Skip to main content
Polymer Science & Technology logoLink to Polymer Science & Technology
. 2025 Apr 22;1(4):314–329. doi: 10.1021/polymscitech.5c00023

Models and Theories Regarding the Brittle-Ductile Transition of Rubber-Toughened Thermoplastics and Their Application in the Design of High-Impact Polymer Composites with Balanced Toughness and Rigidity

Yunbao Gao 1, Zonglin Jiang 1, Jianing Zhang 1, Haiying Tan 1, Jing Jin 1,*, Wei Jiang 1,*
PMCID: PMC13052713  PMID: 42254531

Abstract

Toughness and stiffness are two parameters that determine whether a polymer can be used as an engineering material. Therefore, polymer toughening and stiffening have been continuously attractive and important topics for both polymer science and engineering. The brittle-ductile transition (BDT) of a polymer plays an important and special role in high-impact polymer preparation and its application because the critical BDT point is the reference point for designing a ductile polymer and the limit point for its application as a ductile material. Moreover, the BDT point also determines the balance between the toughness and rigidity of toughened polymers. In this review, factors such as morphology, properties of the toughening particles and matrix polymer, temperature, and deformation speed that can affect the BDT of particle-toughened thermoplastics are first summarized. Subsequently, the model and theory concerning the relationships among these factors at the critical BDT point are systematically introduced in detail. Finally, recent progress in designing and preparing high-impact polymer composites with balanced toughness and rigidity on the basis of the model and theory of the brittle–ductile transition is introduced and discussed.

Keywords: polymer toughening, brittle−ductile transition, polymer stiffening, balanced toughness and stiffness, core-shell rubber particles


graphic file with name ps5c00023_0028.jpg


graphic file with name ps5c00023_0027.jpg

1. Introduction

With the development of polymer science and technology, an increasing number of polymeric materials have been used in automobiles, buildings, aviation, etc. Toughness is one of the most important mechanical properties that determines whether a polymer can be used as an engineering material. Therefore, polymer toughening has always been an attractive and important topic for polymer scientists and engineers since polymers have been used as engineering materials, and great progress has been made. Many papers, including numerous review articles and books on this topic − have been published. For example, Wu S3 reviewed the intrinsic brittle–ductile behavior of polymers and blends in terms of chemical structure, chemical composition, and chain structure, which can yield the ultimate toughness in both polymers and blends. Fu and Mai et al. discussed in detailed the effects of particle size, particle/matrix interface adhesion, and particle loading on the stiffness, strength, and toughness of particulate-polymer composites. Liang and Li reviewed rubber toughening in polypropylene (PP). Wang and Qiao et al. reviewed the advances in toughened polymer materials by structured rubber particles and discussed four categories of structured rubber toughening, including heterogeneous rubber microparticle toughening, oriented anisotropic rubber microparticle toughening, rubber nanoparticle toughening, and bimodal size distributed rubber particle toughening. More recently, Wee and Choi provided a detailed review of the ductile-to-brittle transition behavior and improvements in impact resistance observed in rubber-toughened PP blends.

Nevertheless, improving the toughness of a polymer generally compromises its rigidity. Taking PP as an example, PP with high toughness or high rigidity can be prepared, while PP with both high impact and high rigidity cannot. Figure shows the impact strength and flexural modulus of commercial PP collected from different suppliers. The area with impact strength >400 J/m and flexural modules >1500 MPa are empty, limiting their use in engineering. Therefore, increasing toughness without rigidity loss, even those with higher rigidity, has been a challenging topic for both polymer scientists and engineers, but great progress has been achieved in rubber-toughened thermoplastics. − All the above-mentioned results indicate that the balance between toughness and rigidity can be changed by modulating the composition and structure of toughening rubber particles. However, until now, review articles on models and theories for rubber-toughed thermoplastics and their correlations with balanced toughness and rigidity have not been available.

1.

1

Toughness and stiffness properties of commercial PP homo- and co-polymer products from different suppliers. All data were collected from their official website and at room temperature. Reprinted with permission from ref . Copyright 2022 Society of Plastics Engineers.

This review first summarizes the factors that can affect the brittle–ductile transition (BDT) of toughened rubber. Subsequently, the model and theory concerning the relationships among these factors at the critical BDT point are systematically introduced in detail. Finally, recent progress in designing and preparing high-impact polymer composites with balanced toughness and rigidity on the basis of the model and theory of BDT is introduced and discussed. The purpose of this study is to provide valuable insights into the development of advanced high-performing polymeric materials with excellent toughness and rigidity.

2. BDT of Rubber-Toughed Thermoplastics

As shown in Figure , many factors can induce a BDT. These include intrinsic factors such as the toughening particle size and its properties; the structure and properties of the thermoplastic matrix; and external factors such as the temperature, the tensile or impact speed. In this section, we introduce how these factors affect the BDT.

2.

2

A sketch diagram showing the BDT of a thermoplastic polymer.

Figure shows a sketch diagram of the BDT of a thermoplastic polymer. X i is a factor that can induce transitions, such as temperature, deformation speed, and toughening particle content. X ic is the critical transition point. The Y-axis represents the toughness that can be obtained via impact, tensile tests, etc. Figure can be divided into three zones: brittle, BDT, and ductile zones. In general, the external energy absorbed by a polymer during fracture originates from new surface generation, crazing, and yielding. For brittle fractures, new surface generation and crazing are two ways to absorb external energy. However, the energy absorbed by new surface generation is much lower than that generated by crazing. For ductile fracture, the polymer yields during fracture. The energy absorbed by yielding is much greater than that absorbed by crazing. It has been reported that 75% of the energy is absorbed by yielding for rubber particle-toughened nylon and PP − and that the fracture mode is changed during the brittle-to-ductile transition. In this review, we focus on the factors that can affect the BDT and their relationships at the critical transition point.

2.1. Effects of the Content and Size of Rubber Particles

Rubber or elastomer particles have been widely used to toughen thermoplastics. Generally, the toughness of toughened thermoplastics increases with increasing rubber or elastomer particle content (φ) up to a critical value (φ c ). Afterward, it increases sharply with increasing φ; i.e., a BDT occurs (as shown in Figure ). −

3.

3

Variation of Izod impact for elastomer-toughened nylon-66 and nylon-6, respectively, with elastomer content. Data for MMW nylon-6 and nylon-66 are from the refs and . Reprinted with permission from ref . Copyright 2004 Elsevier.

On the other hand, the size of rubber or elastomer particles is another key parameter that affects BDT. As shown in Figure , the impact strength changes very slowly with decreasing rubber size (d) up to a critical value (d c ) for a given rubber content. Thereafter, it increases sharply with decreasing d; i.e., a BDT takes place. The higher the rubber content is, the greater the d c value is. Here, if d is too small to be a stress center, then the rubber or elastomer particle has difficulty toughening thermoplastics effectively and inducing the BDT. ,,

4.

4

Notched Izod impact strength versus PR-rubber number-average particle diameter d n at constant adhesion Ga= 8100 J/m2 and constant rubber contents curve A: 10%; curve B: 15%; and curve C: 25% by weight. Solid symbols are for tough fracture; open symbols are for brittle fracture. Reprinted with permission from ref . Copyright 1985 Elsevier.

From Figure and Figure , it is evident that parameters d and φ affect the BDT. A notable report in this area was given by Wu in 1985. This scholar utilized a new parameter, i.e., the interparticle distance (ID), instead of d and φ and revealed that the BDT point only depended on the ID. If the ID is smaller than a critical interparticle distance (ID c ), then the fracture is ductile. Otherwise, it is brittle, which is independent of d and φ, as shown in Figure .

5.

5

Variation of the notched impact strength with ID. Reprinted with permission from ref . Copyright 1985 Elsevier.

The definition of ID can be obtained via eq :

ID=d[(kπ6φ)1/3−1] 1

where k is a constant depending on the spatial rubber/elastomer particle distribution (k = 1 for a cubic lattice, k = 2 for a body-centered cubic lattice), which indicates that the spatial packing of rubber particles in nylon/rubber blends is well described by a cubic lattice (k = 1). , A modified equation of eq was provided by Liu and Wang et al., in which the particle size distribution and particle configuration were considered.

Since Wu’s criterion was proposed, this topic has been extensively studied. In addition to nylon/rubber particle systems, it has been successfully used in PP, , PE, PS, PET, etc. systems. Here, we note that the transition studied by Wu resulted from the yielding of the matrix polymer during fracture. This means that Wu’s criterion can be applied to thermoplastic polymers rather than thermoset polymers. This is because thermoset polymers do not yield during fracture.

2.2. Effects of Rubber Mechanical Properties

As a toughening modifier, the mechanical properties of rubber or elastomer particles play an important role in the BDT. In the patents of Du Pont, , it is suggested that the modulus of the impact modifier must be one-tenth or less that of the nylon matrix to be effective in toughening nylon. This conclusion was further supported in nylon/rubber blends by the selection of different rubbers and elastomers in an experiment. The difficulty in this study is that it is impossible to ensure that the morphologies of the different nylon/rubber blends are the same and that the modulus of the selected rubber is exactly one-tenth that of the nylon. Recently, Yang and Jiang et al. studied the brittle–ductile transition in PP/poly­(ethylene-co-octene) (POE) elastomer blends by changing the impact test temperature. The advantage of this study is that the morphologies of a given PP/POE blend remain unchanged with temperature, and the modulus ratio of POE to PP can be well controlled by temperature. As shown in Figure , a clear, sharp transition induced by the modulus ratio of PP to POE can be observed for both the 20 and 24 wt % elastomer contents. The critical modulus ratio is near 1039, directly supporting the patents of Du Pont. , Here, we suggest that one-tenth or less of the matrix for rubber/elastomer particles is a necessary condition rather than a sufficient condition for effectively toughening thermoplastics. It also depends on the voiding ability and Poisson’s ratio for rubber or elastomer particles. ,

6.

