Skip to main content
Journal of Food Science and Technology logoLink to Journal of Food Science and Technology
. 2022 Jun 27;59(11):4352–4361. doi: 10.1007/s13197-022-05509-x

Optimization of the frying process in relation to quality characteristics of Khaja (A traditional sweet)

Sourabh Kumar 1, Abhishek Chandra 1,3, Prabhat K Nema 1,✉, Vijay Singh Sharanagat 1, Sachin Kumar 1, Palmei Gaibimei 2
PMCID: PMC9525483  PMID: 36193472

Abstract

The present study was focused on the optimization of process parameters and quality characterization of Khaja. A full factorial design 53 was applied using different levels of fat proportions (5–25%), frying temperature (160–200 °C), and frying time (1–5 min). The response optimizer function in Minitab 18 software was used to select five samples with the highest desirability which were then subjected to sensory analysis. The lightness of the samples decreased significantly (P ˂ 0.05) from 68.59 to 43.33 whereas, redness increased significantly (P ˂ 0.05) from 0.26 to 11.48 with increasing levels of all independent variables. Water activity and moisture content of the samples decreased significantly (P ˂ 0.05) from 0.75 to 0.21 and 14.41–1.40%wb respectively, whereas total fat content increased significantly (P ˂ 0.05) from 25.05 to 45.7% with increasing levels of independent variables. The hardness of the samples significantly (P ˂ 0.05) varied from 60.45 to 7.69 N. The sensory analysis revealed that the sample with 20% fat proportion, fried at 180 °C for 4 min, scored maximum in overall acceptability. The microstructural images revealed the structural damage and formation of pores in fried samples. The fatty acid analysis showed higher saturated fatty acids in market samples than in optimized samples. The results of the study concluded that fat proportion and frying parameters (temperature and time) are crucial for a better understanding of the deep-frying process of Khaja in order to achieve good quality.

Supplementary Information

The online version contains supplementary material available at 10.1007/s13197-022-05509-x.

Keywords: Khaja, Fat proportion, Deep-frying, Texture, Sensory analysis, Microstructure

Introduction

Deep-frying is an extensively used method for domestic and industrial cooking due to its ability to create distinctive texture and flavors in foods (Fellows 2017; Dana and Saguy 2006). Fried food products are popular because of their specific taste, flavor, and texture, and they are intended to supplement people’s nutritional intake (Omidiran et al. 2019). Besides wide demand, substantial sales of a wide range of fried products have increased due to its operational ease in terms of commercial practice, convenience, and economic feasibility. The quality of the product manufactured in various places vary widely based on local ingredients, ease of availability, accessibility, and processing methods. As a result, fried products must be intended to promote repeatability, limit defects, and ensure homogeneity in the finished product in both small and large-scale production. Manufacturers require control on end-product quality which can be maintained by standardization of composition and process parameters.

Khaja is one of the famous sweetmeats prepared with layered dough that is deep-fried and then dipped in sugar syrup. It is similar to the Middle Eastern Baklava dessert, which is baked rather than fried. Khaja is popular in India’s eastern and southern parts, i.e., Bihar, Uttar Pradesh, Orissa, Karnataka, and Tamil Nadu. Khaja of Silao (a city in Bihar, India) has gained popularity due to its unique multilayered shape, taste, mouthfeel, and crispiness which is manufactured by small-scale or home-based businesses. A GI tag has also been granted to the Silao Khaja by the Geographical Indications Registry, Chennai, India (Reddy 2018). The steps in the manufacturing of Khaja include dough preparation, dough sheeting, fat layering, rolling, sheeting again, cutting, and deep-frying. The roll-in fat melts during the frying of Khaja, allowing easy dough layer separation and puffing due to the explosion of steam generated inside the layers. The heated oil comes in contact with a wider surface area causing various changes in the surface properties which results in the development of a light yellow–brown color with a crisp texture. To make it a sweet delicacy, a sugar syrup is poured over the fried Khaja and allowed to soak in; however, some people like it plain or with a salty flavor.

During frying, the hot oil acts as a medium of heat transfer, and the water evaporates from the surface while the oil is absorbed into the product. Simultaneously, changes in the cellular structure of carbohydrates, proteins, and fats (Zhang et al. 2018) as well as some other chemical reactions such as Maillard reaction, caramelization reaction, and oxidation reactions occur. The moisture in the surface evaporates during frying, forming the outer crust. The moisture is also transmitted from the inner core through molecular diffusion which results in the formation of various channels that are later filled with oil (Krokida et al. 2000). Several studies have reported that most of the oil is absorbed while removing the product from the oil bath since the rapid escape of water vapor would hinder the oil penetration during frying (Dana and Saguy 2006; Zhang et al. 2018; Touffet et al. 2020). The extent of oil absorption depends on various factors such as pretreatments (pre-drying, blanching), processing parameters (temperature, time, and method) as well as product characteristics including surface roughness, composition, the thickness of the layer, and oil properties (Zhang et al. 2018; Xu et al. 2020; Dehghannya and Ngadi 2021). These factors also play a crucial role in developing crispy crust, golden brown color, and distinct flavors and aromas making fried food appealing to the consumers (Fellows 2017; Ghaitaranpour et al. 2018).

