Abstract
Thermal Magnetic Resonance (ThermalMR) integrates Magnetic Resonance Imaging (MRI) diagnostics and targeted radio-frequency (RF) heating in a single theranostic device. The requirements for MRI (magnetic field) and targeted RF heating (electric field) govern the design of ThermalMR applicators. We hypothesize that helmet RF applicators (HPA) improve the efficacy of ThermalMR of brain tumors versus an annular phased RF array (APA). An HPA was designed using eight broadband self-grounded bow-tie (SGBT) antennae plus two SGBTs placed on top of the head. An APA of 10 equally spaced SGBTs was used as a reference. Electromagnetic field (EMF) simulations were performed for a test object (phantom) and a human head model. For a clinical scenario, the head model was modified with a tumor volume obtained from a patient with glioblastoma multiforme. To assess performance, we introduced multi-target evaluation (MTE) to ensure whole-brain slice accessibility. We implemented time multiplexed vector field shaping to optimize RF excitation. Our EMF and temperature simulations demonstrate that the HPA improves performance criteria critical to MRI and enhances targeted RF and temperature focusing versus the APA. Our findings are a foundation for the experimental implementation and application of a HPA en route to ThermalMR of brain tumors.
Keywords: brain tumor, glioblastoma multiforme, theranostics, temperature, hyperthermia, MRI, Thermal Magnetic Resonance, RF transmitter array, helmet RF phased array, multi-target evaluation approach
1. Introduction
Localized hyperthermia (HT, temperature range T = 39–44 °C for 60–90 min) is used as a thermal adjunct therapy that has been proven to enhance chemo-, radio- or immunotherapy to inhibit tumor growth and improve the efficacy of the clinical outcome [1,2]. Thermal therapy has seen a revival for the treatment of glioblastoma multiforme (GBM), which is the most frequent and aggressive malignant brain tumor, comprising more than 60% of all brain tumors [3] and with a mean survival time of approximately 14 to 15 months from diagnosis [4]. Targeted radiofrequency (RF)-induced heating is a specific variant of thermal therapy [2,5] considered for glioblastoma therapy. Notwithstanding the clinical benefits, standalone HT approaches lack inherent in vivo diagnostic imaging, non-invasive temperature mapping, and therapy detection capabilities [1,6,7]. Any in vivo HT modality would greatly benefit from diagnostic guidance, temperature dosimetry, and the capacity to monitor therapy outcomes, which is facilitated by non-invasive imaging [8,9]. This is especially crucial for GBM thermal therapy planning and monitoring because of the constraints provided by the skull, and the very sensitive nature of the central nervous system [10].
Magnetic resonance imaging (MRI) is a mainstay of diagnostic imaging. It offers exquisite spatial resolution and soft tissue contrast for anatomical reference. MRI provides intrinsic contrast mechanisms for functional and physiological assessment. Moreover, MRI facilitates non-invasive temperature cartography to support HT therapy planning and monitoring [11,12,13,14]. This makes it conceptually appealing to synergistically connect MRI and HT in a multi-modality approach. Current MRI-HT hybrid implementations commonly employ two RF sub-systems that are controlled and operated independently [15,16]. This approach requires extra RF hardware and is not cost-effective. The risk of mutual interferences between the two RF chains is a weakness of the multi-modality hybrid approach. This approach may induce compatibility issues and practical obstacles for the system’s integration because each sub-device is typically provided by different vendors.
An instrument that truly integrates diagnostic guidance, thermal treatment, and therapy monitoring can help better define the role of temperature in biological systems and disease and use these insights for enhanced thermal therapies. Thermal Magnetic Resonance (ThermalMR) adds a thermal intervention dimension to a MRI device. It integrates RF-induced heating, in vivo non-invasive temperature mapping, and diagnostic MRI in a single, multi-purpose RF applicator including a phased array of RF transmitters [17]. ThermalMR is facilitated by the two orthogonal and complementary components of electromagnetic fields. RF transmission and reception used for MRI rely on magnetic fields (H-field) perpendicular to the main static magnetic field (B0) of a MR scanner. RF heating builds on electric fields (E-field). Constructive interference of E-fields produced by multiple RF sources can be used for targeted focal RF heating. These requirements govern the design of multi-purpose RF applicators tailored for ThermalMR.
MR instruments operating at ultrahigh magnetic field strengths (UHF, B0 ≥ 7.0 T) [18] use higher operating frequencies than conventional clinical MRI systems. While the long electromagnetic wavelength in tissue at 64 MHz (1.5 T, commonly used for clinical MRI) is not suitable to focus electromagnetic (EM) energy within small target volumes, the shortened wavelength in tissue at ≥297 MHz (≥7.0 T) enables stronger focusing of RF fields due to more localized interference patterns. This phenomenon offers the potential to provide focal temperature increase, offering ample opportunity for ThermalMR theranostics.
Ensuring a patient and case-specific adaptation of the size, uniformity, and location of the RF energy deposition in the treatment target volume is of the essence for developing ThermalMR theranostics for brain tumors [10,19,20,21]. The focal point quality is governed by the radiation pattern of the single RF transmit element [22,23,24,25,26], the thermal intervention frequency of the RF applicator, the RF channel count, and the geometric arrangement of the transmit elements in a phased array. The potential of high-density phased arrays for ThermalMR RF applicators is well recognized [10,17,19,25,27,28]. Increasing the number of RF transmission elements per unit area increases the degrees of freedom (amplitude and phase) and enhances the focal point quality and RF peak power deposition for thermal therapy. It also enables improvements in the transmission field (B1+) efficiency and uniformity of MRI. Considering the limited amount and costs of RF amplifiers of commercially available MRI systems which typically feature 8TX channels, distributing a limited number of RF transmission elements around the head presents an alternative to increasing the number of RF transmission elements.
Pioneering reports on the ultimate intrinsic signal-to-noise ratio (SNR) in MRI and ultimate intrinsic specific absorption rate (SAR) suggested that RF transmit antenna arrangement and positioning also influences MR image quality in UHF-MR, as well as the focal point quality of thermal interventions [29,30]. This is especially relevant for ThermalMR of deep-seated brain tumors. The head presents a small surface area that constrains the number of RF transmission elements that can be arranged in an array to cover the head. Multi-channel transmit RF arrays tailored for whole brain MRI or HT of the head are commonly designed with loop or dipole antennas [10,21,28,31], or combinations of both loop and dipole antennas [22,32,33,34]. Dome-shaped helmet RF applicator configurations provide a viable alternative for MRI or HT [21,25,31,35,36,37]. However, the dome-shaped RF arrays previously published did not incorporate transmission elements positioned perpendicular to either the cranial–caudal axis of the body or the main magnetic field of an MR scanner. The applicability and performance of this approach for ThermalMR have not yet been explored. The conventional antenna phased arrays (APAs) utilized in current applications feature a singular row of elements. Our research diverges from this standard by not simply adding more elements or rows to increase complexity. Instead, we present a strategy that retains the simplicity inherent in most MRI-guided hyperthermia (MRI-HT) applicators. We achieve this by reconfiguring the APA into a helmet-like array, offering a novel approach that differs significantly from methods discussed in the existing literature. This allows for enhanced functionality without complicating the array structure, aligning with our goal of improving treatment efficacy while maintaining device simplicity.
Recognizing this opportunity, we hypothesize that dome-shaped helmet RF applicators improve the efficacy of ThermalMR theranostics by providing enhanced mean B1+ uniformity for brain MRI at 7.0 T and by enabling enhanced focal point quality for RF-induced heating of brain tumors versus an annular RF array using the same number of transmit RF elements. To test this hypothesis, this work examines the feasibility and benefits of a helmet ThermalMR applicator comprising eight broadband self-grounded bow-tie (SGBT) antennae [24,38,39] arranged in an annular phased array around the head in conjunction with two SGBT antennae placed on top of the head perpendicular to B0. For benchmarking, an annular ThermalMR applicator comprised of 10 equidistantly placed transmit SGBT elements is used as a reference. To assess the ThermalMR applicators, we first used the conventional approach of targeting a few very specific but arbitrary areas of the brain. Recognizing that this approach does not represent the full clinical picture we expanded the evaluation to whole-brain slice coverage. For this purpose, we introduce a multi-target evaluation (MTE) framework.
2. Materials and Methods
2.1. RF Applicator Design
2.1.1. MRI Considerations
For diagnostic MRI, transmission field (B1+, B1+ = (Bx + iBy)/2 efficiency, and B1+ homogeneity are critical criteria for RF array design (Figure 1) [40]. RF elements used for MRI should induce an H-field (H~ B1+) perpendicular to the main static magnetic field B0,z. Considering that only Bxy components contribute to B1+, appropriate RF element arrangement is critical for MRI. Using a multi-channel array of RF elements enhances B1+ uniformity in the target region while staying within the SAR (W/kg) limits of MRI [40,41,42].
2.1.2. RF Heating Considerations
RF heating builds on E-fields and depends on the extent of energy absorption in tissue, which is described by the SAR or Power Loss Density (PLD) in W/m3. Thermal dosage is the integral of SAR over time [43]. In HT, a SAR-induced temperature increase is used to heat the target region between T = 39 and 44 °C while preserving surrounding healthy tissues (T < 41 °C) and maintaining a safe margin [44] between the target region and healthy tissue (Figure 1).
These requirements for MRI and RF heating govern the design of RF applicators tailored for ThermalMR.
