zhou M., Liang L., Dong H., Wu M., Yang Y., Lei Y., Adv. Funct. Mater. 2017, 27, 1604307; [Google Scholar]; b) Chong S., Wu Y., Guo S., Liu Y., Cao G., Energy Storage Mater. 2019, 22, 120. [Google Scholar]
- 20. Xue L., Li Y., Gao H., Zhou W., Lü X., Kaveevivitchai W., Manthiram A., Goodenough J. B., J. Am. Chem. Soc. 2017, 139, 2164. [DOI] [PubMed] [Google Scholar]
- 21. Liu C. l., Luo S. h., Huang H. b., Zhai Y. c., Wang Z. w., Chem. Eng. J. 2019, 356, 53. [DOI] [PubMed] [Google Scholar]
- 22. Chen Y., Luo W., Carter M., Zhou L., Dai J., Fu K., Lacey S., Li T., Wan J., Han X., Bao Y., Hu L., Nano Energy 2015, 18, 205. [Google Scholar]
- 23. Lin X., Huang J., Tan H., Huang J., Zhang B., Energy Storage Mater. 2019, 16, 97. [Google Scholar]
- 24. Vaalma C., Giffin G. A., Buchholz D., Passerini S., J. Electrochem. Soc. 2016, 163, A1295. [Google Scholar]
- 25. Kim H., Seo D., Kim J. C., Bo S., Liu L., Shi T., Ceder G., Adv. Mater. 2017, 29, 1702480. [DOI] [PubMed] [Google Scholar]
- 26. Hironaka Y., Kubota K., Komaba S., Chem. Commun. 2017, 53, 3693. [DOI] [PubMed] [Google Scholar]
- 27. Kim H., Kim J. C., Bo S.‐H., Shi T., Kwon D.‐H., Ceder G., Adv. Energy Mater. 2017, 7, 1700098. [Google Scholar]
- 28. Nathan M. G. T., Yu H., Kim G.‐T., Kim J.‐H., Cho J. S., Kim J., Kim J.‐K., Adv. Sci. 2022, 9, 2105882. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 29. Kim H., Seo D., Urban A., Lee J., Kwon D., Bo S.‐H., Shi T., Papp J. K., McCloskey B. D., Ceder G., Chem. Mater. 2018, 30, 6532. [Google Scholar]
- 30. Naveen N., Han S. C., Singh S. P., Ahn D., Sohn K., Pyo M., J. Power Sources 2019, 430, 137. [Google Scholar]
- 31. Hwang J., Kim J., Yu T., Myung S., Sun Y., Energy Environ. Sci. 2018, 11, 2821. [Google Scholar]
- 32. Zhang Y., Niu X., Tan L., Deng L., Jin S., Zeng L., Xu H., Zhu Y., ACS Appl. Mater. Interfaces 2020, 12, 9332. [DOI] [PubMed] [Google Scholar]
- 33. Yang Y., Liu Z., Deng L., Tan L., Niu X., Sanad M. M. S., Zeng L., Zhu Z., Zhu Y., Chem. Commun. 2019, 55, 14988. [DOI] [PubMed] [Google Scholar]
- 34. Oh G., Kansara S., Xu X., Liu Y., Xiong S., Hwang J., Adv. Funct. Mater. 2024, 34, 2401210. [Google Scholar]
- 35. Meng Y., Nie C., Guo W., Liu D., Chen Y., Ju Z., Zhuang Q., Mater. Today Energy 2022, 25, 100982. [Google Scholar]
- 36. Mathew V., Kim S., Kang J., Gim J., Song J., Baboo J. P., Park W., Ahn D., Han J., Gu L., Wang Y., Hu Y., Sun Y., Kim J., NPG Asia Mater 2014, 6, 138. [Google Scholar]
- 37. Chihara K., Katogi A., Kubota K., Komaba S., Chem. Commun. 2017, 53, 5208. [DOI] [PubMed] [Google Scholar]
- 38. Liao J., Hu Q., Che B., Ding X., Chen F., Chen C., J. Mater. Chem. A 2019, 7, 15244. [Google Scholar]
- 39. Li J., Zheng Y., Hui K. S., Wang K., Zha C., Dinh D. A., Tu J., Shao Z., Hui K. N., Energy Storage Mater. 2023, 61, 102852. [Google Scholar]
