Abstract
Aflatoxin B1 (AFB1) poses a severe threat to food safety due to its potent carcinogenicity. To address the need for rapid and on-site detection, this study developed a colorimetric biosensor based on an AFB1-responsive DNA aptamercross-linked sodium alginate hydrogel. Gold nanoparticles (AuNPs) were encapsulated within the hydrogel as a visual signal reporter. The sensing mechanism relies on target-induced dissociation of aptamer crosslinkers, leading to hydrogel disintegration and release of AuNPs. The hydrogel formulation was optimized regarding sodium alginate concentration and crosslinking conditions. To enhance sensitivity, an Exonuclease I (Exo I)-triggered target recycling strategy was implemented, which amplifies hydrogel network disruption by cleaving the aptamer–target complex and recycling the aptamer. The sensor demonstrated a linear detection range of 0–50 μM, with a detection limit of 12.9 nM, and exhibited high selectivity towards AFB1. This work presents a sensitive, visually readable, and portable platform for mycotoxin detection in food safety applications.
Keywords: Aflatoxin B1, Colorimetric detection, DNA-crosslinked hydrogel, Mycotoxin detection, Signal amplification
1. Introduction
A flatoxins are notorious mycotoxin contaminants in the global food supply. They are produced by the fungus Aspergillus flavus, and can be present at every stage of the food chain, from agricultural production and storage to final products such as animal feed, grains, peanuts, milk, and eggs, posing a severe threat to food safety [1,2]. Among them, aflatoxin B1 (AFB1) is the most hazardous, known for its potent carcinogenic and teratogenic effects [1,2]. Detection of aflatoxins in food is essential for ensuring food safety. Conventional methods, primarily based on high-performance liquid chromatography and mass spectrometry, offer high reliability and selectivity [3]. However, these techniques also have significant drawbacks, including high cost, lengthy detection times, and the inability to support real-time, onsite, or portable detection [3].
In recent years, aptamer-based biosensors have been developed and applied in mycotoxin detection [4]. A key component of these biosensors is DNA aptamer, a short single-stranded DNA (ssDNA) that can fold into secondary/tertiary structures upon binding to the target molecule [5–7]. This binding event can be converted into a measurable signal to enable target detection. Owing to their synthetic origin, DNA aptamers offer great modularity and are easy to produce compared to other biorecognition elements such as antibodies [8].
A recent development in biosensing involves the use of target-responsive hydrogels crosslinked by DNA aptamers [9,10]. Typically, polymers are grafted with ssDNAs which are partial complementary to the target-binding aptamer, to form modified polymer chains (PS-A and PS-B). The aptamers can hybridize with PS-A and PS-B to form a crosslinked network (hydrogel), providing both structural integrity and target specificity. Upon binding the target molecule, the aptamer crosslinkers dissociate, resulting in hydrogel disintegration and the consequent release of an encapsulated signaling agent [11]. Detection of the target is thus achieved by measuring this signal via readouts such as colorimetry, microfluidic chips, or common meters. Among these, colorimetric hydrogel sensors are particularly promising for on-site applications due to their visual readout and operational simplicity [3].
To enhance the sensitivity of the colorimetric hydrogel sensors, various signal amplification strategies have been employed, including rolling circle amplification (RCA), hybridization chain reaction (HCR), and the application of tool enzymes [12]. One such enzyme, Exonuclease I (Exo I) from E. coli, specifically degrades ssDNA from the 3′ to 5′ end, while leaving double-stranded DNA (dsDNA) largely intact. This property is exploited in a DNA-aptamer crosslinked hydrogel system [13–15]. In the initial state, the aptamer is hybridized to a complementary ssDNA grafted on a polymer chain, forming a dsDNA duplex that is resistant to Exo I. In the presence of the target, the target binds the aptamer, disrupting the crosslinked hydrogel structure, causing the aptamer to adopt a single-stranded conformation within the aptamer–target complex. When Exo I is present, it cleaves the exposed ssDNA aptamer in the aptamer–target complex, releasing the target back into the hydrogel. The liberated target can then bind to another intact aptamer crosslinker, initiating a new cycle of hydrogel displacement and cleavage. This recycling of the target amplifies the disruption of the hydrogel network and the release of the signal reporter, thereby improving detection sensitivity.
