Skip to main content
NCBI home page
Frontiers in Chemistry logoLink to Frontiers in Chemistry
. 2021 Sep 3;9:686788. doi: 10.3389/fchem.2021.686788

Synthesis, Mesomorphic, and Solar Energy Characterizations of New Non-Symmetrical Schiff Base Systems

Fowzia S Alamro 1, Hoda A Ahmed 2,3,*, Sobhi M Gomha 2,4,*, Mohamed Shaban 5,6
PMCID: PMC8448195  PMID: 34540796

Abstract

New asymmetrical Schiff base series based on lateral methoxy group in a central core, (E)-3-methoxy-4-(((4-methoxyphenyl)imino)methyl)phenyl 4-alkoxybenzoate (An), were synthesized and their optical and mesomorphic characteristics were investigated. The lateral OCH3group was inserted in the central ring in ortho position with respect to the azomethine linkage. FT-IR, and NMR spectroscopy as well as elemental analyses were used to elucidate their molecular structures. Their mesomorphic behaviors were characterized by polarized optical microscopy (POM) and differential scanning calorimetry (DSC). These examinations indicated that all the designed series were monomorphic and possessed nematic (N) mesophase enantiotropically, except A12 derivative which exhibited monotropic N phase. A comparative study was made between the present investigated series (An) and their corresponding isomers (Bn). The results revealed that the kind and stability of the mesophase as well as its temperature range are affected by the location and special orientation of the lateral methoxy group electric-resistance, conductance, energy-gap, and Urbach-energy were also reported for the present investigated An series. These results revealed that all electrodes exhibit Ohmic properties and electric-resistances in the GΩ range, whereas the electric resistance was decreased from 221.04 to 44.83 GΩ by lengthening the terminal alkoxy-chain to n = 12. The band gap of the An series was reduced from 3.43 to 2.89 eV by increasing the terminal chain length from n = 6 to n = 12 carbons. Therefore, controlling the length of the terminal chain can be used to improve the An series’ electric conductivity and optical absorption, making it suitable for solar energy applications.

Keywords: lateral methoxy, schiff base liquid crystals, nematic phase, optical properties, electrical properties, solar energy

Introduction

Today, numerous applications are being found for liquid crystals (LCs) due to their ability to undergo molecular orientation changes, such as electromagnetic fields, optical displays, surface modifications, and solar energy applications (Meng et al., 2018; You et al., 2019; Olaleru et al., 2020). On the other hand, the development of LC structural shapes with specific characteristics for certain applications remains a crucial challenge which needs wide information about the correlation between structural shape and mesomorphic properties, as well as their effect on the involved mechanisms of phase transitions (Lagerwall and Giesselmann, 2006).

Recently, the small molecule solar cells have exhibited great potential (Badgujar et al., 2016; Bin et al., 2017; Qiu et al., 2017; Bin et al., 2018; Li et al., 2018). Organic solar cells are cost-effective compared to traditional photovoltaic cells. Numerous studies on the applications of organic compounds for photosensitizers in solar cells have been reported (Meng et al., 2018; You et al., 2019; Olaleru et al., 2020). Innovative characteristics of organic solar cells as flexibility, cheap, and ease of use have attracted considerable attention from technological engineers and researchers. Furthermore, modern organic solar cells are low coast and having excellent efficiency (Meng et al., 2018). Due to the applications of solar energy, such as catalytic photo-degradation of dyes, solar hydrogen-generation, photo-electrochemical water splitting, and solar cells, band gap engineering and optical property control are critical parameters of interest (Ahmed and Abdalla, 2020; Helmy et al., 2020; Mohamed et al., 2020; Shaban and El Sayed, 2020; Shaban et al., 2020).

Huge numbers of rod-like thermotropic LCs, with rigid cores containing two or more aromatic rings and terminal flexible chains, have been reported (Kelker and Scheurle, 1969; Sharma and Patel, 2017; Kato et al., 2018). Most of these studies were based on azomethine linkages (Ahmed et al., 2018; Al-Mutabagani et al., 2021; Altowyan et al., 2021; El-atawy et al., 2021). The insertion of high polar compact lateral or terminal groups to main architecture influences the thermal and physical properties of the resulting LC material, such as phase transition temperatures, dielectric anisotropy, and the dipole moment (Jessy et al., 2018; Mishra et al., 2018; Saccone et al., 2018; Zaki et al., 2018; Zaki, 2019). Generally, the intermolecular separation increases due to the addition of lateral substituent, which widens the mesogenic cores and consequently leads to a reduction in lateral interactions (Naoum et al., 1997; Saad and Nessim, 1999; Naoum et al., 2010). However, as the breadth/length of the molecule will increment the thermal stability of produced phases decreases (Luckhurst and Gray, 1979). The small size of the lateral substituent enables its attachment into mesomorphic geometrics without being sterically disrupted, so liquid crystalline mesophases can still be observed. On the other hand, the terminal flexible chain group plays an essential role in the mesomorphic behaviors of synthesized materials (Yeap et al., 2004; Takezoe and Takanishi, 2006). As the length of the flexible terminal chain increases, the molecules tend to be oriented in a parallel alignment (Henderson and Imrie, 2011).

This study aims to synthesize new azomethine derivatives of di-methoxy groups having changeable lengths of the terminal alkoxy-group (n), namely, (E)-3-methoxy-4-(((4-methoxyphenyl)imino)methyl)phenyl 4-alkoxybenzoate, An.

The methoxy substituent is attached to a Schiff base terminal phenyl linker, while the other CH3O group is present into the central of structure as a laterally polar moiety. Moreover, the study aims to investigate the impact of lengthen of alkoxy chain on the mesomorphic properties of synthesized homologues. In addition, a comparison is conducted between the present investigated series and the previously reported isomers to evaluate the impact of exchanging the location of terminal polar groups on the mesomorphic behavior. The research also aims to study their optical and electric behaviors.

Experimental

Synthesis

Many reports have revealed that hydrazones and imines are valuable materials for medicinal and synthetic applications (Gomha and Riyadh, 2011; Abu-Melha et al., 2020; Gomha et al., 2020a; Gomha et al., 2020b; Ouf et al., 2020; Sayed et al., 2020; Gomha et al., 2021; Sayed et al., 2021). The following Scheme 1 shows the synthesis of a series of novel lateral CH3O materials 3 and An:

Scheme 1.

Scheme 1

Open in a new tab

Synthesis way of materials An.

Details for synthesis of (E)-3-methoxy-4-(((4-methoxyphenyl)imino)methyl)phenol (3) and (E)-3-methoxy-4-(((4-methoxyphenyl)imino)methyl)phenyl 4-alkoxybenzoate, An are included in the Supplementary Material.

