Abstract
Introduction
Military standards favor clean shaven faces in soldiers to reinforce daily disciplinary habits and uniformity and ensure a proper seal of gas masks. In recent years, military beard policies have provided medical and religious exceptions. It has been anecdotally observed that Arctic warriors grow out their beards for added advantage in the extreme cold, but this has not been previously investigated from a thermoregulatory or frostbite injury protection perspective.
Materials and Methods
Validated mathematical models and principles of biophysics were used to predict thermal responses for a standard man with varied levels of facial hair during rest (116W) and moderately active (350W) in 3 environmental conditions, mild heat stress (24 °C; 60% relative humidity (%, RH)), cold stress (−24 °C; 70% RH), and in extreme cold (−45 °C; 75% RH). Modeling was used to compare predicted times to reach core body temperatures and skin temperatures although clean shaven (B0), and in 3 progressively increased levels of facial hair (B1, B2, and B3). Core body temperature was assessed during heat stress conditions, while skin temperatures were assessed in cold and extreme cold conditions.
Results
Using existing thermoregulatory models, we determined that full beards compared to smooth shaven skin did not provide a significant advantage to protection of core temperature. However, finite elements modeling of thermographic changes in skin temperature predicted significant protection against frostbite injury to the face, and this was additional to protection provided by standard military balaclava wear in the Arctic.
Conclusions
We conclude that beards provide a lethality advantage to male soldiers operating in the cold, enhancing military exploitation of extreme cold environments.
INTRODUCTION
Mustaches and beards were common among soldiers in the nineteenth century and were sometimes even seen as a status symbol. However, during World War I, the US military began implementing policies prohibiting beards. Some exceptions existed for many years; for example, the US Coast Guard didn’t prohibit beards until 1986. More recently, the US Army eased the policy to implement religious exemptions. However, to date, beards have generally not been authorized in the military except for specific waivers for medical reasons (e.g., pseudofolliculitis barbae) or for approved religious exemptions. The generally stated basis for beard prohibition in the modern Army is to ensure proper protective mask fit but it also serves discipline and uniformity standards and may address personal hygiene concerns.1 In Arctic operations, however, beards may present specific benefits to the Warfighter during extreme environmental stress. Facial frostbite is a significant risk in the extreme cold; although no adequate epidemiological database of cold weather injuries currently exists, there have been published case series, documented observations of cheek frostbite scars in polar dwellers, and frequent reports of facial cold injury in recent US Army exercises indicating that this is a relatively common threat.2 This report provides quantitative comparisons of the thermal benefits of beards during cold weather operations.
Human beards are an androgen-dependent secondary sexual characteristic that also have a genetic variance in pattern and density.3 It has been observed that polar explorers often sport full beards during their sojourns in the cold, perhaps because of the inconvenience of shaving in austere conditions but also demonstrating that beards provide additional health and performance protection in the cold. Although the area represented by the most expansive beard coverage represents a relatively small share of the human body surface area (BSA), there may be a significant evolutionary advantage in human ability to exploit extreme cold environments. Male baldness has been suggested to be an evolutionary adaptation to compensate for the increased heat retention of male beards.4 An adult human head accounts for ∼9% of the total surface area of an individual (∼4.5% anterior; ∼4.5% posterior). For the average male Soldier with a BSA of 1.87 m2 (height, 172 cm; body mass, 75 kg), the head represents approximately 0.17 m2. A beard can account for up to ∼20-25% of this surface area. Although this is a relatively small proportion of the total BSA, the beard configuration area is often the most exposed portion of the body and may represent an important source of body heat loss and vulnerability to cold injury.
As an informative analog to facial hair thermoregulatory effects, Lasisi et al examined heat loss from the head. A comparison between a “no hair” (scalp) condition and various hair types (i.e., straight, curled, tightly curled) demonstrated similarities in terms of heat loss in varied conditions (wet, dry, and wind).5–7 Extrapolating these findings to bearded faces, we assume a consistent thermal benefit of a beard compared to bare skin. An important difference between scalp hair and facial hair is the structure, measured by diameter. Facial hair can be nearly twice as thick, at approximately 0.1 mm but scalp and beard hair grow at a similar pace.8 Beard hair grows at 0.3-0.5 mm per day8,9 but pigmentation and endogenous factors can significantly affect this; for example, white beard hair can grow as fast as 1.12 mm per day compared to pigmented hair (up to 0.47 mm per day).10 Based on face and hair growth morphology, a series of different beard patterns have been described.11 However, although beard growth regions and the surface area coverage can vary between individuals, mapping these regions shows that the total potential beard-covered facial surface area is relatively consistent across individuals.12 This allows us to make some generalizations for beard representations in biophysical modeling.