Therefore, this study developed an AFB1 aptamer-crosslinked hydrogel sensor for the visual and quantitative detection of AFB1 mycotoxin. An Exo I-triggered target recycling strategy was developed to enhance sensing sensitivity. The hydrogel matrix was fabricated from sodium alginate (SA), chosen for its good biocompatibility, abundance of functional groups, and ease of modification. Gold nanoparticles (AuNPs) were employed as the signal reporter, leveraging their unique localized surface plasmon resonance (LSPR) property, which results in strong absorption within the visible light spectrum, enabling convenient visual detection.
2. Materials and methods
2.1. Materials
NH2-mofidied DNA sequence (ssDNA-A:NH2-TTTTGTGGGCCTAGCGA, ssDNA-B:NH2-TTTACACGTGCCCAAC) and AFB1 aptamer (sequence: GTTGGGCACGTGTTGTCTCTCTGTGTCTCGTGCCCTTCGCTAGGCCCACA) [16] was purchased from Qingke Biotechnology Co., Ltd (Beijing, China). Aflatoxin B1 (AFB1), deoxynivalenol (DON), zearalenone (ZEN), and ochratoxin A (OTA) were purchased from Baiyidi Biotechnology Co., Ltd (Beijing, China). Sodium alginate (200 ± 20 mpa·s) and MES buffer (2-aminomethylsulfonic acid) were purchased from Beijing Inokai Technology Co., Ltd (Beijing, China). Trisodium citrate, HAuCl4·3H2O, 1-(3-dimethylamino propyl)-3-ethyl carbodiimide) (EDC) and N-hydroxysulfosuccinimide (Sulfo-NHS) were purchased from Beijing Mairuida Technology Co., Ltd (Beijing, China). Exonuclease I was purchased from the United States New England Biolabs Company (MA,USA).
2.2. Preparation of gold nanoparticles
Gold nanoparticles (AuNPs) were prepared according to a previously reported method [11]. Citric acid trihydrate solution (38.8 mM, 4 mL) and HAuCl4·3H2O solution (50 mM, 1 mL) were mixed, diluted using deionized water, and placed in a three-necked flask, followed by heating, reflux for 20 min, cooling to room temperature, and centrifuged at 10,000 rpm using a freezing centrifuge (High speed refrigerated centrifuge, H2-16 KR, Hunan Kecheng Instrument Equipment Co., Ltd,China) to obtain AuNPs.
2.3. Preparation of sodium alginate-based DNA crosslinked hydrogel
Solution of sodium alginate (0.25%–1.5% W/V% in MES buffer, pH = 6), ssDNA-A (100 μM in deionized water), ssDNA-B (200 μM in deionized water), and AFB1 aptamer (200–450 μM in deionized water) were prepared respectively. EDC and Sulfo NHS were added to sodium alginate solution in a ratio of 5:1 to 1:2, respectively. The reaction was conducted at room temperature for 30 min, followed by addition of ssDNA A (3 μL, 100 μM), ssDNA B (3 μL, 100 μM), AFB1 aptamer (1 μL, 350 μM), AuNPs (5 μL, 30 nM), EDC (2.61 μL, 5 mM), and Sulfo NHS (0.65 μL, 5 mM). The mixture was incubated at 37°C for 30 min to obtain the aptamer crosslinked hydrogel. In the sensing test, the amount of the hydrogel and solution containing AFB1 (2.5 μM) toxin was 50 μL and 80 μL, respectively. The absorbance at 530 nm of the experimental group (deionized water containing AFB1) and blank (deionized water without AFB1) was determined. The difference between the absorbance of the experimental group and that of the blank group (A sample-A blank,ΔA) was recorded.