1H-NMR, 13C-NMR, Infrared spectra (IR), and elemental analyses for the investigated materials were in agreement with the assigned structures. 1H-NMR data showed the expected ratios (Figure 1, Figure 2, and Figure 3). The physical data of products An are listed below:

FIGURE 1.

FIGURE 1

Open in a new tab

NMR spectra of material A6.

FIGURE 2.

FIGURE 2

Open in a new tab

NMR spectra of material A8.

FIGURE 3.

FIGURE 3

Open in a new tab

NMR spectra of material A12.

(E)-3-Methoxy-4-(((4-methoxyphenyl)imino)methyl)phenyl 4-(hexyloxy)benzoate (A6)

Yield: 87.3%; mp 103–105 °C, FTIR (ύ, cm−1): 3,016, 2,944 (C-H), 1,737 (C=O), 1,622 (C=N). 1H-NMR (400 MHz, DMSO): δ/ppm: 0.80–0.85 (t, 3H, CH 3(CH2)3CH2CH2O-), 1.26–1.40 (m, 6H, CH3 (CH 2 ) 3CH2CH2O-), 1.67–1.73 (m, 2H, CH3(CH2)3 CH 2CH2O-), 3.74 (s, 3H, OCH 3), 3.79 (s, 3H, OCH 3), 4.03–4.05 (t, 2H, CH3(CH2)3CH2 CH 2O-), 6.93–6.96 (d, 2H, Ar−H), 7.06–7.11(d, 2H, Ar−H), 7.26–7.30 (m, 3H, Ar−H), 7.47–7.50 (d, 1H, Ar−H), 7.66 (s, 1H, Ar−H), 8.00–8.03 (d, 2H, Ar−H), 8.61 (s, 1H, CH = N) ppm; 13C-NMR (400 MHz, DMSO): δ/ppm: 13.90 (CH3), 22.06, 25.09, 28.44, 30.96 (CH2), 55.29, 55.87 (OCH3), 68.01 (CH2-O), 110.93, 114.43, 114.72, 120.33, 122.01, 122.45, 123.47, 132.10, 135.28, 141.77, 143.93, 151.38, 157.61 (Ar-C), 157.99 (C=N), 163.26 (Ar-C-OR), 163.49 (C=O) ppm. Anal. Calcd. for C28H31NO5 (461.55): C, 72.86; H, 6.77; N, 3.03. Found: C, 72.73; H, 6.61; N, 2.93%.

(E)-4-(((4-Methoxyphenyl)imino)methyl)-3-methoxyphenyl 4-(octyloxy)benzoate (A8)

Yield: 89.7%; mp 96–97°C, FTIR (ύ, cm−1): 3,038, 2,929 (C-H), 1733 (C=O), 1,613 (C=N). 1H-NMR (400 MHz, DMSO): δ/ppm: 0.80–0.82 (t, 3H, CH3(CH2)5CH2CH2O-), 1.19–1.60 (m, 10H, CH3(CH2)5CH2CH2O-), 1.76–1.78 (m, 2H, CH3(CH2)5 CH 2CH2O-), 3.79 (s, 3H, OCH 3), 3.79 (s, 3H, OCH 3), 4.01–4.04 (t, 2H, CH3(CH2)5CH2 CH 2O-), 6.53–6.54 (d, 2H, Ar−H), 7.06–7.08 (d, 2H, Ar−H), 7.28–7.32 (m, 3H, Ar−H), 7.42 (d, 1H, Ar−H), 7.68–7.69 (s, 1H, Ar−H), 8.01–8.06 (d, 2H, Ar−H), 8.60 (s, 1H, CH = N) ppm; 13C-NMR (400 MHz, DMSO): δ/ppm: 14.48 (CH3), 22.62, 24.55, 25.48, 25.96, 29.19, 31.77 (CH2), 55.21, 56.43 (OCH3), 68.53 (CH2-O), 107.21, 111.79, 115.25, 123.08, 123.39, 124.09, 129.69, 132.64, 139.50, 142.81, 149.68, 150.62, 151.97 (Ar-C), 154.48 (C=N), 161.28 (Ar-C-OR), 163.82 (C=O) ppm. Anal. Calcd. for C30H35NO5 (489.60): C, 73.59; H, 7.21; N, 2.86. Found: C, 73.42; H, 7.09; N, 2.68%.

(E)-4-(((4-methoxyhenyl)imino)methyl)-3-methoxyphenyl 4-(dodecyloxy)benzoate(A12)

Yield: 86.0%; mp 88–89°C, FTIR (ύ, cm−1): 3,018, 2,925 (C-H), 1731 (C=O), 1,608 (C=N). 1H-NMR (400 MHz, DMSO): δ/ppm: 0.80–0.84 (t, 3H, CH3(CH2)9CH2CH2O-), 1.22–1.36 (m, 18H, CH3(CH2)9CH2CH2O-), 1.69–1.72 (m, 2H, CH3(CH2)9 CH 2CH2O-), 3.74 (s, 3H, OCH 3), 3.79 (s, 3H, OCH3), 4.02–4.04 (t, 2H, CH3(CH2)9CH2CH2O-), 6.95–6.96 (d, 2H, Ar−H), 7.05–7.07(d, 2H, Ar−H), 7.26–7.32 (m, 3H, Ar−H), 7.48–7.50 (d, 1H, Ar−H), 7.68 (s, 1H, Ar−H), 8.01–8.03 (d, 2H, Ar−H), 8.61 (s, 1H, CH = N) ppm; 13C-NMR (400 MHz, DMSO): δ/ppm: 13.97 (CH3), 22.10, 24.02, 24.96, 25.44, 28.49, 28.67, 28.72, 31.24, 34.50 (CH2), 55.32, 55.89 (OCH3), 68.02 (CH2-O), 110.97, 114.45, 114.74, 120.35, 122.02, 122.47, 123.49, 132.12, 135.30, 141.78, 143.94, 151.39, 157.63 (Ar-C), 158.01(C=N), 163.28 (Ar-C-OR), 163.51 (C=O) ppm. Anal. Calcd. for C34H43NO5 (545.71): C, 74.83; H, 7.94; N, 2.57. Found: C, 74.71; H, 7.84; N, 2.39%.

