Skip to main content
Proceedings of the National Academy of Sciences of the United States of America logoLink to Proceedings of the National Academy of Sciences of the United States of America
. 2021 Aug 13;118(33):e2105422118. doi: 10.1073/pnas.2105422118

Emergent electromagnetic induction beyond room temperature

Aki Kitaori a,1, Naoya Kanazawa a,1, Tomoyuki Yokouchi b, Fumitaka Kagawa a,c, Naoto Nagaosa a,c,1, Yoshinori Tokura a,c,d,1
PMCID: PMC8379948  PMID: 34389677

Significance

Emergent inductors that utilize emergent electric fields generated by the current-induced motion of spiral spin textures have the potential to realize dramatic miniaturization of inductance elements. By using YMn6Sn6, which has been attracting attention as a kagome lattice magnetic material in recent years, we have realized the room-temperature operation of emergent inductors. This micron-scale emergent inductor device shows not only an inductance as large as a commercially available product but also a sign change of inductance, which is a previously undescribed phenomenon.

Keywords: emergent inductor, spiral magnet, room temperature

Abstract

Emergent electromagnetic induction based on electrodynamics of noncollinear spin states may enable dramatic miniaturization of inductor elements widely used in electric circuits, yet the research is still in its infancy and many issues must be resolved toward its application. One such problem is how to increase working temperature to room temperature, and possible thermal agitation effects on the quantum process of the emergent induction are unknown. We report here large emergent electromagnetic induction achieved around and above room temperature, making use of a few tens of micrometer-sized devices based on the high-temperature (up to 330 K) and short-period (≤ 3 nm) spin-spiral states of a metallic helimagnet. The observed inductance value L and its sign are observed to vary to a large extent, depending not only on the spin-helix structure controlled by temperature and applied magnetic field but also on the applied current density. The present finding on room-temperature operation and possible sign control of L may provide a step toward realizing microscale quantum inductors on the basis of emergent electromagnetism in spin-helix states.


Conventional inductors based on classical electromagnetism are one of the most important elements in electric circuits, as characterized by the relation V = L dI/dt, where V, I, and L are voltage, current, and inductance, respectively. Since L of the inductor coil is proportional to the product of the square of the coil’s winding number and the coil’s cross-section, it is difficult to reduce the dimensions of the inductor while keeping L large enough. To overcome the size problem of the coil-shaped inductor, the simple scheme of the electromagnetic induction has recently been proposed to use the current-induced spin dynamics in a helical-spin system (1) and experimentally verified for the helimagnetic phases of a metallic compound (2). The idea is to utilize the time-dependent emergent electromagnetic field or dynamics of the Berry phase (3, 4) produced by the conduction electrons flowing on the helical spin texture (1).

The emergent magnetic field (b) acting on conduction electrons is realized in a noncoplanar spin texture endowed with scalar spin chirality, typically in the skyrmion-lattice phase (5, 6). For example, the current-driven motion of skyrmions accompanying b produces the emergent electric field (e), which is known to give a current-dependent correction to the topological Hall effect in the skyrmion-lattice phase (7). The generalized Faraday’s law (8) states that ∇×e=−∂b/∂t or e=−∂a/∂t, where a is the Berry connection satisfying that b=∇×a. Thus, to generate the emergent electric field on the spin helix, the originally static b is not necessarily required but only the time-dependent deformation of the spin helix by alternating electric current (ac) is sufficient. In consideration of spin transfer torque on spin helix in the continuum limit, the coordinate component of emergent electric field (ei) is described as (4, 5, 8)

ei=h2πen⋅(∂in×∂tn), [1]

where n, h, and e are a unit vector parallel to the direction of spins, Planck’s constant, and bare electron charge, respectively. As opposed to b, e is related to the dynamics of spin structures and proportional to the solid angle dynamically swept by n(t). Hence, the motion of noncollinear spin structures can induce ei (9–14). For example, in the case of a proper-screw (Bloch-wall-like) helix (Fig. 1A), the emergent electric field can be described as (1)

