Abstract
Coal facies differentiation is a primary control on the development of pore-fracture systems in coal reservoirs. Using samples from diverse sedimentary environments of the Jurassic Yan’an Formation in the Ningdong Coalfield, this study integrates coal petrological analysis, multiscale pore characterization, and rock mechanical testing to examine the characteristics of pore-fracture development as constrained by coal facies. The results indicate that the study area developed four types of peat swamps: wetland herbaceous peat swamp (WLHPS), dry forest peat swamp (DFPS), moist forest peat swamp (MFPS), and shallow-water covered forest peat swamp (SWCFPS), with DFPS being dominant. Among primary pores, cellular pores are most developed in WLHPS (mean 12.68 μm), whereas pores in forest peat swamps (including DFPS, MFPS, and SWCFPS) are smaller. For mineral-related pores, intercrystalline pores dominate in WLHPS (mean 12.36 μm), while dissolution pores are well-developed in DFPS. Pore structure analysis reveals that forest peat swamps exhibit higher pore volumes (0.12–0.16 cm3/g) than WLHPS (0.06 cm3/g), with SWCFPS containing the highest proportion of macropores. Average specific surface area is also greater in forest peat swamps than in WLHPS. Analysis of the fracture system indicates that WLHPS has lower porosity but the smallest proportion of isolated pores. Cleat fractures are well-developed in DFPS, although partial mineral filling reduces pore connectivity. MFPS exhibits the best pore connectivity (CT-connected porosity: 16.39%). Mechanical response analysis shows that elastic modulus decreases with increasing water coverage depth, while rigid minerals such as calcite and pyrite significantly enhance deformation resistance. Coal facies are the core controlling factor of the pore-fracture system: SWCFPS, characterized by high pore volume, preferential formation of connected macropores, and moderate gelification, represents the optimal reservoir for coalbed methane (CBM) development; the high-connectivity cleat system in DFPS requires mitigation of mineral filling risks; and the low pore volume and isolated pores in WLHPS constrain its seepage capacity.


1. Introduction
The Ordos Basin, a critical energy hub in China, hosts abundant coal and coalbed methane (CBM) resources. Its multilayered coal seams hold substantial potential for developing large-scale CBM fields. − Situated on the western margin of the basin, the Ningdong Coalfield not only boasts high-quality coal resources but also, due to its unique geological setting, serves as a key area for exploring efficient CBM development. − Against the backdrop of advancing global low-carbon development strategies and national energy structure adjustments, systematically revealing the developmental patterns of pore-fracture systems in CBM reservoirs is crucial for improving CBM exploration efficiency and promoting the transition to cleaner energy. ,
The pore-fracture system in coal reservoirs acts as the primary pathway for CBM adsorption, storage, and seepage. Its geometric morphology, connectivity, and spatial distribution fundamentally govern the reservoir’s gas content, permeability, and stimulation potential. − Studies have shown that coal facies, a comprehensive geological entity shaped by the composition of original coal-forming materials and the degree of mineral filling, is a key endogenous factor influencing the primary characteristics of the pore-fracture system. , Maceral differentiation affects pore genetic types (e.g., desiccation cracks in vitrinite, cellular pores in fusinite), with inertinite content significantly impacting matrix mechanical strength and fracture propagation patterns. Conversely, the filling of secondary minerals (e.g., pyrite, calcite) can locally block or alter the pore network. , Recent advancements in multiscale pore characterization techniques have gradually established semiquantitative relationships between macerals and pore types. However, existing research often focuses on reservoirs within single sedimentary environments, lacking a systematic understanding of the coevolution mechanisms of pore-fracture structures dominated by multiple coal facies types within the same geological unit. − In particular, the precise mechanisms by which coal facies heterogeneity influences reservoir engineering responses in three-dimensional space remain unclear, limiting the accuracy of predicting reservoir “sweet spots”.
