Abstract
Objective
The use of polishing pastes in the final surface preparation of resin composite restorations has become increasingly common. This study aimed to evaluate the effects of polishing pastes containing abrasives of different particle sizes on the surface roughness, microhardness, gloss, and color change of resin composites.
Materials and methods
Specimens (10 × 2 mm³) were prepared from nanofill, nanohybrid, and supra-nano resin composites. After finishing and polishing procedures, polishing pastes containing diamond particles of < 1 μm (Lucida, Diashine), 1 μm (DiaPolisher, GC), and 0.5 μm (Diamond Polish Mint, Ultradent) were applied. Baseline measurements of surface roughness, microhardness, gloss, and color were recorded. Following artificial aging (5000 cycles), changes in these parameters were evaluated. Data were analyzed using two-way analysis of variance (ANOVA) and Tukey’s post hoc test (p < 0.05).
Results
After the finishing and polishing procedures, no statistically significant decrease in surface roughness was observed in the nanofill and supra-nano resin composites following paste application (p > 0.05), whereas a statistically significant reduction was found in the nanohybrid composite (p < 0.001). No statistically significant difference was detected among the polishing pastes containing abrasives of different particle sizes (p > 0.05). Following the finishing and polishing procedures, specimens treated with polishing pastes exhibited a statistically significant reduction in surface roughness (p < 0.001), whereas no significant differences were observed among the pastes containing abrasives of different particle sizes (p > 0.05). The application of polishing pastes did not affect the surface microhardness of the resin composites. After the finishing and polishing procedures, the use of polishing pastes did not influence the gloss of nanofill and supra-nano resin composites (p > 0.05), but resulted in a statistically significant increase in the gloss of nanohybrid composites (p < 0.001). Resin composites treated with polishing pastes after finishing and polishing exhibited significantly less color change (p < 0.001).
Conclusions
While polishing pastes did not influence the microhardness of resin composites, they improved surface roughness, gloss, and color stability. No significant differences were found among the different polishing pastes.
Clinical relevance
The use of polishing pastes following finishing and polishing procedures may positively influence the surface roughness, gloss, and color stability of resin composites, thereby enhancing the clinical success of restorations.
Keywords: Color change, Finishing and polishing, Gloss, Resin composite, Surface roughness
Introduction
In recent years, the application of nanotechnology has enabled the development of resin composites with different filler particle sizes, which not only exhibit improved mechanical and physical stability in the oral environment but also provide esthetic properties compatible with tooth color. Reducing filler particle size and increasing filler loading enhance the wear resistance and surface properties of resin composites [1]. Nanofill composites contain nanofillers and nanoclusters [2], while nanohybrid composites incorporate both nano- and hybrid-sized fillers [3]. The homogeneous dispersion of nanoparticles within the resin matrix contributes positively to hardness, wear resistance, and esthetics [4]. Supra-nano resin composites, with their spherical fillers, are reported to maintain high surface gloss and provide natural opalescence by scattering and refracting incident light [5].
The esthetic performance of composite restorations is improved through finishing and polishing procedures. Finishing refers to shaping the restoration to achieve the desired anatomy and proper occlusion, whereas polishing produces a smooth and highly glossy surface [6]. Finishing and polishing systems differ substantially in terms of abrasive composition, type, and particle hardness [6]. Simplified polishing systems have been reported to reduce chairside time and provide comparable surface roughness to multi-step systems [7]. However, other studies have indicated that simplified systems may not achieve the same improvement in surface smoothness as multi-step protocols [8].
Finishing and polishing systems contain abrasives such as silicon oxide, aluminum oxide, and diamond particles embedded in discs or rubber carriers [9]. To achieve ideal surface characteristics in resin composites, abrasive discs should be used sequentially, progressing from coarse to fine grit sizes [10].
Rough surfaces on resin composites make them more susceptible to discoloration, reduce gloss, and impair light reflection [11]. Moreover, rough surfaces facilitate plaque accumulation, gingival inflammation, secondary caries, and decreased wear resistance [12]. Surface roughness values greater than 0.2 μm significantly increase biofilm formation, whereas values below this threshold are considered optimal for intraoral restorations [13]. Furthermore, the surface roughness of resin composite restorations is closely related to their structural properties, susceptibility to water sorption, and the adequacy of finishing and polishing procedures [14, 15].
The influence of polishing on the color stability of resin composites is linked to the surface topography created after polishing. Rougher surfaces are more prone to extrinsic discoloration [12]. The perceptibility threshold (PT) represents the minimum color difference detectable by the human eye, while the acceptability threshold (AT) refers to the color difference considered clinically acceptable. Based on CIE L* a* b* values, the 50:50 PT has been reported as ΔE00: 0.8 and the 50:50 AT as ΔE00: 1.8 [16].
Gloss is an optical property related to specular reflection from a surface [17, 18]. In resin composites, gloss is influenced by the refractive indices of the organic and inorganic matrix, filler particle size, and the degree of filler–matrix similarity [19, 20]. Lower filler–matrix homogeneity results in reduced light reflection [20].
Restorative materials used in dentistry are exposed to factors such as pH fluctuations, occlusal forces, and thermal changes in the oral cavity. Their resistance to these challenges is generally associated with higher surface hardness values, which contribute to mechanical strength, scratch and wear resistance, and the ability to preserve form under functional stress [21].
The final stage of polishing resin composite restorations typically involves the application of polishing pastes following sequential use of abrasive discs, resulting in a smooth and glossy surface [6]. The outcome of this step depends on the composition of the paste, duration of application, applied pressure, and whether the procedure is performed dry or wet [6]. Polishing pastes are usually applied with flexible rubber cups, although some studies have suggested that felt polishing brushes and other special abrasives may significantly enhance their effectiveness [6, 22].
Finishing and polishing are clinically important procedures following the placement of any direct restoration, as they reduce the risk of fracture, plaque accumulation, and surface degradation, help prevent surface defects, and create a light-reflecting surface that improves color harmony. Although several studies have examined the effects of finishing and polishing systems on resin composites [7, 8], research specifically evaluating the impact of polishing pastes with different abrasive particle sizes on the optical and surface properties of resin composites remains limited. The aim of this study was to evaluate the effects of diamond particle–containing polishing pastes with different particle sizes, applied after a two-step diamond-impregnated spiral system, on the surface roughness, microhardness, gloss, and color change of nanofill, nanohybrid, and supra-nano resin composites. The first null hypothesis of this study was that polishing pastes containing abrasives of different particle sizes would not affect the surface roughness of resin composites. The second null hypothesis was that polishing pastes containing abrasives of different particle sizes would not influence the microhardness values of resin composites. The third null hypothesis stated that polishing pastes containing abrasives of different particle sizes would not alter the gloss values of resin composites. The fourth null hypothesis was that polishing pastes containing abrasives of different particle sizes would not affect the color change of resin composites.
Materials and methods
Nanofill (3M Filtek Universal Restorative, 3M ESPE, USA), nanohybrid (G-aenial A’chord, GC Japan), and supra-nano (Estelite Asteria, Tokuyama, Japan) resin composites were used in the study. The sample size was calculated using the G*Power software (Heinrich-Heine-Universität Düsseldorf, Germany) with a large effect size (0.40), α = 0.05 error level, and 80% power (1 − β = 0.80) [23].