ex=Pheλ∂tϕ,  [2]

where λ is the period of helix, P is a spin polarization factor, ϕ is the tilting angle of the spin from the spiral plane, and the x axis is taken parallel to the magnetic modulation vector (q). We note that ex can be generated regardless of the direction of the helical plane, e.g., also in cycloidal-type (Néel-wall-like) spin modulations. Also, the sign of ex is independent of spin helicity, which allows the emergent induction even in a multidomain state with different helical structures. This is a striking difference from structural chirality-driven phenomena such as chiral-induced spin selectivity (15–17) and nonreciprocal transport (18) in chiral systems.

Fig. 1.

Fig. 1.

Conceptual diagram of emergent induction in spin-helix and helimagnetic orders in YMn6Sn6. (A) Schematic illustration of emergent electromagnetic induction produced in the spin-helix state. Spin configurations of a proper-screw helix in real space (Top) and its projection into the unit sphere under the current-driven motion at several elapsed-time points (Bottom). (B and C) Oblique (B) and top (C) views of crystal structure of YMn6Sn6, built up from Y layers with triangular lattices, Mn layers with kagome lattices, and Sn layers with honeycomb lattices. Schematic illustrations are drawn by using VESTA (34) (D–G) Schematic illustrations of proper-screw helical (D), transverse conical (E), fan-like (F), and forced ferromagnetic (G) structures. (H) YMn6Sn6 magnetic phase diagram for H || a-axis. The blue, yellow, green, and red regions represent proper-screw helical (H), transverse conical (TC), fan-like (FL), and forced ferromagnetic (FF) phases, respectively. (Inset) A scanning electron microscope image of a YMn6Sn6 thin plate device.

The appearance of the emergent electromagnetic inductance was recently confirmed for the helimagnet Gd3Ru4Al12 (2), in which various noncollinear spin structures, such as proper-screw and transverse conical (see Fig. 1 D and E), show up below 20 K with a short helical pitch of λ ∼ 2.8 nm due to the magnetic frustration effect of the localized Gd moments coupled via a Ruderman–Kittel–Kasuya–Yosida interaction (19–23). Several important features of the emergent inductor were experimentally confirmed or clarified by this first experimental demonstration (2): 1) the inversed size scaling law, as anticipated, that L for the emergent inductor increases with the reduction of the element cross-section S, 2) the mostly negative sign of the emergent inductance L in contrast to the positive value for conventional classic inductors, 3) the highly nonlinear behavior of the emergent inductance L with the current density, and 4) the frequency dependence of the emergent inductance showing the Debye-type relaxation feature. Whether these features of the emergent electromagnetic inductance are generic and common to all the possible spin-helix states, in particular to the room-temperature helix states, is an important subject to be verified by experiments, in addition to the possible further enhancement of the inductance value at higher temperatures.

Results and Discussion

Magnetic Phases and Emergent Inductance.

The main purpose of the present study is to realize the large-enough magnitude, e.g., exceeding microhenry level, of the emergent electromagnetic inductance in the micrometer-sized device around and above room temperature; this would be a primarily step toward the application of the emergent electric field to the actual electronic devices. As the natural extension of the related study (2), we sought a high-temperature helimagnetic state with nanometer-scale spin-helical pitch in metallic compounds. Among several candidate materials, we target here the helimagnet YMn6Sn6, where strong exchange interactions between 3d-moments on Mn kagome lattices (Fig. 1B) and strong Hund’s-rule-like couplings to itinerant electrons are expected. The compound indeed undergoes the helimagnetic transition approximately below a temperature as high as 330 K (Fig. 1H) (24–28), showing the short-period helimagnetic states (28–30) such as proper-screw helix (H, Fig. 1D) and transverse conical state (TC, Fig. 1E), whose magnetic modulation vectors q run parallel to the c-axis, i.e., normal to the Mn kagome-lattice plane. As increasing the magnetic field applied parallel to the a-axis, i.e., normal to the q direction or c-axis, the H state turns into TC, and (at low temperatures through the fan-like state [FL, Fig. 1F]) finally to the forced ferromagnetic state (FF, Fig. 1G), as shown in the phase diagram in the temperature vs. magnetic-field plane (Fig. 1H). Here, the phase diagram was obtained by the magneto-transport measurements on the actual micrometer-scale device (see Fig. 1H, Inset) with referring to the results reported for the bulk crystal and the magnetic-phase assignments done in previous reports (29); the phase transition temperatures and critical magnetic fields show a good agreement between the micrometer-sized device and the bulk crystal of YMn6Sn6 (see SI Appendix, Fig. S2).