2.1.3. RF Antenna Building Block
A broadband SGBT antenna [45] (Figure 2a, frequency range: 230–560 MHz, size: 42.3 × 46.3 × 20 mm3, antenna: 0.3 mm copper, substrate: 0.5 mm FR4) was used as an RF building block for modeling transmission (TX) of electromagnetic waves [24]. For wavelength shortening, the SGBT was placed in a housing (Nylon 12, 114.4 × 54 × 22.5 mm3) filled with D2O (ε = 81 at 297.2 MHz to reduce antenna size) [24]. D2O was used because the MRI resonance frequency is outside of the bandwidth of the SGBT antenna. Hence, the SGBT building block does not contribute to the MR signal, which H2O would otherwise do. In this work, the xyz-coordinate system describes the orientation of the MR scanner and of the object under investigation (OUI). The uvw-coordinate system describes the orientation of the SGBT which is shown in Figure 2. Considering the defined uvw-coordinate system and microscopic Maxwell’s equations for propagating electromagnetic plane waves, SGBTs generate an E-field (V/m) in the ±w-axis direction and an H-field (A/m) perpendicular to the E-field (S = E × H, where S is the Poynting vector in the direction of propagation [46]) and the propagation direction in the far-field (Fraunhofer Distance) of antenna (>2 D2/ when D (√(42.32 × 46.32 × 202) = 65.8 mm) is the maximum dimension of the antenna profile) [24,47,48]. At 297.2 MHz, the wavelength inside the D2O-filled antenna building block is λc = 113.9 mm, so the far-field starts at distances >76.7 mm. Figure 2 shows the H-field vector pattern of an SGBT building block for four arrangements on the human head. Configurations shown in Figure 2b–d provide H-fields perpendicular to B0. For example, an SGBT antenna placed perpendicular to B0 (w-axis parallel to z-axis) with the long axis aligned with the anterior-posterior (y-axis) direction generates an H-field perpendicular to B0 (Figure 2b). When placing the SGBT on top of the head with the vw-plane parallel to the xy-plane and the w-axis parallel to the y-axis (Figure 2c) or the w-axis parallel to the x-axis (Figure 2d), H-fields are generated in the x-direction and y-direction, which are perpendicular to B0. The configuration with the w-axis of the SGBT aligned with the y-direction (Figure 2c) provides better coverage along the long axis of the head than the configuration, where the w-axis of the SGBT is aligned with the x-axis (Figure 2d). Therefore, the former was used for further examination. If the SGBT antenna is rotated 90° around its u-axis and aligned with the v-axis parallel to the z-axis, the induced H-fields are produced in the z-direction parallel to B0 (Figure 2e). The latter setup represents the “dark MRI mode” and is excluded from further considerations since it does not provide an H-field perpendicular to B0 [49].
2.1.4. RF Phased Array
For the design of the RF applicator array, the inter-element distance was considered first in order to prevent creating grating lobes (GLs). GLs have much higher intensity than side lobes, which can lead to severe power losses. The RF antenna array’s radiation pattern can be calculated through [50,51]:
(1) |
where n is the number of grating lobes (n = 0 is the main lobe), and d is the inter-element distance. According to Equation (1), the inter-element distance should be . Considering the inter-element distance requirements and the size of an average human head, two RF applicators, each comprising ten RF building blocks (Figure 2), were designed:
Annular Phased RF array (APA, Figure 2g): Ten SGBT RF building blocks were placed equidistantly in a single-row annular array where the w-axis of the SGBT elements is aligned with the z-axis of the main magnetic field B0.
Helmet Phased RF array (HPA, Figure 2f): Eight SGBT RF building blocks shown in Figure 2b were arranged equidistantly in a single-row annular array. Two SGBT RF building blocks, shown in Figure 2c, were placed on top of an eight-elements APA. This approach takes the elliptical shape of the human head into account and aligns the long axis of the SGBT with the longest axis of the head for the benefit of better head/brain coverage.
The shortest inter-element distance between the feeding points of adjacent RF building blocks is 83 mm for the APA and 105 mm for the annular ring of the HPA. A water bolus filled with deionized water (H2O) (T = 21 °C) was placed between the RF building blocks and the OUI for antenna matching and surface cooling.
2.2. Numerical Simulations
2.2.1. EMF Simulations
For the design and the assessment of the two RF applicator configurations, EMF simulations were performed using two commercial software packages:
CST Microwave Studio Suite 2020 (Dassault Systèmes, Darmstadt, Germany) [10,52]: EMF simulations were performed using broadband excitation (f = 297.2 ± 50 MHz) and the time-domain solver based on the finite integration technique (FIT) mesh size of 1.75 mm × 1.75 mm × 1.75 mm was used for the antenna. EMF simulations were applied to the human head voxel model Duke of the virtual family truncated at the level of the neck (IT’IS Foundation, Zurich, Switzerland [53]) (resolution of 1.0 × 1.0 × 1.0 mm3) and placed at the isocenter of a RF shield model of the bore of a 7.0 T MRI system. For the human voxel model, SAR10g (SAR calculations were averaged over 10 g of tissue or phantom material (SAR10g)) was evaluated for cuboid target regions (TR). For this purpose, four TR sizes with a main target region (mm3) and a gap between the target margin and safety margin (mm3) were defined: TR1 = 87.5 mm × 87.5 mm × 4 mm (22 mm), TR2 = 62.5 mm × 62.5 mm × 4 mm (10 mm); TR3 = 37.5 mm × 37.5 mm × 4 mm (10 mm); TR4 = 15 mm × 15 mm × 4 mm (10 mm). The cuboid TRs were chosen over cylindrical or spherical TRs to make the TR more tumor shaped, unpredictable, with some corners, independent from the symmetric applicator arrangement of a circular array, and more challenging than a cylindrical TR. To examine the homogeneity of SAR10g, the metric target coverage (TC) describes the target volume that covers xx% (xx = 25, 50, and 75) of the maximum SAR10g (SAR10g,max) inside the TR.
Sim4Life Version 7.0.2 (Zurich Med Tech, Zurich, Switzerland). The Electromagnetics Full Wave Solvers finite-difference time-domain (P-EM-FDTD) was used for EM modeling (f = 297.2 ± 50 MHz). Thermodynamic Solvers (P-THERMAL) based on FDTD and a steady-state finite volume were used for advanced perfusion and thermoregulation modeling. The P-Thermal solver utilizes the Poisson differential equation to model heat transfer in living tissue, accommodating a range of adaptable boundary conditions. The transient thermal solver assumes a dynamic state where all tissue domains possess non-zero thermal conductivity or heat transfer rates. This software package supports the import of segmented real-world data obtained from computed tomography (CT) or MRI into a human voxel model. It also provides a comprehensive library of thermal and electrical tissue properties for a human model. For the simulations, clinical tumor geometry data obtained from a GBM patient were integrated into the human voxel model truncated at the level of the neck. For this purpose, a CT scan of a GBM patient was imported into Sim4Life [10]. Dielectric and thermal properties of up to 20 labeled tissue [10] used for radiotherapy planning including the GBM (volume = 172 mL, σ = 1.15 S/m, ε = 66.5 [54]) were assigned to the head geometry of the patient (headmass = 3.68 kg). Adding the cerebrospinal fluid (CSF) layer was accomplished by upscaling the brain by 5% [10]. The excitation center frequency and bandwidth were set to 297.2 ± 50 MHz. The mesh size, regarding the voxel shaping of the antenna in Sim4Life was limited to a maximum step size of 3 mm within the skull and 5 mm within the lower region of the modified human head voxel model. A much finer resolution of down to 0.1 mm was applied to the feeding points to resolve the triangular shape of the SGBT.
2.2.2. Temperature Simulations
Temperature simulations were performed with Sim4Life using the Pennes bioheat transfer equation including tissue perfusion with a thermal simulation time of t = 3600 s [55,56].
In the Pennes bioheat transfer equation heat exchange mechanisms, including heat conduction, blood perfusion, and resistive heating are considered, as follows [57]:
(2) |
where the position vectors of tissue and time are denoted by r and t, respectively, and the temperatures of tissue and blood are T and TB (°C), respectively. C (J/°C/kg) is the specific heat of tissue, K (W/°C/m) is the thermal conductivity of the tissue, ρ (kg/m3) is mass density; and A (r, t) is the heat generated by metabolism. The initial temperature of the water bolus was fixed at T = 21 °C. The initial body temperature was set to T = 37 °C [58]. Subsequently, the transient heating phase was evaluated for an intervention period of 3600 s using the thermal transient solver considering the thermal boundaries of the European Society for Hyperthermic Oncology (ESHO) guidelines [54]. To simulate the effect of RF heating, the temperature was calculated from the previously calculated power loss density W/cm3 (local SAR10g) based on the Pennes bioheat equation. Temperature-dependent thermal properties using the thermal stress model based on the ESHO benchmarks were assigned to the patient head voxel model. The blood perfusion rate under thermal stress is different for fat, muscle, tumor, and skin considering the tumor is typically inhomogenous, well perfused in the periphery, and necrotic in the core (due to lack of blood perfusion). For instance, this value increases from 0.7 to 3.6 in muscle [54]. For the HT optimizer tool of Sim4Life [59], clinical TV (CTV) and gross TV (GTV) were chosen as target tissues. The loss-free power received in the tumor was defined as 11 W per RF channel inside the tumor to reach a maximum of about 45 °C in the tumor. Cumulative histograms of 10%, 50%, and 90% of the masked target region (here CTV) covered by a minimum temperature are given by T10, T50, and T90 (°C).
2.3. RF Circuit Co-Simulation
While a SGBT exhibits a broadband frequency response, its implementation in a phased array design with multiple antennas in APA and HPA introduces coupling effects that can impact its frequency response. By adding a lossy L-series and a C-parallel circuit in Matlab 2021a (Mathworks, Natick, MA, USA), co-simulations for frequency tuning and impedance matching of each of the 10-element RF arrays were performed to ensure Sii (return loss) and Sij (mutual coupling) of <−10 dB for all RF elements [50]. The evaluation of estimated losses involved analyzing the equivalent series resistance of capacitors with data sourced from non-magnetic ceramic capacitors (ATC100C, American Technical Ceramics, NY, USA). Inductor losses were taken into consideration by using the Q-factor, referring to the database for non-magnetic air-coil inductors (1512SP, Coilcraft Inc., Cary, IL, USA). Subsequently, the results from electromagnetic field simulations, coupled with material/tissue properties, were utilized in post-processing (Matlab) to calculate distributions of B1+ and SAR10g,max, achieving an isotropic resolution of 4.0 × 4.0 × 4.0 mm3. The −10 dB bandwidth (Δf|Sii<−10) is calculated for both phased arrays.
2.4. Electromagnetic Field Shaping
2.4.1. Transmission Field Shimming for MRI
To enhance B1+ transmission efficiency and uniformity over the entire brain and to manage RF safety, transmission field shimming was performed. For this purpose, a genetic optimization algorithm [60] was used in conjunction with unconstrained minimization (fminunc) [61], which was implemented in the global optimization toolbox of Matlab. B1+ shimming was applied with three objectives: (i) maximizing minimum B1+ inside the full ROI; (ii) minimizing the standard deviation (SD) of B1+ divided by the mean value defining the Coefficient of Variation of B1+ (CoV = SD/mean); and (iii) maximizing mean B1+ in the brain ROI [62]. For this purpose, two parallel transmission regimes were used including (i) phase B1+ shimming (PS) and (ii) amplitude and phase B1+ shimming (APS) [54].