A total of 96 resin composite specimens (n = 8 per group) were prepared and divided into four subgroups, including three polishing paste groups and one control group. Information about the resin composites used in the study is shown in Table 1.
Table 1.
Composition of materials used in the study
| Resin composite | Type | Resin composition | Filler type/size | Load vol % | Lot number |
|---|---|---|---|---|---|
|
3M Filtek Universal Restorative (3 M ESPE, USA) |
Nanofill | AUDMA, AFM, Diurethane-DMA, 1,12 Dodecane-DMA | Silica, Ytterbium trifluoride, Zirconia/silica cluster (0.004–0.1 μm) |
76.5 wt% 58.4 vol% |
11317767 |
|
Estelite Asteria (Tokuyama, Japan) |
Supra-nano | Bis-GMA, Bis-MEPP, UDMA, TEGDMA | Spherical supra-nano fillers (~ 0.25 μm) |
82 wt% 71 vol% |
W1691 |
|
G-aenial A’chord (GC Corp., Japan) |
Nano-hybrid | UDMA, Bis-MEPP, Bis-EMA, Bis-GMA, TEGDMA | Pre-polymerised fillers, barium glass, fumed silica (0.01–10 μm) |
78.4 wt% 65 vol% |
2401191 |
Preparation of specimens
Coposite specimens were prepared using a silicone mold with a diameter of 10 mm and a thickness of 2 mm. The resin composites were placed into a 3D-printed silicone mold (RTV-2, Shore A 10) using a hand instrument. Then, a glass slide (1 mm thick) was placed on top, and polymerization was performed for 20 s at 1000 mW/cm² using an LED light-curing unit (DTE O-Light Plus, Germany) with the tip in contact with the glass slide. Before the polymerization of each specimen group, the irradiance (mW/cm²) of the LED light-curing unit was measured using a radiometer (LED Radiometer; SDI Limited, Australia).
At the initial stage, all resin composite groups were finished using a two-step diamond-impregnated spiral system (Clearfil Twist Dia; Kuraray, Japan). The finishing procedure was performed with a handpiece connected to a dental unit (GOLDSPEED Evo S1-L; Stern Weber, Italy) under continuous movement and water cooling at 10,000 rpm, with each spiral applied for 30 s by a single operator.
After the finishing procedures of the resin composites were completed, the specimens were divided into four subgroups (n = 8): three polishing paste groups and one control group (without paste application). Polishing of the resin composite groups was performed using a felt disc (Lucida Click; Diashine, Italy) with three diamond-containing polishing pastes: Lucida (sub-micron particle size < 1 μm; Diashine, Italy), DiaPolisher (1 μm diamond particles; GC Corp., Japan), and Diamond Polish Mint (0.5 μm diamond particles; Ultradent, USA). The application of polishing pastes was carried out with a handpiece connected to a dental unit (GOLDSPEED Evo S1-L; Stern Weber, Italy) under continuous movement at 5000 rpm for 1 min (0.1 mL paste per specimen) by a single operator. After the polishing procedure, the specimens were stored in distilled water at 37 °C for 24 h in an incubator (FN 500; Nüve, Turkey). Subsequently, initial surface roughness, microhardness, gloss, and color measurements of the polishing paste and control groups were performed.
Measurement of surface roughness, microhardness, gloss, and color
The surface properties of the composite specimens after finishing and polishing were examined using a confocal microscope (Smartproof 5, Zeiss, Germany). Surface roughness was evaluated with the arithmetic mean roughness (Ra) parameter. Analyses were performed on images taken from an area of 0.5 × 0.5 μm using a 20×/0.7 objective lens. Image processing and evaluation were performed with surface analysis software (ConfoMap ST 9.3.10494; Zeiss, Germany).
Microhardness was measured using a Vickers hardness tester (HMV-G, Shimadzu, Japan). A load of 980.7 mN was applied for 15 s at the center of the specimen. Two measurements were made at the central points of each specimen, and the mean value was calculated.
The surface gloss of the resin composites was evaluated using a glossmeter (Novo-Curve, Rhopoint, UK). The specimens were placed on the measurement area of the device, and during measurement they were protected from external light with a black film cover. The device was calibrated before each group measurement using the calibration plate provided by the manufacturer (93.3 GU). Gloss was measured at a 2 × 2 mm area with a 60° geometry.
The baseline CIE L*(white–black), a*(red–green), b* (yellow–blue) values of the specimens, as well as the CIE L*a*b* values after the aging procedure, were measured using a spectrophotometer (CM-26dG, Konica Minolta, Japan). Color change was calculated using the CIEDE2000 (ΔE00) formula based on the L, a, and b values.
Aging
Specimens whose baseline roughness, microhardness, gloss, and color values had been measured were placed in a thermocycling device (THE1400, SD Mechatronik, Germany). Distilled water (Veolia, UK) was used in the device. The specimens underwent 5000 cycles between + 5 °C and + 55 °C, each with a dwell time of 30 s [24]. After thermocycling, surface roughness, microhardness, gloss, and color change were remeasured.
Statistical analysis
The data were analyzed using SPSS 22.0 (IBM Corp., Armonk, NY, USA). The normality of surface roughness, microhardness, gloss, and color change data was assessed with the Kolmogorov–Smirnov test. Surface roughness, microhardness, and gloss values were evaluated using two-way analysis of variance (ANOVA) and Tukey’s post hoc test (p < 0.05). Color change values were analyzed with one-way ANOVA and Tukey’s post hoc test (p < 0.05). In this study, the composite resin and polishing paste were considered independent variables, while surface roughness, microhardness, gloss, and color change were defined as dependent variables.
Results
When the effect of polishing pastes on the surface roughness (Ra, µm) of resin composites was evaluated, statistically significant differences were found (p < 0.05). In the nanofill (DiaPolisher: 0.055 ± 0.1, Lucida: 0.058 ± 0.1, Diamond Polish: 0.062 ± 0.1, and control: 0.059 ± 0.1) and supra-nano (DiaPolisher: 0.084 ± 0.1, Lucida: 0.093 ± 0.1, Diamond Polish: 0.076 ± 0.1, and control: 0.080 ± 0.1) resin composites polished with pastes, no statistically significant changes in Ra values were observed (p > 0.05). However, the Ra value of the nanohybrid composite polished with pastes (DiaPolisher: 0.059 ± 0.1, Lucida: 0.065 ± 0.1, Diamond Polish: 0.063 ± 0.1, and control: 0.091 ± 0.1) significantly decreased (p < 0.05). No statistically significant differences were found among the polishing pastes (p > 0.05). Among all resin composites, the lowest Ra value (Ra: 0.059 ± 0.1) was recorded in the nanofill composite (p < 0.05). After polishing, no significant differences in Ra values were observed between the nanofill and nanohybrid composites (p > 0.05). Following aging, no statistically significant changes in Ra values were detected in the nanofill, supra-nano, or nanohybrid resin composites polished with pastes (p > 0.05) (Table 2).
Table 2.