As a pivotal geological unit on the western margin of the Ordos Basin, the Ningdong Coalfield exhibits significant spatial differentiation of coal facies. This is controlled by frequent oscillations of the fluvial-deltaic system during the deposition of the Jurassic Yan’an Formation, resulting in stacked coal seams formed in various sedimentary environments within the coalfield. , Although the main structural framework is relatively broad and gently dipping, the far-field effects of the western marginal thrust belt have locally induced dense joints and interlayer detachment, exacerbating coal structure fragmentation and forming a composite pore-fracture network comprising both natural fractures and coal rock fractures. , Against this background, precisely characterizing the pore-fracture structures and mechanical behaviors of reservoirs under different sedimentary environments is crucial for guiding the design of high-risk deep well fracturing and production forecasting.
This study focuses on the Ningdong Coalfield. Representative samples were selected, and methods including coal petrological analysis, detailed reservoir characterization, and rock mechanical experiments were comprehensively applied. The aims are to (1) clarify the compositional differences of coal seams from different coal facies; (2) systematically analyze variations in parameters such as pore morphology and structure controlled by different coal facies; (3) establish a coal facies-constrained pore-fracture network model through three-dimensional digital core reconstruction; and (4) elucidate the controlling effect of coal facies differences on fracture propagation and reservoir mechanical responses, combined with mechanical parameter analysis.
2. Samples and Experiments
2.1. Geological Setting
The Ningdong Coalfield is located in the transitional zone on the western margin of the Ordos Basin, at the tectonic boundary between the stable North China Craton and the active Alxa Block. This tectonic position has shaped a unique structural framework characterized by “east–west zonation and north–south banding” (Figure ). The Tianhuan Depression forms the boundary for the east–west zonation, and the eastern part belongs to the stable intracontinental basin unit of the Ordos Basin, with weak structural deformation and formation dips <5°; the western part constitutes the Western Margin Fold-Thrust Belt, featuring an imbricate thrust fault system. Coal seams in the east exhibit good continuity, while in the west, thrust-nappe modification has led to coal seams predominantly occurring as fault slices. In the north, controlled by the Helanshan Thrust-Nappe structural system, the maximum principal stress direction is NW-SE, with near north–south trending faults developed. In the south, dominated by the eastern piedmont thrust-nappe system of the Liupan Mountains, the principal stress shifts to NE-SW.
1.
(a) Tectonic units of the Ordos Basin and location of the Ningdong Coalfield (modified from ref ). (b) The Ningdong coalfield block and sampling point (modified from ref ). (c) Stratigraphic column of Jurassic Yan’an Formation in the Ningdong Coalfield (modified from ref ).
The sedimentary evolution of the coal-bearing Middle Jurassic Yan’an Formation in the Ningdong Coalfield underwent a complete cycle, resulting in the formation of a multifacies composite sedimentary system. This system directly controlled the vertical variation and differentiation of coal facies types. The Yan’an Formation is subdivided into five members from bottom to top, primarily consisting of two major sedimentary systems (fluvial and deltaic). The fluvial-deltaic sedimentary system developed in Member I and parts of Member V, while the deltaic sedimentary system is widely distributed in Members II, III, IV, and V. Within the fluvial facies, pebbly coarse sandstones and medium sandstones dominate; frequent channel migration caused significant variations in coal seam thickness. Within the deltaic facies, subaqueous distributary channels and interdistributary bay microfacies are predominant, with well-developed sandbodies commonly exhibiting small-scale cross-bedding and plant root fossils. The upper lithology is characterized by interbedded fine sandstones and carbonaceous mudstones, reflecting the progradation of the delta front. Overall, the Yan’an Formation is dominated by fine-grained clastic sediments with intense coal accumulation, hosting over 18 coal seams that primarily occur at the tops of individual sedimentary cycles.