- 40. Park W. B., Han S. C., Park C., Hong S. U., Han U., Singh S. P., Jung Y. H., Ahn D., Sohn K.‐S., Pyo M., Adv. Energy Mater. 2018, 8, 1703099. [Google Scholar]
- 41. Ko W., Park H., Jo J. H., Lee Y., Kang J., Jung Y. H., Jeon T., Myung S., Kim J., Nano Energy 2019, 66, 104184. [Google Scholar]
- 42. Tang M., Wu Y., Chen Y., Jiang C., Zhu S., Zhuo S., Wang C., J. Mater. Chem. A 2019, 7, 486. [Google Scholar]
- 43. Zhang C., Xu Y., He K., Dong Y., Zhao H., Medenbach L., Wu Y., Balducci A., Hannappel T., Lei Y., Small 2020, 16, 2002953. [DOI] [PubMed] [Google Scholar]
- 44. Li H., Joule 2019, 3, 911. [Google Scholar]
- 45. An S. J., Li J., Daniel C., Mohanty D., Nagpure S., Wood D. L. III, Carbon 2016, 105, 52. [Google Scholar]
- 46.a) Liu Q., Xu R. G., Mu D. B., Tan G. Q., Gao H. C., Li N., Chen R. J., Wu F., Carbon Energy 2022, 4, 458; [Google Scholar]; b) Nobuhara K., Nakayama H., Nose M., Nakanishi S., Iba H., J. Power Sources 2013, 243, 585. [Google Scholar]
- 47. Fan L., Ma R., Zhang Q., Jia X., Lu B., Angew. Chem., Int. Ed. 2019, 131, 10610. [DOI] [PubMed] [Google Scholar]
- 48. Jian Z., Luo W., Ji X., J. Am. Chem. Soc. 2015, 137, 11566. [DOI] [PubMed] [Google Scholar]
- 49. Mao Z., Shi X., Zhang T., Zheng Z., Liang X., Wang R., Jin J., He B., Gong Y., Wang H., Small 2023, 19, 2302987. [DOI] [PubMed] [Google Scholar]
- 50. Irisarri E., Ponrouch A., Palacin M., J. Electrochem. Soc. 2015, 162, A2476. [Google Scholar]
- 51.a) Lei H., Li J., Zhang X., Ma L., Ji Z., Wang Z., Pan L., Tan S., Mai W., Infomat 2022, 4, 12272; [Google Scholar]; b) Wu Z., Zou J., Shabanian S., Golovin K., Liu J., Chem. Eng. J. 2022, 427, 130972. [Google Scholar]
- 52. Guo Z., Xu Z., Xie F., Jiang J., Zheng K., Alabidun S., Crespo‐Ribadeneyra M., Hu Y. S., Au H., Titirici M. M., Adv. Mater. 2023, 35, 2304091. [DOI] [PubMed] [Google Scholar]
- 53. Xu W., Li H., Zhang X., Chen T. Y., Yang H., Min H., Shen X., Chen H. Y., Wang J., Adv. Funct. Mater. 2024, 34, 2309509. [Google Scholar]
- 54.a) Loaiza L. C., Monconduit L., Seznec V., Small 2020, 16, 1905260; [DOI] [PubMed] [Google Scholar]; b) Lee S., Jung S. C., Han Y. K., J. Power Sources 2019, 415, 119. [Google Scholar]
- 55. Wagner M. R., Raimann P. R., Trifonova A., Möller K. C., Besenhard J. O., Winter M., Anal. Bioanal. Chem. 2004, 379, 272. [DOI] [PubMed] [Google Scholar]
- 56. Huang H., Wang J., Yang X., Hu R., Liu J., Zhang L., Zhu M., Angew. Chem., Int. Ed. 2020, 132, 14612. [DOI] [PubMed] [Google Scholar]
- 57. Li L., Huang A., Jiang H., Li Y., Pan X., Chen T. Y., Chen H. Y., Peng S., Angew. Chem., Int. Ed. 2024, 136, 202412077. [DOI] [PubMed] [Google Scholar]
- 58. Liu Z., Liu X., Wang B., Wang X., Lu D., Shen D., Sun Z., Liu Y., Zhang W., Zhang Q., eScience 2023, 3, 100177. [Google Scholar]
- 59. Wang B., Shi L., Zhou Y., Wang X., Liu X., Shen D., Yang Q., Xiao S., Zhang J., Li Y., Small 2024, 20, 2310736. [DOI] [PubMed] [Google Scholar]