Initial and post-aging surface roughness values (Ra, µm) of resin composite groups treated with polishing pastes of different particle sizes
| Resin composite/polishing pastes | Control (No polishing paste) | DiaPolisher (1 μm) | Lucida (Sub-micron) | Diamond polish (0.5 μm) | ||||
|---|---|---|---|---|---|---|---|---|
| Initial | Aged | Initial | Aged | Initial | Aged | Initial | Aged | |
|
Nanofill (3M Filtek Universal Restorative) |
0.059±0.1aA | 0.064±0.1aA | 0.055±0.1aA | 0.061±0.1aA | 0.058±0.1aA | 0.062±0.1aA | 0.062±0.1aA | 0.063±0.1aA |
|
Supra-nano (Estelite Asteria) |
0.080±0.1aB | 0.093±0.1aB | 0.084±0.1aB | 0.095±0.1aB | 0.093±0.1aB | 0.099±0.1aB | 0.076±0.1aB | 0.095±0.1aB |
|
Nanohybrid (G-aenial A’chord) |
0.091±0,1aB | 0.098±0.1aB | 0.059±0.1bA | 0.069±0.1bA | 0.065±0.1bA | 0.072±0.1bA | 0.063±0.1bA | 0.069±0.1bA |
*Among the resin composites, the nanofill composite exhibited the lowest surface roughness (p < 0.001). Paste application did not result in a statistically significant difference in the surface roughness values of the nanofill and supra-nano composites (p > 0.001). In contrast, the nanohybrid composite demonstrated a significant increase in surface roughness (p < 0.001). Statistical significance was set at p < 0.05. Statistical differences in surface roughness values among the nanofill, supra-nano, and nanohybrid composites are indicated by uppercase letters (A–B), whereas statistically significant differences between the polishing methods and aging are denoted by lowercase letters (a–b)
Analysis of the effect of polishing pastes on the surface topography (Sa, µm) of resin composites revealed statistically significant differences (p < 0.001). In the nanofill (DiaPolisher: 0.159 ± 0.1, Lucida: 0.170 ± 0.1, Diamond Polish: 0.162 ± 0.1, and control: 0.163 ± 0.1) and supra-nano (DiaPolisher: 0.166 ± 0.1, Lucida: 0.171 ± 0.1, Diamond Polish: 0.166 ± 0.1, and control: 0.167 ± 0.2) resin composites polished with pastes, no statistically significant changes in Sa values were observed (p > 0.05). However, the Sa value of the nanohybrid composite polished with pastes (DiaPolisher: 0.202 ± 0.1, Lucida: 0.201 ± 0.1, Diamond Polish: 0.214 ± 0.1, and control: 0.240 ± 0.1) significantly decreased (p < 0.001). No statistically significant differences were found among the polishing pastes (p = 0.219). After aging, no significant changes in Sa values were observed in the nanofill and supra-nano resin composites polished with pastes (p > 0.05) (Table 3; Fig. 1).
Table 3.
Initial and post-aging arithmetic mean height values (Sa, µm) of resin composite groups treated with polishing pastes of different particle sizes
| Resin composite/polishing pastes | Control (No polishing paste) | DiaPolisher (1 μm) | Lucida (Sub-micron) | Diamond polish (0.5 μm) | ||||
|---|---|---|---|---|---|---|---|---|
| Initial | Aged | Initial | Aged | Initial | Aged | Initial | Aged | |
|
Nanofill (3M Filtek Universal Restorative) |
0.163±0.1aA | 0.196±0.1bA | 0.159±0.1aA | 0.179±0.1aA | 0.170±0.1aA | 0.184±0.1aA | 0.162±0.1aA | 0.173±0.1aA |
|
Supra-nano (Estelite Asteria) |
0.167±0.2aA | 0.203±0.1bA | 0.166±0.1aA | 0.168±0.1aA | 0.171±0.1aA | 0.189±0.1aA | 0.166±0.1aA | 0.183±0.1aA |
|
Nanohybrid (G-aenial A’chord) |
0.240±0,1aB | 0.248±0.1aB | 0.202±0.1bB | 0.224±0.1bB | 0.201±0.1bB | 0.222±0.1bB | 0.214±0.1bB | 0.225±0.1bB |
*Among the resin composites, the nanofill composite exhibited the lowest surface roughness (p < 0.001). Paste application did not result in a statistically significant difference in the surface roughness values of the nanofill and supra-nano composites (p > 0.001). In contrast, the nanohybrid composite demonstrated a significant increase in surface roughness (p < 0.001). Statistical significance was set at p < 0.05. Statistically significant differences in Sa values among the nanofill, supra-nano, and nanohybrid composites are shown by uppercase letters (A–B), while differences between the polishing methods and aging are shown by lowercase letters (a–b)
Fig. 1.

3D surface profile analysis of resin composite groups treated with polishing pastes of different particle sizes. a Nanofill (3M Filtek Universal Restorative), b Supra-nano (Estelite Asteria), c Nanohybrid (G-aenial A’chord)
Analysis of the effect of polishing pastes with different particle sizes on the surface microhardness (VHN) of resin composites revealed no statistically significant differences (p > 0.05). Among the resin composites, the supra-nano composite (DiaPolisher: 70.1 ± 6.8, Lucida: 72.1 ± 5.5, Diamond Polish: 71.1 ± 3.5, and control: 73.5 ± 5.5) exhibited the highest microhardness values (p < 0.001). No statistically significant differences were observed among the nanofill (DiaPolisher: 65.1 ± 1.4, Lucida: 64.5 ± 0.8, Diamond Polish: 64.2 ± 1.7, and control: 64.3 ± 0.9) and nanohybrid (DiaPolisher: 63.6 ± 3.7, Lucida: 61.1 ± 3.4, Diamond Polish: 63.4 ± 2.2, and control: 62.1 ± 2.4) composites (p > 0.05). Following aging, a statistically significant decrease in the microhardness values of the nanofill, supra-nano, and nanohybrid resin composites was observed (p < 0.05) (Table 4; Fig. 2).
Table 4.
Initial and post-aging microhardness values (VHN) of resin composite groups treated with polishing pastes of different particle sizes
| Resin composite/polishing pastes | Control (No polishing paste) | DiaPolisher (1 μm) | Lucida (Sub-micron) | Diamond polish (0.5 μm) | ||||
|---|---|---|---|---|---|---|---|---|
| Initial | Aged | Initial | Aged | Initial | Aged | Initial | Aged | |
|
Nanofill (3M Filtek Universal Restorative) |
64.3±0.9aA | 60.1±1.7bA | 65.1±1.4aA | 61.9±0.9bA | 64.5±0.8aA | 60.5±1.4bA | 64.2±1.7aA | 61.1±0.9bA |
|
Supra-nano (Estelite Asteria) |
73.5±5.5aB | 61.3±3.7bA | 70.1±6.8aB | 61.3±4.7bA | 72.1±5.5aB | 64.7±3.4bA | 71.1±3.5aB | 60.0±2.6bA |
|
Nanohybrid (G-aenial A’chord) |
62.1±2.4aA | 56.9±2.9bB | 63.6±3.7aA | 56.3±2.1bB | 61.1±3.4aA | 56.6±3.1bB | 63.4±2.2aA | 58.5±4.2bA |
* Among the resin composites, the supra-nano composite exhibited the highest microhardness (p < 0.001). Paste application did not cause a statistically significant difference in the microhardness values of the nanofill, supra-nano and nanohybrid composites (p > 0.05). Following aging, all composite groups demonstrated a significant reduction in microhardness (p < 0.001). Statistical significance was set at p < 0.05. Statistically significant differences in microhardness values among the nanofill, supra-nano, and nanohybrid composites are shown by uppercase letters (A–B), while differences between the polishing methods and aging are shown by lowercase letters (a–b)
Fig. 2.