2.2. Samples and Experimental Methods
In this study, 10 coal samples were systematically collected from the Lingwu, Jijiajing, Majiatan, and Yuanyanghu mining areas. After surface cleaning and natural air-drying, the samples were sealed in airtight bags and immediately transported to the laboratory for subsequent analysis. The Ro of the coal samples ranges from 0.53% to 1.00%, with an average of 0.67%, indicating that they are low-rank bituminous coals. The maceral composition is dominated by vitrinite (average 49.9%) and inertinite (average 47.1%), with the lowest content of liptinite. Proximate analysis results show that the samples are characterized by low moisture (average 1.63%), low ash yield (average 7.67%), medium volatile matter (average 32.47%), and high fixed carbon (average 58.23%).
2.2.1. Scanning Electron Microscopy (SEM)
A Zeiss Sigma 500 field-emission scanning electron microscope was used in accordance with the industry standard SY/T 5162-2021 “Analytical Method of Rocks by Scanning Electron Microscopy”. Observations focused on the micromorphology of the coal surface, specifically targeting pore structures, microfractures, and mineral occurrence characteristics. ImageJ software was applied for semiquantitative analysis of the acquired images to statistically evaluate pore parameters.
2.2.2. Low-Field Nuclear Magnetic Resonance (NMR)
Experiments were conducted using a MicroMR12-025 V NMR analyzer, adhering to the industry standard SY/T 6490-2014 “Specification for Laboratory Measurement of Rock NMR Parameters”. Coal plugs, approximately 2.5 cm in diameter and 2–5 cm in length, were drilled parallel to the face cleat orientation and prepared as standard cylindrical specimens. This technique enabled nondestructive acquisition of pore structure information within the coal samples, facilitating comprehensive identification of pores across different aperture scales.
2.2.3. Micro-Computed Tomography (μCT)
Three-dimensional structural visualization of coal samples was performed using a ZEISS Xradia 520 Versa industrial CT system. The system offers a spatial resolution of ∼50 μm, allowing precise characterization of macropores and microfracture networks within the coal. Standard cylindrical specimens were prepared and securely fixed onto the scanner stage. After setting scan parameters, the samples underwent 360° rotation for layer-by-layer scanning. The acquired data were processed using Avizo software for three-dimensional reconstruction and visualization analysis.
2.2.4. Rock Mechanical Parameter Testing
Determination of rock mechanical parameters followed the Chinese National Standard GB/T 23561.8-2009 “Methods for Determining the Physical and Mechanical Properties of Coal and RockPart 8: Methods for Determining the Deformation Parameters of Coal and Rock”. Tests were performed on a YDAW-300 reservoir geomechanical testing system using conventional triaxial compression (σ1 > σ2 = σ3). Under constant confining pressure (σ2 = σ3), lateral and longitudinal deformations under axial loading were measured to calculate the coal’s triaxial compressive strength, Poisson’s ratio, and elastic modulus. These test conditions simulated the actual in situ stress state (σ1 > σ2 = σ3).
2.2.5. X-ray Diffraction (XRD)
The mineral composition within the coal was characterized using a Rigaku Ultima IV X-ray diffractometer, in accordance with the industry standard SY/T 5163-2018 “Analysis Method for Clay Minerals and Common Non-clay Minerals in Sedimentary Rocks by X-ray Diffraction”. Coal samples were first ground into powder; mineral diffraction patterns were obtained via X-ray diffraction, and data processing coupled with specialized software enabled quantitative whole-rock analysis to determine the types and relative abundances of different minerals present in the coal.
2.2.6. Maceral Analysis
The maceral composition within the coal was determined using a point-counting method on polished coal sections, in accordance with the Chinese National Standard GB/T 8899-2013 “Method for Determining Maceral Group Composition and Minerals in Coal”. Quantitative identification of macerals and minerals was carried out through statistical point-counting under a reflected-light microscope (500 points), enabling the calculation of volume percentages for individual maceral groups and mineral constituents.