6

Variation of the notched impact strength with the modulus ratio of PP to elastomer at −45, −35, −25 and −20 °C for different elastomer contents: (a) 20 wt % and (b) 24 wt %. Reprinted with permission from ref . Copyright 2022 The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.

2.3. Effects of Matrix Thermoplastics

The matrix material is a major component, and its molecular structure and properties certainly affect the BDT of its blend. The experimental results show that the value of ID c depends on the matrix polymer. This value is 0.15, 0.30, and 0.60 μm for PP/rubber, , nylon-66/rubber, and high-density polyethylene (HDPE)/rubber blends, respectively. The modifiers used in these studies are ethylene-propylene-diene monomer (EPDM) particles, and the specimens were tested via the same method (i.e., ASTM D-256) at room temperature. Therefore, the different values of ID c result from the difference in the properties of the matrix polymer.

Van der Wal and Gaymans et al. studied the effect of the matrix properties on the impact behavior of rubber-toughened PP. The matrix molecular weight was decreased by treating a high-molecular-weight PP-EPDM blend with peroxide to obtain a high matrix melt flow index (MFI), i.e., low-molecular-weight PP. The MFI of the blends ranged from 2 to 30 deg min–1. With decreasing matrix molecular weight, the brittle–ductile transition temperature (TBD) of the PP blends clearly increased, as shown in Figure .

7.

7

Notched Izod impact strength versus temperature for peroxide treated blends (15 vol %) with a weight-average diameter (D w) of approximately 0.4 μm. Matrix MFI (deg min–1): □, 1.8; ○, 12.9; ■, 29.2. Reprinted with permission from ref . Copyright 1998 Elsevier.

Recently, POE elastomer-toughened PP thermoplastics with different molecular weights were studied. The results showed that ID c increases considerably with increasing number-average molecular weight ( Mn® ) of PP. Moreover, further studies indicated that ID c depends on the molecular weight distribution (MWD) of PP. For the same Mn® of PP, the wider the MWD is, the larger the ID c of the composite. These results indicate that the molecular structure and properties of the matrix polymer directly affect the BDT of rubber-toughened thermoplastic polymers.

2.4. Effect of Interfacial Bonding between the Matrix and Rubber Particles

To study the effect of interfacial bonding between the nylon matrix and EPDM rubber, rubbers grafted with different amounts of maleic anhydride (MA) were prepared. The results showed that the minimum adhesion required was approximately 1000 J m–2, which is typical of van der Waals adhesion and provides sufficient adhesion for toughening.

Furthermore, Gaymans et al. prepared blends of 90 wt % nylon-6 and 10 wt % EPDM rubber. The MA grafted onto the rubber was found to react with the nylon during the blending process. The results showed that the concentration of the coupling agent, within the range 0.13–0.89 wt % grafted onto the rubber, has hardly any influence on either the dispersion process or the impact behavior of the blends, as shown in Figure . This further supports the conclusion that van der Waals adhesion between the two phases is sufficient for the toughening effect.

8.

8

Notched Izod impact strengths at 23 °C as functions of the weight-average rubber particle size for blends 1 to 12 (left); BT-temperature as functions of the weight-average rubber particle size for blends 1 to 12 (right). The symbols refer to the rubbers with different grafted MA degrees. The weight-average rubber particle size was determined from SEM. Reprinted with permission from ref . Copyright 1989 Elsevier.

2.5. Effects of Temperature, Deformation Speed, And Notch Tip Curvature

The effect of temperature on the ID c for EPDM rubber-toughened nylon was first reported by Borggreve and Gaymans et al., as shown in Figure . The ID c increases nonlinearly with increasing temperature and tends to be infinite at higher temperatures. A similar result was also obtained for EPDM rubber-toughened PP.

9.

9

ID c versus the brittle-tough temperature: ○, blend A; □, blend B; ●, blend C. Reprinted with permission from ref . Copyright 1987 Elsevier.

To investigate the effect of deformation speed, the tensile fracture energy of PP/EPDM rubber blends containing various EPDM contents was studied by changing the tensile speed. Figure shows that decreasing tensile speed can facilitate the BDT of the PP/EPDM. These results indicate that increasing the temperature and decreasing the deformation speed have equivalent effects on the BDT. With respect to the effect of the notch tips, sharper tips can lead to more significant deformation at the tip zone under the same test conditions. Therefore, the effect of the curvature of the notch tip results from the deformation speed; i.e., a larger curvature indicates a higher deformation speed under the same test conditions and thereby affects the ductile-brittle transition.

10.

10

Variation of fracture energy with tensile speed for PP/EPDM blend. Reprinted with permission from ref . Copyright 2000 Elsevier.

3. Model and Theory

To formulate the BDT of rubber or elastomer particle-toughened thermoplastic polymers, various models and theories have been proposed. First, Margolina and Wu proposed a percolation model. Specifically, if matrix ligaments (also named ID, as shown in Figure ) are thinner than a critical value, then a plane-strain-to-plane-stress transition and yielding take place. The onset of the transition obeys an appropriate scaling law with a mechanical critical exponent of 0.45, as shown in Figure . This can be recast as the percolation of spherical “stress volumes” in the random lattice. Each stress volume centers at a rubber particle with diameter d and includes a concentric annular shell of the matrix of constant thickness. The diameter of the stress volume equals to d + ID. During tough fracture, the stress volumes will yield and propagate. Interestingly, this is practically equal to the classical critical exponent β ≈ 0.44 in three dimensions. Similar results were obtained for PP/EPDM blends by Qi and Zheng. This model and theory provide a clear physical image and good interpretation of the BDT of rubber/elastomer particle-toughened thermoplastics. However, it cannot explain why the ID c depends on temperature, as shown in Figure . Given this, Margolina provided the following empirical formula:

IDc=0.16+0.003T(μm) 2

This formula fits the experimental results given in Figure in the lower temperature region; however, it does not fit the results in the higher temperature region.

11.

11

Log G versus log­(Φ s – Φ sc) for nylon/rubber blends, showing g = 0.45 + 0.06. Open squares are the data in the tough region. Filled squares are the estimated “tough” strength in the brittle region. Open circles are the brittle strength in the brittle region. The tough strengths in both tough and brittle regions are used to obtain correlation and the g value. The brittle strengths are plotted for reference only and are not used. (Φ s, the volume fraction of stress volumes; Φ sc, the critical volume fraction of stress volumes.) Reprinted with permission from ref . Copyright 1988 Elsevier.

Meijer and coworkers proposed a model based on an energy criterion to explain the occurrence of a critical material ligament thickness d 1, namely, ID c , as shown in Figure . The stored elastic energy per ligament can be considered to be correlated with the volume of matrix material that is relieved from elastic stress if a brittle fracture occurs. The matrix volume between two holes, that is, the shaded area in Figure a (direction 1 is the direction of the applied stress), can be estimated to be a sphere, with a diameter of d 1 (=h).

12.

12

Schematic view of a matrix ligament between two holes, representing non-adhering rubbery particles: (a) before plastic deformation and (b) during plastic deformation. The shaded area represents the elastically deformed volume that is relieved from elastic stress once the fibril breaks. Reprinted with permission from ref . Copyright 1993 Elsevier.

The maximum average stress in this volume is estimated to be the yield stress σ y , resulting in ductile plastic deformation of the matrix ligament, and the critical material ligament thickness d 1, i.e., the ID c , can be expressed as follows.

IDc=6(γ+k1ν1/2)E1k2ν−1/2σy2 3

where γ is the van der Waals surface energy, ν is the entanglement density, E 1 represents Young’s modulus, σ y is the yield stress of the polymer matrix, and k 1 and k 2 are two constants. From eq , it is known that ID c is the function of σ y and decreases considerably with increasing σ y . Combining eq and the well-known Eyring theory of viscosity given in eq , the calculated results (Figure ) show that the ID c increases nonlinearly with increasing temperature and decreasing strain rate, which is consistent with the experimental results.

γ̇=AE⁡exp[−(ΔG−Vσy)RT] 4

where γ̇ is the strain rate, A E is a constant, R is the gas constant, T is the absolute temperature, ΔG and V are the activation energy and activation volume of the matrix polymer, respectively.

13.

13

Model prediction of the ID c of EPDM rubber particle-toughened polycarbonate. Reprinted with permission from ref . Copyright 1994 Elsevier.

Corté and Leibler presented a model based on a stress criterion to explain the occurrence of a critical material ligament thickness, as shown in Figure . Toughening is successfully achieved if the initial ligament thickness L (i.e., ID) is smaller than the critical confinement length L c (i.e., ID c ) given by eq .

IDc=ξ*+d(CσBσy)2 5

where σ y and σ B are the tensile yield stress and the tensile stress at break, respectively; d is the rubber particle size; ξ* is the mean distance between microcracks; and C is a dimensionless factor that should depend on the ability of the particles to release stress and the criterion for brittle stress. This indicates that ID c depends on the particle size d and the mechanical properties, including σ y and σ B of the matrix polymer. Moreover, ID c changes by σ y –2, which includes eq given by Meijer et al.

14.

14

(a) Stress distribution in front of a notch submitted to a remote tensile stress σ 1. (b) Stress state in the process zone where triaxial stresses are the greatest. (c) Local stress distribution around voided particles. (d) Schematic representation of the deformation processes in toughened systems: yielded regions (dark gray) grow around particles while cracks open in the elastic matrix far from the particles. Reprinted with permission from ref . Copyright 2007 American Chemical Society.