- 60. Verdianto A., Lim H., Park J., Kim S. O., J. Alloys Comp. 2023, 942, 168950. [Google Scholar]
- 61. Wang Y., Niu P., Li J., Wang S., Li L., Energy Storage Mater. 2021, 34, 436. [Google Scholar]
- 62. Wang D., Zhang L., Fu Y., Sun Z., Wang T., Shi Y., Yang G., Ma R., Liu Z., Wu L., Adv. Funct. Mater. 2024, 34, 2409090. [Google Scholar]
- 63. Zhou E., Luo X., Jin H., Wang C., Lu Z., Xie Y., Zhou S., Chen Y., He Z., Ma R., J. Am. Chem. Soc. 2024, 146, 4752. [DOI] [PubMed] [Google Scholar]
- 64. Peng Q., Sun Y., Wang L., Dong H., Wang H., Xiao Y., Chou S., Xu Y., Wang Y., Chen S., Small 2024, 20, 2308953. [DOI] [PubMed] [Google Scholar]
- 65. Chen R. H., Xiao J. M., Zhu N. N., Xiao R. H., Liu W. Y., Zeng X., Chen Y. F., Yi Z. J., Zhu G. Y., Liu L., Angew. Chem., Int. Ed. 2024, 136, 202402497. [Google Scholar]
- 66. Yao Z., Liu Y., Thanwisai P., Hou J., Meng Z., Mei L., Zhu X., Liu S., Wang Y., ACS Sustainable Chem. Eng. 2024, 12, 14472. [Google Scholar]
- 67. Zou J., Fu C., Zhang Y., Fan K., Chen Y., Zhang C., Zhang G., Dai H., Cao Y., Ma J., Adv. Funct. Mater. 2023, 33, 2303678. [Google Scholar]
- 68. Ma M., Chong S., Yao K., Liu H. K., Dou S. X., Huang W., Matter 2023, 6, 3220. [Google Scholar]
- 69. Zhang C., Zhao H., Lei Y., Energy Environ. Mater. 2020, 3, 105. [Google Scholar]
- 70. Peng Y., Wei M., Zhang D., Liu X., Xiong X., Gao W., Fan W., Yang H., Zhou Q., Wang T., Nano Energy 2024, 130, 110077. [Google Scholar]
- 71. Kaur H., Konkena B., McCrystall M., Synnatschke K., Gabbett C., Munuera J., Smith R., Jiang Y., Bekarevich R., Jones L., ACS Nano 2024, 18, 20213. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 72. Yang X., Gao Y., Fan L., Rao A. M., Zhou J., Lu B., Adv. Energy Mater. 2023, 13, 2302589. [Google Scholar]
- 73. Yan B., Sun H., Liu X., Fu X., Xu C., Zhang T., Tao H., Zhang L., Li X., Yang X., Energy Environ. Sci. 2024, 17, 3419. [Google Scholar]
- 74. Zhang W., Mao J., Li S., Chen Z., Guo Z., J. Am. Chem. Soc. 2017, 139, 3316. [DOI] [PubMed] [Google Scholar]
- 75. Zhang W., Pang W. K., Sencadas V., Guo Z., Joule 2018, 2, 1534. [Google Scholar]
- 76. Qin M., Ren W., Meng J., Wang X., Yao X., Ke Y., Li Q., Mai L., ACS Sustainable Chem. Eng. 2019, 7, 11564. [Google Scholar]
- 77. Shu W., Huang M., Geng L., Qiao F., Wang X., Small 2023, 19, 2207080. [DOI] [PubMed] [Google Scholar]
- 78. Yuan Y., Xu J., Li X., Li X., Wang X., Li X., Dai S., J. Alloys Comp. 2022, 923, 166457. [Google Scholar]
- 79. Ma H., Jiang M., Hou Z., Li T., Zhang X., Gao Y., Peng J., Li Y., Wang J.‐G., Energy Storage Mater. 2024, 70, 103411. [Google Scholar]
- 80. Ge J., Fan L., Rao A. M., Zhou J., Lu B., Nat. Sustain. 2022, 5, 225. [Google Scholar]
- 81. Li A., Duan L., Liao J., Sun J., Man Y., Zhou X., ACS Appl. Energy Mater. 2022, 5, 11789. [Google Scholar]