The factorial designs are important in analyzing the effect of each factor including the interaction of factors. In a full factorial design, each level of every factor appears with every level of another factor. Furthermore, the optimization tool is regarded as an excellent approach for improving complicated processes, and it has been widely employed in a variety of food operations (Omidiran et al. 2019; Fikry et al. 2021). Despite the immense popularity of Khaja, there is a lack of information in the literature regarding optimum frying conditions. As a result, the current study aimed to investigate the impact of independent variables on the quality characteristics of deep-fried Khaja; develop suitable models to predict the properties of Khaja; and optimize the process parameters. The microstructure and fatty acid profile of optimized and market Khaja samples were also analyzed. The detailed investigation of the process of deep-frying Khaja is expected to improve the understanding from an industrial perspective.

Materials and methods

Materials

Refined wheat flour (Reliance Select), vanaspati (hydrogenated oil, Dalda), soybean oil (Fortune), and sugar (Good Life) were purchased from Reliance Fresh, Narela, Delhi (India). All the chemicals were purchased from Sisco Research Laboratories (Mumbai, India). The market sample was procured from Sri Kali Sah Khaja, Silao, Bihar (India) in October 2020.

Preparation of Khaja

The dough was prepared using refined wheat flour (500 g) and water (280 mL) and kept in a plastic bag at 25–27 °C for 30 min. This allows the starches and gluten to expand and fully absorb the water, making it easier to work with the dough. The roll-in fat was made by blending vanaspati with refined wheat flour (1:1). The dough and roll-in fat (fat proportion) were measured in different quantities as shown in Table S1. The measured dough was sheeted by a wooden roller pin in a rectangular shape (50 × 15 cm), and roll-in fat was applied over the top. The prepared sheet was rolled to form layers then flattened and elongated along the vertical axis, as shown in Fig. 1. It was sheeted again to form a rectangular shape (40 × 10 cm) and square samples (5 cm) were cut using a sharp knife.

Fig. 1.

Fig. 1

Schematic representation of Khaja preparation

The frying process

The samples were fried in soybean oil at different temperatures (160–200 °C) for different time duration (1–5 min) as shown in Table 1 using an electric deep-fryer (Model EF-81, Aarka, India). Fried samples were placed vertically in a wire screen to drain out excess oil through layers. The samples were allowed to cool down at room temperature (25 ± 2 °C) and packaged in LDPE pouches for further analysis.

Table 1.

Independent variables and the levels used for full-factorial design

Factor Level 1 Level 2 Level 3 Level 4 Level 5
Fat proportion (%) 5 (T1) 10 (T2) 15 (T3) 20 (T4) 25 (T5)
Frying temperature (°C) 160 170 180 190 200
Frying time (min) 1 2 3 4 5

Color analysis

The color was measured with a handheld colorimeter (Model CR-400, Konika Minolta, Japan). The instrument calibration was done with a white tile before taking readings. The color was determined in terms of L*, a*, and b* where, L* represents lightness or darkness [L* = 0 (black), L* = 100 (white)], a* represents redness or greenness [(+ a* = redder), (− a* = greener)], and b* represents yellowness or blueness of the sample [(+ b* = yellower), (− b* = bluer)].

Water activity (aw) and moisture content (MC) analysis

The aw was measured by a water activity meter (4TE, Aqualab, METER Group, Inc.). The instrument was calibrated using distilled water before taking the sample readings. The MC of samples was determined (%wb) by the standard hot air oven method (AOAC, 2010).

Total fat analysis

The total fat content was determined by the Soxhlet method (AOAC, 2010) using petroleum ether (60–80 °C) as a solvent.

Texture analysis

The textural property was measured by texture analyzer (TA.HD plus, Stable Microsystem, UK), with a stainless-steel blade set knife (HDP/BSK) and 25 kgf load cell. Khaja was placed perpendicular to the blade to ensure that the maximum number of layers touches the blade during analysis. The target mode distance (50 mm) was selected, trigger force (0.049 N), pre-test speed (1 mm/s), test speed (2 mm/s), and post-test speed (10 mm/s) were maintained. The force–deformation curve was obtained after the probe passed through the entire Khaja section, and the maximum force was recorded as the hardness.