2.2.7. Coal Facies Parameter Calculation
Coal facies parameters are widely used in studies of coal-forming environments, vegetation types, and hydrodynamic conditions. Key parameters include the Gelification Index (GI), Tissue Preservation Index (TPI), Groundwater Influence Index (GWI), and Vegetation Index (VI) (Diessel, 1992; Jiu et al., 2021). Based on maceral subcomponent data, the coal facies parameters were calculated using the following formulas:
| 1 |
| 2 |
| 3 |
| 4 |
3. Results and Discussion
3.1. Coal Facies Types
Coal facies reflect the comprehensive characteristics of source materials and depositional environments during coal formation. Quantitative maceral analysis of coal samples from the Yan’an Formation in the Ningdong Coalfield (Table ) shows that inertinite is the dominant maceral (20.9%–80.6%, average 48.69%, followed by vitrinite (18.3%–83.4%, average 44.94%, with the two groups having relatively similar abundances. Liptinite is the least abundant (0.6%–8.8%, average 2.65%, while mineral content varies considerably (0.4%–28.6%, average 3.37%, with clay minerals as the primary component.
1. Maceral Components of the Jurassic Yan’an Formation Samples.
| Maceral components (%) | ND-3 | ND-4 | ND-5 | ND-6 | ND-8 | ND-9 | ND-10 | ND-12 | ND-13 | ND-14 | Mean |
|---|---|---|---|---|---|---|---|---|---|---|---|
| Total Mineral Matter | 28.6 | 2.6 | 1.5 | 0.5 | 0.4 | 1.5 | 0.8 | 0.4 | 0.4 | 0.5 | 3.72 |
| Clay Minerals | 27.5 | 1.7 | 1.3 | 0.4 | 0.3 | 1.2 | 0.3 | 0.2 | 0.3 | 0.3 | 3.35 |
| Pyrite | 1.1 | 0.9 | 0.2 | 0.1 | 0.1 | 0.3 | 0.4 | 0.2 | 0.1 | 0.2 | 0.36 |
| Calcite | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 | 0.1 | 0.0 | 0.0 | 0.0 | 0.01 |
| Total Vitrinite | 23.8 | 18.7 | 60.6 | 18.3 | 76.5 | 59.2 | 24.4 | 83.4 | 50.2 | 34.3 | 44.94 |
| Telinite | 0.0 | 8.2 | 0.0 | 0.0 | 0.0 | 0.0 | 4.6 | 0.0 | 0.0 | 0.0 | 1.28 |
| Desmocollinite | 16.6 | 6.6 | 35.5 | 5.7 | 66.7 | 46.7 | 8.5 | 34.9 | 21.0 | 20.7 | 26.29 |
| Telocollinite | 1.3 | 3.2 | 24.8 | 12.6 | 9.8 | 12.5 | 11.3 | 48.5 | 29.2 | 13.6 | 16.68 |
| Corpocollinite | 0.2 | 0.1 | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 | 0.03 |
| Vitrodetrinite | 5.7 | 0.6 | 0.3 | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 | 0.66 |
| Total Inertinite | 40.4 | 77.6 | 36.5 | 80.6 | 20.9 | 30.5 | 72.2 | 15.5 | 48.9 | 63.8 | 48.69 |
| Fusinite | 7.7 | 8.5 | 7.3 | 8.5 | 5.1 | 5.6 | 7.2 | 4.1 | 6.7 | 3.5 | 6.42 |
| Semifusinite | 27.1 | 61.8 | 20.1 | 69.2 | 10.9 | 23.4 | 61.1 | 7.3 | 36.8 | 56.2 | 37.39 |
| Macrinite | 1.5 | 4.7 | 6.2 | 1.2 | 2.6 | 2.0 | 2.5 | 2.7 | 3.1 | 1.6 | 2.81 |