2.4. Exo I-mediated signal amplification
Solution of sodium alginate (0.25%–1.5% W/V% in MES buffer, pH = 6), ssDNA-A (100 μM in deionized water), ssDNA-B (200 μM in deionized water), and AFB1 aptamer (200–450 μM in deionized water) were prepared respectively. EDC and Sulfo-NHS were added to sodium alginate solution in a ratio of 5:1 to 1:2, respectively. The reaction was conducted at room temperature for 30 min, followed by addition of ssDNA A (3 μL, 100 μM), ssDNA B (3 μL, 100 μM), AFB1 aptamer (1 μL, 350 μM), AuNPs (5 μL, 30 nM), EDC (2.61 μL, 5 mM), and Sulfo-NHS (0.65 μL, 5 mM). The mixture was incubated at 37°C for 30 min to obtain the aptamer crosslinked hydrogel. Then AFB1 toxin (2.5 μM, 80 μL) was added to the hydrogel (50 μL), followed by incubation at 37°C for a period of time. Then Exo I (1.5 μL) was added and incubated at 37°C for a period of time. The supernatant above the hydrogel was collected and its ΔA at 530 nm was measured using a multifunctional microplate detector (TECAN, Spark, Switzerland). Factors affecting the effect of the Exo I-mediated signal amplification, including Exo I loading and incubation time were investigated (Table 1). The absorbance at 530 nm of the experimental group (deionized water containing AFB1) and blank (deionized water without AFB1) was determined. The difference between the absorbance of the experimental group and that of the blank group (A sample-A blank,ΔA) was recorded.
Table 1.
Study on factors affecting effect of Exo I-mediated signal amplification.
| Sample | Exo I loading (μL) | Incubation time (X1: X2)a | AFB1 concentration (μM) |
|---|---|---|---|
| 1 | 1.5 | 0/0 | 2.5 |
| 2 | 1.5 | 30/0 | 2.5 |
| 3 | 1.5 | 25/5 | 2.5 |
| 4 | 1.5 | 25/10 | 2.5 |
| 5 | 1.5 | 25/15 | 2.5 |
| 6 | 1.5 | 15/15 | 2.5 |
| 7 | 1.5 | 30/- | 2.5 |
| 8 | 0.0 | 25/5 | 2.5 |
| 9 | 0.5 | 25/5 | 2.5 |
| 10 | 1.0 | 25/5 | 2.5 |
| 11 | 1.5 | 25/5 | 2.5 |
| 12 | 2.0 | 25/5 | 2.5 |
X1 represents the time (min) of AFB1 incubated with the hydrogel, X2 represents the time (min) of Exo I incubated with the hydrogel after addition of AFB1.
The group 30/- represents that the AFBI and Exo were introduced to the hydrogel together and incubated for 30 min in total.
2.5. Determination of linear detection range, limit of detection, and selectivity
AFB1 solution (80 μL, 0.15–50 μM) was added to the hydrogel sensor, incubated for 30 min, followed by measurement of the ΔA of the supernatant at 530 nm, using a multi-mode microplate reader (Tecan Group AG, Switzerland). LOD is calculated using a linear fitting curve, according to the equation below:
| (1) |
where σ is the standard deviation of the linear fitting curve (the standard deviation of the residuals), b is the slope of the curve.
The specificity of the sensor was determined by detecting mycotoxins similar to AFB1, including vomitoxin (DON), ochratoxin A (OTA), and zeaxanthin (ZEN).
2.6. Detection of mycotoxins in food samples
AFB1 was first added to 50 mL of peanut oil sample. Then the peanut oil containing AFB1 was tested using the aptamer-crosslinked hydrogel and the hydrogel with signal amplification based on the sensing method described in sections 2.4 and 2.5, respectively.
3. Results and discussion
3.1. Sensing mechanism
The sensor was constructed by first designing two single-stranded DNA sequences (ssDNA A and ssDNA B) to be partially complementary to the AFB1 aptamer. The aptamer then acted as a cross-linker, bridging between sodium alginate polymer chains grafted with ssDNA-A (PS-A) and ssDNA-B (PS–B) to form a hydrogel network (Fig. 1a). AuNPs were encapsulated within this matrix as the signaling agent. In the presence of the AFB1, its binding to the aptamer competes with the aptamerss-DNA hybridization. This competitive binding disrupts the crosslinks, leading to hydrogel dissociation and the subsequent release of AuNPs into the supernatant. The released AuNPs can then be quantified spectroscopically, enabling both visual and quantitative detection of AFB1.