The complex helical magnetic structures, in particular for the H and TC phases, appearing in this compound at relatively low magnetic fields and relatively high temperatures should be mentioned. As partly elucidated by recent neutron scattering studies (29–31), there may be coexisting plural q-modulations in the H and TC phase. The q-values (corresponding to λ values less than 2.6 nm) appear to be plural, such as two- or threefold; for example, there appear coexistent multiple magnetic Bragg satellites from incommensurate q-states, and the relative weight of the respective q-states appears to change depending on each phase, temperature, or magnetic field (29–31). Such a complex feature and variation of the spin-helix modulation may influence the variation of the emergent inductance magnitude or even its sign, yet the elaborate arguments may have to await a future study to fully clarify the detailed spin structures. Nonetheless, the very short helical pitches (large q values) are obviously favorable for the generation of high inductance value, as argued in Eq. 2. Below, we examine the characteristics of the emergent electromagnetic inductance for the micrometer-scale devices made of YMn6Sn6 on which the electric current is applied along the c-axis (i.e., parallel to the q vector) while changing temperature and magnetic field applied along the a-axis (normal to the c-axis), as shown in Fig. 1H, Inset.

Fig. 2A exemplifies the imaginary part of ac resistivity (ρ1f) at 270 K measured using the ac input current density j=j0⁡sin(2πft) (j0=2.5×104A/cm2 and f = 500 Hz); the device (#1) size are 4.8 μm × 9.3 μm in cross-section (S) and 25.0 μm in voltage-terminal distance (d). We also confirmed reproducibility (see SI Appendix, Fig. S1). The real part of inductance value L can be directly related to Imρ1f via the relation

L=Imρ1fd/2πfS [3]

and plotted on the right ordinate scale for the present device. The absolute value of L is nearly constant with magnetic field within the low-field H phase and increases in the TC phase, exceeding a value as large as 2 μH (microhenry). In further increasing the magnetic field above 4 T, the absolute value of L steeply decreases within the TC phase, and around the TC-to-FF transition it changes sign and shows a positive peak. As anticipated from the spin-helix origin of the emergent electric field generation, the L almost disappears when deeply entering the FF phase.

Fig. 2.

Fig. 2.

Emergent inductance beyond room temperature and its temperature and magnetic-field dependence in YMn6Sn6. (A–I) Magnetic-field (H) dependence of the imaginary part of the complex resistance Imρ1f measured under H || a-axis and an ac input current density j=j0⁡sin(2πft) (j0=2.5×104 A/cm2, f = 500 Hz, j || c-axis) at various temperatures. The blue, yellow, green, and red shadows represent proper-screw helical (H), transverse conical (TC), fan-like (FL), and forced ferromagnetic (FF) phases, respectively. (J–M) H dependence of the imaginary part of the complex resistance ΔImρ1f at selected temperatures for low current excitation, j0=4.4×103 A/cm2, which was corrected by subtraction of the contribution from parasiteic capacitance. (N) Color contour mapping of Imρ1f at j0=2.5×104 A/cm2 in the T–H plane. Phase boundaries are indicated by black dots and dashed lines.