Sensory analysis

The fried samples were half dipped in sugar syrup (65°Brix, 50 °C), inverted, and placed vertically so that the entire layers are sweetened and excess syrup is drained out. The fried, fried-sugar syrup soaked and market Khaja were served for sensory evaluation to 30 semi-trained panelists comprising staff and students (15 male and 15 females, age group 22–32) of NIFTEM, India. They were asked to evaluate the sensory characteristics (color, taste, mouthfeel, texture, overall acceptability) of Khaja using a nine-point hedonic scale, with 1 indicating “dislike extremely” and 9 indicating “like extremely”. Between two consecutive sample tests, the assessors were instructed to rinse their mouths with water.

Data analysis

A full factorial design with 5 levels (Table 1) of each independent parameter (fat proportion, frying temperature, frying time) comprising 125 experimental combinations (53) was used. Five response variables (color, aw, MC, total fat content, and hardness) were chosen as an indicator of the quality of Khaja. Obtained results were analyzed by analysis of variance (Factorial ANOVA, balanced design), and Tukey’s multiple comparison test at a 5% level of significance. Minitab 18 software was used for the statistical analysis. The following regression equation was used to fit the experimental data to represent the responses as a function of independent variables:

Yi=β0+β1X1+β2X2+β3X3+β12X1X2+β23X2X3+β13X1X3+β123X1X2X3 1

where Y denotes the response variable, X1, X2, and X3 are the coded form of independent variables, whereas, βo is intercept and β1, β2, β3, β12, β23, β13, β123 are coefficients. To visualize the effect more clearly, a three-dimensional plot was created using OriginPro 2016 by keeping a single variable constant while changing the other two variables within the experimental range.

Optimization of independent variables regarding the selected multiple responses was done by the response optimizer tool in Minitab 18 software. To reach for an optimum fat proportion and processing conditions (frying time and temperature), responses including lightness, redness, yellowness, and hardness were kept within the range of market Khaja sample values followed by minimization of aw, MC, and total fat content (Table S4). The set target values were average values of market Khaja samples. All the five suggested combinations with utmost desirability were selected for the sensory analysis. For validation of the generated models, experiments were conducted at optimum conditions, and obtained responses were compared with model-predicted values.

Microstructural analysis

Scanning electron microscopy (SEM) was used to characterize the microstructural changes in Khaja during frying. The microstructure of Khaja samples was observed under SEM (EVO® 50, Carl Zeiss, USA) with a constant voltage of 20 kV. Khaja samples were first defatted by the soxhlet extraction method and then freeze-dried. The samples were cut into 1 mm × 1 mm and coated with gold under vacuum conditions. The images were obtained at 500 × magnification.

Fatty acid composition

Gas chromatography with a flame ionization detection system (GC-FID) was employed to determine the fatty acid composition of the market and optimized Khaja sample. The fatty acid methyl esters were prepared following the AOAC (2005) 996.06 method and analyzed by a gas chromatography (GC) (Agilent Technologies, Beijing, China, GC 7890B model) system with an ionic liquid capillary column (SP2560 100 m × 0.25 mm × 0.20 µm, Supelco, Sigma-Aldrich). The extracted oil was dissolved in petroleum ether and placed into a pyrex culture tube with a teflon screw cap (16 mm × 120 mm). Under a moderate stream of nitrogen, the solvent was completely evaporated. Then 2 mL of 7% boron trifluoride in methanol and 1.0 mL of toluene was added and incubated in the oven at 100 °C (45 min) with a gentle shake in the interval of 10 min. After allowing the vial to cool to room temperature, 5 mL distilled water, 2 mL hexane, and 1 g sodium sulfate were added and shaken in a vortex mixer for 5 min. The upper layer was carefully separated and filtered through a 0.22 µm PTFE (Polytetrafluoroethylene) filter for further evaluation. In GC analysis, nitrogen was employed as the carrier gas with a flow rate of 1 mL/min, a split ratio of 1:100, and the total run time was 70.66 min. The temperature of the injector and detector was kept at 250 and 280 °C, respectively. The oven temperature was maintained at 100 °C for 4 min before gradually increasing to 175 °C (5 °C/min). After 15 min, the temperature was increased to 240 °C (2 °C/min) and maintained for 20 min. Identification of fatty acids was performed using the respective standard.