METHODS
Design
This study did not involve the use of human subjects. The study relied on previously validated human-based predictive models to estimate thermal and injury outcomes. Based on calculated values of assumed beard growth and hair structures shown in Figure 1, mathematical models were used to describe thermal properties for a range of environmental conditions.
Figure 1.
Estimated thermal insulation of 3 levels of added facial hair (B1-B3).
Biophysical models of thermoregulation and injury
To give a range of exposure differences, both a heat stress model, the Heat Strain Decision Aid (HSDA)13–16 and a cold stress model, the Cold Weather Ensemble Decision Aid (CoWEDA)17–20 were used for this analysis. Finite element analyses were also used to provide a higher resolution graphical representation of facial skin temperature based on a bio-heat transfer model for frostbite prediction (FETM),21–24 using the same heat stress, cold, and extreme cold conditions modeled above although at rest and active.
Modeling assumptions
Inputs for modeling assumptions included a standard healthy male, normally hydrated, height 175 cm, body mass 83.5 kg, and a BSA of 1.99 m2.25,26 Modeled environmental conditions included ambient temperature (Ta, °C), relative humidity (RH, %), mean radiant temperature (Tmr, °C), and wind velocity (V, m/s). Conditions chosen were made based on a range of warm and cold conditions often observed in summer (10 to 24 °C) and winter (−10 to −24 °C) of Alaska. Mild heat stress was modeled based on the warmest of these ranges (24 °C), cold stress for the coldest of the ranges (−24 °C), and an extreme cold condition was chosen for context (−45 °C). Modeled activities were set to a resting condition (∼116 W) and at moderate activity (350 W) for both the heat stress and cold stress conditions, while only a resting state was used for the extreme cold condition. For both the cold and extreme cold stress conditions, lighter clothing was used to increase the level of stress in the modeled responses (i.e., mild cold weather clothing for moderate cold conditions and moderate cold weather clothing for the extreme cold conditions).
Beard conditions
Using some principles outlined by Lasisi et al5–7 along with some previously calculated mammalian hair/fur factors we can predict the amount of thermal insulation provided by increased thickness of facial hair (beards).27–29 The thermal resistance of a given beard (Rbeard) can be calculated based on thickness (beardthick) using some reference of these repurposed equations originally used for estimating canine fur thickness,30,31 below:
Figure 1 outlines estimated (dry) thermal insulation based on beard thickness.
Although our current thermal resistance equations above account for beard thickness variations, we acknowledge that hair density and individual hair characteristics (including curl diameter and cross-sectional area) may further influence thermal properties. These equations were derived from mammalian fur models and implicitly incorporate average density assumptions. Future modeling approaches could enhance these relationships by incorporating hair density (n, hairs/m2) and individual hair cross-sectional area (Ahair) through effective thermal conductivity calculations, such as:
where φhair represents the volume fraction of hair within the beard structure.
These enhanced modeling approaches would be particularly relevant for applications requiring precise individual-level predictions, though our current thickness-based equations provide sufficient accuracy for the population-level thermal protection assessments presented in this study.
RESULTS
Biophysical Analysis
Biophysical analyses using HSDA and CoWEDA models demonstrated a negligible impact of beards (with a potential 25% of face coverage) on body core temperature. For comparison purposes, the more pronounced exposures were simulated for each of the conditions; heat stress was modeled in warmer of temperatures (24 °C), cold stress for the colder (−24 °C), and extreme cold condition (−45 °C) (Table 1).
Table 1.