Fig. 1.

(A) Schematic sensing mechanism of AFB1 aptamer-crosslinked sodium alginate hydrogel sensor, (b) hydrogel morphology, (c) absorbance of the supernatant containing AuNPs at 530 nm above the hydrogel in response to AFB1 (2.5 μM), (d) TEM image of AuNPs, (e) size distribution of AuNPs.
The hydrogel had a porous honeycomb or sponge-like microstructure with a continuous three-dimensional network (Fig. 1b). The presence of AFB1 dissociated the hydrogel, releasing the encapsulated AuNPS (Fig. 1d and e), resulting in an absorption at 530 nm (Fig. 1c). While in the absence of AFB1, the hydrogel was intact and no significant absorption at 530 nm was observed (Fig. 1c).
3.2. Sensor optimization
To optimize the sensing performance, factors affecting the structure of the hydrogel, including SA concentration and ratio of EDC: Sulfo-NHS, were investigated (Fig. 2). Overall, the hydrogels exhibited a highly porous structure (Fig. 2a). With increasing sodium alginate (SA) concentration, the hydrogel became denser and the pore size decreased. The release of AuNPs from the hydrogel in the presence of AFB1, represented by the ΔA intensity at 530 nm, showed minimal change as the SA concentration increased from 0.25 to 0.75 wt.%, but then decreased with further increase in SA concentration from 0.75 to 1.5 wt.% (Fig. 2b). The reduction is likely attributable to the denser structure and smaller pores of the hydrogel, which hindered the release of AuNPs. Considering both the hydrogel structure and the release of the signaling agent (AuNPs), an SA concentration of 0.75 wt.% was selected for hydrogel construction.
Fig. 2.

(A) Morphology of the hydrogel prepared with sodium alginate at different concentrations (0.25–1.5 wt.% in MES); (b) ΔA at 530 nm of the supernatant above the hydrogel sensor prepared with SA at different concentrations in the presence of AFB1 (10 μM); (c) ΔA at 530 nm of the supernatant above the hydrogel sensor prepared at different ratios of EDC: Sulfo-NHS in the presence of AFB1 (SA concentration of 0.75wt.%, AFB1 concentration of 10 μM).
To graft ssDNA onto the polymer chains of sodium alginate, 1-(3-dimethylaminopropyl)-3-ethylcarbodiimide (EDC) and Sulfo-NHS (N-hydroxysulfosuccinimide) were used to activate the sodium alginate. EDC activates the carboxyl groups on SA, which then react with Sulfo-NHS to form NHS esters, generating a more stable and reactive intermediate for coupling with primary amine groups on the ssDNA. The EDC: Sulfo-NHS ratio influences the SA-ssDNA grafting efficiency, the hydrogel structure, and consequently the sensing performance. Therefore, the effect of the EDC: Sulfo-NHS ratio on the sensing performance, specifically, the amount of AuNPs released from the hydrogel in the presence of AFB1, as indicated by the ΔA at 530 nm, was investigated (Fig. 2c). As the EDC: Sulfo-NHS ratio decreased, the ΔA intensity of the AuNPs at 530 nm initially increased, reached a maximum at ratios of 4:1 and 2:1, and then decreased. Based on these results, an EDC: Sulfo-NHS ratio of 2:1 was chosen for hydrogel fabrication. To summarize, optimal hydrogel formulation is SA concentration of 0.75 wt.% and EDC: Sulfo-NHS ratio of 2:1. This formulation was used for following study.