Results and discussion

Effect on color

Figure 2a–f shows the color parameters of fried samples in terms of lightness (L*), redness (a*), and yellowness (b*). The total variation in lightness ranged from 68.59 to 43.33; redness ranged from 0.26 to 11.48, and yellowness ranged from 15.11 to 26.15 with change in levels of independent variables. The lightness decreased to 58.83, 57.90, 57.01, 54.56, and 53.99 for T1, T2, T3, T4, and T5 samples, respectively when fried at 180 °C for 4 min. Similarly, the lightness also decreased with an increase in the level of frying temperature and time, as shown in Fig. 2a, b. The redness increased with an increase in levels of all independent variables, as shown in Fig. 2c, d. The redness values for T1–T5 were in the range of 0.26–1.74 when fried at 160 °C for 1 min, while it increased to 9.54–11.48 when fried at 200 °C for 5 min. Similarly, the yellowness also increased with increasing levels of independent variables; however, a reduction was observed when fried at 190, and 200 °C, as shown in Fig. 2e, f. When the fat proportion increased from T1 to T5, the yellowness increased from 20.62 to 26.15 for samples fried at 180 °C for 4 min. The variation in the color parameter in Khaja could be associated with the non-enzymatic browning reactions, especially Maillard reactions, caramelization, and chemical oxidation occurring at high temperatures (Kumar et al. 2006; Xu et al. 2020). These effects were intensified at high fat proportion levels since the layers were effectively separated, allowing for adequate in-depth frying. The observed outcome in this study is consistent with those of Nsabimana et al. (2018) for deep-frying of doughnuts at different temperatures (120–180 °C) and time (6–12 min). Omidiran et al. (2019) also observed the similar effect of frying time (2–4 min) and temperature (170–180 °C) on color parameters of snacks fried in soybean oil.

Fig. 2.

Fig. 2

a–h Effect of independent variables on lightness (a, b), redness (c, d), yellowness (e, f), and water activity (g, h)

Effect on water activity (aw) and moisture content (MC)

The surface plots of aw and MC is shown in Figs. 2g, h and 3a, b, respectively. The aw varied significantly (P ˂ 0.05) from 0.75 to 0.21 with an increase in levels of independent variables. The highest aw was observed for T1 samples (0.75) when fried at 160 °C for 1 min and the lowest for T5 samples (0.21) when fried at 200 °C for 5 min. The T3, T4, and T5 samples fried at a temperature above 160 °C for at least 3 min showed aw lesser than 0.60, which suggested the safe zone for storage (Pongpichaiudom and Songsermpong 2018). The aw mostly depends on moisture distribution in the product, which reduces with an increase in frying time (Devi et al. 2020). A decrease in aw with increasing frying time and temperature was also reported by Yuksel et al. (2017) for deep-frying (170–190 °C, 40–60 s) of corn chips.

Fig. 3.

Fig. 3

a–f Effect of independent variables on moisture (a, b), total fat (c, d), and hardness (e, f)

The moisture loss was influenced by the variation in fat proportion. The increase in fat proportion (T1-T5) led to a reduction in MC in the range of 7.87–4.72% and 5.78–3.12% when fried at 160 °C and 180 °C, respectively, for a similar frying time of 4 min. The thickness of the dough layers decreased as the fat proportion increased, allowing for easier layer separation and a larger surface area (enhanced puffing) leading to higher moisture evaporation during the frying. Krokida et al. (2000) also reported that when the thickness of potato strips reduced, moisture loss increased. The MC also decreased with an increase in frying temperature and time. The MC was reduced to 1.40% when the frying temperature was increased to 200 °C, while it was 4.09% when the frying temperature was 160 °C for a similar frying time (5 min) for T5 sample. The highest moisture (14.41%) was found in the T1 sample when fried at 160 °C for 1 min. A similar effect of time and temperatures on MC was reported by Jumayi and Darwish (2021) for the frying of barley-soybean chips. Fikry et al. (2021) also reported a considerable change in MC for frying chickpea-based falafel.

Effect on total fat content

All the independent variables significantly (p < 0.05) affected the total fat content of Khaja samples (Table S2). The total fat content was highest (45.70%) for the T5 sample when fried at 200 °C for 5 min and lowest (25.05%) for the sample T1 when fried at 160 °C for 1 min. The total fat content of the samples increased significantly with an increase in fat proportion (T1-T5). The higher fat proportion increased the layer separation during frying resulting in exposure to a greater surface area and a significant replacement of water with oil. The thickness of dough layers decreased with increasing fat proportion, which might also result in higher absorption of oil, as reported in previous studies (Krokida et al. 2000; Gazmuri and Bouchon 2009). The mechanism of oil absorption can be described in two ways: oil absorption as part of replacement with evaporated water and absorption after the frying (Saguy and Dana, 2003). During moisture replacement, the development of pores allows oil to easily penetrate via empty spaces. Once the frying is completed, during cooling the oil adhered to the surface is drawn into due to the vacuum effect caused by a decrease in the internal vapor pressure (Moreira et al. 1997). The total fat content also increased significantly with an increase in the frying temperature and time as shown in Fig. 3c, d. The high temperature and time accelerate the evaporation of water, allowing more oil to be absorbed. The higher frying temperature is also associated with more tissue degradation and the generation of numerous pores, capillaries, and channels through which more oil is absorbed (Sobukola et al. 2013). Prakash et al. (2015) and Ghaderi et al. (2018) also observed similar effects for frying barley chips and potato strips, respectively.