On the same device structure (#1) under the same current excitation condition (j0=2.5×104A/cm2), the temperature dependence of Imρ1f(H) curve is shown in Fig. 2 B–I together with the assignments of the magnetic phases (colored vertical bands). The variation of Imρ1f at j0=2.5×104A/cm2 is also displayed in Fig. 2N as a color contour map on the plane of temperature (T) and magnetic field (H). With lowering T, typically below100 K, the absolute value of Imρ1f is rapidly suppressed, perhaps due to the increase of the ab-plane magnetic anisotropy which tends to suppress the current-induced spin deformation (amplitude in ϕ or ∂tϕ term in Eq. 2). In the temperature region below 270 K, the Imρ1f takes mostly negative values in the H, TC, and FL phases, while the magnitude is different in the respective phases and also depends on temperature. Notably, around the boundary between helimagnetic TC (or FL) and FF phases, the Imρ1f once increases to take the positive-value peak (see the red-colored region in Fig. 2N). The positive value of Imρ1f or L is more clearly and broadly observed at higher temperatures above 300 K. For example, at 300 K the Imρ1f is still negative within the H phase but shows a positive value in the whole TC phase, accompanying a sharp negative dip upon the field-induced H-to-TC transition. Surprisingly, even above the magnetic transition temperature (330 K), e.g., at 350 K, the broad positive peak is observed in low-field region, followed by the negative background in higher-field (>3 T) region. As for the lower current-density (j0=4.4×103A/cm2) behavior of Imρ1f as shown in Fig. 2 J–M see the discussion in the next section.

Frequency Dependence and Current Nonlinearity.

Next, we proceed to the frequency dependence and the current nonlinearity for the present emergent inductor. To investigate a wide range of frequency dependence, we performed the LCR-meter measurement on the two-terminal device (#2 with 5.5 μm×1.8 μm in S and 28.8 μm in d; see SI Appendix, Fig. S1) at zero field. Fig. 3, Inset exemplifies the frequency (f) dependence of the real and imaginary parts of the inductance L at 100 K. A prototypical Debye-type relaxation behavior is observed there with the characteristic frequency (f0) around 1 kHz, at which ImL shows a peak (2, 31) (see Materials and Methods for the definition of Im L). The similar relaxation-type f dependence of Re L is observed at various temperatures, as shown in the main panel of Fig. 3. The characteristic frequency f0 ∼ 1 kHz is rather insensitive to the temperature variation, while the L value changes from negative to positive in approaching the magnetic transition temperature (TN ∼ 330 K). This means that the deformation of spins cannot fully follow alternating currents with a frequency above 1 kHz, which is ascribed to the extrinsic pinning effect stemming from defects/impurities. As compared with the case of the low-TN (∼20 K) helimagnet Gd3Ru4Al12 where f0 ∼ 10 kHz and λ ∼ 2.8 nm (2), one order of magnitude lower f0 in the present compound with comparable λ may be ascribed to the smaller extrinsic pinning effect. Such frequency dependence of the L would be improved to show higher f0 by enhancing the extrinsic pinning effect via, for example, artificially introducing the pinning sites.

Fig. 3.

Fig. 3.

Frequency dependence of the real part of complex inductance measured with the LCR meter at zero magnetic field. The dashed lines are fitting curves assuming Debye-type relaxation. (Inset) A prototypical Debye-type relaxation behavior of complex inductance observed at 100 K.