3.3. Signal amplification by Exo I-triggered target recycling
3.3.1. Signal amplification mechanism
Exo I specifically cleaves ssDNA from the ends and is insensitive to ssDNA. In the initial state, the aptamer is hybridized with a complementary ssDNA grafted onto the polymer chain, forming a dsDNA duplex that is resistant to Exo I cleavage. Upon introduction of the target (AFB1), the target binds the aptamer, disrupting the crosslinking and causing the aptamer to adopt a single-stranded conformation within the aptamer–target complex. This exposed ssDNA aptamer becomes susceptible to cleavage by Exo I. As a result, the target is released back into the hydrogel and can be reused to disrupt additional crosslinks (Fig. 3). This recycling of the target amplifies the dissociation of the hydrogel network and enhances detection sensitivity.
Fig. 3.

Scheme of signal amplification via target recycling using Exo I
3.3.2. Feasibility of signal amplification
The feasibility of signal amplification using Exo I was investigated (Fig. 4). In the absence of Exo I, the introduction of AFB1 induced hydrogel disintegration, releasing the encapsulated AuNPs, resulting in a ΔA of the supernatant at 530 nm. In the presence of Exo I, this ΔA intensity increased, indicating enhanced hydrogel breakdown and a more thorough release of AuNPs, attributable to the recycling of the AFB1 through Exo I-mediated cleavage of the AFB1-aptamer complex (Fig. 4a).
Fig. 4.

(A) ΔA at 530 nm of the supernatant above the hydrogel sensor with the addition of deionized water (control), AFB1, Exo I, or both of AFB1 and Exo I; (b) ΔA at 530 nm of the supernatant above the hydrogel sensor in the presence of AFB1 (2.5 μM) with or without Exo I (1.5 μL) incubated for different time (for the sample name X1/X2, X1 represents the time (min) of AFB1 incubated with the hydrogel, X2 represents the time (min) of Exo I incubated with the hydrogel after addition of AFB1. The group 30/- represents that the AFBI and Exo were introduced to the hydrogel together and incubated for 30 min in total. Refer to Table 1); (c) ΔA at 530 nm of the supernatant above the hydrogel sensor in the presence of AFB1 (2.5 μM) and Exo I at different loadings (incubated at 37°C for 30min).
Next, the effect of the AFB1 and Exo I incubation time on the hydrogel sensing performance was examined (Fig. 4b). When AFB1 and Exo I were added sequentially, i.e., AFB1 was introduced first and incubated for 25 min, followed by the addition of Exo I with further incubation for 5, 10, or 15 min (25/5, 25/10, 25/15), the ΔA at 530 nm increased with Exo I incubation time, reached a maximum at 10 min, and then decreased. Meanwhile, an absorption peak at 730 nm was observed, the intensity of which increased with longer Exo I incubation, this could be attributed to the aggregation of the AuNPs [17–19]. In contrast, in the presence of the AFB1 alone (30/0), no significant AuNP aggregation was detected. These results suggest that prolonged Exo I incubation induced AuNP aggregation, likely due to enzyme-induced disruption of the AuNP surface charge.
When the Exo I incubation time was fixed at 15 min, longer AFB1 incubation with the hydrogel (25 min vs 15 min) led to an increased ΔA at both 530 nm and 730 nm. Furthermore, when AFB1 and Exo I were introduced simultaneously (30/-) and co-incubated for a total of 30 min, a much stronger absorption at 730 nm than at 530 nm was observed, indicating severe AuNP aggregation. Since the ΔA at 530 nm reflects the sensing performance of the hydrogel, a high ratio of A530/A730 indicating minimal Exo I-induced AuNP aggregation is desirable. Therefore, an AFB1 incubation time of 25 min followed by Exo I incubation for 5 min was selected.
Next, the effect of Exo I loading on the sensing performance was investigated (Fig. 4c). The ΔA of the supernatant at 530 nm in the presence of AFB1 increased as the Exo I loading was raised from 0 to 1.5 μL, which can be attributed to the more extensive hydrogel disintegration at higher enzyme loadings. Considering both the signal amplification effect and cost, an Exo I loading of 1.5 μL was selected for subsequent experiments.