2.4.2. RF Excitation Vector Optimization for RF Heating and Hyperthermia Treatment Planning
Optimization algorithms are employed to determine optimal excitation vectors for RF coil arrays, ensuring precise and safe heating [63]. For thermal intervention, RF phase and amplitude configurations were determined (independent from the RF phase and amplitude setting used for MRI) by the product of the eigenvector and the square root of its eigenvalue. For excitation vector optimization time multiplexed vector field shaping (MVFS) was implemented [64]. MVFS automatically selects the appropriate time-interleaved excitations. The resulting SAR distribution of the incident electric field interference is tailored to focus the heating of the TR while minimizing local peak RF exposure to healthy and remote tissue below a defined threshold. Finding appropriate constraints to reach temperature target values is essential in this work to reach HT temperature target values in the TR. There is no exact SAR value to reach the HT temperature since the temperature is dependent on many factors in human tissue. Based on the Pennes bioheat equation and using the simplified heat equation SAR = CΔT/Δt (C is the heat capacity in J/°C/kg, cbrain = 3452 J/°C/kg) as an approximation, a temperature increase of 1 °C in 1 min in brain tissue requires a minimum average SAR10g of ~60 W/kg [55]. Following this consideration, SAR10g was set to 40 W/kg < SAR10g < 80 W/kg for the TR to ensure that the target temperature is accomplished in most of the TR. This SAR10g range can be defined as a 0.7 °C < ΔT < 1.4 °C temperature increase in 1 min. For healthy tissues, SAR10g was conservatively limited to <40 W/kg. A safety margin was defined for which SAR10g was not constrained.
2.5. Evaluation and Benchmarking
2.5.1. MRI
To assess the performance of the RF applicators for MRI, the transmit performance was evaluated for the phantom and for the voxel model of the human head [65,66].
B1+ superposition:
The evaluation of RF array transmit efficiency necessitates the use of B1+ amplitudes, as well as the power correlation matrix for each RF channel [65]. For the B1+ superposition approach, two models accounting for (i) only sample losses (ideal model, IM), and for (ii) sample, coil, and coupling losses (realistic model, RM) were investigated and rescaled to match a total incident power of 1 W (B1+/√1 W (B1+,eff [µT/√W]).
Field shaping for static parallel transmission (pTX):
The B1+ maps obtained from the optimization process for B1+ were rescaled to match a total incident power of 1 kW, which is denoted as B1+ efficiency (B1+/√1 kW (B1+,eff [µT/√kW]), where B1+ efficiency represents the ratio of B1+ field strength to the square root of 1 kW.
Minimum B1+ optimization:
In order to prevent B1+ signal dropouts, the objective was to maximize the lowest value of the combined B1+ field from each individual RF channel over the ROI that encompasses the entire test object or the brain. This was achieved by optimizing the target function of minimum B1+ [67].
(3) |
where Nch represents the count of channels, represents the complex transmission field unique to each RF channel within the 3D ROI, and Exch denotes the complex excitation vector used for Nch channels [67].
Coefficient of variation optimization:
The coefficient of variation reflects the degree of (non)uniformity of the B1+ distribution. In order to reduce the coefficient of variation (CoV, calculated as the standard deviation divided by the mean) over the entire 3D ROI that encompasses the test object or the brain, the following target function was employed [67]:
(4) |
Mean B1+ optimization
In order to increase the signal, the objective was to maximize the mean value of the combined B1+ field from each individual RF channel over the ROI that encompasses the entire test object or the brain. This was achieved by optimizing the target function of minimum B1+ [67].
(5) |
SAR optimization with MRI considerations:
SAR10g is another metric for MRI assessment which should stay within the safety limits for the head (3.2 W/kg for 6 min duration) governed by the IEC guidelines [68]. To assess MR safety the metric SAR10g,WCS (SAR10g, Worst Case Scenario [69]) was used. To obtain SAR10g,WCS maximum |E|2 was determined for all possible B1+ input complex values for each pixel obtained for the APS and PS parallel transmission (pTX) B1+ shimming approaches [69].
2.5.2. Quality of Targeted RF Heating
For the assessment of the targeted RF, heating SAR-based metrics defined by the ESHO were applied [54]. For further evaluation, we introduced new SAR10g-based homogeneity indicators for healthy brain tissues. The input power was scaled until reaching a maximum SAR10g limit of 40 W/kg in healthy tissue. Table 1 surveys the definition and a brief description of all metrics included in the evaluation of the quality of targeted RF heating of the two RF applicator configurations. To examine the quality of the RF heating, we used TCxx as a uniformity factor, which describes the volume that covers xx% (xx = 25, 50, and 75) of the SAR10g,max inside the TR.
Table 1.
Indicator | Location | Description | Unit | Valid Value | Equation |
---|---|---|---|---|---|
SAR10g | Whole Head | SAR10g averaging over cubes covering 10 g of tissue (SAR10g) distributions inside the human head voxel model Duke ; σ (S/m) is the electrical conductivity, ρ (kg/cm3) is the mass density, and |E| (V/m) is the magnitude of the local electric field vector |
W/kg | <40 (HR) | (6) |
<80 >40 (TR) | |||||
TCxx (TC25/TC50/TC75) [70,71,72] | TR | Measures the percentage of volume with SAR10g over 25% (TC25), 50% (TC50) or 75% (TC75) of SAR10g,max found in the TR. This is only evaluated if SAR10g,max >40 W/kg. |
% | >75 [54] | (7) |
* Off-TCxx (off-TC25/off-TC50/off-TC75) | HR | iso-SAR contour in healthy tissue defined as off-target regions (off-TR). Measures the percentage of voxels in the HR with SAR10g over the (25%, 50%, and 70%) of the SAR10g,max found in HR (healthy constraint SAR10g (40 W/kg))). |
% | (8) | |
SAR10g Amplification Factor (SAF) [10,70,73] | Whole Head | Measures that healthy tissue preservation from mean SAR10g in HR |
- | (9) | |
Homogeneity Coefficient (HC) [70] | TR | Measures how homogenous the SAR10g,max is distributed over TR | - | ||
- | (10) | ||||
* Homogeneity Coefficient (off-HC) | HR | Measures how homogenous the SAR10g,max in healthy tissue is distributed over HV. | - | ||
- | (11) | ||||
* Total Homogeneity
Coefficient (THC) |
Whole Head | Measures total homogeneity of SAR10g inside the TR and HR to satisfy hyperthermia treatment goals | - | ||
- | (12) | ||||
Performance Indicator (PI) [72] | Whole Head | Measures the total performance of each hyperthermia treatment planning | - | ||
W/kg | (13) | ||||
Txx (T10/T50/T90) [54,72] | TR | In clinical practice, the assessment of tumor coverage should involve the examination of indexed temperatures, specifically T10, T50, and T90. These values correspond to the temperatures reached in at least 10%, 50%, and 90% of the target region, respectively. | °C | T50 > 40 | (14) |
* These indicators are defined for this work.
2.5.3. Multi-Target Evaluation
Assessment of RF building blocks and ThermalMR phased array applicators commonly uses target region locations covering a few very specific but arbitrary target regions of the brain. Tissue properties inside the human brain exhibit spatial differences, so TRs including tissue with higher conductivity (for example, CSF) can lead to higher SAR10g. Following this conventional approach, we placed TR3 = 37.5 mm × 37.5 mm × 4 mm (10 mm)) into four arbitrary but specific target regions.
(location L1–L4) placed in the (i) limbic lobe and postcentral gyrus (L1), (ii) the Thalamus region (L2), (iii) the corpus callosum and limbic lobe (L3), and (iv) the parietal lobe (L4) of the brain. Remote, healthy brain tissue was also included in the assessment. However, using a limited number of arbitrary tumor locations in the brain does not represent the full clinical picture. To address this shortcoming, we expanded the evaluation from a limited number of arbitrary tumor locations to whole brain slice coverage. For this reason, we introduced a multi-target evaluation (MTE) framework (Figure 3). For this purpose, numerical simulations moving hypothetical TRs throughout the entire brain (Figure 3, Supplementary Video S1) were conducted (step size = 7 mm, total number of locations = 26 × 27 = 702) for 4 TR sizes: TR1 = 30.625 cm3 (22 mm) (main target region (cm3), gap difference between target margin and safety margin (mm)); TR2 = 15.62 cm3 (10 mm); TR3 = 5.62 cm3 (10 mm); and TR4 = 0.9 cm3 (10 mm). For evaluation, the metric success score was used, which represents the percentage of the number of locations with SAR10g,max > 40 W/kg over the total number of locations.
(15) |
2.6. Data Analysis and Statistics
EMF simulation results including the SAR cuboids derived for each TX channel (matrix including averaged SAR10g for each voxel) obtained from CST were imported into Matlab. For post-processing, the first co-simulations were accomplished. By combining results with co-simulation results and obtaining mesh data, B1+ superposition, PTX, and averaged SAR10g were calculated. The calculated averaged SAR of each TX channel was determined using quadratic E-fields, imported into Matlab, and used for MVFS optimization. RF-induced heating metrics for thermal therapy were contoured. For data visualization of the RF heating quality metrics, two groups of radar diagrams involving SAR10g,max and more uniform SAR10g in target and healthy tissues were used. The results obtained from the MTE were translated into heatmaps illustrating five metrics including maximum and mean SAR10g, and TCxx (%). For the heatmaps, each pixel represents the corresponding metric for each TR location center to compare the performance of the RF applicators. Maps including maximum and mean SAR10g were used to examine the performance of the RF applicators to reach a higher temperature. TCxx intensity maps were used to compare the heat uniformity performance of the RF applicators across the brain. Obtaining two sets of intensity maps helps to identify the applicator that best heats different brain regions with higher uniformity or to find a trade-off between these two features. Statistical analysis of the MTE data obtained for all TRs for each RF applicator was performed using a t-test, where p ≤ 0.05 was considered to be statistically significant. To examine the quality of the RF heating, we used TCxx as a uniformity factor, which describes the volume that covers xx% (xx = 25, 50, and 75) of the SAR10g,max inside the TR.