Results and Discussion

Mesomorphic Investigations of Present Series, An

The mesophase characteristics of the synthesized have been investigated via POM and DSC. Figure 4 shows representative DSC thermograms of homologue A8 upon heating and cooling cycles. It was observed that the phase transitions from Cr→ N, and N→ I on heating and reversed on cooling for the short chain length A6 derivative. Transition peaks changed according to the molecular geometry of the designed materials, An. Significant endothermic and exothermic peaks were observed to be dependent on the length of the terminal alkoxy chain (n), and were ascribed to mesomorphic transition. Optical images of A6 and A10 derivatives under POM are depicted in Figure 5. Schlieren/threads textures of the nematic phase were identified upon heating and cooling scans. The mesomorphic transition temperatures, as derived from DSC evaluations, and their associated enthalpies for all the synthesized compounds, An, are summarized in Table 1. The impact of the terminal length of the attached flexible group on their mesomorphic properties is displayed in Figure 4. Results in Table 1 and Figure 6 show that all investigated members of the group An are monomorphic and possess enantiotropic N phase, except the longer chain compound A16 which is monotropic nematogenic. In addition, the homologues An series exhibit a wide nematogenic range and stability dependent on their terminal chain length, where the A16 derivative has the lowest nematic stability. The melting transition of the present compounds, as usual, varies irregularly with the terminal chain length (n). From Figure 6, the shortest chain length derivative (A6) exhibits the highest nematic thermal stability and temperature range 163.6 and 49.1 °C, respectively. The A8 sample also possesses N phase enantiotrpoically with N stability and range nearly 144.9 and 32.8°C, respectively. Moreover, the derivative A10 has the lowest melting temperature 79.8°C, and possesses less enantiotropic thermal nematic stability (122.3°C). The compound bearing the longest chain terminal length (A12) has the lowest thermal nematic stability, so its phase appears monotropically. The geometry, polarizability, and the dipole moment of the designed materials are profoundly affected by the mesomeric kind of the terminals. In expansion, the mesomorphic character is impacted by an increase within the polarity and/or polarizability of the mesogenic part. Moreover, the decrement in N stability with the increasing length of the terminal chains (Figure 6) is associated with the increment of the dilution of interactions within the mesogenic units as well as the increment of the volume fraction of the alkoxy chains (Walker et al., 2019). The nematic range of the present series decreases in the order: A6 > A10 > A8 > A12. The phase character of calamitic molecules is specifically affected by molecular‐molecular interactions that mainly depend on their shapes and the location of the polar lateral and terminal attached groups.

FIGURE 4.

FIGURE 4

Open in a new tab

DSC thermograms of derivative A8 with heating /cooling rate of ±10°C/min.

FIGURE 5.

FIGURE 5

Open in a new tab

Nematic phase textures upon heating observed under POM for compounds (A) A6 at 155.0°C and (B) A10 at 115.0°C.

TABLE 1.

Temperatures of mesomorphic transitions, °C (enthalpy ΔH, kJ/mole), mesophase range (ΔT, °C), and the normalized-entropy, ΔS/R, of transition for investigated series An.

Comp T Cr-N ΔH Cr-N T N-I ΔH N-I ΔT ΔSN-I/R
A6 114.5 48.43 163.6 1.15 49.1 0.32
A8 112.1 46.06 144.9 1.61 32.8 0.46
A10 79.8 56.05 122.3 1.04 42.5 0.32
A12 106.5 53.94 102.8a 1.02 3.7 0.33
Open in a new tab

Cr-N = solid to the nematic mesophase transition.

N-I = nematic to the isotropic liquid mesophase transition.

a

Monotropic phase.

FIGURE 6.

FIGURE 6

Open in a new tab

Effect of terminal alkoxy-group on the mesophase behavior of the series An.

The normalized entropy changes, ΔSN-I/R, of the present investigated series (An) are summarized in Table 1. The data indicated that independent of the terminal alkoxy chains length, the entropy of N-I transitions show small values with irregular trends that mainly depend on the type of terminal and lateral substituents. Their relatively lower values may be due to the formation of molecular biaxiality (Henderson et al., 2001; Chan et al., 2012; Lee et al., 2012). These results are inconsistent with the previous investigations for dimeric LC materials based on pyrene derivatives (Attard et al., 1992; Attard and Imrie, 1992). Also, the stereo configuration of the lateral methoxy group plays an essential role in the molecular separations. Furthermore, the thermal cis-trans isomerization of the Schiff base linker has an essential role in the observed lower entropy changes, as reported before (Attard et al., 1990; Imrie et al., 1993; Henderson et al., 2001).

Effect of Position of Lateral Methoxy Group in the Mesomorphic Properties

To investigate the effect of the location of lateral CH3O groups on the phase and thermal properties of the materials, a comparison was made between the presently investigated series An and their previously corresponding isomers Bn (Vora and Gupta, 1982) for their mesomorphic properties. The comparison indicated that the thermal stability of the produced phase varies according to the improved molecular dipole moment and polarizability of the lateral methoxy group, which are dependent upon their position. The mesomorphic properties are nearly the same for the shortest terminal chain derivatives (n = 6 and n = 8) for both groups, while the longest chain compounds B10 and B12 have higher thermal stability than A10 and A12, respectively. It could be concluded that the observed nematic range and stability depend on the location and special orientation of the lateral CH3O moiety which was inserted in the mesogenic molecular part.

Electric Properties

The investigated An series’ electrical properties and current-voltage (I–V) characteristics are measured from −10 to 10 V at different scan steps; 1.0, 0.5, 0.1, 0.05, and 0.01 V; and shown in Figures 7A,C. The trends are almost linear (Ohmic behaviors). As a consequence, the resistances of the An electrodes are almost constant and unaffected by the current passing through them. Polymeric and organic systems act like Schottky diodes at low voltage, according to recent research. However, as shown in Figure 7B, the relationship between log (I) and V1/2 is non-linear in the current study, implying that our An electrodes do not behave like Schottky diodes. Figure 7A shows how increasing the applied voltage and increasing the terminal alkoxy-chain length to 12 increased the current intensity. The current intensity for the An series increased to 0.24 nA@10V when the applied voltage was increased to 10 V and the terminal alkoxy-chain length was increased to 12. As the scan step increased from 0.01 to 1 V, the current intensity is slightly increased, Figure 7C. The resistance of the An series is decreased by increasing the terminal alkoxy-chain length to 12. The values of the resistance are decreased from 221.04 GΩ for A6 to 44.83 GΩ for A12. The electric resistance of A10 film is decreased from 191.42 to 144.13 GΩ by increasing the scan step from 0.01 to 1 V as shown in Figure 7D. The values of the electric conductance (σ) were obtained and shown in Supplementary Figure S2 (Supplementary Material) and Table 2. The value of the electrical conductance is increased from 4.52 pS to 22.3 pS by increasing the terminal alkoxy-chain length from n = 6 to n = 12 carbons, as shown in Table 2, since the electrical conductance depends mainly on the number and mobility of charge carriers (Rathi et al., 2017; Kumar et al., 2018). By increasing the scan step from 0.01 to 1 V, the film conductance is increased from 5.22 to 6.94 pS. This indicates the coherent photocurrent generation, which is the basis of the photovoltaic cell (Bian et al., 2020).