As for the current-nonlinear behavior of L, this compound shows dramatic but complex magnetic-field-dependent features. At first, we show the very low current density regime of the H-dependent inductance in this compound at various temperatures in Fig. 2 J–M. The Imρ1f or L is always positive in the linear response regime, i.e., low current density j0=4.4×103A/cm2 while turning into mostly negative as j increases to j0=2.5×104A/cm2 in the helimagnetic phases H and TC ; see and compare Fig. 2 B–I and J–M for j0=2.5×104A/cm2 and j0=4.4×103A/cm2 (low current density), respectively. When the current density j is further increased, the magnetic-field variation of the inductance or Imρ1f is observed to change in a qualitative manner, even including its sign. Shown in Fig. 4A is the typical result at 270 K on device #3 (3.8 μm×8.5 μm in S and 35.5 μm in d; see SI Appendix, Fig. S1); the magnetic-field dependence at the current density j0 ∼2×104A/cm2 therein nearly reproduces the results of device #1 shown in Fig. 2A at j0=2.5×104A/cm2. In all the helimagnetic phases multiple sign changes of Imρ1f occur upon the development of nonlinearity. To see this more clearly, we plot the evolution of Imρ1f with the current density as monitored at 0 T (H phase), 2.5 T (lower-field side of TC phase), and 4.2 T (higher-field side of TC phase) in Fig. 4B together with the negative-maximal and positive-maximal magnitudes in this magnetic field range eye-guided by the envelope curves. Although the magnitude of Imρ1f and the frequency at the sign change of Imρ1f are different with the magnetic states, the overall profile of its j dependence is generic. Positive Imρ1f appears and generally shows a moderate increase in the low-j region below 2×104A/cm2. With increasing j, Imρ1f sharply decreases in combination with a sign reversal then subsequently exhibits accelerated rise with another sign change (see SI Appendix, Fig. S3). One possible interpretation of this nontrivial j dependence is that the positive inductance linear in j is buried in the nonlinear component pronounced in the high-j region. Indeed, a recent theoretical study provides a consistent argument (32, 33). The complex conductivity σ(ω) comprises multiple components with each distinct response to j due to rich dynamical characteristics of the spin helix. While the dominant term is the Drude conductivity σd of the metallic electrons, the contributions associated with the collective modes of spin spirals σc(ω) are a source of emergent inductance. The inductance of Imρ is therefore approximated as −Imσc(ω)σd2, which is subdivided into two contributions, one from the tilt ϕ and the other from the phason, both of which constitute the canonical conjugate pair. The former is equivalent to the emergent electric field giving the positive inductance, while the latter depends sensitively on the impurity pinning of the phason. We now understand that the phason contribution is the major origin of the nonlinearity and sign change of the inductance, since the pinning frequency depends on the temperature and current density, and also the depinning beyond the threshold current density gives even more dramatic change in the phason dynamics. Nevertheless, other mechanisms may be also relevant to the nonlinearity. For example, the current-induced change of the magnetic structure itself, such as the weight change of the plural q-value components even within the TC phase region, should be taken into account for the highly j-nonlinear. This is to be confirmed by the in situ neutron or magnetic resonant X-ray scattering studies while changing the magnetic field and electric current density. In turn, the possible control of the emergent inductance sign and magnitude in terms of the current excitation would be an important function for this class of quantum inductor.

Fig. 4.

Fig. 4.

Nonlinear emergent inductance with several current densities at 270 K. (A) Magnetic field (H) dependence of the imaginary part of complex resistance Imρ1f measured under H // a-axis and different amplitudes of ac density j=j0⁡sin(2πft) (f = 500 Hz, j || c-axis). (B) Current density (j0) dependence of Imρ1f at specific H values. Red and blue dashed lines represent positive- and negative-maximal magnitudes of Imρ1f at each j0, respectively.

Conclusion

We have demonstrated the potential of the above-room-temperature quantum inductor as derived from the emergent electric field generated in the short-pitch (∼3 nm) helimagnetic states, such as proper-screw helix and transverse conical states, of the YMn6Sn6 crystal plate. The imaginary part of ac resistivity Imρ1f as the representation of the intrinsic material parameter for the electromagnetic induction can show large absolute values of approximately microohm centimeter level, ensuring the large inductance value for the micrometer-sized or thin-film device, in which the current density can be increased. The emergent inductance is highly nonlinear with the current density exceeding 104 A/cm2, mostly negative but turns into a large positive value near the phase boundary to the forced ferromagnetic region or with increasing the current density in the transverse conical spin state. Apart from the case of the low-current-density (<104 A/cm2) excitation region, the positive sign of the emergent inductance is likely due to the gapless nature of collective spin excitation. The strong nonlinear behavior of emergent inductance can also be related to the collective phason modes sensitively responding to the impurity pinning; however, the detailed mechanism remains to be clarified. The possibility of the varying magnitude and sign of the emergent inductance with current density may lead to a useful functionality of the quantum inductor as well as the advantage of several orders-of-magnitude miniaturization as compared with the classical coil inductor. Since the low Debye frequency (less than a few kilohertz) and hence the low Q-factor (2πfL/R ∼0.6%; also see SI Appendix, Fig. S2 for resistivity value) critically limit the performance of emergent inductance in YMn6Sn6, the improvement of operating frequency is a next important challenge. Further investigations by tuning magnetic period, anisotropy, and pinning strength in this class of compounds are needed.