3. Results
3.1. RF Characteristics of the RF Applicators
Both RF applicators were tuned and matched to the resonance frequency of 297.2 MHz (±25 MHz) for the phantom (−45 dB < Sii < −40 dB for the APA and −80 dB < Sii < −70 dB for the HPA, Figure 4a, top row) and for the human head voxel model Duke (−70 dB < Sii < −15 dB for the APA and −70 dB < Sii < −20 dB for the HPA, Figure 4b, top row). For the phantom, a bandwidth (Δf|Sii<−10dB) of ~30 MHz (APA), and ~48 MHz (HPA) was obtained (Figure 4a). For Duke, a bandwidth of ~35 MHz (APA) and ~4.37 MHz (HPA) was found (Figure 4b). For the phantom mutual coupling, the APA was −25 dB < Sij < −15 dB for any neighboring RF building block. The HPA demonstrated a mutual coupling of −80 dB < Sij < −20 dB (Figure 4a, bottom row). For the Duke, the mutual coupling for the APA was −40 dB < Sij < −15 dB for any neighboring RF building block. The HPA demonstrated a mutual coupling of −70 dB< Sij < −10 dB (Figure 4b, bottom row).
3.2. MRI: B1+ Efficiency, B1+ Uniformity and RF Power Deposition
To examine the benefit of the HPA for MRI, superposed B1+,eff [µT/√W] distribution maps were determined for the phantom and for the human voxel model Duke. For the phantom, superposed B1+ efficiency obtained for the HPA in the ROI showed a 67% improvement (IM, mean B1+,eff = 0.96 µT/√W vs. mean B1+,eff = 0.57 µT/√W, Figure 5a,b) and a 10% improvement (RM, mean B1+,eff = 0.94 µT/√W vs. mean B1+,eff = 0.49 µT/√W, Figure 5c,d) of mean B1+ over the APA while the minimum B1+ was similar. For the human head voxel model, B1+ efficiency obtained for the HPA showed a 6% decrease (IM, mean B1+,eff = 0.90 µT/√W vs. mean B1+,eff = 0.96 µT/√W, Figure 5e,f) and 16% decrease (RM, mean B1+,eff = 0.73 µT/√W vs. mean B1+,eff = 0.87 µT/√W, Figure 5g,h) in mean B1+ over the APA. However, the HPA showed a 107% increase (IM, min B1+,eff = 0.31 µT/√W vs. min B1+,eff = 0.15 µT/√W, Figure 5e,f) and 43% increase (RM, min B1+,eff = 0.20 µT/√W vs. min B1+,eff = 0.14 µT/√W, Figure 5g,h) of minimum B1+ over the APA for the brain ROI, which reflects its B1+ efficiency.
Assessment of the B1+ uniformity across the entire phantom demonstrated a 46% reduction (IM, CoV = 0.7 vs. CoV = 1.3, Figure 5a,b) and a 16% increase (RM, CoV = 0.72 vs. CoV 0.62, Figure 5c,d) in the CoV for the HPA versus the APA. Assessment of the B1+ uniformity across the entire human brain voxel model demonstrated a 32% reduction (IM, CoV = 0.3 vs. CoV = 0.5, Figure 5e,f) and 20% reduction (RM, CoV = 0.4 vs. CoV = 0.5, Figure 5g,h) CoV for the HPA versus the APA. These results demonstrate an improved B1+ homogeneity facilitated by the HPA versus the APA.
We examined the MRI metrics derived from PS and APS transmission field shimming of the human head voxel model (Table 2). For the objective of maximizing minimum B1+, the HPA showed a 4% increase (PS, min B1+,eff = 2.12 µT/√W vs. min B1+,eff = 2.04 µT/√W, Table 2) and a 55% increase (APS, min B1+,eff = 2.71 µT/√W vs. min B1+,eff = 1.75 µT/√W, Table 2) versus the APA. Transmission field shimming tailored for CoV minimization resulted in similar (PS, CoV = 0.96, vs. CoV = 0.97, Table 2) and a 42% reduction (APS, CoV = 0.51 vs. CoV = 0.88, Table 2) CoV for the HPA versus the APA. Maximizing mean B1+ revealed a 28% increase (PS, HPA: mean B1+,eff = 10.6 µT/√W, APA: mean B1+,eff = 13.61 µT/√W, Table 2) and a 24% increase (APS, HPA: mean B1+,eff = 11.1 µT/√W, APA: mean B1+,eff = 13.71 µT/√W, Table 2) provided by the APA versus the HPA.
Table 2.
Optimization Goal | pTx Shimming Method | Min B1+ (µT/√kW) | Coefficient of Variation | Mean B1+ (µT/√kW) | |||
---|---|---|---|---|---|---|---|
Helmet Array | Annular Array | Helmet Array | Annular Array | Helmet Array | Annular Array | ||
Max (min B1+) | PS | 2.12 | 2.04 | 0.98 | 1.41 | 8.82 | 9.89 |
APS | 2.71 | 1.75 | 2.87 | 1.62 | 8.78 | 10.81 | |
min (CoV) | PS | 0.06 | 0.48 | 0.96 | 0.97 | 8.10 | 11.01 |
APS | 0.02 | 1.62 | 0.51 | 0.88 | 3.68 | 11.47 | |
Max (Mean B1+) | PS | 0.047 | 0.087 | 0.95 | 1.12 | 10.6 | 13.61 |
APS | 0.34 | 0.01 | 1.33 | 1.99 | 11.1 | 13.71 |
The outcome of the assessment of the RF power deposition is summarized in Table 3. For the phantom, PS pTx using the HPA (SAR10g,WCS = 2.3 W/kg, Table 3) provided a SAR10g,WCS decrement of 4% versus the APA (SAR10g,WCS = 2.4 W/kg, Table 3).
Table 3.
SAR10g,wc (W/kg) | |||
---|---|---|---|
pTx Shimming Method | RF Applicator | Phantom | Human Head Voxel Model |
PS | HPA | 2.3 | 2.3 |
APA | 2.4 | 2.7 | |
APS | HPA | 11.7 | 8.4 |
APA | 14.2 | 9.4 |
For APS pTx, the HPA yielded a SAR10g,WCS decrement of 21% versus the APA (HPA: SAR10g,WCS = 14.2 W/kg, APA: SAR10g,WCS = 11.7 W/kg, Table 3. For the human head voxel model, PS pTX using the HPA (SAR10g,WCS = 2.3 W/kg, Table 3) supported a SAR10g,WCS decrement of 15% over the APA counterpart (SAR10g,WCS = 2.7 W/kg, Table 3). SAR10g,WCS obtained for APS pTX using the HPA (SAR10g,WCS = 8.4 W/kg, Table 3) was 11% lower than for the APA (SAR10g,WCS = 9.4 W/kg, Table 3).
3.3. RF Heating
3.3.1. SAR-Based Indicators in Four Target Locations
Figure 6b shows axial and sagittal SAR10g maps for the four TRs. A quantitative summary of the SAR10g-based indicators of the quality of the RF heating is provided in Table 4.
Table 4.
L1 | L2 | L3 | L4 | |||||
---|---|---|---|---|---|---|---|---|
Locations | Limbic Lobe and Postcentral Gyrus | Thalamus | Corpus Callosum and Limbic Lobe | Parietal Lobe of the Brain | ||||
Metrics | ||||||||
HPA | APA | HPA | APA | HPA | APA | HPA | APA | |
MTS (W/kg) | 49.9 | 38.3 | 59.4 | 50.2 | 50.4 | 37.6 | 53.4 | 40.2 |
Max SAR10g TR (W/kg) | 56.4 | 45.3 | 73.1 | 60.7 | 56.2 | 43.5 | 61.0 | 45.3 |
Max SAR10g HR (W/kg) | 16.5 | 14.1 | 17.7 | 14.6 | 16.6 | 14.4 | 16.7 | 13.9 |
SAF | 3.42 | 3.21 | 4.13 | 4.16 | 3.39 | 3.02 | 3.65 | 3.26 |
Max SAR10g TR/HR (%) | 0.23 | 0.19 | 0.16 | 0.17 | 0.25 | 0.23 | 0.25 | 0.259 |
TC25 (%) | 88.5 | 56.3 | 44.1 | 47.0 | 52.1 | 57.1 | 49.5 | 54.2 |
TC50 (%) | 52.7 | 29.0 | 7.8 | 17.4 | 19.4 | 31.3 | 16.3 | 29.3 |
TC75 (%) | 4.5 | 10.2 | 1.8 | 2.3 | 3.7 | 11.7 | 3.0 | 10.5 |
HC | 0.05 | 0.18 | 0.04 | 0.05 | 0.071 | 0.21 | 0.060 | 0.19 |
Off-TC25 (%) | 73.2 | 58.2 | 82.6 | 56.6 | 73.1 | 58.7 | 72.5 | 56.9 |
Off-TC50 (%) | 34.9 | 34.6 | 38.9 | 36.5 | 35.2 | 35.3 | 35.7 | 33.8 |
Off- TC75 (%) | 16.4 | 15.7 | 14.8 | 17.8 | 16.4 | 15.8 | 16.9 | 16.3 |
Off-HC | 0.22 | 0.27 | 0.18 | 0.31 | 0.22 | 0.27 | 0.233 | 0.29 |
THC | 0.01 | 0.05 | 0.01 | 0.02 | 0.01 | 0.06 | 0.01 | 0.06 |
PI | 149.7 | 68.9 | 106.4 | 97 | 87.9 | 67.1 | 96.6 | 71.2 |
SAR10g,max (TR) is increased by 25% (L1, HPA: SAR10g,max = 56.4 W/kg, APA: SAR10g,max = 45.3 W/kg), 20% (L2, HPA: SAR10g,max = 73.1 W/kg, APA: SAR10g,max = 60.7 W/kg), 29% (L3, HPA: SAR10g,max = 56.2 W/kg, APA: SAR10g,max = 43.5 W/kg), and 35% (L4, HPA: SAR10g,max = 61 W/kg, APA: SAR10g,max = 45.3 W/kg) for the HPA versus the APA. Mean target SAR (MTS) is improved by 30% (L1, HPA: MTS = 50 W/kg, APA: MTS = 38.3 W/kg), 18% (L2, HPA: MTS = 59.4 W/kg, APA: MTS = 50.2 W/kg), 34% (L3, HPA: MTS = 50.4 W/kg, APA: MTS = 37.6 W/kg), and 33% (L4, HPA: MTS = 53.4 W/kg, APA: MTS = 40.2 W/kg) for theHPAcompared to the APA. SAR10g,max < 40 W/kg in healthy tissues was achieved for all four locations for both RF applicators which translates to no hotspots. Instead, off-TCxx and THC show the distribution of SAR10g,max|HR.