Modeled Conditions During Mild Heat Stress, Cold Stress, and Extreme Cold Stress Conditions
| Condition | Activity (watts) | Rest (116W) |
Active (350W) |
||||||
|---|---|---|---|---|---|---|---|---|---|
| Beard number | B0 | B1 | B2 | B3 | B0 | B1 | B2 | B3 | |
| Beard (clo) | 0.0 (bare skin) | 0.35 | 0.73 | 1.15 | 0.0 (bare skin) | 0.35 | 0.73 | 1.15 | |
| Mild heat stress conditions. (24 °C; 60% RH; 1 m/s) | Clothing |
|
|||||||
| Total clo with beard | 1.11 | 1.117 | 1.125 | 1.133 | 1.11 | 1.117 | 1.125 | 1.133 | |
| Time to body core temperature (Tc) 38 °C (Δbaseline) | 81 minutes | 81 minutes (Δ0) | 81 minutes (Δ0) | 81 minutes (Δ0) | 35 minutes | 35 minutes (Δ0) | 35 minutes (Δ0) | 35 minutes (Δ0) | |
| Tc (°C) at 180 minutes | 38.23 °C | 38.23 °C | 38.23 °C | 38.23 °C | 39.04 °C | 39.04 °C | 39.04 °C | 39.04 °C | |
| Cold stress conditions (−24 °C; 70% RH; 1 m/s) | Clothing | Mild cold weather clothing included: Cold Weather (CW) Cap, Gen III ECWCS Lightweight Cold Weather Undershirt, FRACU Jacket, Gen III ECWCS Fleece Cold Weather Jacket, Army Combat Glove, Gen III ECWCS Lightweight Cold Weather Drawers, FRACU Pants, Combat Boots | |||||||
| Time for head Tsk to reach 25 °C (Δbaseline) | 25 minutes | 40 minutes (Δ15) | 840 minutes (Δ800) | 1,145 minutes (Δ1120) | |||||
| Time for head Tsk to reach 20 °C (Δbaseline) | 770 minutes | 1,015 minutes (Δ245) | 1,135 minutes (Δ365) | 1,225 minutes (Δ455) | |||||
| Tsk head (°C) at 180 minutes | 21 °C | 24 °C | 26 °C | 28 °C | |||||
| Time for head Tsk to reach 28 °C (Δbaseline) | 15 minutes | 25 minutes (Δ10) | 30 minutes (Δ15) | 55 minutes (Δ40) | |||||
| Time for head Tsk to reach 26 °C (Δbaseline) | 20 minutes | 35 minutes (Δ15) | 150 minutes (Δ130) | N/A | |||||
| Time for head Tsk to reach 21 °C (Δbaseline) | 110 minutes | N/A | N/A | N/A | |||||
| Tsk head (°C) at 120 minutes | 21 °C | 24 °C | 27 °C | 28 °C | |||||
| Extreme cold stress conditions (−45 °C; 75% RH; 3 m/s) | Beard condition—Head with beard and balaclava (clo) | 0.69 | 1.04 | 1.42 | 1.84 | ||||
| Clothing | Moderate cold weather clothing included: Lightweight Balaclava, Gen III ECWCS Midweight Cold Weather Shirt, FRACU Jacket, Gen III ECWCS Fleece Cold Weather Jacket, Gen III ECWCS Cold Weather Wind Jacket, Standard Intermediate Cold/Wet Glove (ICWG), Gen III ECWCS Midweight Cold Weather Drawers, FRACU Pants, and Cold Weather (CW) Combat Boot | ||||||||
| Time for head Tsk to reach 25 °C (Δbare skin) [ΔB0+] | 19 minutes (Δ17) | 28 minutes (Δ26) [Δ9] | 50 minutes (Δ48) [Δ31] | 130 minutes (Δ128) [Δ111] | |||||
| Time for head Tsk to reach 20 °C (Δbare skin) [ΔB0+] | 39 minutes (Δ36) | 250 minutes (Δ247) [Δ211] | 590 minutes (Δ587) [Δ551] | 655 minutes (Δ652) [Δ616] | |||||
| Time for head Tsk to reach 15 °C (Δbare skin) [ΔB0+] | 550 minutes (Δ545) | 640 minutes (Δ645) [Δ90] | 705 minutes (Δ700) [Δ155] | N/A | |||||
| Tsk head (°C) at 180 minutes | 18 °C | 21 °C | 23 °C | 25 °C | |||||
Mild heat stress
Table 1 describes the heat stress simulated inputs and responses based on bearded condition (B0, B1, B2, and B3) at both rest (116W) and moderately active (350W). Total insulation (clo) values are displayed for each condition, incorporating the proportional increase made by the added beard insulation. As skin temperature is less of a concern in heat stress,4,33 a focus was made on times to reach meaningful body core temperatures (Tc) indicative of thermal stress (38 °C) as well as the Tc for each condition after 180 minutes of exposure. These conditions are each shown graphically in Figure 2A. Given the minor impact of thermal insulation on the total individual, there is a negligible impact on heat stress across each condition relative to the given work rate (i.e., there is relatively no difference between B0 and B3). While there is a very minor change noticeable when data is observed at high resolution (e.g., out to 4 decimal places); this does not translate to any meaningful difference. Additionally, even over an extended period of 180 minutes, there is very little change in Tc (Table 1; Figure 2A).