Initial and post-aging microhardness images of resin composite groups treated with polishing pastes of different particle sizes. a Nanofill (3M Filtek Universal Restorative), b Supra-nano (Estelite Asteria), c Nanohybrid (G-aenial A’chord)
Analysis of the effect of polishing pastes on the surface gloss (GU) of resin composites revealed no statistically significant differences in the nanofill (DiaPolisher: 91.8 ± 2.6, Lucida: 90.7 ± 2.6, Diamond Polish: 90.3 ± 2.1, and control: 90.2 ± 2.9) and supra-nano composites (DiaPolisher: 82.5 ± 5.0, Lucida: 81.5 ± 1.2, Diamond Polish: 82.1 ± 1.7, and control: 80.3 ± 3.2) (p > 0.05). However, in the nanohybrid composite (DiaPolisher: 82.0 ± 3.6, Lucida: 81.6 ± 2.7, Diamond Polish: 82.5 ± 1.8, and control: 64.9 ± 6.6), a statistically significant difference was observed (p < 0.001). Among the resin composites, the supra-nano composite exhibited the highest gloss values (p < 0.001). After the application of polishing pastes, no statistically significant differences in gloss values were found between the nanofill and nanohybrid composites (p > 0.05). Following aging, a statistically significant decrease in the gloss values of all nanofill, supra-nano, and nanohybrid resin composites was observed (p < 0.001) (Table 5).
Table 5.
Initial and post-aging gloss values (GU) of resin composite groups treated with polishing pastes of different particle sizes
| Resin composite/polishing pastes | Control (No polishing paste) | DiaPolisher (1 μm) | Lucida (Sub-micron) | Diamond polish (0.5 μm) | ||||
|---|---|---|---|---|---|---|---|---|
| Initial | Aged | Initial | Aged | Initial | Aged | Initial | Aged | |
|
Nanofill (3M Filtek Universal Restorative) |
90.2±2.9aA | 84.2±3.9bA | 91.8±2.6aA | 87.1±1.9bA | 90.7±2.6aA | 85.6±2.2bA | 90.3±2.1aA | 86.4±1.2bA |
|
Supra-nano (Estelite Asteria) |
80.3±3.2aB | 71.6±3.8bB | 82.5±5.0aB | 78.6±1.9bB | 81.5±1.2aB | 77.4±0.9bB | 82.1±1.7aB | 77.1±3.4abB |
|
Nanohybrid (G-aenial A’chord) |
64.9±6.6aC | 57.6±5.6bC | 82.0±3.6cB | 77.2±3.1dB | 81.6±2.7cB | 77.3±1.8dB | 82.5±1.8cB | 76.6±1.6dB |
*Among the resin composites, the nanofill composite exhibited the highest gloss (p < 0.05). Paste application did not cause a statistically significant difference in the gloss values of the nanofill and supra-nano composites (p > 0.05). Conversely, the nanohybrid composite demonstrated a significant increase in gloss (p < 0.05). Following aging, all composite groups showed a significant reduction in gloss values (p < 0.05). Statistical significance was set at p < 0.05. Statistically significant differences in gloss values among the nanofill, supra-nano, and nanohybrid composites are shown by uppercase letters (A–C), while differences between the polishing methods and aging are shown by lowercase letters (a–d)
Examination of the effect of polishing pastes on the color change (ΔE00) of resin composites revealed statistically significant differences (p < 0.05). The resin composites polished with pastes -nanofill (DiaPolisher: 0.77 ± 0.14, Lucida: 0.77 ± 0.09, Diamond Polish: 0.76 ± 0.06, and control: 1.24 ± 0.14), supra-nano (DiaPolisher: 0.69 ± 0.14, Lucida: 0.62 ± 0.10, Diamond Polish: 0.74 ± 0.08, and control: 1.12 ± 0.10), and nanohybrid (DiaPolisher: 0.80 ± 0.08, Lucida: 0.81 ± 0.08, Diamond Polish: 0.74 ± 0.04, and control: 1.16 ± 0.18)- exhibited significantly less color change compared with the control groups (p < 0.05). No statistically significant differences were found among the polishing pastes (p > 0.05) or among the nanofill, supra-nano, and nanohybrid composite types (p > 0.05). The color change of the composites polished with pastes did not exceed the perceptibility threshold (ΔE00 = 0.8) (Table 6).
Table 6.
Color change values (ΔE₀₀) of resin composite groups treated with polishing pastes of different particle sizes
| Resin composite/polishing pastes | Control (No polishing paste) | DiaPolisher (1 μm) | Lucida (Sub-micron) | Diamond Polish (0.5 μm) |
|---|---|---|---|---|
|
Nanofill (3M Filtek Universal Restorative) |
1.24±0.14aA | 0.77±0.14bA | 0.77±0.09bA | 0.76±0.06bA |
|
Supra-nano (Estelite Asteria) |
1.12±0.10aB | 0.69±0.14bA | 0.62±0.10bA | 0.74±0.08bA |
|
Nanohybrid (G-aenial A’chord) |
1.16±0.18aAB | 0.80±0.08bA | 0.81±0.08bA | 0.74±0.04bA |
* Statistically significant differences in color change (ΔE) values among the nanofill, supra-nano, and nanohybrid composites are shown by uppercase letters (A–B), while differences between the polishing methods and aging are shown by lowercase letters (a–b). A significance level of p < 0.05 was considered
Discussion
In this study, all null hypotheses were accepted, as the use of polishing pastes containing abrasives of different particle sizes after the finishing and polishing system did not result in significant differences in the surface roughness, microhardness, gloss, or color change of the resin composites.
Conventional finishing and polishing protocols consist of a series of abrasives that gradually decrease in coarseness from coarse to fine [6, 25]. The abrasive particles in finishing and polishing systems should be harder than the fillers of the composites, and the abrasive particles should be smaller than the composite fillers to prevent scratches on the composite surface. Therefore, polishing systems use finer abrasives at each step until a high-gloss surface is achieved in order to remove scratches formed by the previous polishing procedures [26]. Polishing is not the only variable affecting the final roughness of a restoration; the filler particle size of the material is also an important factor [27].
Various compounds such as aluminum oxide, silicon dioxide, and diamond abrasives are used in polishing protocols [6]. Some of the instruments used include rubber cups and tips, abrasive polishing discs, and polishing stones. It has been reported that abrasive discs used in multi-step polishing systems are the most effective at achieving the lowest surface roughness values [28]. The use of adjuncts such as systems with added diamond particles or diamond polishing pastes is also effective in achieving surface roughness below 0.2 μm [6].
Alshehri et al. [29] reported that among different finishing and polishing systems (Twist Dia, Occlubrush, and Soflex Spiral), Twist Dia achieved the smoothest surface on resin composites. Scheibe et al. [30] in a study where they applied three different polishing systems to various resin composite materials, found the lowest surface roughness in the group polished with aluminum oxide–impregnated silicone points followed by diamond paste (Enhance, Dentsply + Excel Diamond Paste, FGM) and in the group polished with felt disks and diamond paste (Felt Disk, FGM + Excel Diamond Paste, FGM). Turssi et al. [31] observed that polishing resin composites with Sof-Lex followed by Prisma Gloss aluminum oxide paste resulted in smoother surfaces. Chour et al. [22] found that when different polishing systems (Sof-Lex, Diamond Tips, Astrobrush) were applied to resin composites, aluminum oxide–containing systems produced smoother surfaces compared to diamond polishing systems, due to their smaller abrasive particles.