FIGURE 7.

FIGURE 7

Open in a new tab

Electrical characteristics of An series: (A) Current-Voltage characteristics of An series, (B) Log(I) vs. V0.5 For S10 sample at different step scans, (C) Current-Voltage characteristics of A10 sample at different step scans, and (D) electric resistance for the An samples and A10 at different step scans.

TABLE 2.

Values of the electric conductance,σ, energy gap, Eg, and Urbach energy, E U, of An series.

Sample σ (pS) Eg (eV) EU (meV) SD R2
A12 22.31 2.89 251.3 3.11 0.9983
A10 17.54 2.91 839.4 8.64 0.9965
A8 5.57 3.01 150.2 2.46 0.9973
A6 4.52 3.43 1,065.0 9.84 0.9975
Open in a new tab

Optical Spectra and Energy Gap Calculation

The wavelength of incident light and the length of the An series’ terminal alkoxy-chain influence the transmittance and absorbance spectra of the An series, as shown in Figures 8A,B. All films showed transmission close to zero up to 400 nm, then the transmission increased and became less than 20% for An samples in the visible light region, Figure 8A. The transmission increased exponentially in the near IR region to reach maxima of ∼50, 66, 10, and 4% at 1,244 nm for A6, A8, A10, and A12 electrodes. After that, the transmission decreased as the wavelength increased. The absorbance spectra in Figure 8B show that An has strong absorption behavior in the UV/Vis region up to ∼860 nm. For the present An series, all films displayed very strong absorbance in the UV region up to ∼400 nm and the strongest absorbance was observed for A6 and the widest band was observed for A8 . The absorbance then dropped to a plateau from 400 to 860 nm, then dropped again to a minimum absorbance of around 1,250 nm. Figure 8B shows strong and wide absorption bands centered at ∼341.6, 340.4, 333.6, and 315.5 nm for A12, A10, A8, and A6, respectively, which is blue-shifted by decreasing the terminal alkoxy-chain length of the prepared An series. The bandwidths of these absorption bands are 39.2 nm for A12, 101.9 nm for A10, 112.9 nm for A8, and 54.8 nm for A6. The right edge of the absorption band is red-shifted by increasing the terminal alkoxy-chain length in the An series. This red-shift is mainly attributed to the size effects, where large size increases spin-orbit coupling and controls the exciton positions (Shaban and El Sayed, 2016). The absorption in the visible and IR region is in the order A12 > A10 > A8. This strong absorption and wide absorption band in the visible region is a desirable feature for the designing of energy-efficient solar cells (Liu et al., 2016).

FIGURE 8.

FIGURE 8

Open in a new tab

Optical (A) absorbance and (B) transmittance spectra of An films.

According to the optical absorption theorem, the relationship between absorption coefficient, α a , and the photon energy, E ph = hν, h = 6.625x10−34 J/s, for the direct allowed transition is given by (Shaban and El Sayed, 2015):

(αa Eph)2 = A( Eph - Eg ) (1)

Where E g is the optical energy gap. The values of direct E g for A12, A10, A8, and A6 are obtained by extending the linear segments of the plot of (α a E ph)2 vs. E ph to zero as shown in Figure 9A–D. The linear part observed for this figure indicates that the transition is performed directly. Interestingly as reported in Table 2, there is one direct bandgap for each electrode. The value of the bandgap is decreased from 3.43 to 2.89 eV by increasing the terminal chain length from six carbons (A6) to 12 carbons (A12). This reduction in the energy gap is ascribed to the influence of the density of localized states and is preferred for solar energy applications (Ahmed and Abdalla, 2020; Helmy et al., 2020; Mohamed et al., 2020; Shaban and El Sayed, 2020; Shaban et al., 2020). This behavior is consistent with the previously reported studies (Li et al., 2019). The strong absorption in the Visible/IR region and the extension of the bandgap edges are very important for solar energy applications, especially photoelectrochemical hydrogen generation and solar cells (Abdelmoneim et al., 2021; Mohamed et al., 2021; Shaban et al., 2021).

FIGURE 9.

FIGURE 9

Open in a new tab

Calculation of energy gap for (A) A12, (B) A10, (C) A8, (D) A6 derivatives, and (E) calculation of Urbach energy for An series.

Urbach energy (E U) refers to the disorder in the material and represents the width of the exponential absorption edge Urbach tail of the valence and conduction bands (El Sayed and Shaban, 2015). The exponential dependency of the E U can be determined according to the following equation (El Sayed and Shaban, 2015):

αa = αaoexp (Eph/Eu)→Eu= δEph /δ(ln(αa)) (2)

Where α ao is the band tail parameter that can be given by (Sharma et al., 2014):

αao =(4π σo / x ΔE c)1/2 (3)

Where c is the speed of light, σ o is electrical conductivity at absolute zero, and ΔE represents the width of the tail of the localized state in the forbidden gap. Figure 9E shows the plot of ln(α) vs. hν for the two band gaps of A6, A8, A10, and A12. The values of E U were obtained from the slopes of the linear fitting of these curves and are reported in Table 2. The statistical parameters, standard deviation (SD) and correlation coefficient (R2), are also reported in this table. The values are 251.3 ± 3.11 for A12 and 1,065.0 ± 9.84 for A6, which refers to the extension of the bandgap edges to cover a wide range of the spectral range. The minimum value of E U was reported for A8.

Tetracene (C) and pentacene (D) are small organic molecule semiconductors and most broadly investigated as p-type conjugated compounds in solar cells with high carrier mobilities of up to 0.1 and 3 cm2V-1 s-1, respectively. Due to their planar conjugated geometrical structures, they have a relatively low band energy gap of 1.7 eV. Thus they are suitable to be used as p-type semiconductors in photovoltaics (Mishra and Bäuerle, 2012).

The compounds being studied (An) are dielectrics due to their high resistance and energy band-gap values. In the presence of an external electric field, dielectric materials can store electric energy due to their polarization. Specifically, the dielectric energy-storing devices that allow for faster energy delivery (i.e., a quicker charge or discharge time), and hence can have promising applications on hybrid electric vehicles and power pulse devices. In the future, An compounds can be further refined by integrating conductive plasmonic nanomaterials to improve the conductivity and minimize the band-gap, allowing these samples to be utilized in solar energy applications such as solar cells, photoelectric cells, and photo-electrochemical cells.