For the HPA the SAR10g amplification factor SAF was increased (L1: 7%, HPA: SAF = 3.42, APA: SAF = 3.21; L3: 12%, HPA: SAF = 3.39, APA: SAF = 3.02; L4: 12%, HPA: SAF = 3.65, APA: SAF = 3.26)) for three of the four TR locations while it was similar for L2 (HPA: SAF = 4.13, APA: SAF = 34.16). For enhanced visualization of the RF heating results, Figure 7 illustrates the SAR10g-based metrics in two groups obtained for the target regions L1–L4 and for remote, healthy tissue. The performance indicator PI for the HPA was superior to the APA. Table 4 summarizes the RF heating efficiency and uniformity obtained for the HPA and the APA for L1–L4.
3.3.2. Multi-Target Evaluation
Figure 8 shows the distributions of SAR10g,max, SAR10g,max > 40 W/kg, and MTS, for a central sagittal slice of the brain. The success score (Figure 8c) shows a 25% (HPA: 89%, APA: 71%), 67% (HPA: 75%, APA: 45%), 127% (HPA: 84%, APA: 37%), and 86% (HPA: 65%, APA: 35%) improvement for the HPA versus the APA.
For the large TR1, TCxxs provided by the APA were better than the HPA counterparts for the superior regions of the brain (Figure 9). For the mid and deep inferior regions of the brain, the HPA showed higher TCxxs than the APA (Figure 9). For middle brain regions both RF applicators showed similar uniform SAR10g distribution in the TRs. For the smaller TRs TR2–TR4, TCxxs obtained for the HPA were better than the APA for all brain regions included in MTE (Figure 9).
For a quantitative comparison, Figure 10 shows box plots of the SAR10g,max and MTS for all TRs and locations included in the multi-target evaluation of the HPA and the APA. The highest SAR10g,max (142 W/kg) and MTS (128 W/kg) was achieved by the HPA. Statistical analysis showed that the HPA was superior to the APA for all TRs (p < 0.0001) although the interquartile range is very close (MTS: 11 W/kg (HPA) and 7 W/kg (APA), SAR10g,max: 18 W/kg (HPA), 19 W/Kg (APA)).
3.3.3. Temperature Simulations
SAR10g and temperature distributions obtained for a clinical case of glioblastoma multiforme using Sim4Life “HypT optimizer” are illustrated in Figure 11. The temperature simulations yielded Tmin = 40.2 °C for the HPA and 37.4 °C for the APA inside the TR. For the heating paradigm simulated, a maximum temperature of Tmax = 45.1 °C was found in the TR for the HPA. For the APA Tmax = 45.8 °C was observed in the tumor TR. Figure 12 shows a cumulative plot of the temperature distribution in the tumor TR. The RF heating achieved for the HPA outperformed the APA. The HPA provided T90 = 41.5 °C, T50 = 43.18 °C, and T10 = 44.54 °C while the APA provided T90 = 38.6 °C, T50 = 40.63 °C, and T10 = 43.7 °C.
4. Discussion
This study demonstrates that helmet RF applicators improve the efficacy of ThermalMR by providing enhanced transmission field uniformity for brain MRI, and by enabling enhanced focal point quality for RF-induced heating of brain tumors compared to an annular RF array using the same number of transmit RF elements. The Helmet RF phased array enhances ThermalMR’s RF heating quality and transmission field uniformity across the brain, not by increasing the number of TX channels, but through an optimized rearrangement, as it was shown that 16 elements can outperform 32 elements [10]. Given the limited surface area of the head and spatial constraints, the HPA strategically places two SGBT elements on top of the head. This innovative configuration overcomes spatial limitations and improves the performance of the RF array by ensuring a more effective and uniform distribution of RF energy, demonstrating a significant advancement in hyperthermia therapy and ThermalMR technologies without the need for increasing element density. Our EMF and temperature simulations confirm the hypothesis that these transmission elements placed on top of the head improve performance criteria critical to MRI and enhance the temperature focusing of conventional annular array RF applicators, especially in the superior regions of the brain.
Published reports on dome-shaped RF applicators customized for targeting brain regions have shown that these transmitter array configurations have value for UHF-MR. However, none of these published RF arrays used transmission elements placed perpendicular to the cranial–caudal axis of the body or to the main magnetic field of an MR scanner [21,31,36,37]. The current study is the first report demonstrating the performance improvement of a helmet RF applicator for ThermalMR over an APA using the same number of transmission elements. This improvement facilitates the integration of diagnostic imaging guidance, thermal treatment, and MR temperature cartography-based monitoring of RF heating in a single, multi-purpose RF applicator to enhance thermal theranostics, and to better describe the role of temperature in biological systems and disease. In [10,21], different types of APAs were compared to find the most advanced solution for APAs. This work builds upon an APA configuration, enhancing it with the HPA by adding two additional elements to an 8-channel APA, thus broadening brain coverage. This improvement recognizes that brain tumors and target areas have varied shapes and sizes, often extending beyond the APA’s typical coverage. Moreover, the RF applicator setup should be centered over the brain to maintain accuracy to support MR imaging and thermometry during treatment. The adaptability of the RF applicator, crucial for effective therapy, is retained in the HPA configuration. It allows for the adjustment of RF elements along the head for optimal positioning relative to the tumor location, provided that B1+ homogeneity remains acceptable in the Region of Interest (ROI). This highlights the significance of a flexible and movable RF applicator system like the HPA, which not only enhances the traditional APA setup but also ensures optimized treatment and imaging efficiency, regardless of the tumor’s size, shape, or location within the brain. A limitation of our study is the limited number of transmission elements used. The restriction to using only ten SGBT elements for the annular array reference is a result of the minimum inter-element distance and inter-element coupling constraints. The HPA demonstrated an improved mutual decoupling of ~10%. Adding an extra ring of TX elements along the cranial–caudal axis [10] would enhance anatomical coverage in the superior–inferior direction and provide extra degrees of freedom for optimizing excitation vectors tailored for MRI and RF heating. This benefit could be exploited for further SAR10g reduction and B1+ uniformity improvements for MRI and enhanced targeted RF power deposition in deep-seated brain tumors using annular array configurations. However, adding a second ring to the annular array would double the number of TX channels. This would present a cost constraint, driven primarily by the costs of the RF power amplifiers. This would also pose a practical obstacle since current pTX systems of MRI scanners are limited to 8–16 independent transmission channels. In previous approaches to ThermalMR RF applicator design, increasing the number of elements from 8 to 32 in different numbers of rows was studied [10,21]. In this simulation study, 10-SGBT was the maximum number of TX elements that can fit in one APA to compare its full potential with an APA. Therefore, the HPA approach is more cost-effective than multiple rings of TX elements used in an annular array. Beyond the helmet RF applicator with ten TX elements examined in this proof-of-principle study, the range of possible alternative helmet RF applicator configurations is even larger. Our study demonstrates for the first time that the helmet design approach is promising for MRI and HT, and further explorations of alternative helmet-based applicator configurations are likely to prove fruitful.
The HPA configuration examined in this work takes the elliptical shape of the human head into account and aligns the long axis of the SGBT building blocks placed on top of the head with the longest (superior-inferior) axis of the head for the benefit of better head and brain coverage. Aligning the long axis of the SGBT building blocks placed on top of the head with the left–right axis of the head would also be a viable alternative arrangement. Our simulations used the same distance from the center of the left–right direction of the brain for each SGBT building block placed on top of the head. Asymmetric positioning of the SGBT buildings placed on top of the head around the center of the left-right direction of the brain is an alternative approach. The center point of the SGBT building blocks placed on top of the head was aligned with the center of the anterior-posterior direction of the brain. However, off-center positioning of the SGBT buildings placed on top of the head is also feasible.
The reproducibility of EMF simulations is an ongoing discussion. This is not only due to insufficient disclosure and description of the physical setups. Additionally, there are typically too many parameters to be specified in the simulation process, and it is hardly feasible to repeat or reproduce the entire set of parameters in a study. Finally, these parameters may change with every simulation tool and algorithm, with even every simulation software version and human voxel model. Fortunately, these constraints typically do not compromise the main results of an EMF simulation, but—in a strict sense—can be critical for the important principle of reproducibility. Therefore, in this work, phantom results served as a form of ground truth to be easier reproduced although our main results are obtained using the Duke human head voxel models. Analyzing results with the MTE approach, Figure 8 and Figure 9 reveal extensive details on RF applicator performance. To mimic a realistic clinical scenario, our simulations include patient-specific model extraction (n = 1) obtained from CT images. For clinical application details about the type of tumor tissue (extremely dense, heterogeneously dense, scattered fibroglandular and predominantly fatty, non-uniform perfusion) need to be included in the hyperthermia treatment planning [74].
Figure 8 shows APA’s inconsistent performance versus HPA in superior regions for TR1, with a decline to zero in TR2 and TR3, highlighting the top antennas’ importance. The reason behind the superior performance of the HPA over the APA in the lower brain/spinal cord area in Figure 8 for TR1 might be because of EM wave interference of top antennas inside the MR waveguide [75].
Figure 9 introduces TCxx, differing from maximum or mean SAR, as a homogeneity measure of SAR distribution within TRs, affected by SAR range. The MTE approach illustrates a reduction in TCxx, influenced by TR dimensions and the diverse sizes and thermal properties of brain tissues, complicating TCxx predictions. The Supplementary Videos S1–S9 illustrate SAR distribution variances across TRs and locations. This complexity emphasizes the MTE’s role in dissecting these relationships. Figure 9 shows TCxx values decreasing from TC25 to TC75 across TRs, with TC75 nearing zero for all, indicating minimal variance. Our MTE approach provides a technical foundation for a more objective RF applicator evaluation using whole-brain accessibility instead of a limited set of specific but arbitrary target locations, which may not represent the whole clinically relevant picture. This achievement presents a foundation for further RF applicator design tailored for ThermalMR-based therapy of brain tumors. The MTE approach has the potential to become a standard for benchmarking RF-applicator designs for a broad range of applications, not only limited to the brain but also for HT in other anatomical targets including extremities and abdomen. Timely computation and optimization of the excitation vectors targeting the high number of TR locations used for MTE is facilitated by the time multiplexing vector field shaping approach. The MVFS approach efficiently handles extensive sets of optimization constraints and provides an optimal solution through a minimal number of rapid iterative computations. The runtime is only minimally influenced by the total quantity of SAR matrices within the model. A computation time for each time-interleaved solution <1 s was used for an individual target using a mid-tier consumer PC. Considering 2–3 time intervals for each TR, whole brain slice coverage required a computation time of ~14 h. These computation times can be reduced using parallel computing. Further acceleration can be achieved by spatial undersampling to reduce the number of target points with respect to the TR size. With the MVFS, excitation vectors can be customized to match the size and arbitrary geometry of individual tumor volumes to meet the HT planning requirements of individual patients and targets. In this work, we used cuboidal target regions rather than cylindrical or spherical TRs to make the TR more unpredictable, and less symmetrical, than the symmetrical applicator arrangement of the annular array. This cuboidal target poses greater challenges for RF targeting compared to spherical TRs, primarily due to the typical development of beamforming techniques focused on the center of the target region. MVFS-based excitation vector optimization is not limited to a single CTV or GTV but also supports simultaneous targeting of multiple CTVs or GTVs [44]. This is consistent with the needs of personalized medicine and can be achieved without necessitating patient-specific RF applicator hardware. The performance improvement using HPA is not dependent on the focusing algorithm but it is related to the antenna arrangement. The HperT optimizer tool in Sim4life was utilized for this purpose.