| Funginite | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 | 0.1 | 0.0 | 0.0 | 0.0 | 0.01 |
| Inertodetrinite | 4.1 | 2.6 | 2.9 | 1.7 | 2.3 | 1.5 | 1.3 | 1.4 | 2.3 | 2.5 | 2.26 |
| Total Liptinite | 7.2 | 1.1 | 1.4 | 0.6 | 2.2 | 8.8 | 2.6 | 0.7 | 0.5 | 1.4 | 2.65 |
| Sporinite | 5.6 | 0.7 | 0.8 | 0.4 | 1.6 | 6.5 | 1.2 | 0.6 | 0.3 | 0.9 | 1.86 |
| Resinite | 0.2 | 0.0 | 0.1 | 0.0 | 0.1 | 0.1 | 0.1 | 0.0 | 0.1 | 0.1 | 0.08 |
| Cutinite | 0.1 | 0.1 | 0.0 | 0.0 | 0.0 | 1.0 | 1.0 | 0.0 | 0.0 | 0.0 | 0.22 |
| Suberinite | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 | 0.2 | 0.02 |
| Liptodetrinite | 1.3 | 0.3 | 0.5 | 0.2 | 0.5 | 1.2 | 0.3 | 0.1 | 0.1 | 0.2 | 0.47 |
| TPI | 1.29 | 5.63 | 1.16 | 10.50 | 0.36 | 0.83 | 6.85 | 1.54 | 2.75 | 2.96 | 1.86 |
| GI | 0.65 | 0.32 | 2.20 | 0.25 | 4.32 | 2.01 | 0.39 | 6.73 | 1.16 | 0.58 | 3.39 |
| VI | 1.09 | 7.50 | 1.31 | 11.29 | 0.36 | 0.73 | 6.85 | 1.62 | 3.07 | 3.03 | 3.69 |
| GWI | 1.55 | 0.10 | 0.02 | 0.02 | 0.00 | 0.02 | 0.01 | 0.00 | 0.01 | 0.01 | 0.17 |
Among inertinite subgroups, semifusinite is overwhelmingly dominant (average 37.39%), significantly higher than other inertinite components (Figure ). Its enrichment indicates intense fusinitization of plant precursors, which reflects periodic exposure of the peat surface to oxidizing conditions during coal formation. Vitrinite is mainly composed of desmocollinite (average 26.29%) and telocollinite (average 16.68%). Their predominance signifies strong biochemical gelification under stable, deeply submerged, and highly reducing swamp conditionsan environment favorable for the preservation and transformation of organic matter. Sporinite is the main component of liptinite (average 1.86%).
2.
Maceral Subcomponents of Typical Jurassic Yan’an Formation Samples. (a) N-3-3: Fusinite (F) fragments with faint cellular structure in a desmocollinite (DC) matrix; blocky/strip-shaped semifusinite (Sf); dispersed inertodetrinite (ID). (b) N-3-4: Sf, macrinite (Ma), and ID dispersed in DC; clay minerals (Cl) and pyrite (Py) microcrystals are visible. (c) N-4-4: Sf, Ma, and ID within DC; Py microcrystals are visible. (d) N-10-3: Telinite (T) intergrown with DC, containing ID; Sf and Cl are visible. (e) N-3-1: Microsporinite (MiS) arranged subparallel to bedding; resinite (Re) ellipsoids showing bright yellow fluorescence; dispersed liptodetrinite (LD). (f) N-9-1: Cutinite (Cu) as curved bands subparallel to bedding, locally fractured; layered MiS; Re ellipsoids with bright yellow fluorescence; dispersed LD.
