Table 2.

Sensors 1 and 2 were positioned at the tip of the wire. Sensor 3 was positioned at the midway point of the wire. Sensor 4 was used as control and positioned next to the inner side of the phantom midway through the body of the ASTM phantom, while sensor 5 (also a control) was positioned at the inner side of the phantom midway through the head of the ASTM phantom (see Figure 2B).

	Sensor 1 (wire tip)			Sensor 2 (wire tip)			Sensor 3 (wire center)			Sensor 4 (control in body)			Sensor 5 (control in head)
Pos	Begin	End	Diff	Begin	End	Diff	Begin	End	Diff	Begin	End	Diff	Begin	End	Diff
Tx/Rx BODY COIL
01	17.8	26.1	8.3	18.3	26.9	8.6	18.2	19.0	0.8	18.1	18.1	0.0	18.5	19.2	0.7
02	16.9	21.3	4.4	17.4	21.7	4.3	18.3	19.0	0.7	18.1	18.1	0.0	19.1	19.8	0.7
03*	17.0	16.9	−0.1	17.4	17.3	−0.1	17.8	17.7	−0.1	18.1	18.1	0.0	19.7	19.9	0.2
04	17.6	18.8	1.2	18.1	19.3	1.2	18.5	18.8	0.3	18.2	18.2	0.0	19.8	20.5	0.7
05	18.2	20.0	1.8	18.7	20.5	1.8	18.6	18.9	0.3	18.2	18.2	0.0	20.4	21.0	0.6
06	17.2	18.6	1.4	17.5	18.7	1.3	18.9	19.3	0.4	18.4	18.4	0.0	20.9	21.4	0.5
07	17.0	17.8	0.8	17.5	18.3	0.8	18.0	18.1	0.1	18.3	18.4	0.1	21.3	22.0	0.7
08	18.6	20.4	1.8	19.0	20.6	1.6	18.6	19.0	0.4	18.7	18.6	−0.1	19.6	20.3	0.7
09	18.5	19.2	0.7	18.9	19.5	0.6	18.6	18.7	0.1	18.5	18.5	0.0	20.2	20.8	0.6
10	18.5	19.0	0.5	18.9	19.3	0.4	18.3	18.4	0.1	18.4	18.4	0.0	20.7	21.3	0.6
11	19.7	19.6	−0.1	20.1	20.0	−0.1	19.2	19.3	0.1	18.4	18.4	0.0	21.4	21.9	0.5
Tx/Rx HEAD COIL
01	21.1	23.2	2.1	21.3	25.3	4.0	21.1	22.0	0.8	18.3	18.3	0.0	22.0	22.3	0.3
04	19.3	19.2	−0.1	19.6	19.5	−0.1	18.9	18.8	−0.1	18.4	18.3	−0.1	21.7	22.2	0.5
REPEATED EXPERIMENTS WITH Tx/Rx BODY COIL FOR QUALITY ASSURANCE
01	21.4	25.8	4.4	21.6	30.4	8.8	21.8	23.3	0.5	18.3	18.3	0.0	22.0	22.5	0.5
08	19.2	20.9	1.7	19.6	20.9	1.3	18.9	19.2	0.3	18.3	18.3	0.0	20.8	21.4	0.6

^*For the 3rd position the experiment was stopped after a few minutes because no significant heating was observed.