It is a recognized limitation of our proof-of-principle study that the traditional Pennes Bioheat equation has been used for temperature simulations. This approach uses an approximation of uniform or isotropic blood perfusion. Based on the ESHO benchmarks for computational modeling and optimization in hyperthermia therapy [54], our work used blood perfusion rates (kg/s/m3) for muscle, fat, and tumor to approximate heterogeneities in the blood perfusion under baseline and under thermal stress. Very recently, an advanced version of the Pennes bioheat equation was proposed to take into account heterogeneous or anisotropic blood perfusion [76].
Replacing the water bolus filled with deionized water placed between the RF building blocks and the head with high dielectric materials offers another research direction to further improve the MRI performance and heating efficacy. The use of high permittivity materials would enhance wavelength shortening and would facilitate size reduction of the SGBT building blocks [77]. The preference would be high permittivity slurries over ceramics to maintain some of the cooling effects of the water bolus. The use of metamaterial surfaces is also conceptually appealing for pursuing the development of ThermalMR applicators due to the extra degrees of freedom for shaping electromagnetic wave propagation and constructive interference in the target region [77,78,79]. This benefit could facilitate SAR10g reduction and B1+ uniformity improvements for MRI and enhance targeted RF power deposition in deep-seated brain tumors.
5. Conclusions
This work demonstrates the enhanced performance of the helmet RF applicator compared to an annular array in terms of transmission field coverage and uniformity across the brain, which is essential for MRI diagnostics of cancer. Our findings document that the HPA facilitates a ~10% improvement of SAR10g,max in the target region versus the annular array, which augments hyperthermia treatment as an adjunct to chemo- and radiotherapy of brain tumors. To conclude, our results provide a technical foundation for objective RF applicator evaluation using whole brain slice coverage instead of a few specific but arbitrary target locations using the MTE approach. Our findings constitute a foundation for the experimental implementation and application of a helmet array driven by broadband self-grounded bow tie antenna building blocks en route to ThermalMR theranostics of brain tumors.
Acknowledgments
The authors wish to thank Alexander Raaijmakers, (University of Eindhoven, Eindhoven, The Netherlands) for the fruitful discussion and Maria del Mar Miñana Maiques, ZMT (Member of Zurich43, Zurich, Switzerland) for her support.
Supplementary Materials
The following supporting information can be downloaded at https://www.mdpi.com/article/10.3390/bioengineering11070733/s1. Video S1: MTE. The basic scheme of the multi-target evaluation (MTE) framework is shown in this video for a specific TR3 size, using the HPA for mapping SAR10g,max. For MTE, hypothetical TRs (borderlines marked in black and green) are moved across the entire brain slice for the evaluation of the quality of targeted RF heating instead of using the conventional approach of defining a limited number of specific but arbitrary TRs. EMF simulations were performed for each TR position across a 26 × 27 rectangular grid with 702 points (step size = 7 mm). For evaluation, the metric success score was used, which represents the percentage of the number of locations with SAR10g,max > 40 W/kg over the total number of locations. Videos S2–S9: APA/HPA_TR1-TR4_MTE.
Author Contributions
Conceptualization, F.R. and T.N.; EMF simulations, F.R.; data analysis, F.R., B.N., J.M.M. and T.W.E.; optimization algorithm programming, A.K., F.R. and M.B.; patient model generation, E.O. and P.G., writing—original draft preparation, F.R., T.N. and J.M.M.; writing—review and editing, T.N., F.R., T.W.E., B.N., E.O., J.M.M. and R.S.; visualization, F.R. and T.N.; funding acquisition, T.N. All authors have read and agreed to the published version of the manuscript.
Institutional Review Board Statement
The local ethics board approved this study (EA 2/236/19).
Informed Consent Statement
Written informed consent was acquired from the patient with respect to RT treatment and clinical data management for research purposes.
Data Availability Statement
The data presented in this study are available on request from the corresponding author due to privacy reasons.
Conflicts of Interest
Thoralf Niendorf is the founder and CEO of MRI.TOOLS GmbH, Berlin, Germany. The authors declare no conflicts of interest.
Funding Statement
This project has received funding from the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation program under grant agreement No. 743077 (Thermal MR) and from the Innovative Training Network (ITN) H2020-MSCA-ITN-2020-955625 (HYPERBOOST) of the Marie Skłodowska-Curie Actions of the European Union.
Footnotes
Disclaimer/Publisher’s Note: The statements, opinions and data contained in all publications are solely those of the individual author(s) and contributor(s) and not of MDPI and/or the editor(s). MDPI and/or the editor(s) disclaim responsibility for any injury to people or property resulting from any ideas, methods, instructions or products referred to in the content.
References
- 1.Lee Titsworth W., Murad G.J., Hoh B.L., Rahman M. Fighting fire with fire: The revival of thermotherapy for gliomas. Anticancer Res. 2014;34:565–574. [PubMed] [Google Scholar]
- 2.Wust P., Hildebrandt B., Sreenivasa G., Rau B., Gellermann J., Riess H., Felix R., Schlag P.M. Hyperthermia in combined treatment of cancer. Lancet Oncol. 2002;3:487–497. doi: 10.1016/S1470-2045(02)00818-5. [DOI] [PubMed] [Google Scholar]
- 3.Rock K., McArdle O., Forde P., Dunne M., Fitzpatrick D., O’Neill B., Faul C. A clinical review of treatment outcomes in glioblastoma multiforme--the validation in a non-trial population of the results of a randomised Phase III clinical trial: Has a more radical approach improved survival? Br. J. Radiol. 2012;85:e729–e733. doi: 10.1259/bjr/83796755. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 4.Hanif F., Muzaffar K., Perveen K., Malhi S.M., Simjee Sh U. Glioblastoma Multiforme: A Review of its Epidemiology and Pathogenesis through Clinical Presentation and Treatment. Asian Pac. J. Cancer Prev. 2017;18:3–9. doi: 10.22034/apjcp.2017.18.1.3. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 5.Dai Q., Cao B., Zhao S., Zhang A. Synergetic Thermal Therapy for Cancer: State-of-the-Art and the Future. Bioengineering. 2022;9:474. doi: 10.3390/bioengineering9090474. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 6.Kok H.P., Cressman E.N.K., Ceelen W., Brace C.L., Ivkov R., Grull H., Ter Haar G., Wust P., Crezee J. Heating technology for malignant tumors: A review. Int. J. Hyperth. 2020;37:711–741. doi: 10.1080/02656736.2020.1779357. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 7.Seebass M., Beck R., Gellermann J., Nadobny J., Wust P. Electromagnetic phased arrays for regional hyperthermia: Optimal frequency and antenna arrangement. Int. J. Hyperth. Off. J. Eur. Soc. Hyperthermic Oncol. N. Am. Hyperth. Group. 2001;17:321–336. doi: 10.1080/02656730110049529. [DOI] [PubMed] [Google Scholar]
- 8.Wust P., Veltsista P.D., Oberacker E., Yavvari P., Walther W., Bengtsson O., Sterner-Kock A., Weinhart M., Heyd F., Grabowski P., et al. Radiofrequency Electromagnetic Fields Cause Non-Temperature-Induced Physical and Biological Effects in Cancer Cells. Cancers. 2022;14:5349. doi: 10.3390/cancers14215349. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 9.Han H., Eigentler T.W., Wang S., Kretov E., Winter L., Hoffmann W., Grass E., Niendorf T. Design, Implementation, Evaluation and Application of a 32-Channel Radio Frequency Signal Generator for Thermal Magnetic Resonance Based Anti-Cancer Treatment. Cancers. 2020;12:1720. doi: 10.3390/cancers12071720. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 10.Oberacker E., Kuehne A., Oezerdem C., Nadobny J., Weihrauch M., Beck M., Zschaeck S., Diesch C., Eigentler T.W., Waiczies H., et al. Radiofrequency applicator concepts for thermal magnetic resonance of brain tumors at 297 MHz (7.0 Tesla) Int. J. Hyperth. 2020;37:549–563. doi: 10.1080/02656736.2020.1761462. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 11.Paulides M.M., Curto S., Wu M., Winter L., Rhoon G.C.v., Yeo D.T.B. Advances in magnetic resonance guided radiofrequency hyperthermia; Proceedings of the 2017 11th European Conference on Antennas and Propagation (EUCAP); Paris, France. 19–24 March 2017; pp. 3692–3696. [Google Scholar]
- 12.Ji Y., Winter L., Navarro L., Ku M.C., Periquito J.S., Pham M., Hoffmann W., Theune L.E., Calderon M., Niendorf T. Controlled Release of Therapeutics from Thermoresponsive Nanogels: A Thermal Magnetic Resonance Feasibility Study. Cancers. 2020;12:1380. doi: 10.3390/cancers12061380. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 13.Feddersen T.V., Hernandez-Tamames J.A., Franckena M., van Rhoon G.C., Paulides M.M. Clinical Performance and Future Potential of Magnetic Resonance Thermometry in Hyperthermia. Cancers. 2021;13:31. doi: 10.3390/cancers13010031. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 14.Curto S., Seabra C.C., Sumser K., Paulides M.M., Rhoon G.C.v. MR thermometry in hyperthermia: Imaging for precise therapy monitoring with the novel Universal Arch applicator; Proceedings of the 2022 International Workshop on Antenna Technology (iWAT); Dublin, Ireland. 16–18 May 2022; pp. 210–212. [Google Scholar]