In addition, experimental studies for rubber-modified polyamides showed that in tough samples the crystalline orientation in the interparticle region is of a distinctly different character. The lamellae are organized perpendicular to the rubber-matrix interface, while the hydrogen-bonded planes of low slip resistance are aligned parallel to these interfaces. Based on this observation a model is proposed to elucidate the deformation and toughening mechanisms of these materials. According to this model, the yield stress should be lowered in regions of easy shear. This local softening should then reduce the overall flow stress of the material allowing it to deform to large strains without initiating any critical fracture process, thus enhancing its toughness. A similar phenomenon (i.e., the crystallites are mostly oriented) was observed in rubber-toughened HDPE films.

On the other hand, the internal cavitation of particles and its ability paly important role in polymer toughening, which depends on the particle size and its properties. It is demonstrated that maximum toughness is achieved when the particles are large enough to cavitate a long way ahead of a notch or crack tip, but not so large as to initiate unstable crazes and thus reduce fracture resistance. , Borggreve et al. found that the impact toughness of an elastomer modified polyamide with given matrix structure and specimen geometry depends on the stress at which rubber particle cavitation or delamination in hydrostatic tension occurs and suggested that both a low elastic modulus and a high Poisson’s ratio of the elastomer favors voiding within the composite.

The above models and theories can be used to interpret the effects of morphology (ID, d), temperature, strain rate, and properties of the matrix polymer on the BDT. However, the use of toughening modifiers as the main component was not considered in these models and theories. Jiang et al. reported that the volumes around rubber/elastomer particles are stressed when an external force is applied to the sample and that the onset of the first-path connectivity (percolation) of these stressed volumes results in the occurrence of the BDT. Here, the stressed volumes percolated first regardless of the number of particles, as shown in Figure , and then the yielding of the stressed volumes was studied. In this model and theory, all the particles are considered to be the same size, the interactions among the dispersed particles are ignored, and combined with the Eyring theory, i.e., eq , the following equations are obtained:

IDc=[Aσyεy]1/3−d 6

where ε y is the yield strain of the matrix thermoplastic, d is the average dispersed particle diameter, and A is a parameter related to the strain energy, E, of the matrix.

IDc=[QE(TBTm−T)2+d3]1/3−d 7
TBT=TBTm−QE(ID+d)3−d3 8

where T BT is the BDT temperature of the rubber/elastomer particle-toughened thermoplastics, T BT and Q are given as follows:

TBTm=ΔGRIn(B/γ̇) 9
Q=12M1V2πR2[In(B/γ̇)]2 10

where B is a constant, M 1 is the modulus of the matrix polymer, γ̇ is the strain rate, R is the gas constant, ΔG and V are the activation energy and activation volume of the matrix polymer, respectively. Equation indicates that ID c tends to infinity if T is close to T BT , which means that the rubber content is zero. Therefore, T BT is the T BT of the matrix polymer itself.

15.

15

Schematic of the onset of first-path connectivity of the stressed volumes for different rubber/elastomer contents. Reprinted with permission from ref . Copyright 1998 Elsevier.

Equation shows that in addition to the yield stress of the matrix thermoplastic σ y , the yield strain ε y is also a key parameter that affects the BDT. It is the product of the yield stress and yield strain of matrix polymer that determines the BDT of toughened thermoplastic polymers. The higher the product of the yield stress and the yield strain of the matrix polymer is, the smaller the ID c of the blends is. For the nylon/rubber blends, although the yield stress (82 MPa) of nylon-66 is greater than that (31 MPa) of PP, its yield strain (5%) is much lower than that (15%) of PP. Therefore, the ID c (0.15 μm) of the PP/rubber blends was lower than that (0.30 μm) of the nylon-66/rubber blends. For the HDPE/rubber blends, because of the product of the yield stress (24.9 MPa) and yield strain (approximately 3.3%) of the HDPE, its ID c (0.60 μm) is larger than that (0.30 μm) of the nylon-66/rubber blends. Notably, the results for these blends are comparable because the same test method (ASTM D638), test temperature (room temperature), and rubber (EPDM) were used.

From eq , it is known that ID c is a function of d. By performing a Taylor series expansion for eq and taking the first-order approximation in the case of T ≪ T BT , ID c increases linearly and is independent of d. Therefore, Margolina’s empirical formula given in eq is the first-order approximation result of eq , and Wu’s criterion, i.e., ID c , is independent of d and φ, and is applicable in the low-temperature region, i.e., T ≪ T BT . Notably, from this equation, compared with individual T BT or T, T BT – T is a more universal parameter that determines the BDT. In other words, the curves of ID c versus T for different T BT values can be reduced to a master curve that is independent of T BT , namely, a matrix material for the same toughening rubber and test conditions. This finding is consistent with the experimental results shown in Figure . This figure shows that the two separated curves of ID c versus T (Figure A) are reduced to a master curve (Figure B) for the PP/EPDM and nylon/EPDM rubber blends in the same impact test. The results indicate that T BT – T is a universal parameter that determines the BDT. Further study suggests that 1 – T/T BT is more universal than T BT – T is.

16.

16

(A) ID c versus T for nylon/EPDM and PP/EPDM blends, in which T BT = 74 °C for nylon and T BT = 115 °C for PP; (B) ID c versus T BT – T. (Authors note: T g in ref corresponds to T BT .) Reprinted with permission from refs and . Copyrights 1987 and 1998 Elsevier.

Moreover, from eq , ID c increases with decreasing T BT . Equations and indicate that increasing the strain rate γ̇ can lead to an increase in T BT . This means that ID c increases with decreasing γ̇ or increasing curvature of the notch tip (a large curvature indicates a higher strain rate under the same test conditions) as observed in previous experiments. In addition, from eqs and , T BT increases with the increasing activation energy ΔG of the matrix. Adding a plasticizer to a polymer can reduce its ΔG, resulting in a decrease in T BT . From eqs and , it is known that ID c increases, whereas T BT decreases with the addition of a plasticizer into the thermoplastic matrix. Water is a suitable plasticizer for nylon. Therefore, this can explain why ID c increases with increasing water content in nylon for the nylon/EPDM rubber blend.

From eq , the dependence of T BT on T BT and ID is clearly indicated. Moreover, the effect of rubber/elastomer particles on T BT can be studied by using the relationship between T BT and E. Here, E is the matrix strain energy in the stressed volume around a rubber/elastomer particle, and the stress analysis is given in Figure . E can be obtained via the following integration:

E=∫VshellWsdV=2π∫d/2ID/2∫0πWsr2sin⁡θdrdθ 11

where V shell refers to the integral region (the spherical shell of the matrix from d/2 to ID/2 in the stressed volume) and W s is the strain energy density in the matrix, which is defined as ,

Ws=(12M1)[σ12+σ22+σ32+2v1(σ1σ2+σ1σ3+σ2σ3)] 12

where σ 1, σ 2 and σ 3 are the three principal stresses, M 1 and v 1 are the Young’s modulus and Poisson’s ratio of the matrix polymer, respectively. The three principal stresses can be written as follows:

σ1=12(σ1rr+σ1θθ)+12(σ1rr−σ1θθ)2−4(σ1rθ)2 13
σ2=12(σ1rr+σ1θθ)−12(σ1rr−σ1θθ)2+4(σ1rθ)2 14
σ3=σ1φφ 15

where σ 1 , σ 1 , σ 1 and σ 1 are the stresses inside the composites containing spherical inclusions (rubber/elastomer particles), as shown in Figure .

17.

17

Stress analysis for the model of composites containing spherical inclusion. Reprinted with permission from ref . Copyright 2001 Elsevier.

To perform quantitative calculations, it was assumed that both the matrix material and the rubber or elastomer particles are homogeneous, isotropic, linear elastic, and have perfect adhesion between the elastomer and the matrix. From Goodier’s equations, the stresses can be given as follows:

σ1rr=2{2Ar3−2v11−2v1Cr3+12Br5+[−2(5−v1)1−2v1Cr3+36Br5]⁡cos⁡2θ}σ1θθ=2{−Ar3−2v11−2v1Cr3−3Br5+[Cr3−21Br5]⁡cos⁡2θ}σ1φφ=2{−Ar3−2(1−v1)1−2v1Cr3−9Br5+[3Cr3−15Br5]⁡cos⁡2θ}σ1rθ=2{−2(1+v1)1−2v1Cr3+24Br5}⁡sin⁡2θ 16
A(d/2)3=−F8n−1(7−5v1)n+(8−10v1)×2n(1−2v2)(6−5v1)+(3+19v2−20v1v2)2n(1−2v2)+(1+v2)+F4[(1−v1)1+v21+v1−v2]−n(1−2v2)2n(1−2v2)+(1+v2)B(d/2)5=F8n−1n(7−5v1)+(8−10v1)C(d/2)5=F85(1−2v1)(n−1)n(7−5v1)+(8−10v1) 17

where n is the ratio of the shear modulus (G 1) of the matrix to that (G 2) of the elastomer (i.e., n = G 1/G 2), ν1 and ν2 are Poisson’s ratios for the matrix and elastomer, respectively, F is the applied uniaxial tension, and r is the radius from the center of the inclusion. The superscripts represent tensorial notation. The calculation result obtained by combining eq with eqs – is given in Figure . It is evident T BT decreases very rapidly with increasing G 1 /G 2 (namely, the modulus of the rubber/elastomer decreases if the modulus of the polymer matrix remains unchanged) up to 10; thereafter, T BT decreases very slowly with increasing G 1 /G 2 . These results suggest that the modulus of the elastomer must be less than one-tenth that of the matrix. Otherwise, the BDT will be relatively high, and the blend will be brittle at low temperatures for elastomer toughening thermoplastics. This conclusion is in agreement with the experimental results introduced above. −

18.

18

G 1/G 2 dependence of T BT of the blend with ID = 0.30 μm, d = 0.30 μm, T BT m = 74 °C. Reprinted with permission from ref . Copyright 2001 Elsevier.