In this study, the application of polishing pastes with submicron (< 1 μm) (Lucida), 1 μm (DiaPolisher), and 0.5 μm (Diamond Polish) abrasive particles after two-step diamond finishing and polishing spirals (Twist Dia) resulted in lower surface roughness on resin composites. It is considered that no differences were found among the pastes because the diamond particle sizes were all smaller than 1 μm.
Nanohybrid composites containing prepolymerized fillers are susceptible to degradation of the filler–matrix interface due to filler loss, which may lead to higher surface roughness compared to nanofill composites [32, 33]. According to Eguivar et al. [34], when simplified and multi-step polishing systems were applied to nanofill, supra-nano, and nanohybrid resin composites, the nanohybrid group exhibited an increase in surface roughness (Ra, µm) under both polishing protocols. They emphasized that the selection of resin composite material had a greater influence on surface roughness and color stability than the polishing technique itself. Restrepo et al. [35] evaluated two-step (ShapeGuard) and three-step (Astropol) polishing systems applied to nanohybrid resin composites. They concluded that the resin matrix composition played a critical role in determining surface roughness, and that zirconia-filled composites produced smoother surfaces.
Zhang et al. [36], in their study using an aluminum oxide polishing system (Sof-Lex-SL) on nanohybrid, nanofill, and microhybrid composites, reported no significant difference in surface roughness among the groups. Viana et al. [37], stated that when microfill, microhybrid, nanofill, and nanohybrid composites were polished with diamond burs and Sof-Lex discs and then subjected to thermocycling, the type of polishing did not result in significant differences in roughness. In their study, Alvarenga et al. [38], applied different polishing systems (Sof-Lex (40 μm, 24 μm, and 8 μm) + Diamond Polish, and Jiffy (40 μm, 30 μm, and 5 μm) + Diamond Polish) to nanofill, supra-nano, and nanohybrid resin composite groups. They reported that the surface roughness of the nanofill group increased after immersion in water or coffee. Elmarsafy et al. [39], evaluated different polishing systems (Sof-Lex, Diatech Shapeguard, Venus Supra, and Astropol) applied to nanofill, nanohybrid, microfill, and microhybrid resin composites. They found that the nanofill composites exhibited the lowest surface roughness values, while all composite groups demonstrated a significant increase in roughness after thermocycling.
Dennis et al. [40], in their study applying multi-step and single-step polishing systems to microhybrid and nanohybrid composites, reported that the highest surface roughness values were obtained with aluminum oxide polishing systems (One Gloss, Shofu), while the lowest values were obtained with diamond-containing polishing systems (Diatech, Coltene). They also noted that there was no significant difference between microhybrid and nanohybrid composites when multi-step polishing systems were used. In their study, Korkut et al. [41], applied different polishing systems (Sof-Lex (8 μm, 16 μm) + Lucida, Diacomp Twist Plus (40–50 μm, 3–6 μm) + Lucida, Enhance & Pogo (40 μm, 7 μm) + Lucida, and Kenda (30–40 μm) + Lucida) to nanohybrid resin composite specimens (G-aenial A’chord, GC, Japan). They reported that the Sof-Lex and Enhance & Pogo systems were more effective when no additional polishing paste was used, and emphasized that selecting the polishing protocol according to the initial surface roughness of the composite could be beneficial. Sarıcı et al. [42], investigated giomer, nanohybrid, microhybrid, and nanoceramic resin composite groups polished with different polishing systems (OptiDisc, Twist Dia, Enhance & Pogo, and Lucida Shine). They reported that the nanohybrid resin composites polished with the Lucida system exhibited the highest surface roughness values. Neha et al. [43], investigated the effects of different polishing systems on nanohybrid and microhybrid resin composites and found that the nanohybrid composite group exhibited lower surface roughness values. They also reported that atomic force microscopy (AFM) provided better visualization and differentiation of surface irregularities among the tested groups.
When the surface roughness of the resin composites was evaluated using an optical profilometer in this study, the nanofill and supra-nano composites exhibited lower surface roughness values than the nanohybrid composite. Similar to findings in the literature, the application of polishing pastes after the finishing and polishing procedures reduced the surface roughness of the resin composites [41, 42].
An increase in filler particle size improves the strength and surface hardness of resin composites. Furthermore, the type, morphology, distribution, and volume fraction (filler volume/total volume), as well as the concentration of monomers, affect the hardness of the composite [44, 45]. Residual monomers that do not participate in post-polymerization reactions reduce the hardness of materials [26]. Hatipoğlu et al. [46] compared experimental resin composites containing Bis-GMA, UDMA, and Bis-EFMA and reported that Bis-EFMA–based resins exhibited higher microhardness values and have potential to be used as an alternative to Bis-GMA.
Nasoohi et al. [47] reported that in their study where nanohybrid and microhybrid composites were polished with Sof-Lex Pop-On Discs (3 M ESPE) under dry and wet conditions, the nanohybrid group with the highest filler content (87 wt%) exhibited the highest microhardness values after both dry and wet polishing. The increase in filler content enhances the microhardness of resin composites [45]. Erdemir et al. [48] reported that when single-step (Pogo, Dentsply, 20 μm) and multi-step (Sof-Lex Pop-On Discs, 3 M ESPE) polishing systems with different particle sizes were applied to nanofill and nanohybrid composites, higher microhardness values were obtained in the nanohybrid group with the highest filler content (87 wt%).
In this study, the supra-nano resin composite, with the highest filler content (82 wt%), showed greater microhardness values. No differences were found between the microhardness values of nanofill, supra-nano, and nanohybrid composites, regardless of paste application.
Surface gloss is largely influenced by factors such as changes in the reflective properties of the surface texture, and how the specimen is illuminated and observed. Resin composites with smaller filler particles can achieve higher gloss and lower surface roughness when polished with various systems [49, 50]. Generally, as surface roughness increases, random reflection of light also increases, which reduces gloss [51]. However, researchers have also noted that improvements in surface roughness do not always lead to corresponding improvements in gloss, and these outcomes may vary depending on the material [32, 52]. For resin composites, gloss values between 60 and 70 GU are considered clinically acceptable [53].
Dennis et al. [40] reported that in their study with microhybrid and nanohybrid composites polished with multi-step and single-step systems, the highest gloss values were obtained in nanohybrid composites polished with Polishettes™ (Kenda; diamond, silicon carbide, and aluminum oxide abrasives) (96.70 GU) and Diatech™ Shapeguard Spiral (Coltene; diamond abrasives) (90.68 GU), while the lowest gloss values were obtained with the single-step system OneGloss (Shofu; aluminum oxide and silicon oxide abrasives) (36.2–50.7 GU). Zhang et al. [36] reported that when nanofill, nanohybrid, and microhybrid composites were polished with an aluminum oxide abrasive system (Sof-Lex SL, 3M ESPE), nanohybrid and nanofill composites achieved the clinical standard of 53 GU, while the microhybrid composite did not. Chiang et al. [54] stated that gloss values are more strongly associated with the subjective interpretation of surface texture than with the filler composition of resin composites. In this study, polishing paste application increased the gloss of nanohybrid composites, whereas no effect was observed in nanofill and supra-nano composites. After aging, the gloss values of resin composites treated with polishing pastes decreased but remained above clinically acceptable levels.