3.3.3. Sensing performance
We then determined the linear detection range and detection limit of the hydrogel sensor (Fig. 5). For the hydrogel sensor without signal amplification (Fig. 5a and b), the absorption of the supernatant at 530 nm increased with increasing AFB1 concentration with a linear relationship in the range of 0–100 μM, which is a wider detection range and compared to previously reported hydrogel sensors [20–23]. We then established a linear equation with the ΔA intensity (A) as the y-axis and AFB1 concentration as the x-axis:
Fig. 5.

(A) Dose–response curve of the hydrogel sensor without signal amplification toward AFB1 with increasing AFB1 concentration; (b) selectivity of AFB1 of the hydrogel sensor without signal amplification; (c) Dose–response curve of the hydrogel sensor with signal amplification toward AFB1 with increasing AFB1 concentration; (d) selectivity of AFB1 of the hydrogel sensor with signal amplification.
| (2) |
where Y is the ΔA intensity (A) of the supernatant at 530 nm in the presence of AFB1, X is AFB1 concentration, μM. The hydrogel sensor had a limit of detection (LOD) of 0.18 μM.
Similarly, for the hydrogel sensor with Exo I-assisted signal amplification (Fig. 5c, d), a linear equation with the ΔA intensity (ΔA) as the y-axis and AFB1 concentration as the x-axis was established:
| (3) |
where Y is the ΔA intensity (ΔA) of the supernatant at 530 nm in presence of AFB1, X is AFB1 concentration, μM. The hydrogel sensor had a linear detection range of 0–0.1 μM and a LOD of 12.9 nM. The Exo I-triggered target recycling strategy significantly improved the sensing sensitivity of the hydrogel sensor. In the presence of EXO I, the detection limit improved from 0.18 μM to 12.9 nM, representing an approximately 14-fold increase in the sensitivity.
We next tested the specificity of the two hydrogel sensors by detecting mycotoxins with chemical core-skeleton structures like AFB1, including zearalenone (ZEN), ochratoxin A (OTA) and deoxynivalenol (DON). The sensors both had a high ΔA at 530 nm in the presence of AFB1 and negligible ΔA with other mycotoxins, suggesting their high selectivity (Fig. 5b–d).
3.3.4. Food sample testing
The feasibility of the sensor in detecting AFB1 in food matrix (peanut oil) was evaluated (Table 2, Table 3). For the non-signal-amplification mode, the recovery rates ranged from 102% to 120%, with relative standard deviations (RSDs) below 2.44% (Table 2). For the signal-amplification mode, the recovery rates ranged from 117% to 137%, with RSDs below 2.63% (Table 3). These results demonstrate that the sensor exhibits good accuracy for AFB1 detection in real food matrices.
Table 2.
Detection of AFB1 in food samples using the hydrogel sensor without signal amplification.
| Sample | Target | Target added (μM) | Target detecteda (μM) | Recovery rate (%) | RSD (%, n = 3) |
|---|---|---|---|---|---|
| Peanut oil | AFB1 | 0.2 | 0.24 ± 0.006 | 118.33 ± 2.89 | 2.44 |
| Peanut oil | AFB1 | 15 | 15.67 ± 0.28 | 104.33 ± 2.08 | 1.99 |
Values are presented as Mean I SD (n = 3).
Relative standard deviation (RSD) is shown in the last column.
Table 3.
Detection of AFB1 in food samples using the hydrogel sensor with signal amplification.
| Sample | Target | Target added (μM) | Target detecteda (μM) | Recovery rate (%) | RSD (%, n = 3) |
|---|---|---|---|---|---|
| Peanut oil | AFB1 | 0.01 | 0.012 ± 0.0002 | 118.67 ± 2.08 | 1.75 |
| Peanut oil | AFB1 | 0.1 | 0.13 ± 0.004 | 133.33 ± 3.51 | 2.63 |
Values are presented as Mean I SD (n = 3).
Relative standard deviation (RSD) is shown in the last column.