- 82. Manumpil M. A., Leal‐Cervantes C., Hudson M. R., Brown C. M., Karunadasa H. I., Inorganic Chem. 2017, 56, 12682. [DOI] [PubMed] [Google Scholar]
- 83.a) Husmann S., Zarbin A. J. G., Dryfe R. A. W., Electrochim. Acta 2020, 349, 136243; [Google Scholar]; b) Zhao X., Liu N., Zheng M., Wang X., Xu Y., Liu J., Li F., Wang L., ACS Energy Lett. 2024, 9, 2748. [Google Scholar]
- 84. Zhou M., Tian X., Sun Y., He X., Li H., Ma T., Zhao Q., Qiu J., Nano Res. 2023, 16, 6326. [Google Scholar]
- 85. Chong S., Yang J., Sun L., Guo S., Liu Y., Liu H. K., ACS Nano 2020, 14, 9807. [DOI] [PubMed] [Google Scholar]
- 86. Wang Y., Zhang F., Long Q., Li S., Guo D., Zhu Z., Zhang H., Energy Storage Mater. 2024, 71, 103399. [Google Scholar]
- 87. Xiao Z., Meng J., Xia F., Wu J., Liu F., Zhang X., Xu L., Lin X., Mai L., Energy Environ. Sci. 2020, 13, 3129. [Google Scholar]
- 88. Duan L., Shao C., Liao J., Song L., Zhang Y., Li R., Guo S., Zhou X., Zhou H., Angew. Chem., Int. Ed. 2024, 63, 202400868. [DOI] [PubMed] [Google Scholar]
- 89. Han W., Gao X., Song Y., Wang X., Gao G., Chen H., Gu Q., Luo W., Small 2024, 20, 2400252. [DOI] [PubMed] [Google Scholar]
- 90. Wang S.‐S., Liu Z., Gao X., Wang X., Chen H., Luo W.‐B., ACS Appl. Mater. Interface 2023, 15, 57165. [DOI] [PubMed] [Google Scholar]
- 91. Zhang Z., Hu Q., Liao J., Xu Y., Duan L., Tian R., Du Y., Shen J., Zhou X., Nano Lett. 2023, 23, 694. [DOI] [PubMed] [Google Scholar]
- 92. Lv J., Wang B., Hao J., Ding H., Fan L., Tao R., Yang H., Zhou J., Lu B., eScience 2023, 3, 100081. [Google Scholar]
- 93. Zhao S., Yan K., Munroe P., Sun B., Wang G., Adv. Energy Mater. 2019, 9, 1803757. [Google Scholar]
- 94. Xiao Z., Xia F., Xu L., Wang X., Meng J., Wang H., Zhang X., Geng L., Wu J., Mai L., Adv. Funct. Mater. 2022, 32, 2108244. [Google Scholar]
- 95. Wang H., Meng J., Xiao Z., Liu W., Liu F., Li Y., Zhou L., Wu J., Energy Storage Mater. 2024, 67, 103324. [Google Scholar]
- 96. Wang C. S., Hong J., Electrochem. Solid. St. 2007, 10, A65. [Google Scholar]
- 97. Huang Y., Zhang X., Chen N., Tian R., Zeng Y., Du F., Small 2023, 19, 2302841. [DOI] [PubMed] [Google Scholar]
- 98. Zhao J., Qin Y., Li L., Wu H., Jia X., Zhu X., Zhao H., Su Y., Ding S., Sci. Bull. 2023, 68, 593. [DOI] [PubMed] [Google Scholar]
- 99. Liao J., Zhang X., Zhang Q., Hu Q., Li Y., Du Y., Xu J., Gu L., Zhou X., Nano Lett. 2022, 22, 4933. [DOI] [PubMed] [Google Scholar]
- 100. Tan S., Shadike Z., Li J., Wang X., Yang Y., Lin R., Cresce A., Hu J., Hunt A., Waluyo I., Nat. Energy 2022, 7, 484. [Google Scholar]
- 101. Zhang L., Liu W., Chen S., Cui L., Wu Q., Lin K., Liu Y., Wang H., Lu S., Xiang Y., Electrochim. Acta 2023, 451, 142214. [Google Scholar]
- 102. An Y., Fei H., Zeng G., Ci L., Xi B., Xiong S., Feng J., J. Power Sources 2018, 378, 66. [Google Scholar]