The chemical composition of the organic matrix and filler content, as well as the finishing and polishing procedures, are critical factors for the color stability and stain resistance of resin composites [55, 56]. Sarıcı et al. [42] reported in their study that the Twist Dia system exhibited the greatest resistance to color change. Karakaş et al. [57] reported that in their study applying different polishing systems (OptraGloss, OptiDisc, Occlubrush, OptraGloss + Diapolisher Paste, OptiDisc + Diapolisher Paste) to resin composites, the least color change was observed in the groups polished with OptiDisc, OptiDisc + Diapolisher Paste, and Occlubrush systems. Alvarenga et al. [38] reported in their study that the supra-nano group exhibited the highest color stability after immersion in water or coffee.
Barakah et al. [7], in their study applying single-step (PoGo, Dentsply/Caulk) and multi-step (Astropol, Ivoclar Vivadent; Hi-Shine, Polydentia SA) polishing systems to nanofill, nanohybrid, and microhybrid composites, reported that although the single-step PoGo system produced the lowest surface roughness, it did not provide the greatest resistance to color changes. These findings are consistent with other reports that the lowest surface roughness does not necessarily correspond to the highest resistance to staining [58, 59]. In this study, nanofill, nanohybrid, and supra-nano composites treated with polishing pastes showed less color change. No statistically significant differences were found among the pastes.
In this study, the groups of nanofill, nanohybrid, and supra-nano resin composites treated with polishing pastes exhibited less color change compared with the untreated groups. No statistically significant differences were observed among the polishing pastes. The use of a paste containing fine diamond abrasives (< 1 μm) after the finishing and polishing procedures was found to produce a smoother composite surface, which is considered to contribute to maintaining color stability.
The organic matrix and its component monomers directly influence color stability due to factors such as degree of conversion and hydrophilicity [60]. Hydrophilic resins tend to absorb more water, which increases the likelihood of staining and negatively affects color stability [61, 62]. Bis-EMA has been associated with lower hydrophilicity potential, leading to reduced water sorption and less extrinsic staining compared to Bis-GMA- and UDMA-based resins [63, 64]. Additionally, composites containing TEGDMA release significantly more monomers in aqueous environments compared to UDMA-based composites, resulting in greater color change [64].
Alkhadim et al. [65], in their study applying a polishing system (Astropol Polishing System, Ivoclar Vivadent) to nanohybrid, microhybrid, and nanoceramic composites, reported that color changes were lower in microhybrid and nanoceramic groups compared to others, with minimal differences between microhybrid and nanohybrid groups. The reduced color change in the nanoceramic group was attributed to Bis-EMA, which has lower hydrophilicity. Jrady et al. [14], in their study applying polishing systems with different abrasive particle sizes (Sof-Lex Discs, 3M ESPE [50 μm, 40 μm, 24 μm, 8 μm], Astropol, Ivoclar Vivadent [36.5 μm, 12.8 μm, 3.5 μm], and Charisma Easyshine, Heraeus Kulzer [5 μm]) to microhybrid, flowable nanohybrid, nanohybrid, and nanofill composites, reported that the least color change was observed in the three-step polishing system (Astropol, Ivoclar Vivadent). Among the composites, the lowest color change was observed in the group containing Bis-MEPP, Bis-EMA, UDMA, and TEDMA, while the highest color change was observed in the group containing Bis-GMA and TEGDMA. Several studies in the literature have reported that Bis-GMA–based resin composites exhibit lower color stability [66, 67]. The nanofill, nanohybrid, and supra-nano composites used in this study contained UDMA monomer, which may explain the similar color change values observed.
Devlukia et al. [9], in their systematic review assessing the influence of polishing procedures on the surface roughness of resin composite restorations, emphasized the need for more robustly designed clinical studies to determine whether specific combinations of resin composites and polishing systems yield superior outcomes. They also highlighted that the findings obtained from in vitro studies should be corroborated with in vivo evidence. The present study has some limitations. It was conducted in vitro and included only one finishing system. Since dental materials in the oral cavity are subjected to various physical and chemical changes and to beverages containing pigments, the findings may not fully represent clinical conditions. Only distilled water was used in this study. Future studies may focus on evaluating the effects of different beverages on the color stability of resin composites polished with various pastes.
Conclusions
Within the limitations of this study: Following the finishing and polishing procedures, a reduction in the surface roughness of the resin composites treated with polishing pastes was observed, whereas no significant differences were found among the pastes. The supra-nano composite with the highest filler content exhibited higher microhardness. Polishing pastes had no effect on the surface microhardness of resin composites. While polishing pastes did not influence the gloss of supra-nano and nanofill composites, they increased the gloss of nanohybrid composites. Resin composites treated with polishing pastes showed less color change. Polishing pastes positively influenced surface roughness, gloss, and color stability of resin composites after aging.
Acknowledgements
Not applicable.
Abbreviations
- VHN
Vickers Hardness Number
- Ra.
Roughness Average
- GU
Gloss Unit
Authors’ contributions
M.B. and N.A.: Study design and drafting manuscript; M.B., B.E and N.A.: Conceived the ideas and data analysis; M.B. and N.A.: Data collection; M.B., B.E, B.E and S.K.: Performing statistical analysis; N.A. and M.B.: Concept and critical revision of the manuscript. All authors have read and approved the manuscript.
Funding
This research has not received any funding.
Data availability
The datasets used and/or analyzed during the current study are available from the corresponding author upon reasonable request.
Declarations
Ethics approval and consent to particpate
This article does not contain any studies with human participants or animals performed by any of the authors
Consent for publication
Not applicable.
Competing interests
The authors declare no competing interests.