Materials and Methods

Crystal Growth and Device Fabrication.

The single crystals of YMn6Sn6 were synthesized by a Sn-flux method (26). A mixture of ingredient elements with atomic ratio of Y:Mn:Sn = 1:6:30 was put in an evacuated quartz tube and heated to 1,050 °C, subsequently cooled slowly to 600 °C, and then quenched to room temperature. Any remaining flux was centrifuged, followed by soaking in hydrochloric acid solution. The single crystallinity was indicated by the well-developed facet structures and was also confirmed by Laue X-ray diffraction. No impurity phase of the single crystal was detected by powder X-ray diffraction. We cut thin plates out of the single crystals by using the focused ion beam (FIB) technique (NB-5000; Hitachi). The thin plates were mounted on silicon substrates with patterned electrodes. We fixed the thin plates to the substrates and electrically connected them to the electrodes by using FIB-assisted tungsten deposition. We made Au/Ti-bilayer electrode patterns by an electron-beam deposition method.

Transport and Magnetization Measurements.

Magnetic-field dependence of complex resistivity was measured with use of lock-in amplifiers (SR-830; Stanford Research Systems). We input a sine-wave current and recorded both in-phase (ReV1f) and out-of-phase (ImV1f) voltage with a standard four-terminal configuration. Background signals were estimated by measuring a short circuit where the terminal pads were connected by Au/Ti-bilayer electrode patterns. We subtracted the background signals from the measurement data. The possible temperature increase ΔT upon current excitation was checked by monitoring the temperature-dependent resistance value of the sample by passing the direct current (dc); note that the average joule heating by the dc density jdc is twice as large as that by the ac density (j0) of the same amplitude. In the current excitation corresponding to the case of j0 ∼3.6×104A/cm2, close to the maximal value used to obtain the result of Fig. 4, the estimated temperature increase is ΔT = +2.5 K at the base temperature of 270 K, indicating little influence of the heating on the current-induced effects discussed in this work.

Frequency dependence of complex inductance was measured with use of an LCR meter (E4980A; Agilent Technologies). We employed the two-terminal method to reduce parasitic impedance (the device #2 shown in SI Appendix, Fig. S1). We corrected the contributions from the cables and the electrodes with a standard open/short correction procedure. We also subtracted the contributions from electrical contacts between the sample and the electrodes, which were estimated by measurements with low current density (j0=1.0×103A/cm2). Here, the observed complex impedance Z∼(ω) is the sum of frequency-independent resistance (R) and frequency-dependent reactance of complex inductance [ωL∼(ω)=ωReL(ω)+iωImL(ω)]. The real and imaginary components of inductance can be estimated as ReL(ω)=ImZ∼(ω)/ω,ImL(ω)=(ReZ∼(ω)−R)/ω.

Supplementary Material

Supplementary File
pnas.2105422118.sapp.pdf (601.5KB, pdf)

Acknowledgments

We thank M. Kawasaki, Y. Kaneko, and Y. Onishi for enlightening discussions. This work was supported by Core Research for Evolutional Science and Technology, Japan Science and Technology Agency grants JPMJCR1874 and JPMJCR16F1 and Japan Society for the Promotion of Science KAKENHI grants JP18H03676, JP20H01859, and JP20H05155.

Footnotes

Competing interest statement: Y.T., N.K., and reviewer A.R. are coauthors on a research article [P. Schoenherr et al., Nature Phys. 14, 465–468 (2018)]. Y.T., N.N., and reviewer A.R. are coauthors on a roadmap article with a collection of independent subarticles [C. Back et al., J. Phys. D 53, 363001 (2020)]. However, these papers are not directly related to the present work, and the latter is an article by many authors.