Effect on textural property

The hardness of the samples reduced as the frying progressed, as indicated in Fig. 3e, f. The highest value (60.45 N) was observed for the T1 sample when fried at 160 °C for 1 min, which might be due to the insufficient heating of internal layers and development of a rubbery and chewie texture that required higher cutting force. The lowest value measured was 7.69 N for the T5 sample when fried at 190 °C for 5 min which could be the impact of high-temperature frying associated with rapid (explosive) evaporation, and resulted in more structural damage (Zhang et al. 2018). In addition, samples with low fat proportion were dense and compact, whereas samples with a high fat proportion had thinner dough layers, resulting in a crispier structure after frying. The increase in frying temperature and time allows sufficient moisture removal and the formation of a crisp structure, resulting in a lower hardness value. Chakkaravarthi et al. (2011) reported that a crisp texture in jilebi was observed when fried at 180 °C. Jumayi and Darwish (2021) also reported that increasing the frying temperature resulted in a decreased hardness value (p ˂ 0.05) for the frying of barley-soybean chips.

Correlation between variables

The Pearson’s correlation coefficient (r) is shown in Table 2 to provide a general statistical relationship between the dependent variables. Negative correlations are displayed in red and positive correlations in blue. The intensity of color indicated a measure of correlation, i.e., the stronger the correlation coefficient, the darker the color. The r values represent the linear correlation between the variables ranging from − 1 to + 1, with a negative number indicating that variable A decreases as variable B increases and a positive number indicating that variable A increases with variable B. There was a positive correlation of lightness with aw, MC and hardness. The lower the value of MC and aw, the darker sample was attained. With an increase in frying temperature and time, more water was evaporated from the samples, which accelerated the non-enzymatic browning reactions, and the lightness of samples decreased. A positive correlation was also observed between the MC and hardness, which might be explained as the immature frying of samples, and thus, hard (chewie) texture was obtained. Similar correlations were also found during deep-frying of gulabjamun balls (Kumar et al. 2006) and chhena jhilli (Mondal and Dash 2016). Besides, the MC also had a positive correlation with aw, and the redness had a positive correlation with the yellowness. However, MC had a negative correlation with the redness and yellowness. This showed that presence of low moisture during frying had darkened the color of the samples. A highly negative correlation existed between MC and total fat, which might be related to the fact that when moisture evaporates, various channels develop, which are subsequently filled by oil (Krokida et al. 2000; Nema and Prasad 2004).

Table 2.

Pearson’s correlation coefficient (r) between all variables

graphic file with name 13197_2022_5509_Tab2_HTML.jpg

Values marked with a star indicate significance at P < 0.05

Model description and sensory evaluation

The regression analysis was performed to check the suitability of models for various properties of fried Khaja. As shown in Table S3, the properties (lightness, redness, yellowness, aw, MC, and total fat content) of fried Khaja were linked to the linear, quadratic, and interaction terms of the fat proportion, frying temperatures, and time. The coefficient of determinations (R2) of the regression models for all variables (except yellowness, and hardness) varied between 91.87 and 95.33%. Some of the developed models can be used to navigate the design space for assurance of quality, thus may be used as predictive models. The R2 for yellowness and hardness was low and can only explain 78.49 and 71.76%, respectively, of all variance in the data.

The results of the sensory evaluation are presented in Table S5, which shows the various sensory attributes of fried and fried-sugar soaked Khaja samples. All the samples were found to have scored at least 6 in overall acceptability score, which could be an acceptable limit on a 9-point hedonic scale (Fikry et al. 2021). The color and taste score of the T4 samples fried at 180 °C, 4 min was not significantly different from the market sample. For the mouthfeel attribute, the highest score was observed for the market sample, followed by the T4 sample, fried at 180 °C for 4 min and 170 °C for 5 min. All the samples were significantly different in texture score except T4 samples when fried at 170 °C for 5 min and 180 °C for 4 min. The lowest texture score was given for the T3 sample fried at 170 °C for 5 min, which might be related to increased hardness due to inadequate layer separation caused by low fat proportion, as also revealed in the instrumental textural analysis. Among all the samples (except market sample) the maximum score for the overall acceptability was obtained for the T4 sample fried at 180 °C for 4 min. The validation of predicted values of responses obtained at optimum conditions is represented in Table S6. The predicted values showed a good agreement with the experimental and market sample data.