Footnotes
Publisher’s Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
References
- 1.Terry DA. Direct applications of a nanocomposite resin system: part 1–The evolution of contemporary composite materials. Pract Proced Aesthet Dent. 2004;16:417–22. [PubMed] [Google Scholar]
- 2.Mitra SB, Wu D, Holmes BN. An application of nanotechnology in advanced dental materials. J Am Dent Assoc. 2003;134:1382–90. [DOI] [PubMed] [Google Scholar]
- 3.Ferracane JL. Resin composite-state of the Art. Dent Mater. 2011;27:29–38. [DOI] [PubMed] [Google Scholar]
- 4.Wysokińska-Miszczuk J, Piotrowska K, Paulo M, Madej M. Composite materials used for dental fillings. Materials. 2024;17:4936. 10.3390/ma17194936. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 5.Perez MM, Hita-Iglesias C, Ghinea R, Yebra A, Pecho OE, Ionescu AM, Hita E. Optical properties of supra-nano spherical filled resin composites compared to nanofilled, nano-hybrid and micro-hybrid composites. Dent Mater J. 2016;35:353–9. [DOI] [PubMed] [Google Scholar]
- 6.Khan A, Hodson N, Altaie A. Polishing systems for modern aesthetic dental materials: A narrative review. Br Dent J. 2024;237:607–13. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 7.Barakah HM, Taher NM. Effect of Polishing systems on stain susceptibility and surface roughness of nanocomposite resin material. J Prosthet Dent. 2014;112:625–31. 10.1016/j.prosdent.2013.12.007. [DOI] [PubMed] [Google Scholar]
- 8.Rodrigues-Junior SA, Chemin P, Piaia PP, Ferracane JL. Surface roughness and gloss of actual composites as polished with different Polishing systems. Oper Dent. 2015;40:418–29. 10.2341/14-014L. [DOI] [PubMed] [Google Scholar]
- 9.Devlukia S, Hammond L, Malik K. Is surface roughness of direct resin composite restorations material and polisher-dependent? A systematic review. J Esthet Restor Dent. 2023;35(6):947–67. [DOI] [PubMed] [Google Scholar]
- 10.Vargas MA, Margeas R. A systematic approach to contouring and Polishing anterior resin composite restorations: a checklist manifesto. J Esthet Restor Dent. 2021;33:20–6. [DOI] [PubMed] [Google Scholar]
- 11.Wheeler J, Deb S, Millar BJ. Evaluation of the effects of Polishing systems on surface roughness and morphology of dental composite resin. Br Dent J. 2020;228:527–32. 10.1038/s41415-020-1370-8. [DOI] [PubMed] [Google Scholar]
- 12.Silva JP, Coelho A, Paula A, Amaro I, Saraiva J, Ferreira MM, Marto CM, Carrilho E. The influence of irrigation during the finishing and Polishing of composite resin Restorations-A systematic review of in vitro studies. Materials. 2021;14:1675. 10.3390/ma14071675. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 13.Bollen CM, Lambrechts P, Quirynen M. Comparison of surface roughness of oral hard materials to the threshold surface roughness for bacterial plaque retention: a review of the literature. Dent Mater. 1997;13:258–69. 10.1016/s0109-5641(97)80038-3. [DOI] [PubMed] [Google Scholar]
- 14.Jrady A, Ragab H, Algahtani FN, Osman E. In vitro study on the impact of various Polishing systems and coffee staining on the color stability of bleach-shaded resin composite. BMC Oral Health. 2024;24:712. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 15.Gedik R, Hürmüzlü F, Coskun A, Özel Bektas Ö, Özdemir AK. Surface roughness of new microhybrid resin-based composites. J Am Dent Assoc. 2005;136:1106–12. [DOI] [PubMed] [Google Scholar]
- 16.Paravina RD, Ghinea R, Herrera LJ, Bona AD, Igiel C, Linninger M, Mar Perez MD. Color difference thresholds in dentistry. J Esthet Restor Dent. 2015;27:1–9. [DOI] [PubMed] [Google Scholar]
- 17.Vichi A, Louca C, Corciolani G, Ferrari M. Color related to ceramic and zirconia restorations: a review. Dent Mater. 2011;27:97–108. [DOI] [PubMed] [Google Scholar]
- 18.Vichi A, Fonzar RF, Goracci C, Carrabba M, Ferrari M. Effect of finishing and Polishing on roughness and gloss of lithium disilicate and lithium silicate zirconia reinforced glass ceramic for CAD/CAM systems. Oper Dent. 2018;43:90–100. [DOI] [PubMed] [Google Scholar]
- 19.Lee YK, Lu H, Oguri M, Powers JM. Changes in gloss after simulated generalized wear of composite resins. J Prosthet Dent. 2005;94:370–6. [DOI] [PubMed] [Google Scholar]
- 20.Park JW, An JS, Lim WH, Lim BS, Ahn SJ. Microbial changes in biofilms on composite resins with different surface roughness: an in vitro study with a multispecies biofilm model. J Prosthet Dent. 2019;122:493e1. [DOI] [PubMed] [Google Scholar]
- 21.Nezir M, Ahisha CD, Özcan S, Üçtaşli MB. The effect of detox solution on color stability, roughness, and microhardness of monochromatic universal composite resins. BMC Oral Health. 2024;24:789. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 22.Chour RG, Moda A, Arora A, Arafath MY, Shetty VK, Rishal Y. Comparative evaluation of effect of different Polishing systems on surface roughness of composite resin: an in vitro study. J Int Soc Prev Community Dent. 2016;6(Suppl 2):S166–70. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 23.Chowdhury D, Mukherjee S, Maity I, Mazumdar P. Surface roughness and microhardness evaluation of composite resin restorations subjected to three different Polishing systems immediately and after 24 h: an in vitro study. J Conserv Dent Endod. 2023;26(6):639–45. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 24.Saati K, Valizadeh S, Rahmaniparast A, Karimi M. In vitro effects of Sof-Lex, Eve, and astropol Polishing systems on composite resin surface roughness after aging. Front Dent. 2024;21:35. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 25.Jefferies SR. The Art and science of abrasive finishing and Polishing in restorative dentistry. Dent Clin North Am. 1998;42:613–27. [PubMed] [Google Scholar]
- 26.Ozdemir B, Ilday NO, Ozdemir SB, Suleyman F, Duymus ZY. The effect of erosive beverages and Polishing systems on the surface properties of nanohybrid composite resin. Niger J Clin Pract. 2022;25:248–54. [DOI] [PubMed] [Google Scholar]
- 27.Hassan AM, Nabih SM, Mossa HM, Baroudi K. The effect of three Polishing systems on surface roughness of flowable, microhybrid, and packable resin composites. J Int Soc Prev Community Dent. 2015;5:242–7. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 28.De Oliveira AG, Rocha RS, Spinola MDS, Batista GR, Bresciani E, Caneppele TMF. Surface smoothness of resin composites after polishing – a systematic review and network meta-analysis of in vitro studies. Eur J Oral Sci. 2023;131:e12921. [DOI] [PubMed] [Google Scholar]
- 29.Alshehri A, Alhalabi F, Mustafa M, Awad MM, Alqhtani M, Almutairi M, Alshabib A. Effects of accelerated aging on color stability and surface roughness of a biomimetic composite: an in vitro study. Biomimetics. 2022;7:158. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 30.Scheibe KGBA, Almeida KGB, Medeiros IS, Costa JF, Alves CMC. Effect of different Polishing systems on the surface roughness of microhybrid composites. J Appl Oral Sci. 2009;17:21–6. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 31.Turssi CP, Saad JR, Duarte SL Jr, Rodrigues AL Jr. Composite surfaces after finishing and Polishing techniques. Am J Dent. 2000;13:136–8. [PubMed] [Google Scholar]
- 32.Antonson SA, Yazici AR, Kilinc E, Antonson DE, Hardigan PC. Comparison of different finishing/polishing systems on surface roughness and gloss of resin composites. J Dent. 2011;39:e9–17. [DOI] [PubMed] [Google Scholar]
- 33.Senawongse P, Pongprueksa P. Surface roughness of nanofill and nanohybrid resin composites after Polishing and brushing. J Esthet Restor Dent. 2007;19:265–73. [DOI] [PubMed] [Google Scholar]