The above models and theories do not show an apparent relationship between the molecular weight of the matrix polymer and the BDT. However, from eq , ID c directly depends on σ B of the matrix thermoplastic, which is a function of molecular weight as follows given by Flory:

σB=A−BMn® 18

where A and B are constants, and Mn® is the number-average molecular weight. Here, σ B is the tensile stress at break, which occurs before the yielding of a thermoplastic polymer; i.e., it is a brittle fracture stress. Equations and indicate that ID c increases with increasing Mn® of the thermoplastic matrix, which is in agreement with the experimental results.

In addition, from eqs and , clearly, ID c decreases with increasing T BT of the matrix polymer itself, i.e., T BT , whereas the brittle–ductile transition temperature T BT increases with increasing T BT . The experimental results showed that T BT increased with increasing PP crystallinity for PP/rubber blends. This leads to an increase in T BT , which is consistent with the theoretical prediction.

4. Application in the Design of High-Impact Polymer Composites with Balanced Toughness and Rigidity

The rigidity of rubber or elastomers is generally lower than that of thermoplastic polymers. Therefore, the introduction of rubber or elastomers into thermoplastics can lead to a decrease in rigidity, more or less depending on the rubber or elastomer content added and moduli. As shown in Figure , when 15 wt % POE is added to PP, the impact strength increases from 5 to 37 kJ/m2, whereas the tensile modulus decreases from 1060 to 670 MPa, which is 36.8% less than that of pure PP.

19.

19

Variation of impact strength with tensile modulus of PP/POE blends. Reprinted with permission from ref . Copyright 2016 John Wiley and Sons.

From Figure , it is clear that a lower rubber or elastomer content is beneficial to rigidity. However, to ensure that the fracture is ductile, the rubber or elastomer content must be higher than the critical value, i.e., φ c . Therefore, toughening thermoplastics with less rigidity loss or even higher rigidity is always a challenging and attractive topic for both polymer scientists and engineers. − In fact, by combining the model and theory of BDT with elastic mechanics, this topic can be quantitatively studied, and new strategies can be generated.

In general, the modulus (E c ) for materials with multiphase structures is a function of the modulus and volume fraction of each phase, φ i and E di , as follows:

EC=f(φ1,Ed1···φi,Edi···φn,Edn) 19

where φ i and E di are the volume fraction and modulus of each phase, respectively, and 1 ≤ i ≤ n (n is the total number of phases). Notably, the variation in the parameters in eq must be limited to ensure that the fracture is ductile. The critical BDT point is the limit point for ductile fracture of rubber- or elastomer-toughened thermoplastics. All parameters (...X i ...) including φ i and E di E at the critical point depend on each other, as given in part 3, and can be mathematically simplified as follows:

F(X1,X2,···Xi···)|at critical point=0 20

where F refers a function and eq means all parameters (...X i ...) depend each other at critical point. The balance between toughness and rigidity for rubber/elastomer particles toughened into thermoplastics can be studied by combining eqs and .

4.1. Toughening Thermoplastics with One-Phase Rubber Particles

A one-phase modifier means that the structure and properties of the rubber/elastomer are homogeneous and uniform. When the matrix thermoplastic polymer also has one phase, the total number of phases (n) is 2 for the composites, i.e., the matrix phase and rubber phase. To quantitatively study the modulus of such particles, toughened thermoplastic polymers can be simplified to a two-phase model, i.e., Takayanagi’s model, as shown in Figure , by which the relative modulus E c /E m can be obtained:

EcsEm=(1−φ+φ1−φ+φEdEm)−1 21

where E m is the modulus of the matrix thermoplastic polymer and E d and φ are the modulus and content (volume fraction) of rubber/elastomer, respectively. The calculated results from eq are given in Figure . As expected, the modulus decreases with increasing φ and decreasing E d /E m when E d /E m < 1.

20.

20

(a) Schematic representation of the two-phase model. (b) The equivalent model (connection in series). Reprinted with permission from ref . Copyright 2019 Elsevier.

21.

21

Variation of E c /E m with φ for different E d /E m . 0.225 is the critical rubber volume fraction (φ c ) and the shadow part is the ductile region for rubber-toughened PP composites. Reprinted with permission from ref . Copyright 2019 Elsevier.

Figure shows that decreasing φ or increasing E d is beneficial for increasing the modulus. However, to ensure that the fracture is ductile, φ > φ c and E d /E m < 1/10 are necessary, as discussed above. Taking typical rubber-toughened PP as an example, φ c is 0.225. Figure shows that the two boundaries, i.e., E d /E m = 0 and E d /E m = 1/10, are close to each other. This indicates that changing the rubber or elastomer modulus has less of an effect on the modulus in the ductile region. However, decreasing the critical rubber/elastomer volume fraction φ c is an effective way to decrease the modulus loss. Via eqs , , and , decreasing the rubber or elastomer particle size d, increasing the tensile stress at break σ B , and decreasing the tensile yield strain ε y of the matrix polymer can lead to a decrease in the BDT with decreasing rubber or elastomer content. This is beneficial for deceasing the loss of rigidity.

4.2. Toughening Thermoplastics with Core-Shell Rubber Particles (CSRP)

In addition to one-phase (homogeneous) rubber particles, multiphase (heterogeneous) rubber particles have also been used to toughen thermoplastic polymers. Among these particles, CSRP, which consist of two different materials, have been widely used as effective toughening modifier particles and can be obtained by melting blending or alloying in a reactor. ,− The PP alloys in the reactor, also referred to as impact copolymer polypropylene (ICP), and high-impact polypropylene (HIPP), are produced via two-step polymerization (TSP), , which is bulk polymerization of propylene and subsequent gas-phase copolymerization of ethylene and propylene; these alloys exhibit an excellent toughness. − This is attributed to their compositional heterogeneity and unique core-shell structure. − Yang et al. , characterized the phase morphology of HIPP and reported that dispersed phase particles were uniformly distributed in the HIPP matrix film with a diameter of approximately 0.5–2.0 μm and exhibited a multilayer core-shell structure, which was composed of an inner core (PE crystallization), an intermediate layer (ethylene propylene rubber (EPR) phase) and an outer shell (PE crystallization). Su et al. , also confirmed the existence of core-shell structure in HIPP alloys and reported that the inner core could be a crystalline PP or crystalline PE, and that the intermediate layer was an EPR phase. Moreover, Yin et al. , studied the influence of a dispersed phase with the core-shell structure on the mechanical properties and phase morphology of polyamide-6 (PA6) /EPDM-g-MA/HDPE ternary blends. These researchers revealed that low-viscosity HDPE formed single-core core-shell structures. However, high-viscosity HDPE results in multinuclear core-shell structures, and the fibrillation of core-shell particles in ternary blends (such as particle bridges) can absorb fracture impact energy and prevent microcracks from further propagating. Thus, the impact strength of the blends is considerably increased. Fu et al. reported that incorporating small amounts of poly­(d-lactide) (PDLA) into polylactide/core-shell rubber (PLA/CSR) blends induce the networking of the CSRP in the PLA matrix and that the formation of this network-like structure can remarkably improve the impact toughness without sacrificing the composite stiffness. Zheng et al. studied the morphologies and properties of PP/EPR/HDPE ternary blends and found that the ternary blends presented a notable improvement in toughness with less rigidity loss. This can be attributed to the particular core-shell structure with an HDPE core encapsulated in the EPR shell. More recently, Bao and Jiang et al. revealed that EPR-PE core-shell formation in a PP matrix depended on the PE chain structure and viscosity.

For core-shell particles toughened with thermoplastic polymers, the total phase number is 3 (n = 3), i.e., the matrix, shell, and core phases. The CSRP-toughened thermoplastic is depicted in Figure (a). It can be converted to a three-phase model , for modulus calculation, as shown in Figure (b). When longitudinal stress is applied, the equivalent three-phase model can be reduced to three regions in series connected by 1, 2, and 3, as shown in Figure (c), by which the relative modulus E c /E m can be obtained as follows:

EcsEm=(1−α+α−μ(1−β)+βEsEm+μ(1−β)+(β−λ)EsEm+λEdEm)−1 22

where E c is the modulus of core-shell particle toughed thermoplastic, and E m , E s and E d are the moduli of the matrix thermoplastic, shell phase and core phase, respectively. The area fraction for each phase given in Figure b corresponds to its volume fraction. Therefore, λμ = φ cs and αβ = φ d , where φ cs and φ d are the volume fractions for the core-shell particles and core phase, respectively. If the system is isotropic, then λ = μ and α = β exist; therefore, λ2 = φ cs and β 2 = φ h .

22.

22

Schematic of (a) CSRP-toughened polymer composites and (b) its equivalent three-phase model for modulus and (c) tensile modulus (connection in series). Reprinted with permission from ref . Copyright 2020 Elsevier.

On the other hand, as mentioned above, the variations in the parameters in eq must be limited by eq to ensure that the fracture is ductile. For CSRP, its volume fraction φ cs must be greater than a critical value, and as an effective toughening modifier, its modulus of the matrix thermoplastic E cs /E m must be lower than 1/10. It can be obtained by a two-phase model (series) as given in the eq :

EcsEm=(1−φdEsEm+φd(1−φd)EsEm+φdEdEm)−1 23

where φ d is the volume fraction of the core in the CSRP. This parameter depends on the core-shell particle diameter D and core diameter d, i.e., φ d = d 3/D 3. If the shell thickness is t, then D = 2t + d. Adding the limitation of E cs /E m = 1/10 into eq , the following relation can be obtained.