This article contains supporting information online at https://www.pnas.org/lookup/suppl/doi:10.1073/pnas.2105422118/-/DCSupplemental.

Data Availability

All study data are included in the article and/or SI Appendix.

References

  • 1.Nagaosa N., Emergent inductor by spiral magnets. Jpn. J. Appl. Phys. 58, 12090 (2019). [Google Scholar]
  • 2.Yokouchi T., et al., Emergent electromagnetic induction in a helical-spin magnet. Nature 586, 232–236 (2020). [DOI] [PubMed] [Google Scholar]
  • 3.Berry M. V., Quantal phase factors accompanying adiabatic changes. Proc. R. Soc. Lond. A Math. Phys. Sci. 392, 45–47 (1984). [Google Scholar]
  • 4.Xiao D., Chang M.-C., Niu Q., Berry phase effects on electronic properties. Rev. Mod. Phys. 82, 1959–2006 (2010). [Google Scholar]
  • 5.Nagaosa N., Tokura Y., Topological properties and dynamics of magnetic skyrmions. Nat. Nanotechnol. 8, 899–911 (2013). [DOI] [PubMed] [Google Scholar]
  • 6.Neubauer A., et al., Topological Hall effect in the A phase of MnSi. Phys. Rev. Lett. 102, 186602 (2009). [DOI] [PubMed] [Google Scholar]
  • 7.Schulz T., et al., Emergent electrodynamics of skyrmions in a chiral magnet. Nat. Phys. 8, 301–304 (2012). [Google Scholar]
  • 8.Volovik G. E., Linear momentum in ferromagnets. J. Phys. Chem. 20, L83–L87 (1987). [Google Scholar]
  • 9.Barnes S. E., Maekawa S., Generalization of Faraday’s Law to include nonconservative spin forces. Phys. Rev. Lett. 98, 246601 (2007). [DOI] [PubMed] [Google Scholar]
  • 10.Yang S. A., et al., Universal electromotive force induced by domain wall motion. Phys. Rev. Lett. 102, 067201 (2009). [DOI] [PubMed] [Google Scholar]
  • 11.Hayashi M., et al., Time-domain observation of the spinmotive force in permalloy nanowires. Phys. Rev. Lett. 108, 147202 (2012). [DOI] [PubMed] [Google Scholar]
  • 12.Yamane Y., et al., Continuous generation of spinmotive force in a patterned ferromagnetic film. Phys. Rev. Lett. 107, 236602 (2011). [DOI] [PubMed] [Google Scholar]
  • 13.Kishine J., Bostrem I. G., Ovchinnikov A. S., Sinitsyn V. E., Coherent sliding dynamics and spin motive force driven by crossed magnetic fields in a chiral helimagnet. Phys. Rev. B Condens. Matter Mater. Phys. 86, 214426 (2012). [Google Scholar]
  • 14.Yamane Y., Ieda J., Sinova J., Electric voltage generation by antiferromagnetic dynamics. Phys. Rev. B 93, 180408 (2016). [Google Scholar]
  • 15.San Sebastian E., et al., Enantiospecific response in cross-polarization solid-state nuclear magnetic resonance of optically active metal organic frameworks. J. Am. Chem. Soc. 142, 17989–17996 (2020). [DOI] [PubMed] [Google Scholar]
  • 16.Naaman R., Paltiel Y., Waldeck D. H., Chiral molecules and the electron spin. Nat. Rev. Chem. 3, 250 (2019). [Google Scholar]
  • 17.Ghazaryan A., Paltiel Y., Lemeshko M., Analytic model of chiral-induced spin selectivity. J. Phys. Chem. C Nanomater Interfaces 124, 11716–11721 (2020). [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 18.Rikken G. L. J. A., Fölling J., Wyder P., Electrical magnetochiral anisotropy. Phys. Rev. Lett. 87, 236602 (2001). [DOI] [PubMed] [Google Scholar]
  • 19.Gladyshevskii R. E., Strusievicz O. R., Cenzual K., Parthé E., Structure of Gd3Ru4Al12, a new member of the EuMg5.2 structure family with minority atom clusters. Acta Crystallogr. B 49, 474–478 (1993). [Google Scholar]