Microstructural changes in Khaja

The SEM micrograph of unfried and fried Khaja samples is shown in Fig. 4a–c. The surface morphology of un-fried samples (Fig. 4a) indicates the presence of uniform starch molecules with compact and smooth surfaces. Faster moisture loss and gelatinization of starch during high-temperature frying cause cell breakdown, resulting in larger pore size. The porous structure with larger cavities might have also resulted from a rapid expansion of water vapor during contact with the high oil temperature (Zhang et al. 2018). In addition to that, vaporization of water and penetration of oil led to the development of a high-pressure gradient that increased the size of the pores (Touffet et al. 2020). The market sample (Fig. 4b) showed a large amount of uneven breakage than the optimized sample (Fig. 4c), which could be due to frying at uncontrolled temperature leading to more damage to starch granules. Yang et al. (2020) reported a higher uneven surface morphology of potato sticks when the frying temperature was increased from 140 to 180 °C. Ghaitaranpour et al. (2018) reported a change in crust structures of doughnuts when the frying time was increased from 30 to 180 s. The microstructure of the food surface is known to change the oil absorption behavior which in turn can change the textural and sensory properties (Dehghannya and Ngadi 2021).

Fig. 4.

Fig. 4

Micrograph of unfried Khaja (a), Market Khaja (b), and optimized Khaja (c)

Fatty acid composition

The fatty acid compositions of the oil present in the market and optimized Khaja sample based on saturated and unsaturated fatty acids are shown in Table S7. The identification of fatty acid indicates the purity and quality of the oil since the type and quality of each fatty acid vary from one vegetable oil to another and also depends on processing conditions. The market Khaja sample was fried using palm oil, which has a higher amount of saturated fatty acid, while the optimized sample was fried in soyabean oil having lower saturated fatty acid. Trans fatty acids were not detected in both the samples, the presence of which may lead to various health disorders, including obesity, cardiovascular disease, diabetes, coronary artery disease, infertility, prostate and breast cancer (Islam et al. 2019). The market sample has the highest concentration of palmitic acid (46.79%) followed by cis-9 oleic acid (38.74%). The lowest concentration of saturated fatty acids was lauric acid (0.28%). The total saturated fatty acid (ΣSFA) was 14.54% higher than total unsaturated fatty acids (ΣUFA). Hegsted et al. (1993) suggested that higher saturated fatty acids raise the serum cholesterol while polyunsaturated fatty acids lower it.

The optimized Khaja sample showed the highest concentration of linoleic acid (51.65%) followed by cis-9 oleic acid (23.20%). The least amount of saturated fatty acid detected was myristic acid (0.14%). The ΣSFA was found to be 76.91% lower compared to ΣUFA. A higher level of linoleic and linolenic acid (Alpha and Gamma) was found, with 51.65 and 5.85%, respectively, which are considered essential fatty acids for growth, body maintenance, and physiological functions. Essential polyunsaturated fatty acids that are Omega-6 and Omega-3 fatty acids were also detected in the optimized sample, which is known to provide numerous positive health benefits such as lowering blood cholesterol, cardiovascular diseases, responsible for numerous cellular functions, maintaining the cell membrane structure, fluidity, signaling, and cell-to-cell interaction (Gammone et al. 2018). Since the saturated fatty acids are present in higher quantities in palm oil fried samples, soyabean oil may be considered as a better alternative frying medium.

Conclusion

This study used a comprehensive factorial experimental strategy to investigate changes in the quality characteristics of Khaja as influenced by the fat proportion, frying temperature, and time. The lightness, aw, MC, and hardness decreased significantly with increasing levels of independent parameters while redness, yellowness, and total fat content increased. The polynomial equations were also developed to predict the characteristics of fried Khaja in relation to independent variables. Sensory analysis was performed on the five most desirable samples, revealing that the sample with 20% fat proportion, fried at 180 °C for 4 min, had the highest overall acceptability score. These findings will assist in the standardization and control of the frying process to reduce the variation in the quality. Furthermore, relevant frying models can be used to understand the underlying mechanism and assist in optimizing processing parameters on a wide range of wheat flour-based fried snacks to meet quality standards.

Supplementary Information

Below is the link to the electronic supplementary material.

Acknowledgements

The authors would like to thank NIFTEM, India, an autonomous institute under the Ministry of Food Processing Industries (MOFPI), Government of India for infrastructural and financial support to conduct the present study.

Authors’ contributions

SK1 collected the experimental data, and drafted the manuscript. AC and SK2 did the formal analysis. PKN and VSSconceived and supervised the experimental analysis, interpretation of the data and drafted the manuscript. PG contributed to revising and writing a section of the manuscript. All authors reviewed and approved the manuscript.