Figure 2.
Comparison of body core temperature (Tc) responses during rest (116W) and moderately active (350W) in heat stress conditions (24 °C; 60% RH; 1 m/s) using the Heat Strain Decision Aid (HSDA), (A), skin temperature responses in cold stress conditions (−24 °C; 70% RH, 1 m/s wind) at rest (116W) (B) during moderately active (350W) (C), and at rest (116W) in extreme cold conditions (−45 °C; 75% RH; 3 m/s) (D) using the Cold Weather Ensemble Decision Aid (CoWEDA).
Moderate cold stress
Cold stress was modeled at rest (116W) and while moderately active (350W) (Table 1). Each condition was modeled with a focus on cold stress specifically simulated as skin temperatures (Tsk) based on bearded condition (B0, B1, B2, and B3) as well as a comparison of times to the baseline (B0; no beard) condition and comparison of head Tsk after 180 minutes of exposure. Total head Tsk was used for this modeling, as the CoWEDA method treats the head as a single segment, and currently does not allow for isolating of regions of the head or face. The thermal responses to each condition are graphically shown for both rest (Figure 2B) and moderate activity (Figure 2C). During the resting exposure (Figure 2B), there are 2 observable sharp declines in Tsk; the first within the early exposure (<10 minutes) as Tsk begins to cool and then later in each exposure (>800 minutes) when Tsk begins to cool down further because of total body temperature (e.g., Tc) begin to fall more drastically. This same affect is not observed during the active exposure (Figure 2C), as total body temperature remains elevated, allowing for compensatory heat retention. Both rest and active data (Table 1) show progressive benefit in Tsk with increases in beard conditions (B1, B2, and B3).
Extreme cold stress
For context and comparison, a simulated extreme cold condition was modeled only at rest (116W) (Table 1). Modeled conditions were made based on cold stress simulated as head Tsk based on a face covered with a balaclava and bearded conditions (B0, B1, B2, and B3). Additionally, a bare skin prediction was calculated for comparison. Each simulated condition was calculated to reach progressive Tsk values (25, 20, and 15 °C) and comparisons were made to the added time benefit provided by each condition to bare skin as well as to the balaclava only. The thermal responses to each condition are graphically shown in Figure 2D. Similar to the moderate cold stress condition, the 2 observable sharp declines relate to the initial onset of Tsk cooling (immediately) as well as later in each exposure (>500 minutes) when total body temperatures begin to decline. Table 1 and Figure 2D show the progressive benefits in Tsk with increases in face covering and bearded condition (B0, B1, B2, and B3). Although in each condition there is a progressive cooling of the head Tsk; it is notable that in the more insulated condition (B3 + balaclava) Tsk does not reach 15 °C after more than 720 minutes (12 hours) of simulated exposure.
Face Injury Risk
Finite elements modeling predicts greater protection from frostbite injury as well as comfort improvements for beards during cold exposure.
Finite element analyses during cold stress
Finite element analyses were used to provide a higher resolution graphical representation of facial skin temperature based on the same heat stress, cold, and extreme cold conditions modeled above at rest and active. Figure 3 shows graphics for heat stress (panel 3a), cold stress (panel 3b), and extreme cold (panel 3c) each highlight the progressive increase in face skin temperature because of the added insulation from the beards. Within each panel, shown are the graphically modeled comparison between bearded conditions at rest (top of each panel) and these same conditions during moderate activity (bottom of each panel).
Figure 3.
Finite element analyses of facial skin temperature responses during rest (116W) and moderately active (350W) in heat stress conditions (24 °C; 60% RH; 1 m/s) (A), cold stress conditions (−24 °C; 70% RH, 1 m/s wind) (B), and in extreme cold conditions (−45 °C; 75% RH; 3 m/s) (3c).
Given the natural thermoregulatory process of vasodilation (i.e., larger skin blood flow in the extremities) there is a less pronounced response during the heat stress condition (Figure 3A), as there is less surface area in a cold contrast. Figure 3B and C on the other hand, show a more pronounced difference between the bearded areas and the uncovered face. Additionally, these graphics show the increasing levels of insulation provided by the progressive increase in bearded insulation (B0, B1, B2, and B3), where added beard enables greater heat retention (seen as darker coloring in the graphics).