Coal facies parameters were calculated from maceral data to interpret the depositional environment. The Texture Preservation Index (TPI) ranges widely (0.36–10.50, average 1.86). High TPI values indicate weak chemical degradation and mechanical fragmentation of plant tissues, corresponding to shallow water cover and oxidizing conditions. The Gelation Index (GI) varies significantly (0.25–6.73, average 3.39). High GI values reflect dominant gelification, associated with deep water cover, strongly reducing conditions, and stable water levels; low GI values suggest prevalent fusinitization, typically occurring under shallow, fluctuating water levels with oxidizing conditions. Most samples have a Vegetation Index (VI) > 1, indicating that coal-forming communities were dominated by woody plants. The Groundwater Flow Index (GWI) remains consistently low (0.00–1.55, average 0.37), implying limited groundwater disturbance during peat accumulation and relatively stable hydrodynamic conditions in the swamp.
Integrated analysis of GI-TPI and VI-GWI cross-plots (Figure a, b) identifies four main coal facies types (i.e., peat swamp types) in the study area. Dry Forest Peat Swamp (DFPS) is dominant. Most samples exhibit low GI, medium-high TPI, medium-high VI, and very low GWI. These characteristics, consistent with semifusinite dominance and high TPI/VI values, indicate a woody plant-dominated high-moor environment characterized by shallow water cover, periodic drying, and strong oxidation, likely due to recharge by atmospheric precipitation. These conditions favored the formation of fusinitized material (i.e., semifusinite) and the development of low-ash, low-sulfur coal.
3.
(a) GI-TPI cross-plot of Jurassic Yan’an Formation coal samples; (b) VI-GWI cross-plot of Jurassic Yan’an Formation coal samples.
In the samples range of this study, within Moist Forest Peat Swamp (MFPS), some samples exhibit medium-high GI, medium-low TPI, medium-low VI, and very low GWI. These features, which include increased vitrinite content (V/I > 1) and decreased inertinite (especially semifusinite), reflect deeper water cover, enhanced reducing conditions, more complete gelification, and the poorer plant tissue preservation (i.e., lower TPI) in forest swamps.
Shallow-Water Covered Forest Peat Swamp (SWCFPS) occurs in minor amounts, reflecting very deep-water cover and intense reducing conditions, with partial preservation of woody plant structures.
Wetland Herbaceous Peat Swamp (WLHPS) also occurs in minor amounts, characterized by very high vitrinite content (primarily desmocollinite) and very low inertinite content. These traits indicate deeply submerged, highly reducing conditions dominated by herbaceous/aquatic plants, with intense gelification and degradation of plant tissues.
In summary, coal seams of the Yan’an Formation in the Ningdong Coalfield formed in complex, dynamic peat swamp environments with significant spatial facies differentiation. The predominant DFPS indicates relatively well-drained, oxidized conditions with a low water table, supporting drought-tolerant gymnospermous vegetation under an oligotrophic to mesotrophic nutrient regime. In contrast, the MFPS reflects a higher, yet still shallow, water table that maintained sustained moisture and reducing conditions in the substrate, favoring the growth and preservation of moisture-loving tree ferns and gymnosperms. The sporadically developed WLHPS represents areas with prolonged shallow water coverage and higher nutrient availability, where herbaceous plants and reeds thrived. The rare SWCFPS records episodes of the highest water table within the swamp, where standing water inhibited forest regrowth but allowed for the accumulation and preservation of organic matter under anoxic, open-water conditions. Collectively, this facies differentiation was primarily controlled by the complex interplay of paleotopography, paleoclimate fluctuations, plant community composition, and the resultant acidic to neutral, oligotrophic to slightly eutrophic water conditions.
3.2. Influence of Coal Facies on Pores of Different Genetic Origins
Three main genetic types of pores were identified in the coal samples: primary pores, mineral-related pores, and metamorphic pores. Given that the selected samples have similar coal ranks, this section focuses on analyzing pore variations from the perspective of coal facies.