4. Conclusion
This study developed a sensitive and selective colorimetric biosensor for AFB1 detection based on a DNA aptamer-crosslinked sodium alginate hydrogel. The sensor utilizes an AFB1-specific aptamer as a crosslinker. Upon the aptamer binding the AFB1, the hydrogel network disintegrates, releasing pre-loaded AuNPs for visual and quantitative analysis. An Exo I-mediated target recycling strategy was incorporated, which cleaves the liberated aptamer-AFB1 complex, recycling the target to amplify signal generation and significantly enhance sensitivity. After optimization of the hydrogel composition, the sensor demonstrated a wide linear detection range and good specificity against other common mycotoxins (DON, OTA, ZEN). This work presents a promising, visually readable platform offering a potential for application in rapid, on-site food safety screening. Future efforts will focus on testing in real samples and further device integration.
Acknowledgement
This work was supported by the Beijing Natural Science Foundation (No. L255013, L2605004) and National Natural Science Foundation of China (No. 22208006).
Funding Statement
This work was supported by the Beijing Natural Science Foundation (No. L255013, L2605004) and National Natural Science Foundation of China (No. 22208006)
References
- 1. Wang F, Han Y, Wang S, Ye Z, Wei L, Xiao L. Single-particle LRET aptasensor for the sensitive detection of aflatoxin B1 with upconversion nanoparticles. Anal Chem. 2019;91(18):11856–63. doi: 10.1021/acs.analchem.9b02599. [DOI] [PubMed] [Google Scholar]
- 2. Zhao M, Wang P, Guo Y, Wang L, Luo F, Qiu B, et al. Detection of aflatoxin B1 in food samples based on targetresponsive aptamer-cross-linked hydrogel using a handheld pH meter as readout. Talanta. 2018;176:34–9. doi: 10.1016/j.talanta.2017.08.006. [DOI] [PubMed] [Google Scholar]
- 3. Kant T, Shrivas K, Tejwani A, Tandey K, Sharma A, Gupta S. Progress in the design of portable colorimetric chemical sensing devices. Nanoscale. 2023;15(47):19016–38. doi: 10.1039/d3nr03803c. [DOI] [PubMed] [Google Scholar]
- 4. Song S, Wang L, Li J, Fan C, Zhao J. Aptamer-based biosensors. TrAC, Trends Anal Chem. 2008;27(2):108–17. [Google Scholar]
- 5. Ilgu M, Nilsen-Hamilton M. Aptamers in analytics. Analyst. 2016;141(5):1551–68. doi: 10.1039/c5an01824b. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 6. Kim J, Chang H, Yeun J, Baek J, Im SG. Enhanced glioblastoma- targeted aptamer discovery by 3D Cell-SELEX with hyaluronic acid hydrogel. ACS Biomater Sci Eng. 2025;11(8):4806–17. doi: 10.1021/acsbiomaterials.5c00504. [DOI] [PubMed] [Google Scholar]
- 7. Singh NK, Wang YX, Wen CN, Davis B, Wang XL, Lee K, et al. High-affinity one-step aptamer selection using a nonfouling porous hydrogel. Nat Biotechnol. 2024;42(8) doi: 10.1038/s41587-023-01973-8. [DOI] [PubMed] [Google Scholar]
- 8. Crivianu-Gaita V, Thompson M. Aptamers, antibody scFv, and antibody fab’ fragments: an overview and comparison of three of the Most versatile biosensor biorecognition elements. Biosens Bioelectron. 2016;85:32–45. doi: 10.1016/j.bios.2016.04.091. [DOI] [PubMed] [Google Scholar]
- 9. Zhang YS, Khademhosseini A. Advances in engineering hydrogels. Science. 2017;356(6337):eaaf3627.. doi: 10.1126/science.aaf3627. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 10. Zhang HQ, Hu HT, Li Y, Wang JZ, Ma L. A ferrocene-based hydrogel as flexible electrochemical biosensor for oxidative stress detection and antioxidation treatment. Biosens Bioelectron. 2024:248. doi: 10.1016/j.bios.2023.115997. [DOI] [PubMed] [Google Scholar]