DISCUSSION
These mathematically-based analyses using validated US Army biophysical models suggest that facial hair provides a warfighter advantage in the Arctic. The primary benefit is maintenance of facial skin temperature and prevention of facial frostbite. There was no predicted effect on whole body core temperature, but the HSDA model has not been developed to predict head temperature as a separate segment, while the CoWEDA model uses the entire head input rather than a portion (currently unable to isolate regions such as bearded area of the face). Protection of brain temperature is a critical survival function. Other research has suggested that regulation of human head temperature is important enough that 2 androgen-dependent functions in men, balding and beard growth, are evolutionarily interdependent, with beards compensating for heat loss from balding heads.4 This head modeling shortfall is a limitation of the present work.
This modeling effort also demonstrated that wear of a balaclava was helpful but larger beards provided additional face protection. Emollients applied to the face have been considered as protective measures but were not effective and may even increase facial frostbite, with some that actually cool the skin and others that provide a false sense of warmth and protection.2
The thermal insulation effects demonstrated in Figure 1 (B1-B3 conditions) represent thickness-based modeling that captures the primary thermal resistance mechanism. However, the variability in individual beard characteristics (e.g., hair density, curl pattern, and individual hair diameter), may create additional thermoregulation effects not fully captured in our current model. While our biophysical analyses using HSDA and CoWEDA showed negligible impact of beards on body core temperature (Figure 2A), the local skin temperature protection effects (Figures 2B-D and 3B and C) demonstrate meaningful benefits for preventing superficial cold-related injuries, with beards providing measurable time-to-cooling protection. The more pronounced differences between bearded and uncovered facial areas during cold exposure suggesting that density variations may influence the magnitude of local thermal protection, particularly for superficial cold-related skin injury prevention.
The primary reason not to have beards in the military is to ensure a proper fit of the gas mask in a chemical, biological, radiological, nuclear, and explosives (CBRNE) environment and it has been well established that any significant facial hair compromises the tight fit required for proper protection.1 Bearded individuals may face challenges in achieving the maximal necessary level of protection, raising concerns about their safety and operational effectiveness. In civilian clinical settings, N95 masks appear to be an exception, as they seem to maintain their effectiveness even when worn by bearded individuals.34 This is likely because of differences in mask design and the specific requirements for achieving an adequate seal. However, CBRN protective postures are likely to be different in extreme cold and arctic operational environments and mask fit in these conditions may be of lesser concern. This may be a tradeoff in Arctic operations where the use of some masks may be complicated by immediate lens fogging from breath and ice accumulation around any exhalation ports. The military mission would determine this tradeoff. In operational environments where CBRN threats emerge, facial hair can be shaved off to ensure proper mask seal. This offers a flexible policy option, particularly for Arctic deployments.
From an operational perspective, beards provide thermal value by adding insulation to the face in cold and extreme cold conditions. This likely enables better protection from cold injuries (e.g., frostbite) and offers additional thermal comfort by keeping the face warmer. However, in mild-heat stress conditions, this value is less significant, as the face may become warmer and less thermally comfortable. Supported in part by the work of Lasisi,7 who has explored the protective benefits of scalp hair, beards may offer some thermally-related health benefits, such as providing an additional level of protection against higher ultraviolet exposure common in cold regions with reflective radiative exposure (e.g., potential reduction in skin cancer).
Several beard characteristics warrant future investigation to enhance thermal modeling accuracy. Our current thickness-based approach does not explicitly account for (1) hair density variations across individuals and ethnic groups, (2) curl diameter effects on air trapping efficiency, or (3) individual hair cross-sectional properties. Rationally integrating these parameters into predictive models requires validation against our established biophysical modeling frameworks (HSDA, CoWEDA) to ensure practical relevance. Additionally, given facial hair can be nearly twice as thick as scalp hair (approximately 0.1 mm), and considering the demonstrated local thermal protection effects shown in our cold stress simulations, future work should focus on developing density-corrected thermal resistance equations, while maintaining compatibility with existing environmental physiology modeling tools. Integration of curl diameter effects and hair cross-sectional variations into thermal resistance calculations would benefit from empirical validation studies measuring actual beard thermal properties across diverse populations.