Conclusion

New mesomorphic non-symmetrical homologues series based on a lateral CH3O group in a central core, (E)-3-methoxy-4-(((4-methoxyphenyl)imino)methyl)phenyl 4-alkoxybenzoate (An), were synthesized and investigated for their potential in solar energy applications. Molecular structure elucidation for the series was carried out by elemental analyses, FT-IR, and NMR spectroscopy. Examination of their mesomorphic behaviors was conducted via DSC and POM which indicated that all the synthesized homologues members are purely nematogenic and possess enantiotropic N mesophase, except the longer terminal chain compound (A12) which exhibited monotropic N phase. A comparative study between the present series (An) and their corresponding isomers (Bn) revealed that the mesophase stability and kind, as well as its temperature range, are affected by the location and special orientation of the lateral CH3O group. Measurements from the solar energy conversion devices showed that all studied An series exhibited Ohmic behavior with electric resistances in the GΩ range. The resistance of the An series was decreased by lengthening the terminal alkoxy-chain to n = 12 carbons. The highest electric conductivity, 22.3 pS, was reported for A12. The value of the bandgap was reduced from 3.43 to 2.89 eV by increasing the terminal chain length from n = 6 (A6) to n = 12 (A12). The minimum band edge tail, 150.2 ± 2.46 was reported for the A8 derivative. Therefore, increasing the length of the terminal chain will increase the An series’ electric conductivity and optical absorption, making it appropriate for solar energy applications.

Acknowledgments

The authors acknowledge the Deanship of Scientific Research at Princess Nourah bint Abdulrahman University for financial support through the Fast-track Research Funding Program.

Data Availability Statement

The original contributions presented in the study are included in the article/Supplementary Material, further inquiries can be directed to the corresponding authors.

Author Contributions

Formal analysis, FA, HA, and MS; Funding acquisition, FA, SG, and MS; Methodology, SG and HA; Project administration, FA, HA, and SG; Resources, SG and HA; Writing—original draft, FA, HA, MS, and SG; Writing—review and editing, HA, MS, and SG. All the authors approved the final version.

Funding

This research was funded by the Deanship of Scientific Research at Princess Nourah bint Abdulrahman University through the Fast-track Research Funding Program.

Conflict of Interest

The authors declare that the research was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest.

Publisher’s Note

All claims expressed in this article are solely those of the authors and do not necessarily represent those of their affiliated organizations, or those of the publisher, the editors and the reviewers. Any product that may be evaluated in this article, or claim that may be made by its manufacturer, is not guaranteed or endorsed by the publisher.

Supplementary Material

The Supplementary Material for this article can be found online at: https://www.frontiersin.org/articles/10.3389/fchem.2021.686788/full#supplementary-material

Click here for additional data file. (106.3KB, docx)