- 103. Ma Z., Gao Y., Bao C., Xia X., Liu H., Electrochim. Acta 2023, 440, 141703. [Google Scholar]
- 104. Chang X., Sun N., Zhou H., Soomro R. A., Xu B., Chinese Chem. Lett. 2023, 34, 107312. [Google Scholar]
- 105. Zhang Y., Yin B., Ma M., Cheng B., Zhu L., Xu H., Wu Q., Tang S., He H., Mater. Today Energy 2023, 34, 101315. [Google Scholar]
- 106. Yang K., Zhou W., Fu Q., Xiao L., Mo Y., Ke J., Shen W., Wang Z., Tu J., Chen S., Adv. Funct. Mater. 2023, 33, 2306190. [Google Scholar]
- 107. Wang X., Luo Z., Huang J., Chen Z., Xiang T., Feng Z., Wang J., Wang S., Ma Y., Yang H., J. Mater. Sci. Technol. 2023, 147, 47. [Google Scholar]
- 108. Wang L., Yang J., Li J., Chen T., Chen S., Wu Z., Qiu J., Wang B., Gao P., Niu X., J. Power Sources 2019, 409, 24. [Google Scholar]
- 109. Chen W., Zhang D., Fu H., Li J., Yu X., Zhou J., Lu B., ACS Nano 2024, 18, 12512. [DOI] [PubMed] [Google Scholar]
- 110. Ma X., Fu H., Shen J., Zhang D., Zhou J., Tong C., Rao A. M., Zhou J., Fan L., Lu B., Angew. Chem., Int. Ed. 2023, 62, 202312973. [DOI] [PubMed] [Google Scholar]
- 111. Hu Y., Fu H., Geng Y., Yang X., Fan L., Zhou J., Lu B., Angew. Chem., Int. Ed. 2024, 136, 202403269. [DOI] [PubMed] [Google Scholar]
- 112. Yi X., Fu H., Rao A. M., Zhang Y., Zhou J., Wang C., Lu B., Nat. Sustain. 2024, 7, 326. [Google Scholar]
- 113. Yuan F., Hu J., Lei Y., Zhao R., Gao C., Wang H., Li B., Kang F., Zhai D., ACS Nano 2022, 16, 12511. [DOI] [PubMed] [Google Scholar]
- 114. Wang Z., Luo K., Wu J.‐F., Gao P., Wang K., Chen S., Tu J., Fan X., Liu J., Energy Environ. Sci. 2024, 17, 274. [Google Scholar]
- 115. Zhou W., Mo Y., Gao P., Wang K., Ke J., Liu Z., Chen S., Liu J., Adv. Funct. Mater. 2024, 34, 2312994. [Google Scholar]
- 116. Hosaka T., Kubota K., Kojima H., Komaba S., Chem. Commun. 2018, 54, 8387. [DOI] [PubMed] [Google Scholar]
- 117.a) Liu S., Mao J., Zhang Q., Wang Z., Pang W. K., Zhang L., Du A., Sencadas V., Zhang W., Guo Z., Angew. Chem., Int. Ed. 2020, 59, 3638; [DOI] [PubMed] [Google Scholar]; b) Liu S., Mao J., Zhang L., Pang W., Du A., Guo Z., Adv. Mater. 2021, 33, 2006313. [DOI] [PubMed] [Google Scholar]
- 118. Zhang D., Fu H., Ma X., Yu X., Li F., Zhou J., Lu B., Angew. Chem., Int. Ed. 2024, 136, 202405153. [DOI] [PubMed] [Google Scholar]
- 119. Gao Y., Li W., Ou B., Zhang S., Wang H., Hu J., Kang F., Zhai D., Adv. Funct. Mater. 2023, 33, 2305829. [Google Scholar]
- 120. Kang S., Jeon B., Hong S., Lee H., Chem. Eng. J. 2022, 443, 136403. [Google Scholar]
- 121. Tsai W., J. Hazardous Mater. 2005, 119, 69. [DOI] [PubMed] [Google Scholar]
- 122. Xiang X., Liu D., Song J., Zhu X., Xie Z., Tang H., Zheng H., Qu D., J. Alloys Comp. 2023, 960, 170864. [Google Scholar]
- 123. Liang L., Tang M., Zhu Q., Wei W., Wang S., Wang J., Chen J., Yu D., Wang H., Adv. Energy Mater. 2023, 13, 2300453. [Google Scholar]