Other constraints of the study. Additionally, testosterone influences speed of growth and thickness of beards, accounting for some of the individual variability.35,36 This factor could be theoretically modified during stressful military activities, where testosterone (and the related beard growth) may be reduced by physical (metabolic) stress.37,38
CONCLUSIONS
Biophysical analyses show minimal differences on the overall impact of beards on thermal responses (i.e., negligible impact on body core temperature). However, modeling data suggest greater protection from superficial cold related skin injuries (i.e., frostbite) as well as comfort improvements for beards during cold exposure. This review highlights some considerations for the potential values in adjustment of beard grooming standards for positive operational value. Analyses from this work provide rationale for a potential change to standards during deployment to cold locations, especially for extreme cold conditions such as the Arctic.
ACKNOWLEDGMENTS
In a profession where winning matters, those that serve deserve the best we can provide. Our military service members operate in every ‘clime and place.’
Contributor Information
Adam W Potter, Thermal and Mountain Medicine Division, United States Army Research Institute of Environmental Medicine (USARIEM), Natick, MA 01760, United States.
Juliette I Jacques, Thermal and Mountain Medicine Division, United States Army Research Institute of Environmental Medicine (USARIEM), Natick, MA 01760, United States; Oak Ridge Institute for Science and Education (ORISE), Oak Ridge, TN 37830, United States.
Madeline M Poley-Bogan, Thermal and Mountain Medicine Division, United States Army Research Institute of Environmental Medicine (USARIEM), Natick, MA 01760, United States; Oak Ridge Institute for Science and Education (ORISE), Oak Ridge, TN 37830, United States.
Christopher L Chapman, Thermal and Mountain Medicine Division, United States Army Research Institute of Environmental Medicine (USARIEM), Natick, MA 01760, United States; Oak Ridge Institute for Science and Education (ORISE), Oak Ridge, TN 37830, United States.
C O L Karl E Friedl, Office of the Senior Scientist, United States Army Research Institute of Environmental Medicine (USARIEM), Natick, MA 01760, United States.
FUNDING
Funding for this work has been provided by US Army Medical Research and Development Command (USAMRDC), Military Operational Medicine Research Program (MOMRP).
CONFLICT OF INTEREST STATEMENT
The authors have no conflicts of interest.
DATA AVAILABILITY
All data are provided within the manuscript.
INSTITUTIONAL REVIEW BOARD
None declared.
INSTITUTIONAL ANIMAL CARE AND USE COMMITTEE
None declared.
INSTITUTIONAL CLEARANCE
Approved for public release.
INDIVIDUAL AUTHOR CONTRIBUTION STATEMENT
A.W.P. and K.E.F. designed the research, A.W.P., J.I.J., M.M.P.-B., C.L.C., and K.E.F. analyzed data, and wrote the paper. A.W.P. and K.E.F. both have shared responsibility for final content. All authors read and approved the final manuscript.
AI-GENERATED IMAGE DISCLOSURE STATEMENT
Figure 1 was created using artificial intelligence image generation technology [OpenAI, ChatGPT 4o]. This AI-generated is entirely synthetic, created for illustrative purposes, and does not represent or resemble any real individual.
REFERENCES
- 1. Nam H, Kang J, Lee C, Kim S. The effect of hair and beard on the airtightness of gas masks: a quantitative study using SMARTMAN. J Adv Mil Stud. 2024;7:43–61. 10.37944/jams.v7i1.236 [DOI] [Google Scholar]
- 2. Lehmuskallio E, Rintamäki H, Anttonen H. Thermal effects of emollients on facial skin in the cold. Acta Derm Venereol. 2000;80:203–7. 10.1080/000155500750042989 [DOI] [PubMed] [Google Scholar]
- 3. Garn SM. Types and distribution of the hair in man. Ann NY Acad Sci. 1951;53:498–507. 10.1111/j.1749-6632.1951.tb31952.x [DOI] [PubMed] [Google Scholar]
- 4. Cabanac M, Brinnel H. Beards, baldness, and sweat secretion. Eur J Appl Physiol Occup Physiol. 1988;58:39–46. 10.1007/BF00636601 [DOI] [PubMed] [Google Scholar]
- 5. Lasisi T, Ito S, Wakamatsu K, Shaw CN. Quantifying variation in human scalp hair fiber shape and pigmentation. Am J Phys Anthropol. 2016;160:341–52. 10.1002/ajpa.22971 [DOI] [PubMed] [Google Scholar]
- 6. Lasisi T, Smallcombe J, Shriver MD, Kenney WL, Havenith G, Jablonski NG. Hair fiber morphology and function: at the intersection of anthropology, physiology, and engineering. FASEB J. 2020;34:1– 10.1096/fasebj.2020.34.s1.03166 [DOI] [Google Scholar]
- 7. Lasisi T, Smallcombe JW, Kenney WL, et al. Human scalp hair as a thermoregulatory adaptation. Proc Natl Acad Sci USA. 2023;120:e2301760120. 10.1073/pnas.2301760120 [DOI] [PMC free article] [PubMed] [Google Scholar]
- 8. Maurer M, Rietzler M, Burghardt R, Siebenhaar F. The male beard hair and facial skin–challenges for shaving. Int J Cosmet Sci. 2016;38:3–9. 10.1111/ics.12328 [DOI] [PubMed] [Google Scholar]
- 9. Myers RJ, Hamilton JB. Regeneration and rate of growth of hairs in man. Ann NY Acad Sci. 1951;53:562–8. 10.1111/j.1749-6632.1951.tb31957.x [DOI] [PubMed] [Google Scholar]
- 10. Nagl W. Different growth rates of pigmented and white hair in the beard: differentiation vs. proliferation? Br J Dermatol. 1995;132:94–7. 10.1111/j.1365-2133.1995.tb08631.x [DOI] [PubMed] [Google Scholar]
- 11. Souza SEG, Speranzini M. Morphological Classification of Beard Hair in Men. Paper presented at: Hair Transplant Forum International; 2024.