References

  1. Abdelmoneim A., Naji A., Wagenaars E., Shaban M. (2021). Outstanding Stability and Photoelectrochemical Catalytic Performance of (Fe, Ni) Co-Doped Co3O4 Photoelectrodes for Solar Hydrogen Production. Int. J. Hydrogen Energ. 46, 12915–12935. 10.1016/j.ijhydene.2021.01.113 [DOI] [Google Scholar]
  2. Abu-Melha S., Edrees M. M., Riyadh S. M., Abdelaziz M. R., Elfiky A. A., Gomha S. M. (2020). Clean Grinding Technique: A Facile Synthesis and In Silico Antiviral Activity of Hydrazones, Pyrazoles, and Pyrazines Bearing Thiazole Moiety Against SARS-CoV-2 Main Protease (Mpro). Molecules. 25, 4565. 10.3390/molecules25194565 [DOI] [PMC free article] [PubMed] [Google Scholar]
  3. Ahmed A., Abdalla E. (2020). Mohamed Shaban Simple and Low-Cost Synthesis of Ba-Doped CuO Thin Films for Highly Efficient Solar Generation of Hydrogen. J. Phys. Chem. C. 124 (41), 25521. 10.1021/acs.jpcc.0c04760 [DOI] [Google Scholar]
  4. Ahmed H. A., Hagar M., Aljuhani A. (2018). Mesophase Behavior of New Linear Supramolecular Hydrogen-Bonding Complexes. RSC Adv. 8 (61), 34937–34946. 10.1039/c8ra07692h [DOI] [PMC free article] [PubMed] [Google Scholar]
  5. Al-Mutabagani L. A., Alshabanah L. A., Ahmed H. A., Alalawy H. H., Al alwani M. H. (2021). Synthesis, Mesomorphic and Computational Characterizations of Nematogenic Schiff Base Derivatives in Pure and Mixed State. Molecules. 26, 2038. 10.3390/molecules26072038 [DOI] [PMC free article] [PubMed] [Google Scholar]
  6. Altowyan A. S., Ahmed H. A., Gomha S. M., Mostafa A. M. (2021). Optical and Thermal Investigations of New Schiff Base/Ester Systems in Pure and Mixed States. Polymers. 13 (11), 1687. 10.3390/polym13111687 [DOI] [PMC free article] [PubMed] [Google Scholar]
  7. Attard G. S., Garnett S., Hickman C. G., Imrie C. T., Taylor L. (1990). Asymmetric Dimeric Liquid Crystals With Charge Transfer Groups. Liquid Crystals. 7, 495–508. 10.1080/02678299008033826 [DOI] [Google Scholar]
  8. Attard G. S., Imrie C. T., Karasz F. E. (1992). Low Molar Mass Liquid-Crystalline Glasses: Preparation and Properties of the .Alpha.-(4-Cyanobiphenyl-4'-oxy)-.Omega.-(1-Pyreniminebenzylidene-4'-Oxy)Alkanes. Chem. Mater. 4, 1246–1253. 10.1021/cm00024a025 [DOI] [Google Scholar]
  9. Attard G. S., Imrie C. T. (1992). Liquid-Crystalline and Glass-Forming Dimers Derived From 1-Aminopyrene. Liquid Crystals. 11, 785–789. 10.1080/02678299208029030 [DOI] [Google Scholar]
  10. Badgujar S., Song C. E., Oh S., Shin W. S., Moon S.-J., Lee J.-C., et al. (2016). Highly Efficient and Thermally Stable Fullerene-Free Organic Solar Cells Based on a Small Molecule Donor and Acceptor. J. Mater. Chem. A. 4, 16335–16340. 10.1039/c6ta06367e [DOI] [Google Scholar]
  11. Bian Q., Ma F., Chen S., Wei Q., Su X., Buyanova I. A., et al. (2020). Vibronic Coherence Contributes to Photocurrent Generation in Organic Semiconductor Heterojunction Diodes. Nat. Commun. 11, 617. 10.1038/s41467-020-14476-w [DOI] [PMC free article] [PubMed] [Google Scholar]
  12. Bin H., Yang Y., Zhang Z.-G., Ye L., Ghasemi M., Chen S., et al. (2017). 9.73% Efficiency Nonfullerene All Organic Small Molecule Solar Cells With Absorption-Complementary Donor and Acceptor. J. Am. Chem. Soc. 139, 5085–5094. 10.1021/jacs.6b12826 [DOI] [PubMed] [Google Scholar]
  13. Bin H., Yao J., Yang Y., Angunawela I., Sun C., Gao L., et al. (2018). High‐Efficiency All‐Small‐Molecule Organic Solar Cells Based on an Organic Molecule Donor With Alkylsilyl‐Thienyl Conjugated Side Chains. Adv. Mater. 30, 1706361. 10.1002/adma.201706361 [DOI] [PubMed] [Google Scholar]
  14. Chan T.-N., Lu Z., Yam W.-S., Yeap G.-Y., Imrie C. T. (2012). Non-Symmetric Liquid Crystal Dimers Containing an Isoflavone Moiety. Liquid Crystals. 39, 393–402. 10.1080/02678292.2012.658712 [DOI] [Google Scholar]
  15. El Sayed A. M., Shaban M. (2015). Structural, Optical and Photocatalytic Properties of Fe and (Co, Fe) Co-Doped Copper Oxide Spin Coated Films. Spectrochimica Acta A: Mol. Biomol. Spectrosc. 149, 638–646. 10.1016/j.saa.2015.05.010 [DOI] [PubMed] [Google Scholar]
  16. El-atawy M. A., Naoum M. M., Al-Zahrani S. A., Ahmed H. A. (2021). New Nitro-Laterally Substituted Azomethine Derivatives; Synthesis, Mesomorphic and Computational Characterizations. Molecules. 26, 1927. 10.3390/molecules26071927 [DOI] [PMC free article] [PubMed] [Google Scholar]
  17. Gomha S. M., Abdelhady H. A., Hassain D. Z., Abdelmonsef A. H., El-Naggar M., Elaasser M. M., et al. (2021). Thiazole-Based Thiosemicarbazones: Synthesis, Cytotoxicity Evaluation and Molecular Docking Study. Drug Des. Development Ther. Vol. 15, 659–677. 10.2147/dddt.s291579 [DOI] [PMC free article] [PubMed] [Google Scholar]
  18. Gomha S. M., Edrees M. M., Muhammad Z. A., Kheder N. A., Abu- Melha S., Saad A. M. (2020a). Synthesis, Characterization, and Antimicrobial Evaluation of Some New 1,4-Dihydropyridines-1,2,4-Triazole Hybrid Compounds. Polycyclic Aromatic Compounds., 1–13. 10.1080/10406638.2020.1720751 [DOI] [Google Scholar]
  19. Gomha S. M., Muhammad Z. A., Abdel-aziz H. M., Matar I. K., El-Sayed A. A. (2020b). Green Synthesis, Molecular Docking and Anticancer Activity of Novel 1,4-Dihydropyridine-3,5-Dicarbohydrazones Under Grind-Stone Chemistry. Green. Chem. Lett. Rev. 13, 6–17. 10.1080/17518253.2019.1710268 [DOI] [Google Scholar]
  20. Gomha S. M., Riyadh S. M. (2011). Synthesis Under Microwave Irradiation of [1,2,4]Triazolo[3,4-B] [1,3,4]Thiadiazoles and Other Diazoles Bearing Indole Moieties and Their Antimicrobial Evaluation. Molecules. 16, 8244–8256. 10.3390/molecules16108244 [DOI] [PMC free article] [PubMed] [Google Scholar]
  21. Helmy A., Rabia M., Shaban M., Ashraf A. M., Ahmed S., Ahmed A. M. (2020). Graphite/Rolled Graphene Oxide/Carbon Nanotube Photoelectrode for Water Splitting of Exhaust Car Solution. Int. J. Energ. Res. 44 (9), 7687–7697. 10.1002/er.5501 [DOI] [Google Scholar]