- 124. Zhao S., Liu Z., Xie G., Guo Z., Wang S., Zhou J., Xie X., Sun B., Guo S., Wang G., Energy Environ. Sci. 2022, 15, 3015. [Google Scholar]
- 125. Luo G., Feng X., Qian M., Zhang W., Qin W., Wu C., Pan L., Mater. Chem. Frontiers 2023, 7, 3011. [Google Scholar]
- 126.a) Vaalma C., Buchholz D., Weil M., Passerini S., Nat. Rev. Mater. 2018, 3, 1; [Google Scholar]; b) Baumann M., Häringer M., Schmidt M., Schneider L., Peters J. F., Bauer W., Binder J. R., Weil M., Adv. Energy Mater. 2022, 12, 2202636. [Google Scholar]
- 127. Ahmed S., Nelson P. A., Gallagher K. G., Susarla N., Dees D. W., J. Power Sources 2017, 342, 733. [Google Scholar]
- 128. Yan Z., Obrovac M., J. Power Sources 2020, 464, 228228. [Google Scholar]
- 129. Innocenti A., Beringer S., Passerini S., Nat. Rev. Mater. 2024, 9, 347. [Google Scholar]
- 130. Northern graphite , https://www.northerngraphite.com (accessed: August 2024).
- 131.Sigma, https://www.sigmaaldrich.com/ (accessed: December 2024).
- 132. Innocenti A., Bresser D., Garche J., Passerini S., Nat. Commun. 2024, 15, 4068. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 133. Mo Y., Zhou W., Wang K., Xiao K., Chen Y., Wang Z., Tang P., Xiao P., Gong Y., Chen S., ACS Energy Lett. 2023, 8, 995. [Google Scholar]
- 134. Fan L., Xie H., Hu Y., Caixiang Z., Rao A. M., Zhou J., Lu B., Energy Environ. Sci. 2023, 16, 305. [Google Scholar]
- 135. Ji B., Yao W., Zheng Y., Kidkhunthod P., Zhou X., Tunmee S., Sattayaporn S., Cheng H.‐M., He H., Tang Y., Nat. Commun. 2020, 11, 1225. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 136. Li L., Hu Z., Lu Y., Wang C., Zhang Q., Zhao S., Peng J., Zhang K., Chou S. L., Chen J., Angew. Chem., Int. Ed. 2021, 133, 13160. [DOI] [PubMed] [Google Scholar]
- 137. Deng L., Qu J., Niu X., Liu J., Zhang J., Hong Y., Feng M., Wang J., Hu M., Zeng L., Nat. Commun. 2021, 12, 2167. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 138. Wen J., Fu H., Zhang D., Ma X., Wu L., Fan L., Yu X., Zhou J., Lu B., ACS Nano 2023, 17, 16135. [DOI] [PubMed] [Google Scholar]
- 139. Liao J., Chen C., Hu Q., Du Y., He Y., Xu Y., Zhang Z., Zhou X., Angew. Chem., Int. Ed. 2021, 133, 25779. [DOI] [PubMed] [Google Scholar]
- 140. Cheng L., Lan H., Gao Y., Dong S., Wang Y., Tang M., Sun X., Huang W., Wang H., Angew. Chem., Int. Ed. 2024, 63, 202315624. [DOI] [PubMed] [Google Scholar]
- 141. Li A., Man Y., Liao J., Duan L., Ji X., Zhou X., Nano Lett. 2023, 23, 10066. [DOI] [PubMed] [Google Scholar]
- 142. Li F., Gu X., Cui A., Li Y., Dong S., Wu S., Cheng Z., Yao Q., Yang J., Wu M., Adv. Funct. Mater. 2024, 34, 2313146. [Google Scholar]
- 143. Commercial PIBs from Group 1 , https://group1.ai/ (accessed: December 2024).
- 144. Liu J., Duan Q., Qi K., Liu Y., Sun J., Wang Z., Wang Q., J. Energy Storage 2022, 46, 103910. [Google Scholar]
- 145. Hu Y., Li Y., ACS Energy Lett. 2021, 6, 4115. [Google Scholar]