- 12. Durgun U, Ergün SS, Gayretli Ö, Kelahmetoğlu O, Çamli MF. Anatomical landmarks of the beard region. Dermatol Surg. 2021;47:1486–90. 10.1097/DSS.0000000000003193 [DOI] [PubMed] [Google Scholar]
- 13. Potter AW, Blanchard LA, Friedl KE, Cadarette BS, Hoyt RW. Mathematical prediction of core body temperature from environment, activity, and clothing: the heat strain decision aid (HSDA). J Therm Biol. 2017;64:78–85. 10.1016/j.jtherbio.2017.01.003 [DOI] [PubMed] [Google Scholar]
- 14. Potter AW, Hunt AP, Cadarette BS, et al. Heat Strain Decision Aid (HSDA) accurately predicts individual-based core body temperature rise while wearing chemical protective clothing. Comput Biol Med. 2019;107:131–6. 10.1016/j.compbiomed.2019.02.004 [DOI] [PubMed] [Google Scholar]
- 15. Potter AW, Looney DP, Gonzalez JA, et al. Heat Strain Decision Aid (HSDA): Review of Input Ranges, Default Values, and Example Inputs and Outputs for Verification of External Implementation. US Army Research Institute of Environmental Medicine, Natick, MA, 01760, USA, Technical Report; 2021.
- 16. Tharion WJ, Yokota M, Karis AJ, Potter AW. Accuracy of the Heat Strain Decision Aid (HSDA) during Ranger Training Brigade’s Road March Exercise. US Army Research Institute of Environmental Medicine, Natick, MA, 01760, USA, Technical Report, T21-06; 2021.
- 17. Potter A, Looney D, Xu X, Santee W, Srinivasan S. Modeling thermoregulatory responses to cold environments. In: Hypothermia. IntechOpen; 2018. [Google Scholar]
- 18. Xu X, Rioux T, Gonzalez J, et al. Development of a Cold Injury Prevention Tool: The Cold Weather Ensemble Decision Aid (CoWEDA). US Army Research Institute of Environmental Medicine, Natick, MA, 01760, USA, Technical Report; 2019.
- 19. Potter AW, Looney DP, Santee WR, et al. Validation of new method for predicting human skin temperatures during cold exposure: The Cold Weather Ensemble Decision Aid (CoWEDA). Inform Med Unlocked. 2020;18:100301. 10.1016/j.imu.2020.100301 [DOI] [Google Scholar]
- 20. Xu X, Rioux TP, Gonzalez J, et al. A digital tool for prevention and management of cold weather injuries—Cold Weather Ensemble Decision Aid (CoWEDA). Int J Biometeorol. 2021;65:1415–26. 10.1007/s00484-021-02113-0 [DOI] [PMC free article] [PubMed] [Google Scholar]
- 21. Jacques J, Rioux T, Xu X, Castellani J. Human Thermoregulation and Spatial Temperature for Frostbite Prediction with Bio-Heat Transfer Model; 2024.
- 22. Gutierrez S, Jacques J, Rioux T, Castellani J, Xu X. Development of Female and Male Thermoregulatory Models (FETM) using COMSOL; 2024.