EcsEm=(1−φdEsEm+φd(1−φd)EsEm+φdEdEm)−1=1/10 24

Via eqs and , the balance between toughness and rigidity for CSRP-toughened thermoplastics can be studied, and the optimized structure and properties of the CSRP can be determined. The variation in the relative modulus E c /E m with E d /E m for different shell moduli at the critical BDT point is shown in Figure . E c /E m increases considerably with increasing core modulus and decreasing shell modulus. That is, a CSRP with a harder core and softer shell, is beneficial for the balance between toughness and rigidity. EPR rubber was used as the shell, and PP was used as the matrix polymer (E s /E m = 1/100), with PE (E d /E m = 3/5) and PP (E d /E m = 1) remaining unchanged. As indicated in Figure , 13.5% modulus loss is the lowest value for the CSRP-toughened PP in theory, which is consistent with the experimental results for the core (PE)-shell (EPR rubber) particle-toughened PP. However, a 5.4% modulus loss is the lowest value for CSRP-toughened PP in theory for E d /E m ≤1. These results indicate that the PP core is more beneficial for increasing stiffness than the PE core is. These two values are smaller than 26.1%, which is the lowest modulus loss for one-phase modifier-toughened PP. Su et al. , investigated the structure and composition of phase domains in two different commercial HIPP alloys via atomic force microscopy-infrared (AFM-IR) spectroscope. The results revealed that the notch impact strength and flexural modulus are 609.6 J/m and 1100 MPa, respectively, for the PP core-EPR shell rubber particles-toughed PP and 584.9 J/m and 953 MPa, respectively, for the PE core-EPR shell rubber particle-toughed PP, which is consistent with the theoretical results shown in Figure .

23.

23

Relative modulus E c /E m for different CSRP (PP core and PE core), where the green line is for typical EPR, φ cs = 0.225. Reprinted with permission from ref . Copyright 2020 Elsevier.

4.3. Preparation of Toughened Thermoplastics with High Toughness and High Rigidity

In previous experimental work, significant improvements in impact strength were obtained by tailoring the microstructures of PP/elastomer/microsilica composites. , This means that toughness and rigidity can be improved simultaneously. In theory, as shown in Figure , the relative number of CSRP-toughened thermoplastic modulus increases with increasing number of core modulus. The next question is whether it can be greater than 1 if the core modulus is continuously increased, which means that the toughness and rigidity can be improved simultaneously without conflicts. Under the premise of ensuring that the core-shell particle can act as an effective impact modifier, i.e., E cs /E m = 1/10, the calculation results via eqs and are given in Figure . The results indicate E c /E m increases rapidly with increasing E d /E m up to 20; thereafter, it increases slowly, and reaches 1.81 when E d /E m = 90. This means that toughness and rigidity can be improved simultaneously in theory.

24.

24

E c /E m as a function of E s /E m for E cs /E m = 1/10, φ cs = 0.225, φ d = 96.38%. Reprinted with permission from ref . Copyright 2024 American Chemical Society.

Considering PP as the matrix, POE elastomer as the shell (E s /E m = 1/300), and silicon dioxide (SiO2) particle (E d /E m = 90) as the core, the calculation results are shown in Figure A. It is revealed that E c /E m increases as φ cs increases to a peak value; thereafter, it decreases continuously. Furthermore, increasing the content of hard-core SiO2 can lead to an increase in E c /E m . Notably, the peak position moves toward higher values of φ cs as the SiO2 content increases. These results indicate that the overall core-shell particle content should be optimized to achieve the highest composite modulus. All these theoretical results were supported by the experimental results, as shown in Figure B. On the other hand, φ cs must be greater than a critical value to ensure that the toughened thermoplastics is ductile.

25.

25

Variation of E c /E m with φ cs for POE-SiO2 core-shell particle-toughened PP with different POE and SiO2 ratios. (A) Theoretical results. (B) Experimental results. Reprinted with permission from ref . Copyright 2024 American Chemical Society.

According to the above theoretical analysis, to prepare toughened thermoplastics with impact and higher rigidity, the content of SiO2 in the core-shell particles should be as high as possible under the premise of ensuring that the core-shell particles can act as effective impact modifiers. The experimental results are shown in Figure . The notch impact strength and flexural modulus of the toughened PP can reach 44.6 kJ/m2, which is 5.4 times greater than that of the PP, and 1.6 GPa, which is 1.4 times greater than that of the PP. Here we like to mention that pure rigid particles can be used to toughened thermoplastic polymers. ,, However, comparing with core-shell rubber particles toughening, high-impact toughness (>40 kJ/m2) can be obtained only for some special thermoplastic polymers such as PE , or PP with very high molecular weight (M w, 657 000 g/mol).

26.

26

Toughness and stiffness properties of PP/SiO2/POE composites. Reprinted with permission from ref . Copyright 2024 American Chemical Society.

5. Summary and Perspective

Toughening thermoplastics with rubber or elastomer particles is one of the most common and effective ways to manufacture high-impact thermoplastic composites. The critical BDT point is not only a reference point for designing ductile thermoplastic composites but also a limit point for a thermoplastic composite to be used as a ductile material. At this point, all the factors that can induce BDT depend on each other. Previously, the dependence of these factors has been extensively studied, and great progress has been achieved. However, a comprehensive and systematic summary that takes all these factors into account is needed. For this purpose, internal factors such as the structure and properties of the matrix thermoplastics and toughness modifier and external factors such as temperature and deformation speed are included, and their dependencies at critical BDT points are given in this review. We focus on the models and theories and their correlation as well as application scope.

On the other hand, an improvement in toughness generally leads to a decrease in rigidity. Obtaining ductile thermoplastics with less loss of rigidity (even those with higher rigidity), has been a major challenge for polymer scientists and engineers. Combining the models and theories of elastic mechanics, it was proposed that a CSRP with a hard core is beneficial for balancing toughness and rigidity. Through this strategy, high-impact and high-rigidity thermoplastic composites can be obtained. Recent works on this topic are reviewed and discussed in this article.

Finally, it is known that viscosity is quite important for polymer processing. Gaymans studied the toughening of PP with calcium carbonate particles and reported that complete ductile fractures can be obtained at room temperature (50–60 kJ/m2) when the modulus can be exceed 2000 MPa. However, the viscosity of the PP used is extremely low (MFI is as low as 0.03 g/min). A polymer material with a high MFI, high toughness, and high rigidity is an attractive yet highly challenging topic. For example, PP and its composite with high toughness (notch impact strength >40 kJ/m2), high rigidity (flexural modulus >1.5 GPa), and high MFI (MFI > 10 g/10 min 230 °C, 2.16 kg) have not been obtained until now. This “three high” PP can considerably widen its application area and is the next goal for polymer scientists and engineers working on high-performance polymer manufacturing.

Acknowledgments

This work was financially supported by the National Natural Science Foundation of China for General Program (22373099).

Glossary

Abbreviations

PP

polypropylene

ID

interparticle distance

ID c

critical interparticle distance

PE

polyethylene

PS

polystyrene

PET

polyethylene terephthalate

POE

poly­(ethylene-co-octene)

HDPE

high-density polyethylene

EPDM

ethylene-propylene-diene monomer

ASTM

American society of testing materials

D w

weight-average diameter

MFI

melt flow index

MWD

molecular weight distribution

Mn®

number-average molecular weight

MA

maleic anhydride

T

temperature

BDT

brittle–ductile transition

ΔG

the activation energy of matrix polymer

T BT

brittle–ductile transition temperature

ν

Poisson’s ratio

ICP

impact copolymer polypropylene

HIPP

high-impact polypropylene

TSP

two-step polymerization

EPR

ethylene propylene rubber

PA6

polyamide-6

PDLA

poly­(d-lactide)

PLA

polylactide

CSR

core-shell rubber

CSRP

core-shell rubber particles

AFM-IR

atomic force microscopy-infrared

SiO2

silicon dioxide

The authors declare no competing financial interest.