Funding

The authors have not disclosed any funding.

Availability of data and material

All analyzed data during this study are included in this published article.

Declarations

Conflict of interest

Authors declare no conflict of interest.

Footnotes

Publisher's Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

References

  1. Chakkaravarthi A, Nagaprabha P, Kumar HNP, Latha RB, Bhattacharya S. Jilebi 3: effect of frying conditions on physical characteristics. J Food Sci Technol. 2011;51(5):865–874. doi: 10.1007/s13197-011-0595-6. [DOI] [PMC free article] [PubMed] [Google Scholar]
  2. Dana D, Saguy IS. Review: Mechanism of oil uptake during deep-fat frying and the surfactant effect-theory and myth. Adv Colloid Interface Sci. 2006;128:267–272. doi: 10.1016/j.cis.2006.11.013. [DOI] [PubMed] [Google Scholar]
  3. Dehghannya J, Ngadi M. Recent advances in microstructure characterization of fried foods: different frying techniques and process modeling. Trends Food Sci Technol. 2021;116:786–801. doi: 10.1016/j.tifs.2021.03.033. [DOI] [Google Scholar]
  4. Devi S, Zhang M, Ju R, Bhandari B. Water loss and partitioning of the oil fraction of mushroom chips using ultrasound-assisted vacuum frying. Food Biosci. 2020;38:100753. doi: 10.1016/j.fbio.2020.100753. [DOI] [Google Scholar]
  5. Fellows PJ. Food processing technology, principles and practice. 3. England: Woodhead publishing limited; 2017. Frying; pp. 555–573. [Google Scholar]
  6. Fikry M, Khalifa I, Sami R, Khojah E, Ismail KA, Dabbour M. Optimization of the frying temperature and time for preparation of healthy falafel using air frying technology. Foods. 2021;10(11):2567. doi: 10.3390/foods10112567. [DOI] [PMC free article] [PubMed] [Google Scholar]
  7. Gammone MA, Riccioni G, Parrinello G, D’Orazio N. Omega-3 polyunsaturated fatty acids: benefits and endpoints in sport. Nutrients. 2018;11(1):46. doi: 10.3390/nu11010046. [DOI] [PMC free article] [PubMed] [Google Scholar]
  8. Gazmuri AM, Bouchon P. Analysis of wheat gluten and starch matrices during deep-fat frying. Food Chem. 2009;115(3):999–1005. doi: 10.1016/j.foodchem.2009.01.020. [DOI] [Google Scholar]
  9. Ghaderi A, Dehghannya J, Ghanbarzadeh B. Momentum, heat and mass transfer enhancement during deep-fat frying process of potato strips: influence of convective oil temperature. Int J Therm Sci. 2018;134:485–499. doi: 10.1016/j.ijthermalsci.2018.08.035. [DOI] [Google Scholar]
  10. Ghaitaranpour A, Koocheki A, Mohebbi M, Ngadi MO. Effect of deep fat and hot air frying on doughnuts physical properties and kinetic of crust formation. J Cereal Sci. 2018;83:25–31. doi: 10.1016/j.jcs.2018.07.006. [DOI] [Google Scholar]
  11. Hegsted DM, Ausman LM, Johnson JA, Dallal GE. Dietary fat and serum lipids: an evaluation of the experimental data. Am J Clin Nutrit. 1993;57(6):875–883. doi: 10.1093/ajcn/57.6.875. [DOI] [PubMed] [Google Scholar]
  12. Islam MA, Amin MN, Siddiqui SA, Hossain MP, Sultana F, Kabir MR. Trans fatty acids and lipid profile: a serious risk factor to cardiovascular disease, cancer and diabetes. Diabetes Metab Syndr. 2019;13(2):1643–1647. doi: 10.1016/j.dsx.2019.03.033. [DOI] [PubMed] [Google Scholar]
  13. Jumayi AA, Darwish AM. Frying time and temperature conditions’ influences on physicochemical, texture, and sensorial quality parameters of barley-soybean chips. J Food Qual. 2021 doi: 10.1155/2021/5748495. [DOI] [Google Scholar]
  14. Krokida MK, Oreopoulou V, Maroulis ZB. Water loss and oil uptake as a function of frying time. J Food Eng. 2000;44(1):39–46. doi: 10.1016/S0260-8774(99)00163-6. [DOI] [Google Scholar]
  15. Kumar AJ, Singh RRB, Patel AA, Patil GR. Kinetics of colour and texture changes in Gulabjamun balls during deep-fat frying. LWT Food Sci Technol. 2006;39(7):827–833. doi: 10.1016/j.lwt.2005.05.016. [DOI] [Google Scholar]