- 34.Eguivar YA, França FM, Turssi CP, Basting RT, Vieira-Junior WF. Effect of simplified or multi-step Polishing techniques on roughness and color stability of resin composites. Am J Dent. 2023;36(6):274–80. [PubMed] [Google Scholar]
- 35.Restrepo AM, Giraldo CA, Torres-López AM, Latorre-Correa F, Ardila CM. Effect of two multi-step Polishing systems on surface characteristics of nanohybrid composite resins: influence of reuse. J Clin Exp Dent. 2025;17(8):e929–35. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 36.Zhang L, Yu P, Wang XY. Surface roughness and gloss of polished nanofilled and nanohybrid resin composites. J Dent Sci. 2021;16:1198–203. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 37.de Oliveira Viana M, Dias AAFA, Vedovello SAS, Flório FM, Motta RHL, Rodrigues JA. Evaluation of different types of Polishing of composite resin surfaces after the removal of metal and ceramic brackets. Braz Dent Sci. 2015;18:102–10. [Google Scholar]
- 38.Alvarenga ACF, Kantovitz KR, Turssi CP, Basting RT, Vieira-Junior WF, França FM. Effect of finishing and Polishing systems on surface roughness and color stability of aesthetic restorations exposed to staining solution. Acta Odontol Latinoam. 2024;37(2):162–71. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 39.Elmarsafy SM, Abdelwahab SA, Hussein F. Influence of Polishing systems on surface roughness of four resin composites subjected to thermocycling aging. Dent Res J (Isfahan). 2023;20:35. [PMC free article] [PubMed] [Google Scholar]
- 40.Dennis T, Zoltie T, Wood D, Altaie A. Reduced-step composite Polishing systems-a new gold standard? J Dent. 2021;112:103769. [DOI] [PubMed] [Google Scholar]
- 41.Korkut B, Alkan E, Öztürk EK, Türkmen C, Tağtekin D. Questioning the effectiveness of composite Polishing systems by crosschecking profilometer and dental microscope outcomes. Sci Rep. 2025;15(1):21118. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 42.Sarıcı T, Dayı B. Evaluation of the effects of different Polishing systems on surface roughness and surface discoloration of various restorative materials. BMC Oral Health. 2025;25(1):978. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 43.Neha N, Bhandari S, Solete P, Choudhari S, Rathod NN, Adimulapu HS. Comparative analysis of the surface roughness of class V composite restorations using a conventional Polishing system and pre-contoured cervical matrices: an in vitro study. Cureus. 2023;15(9):e45901. [DOI] [PMC free article] [PubMed]
- 44.Marghalani HY. Post-irradiation Vickers microhardness development of novel resin composites. Mater Res. 2010;13:81–7. [Google Scholar]
- 45.Tchorz JP, Doll R, Wolkewitz M, Hellwig E, Hannig C. Microhardness of composite materials with different organic phases in deep class II cavities: an in vitro study. Oper Dent. 2011;36:502–11. [DOI] [PubMed] [Google Scholar]
- 46.Hatipoğlu Ö, Turumtay EA, Saygın AG. Evaluation of monomer elution, microhardness, and roughness of experimental dental composite resins prepared from Bis-EFMA, a novel monomer system. Polym Compos. 2022;43(1):584–92. [Google Scholar]
- 47.Nasoohi N, Hoorizad M, Tabatabaei SF. Effects of wet and dry finishing and Polishing on surface roughness and microhardness of composite resins. J Dent. 2017;14:69. [PMC free article] [PubMed] [Google Scholar]
- 48.Erdemir U, Sancakli HS, Yildiz E. The effect of one-step and multi-step Polishing systems on the surface roughness and microhardness of novel resin composites. Eur J Dent. 2012;6:198–205. [PMC free article] [PubMed] [Google Scholar]
- 49.Ryba TM, Dunn WJ, Murchison DF. Surface roughness of various packable composites. Oper Dent. 2002;27:243–7. [PubMed] [Google Scholar]
- 50.Da Costa J, Adams-Belusko A, Riley K, Ferracane JL. The effect of various dentifrices on surface roughness and gloss of resin composites. J Dent. 2010;38:e123–8. [DOI] [PubMed] [Google Scholar]
- 51.Watanabe T, Miyazaki M, Keith Moore B. Influence of Polishing instruments on the surface texture of resin composites. Quintessence Int. 2006;37:61–7. [PubMed]
- 52.Costa JD, Ferracane J, Paravina RD, Mazur RF, Roeder L. The effect of different Polishing systems on surface roughness and gloss of various resin composites. J Esthet Restor Dent. 2007;19:214–24. [DOI] [PubMed] [Google Scholar]
- 53.ADA Professional Product Review. Polishing Syst. 2010;5:2–16. [Google Scholar]
- 54.Chiang YC, Lai EH, Kunzelmann KH. Polishing mechanism of light-initiated dental composite: geometric optics approach. J Formos Med Assoc. 2016;115:1053–60. [DOI] [PubMed] [Google Scholar]
- 55.Blackham JT, Vandewalle KS, Lien W. Properties of hybrid resin composite systems containing prepolymerized filler particles. Oper Dent. 2009;34:697–702. [DOI] [PubMed] [Google Scholar]
- 56.Kim EH, Jung KH, Son SA, Hur B, Kwon YH, Park JK. Effect of resin thickness on the microhardness and optical properties of bulk-fill resin composites. Restor Dent Endod. 2015;40:128–35. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 57.Karakaş SN, Batmaz SG, Çiftçi V, Küden C. Experimental study of Polishing systems on surface roughness and color stability of novel bulk-fill composite resins. BMC Oral Health. 2025;25:74. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 58.Turkun LS, Turkun M. The effect of one-step Polishing system on the surface roughness of three esthetic resin composite materials. Oper Dent. 2004;29:203–11. [PubMed] [Google Scholar]
- 59.Reis AF, Giannini M, Lovadino JR, Ambrosano GM. Effects of various finishing systems on the surface roughness and staining susceptibility of packable composite resins. Dent Mater. 2003;19:12–8. [DOI] [PubMed] [Google Scholar]
- 60.Alawjali SS, Lui JL. Effect of one-step Polishing system on the color stability of nanocomposites. J Dent. 2013;41:e53–61. [DOI] [PubMed] [Google Scholar]
- 61.Mansouri SA, Zidan AZ. Effect of water sorption and solubility on color stability of bulk-fill resin composite. J Contemp Dent Pract. 2018;19:1129–34. [PubMed] [Google Scholar]
- 62.Sideridou I, Tserki V, Papanastasiou G. Study of water sorption, solubility and modulus of elasticity of light-cured dimethacrylate-based dental resins. Biomaterials. 2003;24:655–65. [DOI] [PubMed] [Google Scholar]
- 63.Kerby RE, Knobloch LA, Schricker S, Gregg B. Synthesis and evaluation of modified urethane dimethacrylate resins with reduced water sorption and solubility. Dent Mater. 2009;25:302–13. [DOI] [PubMed] [Google Scholar]
- 64.Pires-de FDCP, Garcia LDFR, Roselino LDMR, Naves LZ. Color stability of silorane-based composites submitted to accelerated artificial ageing - an in situ study. J Dent. 2011;39:e18–24. [DOI] [PubMed] [Google Scholar]
- 65.Alkhadim YK, Hulbah MJ, Nassar HM. Color shift, color stability, and post-polishing surface roughness of esthetic resin composites. Materials. 2020;13:1376. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 66.Hatipoğlu Ö, Turumtay EA, Saygın AG, Hatipoğlu FP. Evaluation of color stability of experimental dental composite resins prepared from bis-efma, a novel monomer system. J Photopolym Sci Technol. 2021;34(3):297–305. [Google Scholar]
- 67.Varlı Tekingür E, Özer E. Investigation of the color change on Nano-Hybrid composite resin caused by Non-Hydrogen peroxide whitening mouthwashes. J Endod Restor. 2025;3(2):18–22 .
Associated Data
This section collects any data citations, data availability statements, or supplementary materials included in this article.
Data Availability Statement
The datasets used and/or analyzed during the current study are available from the corresponding author upon reasonable request.