References

  1. Bucknall, C. B. Toughened plastics; Springer, 1977. [Google Scholar]
  2. Kinloch, A. J. Fracture behaviour of polymers; Springer Science & Business Media, 2013. [Google Scholar]
  3. Wu S.. Control of intrinsic brittleness and toughness of polymers and blends by chemical structure: a review. Polym. Int. 1992;29(3):229–247. doi: 10.1002/pi.4990290313. [DOI] [Google Scholar]
  4. Perkins W. G.. Polymer toughness and impact resistance. Polym. Eng. Sci. 1999;39(12):2445–2460. doi: 10.1002/pen.11632. [DOI] [Google Scholar]
  5. Liang J., Li R.. Rubber toughening in polypropylene: A review. J. Appl. Polym. Sci. 2000;77(2):409–417. doi: 10.1002/(SICI)1097-4628(20000711)77:2<409::AID-APP18>3.0.CO;2-N. [DOI] [Google Scholar]
  6. Wang J., Zhang X., Jiang L., Qiao J.. Advances in toughened polymer materials by structured rubber particles. Prog. Polym. Sci. 2019;98:101160. doi: 10.1016/j.progpolymsci.2019.101160. [DOI] [Google Scholar]
  7. Argon A., Cohen R.. Toughenability of polymers. Polymer. 2003;44(19):6013–6032. doi: 10.1016/S0032-3861(03)00546-9. [DOI] [Google Scholar]
  8. Wee J. W., Chudnovsky A., Choi B. H.. Brittle-ductile transitions of rubber toughened polypropylene blends: a review. Int. J. Precis. Eng. Man-GT. 2024;11(4):1361–1402. doi: 10.1007/s40684-023-00581-w. [DOI] [Google Scholar]
  9. Fu S., Feng X., Lauke B., Mai Y.. Effects of particle size, particle/matrix interface adhesion and particle loading on mechanical properties of particulate-polymer composites. Compos. Part. B: Eng. 2008;39(6):933–961. doi: 10.1016/j.compositesb.2008.01.002. [DOI] [Google Scholar]
  10. Bartczak, Z. ; Galeski, A. . Mechanical Properties of Polymer Blends. In Polymer Blends Handbook; Utracki, L. A. , Wilkie, C. A. , Eds.; Springer Netherlands, 2014; pp 1203–1297. [Google Scholar]
  11. Li F., Zhang N., Gao Y., Yan N., Jin J., Su Z., Jiang W.. In situ formation of core-shell rubber particles in polypropylene matrix by melt blending and its effects on the toughness and stiffness of the composites. Polym. Eng. Sci. 2022;62(12):4090–4099. doi: 10.1002/pen.26169. [DOI] [Google Scholar]
  12. Corte L., Rebizant V., Hochstetter G., Tournilhac F., Leibler L.. Toughening with little stiffness loss: polyamide filled with ABC triblock copolymers. Macromolecules. 2006;39(26):9365–9374. doi: 10.1021/ma061090g. [DOI] [Google Scholar]
  13. Wang X., Peng S., Chen H., Yu X., Zhao X.. Mechanical properties, rheological behaviors, and phase morphologies of high-toughness PLA/PBAT blends by in-situ reactive compatibilization. Compos. Part. B: Eng. 2019;173:107028. doi: 10.1016/j.compositesb.2019.107028. [DOI] [Google Scholar]
  14. Yang H., Zhang Q., Guo M., Wang C., Du R., Fu Q.. Study on the phase structures and toughening mechanism in PP/EPDM/SiO2 ternary composites. Polymer. 2006;47(6):2106–2115. doi: 10.1016/j.polymer.2006.01.076. [DOI] [Google Scholar]
  15. Mazidi M. M., Aghjeh M. K. R., Pegoretti A.. Toughened ternary and quaternary polymer alloys of core-shell morphology; correlations among processing, microstructure, micromechanics, and macroscopic mechanical performance in reactive systems. Polymer. 2023;282:126186. doi: 10.1016/j.polymer.2023.126186. [DOI] [Google Scholar]
  16. Wu M., Wu Z., Wang K., Zhang Q., Fu Q.. Simultaneous the thermodynamics favorable compatibility and morphology to achieve excellent comprehensive mechanics in PLA/OBC blend. Polymer. 2014;55(24):6409–6417. doi: 10.1016/j.polymer.2014.10.004. [DOI] [Google Scholar]
  17. Chen Y., Pan M., Li Y., Xu J., Zhong G., Ji X., Yan Z., Li Z.. Core-shell nanoparticles toughened polylactide with excellent transparency and stiffness-toughness balance. Compos. Sci. Technol. 2018;164:168–177. doi: 10.1016/j.compscitech.2018.04.037. [DOI] [Google Scholar]
  18. He L., Song F., Guo Z., Zhao X., Yang N., Wang X., Wang Y.. Toward strong and super-toughened PLA via incorporating a novel fully bio-based copolyester containing cyclic sugar. Compos. Part. B: Eng. 2021;207:108558. doi: 10.1016/j.compositesb.2020.108558. [DOI] [Google Scholar]
  19. Peng T., Lan J., Lu P., Deng C., Zhao Z., Wang Y.. High-Performance Biobased Elastomers with Both High Strength and High Toughness. ACS. Appl. Polym. Mater. 2024;6(7):4204–4214. doi: 10.1021/acsapm.4c00290. [DOI] [Google Scholar]
  20. Chen F., Shangguan Y., Jiang Y., Qiu B., Luo G., Zheng Q.. Toughening with little rigidity loss and mechanism for modified polypropylene by polymer particles with core-shell structure. Polymer. 2015;65:81–92. doi: 10.1016/j.polymer.2015.03.064. [DOI] [Google Scholar]
  21. Shangguan Y., Chen F., Yang J., Jia E., Zheng Q.. A new approach to fabricate polypropylene alloy with excellent low-temperature toughness and balanced toughness-rigidity through unmatched thermal expansion coefficients between components. Polymer. 2017;112:318–324. doi: 10.1016/j.polymer.2017.02.022. [DOI] [Google Scholar]
  22. Wu S.. Phase structure and adhesion in polymer blends: a criterion for rubber toughening. Polymer. 1985;26(12):1855–1863. doi: 10.1016/0032-3861(85)90015-1. [DOI] [Google Scholar]
  23. Zheng W., Li Q., Qi Z.. Percolation model of brittle and ductile transition in PP/EPDM blends. Chinese. Sci. Bull. 1992;37(10):904–907. doi: 10.1360/csb1992-37-10-904. [DOI] [Google Scholar]
  24. Li Q., Zheng W., Qi Z., Wu X., Cai Z.. Damage study on brittle and ductile transition of PP/EPDM blends. Scientia Sinica (Chimica) 1993;23(05):469–474. [Google Scholar]
  25. Huang J., Keskkula H., Paul D.. Rubber toughening of an amorphous polyamide by functionalized SEBS copolymers: morphology and Izod impact behavior. Polymer. 2004;45(12):4203–4215. doi: 10.1016/j.polymer.2004.04.002. [DOI] [Google Scholar]
  26. Oshinski A., Keskkula H., Paul D.. Rubber toughening of polyamides with functionalized block copolymers: 1. Nylon-6. Polymer. 1992;33(2):268–283. doi: 10.1016/0032-3861(92)90984-5. [DOI] [Google Scholar]
  27. Oshinski A., Keskkula H., Paul D.. Rubber toughening of polyamides with functionalized block copolymers: 2. Nylon-6, 6. Polymer. 1992;33(2):284–293. doi: 10.1016/0032-3861(92)90985-6. [DOI] [Google Scholar]
  28. Bucknall C., Paul D.. Notched impact behavior of polymer blends: Part 1: New model for particle size dependence. Polymer. 2009;50(23):5539–5548. doi: 10.1016/j.polymer.2009.09.059. [DOI] [Google Scholar]
  29. Bucknall C., Paul D.. Notched impact behaviour of polymer blends: Part 2: Dependence of critical particle size on rubber particle volume fraction. Polymer. 2013;54(1):320–329. doi: 10.1016/j.polymer.2012.11.019. [DOI] [Google Scholar]
  30. Wu S.. A generalized criterion for rubber toughening: the critical matrix ligament thickness. J. Appl. Polym. Sci. 1988;35(2):549–561. doi: 10.1002/app.1988.070350220. [DOI] [Google Scholar]
  31. Liu Z., Zhang X., Zhu X., Qi Z., Wang F.. Effect of morphology on the brittle ductile transition of polymer blends: 1. A new equation for correlating morphological parameters. Polymer. 1997;38(21):5267–5273. doi: 10.1016/S0032-3861(97)00075-X. [DOI] [Google Scholar]
  32. Zheng W., Li Q., Qi Z.. Percolation model of brittle-ductile transition in PP/EPDM blends. J. Polym. Eng. 1993;12(3):229–238. doi: 10.1515/POLYENG.1993.12.3.229. [DOI] [Google Scholar]
  33. Bartczak Z., Argon A., Cohen R., Weinberg M.. Toughness mechanism in semi-crystalline polymer blends: I. High-density polyethylene toughened with rubbers. Polymer. 1999;40(9):2331–2346. doi: 10.1016/S0032-3861(98)00445-5. [DOI] [Google Scholar]
  34. Gilbert D., Donald A.. Toughening mechanisms in high impact polystyrene. J. Mater. Sci. 1986;21:1819–1823. doi: 10.1007/BF01114745. [DOI] [Google Scholar]
  35. Loyens W., Groeninckx G.. Rubber toughened semicrystalline PET: influence of the matrix properties and test temperature. Polymer. 2003;44(1):123–136. doi: 10.1016/S0032-3861(02)00743-7. [DOI] [Google Scholar]
  36. Thermoplastic compositions. UK GB998439A, 1963.
  37. Epstein, B. N. Tough thermoplastic nylon compositions. U.S. Patent 4,174,358, 1979.
  38. Borggreve R. J. M., Gaymans R. J., Schuijer J.. Impact behaviour of nylon-rubber blends: 5. Influence of the mechanical properties of the elastomer. Polymer. 1989;30(1):71–77. doi: 10.1016/0032-3861(89)90385-6. [DOI] [Google Scholar]
  39. Yang J., Li F., Guan C., Xu X., Zhong L., Gao Y., Han Y., Yan N., Zhao G., Jiang W.. Brittle-ductile transition of impact PP blends: effect of modulus ratio of PP matrix to impact modifier. Polym. Bull. 2023;80(4):4459–4471. doi: 10.1007/s00289-022-04285-0. [DOI] [Google Scholar]