- 15.Paulides M.M., Bakker J.F., Neufeld E., van der Zee J., Jansen P.P., Levendag P.C., van Rhoon G.C. Winner of the “New Investigator Award” at the European Society of Hyperthermia Oncology Meeting 2007. The HYPERcollar: A novel applicator for hyperthermia in the head and neck. Int. J. Hyperth. 2007;23:567–576. doi: 10.1080/02656730701670478. [DOI] [PubMed] [Google Scholar]
- 16.Togni P., Rijnen Z., Numan W.C., Verhaart R.F., Bakker J.F., van Rhoon G.C., Paulides M.M. Electromagnetic redesign of the HYPERcollar applicator: Toward improved deep local head-and-neck hyperthermia. Phys. Med. Biol. 2013;58:5997–6009. doi: 10.1088/0031-9155/58/17/5997. [DOI] [PubMed] [Google Scholar]
- 17.Winter L., Ozerdem C., Hoffmann W., Santoro D., Muller A., Waiczies H., Seemann R., Graessl A., Wust P., Niendorf T. Design and evaluation of a hybrid radiofrequency applicator for magnetic resonance imaging and RF induced hyperthermia: Electromagnetic field simulations up to 14.0 Tesla and proof-of-concept at 7.0 Tesla. PLoS ONE. 2013;8:e61661. doi: 10.1371/journal.pone.0061661. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 18.Curry T.S., Dowdey J.E., Murry R.C. Christensen’s Physics of Diagnostic Radiology. Lippincott Williams & Wilkins; Philadelphia, PA, USA: 1990. [Google Scholar]
- 19.Guerin B., Villena J.F., Polimeridis A.G., Adalsteinsson E., Daniel L., White J.K., Rosen B.R., Wald L.L. Computation of ultimate SAR amplification factors for radiofrequency hyperthermia in non-uniform body models: Impact of frequency and tumour location. Int. J. Hyperth. 2018;34:87–100. doi: 10.1080/02656736.2017.1319077. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 20.Winter L., Oezerdem C., Hoffmann W., van de Lindt T., Periquito J., Ji Y., Ghadjar P., Budach V., Wust P., Niendorf T. Thermal magnetic resonance: Physics considerations and electromagnetic field simulations up to 23.5 Tesla (1GHz) Radiat. Oncol. 2015;10:201. doi: 10.1186/s13014-015-0510-9. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 21.Oberacker E., Kuehne A., Nadobny J., Zschaeck S., Weihrauch M., Waiczies H., Ghadjar P., Wust P., Niendorf T., Winter L. Radiofrequency applicator concepts for simultaneous MR imaging and hyperthermia treatment of glioblastoma multiforme. Curr. Dir. Biomed. Eng. 2017;3:473–477. doi: 10.1515/cdbme-2017-0100. [DOI] [Google Scholar]
- 22.Lattanzi R., Wiggins G.C., Zhang B., Duan Q., Brown R., Sodickson D.K. Approaching ultimate intrinsic signal-to-noise ratio with loop and dipole antennas. Magn. Reson. Med. 2018;79:1789–1803. doi: 10.1002/mrm.26803. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 23.Raaijmakers E.A.L., Mestrom R.M.C., Sumser K., Salim G., van Rhoon G.C., Essers J., Paulides M.M. An MR-compatible antenna and application in a murine superficial hyperthermia applicator. Int. J. Hyperth. 2018;34:697–703. doi: 10.1080/02656736.2017.1369172. [DOI] [PubMed] [Google Scholar]
- 24.Eigentler T.W., Winter L., Han H., Oberacker E., Kuehne A., Waiczies H., Schmitter S., Boehmert L., Prinz C., Trefna H.D., et al. Wideband Self-Grounded Bow-Tie Antenna for Thermal MR. NMR Biomed. 2020;33:e4274. doi: 10.1002/nbm.4274. [DOI] [PubMed] [Google Scholar]
- 25.Zanoli M., Ek E., Dobsicek Trefna H. Antenna Arrangement in UWB Helmet Brain Applicators for Deep Microwave Hyperthermia. Cancers. 2023;15:1447. doi: 10.3390/cancers15051447. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 26.Aram M.G., Aliakbarian H., Trefná H.D. A phased array applicator based on open ridged-waveguide antenna for microwave hyperthermia. Microw. Opt. Technol. Lett. 2021;63:3086–3091. doi: 10.1002/mop.33039. [DOI] [Google Scholar]
- 27.Guerin B., Villena J.F., Polimeridis A.G., Adalsteinsson A., Daniel L., White J.K., Rosen B.R., Wald L.L. Ultimate hyperthermia: Computation of the best achievable radio-frequency hyperthermia treatments in non-uniform body models; Proceedings of the 24th Annual Meeting of the ISMRM; Singapore. 7–13 May 2016. [Google Scholar]
- 28.Oberacker E., Diesch C., Nadobny J., Kuehne A., Wust P., Ghadjar P., Niendorf T. Patient-Specific Planning for Thermal Magnetic Resonance of Glioblastoma Multiforme. Cancers. 2021;13:1867. doi: 10.3390/cancers13081867. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 29.Lakshmanan K., Cloos M., Brown R., Lattanzi R., Sodickson D.K., Wiggins G.C. The “Loopole” Antenna: A Hybrid Coil Combining Loop and Electric Dipole Properties for Ultra-High-Field MRI. Concepts Magn. Reson. Part. B Magn. Reson. Eng. 2020;2020:8886543. doi: 10.1155/2020/8886543. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 30.Guerin B., Angelone L.M., Dougherty D., Wald L.L. Parallel transmission to reduce absorbed power around deep brain stimulation devices in MRI: Impact of number and arrangement of transmit channels. Magn. Reson. Med. 2020;83:299–311. doi: 10.1002/mrm.27905. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 31.Avdievich N.I., Nikulin A.V., Ruhm L., Magill A.W., Glang F., Henning A., Scheffler K. A 32-element loop/dipole hybrid array for human head imaging at 7 T. Magn. Reson. Med. 2022;88:1912–1926. doi: 10.1002/mrm.29347. [DOI] [PubMed] [Google Scholar]
- 32.Erturk M.A., Raaijmakers A.J., Adriany G., Ugurbil K., Metzger G.J. A 16-channel combined loop-dipole transceiver array for 7 Tesla body MRI. Magn. Reson. Med. 2017;77:884–894. doi: 10.1002/mrm.26153. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 33.Woo M.K., DelaBarre L., Lee B.Y., Waks M., Lagore R.L., Radder J., Eryaman Y., Ugurbil K., Adriany G. Evaluation of a 16-channel transceiver loop + dipole antenna array for human head imaging at 10.5 tesla. IEEE Access. 2020;8:203555–203563. doi: 10.1109/ACCESS.2020.3036598. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 34.Pfrommer A., Henning A. The ultimate intrinsic signal-to-noise ratio of loop- and dipole-like current patterns in a realistic human head model. Magn. Reson. Med. 2018;80:2122–2138. doi: 10.1002/mrm.27169. [DOI] [PubMed] [Google Scholar]
- 35.Dobsicek Trefna H. EP-1271: Development of focused microwave hyperthermia of pediatric brain cance. Radiother. Oncol. 2015;115:S685–S686. doi: 10.1016/S0167-8140(15)41263-0. [DOI] [Google Scholar]
- 36.Lou F., Tang X., Quan Z., Qian M., Wang J., Qu S., Gao Y., Wang Y., Pan G., Lai H.Y., et al. A 16-channel loop array for in vivo macaque whole-brain imaging at 7 T. Magn. Reson. Imaging. 2023;102:179–183. doi: 10.1016/j.mri.2023.06.014. [DOI] [PubMed] [Google Scholar]
- 37.Shajan G., Kozlov M., Hoffmann J., Turner R., Scheffler K., Pohmann R. A 16-channel dual-row transmit array in combination with a 31-element receive array for human brain imaging at 9.4 T. Magn. Reson. Med. 2014;71:870–879. doi: 10.1002/mrm.24726. [DOI] [PubMed] [Google Scholar]
- 38.Eigentler T.W., Kuehne A., Boehmert L., Dietrich S., Els A., Waiczies H., Niendorf T. 32-Channel self-grounded bow-tie transceiver array for cardiac MR at 7.0T. Magn. Reson. Med. Off. J. Soc. Magn. Reson. Med./Soc. Magn. Reson. Med. 2021;86:2862–2879. doi: 10.1002/mrm.28885. [DOI] [PubMed] [Google Scholar]
- 39.Nurzed B., Kuehne A., Aigner C.S., Schmitter S., Niendorf T., Eigentler T.W. Radiofrequency Antenna Concepts for Human Cardiac MR at 14.0 T. MAGMA. 2023;36:257–277. doi: 10.1007/s10334-023-01075-1. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 40.Vaidya M.V., Collins C.M., Sodickson D.K., Brown R., Wiggins G.C., Lattanzi R. Dependence of B1+ and B1- Field Patterns of Surface Coils on the Electrical Properties of the Sample and the MR Operating Frequency. Concepts Magn. Reson. Part B Magn. Reson. Eng. 2016;46:25–40. doi: 10.1002/cmr.b.21319. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 41.Abragam A. Principles of Nuclear Magnetism (International Series of Monographs on Physics) Oxford University Press; Oxford, UK: 1983. [Google Scholar]
- 42.Lattanzi R., Sodickson D.K., Grant A.K., Zhu Y. Electrodynamic constraints on homogeneity and radiofrequency power deposition in multiple coil excitations. Magn. Reson. Med. 2009;61:315–334. doi: 10.1002/mrm.21782. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 43.Schooneveldt G., Bakker A., Balidemaj E., Chopra R., Crezee J., Geijsen E.D., Hartmann J., Hulshof M.C., Kok H.P., Paulides M.M., et al. Thermal dosimetry for bladder hyperthermia treatment. An overview. Int. J. Hyperth. 2016;32:417–433. doi: 10.3109/02656736.2016.1156170. [DOI] [PubMed] [Google Scholar]
- 44.Kuehne A., Oberacker E., Waiczies H., Niendorf T. Solving the time-and frequency-multiplexed problem of constrained radiofrequency induced hyperthermia. Cancers. 2020;12:1072. doi: 10.3390/cancers12051072. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 45.Takook P., Persson M., Gellermann J., Trefna H.D. Compact self-grounded Bow-Tie antenna design for an UWB phased-array hyperthermia applicator. Int. J. Hyperth. 2017;33:387–400. doi: 10.1080/02656736.2016.1271911. [DOI] [PubMed] [Google Scholar]