  22. Henderson P. A., Imrie C. T. (2011). Methylene-Linked Liquid Crystal Dimers and the Twist-Bend Nematic Phase. Liquid Crystals. 38 (11-12), 1407–1414. 10.1080/02678292.2011.624368 [DOI] [Google Scholar]
  23. Henderson P. A., Niemeyer O., Imrie C. T. (2001). Methylene-Linked Liquid Crystal Dimers. Liquid Crystals. 28, 463–472. 10.1080/02678290010007558 [DOI] [Google Scholar]
  24. Imrie C. T., Karasz F. E., Attard G. S. (1993). Comparison of the Mesogenic Properties of Monomeric, Dimeric, and Side-Chain Polymeric Liquid Crystals. Macromolecules. 26, 545–550. 10.1021/ma00055a021 [DOI] [Google Scholar]
  25. Jessy P. J., Radha S., Patel N. (2018). Morphological, Optical and Dielectric Behavior of Chiral Nematic Liquid Crystal Mixture: Study on Effect of Different Amount of Chirality. J. Mol. Liquids. 255, 215–223. 10.1016/j.molliq.2018.01.160 [DOI] [Google Scholar]
  26. Kato T., Uchida J., Ichikawa T., Sakamoto T. (2018). Functional Liquid Crystals Towards the Next Generation of Materials. Angew. Chem. Int. Ed. 57, 4355–4371. 10.1002/anie.201711163 [DOI] [PubMed] [Google Scholar]
  27. Kelker H., Scheurle B. (1969). A Liquid-Crystalline(Nematic) Phase With a Particularly Low Solidification Point. Angew. Chem. Int. Ed. Engl. 8 (11), 884–885. 10.1002/anie.196908841 [DOI] [Google Scholar]
  28. Kumar M., Kumar S., Upadhyaya A., Yadav A., Gupta S. K., Singh A. (2018). Study of Charge Transport in Composite Blend of P3HT and PCBM. AIP Conf. Proc. 2018, 050066. 10.1063/1.5032721 [DOI] [Google Scholar]
  29. Lagerwall J. P. F., Giesselmann F. (2006). Current Topics in Smectic Liquid Crystal Research. ChemPhysChem. 7, 20–45. 10.1002/cphc.200500472 [DOI] [PubMed] [Google Scholar]
  30. Lee H.-C., Lu Z., Henderson P. A., Achard M. F., Mahmood W. A. K., Yeap G.-Y., et al. (2012). Cholesteryl-Based Liquid Crystal Dimers Containing a Sulfur-Sulfur Link in the Flexible Spacer. Liquid Crystals. 39, 259–268. 10.1080/02678292.2011.641753 [DOI] [Google Scholar]
  31. Li H., Zhao Y., Fang J., Zhu X., Xia B., Lu K., et al. (2018). Improve the Performance of the All-Small-Molecule Nonfullerene Organic Solar Cells Through Enhancing the Crystallinity of Acceptors. Adv. Energ. Mater. 8, 1702377. 10.1002/aenm.201702377 [DOI] [Google Scholar]
  32. Li X., Guo J., Yang L., Chao M., Zheng L., Ma Z., et al. (2019). Low Bandgap Donor-Acceptor π-Conjugated Polymers From Diarylcyclopentadienone-Fused Naphthalimides. Front. Chem. 7, 362. 10.3389/fchem.2019.00362 [DOI] [PMC free article] [PubMed] [Google Scholar]
  33. Liu S., Kan Z., Thomas S., Cruciani F., Brédas J.-L., Beaujuge P. M. (2016). Thieno[3,4-c ]Pyrrole-4,6-Dione-3,4-Difluorothiophene Polymer Acceptors for Efficient All-Polymer Bulk Heterojunction Solar Cells. Angew. Chem. Int. Ed. 55 (42), 12996–13000. 10.1002/anie.201604307 [DOI] [PubMed] [Google Scholar]
  34. Luckhurst G., Gray G. W. (1979). The Molecular Physics of Liquid Crystals. New York, NY: Academic Press. [Google Scholar]
  35. Meng L., Zhang Y., Wan X., Li C., Zhang X., Wang Y., et al. (2018). Organic and Solution-Processed Tandem Solar Cells With 17.3% Efficiency. Science. 361, 1094–1098. 10.1126/science.aat2612 [DOI] [PubMed] [Google Scholar]
  36. Mishra A., Bäuerle P. (2012). Small Molecule Organic Semiconductors on the Move: Promises for Future Solar Energy Technology. Angew. Chem. Int. Ed. 51, 2020–2067.‏ 10.1002/anie.201102326 [DOI] [PubMed] [Google Scholar]
  37. Mishra R., Hazarika J., Hazarika A., Gogoi B., Dubey R., Bhattacharjee D., et al. (2018). Dielectric Properties of a Strongly Polar Nematic Liquid crystal Compound Doped With Gold Nanoparticles. Liquid Crystals. 45, 1661–1671. 10.1080/02678292.2018.1478995 [DOI] [Google Scholar]
  38. Mohamed F., Rabia M., Shaban M. (2020). Synthesis and Characterization of Biogenic Iron Oxides of Different Nanomorphologies From Pomegranate Peels for Efficient Solar Hydrogen Production. J. Mater. Res. Technology. 9 (3), 4255–4271. 10.1016/j.jmrt.2020.02.052 [DOI] [Google Scholar]
  39. Mohamed H. S. H., Rabia M., Zhou X.-G., Qin X.-S., Khabiri G., Shaban M., et al. (2021). Phase-Junction Ag/TiO2 Nanocomposite as Photocathode for H2 Generation. J. Mater. Sci. Technology. 83, 179–187. 10.1016/j.jmst.2020.12.052 [DOI] [Google Scholar]
  40. Naoum M. M., Mohammady S. Z., Ahmed H. A. (2010). Lateral Protrusion and Mesophase Behaviour in Pure and Mixed States of Model Compounds of the Type 4-(4′-Substituted Phenylazo)-2-(or 3-)Methyl Phenyl-4'-Alkoxy Benzoates. Liquid Crystals. 37, 1245–1257. 10.1080/02678292.2010.497228 [DOI] [Google Scholar]
  41. Naoum M. M., Saad G. R., Nessim R. I., Abdel-Aziz T. A., Seliger H. (1997). Effect of Molecular Structure on the Phase Behaviour of Some Liquid Crystalline Compounds and Their Binary Mixtures II. 4-Hexadecyloxyphenyl Arylates and Aryl 4-hexadecyloxy Benzoates. Liquid Crystals. 23, 789–795. 10.1080/026782997207713 [DOI] [Google Scholar]
  42. Olaleru S. A., Kirui J. K., Wamwangi D., Roro K. T., Mwakikunga B. (2020). Perovskite Solar Cells: The New Epoch in Photovoltaics. Solar Energy. 196, 295–309. 10.1016/j.solener.2019.12.025 [DOI] [Google Scholar]
  43. Ouf S. A., Gomha S. M., Eweis M., Ouf A. S., Sharawy I. A. A., Alharbi S. A. (2020). Antidermatophytic Activity of Some Newly Synthesized Arylhydrazonothiazoles Conjugated with Monoclonal Antibody. Sci. Rep. 10, 20863. 10.1038/s41598-020-77829-x [DOI] [PMC free article] [PubMed] [Google Scholar]
  44. Qiu B., Xue L., Yang Y., Bin H., Zhang Y., Zhang C., et al. (2017). All-Small-Molecule Nonfullerene Organic Solar Cells With High Fill Factor and High Efficiency Over 10%. Chem. Mater. 29, 7543–7553. 10.1021/acs.chemmater.7b02536 [DOI] [Google Scholar]
  45. Rathi S., Chauhan G., Gupta S. K., Srivastava R., Singh A. (2017). Analysis of Blockade in Charge Transport Across Polymeric Heterojunctions as a Function of Thermal Annealing: A Different Perspective. J. Elec Materi. 46, 1235–1247. 10.1007/s11664-016-5097-x [DOI] [Google Scholar]