  40. Borggreve R., Gaymans R., Eichenwald H.. Impact behaviour of nylon-rubber blends: 6. Influence of structure on voiding processes; toughening mechanism. Polymer. 1989;30(1):78–83. doi: 10.1016/0032-3861(89)90386-8. [DOI] [Google Scholar]
  41. Liang H., Jiang W., Zhang J., Jiang B.. Toughening mechanism of polymer blends: Influence of voiding ability of dispersed-phase particles. J. Appl. Polym. Sci. 1996;59(3):505–509. doi: 10.1002/(SICI)1097-4628(19960118)59:3<505::AID-APP16>3.0.CO;2-S. [DOI] [Google Scholar]
  42. Van der Wal A., Mulder J. J., Oderkerk J., Gaymans R. J.. Polypropylene-rubber blends: 1. The effect of the matrix properties on the impact behaviour. Polymer. 1998;39(26):6781–6787. doi: 10.1016/S0032-3861(98)00170-0. [DOI] [Google Scholar]
  43. Li F., Gao Y., Zhang C., Jin J., Ji X., Zhang Y., Zhang X., Jiang W.. Design of high impact thermal plastic polymer composites with balanced toughness and rigidity: Effect of matrix polymer molecular weight. Polymer. 2020;208:122957. doi: 10.1016/j.polymer.2020.122957. [DOI] [Google Scholar]
  44. Li F., Gao Y., Yan N., Zhang C., Zhang X., Jiang W.. Effect of polypropylene molecular weight distribution on the balance between the toughness and rigidity of the impact polypropylene composites. J. Appl. Polym. Sci. 2022;139(12):51834. doi: 10.1002/app.51834. [DOI] [Google Scholar]
  45. Borggreve R., Gaymans R.. Impact behaviour of nylon-rubber blends: 4. Effect of the coupling agent, maleic anhydride. Polymer. 1989;30(1):63–70. doi: 10.1016/0032-3861(89)90384-4. [DOI] [Google Scholar]
  46. Borggreve R., Gaymans R., Schuijer J., Housz J. I.. Brittle-tough transition in nylon-rubber blends: effect of rubber concentration and particle size. Polymer. 1987;28(9):1489–1496. doi: 10.1016/0032-3861(87)90348-X. [DOI] [Google Scholar]
  47. Jiang W., Liu C., Wang Z., An L., Liang H., Jiang B., Wang X., Zhang H.. Brittle-tough transition in PP/EPDM blends: effects of interparticle distance and temperature. Polymer. 1998;39(14):3285–3288. doi: 10.1016/S0032-3861(97)10083-0. [DOI] [Google Scholar]
  48. Jiang W., Tjong S., Li R.. Brittle-tough transition in PP/EPDM blends: effects of interparticle distance and tensile deformation speed. Polymer. 2000;41(9):3479–3482. doi: 10.1016/S0032-3861(99)00747-8. [DOI] [Google Scholar]
  49. Huang L., Pei Q., Yuan Q., Li H., Cheng F., Ma J., Jiang S., An L., Jiang W.. Brittle-ductile transition in PP/EPDM blends: effect of notch radius. Polymer. 2003;44(10):3125–3131. doi: 10.1016/S0032-3861(03)00205-2. [DOI] [Google Scholar]
  50. Margolina A., Wu S.. Percolation model for brittle-tough transition in nylon/rubber blends. Polymer. 1988;29(12):2170–2173. doi: 10.1016/0032-3861(88)90108-5. [DOI] [Google Scholar]
  51. Margolina A.. Toughening mechanism for nylon/rubber blends: The effect of temperature. Polymer Communications. 1990;31(3):95–96. [Google Scholar]
  52. Van der Sanden M. C. M., Meijer H. E. H., Tervoort T. A.. Deformation and toughness of polymeric systems: 2. Influence of entanglement density. Polymer. 1993;34(14):2961–2970. doi: 10.1016/0032-3861(93)90621-G. [DOI] [Google Scholar]
  53. Eyring H.. Viscosity, Plasticity, and Diffusion as Examples of Absolute Reaction Rates. J. Chem. Phys. 1936;4(4):283–291. doi: 10.1063/1.1749836. [DOI] [Google Scholar]
  54. Van der Sanden M. C. M., de Kok J. M. M., Meijer H. E. H.. Deformation and toughness of polymeric systems: 7. Influence of dispersed rubbery phase. Polymer. 1994;35(14):2995–3004. doi: 10.1016/0032-3861(94)90412-X. [DOI] [Google Scholar]
  55. Corté L., Leibler L.. A Model for Toughening of Semicrystalline Polymers. Macromolecules. 2007;40(15):5606–5611. doi: 10.1021/ma0706935. [DOI] [Google Scholar]
  56. Muratoglu O. K., Argon A. S., Cohen R. E., Weinberg M.. Toughening mechanism of rubber-modified polyamides. Polymer. 1995;36(5):921–930. doi: 10.1016/0032-3861(95)93590-I. [DOI] [Google Scholar]
  57. Bartczak Z., Argon A., Cohen R., Kowalewski T.. The morphology and orientation of polyethylene in films of sub-micron thickness crystallized in contact with calcite and rubber substrates. Polymer. 1999;40(9):2367–2380. doi: 10.1016/S0032-3861(98)00443-1. [DOI] [Google Scholar]
  58. Jiang W., Liang H., Jiang B.. Interparticle distance-temperature-strain rate equivalence for the brittle-tough transition in polymer blends. Polymer. 1998;39(18):4437–4442. doi: 10.1016/S0032-3861(97)00627-7. [DOI] [Google Scholar]
  59. Jiang W., Yu D., Jiang B.. Brittle-ductile transition of particle toughened polymers: influence of the matrix properties. Polymer. 2004;45(19):6427–6430. doi: 10.1016/j.polymer.2004.07.023. [DOI] [Google Scholar]
  60. Jiang W., Hu Y., Yin J.. Critical behavior of brittle-ductile transition of polymers. J. Polym. Sci. Polym. Phys. 2008;46(7):766–769. doi: 10.1002/polb.21411. [DOI] [Google Scholar]
  61. Gaymans R. J., Borggreve R. J. M., Spoelstra A. B.. Ductile transition in nylon-rubber blends: Influence of water. J. Appl. Polym. Sci. 1989;37(2):479–486. doi: 10.1002/app.1989.070370214. [DOI] [Google Scholar]
  62. Williams, J. G. Stress analysis of polymers; Longman, 1973. [Google Scholar]
  63. Liu S. H., Nauman E. B.. On the micromechanics of composites containing spherical inclusions. J. Mater. Sci. 1990;25(4):2071–2076. doi: 10.1007/BF01045766. [DOI] [Google Scholar]
  64. Jiang W., An L., Jiang B.. Brittle-tough transition in elastomer toughening thermoplastics: effects of the elastomer stiffness. Polymer. 2001;42(10):4777–4780. doi: 10.1016/S0032-3861(00)00634-0. [DOI] [Google Scholar]
  65. Goodier J. N.. Concentration of Stress Around Spherical and Cylindrical Inclusions and Flaws. Journal of Applied Mechanics. 1933;1(2):39–44. doi: 10.1115/1.4012173. [DOI] [Google Scholar]
  66. Flory P. J.. Tensile Strength in Relation to Molecular Weight of High Polymers. Rubber Chem. Technol. 1946;19(3):599–601. doi: 10.5254/1.3543215. [DOI] [Google Scholar]
  67. Fasihi M., Mansouri H.. Effect of rubber interparticle distance distribution on toughening behavior of thermoplastic polyolefin elastomer toughened polypropylene. J. Appl. Polym. Sci. 2016 doi: 10.1002/app.44068. [DOI] [Google Scholar]
  68. Corté L., Rebizant V., Hochstetter G., Tournilhac F., Leibler L.. Toughening with Little Stiffness Loss: Polyamide Filled with ABC Triblock Copolymers. Macromolecules. 2006;39(26):9365–9374. doi: 10.1021/ma061090g. [DOI] [Google Scholar]
  69. Zuiderduin W. C. J., Westzaan C., Huétink J., Gaymans R. J.. Toughening of polypropylene with calcium carbonate particles. Polymer. 2003;44(1):261–275. doi: 10.1016/S0032-3861(02)00769-3. [DOI] [Google Scholar]
  70. Zhang J., Hong J., Wang H., Li Y.. Acrylonitrile-butadiene-styrene (ABS) salami structure inspired PLLA composites with excellent stiffness-toughness balance. Compos. Commun. 2023;42:101680. doi: 10.1016/j.coco.2023.101680. [DOI] [Google Scholar]
  71. Li F., Gao Y., Jiang W.. Design of high impact thermal plastic polymer composites with balanced toughness and rigidity: Toughening with one phase modifier. Polymer. 2019;170:101–106. doi: 10.1016/j.polymer.2019.03.004. [DOI] [Google Scholar]
  72. Takayanagi M., Uemura S., Minami S.. Application of equivalent model method to dynamic rheo-optical properties of crystalline polymer. J. Polym. Sci. Pt. C-Polym. Symp. 1964;5(1):113–122. doi: 10.1002/polc.5070050111. [DOI] [Google Scholar]
  73. Li Z., Muiruri J. K., Thitsartarn W., Zhang X., Tan B. H., He C.. Biodegradable silica rubber core-shell nanoparticles and their stereocomplex for efficient PLA toughening. Compos. Sci. Technol. 2018;159:11–17. doi: 10.1016/j.compscitech.2018.02.026. [DOI] [Google Scholar]
  74. Xu C., Ma J., Li G., Wang N., Zhang Q., Grami M. E., Qu X.. Enhanced toughness for polyamide 6 with a core-shell structured polyacrylic modifier. J. Polym. Res. 2017;24(9):147. doi: 10.1007/s10965-017-1308-2. [DOI] [Google Scholar]
  75. Liu H., Zhang T., Cai Y., Deng S., Bai D., Bai H., Zhang Q., Fu Q.. Towards polylactide/core-shell rubber blends with balanced stiffness and toughness via the formation of rubber particle network with the aid of stereocomplex crystallites. Polymer. 2018;159:23–31. doi: 10.1016/j.polymer.2018.11.013. [DOI] [Google Scholar]
  76. He X., Shi J., Wu L., Jiang P., Liu B.. Study on synergistic toughening of polypropylene with high-density polyethylene and elastomer-olefin block copolymers under ultrasonic application. Compos. Sci. Technol. 2018;161:115–123. doi: 10.1016/j.compscitech.2018.03.044. [DOI] [Google Scholar]