- 46.Griffiths D.J. Introduction to Electrodynamics. Cambridge University Press; Cambridge, UK: 2023. [Google Scholar]
- 47.Pozar D.M. Microwave Engineering. John Wiley & Sons; Hoboken, NJ, USA: 2011. [Google Scholar]
- 48.Kok H.P., Ciampa S., de Kroon-Oldenhof R., Steggerda-Carvalho E.J., van Stam G., Vörding P.J.Z.V.S., Stalpers L.J., Geijsen E.D., Bardati F., Bel A. Toward online adaptive hyperthermia treatment planning: Correlation between measured and simulated specific absorption rate changes caused by phase steering in patients. Int. J. Radiat. Oncol. Biol. Phys. 2014;90:438–445. doi: 10.1016/j.ijrobp.2014.05.1307. [DOI] [PubMed] [Google Scholar]
- 49.Eryaman Y., Guerin B., Keil B., Mareyam A., Herraiz J.L., Kosior R.K., Martin A., Torrado-Carvajal A., Malpica N., Hernandez-Tamames J.A., et al. SAR reduction in 7T C-spine imaging using a “dark modes” transmit array strategy. Magn. Reson. Med. 2015;73:1533–1539. doi: 10.1002/mrm.25246. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 50.Balanis C. Antenna Theory: Analysis and Design. Wiley-Interscience; New York, NY, USA: 2005. [Google Scholar]
- 51.Dorsey W., Stumme A., Coleman J. Naval Research Lab. Tutorial: Applying Phase-Mode Theory to the Design of Cylindrical Arrays. Naval Research Laboratory; Washington, DC, USA: 2019. p. 12. Tech. Rep. NRL/MR/5310–19-9915. [Google Scholar]
- 52.Winter L., Oberacker E., Paul K., Ji Y., Oezerdem C., Ghadjar P., Thieme A., Budach V., Wust P., Niendorf T. Magnetic resonance thermometry: Methodology, pitfalls and practical solutions. Int. J. Hyperth. 2016;32:63–75. doi: 10.3109/02656736.2015.1108462. [DOI] [PubMed] [Google Scholar]
- 53.Restivo M.C., van den Berg C.A., van Lier A.L., Polders D.L., Raaijmakers A.J., Luijten P.R., Hoogduin H. Local specific absorption rate in brain tumors at 7 tesla. Magn. Reson. Med. 2016;75:381–389. doi: 10.1002/mrm.25653. [DOI] [PubMed] [Google Scholar]
- 54.Paulides M.M., Rodrigues D.B., Bellizzi G.G., Sumser K., Curto S., Neufeld E., Montanaro H., Kok H.P., Dobsicek Trefna H. ESHO benchmarks for computational modeling and optimization in hyperthermia therapy. Int. J. Hyperth. 2021;38:1425–1442. doi: 10.1080/02656736.2021.1979254. [DOI] [PubMed] [Google Scholar]
- 55.Wust P., Stahl H., Loffel J., Seebass M., Riess H., Felix R. Clinical, physiological and anatomical determinants for radiofrequency hyperthermia. Int. J. Hyperth. 1995;11:151–167. doi: 10.3109/02656739509022453. [DOI] [PubMed] [Google Scholar]
- 56.Pennes H.H. Analysis of tissue and arterial blood temperatures in the resting human forearm. J. Appl. Physiol. 1948;1:93–122. doi: 10.1152/jappl.1948.1.2.93. [DOI] [PubMed] [Google Scholar]
- 57.Shih T.C., Yuan P., Lin W.L., Kou H.S. Analytical analysis of the Pennes bioheat transfer equation with sinusoidal heat flux condition on skin surface. Med. Eng. Phys. 2007;29:946–953. doi: 10.1016/j.medengphy.2006.10.008. [DOI] [PubMed] [Google Scholar]
- 58.Tilly W., Wust P., Rau B., Harder C., Gellermann J., Schlag P., Budach V., Felix R. Temperature data and specific absorption rates in pelvic tumours: Predictive factors and correlations. Int. J. Hyperth. 2001;17:172–188. doi: 10.1080/02656730150502323. [DOI] [PubMed] [Google Scholar]
- 59.Neufeld E., Paulides M.M., van Rhoon G.C., Kuster N. Numerical modeling for simulation and treatment planning of thermal therapy. Phys. Therm. Ther. Fundam. Clin. Appl. 2013;8:119–136. [Google Scholar]
- 60.Chipperfield A., Fleming P., Fonseca C. Adaptive Computing in Engineering Design and Control. Springer; Berlin/Heidelberg, Germany: 1994. Genetic algorithm tools for control systems engineering; p. 133. [Google Scholar]
- 61.Coleman T., Branch M.A., Grace A. Optimization Toolbox. For Use with MATLAB. User’s Guide for MATLAB 5. The “MathWorks” Inc.; Natick, MA, USA: 1995. Version 2, Relaese II 1999. [Google Scholar]
- 62.Mao W., Smith M.B., Collins C.M. Exploring the limits of RF shimming for high-field MRI of the human head. Magn. Reson. Med. 2006;56:918–922. doi: 10.1002/mrm.21013. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 63.Rahimi F., Chamaani S. Applying a repetitive time-reversal method to reduce input power of a wearable hyperthermia applicator for breast cancer treatment. Microw. Opt. Technol. Lett. 2020;62:3754–3766. doi: 10.1002/mop.32518. [DOI] [Google Scholar]
- 64.Zastrow E., Hagness S.C., Van Veen B.D., Medow J.E. Time-multiplexed beamforming for noninvasive microwave hyperthermia treatment. IEEE Trans. Biomed. Eng. 2011;58:1574–1584. doi: 10.1109/TBME.2010.2103943. [DOI] [PubMed] [Google Scholar]
- 65.Georgakis I.P., Polimeridis A.G., Lattanzi R. A formalism to investigate the optimal transmit efficiency in radiofrequency shimming. NMR Biomed. 2020;33:e4383. doi: 10.1002/nbm.4383. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 66.Lattanzi R., Grant A.K., Polimeni J.R., Ohliger M.A., Wiggins G.C., Wald L.L., Sodickson D.K. Performance evaluation of a 32-element head array with respect to the ultimate intrinsic SNR. NMR Biomed. 2010;23:142–151. doi: 10.1002/nbm.1435. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 67.Padormo F., Beqiri A., Hajnal J.V., Malik S.J. Parallel transmission for ultrahigh-field imaging. NMR Biomed. 2016;29:1145–1161. doi: 10.1002/nbm.3313. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 68.What’s new in MR safety: The latest on the safe use of equipment in the magnetic resonance environment. Health Devices. 2005;34:333–349. [PubMed] [Google Scholar]
- 69.Wu X., Chang T.-H., Luo Z.-Q., Akgun C.E., Vaughan J.T., Uğurbil K., Moortele P.-F.v.d. Worst case SAR scenario as a new metric for SAR analysis in B 1 phase; Proceedings of the Proceedings 16th Scientific Meeting, International Society for Magnetic Resonance in Medicine; Toronto, ON, Canada. 3–9 May 2008. [Google Scholar]
- 70.Canters R.A., Wust P., Bakker J.F., Van Rhoon G.C. A literature survey on indicators for characterisation and optimisation of SAR distributions in deep hyperthermia, a plea for standardisation. Int. J. Hyperth. 2009;25:593–608. doi: 10.3109/02656730903110539. [DOI] [PubMed] [Google Scholar]
- 71.Bellizzi G.G., Drizdal T., van Rhoon G.C., Crocco L., Isernia T., Paulides M.M. The potential of constrained SAR focusing for hyperthermia treatment planning: Analysis for the head & neck region. Phys. Med. Biol. 2018;64:015013. doi: 10.1088/1361-6560/aaf0c4. [DOI] [PubMed] [Google Scholar]
- 72.Lee H.K., Antell A.G., Perez C.A., Straube W.L., Ramachandran G., Myerson R.J., Emami B., Molmenti E.P., Buckner A., Lockett M.A. Superficial hyperthermia and irradiation for recurrent breast carcinoma of the chest wall: Prognostic factors in 196 tumors. Int. J. Radiat. Oncol. Biol. Phys. 1998;40:365–375. doi: 10.1016/S0360-3016(97)00740-2. [DOI] [PubMed] [Google Scholar]
- 73.Bellizzi G.G., Drizdal T., van Rhoon G.C., Crocco L., Isernia T., Paulides M.M. Predictive value of SAR based quality indicators for head and neck hyperthermia treatment quality. Int. J. Hyperth. 2019;36:456–465. doi: 10.1080/02656736.2019.1590652. [DOI] [PubMed] [Google Scholar]
- 74.Singh M., Singh T., Soni S. Pre-operative Assessment of Ablation Margins for Variable Blood Perfusion Metrics in a Magnetic Resonance Imaging Based Complex Breast Tumour Anatomy: Simulation Paradigms in Thermal Therapies. Comput. Methods Programs Biomed. 2021;198:105781. doi: 10.1016/j.cmpb.2020.105781. [DOI] [PubMed] [Google Scholar]
- 75.Brunner D.O., Paska J., Froehlich J., Pruessmann K.P. Traveling-wave RF shimming and parallel MRI. Magn. Reson. Med. 2011;66:290–300. doi: 10.1002/mrm.22817. [DOI] [PubMed] [Google Scholar]
- 76.Manpreet S. Modified Pennes bioheat equation with heterogeneous blood perfusion: A newer perspective. Int. J. Heat. Mass. Transf. 2024;218:124698. doi: 10.1016/j.ijheatmasstransfer.2023.124698. [DOI] [Google Scholar]
- 77.Webb A., Shchelokova A., Slobozhanyuk A., Zivkovic I., Schmidt R. Novel materials in magnetic resonance imaging: High permittivity ceramics, metamaterials, metasurfaces and artificial dielectrics. MAGMA. 2022;35:875–894. doi: 10.1007/s10334-022-01007-5. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 78.Wang G., Gong Y. Metamaterial lens applicator for microwave hyperthermia of breast cancer. Int. J. Hyperth. 2009;25:434–445. doi: 10.1080/02656730903061609. [DOI] [PubMed] [Google Scholar]
- 79.Schmidt R., Webb A. Metamaterial Combining Electric- and Magnetic-Dipole-Based Configurations for Unique Dual-Band Signal Enhancement in Ultrahigh-Field Magnetic Resonance Imaging. ACS Appl. Mater. Interfaces. 2017;9:34618–34624. doi: 10.1021/acsami.7b06949. [DOI] [PMC free article] [PubMed] [Google Scholar]
Associated Data
This section collects any data citations, data availability statements, or supplementary materials included in this article.
Supplementary Materials
Data Availability Statement
The data presented in this study are available on request from the corresponding author due to privacy reasons.