  46. Saad G. R., Nessim R. I. (1999). Effect of Molecular Structure on the Phase Behaviour of Some Liquid Crystalline Compounds and Their Binary Mixtures VI[1]. The Effect of Molecular Length. Liquid Crystals. 26, 629–636. 10.1080/026782999204679 [DOI] [Google Scholar]
  47. Saccone M., Kuntze K., Ahmed Z., Siiskonen A., Giese M., Priimagi A. (2018). Ortho-Fluorination of Azophenols Increases the Mesophase Stability of Photoresponsive Hydrogen-Bonded Liquid Crystals. J. Mater. Chem. C. 6, 9958–9963. 10.1039/c8tc02611d [DOI] [Google Scholar]
  48. Sayed A. R., Gomha S. M., Taher E. A., Muhammad Z. A., El-Seedi H. R., Gaber H. M., et al. (2020). One-Pot Synthesis of Novel Thiazoles as Potential Anti-Cancer Agents. Drug Des. Development Ther. 14, 1363–1375. 10.2147/dddt.s221263 [DOI] [PMC free article] [PubMed] [Google Scholar]
  49. Sayed R., M Abd El-lateef H., Gomha S. M. (2021). L-Proline Catalyzed Green Synthesis and Anticancer Evaluation of Novel Bioactive Benzil Bis-Hydrazones Under Grinding Technique. Green. Chem. Lett. Rev. 14, 179–188. 10.1080/17518253.2021.1893392 [DOI] [Google Scholar]
  50. Shaban M., El Sayed A. M. (2015). Influences of Lead and Magnesium Co-Doping on the Nanostructural, Optical Properties and Wettability of Spin Coated Zinc Oxide Films. Mater. Sci. Semicond. Process. 39, 136–147. 10.1016/j.mssp.2015.04.008 [DOI] [Google Scholar]
  51. Shaban M., El Sayed A. M. (2016). Effects of Lanthanum and Sodium on the Structural, Optical and Hydrophilic Properties of Sol-Gel Derived ZnO Films: A Comparative Study. Mater. Sci. Semiconductor Process. 41, 323–334. 10.1016/j.mssp.2015.09.002 [DOI] [Google Scholar]
  52. Shaban M., El Sayed A. M. (2020). Influence of the Spin Deposition Parameters and La/Sn Double Doping on the Structural, Optical, and Photoelectrocatalytic Properties of CoCo2O4 Photoelectrodes. Solar Energ. Mater. Solar Cell. 217, 110705. 10.1016/j.solmat.2020.110705 [DOI] [Google Scholar]
  53. Shaban M., Hamd A., Amin R. R., Abukhadra M. R., Khalek A. A., Khan A. A. P., et al. (2020). Preparation and Characterization of MCM-48/Nickel Oxide Composite as an Efficient and Reusable Catalyst for the Assessment of Photocatalytic Activity. Environ. Sci. Pollut. Res. 27, 32670–32682. 10.1007/s11356-020-09431-7 [DOI] [PubMed] [Google Scholar]
  54. Shaban M., Rabia M., Eldakrory M. G., Maree R. M., Ahmed A. M. (2021). Efficient Photoselectrochemical Hydrogen Production Utilizing of APbI 3 (A = Na, Cs, and Li) Perovskites Nanorods. Int. J. Energ. Res. 45, 7436–7446. 10.1002/er.6326 [DOI] [Google Scholar]
  55. Sharma S., Vyas S., Periasamy C., Chakrabarti P. (2014). Structural and Optical Characterization of ZnO Thin Films for Optoelectronic Device Applications by RF Sputtering Technique. Superlattices and Microstructures. 75, 378–389. 10.1016/j.spmi.2014.07.032 [DOI] [Google Scholar]
  56. Sharma V. S., Patel R. B. (2017). Design and Investigation of Calamatic Liquid Crystals: Schiff Base (‒CH˭N), Chalcone (‒CO‒CH˭CH‒), and Ester (‒COO‒) Linkage Group Contain Rigid Rod Shape With Various Terminal Parts. Mol. Crystals Liquid Crystals. 643 (1), 141–158. 10.1080/15421406.2016.1263115 [DOI] [Google Scholar]
  57. Takezoe H., Takanishi Y. (2006). Bent-core Liquid Crystals: Their Mysterious and Attractive World. Jpn. J. Appl. Phys. 45, 597–625. 10.1143/jjap.45.597 [DOI] [Google Scholar]
  58. Vora R. A., Gupta R. (1982). Effect of Lateral Substitution on Mesomorphism: (A) 4(4'-N-Alkoxybenzoyloxy)-3-Methoxy Benzaldehydes (B) 4(4'-N-Alkoxybenzoyloxy)-3-Methoxy Benzylidene-4"-Toluidines (C) 4(4'-N-Alkoxybenzoyloxy)-3-Methoxy Benzylidene-4"-Anisidines. Mol. Crystals Liquid Crystals. 80 (1), 119–127. ‏. 10.1080/00268948208071025 [DOI] [Google Scholar]
  59. Walker R., Pociecha D., Strachan G. J., Storey J. M. D., Gorecka E., Imrie C. T. (2019). Molecular Curvature, Specific Intermolecular Interactions and the Twist-bend Nematic Phase: the Synthesis and Characterisation of the 1-(4-Cyanobiphenyl-4-Yl)-6-(4-Alkylanilinebenzylidene-4-Oxy)Hexanes (CB6Om). Soft Matter. 15, 3188–3197. 10.1039/C9SM00026G [DOI] [PubMed] [Google Scholar]
  60. Yeap G.-Y., Ha S.-T., Lim P.-L., Boey P.-L., Mahmood W. A. K., Ito M. M., et al. (2004). Synthesis and Mesomorphic Properties of Schiff Base Esters Ortho-Hydroxy-Para-Alkyloxybenzylidene-Para-Substituted Anilines. Mol. Crystals Liquid Crystals. 423, 73–84. 10.1080/15421400490494508 [DOI] [Google Scholar]
  61. You Y. J., Song C. E., Hoang Q. V., Kang Y., Goo J. S., Ko D. H., et al. (2019). Highly Efficient Indoor Organic Photovoltaics With Spectrally Matched Fluorinated Phenylene‐Alkoxybenzothiadiazole‐Based Wide Bandgap Polymers. Adv. Funct. Mater. 29, 1901171. 10.1002/adfm.201901171 [DOI] [Google Scholar]
  62. Zaki A. A., Ahmed H. A., Hagar M. (2018). Impact of Fluorine Orientation on the Optical Properties of Difluorophenylazophenyl Benzoates Liquid Crystal. Mater. Chem. Phys. 216, 316–324. 10.1016/j.matchemphys.2018.06.012 [DOI] [Google Scholar]
  63. Zaki A. A. (2019). Optical Measurements of Phase Transitions in Difluorophenylazophenyl Benzoate Thermotropic Liquid Crystal With Specific Orientated Fluorine Atoms. Phase Transitions. 92, 135–148. 10.1080/01411594.2018.1556271 [DOI] [Google Scholar]

Associated Data

This section collects any data citations, data availability statements, or supplementary materials included in this article.

Supplementary Materials

Click here for additional data file. (106.3KB, docx)

Data Availability Statement

The original contributions presented in the study are included in the article/Supplementary Material, further inquiries can be directed to the corresponding authors.

Articles from Frontiers in Chemistry are provided here courtesy of Frontiers Media SA

RESOURCES