  77. Qi L., Wu L., He R., Cheng H., Liu B., He X.. Synergistic toughening of polypropylene with ultra-high molecular weight polyethylene and elastomer-olefin block copolymers. RSC Adv. 2019;9(41):23994–24002. doi: 10.1039/C9RA01073D. [DOI] [PMC free article] [PubMed] [Google Scholar]
  78. Wu Y., Zhang H., Shentu B., Weng Z.. In Situ Formation of the Core-Shell Particles and Their Function in Toughening PA6/SEBS-g-MA/PP Blends. Ind. Eng. Chem. Res. 2017;56(41):11657–11663. doi: 10.1021/acs.iecr.7b02202. [DOI] [Google Scholar]
  79. Chen Y., Ye L.. Structure and Properties of PP/POE/HDPE Blends. J. Appl. Polym. Sci. 2011;121(2):1013–1022. doi: 10.1002/app.33706. [DOI] [Google Scholar]
  80. Louizi M., Massardier V., Cassagnau P.. Contribution of High-shear Processing to the Compatibilization of (PP/EPR)/PE Ternary Blends. Macromol. Mater. Eng. 2014;299(6):674–688. doi: 10.1002/mame.201300268. [DOI] [Google Scholar]
  81. Wang J., Niu H., Dong J., Du J., Han C. C.. Morphology and mechanical properties of polypropylene/poly (propylene-1-octene) in-reactor alloys prepared by Metallocene/Ziegler-Natta hybrid catalyst. Polymer. 2012;53(7):1507–1516. doi: 10.1016/j.polymer.2012.02.017. [DOI] [Google Scholar]
  82. Zhang B., Fu Z., Fan Z., Phiriyawirut P., Charoenchaidet S.. Preparation and characterization of high MFR polypropylene and polypropylene/poly­(ethylene-co-propylene) in-reactor alloys. J. Appl. Polym. Sci. 2016;133(8):42984. doi: 10.1002/app.42984. [DOI] [Google Scholar]
  83. Galli P., Haylock J. C.. Continuing initiator system developments provide a new horizon for polyolefin quality and properties. Prog. Polym. Sci. 1991;16(2):443–462. doi: 10.1016/0079-6700(91)90025-G. [DOI] [Google Scholar]
  84. Simonazzi T., Cecchin G., Mazzullo S.. An outlook on progress in polypropylene-based polymer technology. Prog. Polym. Sci. 1991;16(2):303–329. doi: 10.1016/0079-6700(91)90021-C. [DOI] [Google Scholar]
  85. Zhang C., Shangguan Y., Chen R., Wu Y., Chen F., Zheng Q., Hu G.. Morphology, microstructure and compatibility of impact polypropylene copolymer. Polymer. 2010;51(21):4969–4977. doi: 10.1016/j.polymer.2010.08.021. [DOI] [Google Scholar]
  86. Li Y., Xu J., Dong Q., Fu Z., Fan Z.. Morphology of polypropylene/poly­(ethylene-co-propylene) in-reactor alloys prepared by multi-stage sequential polymerization and two-stage polymerization. Polymer. 2009;50(21):5134–5141. doi: 10.1016/j.polymer.2009.09.008. [DOI] [Google Scholar]
  87. Fan Z., Zhang Y., Xu J., Wang H., Feng L.. Structure and properties of polypropylene/poly­(ethylene-co-propylene) in-situ blends synthesized by spherical Ziegler-Natta catalyst. Polymer. 2001;42(13):5559–5566. doi: 10.1016/S0032-3861(01)00062-3. [DOI] [Google Scholar]
  88. Fu Z., Fan Z., Zhang Y., Feng L.. Structure and morphology of polypropylene/poly­(ethylene-co-propylene) in situ blends synthesized by spherical Ziegler-Natta catalyst. Eur. Polym. J. 2003;39(4):795–804. doi: 10.1016/S0014-3057(02)00287-2. [DOI] [Google Scholar]
  89. Luo F., Xu C., Wang K., Deng H., Chen F., Fu Q.. Exploring temperature dependence of the toughening behavior of β-nucleated impact polypropylene copolymer. Polymer. 2012;53(8):1783–1790. doi: 10.1016/j.polymer.2012.02.024. [DOI] [Google Scholar]
  90. Chen F., Qiu B., Ye Y., Lv Y., Shangguan Y., Song Y., Zheng Q.. Reconstruction of core-shell dispersed particles in impact polypropylene copolymer during extrusion. Chinese. J. Polym. Sci. 2015;33(4):633–645. doi: 10.1007/s10118-015-1616-0. [DOI] [Google Scholar]
  91. Song S., Feng J., Wu P., Yang Y.. Shear-Enhanced Crystallization in Impact-Resistant Polypropylene Copolymer: Influence of Compositional Heterogeneity and Phase Structure. Macromolecules. 2009;42(18):7067–7078. doi: 10.1021/ma9004764. [DOI] [Google Scholar]
  92. Urdampilleta I., González A., Iruin J. J., de la Cal J. C., Asua J. M.. Morphology of High Impact Polypropylene Particles. Macromolecules. 2005;38(7):2795–2801. doi: 10.1021/ma047413v. [DOI] [Google Scholar]
  93. Tong C., Lan Y., Chen Y., Chen Y., Yang D., Yang X.. The Functions of Crystallizable Ethylene-Propylene Copolymers in the Formation of Multiple Phase Morphology of High Impact Polypropylene. J. Appl. Polym. Sci. 2012;123(3):1302–1309. doi: 10.1002/app.34609. [DOI] [Google Scholar]
  94. Chen Y., Chen Y., Chen W., Yang D.. Multilayered core-shell structure of the dispersed phase in high-impact polypropylene. J. Appl. Polym. Sci. 2008;108(4):2379–2385. doi: 10.1002/app.25410. [DOI] [Google Scholar]
  95. Tang F., Bao P., Su Z.. Analysis of Nanodomain Composition in High-Impact Polypropylene by Atomic Force Microscopy-Infrared. Anal. Chem. 2016;88(9):4926–4930. doi: 10.1021/acs.analchem.6b00798. [DOI] [PubMed] [Google Scholar]
  96. Li C., Wang Z., Liu W., Ji X., Su Z.. Copolymer Distribution in Core-Shell Rubber Particles in High-Impact Polypropylene Investigated by Atomic Force Microscopy-Infrared. Macromolecules. 2020;53(7):2686–2693. doi: 10.1021/acs.macromol.0c00328. [DOI] [Google Scholar]
  97. Shen C., Zhou Y., Dou R., Wang W., Yin B., Yang M.. Effect of the core-forming polymer on phase morphology and mechanical properties of PA6/EPDM-g-MA/HDPE ternary blends. Polymer. 2015;56:395–405. doi: 10.1016/j.polymer.2014.11.027. [DOI] [Google Scholar]
  98. Yin B., Li L., Zhou Y., Gong L., Yang M., Xie B.. Largely improved impact toughness of PA6/EPDM-g-MA/HDPE ternary blends: The role of core-shell particles formed in melt processing on preventing micro-crack propagation. Polymer. 2013;54(7):1938–1947. doi: 10.1016/j.polymer.2013.02.001. [DOI] [Google Scholar]
  99. Bao W., Gao Y., Zhang J., Jin J., Liu B., Zhang M., Ji X., Jiang W.. In situ formation of PE-EPR core-shell rubber particles in polypropylene matrix by melt blending: Effect of PE chain structure and viscosity. J. Appl. Polym. Sci. 2024;141(46):e56245. doi: 10.1002/app.56245. [DOI] [Google Scholar]
  100. Ji X., Jing J., Jiang W., Jiang B.. Tensile modulus of polymer nanocomposites. Polym. Eng. Sci. 2002;42(5):983–993. doi: 10.1002/pen.11007. [DOI] [Google Scholar]
  101. Li F., Gao Y., Zhang Y., Jiang W.. Design of high impact thermal plastic polymer composites with balanced toughness and rigidity: Toughening with core-shell rubber modifier. Polymer. 2020;191:122237. doi: 10.1016/j.polymer.2020.122237. [DOI] [Google Scholar]
  102. Jia E., Zhao S., Shangguan Y., Zheng Q.. Toughening mechanism of polypropylene bends with polymer particles in core-shell structure: Equivalent rubber content effect related to core-shell interfacial strength. Polymer. 2019;178:121602. doi: 10.1016/j.polymer.2019.121602. [DOI] [Google Scholar]
  103. Tang F., Bao P., Roy A., Wang Y., Su Z.. In-situ spectroscopic and thermal analyses of phase domains in high-impact polypropylene. Polymer. 2018;142:155–163. doi: 10.1016/j.polymer.2018.03.037. [DOI] [Google Scholar]
  104. Dizaji S. M., Katbab A. A., Hajibabazadeh S.. Role of interfacial compatibilizer and functionality of rubber phase on micromorphology development and mechanical properties of PP/EPDM/nanosilica ternary nanocomposite. Polym. Bull. 2023;80(2):1353–1368. doi: 10.1007/s00289-022-04112-6. [DOI] [Google Scholar]
  105. Uotila R., Hippi U., Paavola S., Seppälä J.. Compatibilization of PP/elastomer/microsilica composites with functionalized polyolefins: Effect on microstructure and mechanical properties. Polymer. 2005;46(19):7923–7930. doi: 10.1016/j.polymer.2005.06.099. [DOI] [Google Scholar]
  106. Wang X., Gao Y., Jin J., Jiang W.. A Strategy to Develop Homo-polypropylene Composites with High Impact and High Rigidity. Macromolecules. 2024;57(9):4576–4583. doi: 10.1021/acs.macromol.3c02530. [DOI] [Google Scholar]
  107. Zhang L., Li C., Huang R.. Toughness mechanism in polypropylene composites: Polypropylene toughened with elastomer and calcium carbonate. J. Polym. Sci. Polym. Phys. 2004;42(9):1656–1662. doi: 10.1002/polb.20035. [DOI] [Google Scholar]
  108. Fu Q., Wang G., Shen J.. Polyethylene toughened by CaCO3 particle: Brittle-ductile transition of CaCO3-toughened HDPE. J. Appl. Polym. Sci. 1993;49(4):673–677. doi: 10.1002/app.1993.070490412. [DOI] [Google Scholar]
  109. Fu Q., Wang G.. Effect of morphology on brittle-ductile transition of HPDE/CaCO3 blends. J. Appl. Polym. Sci. 1993;49(11):1985–1988. doi: 10.1002/app.1993.070491115. [DOI] [Google Scholar]

Articles from Polymer Science & Technology are provided here courtesy of American Chemical Society

RESOURCES