  • 20.Niermann J., Jeitschko W., Ternary rare earth (R) transition metal aluminides R3T4Al12 (T = Ru and Os) with Gd3Ru4Al12 type structure. Z. Anorg. Allg. Chem. 628, 2549–2556 (2002). [Google Scholar]
  • 21.Nakamura S., et al., Spin trimer formation in the metallic compound Gd3Ru4Al12 with a distorted kagome lattice structure. Phys. Rev. B 98, 054410 (2018). [Google Scholar]
  • 22.Chandragiri V., Iyer K. K., Sampathkumaran E. V., Magnetic behavior of Gd3Ru4Al12, a layered compound with distorted kagomé net. J. Phys. Condens. Matter 28, 286002 (2016). [DOI] [PubMed] [Google Scholar]
  • 23.Hirschberger M., et al., Skyrmion phase and competing magnetic orders on a breathing kagomé lattice. Nat. Commun. 10, 5831 (2019). [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 24.Venturini G., Fruchart D., Malaman B., Incommensurate magnetic structures of RMn6Sn6 (R = Sc, Y, Lu) compounds from neutron diffraction study. J. Alloys Compd. 236, 102–110 (1996). [Google Scholar]
  • 25.Matsuo A., et al., Study of the Mn–Mn exchange interactions in single crystals of RMn6Sn6 compounds with R= Sc, Y and Lu. J. Alloys Compd. 408–412, 110–113 (2006). [Google Scholar]
  • 26.Uhlířová K., et al., Magnetic properties and Hall effect of single-crystalline YMn6Sn6. J. Magn. Magn. Mater. 310, 1747–1749 (2007). [Google Scholar]
  • 27.Bykov A. A., Chetverikov Y. O., Pirogov A. N., Grigor’ev S. V., Quasi-two-dimensional character of the magnetic order–disorder transition in YMn6Sn6. JETP Lett. 101, 699–702 (2015). [Google Scholar]
  • 28.Neubauer K. J., et al., In-plane magnetic field induced double fan spin structure with c-axis component in metallic kagome antiferromagnet YMn6Sn6. Phys. Rev. B 103, 014416 (2021). [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 29.Ghimire N. J., et al. Competing magnetic phases and fluctuation-driven scalar spin chirality in the kagome metal YMn6Sn6. Sci. Adv. 6, eabe2680 (2015). [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 30.Zhang H., et al., Topological magnon bands in a room-temperature kagome magnet. Phys. Rev. B 101, 100405 (2020). [Google Scholar]
  • 31.Kleemann W., Universal domain wall dynamics in disordered ferroic materials. Annu. Rev. Mater. Res. 37, 415–448 (2007). [Google Scholar]
  • 32.Ieda J., Yamane Y., Intrinsic and extrinsic tunability of Rashba spin-orbit coupled emergent inductors. Phys. Rev. B 103, L100402 (2021). [Google Scholar]
  • 33.Kurebayashi D., Nagaosa N., Electromagnetic response in spiral magnets and emergent inductance. arXiv [Preprint] (2021). https://arxiv.org/abs/2103.11317 (Accessed 31 July 2021).
  • 34.Momma K., Izumi F., VESTA 3 for three-dimensional visualization of crystal, volumetric and morphology data. J. Appl. Cryst. 44, 1272–1276 (2011). [Google Scholar]

Associated Data

This section collects any data citations, data availability statements, or supplementary materials included in this article.

Supplementary Materials

Supplementary File
pnas.2105422118.sapp.pdf (601.5KB, pdf)

Data Availability Statement

All study data are included in the article and/or SI Appendix.


Articles from Proceedings of the National Academy of Sciences of the United States of America are provided here courtesy of National Academy of Sciences

RESOURCES