- 11. Sangwan S, Seth R. Synthesis, characterization and stability of gold nanoparticles (AuNPs) in different buffer systems. J Cluster Sci. 2022;33(2):749–64. [Google Scholar]
- 12. Zhang CY, Chen J, Sun R, Huang ZJ, Luo ZW, Zhou C, et al. The recent development of hybridization chain reaction strategies in biosensors. ACS Sens. 2020;5(10):2977–3000. doi: 10.1021/acssensors.0c01453. [DOI] [PubMed] [Google Scholar]
- 13. Ma HK, Wang P, Xie YY, Liu JH, Feng W, Li SQ. Ratiometric electrochemical aptasensor for the sensitive detection of carcinoembryonic antigen based on a hairpin DNA probe and exonuclease I-assisted target recycling. Anal Biochem. 2022:649. doi: 10.1016/j.ab.2022.114694. [DOI] [PubMed] [Google Scholar]
- 14.Su RF, Li ZH, Yang CY, Li Y, Wang JY, Sun CY. Spectrochim Acta Part A-molecular and Biomolecular Spectroscopy. 2024. Fluorescent aptasensors for sensitive detection of lead ions based on structure-switching DNA beacon probe and exonuclease I-mediated signal amplification; p. 320. [DOI] [PubMed] [Google Scholar]
- 15. Zhang Y, Wu CY, Liu HX, Khan MR, Zhao ZF, He GP, et al. Label-free DNAzyme assays for dually amplified and one-pot detection of lead pollution. J Hazard Mater. 2021:406. doi: 10.1016/j.jhazmat.2020.124790. [DOI] [PubMed] [Google Scholar]
- 16. Sabet FS, Hosseini M, Khabbaz H, Dadmehr M, Ganjali MR. FRET-Based aptamer biosensor for selective and sensitive detection of aflatoxin B1 in peanut and rice. Food Chem. 2017;220:527–32. doi: 10.1016/j.foodchem.2016.10.004. [DOI] [PubMed] [Google Scholar]
- 17. Zhang ZQ, Wu YH. Investigation of the NaBH4-Induced Aggregation of Au Nanoparticles. Langmuir. 2010;26(12):9214–23. doi: 10.1021/la904410f. [DOI] [PubMed] [Google Scholar]
- 18. Chen XY, Ma RT, Ha W, Shi YP. Direct colorimetric detection of aspartic acid in rat brain based on oriented aggregation of janus gold nanoparticle. Sensors and Actuators Bchemical. 2018;274:668–75. [Google Scholar]
- 19. Li M, Johnson S, Guo HT, Dujardin E, Mann S. A generalized mechanism for ligand-induced dipolar assembly of plasmonic gold nanoparticle chain networks. Adv Funct Mater. 2011;21(5):851–9. [Google Scholar]
- 20. Li YY, Meng SY, Dong N, Wei Y, Wang Y, Li X, et al. Space-confined electrochemical aptasensing with conductive hydrogels for enhanced applicability to aflatoxin B1 detection. J Agric Food Chem. 2023;71(40):14806–13. doi: 10.1021/acs.jafc.3c04744. [DOI] [PubMed] [Google Scholar]
- 21. Tang LY, Huang YY, Lin CY, Qiu B, Guo LH, Luo F, et al. Highly sensitive and selective aflatoxin B1 biosensor based on exonuclease I-catalyzed target recycling amplification and targeted response aptamer-crosslinked hydrogel using electronic balances as a readout. Talanta. 2020:214. doi: 10.1016/j.talanta.2020.120862. [DOI] [PubMed] [Google Scholar]
- 22. Li WT, Shi YQ, Zhang XA, Hu XT, Huang XW, Liang NN, et al. A DNA tetrahedral scaffolds-based electrochemical biosensor for simultaneous detection of AFB1 and OTA. Food Chem. 2024:442. doi: 10.1016/j.foodchem.2023.138312. [DOI] [PubMed] [Google Scholar]
- 23. Camizci Aran G, Bayraç C. Simultaneous dual-sensing platform based on aptamer-functionalized DNA hydrogels for visual and fluorescence detection of chloramphenicol and aflatoxin M1. Bioconjug Chem. 2023;34(5):922–33. doi: 10.1021/acs.bioconjchem.3c00130. [DOI] [PubMed] [Google Scholar]