- 23. Castellani MP, Rioux TP, Castellani JW, Potter AW, Xu X. A geometrically accurate 3 dimensional model of human thermoregulation for transient cold and hot environments. Comput Biol Med. 2021;138:104892. 10.1016/j.compbiomed.2021.104892 [DOI] [PubMed] [Google Scholar]
- 24. Castellani MP, Rioux TP, Castellani JW, Potter AW, Notley SR, Xu X. Finite element model of female thermoregulation with geometry based on medical images. J Therm Biol. 2023;113:103477. 10.1016/j.jtherbio.2023.103477 [DOI] [PubMed] [Google Scholar]
- 25. Looney DP, Sanford DP, Li P, Santee WR, Doughty EM, Potter AW. Formulae for calculating body surface area in modern US Army Soldiers. J Therm Biol. 2020;92:102650. 10.1016/j.jtherbio.2020.102650 [DOI] [PubMed] [Google Scholar]
- 26. Looney DP, Potter AW, Arcidiacono DM, Santee WR, Friedl KE. Body surface area equations for physically active men and women. Am J Hum Biol. 2023;35:e23823. 10.1002/ajhb.23823 [DOI] [PubMed] [Google Scholar]
- 27. Folk GE. Textbook of Environmental Physiology. Lea & Febiger; 1974. [Google Scholar]
- 28. Hammel HT. Thermal properties of fur. Am J Physiol. 1955;182:369–76. 10.1152/ajplegacy.1955.182.2.369 [DOI] [PubMed] [Google Scholar]
- 29. Schmidt-Nielsen K. Temperature regulation In: Animal Physiology: Adaptation and Environment. 2nd ed. Cambridge: Cambridge University Press; 1979:241–300. [Google Scholar]
- 30. Berglund LG, Yokota M, Santee WR, et al. Predicted Thermal Responses of Military Working Dog (MWD) to Chemical, Biological, Radiological, Nuclear (CBRN) Protective Kennel Enclosure. US Army Research Institute of Environmental Medicine, Natick, MA, 01760, USA, Technical Report, T11-03, 2011. [Google Scholar]
- 31. Potter AW, Berglund LG, O’Brien C. A canine thermal model for simulating temperature responses of military working dogs. J Therm Biol. 2020;91:102651. 10.1016/j.jtherbio.2020.102651 [DOI] [PubMed] [Google Scholar]
- 32. Potter AW, Gonzalez JA, Looney DP. Biophysical assessment of the US Army Improved Hot Weather Combat Uniform (IHWCU) and a comparison to the currently fielded Fire Resistant Army Combat Uniform (FRACU), US Army Research Institute of Environmental Medicine, Natick, MA, 01760, USA; Technical Report, T20-02, 2019 [Google Scholar]
- 33. Schlader ZJ, O'Leary MC, Sackett JR, Johnson BD. Face cooling reveals a relative inability to increase cardiac parasympathetic activation during passive heat stress. Exp Physiol. 2018;103:701–13. 10.1113/EP086865 [DOI] [PubMed] [Google Scholar]
- 34. Prince SE, Chen H, Tong H, et al. Assessing the effect of beard hair lengths on face masks used as personal protective equipment during the COVID-19 pandemic. J Expo Sci Environ Epidemiol. 2021;31:953–60. 10.1038/s41370-021-00337-1 [DOI] [PMC free article] [PubMed] [Google Scholar]
- 35. Randall VA. Androgens and hair growth. Dermatol Ther. 2008;21:314–28. 10.1111/j.1529-8019.2008.00214.x [DOI] [PubMed] [Google Scholar]
- 36. Chieffi M. Effect of testosterone administration on the beard growth of elderly males. J Gerontol. 1949;4:200–4. 10.1093/geronj/4.3.200 [DOI] [PubMed] [Google Scholar]
- 37. Opstad PK. Androgenic hormones during prolonged physical stress, sleep, and energy deficiency. J Clin Endocrinol Metab. 1992;74:1176–83. 10.1210/jcem.74.5.1314847 [DOI] [PubMed] [Google Scholar]
- 38. Opstad P. Endocrine and metabolic changes during exhaustive multifactorial military stress. Results from studies during the ranger training course of the Norwegian Military Academy. In: The Effect of Prolonged Military Activities in Man Physiological and Biochemical Changes Possible Means of Rapid Recuperation;1995.
Associated Data
This section collects any data citations, data availability statements, or supplementary materials included in this article.
Data Availability Statement
All data are provided within the manuscript.