  16. Mondal IH, Dash KK. Textural, color kinetics, and heat and mass transfer modeling during deep fat frying of Chhena Jhili. J Food Process Preserv. 2016;41(2):e12828. doi: 10.1111/jfpp.12828. [DOI] [Google Scholar]
  17. Moreira RG, Sun X, Chen Y. Factors affecting oil uptake in tortilla chips in deep-fat frying. J Food Eng. 1997;31(4):485–498. doi: 10.1016/S0260-8774(96)00088-X. [DOI] [Google Scholar]
  18. Nema PK, Prasad S. Effects of frying oil temperature on quality and yield of potato chips. J Food Sci Technol. 2004;41(4):448–450. [Google Scholar]
  19. Nsabimana P, Powers JR, Chew B, Mattinson S, Baik BK. Effects of deep-fat frying temperature on antioxidant properties of whole wheat doughnuts. Int J Food Sci Technol. 2018;53(3):665–675. doi: 10.1111/ijfs.13641. [DOI] [Google Scholar]
  20. Omidiran AT, Sobukola OP, Sanni SA, Sanni LO, Adebowale AA, Shajobi AO, Kulakow P. Evaluation of some quality parameters of cassava starch and soy protein isolate matrices during deep fat frying in soybean oil. Food Sci Nutr. 2019;7(2):656–666. doi: 10.1002/fsn3.904. [DOI] [PMC free article] [PubMed] [Google Scholar]
  21. Pongpichaiudom A, Songsermpong S. Characterization of frying, microwave-drying, infrared-drying, and hot-air drying on protein-enriched, instant noodle microstructure, and qualities. J Food Process Preserv. 2018;42(3):e13560. doi: 10.1111/jfpp.13560. [DOI] [Google Scholar]
  22. Prakash J, Naik HR, Hussain SZ, Singh B. Effect of processing conditions on the quality characteristics of barley chips. J Food Sci Technol. 2015;52(1):294–302. doi: 10.1007/s13197-013-0997-8. [DOI] [PMC free article] [PubMed] [Google Scholar]
  23. Reddy US (2018) Bihar’s sweet delicacy Silao Khaja gets GI tag. https://timesofindia.indiatimes.com/city/patna/bihars-sweet-delicacy-silao-khaja-gets-gi-tag/articleshow/67116955.cms. Accessed 25 Sept 2021
  24. Saguy IS, Dana D. Integrated approach to deep fat frying: engineering, nutrition, health and consumer aspects. J Food Eng. 2003;56(2–3):143–152. doi: 10.1016/S0260-8774(02)00243-1. [DOI] [Google Scholar]
  25. Sobukola OP, Dueik V, Munoz L, Bouchon P. Comparison of vacuum and atmospheric deep-fat frying of wheat starch and gluten-based snacks. Food Technol Biotechnol. 2013;22(1):177–182. doi: 10.1007/s10068-013-0064-2. [DOI] [Google Scholar]
  26. Touffet M, Trystram G, Vitrac O. Revisiting the mechanisms of oil uptake during deep-frying. Food Bioprod Process. 2020;123:14–30. doi: 10.1016/j.fbp.2020.06.007. [DOI] [Google Scholar]
  27. Xu Z, Leong SY, Farid M, Silcock P, Bremer P, Oey I. Understanding the frying process of plant-based foods pretreated with pulsed electric fields using frying models. Foods. 2020;9(7):949. doi: 10.3390/foods9070949. [DOI] [PMC free article] [PubMed] [Google Scholar]
  28. Yang D, Wu G, Li P, Qi X, Zhang H, Wang X, Jin Q. The effect of fatty acid composition on the oil absorption behavior and surface morphology of fried potato sticks via LF-NMR, MRI, and SEM. Food Chem X. 2020;7:100095. doi: 10.1016/j.fochx.2020.100095. [DOI] [PMC free article] [PubMed] [Google Scholar]
  29. Yuksel F, Karaman S, Gurbuz M, Hayta M, Yalcin H, Dogan M, Kayacier A. Production of deep-fried corn chips using stale bread powder: effect of frying time, temperature and concentration. LWT. 2017;83:235–242. doi: 10.1016/j.lwt.2017.04.076. [DOI] [Google Scholar]
  30. Zhang Y, Zhang T, Fan D, Li J, Fan L. The description of oil absorption behavior of potato chips during the frying. LWT. 2018;96:119–126. doi: 10.1016/j.lwt.2018.04.094. [DOI] [Google Scholar]

Associated Data

This section collects any data citations, data availability statements, or supplementary materials included in this article.

Supplementary Materials

Data Availability Statement

All analyzed data during this study are included in this published article.


Articles from Journal of Food Science and Technology are provided here courtesy of Springer

RESOURCES