Primary pores mainly consist of interdetrital pores and cellular pores, with their pore spaces formed by the original plant cell structures and detrital particles (Figure a,b). Primary pores have diameters ranging from 0.17 to 30.71 μm (Figure c), and their development is jointly controlled by plant type and coal-forming environment. In WLHPS, the thin-walled parenchyma cells of herbaceous plantsunder weakly oxidizing conditionsreadily form large-aperture cellular pores, which are the most well-developed (mean diameter: 12.68 μm). By contrast, woody plants in DFPS, MFPS, and SWCFPS generally have thicker cell walls, resulting in smaller primary pore diameters. Overall, the average diameter of primary pores decreases when transitioning from WLHPS to the forest swamp facies (DFPS/MFPS/SWCFPS). Water cover depth has a relatively weak influence on the diameter of primary pores; under the influence of mechanical compaction during early coalification, the size of primary pores decreases as vitrinite reflectance (Ro) increases (Figure d).
4.
SEM images and aperture parameters of primary pores in Jurassic Yan’an Formation coal reservoirs. (a) SEM image of cellular pores. (b) SEM image of interdetrital pores. (c) Box plots of primary pore diameter in different coal facies. (d) Variation of primary pore diameter with Ro.
Mineral-related pores are dominated by intercrystalline pores and dissolution pores, while moldic pores are less developed. Intercrystalline pores primarily occur in crystalline minerals (e.g., quartz, pyrite) and amorphous inorganic minerals (e.g., some clays) (Figure a–d). Parallel-plate-shaped elongated pores often form between kaolinite minerals, and relatively isolated, large-aperture intracrystalline pores can form during the crystallization of pyrite or quartz (Figure e, f). Dissolution pores form within calcite, feldspar, and some soluble clay minerals, and most exhibit irregular shapes. Moldic pores are scarce; they mainly form as molds of hard minerals (e.g., pyrite, quartz) on the surfaces of vitrinite or inertinite macerals, typically appearing subcircular or square.
5.
SEM images showing mineral occurrence characteristics in Jurassic Yan’an Formation coal samples. (a) Clay mineral filling; (b) interparticle pores formed by calcite; (c) quartz filling; (d) calcite filling; (e) dolomite crystals; (f) quartz crystals.
The developmental characteristics of mineral-related pores are primarily controlled by the hydrodynamic conditions and sedimentary provenance determined by coal facies, with their diameters ranging from 0.28 to 22.65 μm (Figure a–c). WLHPS contains the most well-developed mineral-related pores (mean diameter: 12.36 μm)weak hydrodynamic conditions here favor the deposition of coarse-grained minerals (e.g., pyrite, quartz), forming large-aperture intercrystalline pores. DFPS has relatively well-developed dissolution pores: acidic conditions formed during periodic exposure of the peat swamp promote the dissolution of carbonate minerals (e.g., calcite), thereby generating dissolution pores.
6.
SEM images and diameter statistics of mineral-related pores. (a) SEM image of intercrystalline pores. (b) SEM image of moldic pores and dissolution pores. (c) Box plots of mineral-related pore diameter in different coal facies. (d) Variation of mineral-related pore diameter with Ro.
MFPS and SWCFPS are subject to enhanced hydrodynamic energy, which results in finer mineral grain sizes (predominantly fine-grained clay minerals) and significantly smaller diameters of mineral-related pores (mean: 3.17 μm in MFPS, 1.99 μm in SWCFPS). Moreover, the strongly reducing deep-water environments in these two facies promote extensive filling of pores by fine-grained clays, which severely block pore throats. Additionally, compaction during coal metamorphism further contributes to the decreasing trend in the diameters of mineral-related pores (Figure d).
Metamorphic pores mainly consist of clustered bubble-like pores on the surfaces of organic matter, with diameters concentrated in the range of 0.17–8.84 μm (Figure a,b). Hydrocarbon generation from hydrogen-rich liptinite (e.g., sporinite) in DFPS may lead to relatively larger pore diameters, while the strongly reducing environment in MFPS may promote higher pore density. Overall, coal facies have a nonsignificant controlling effect on the development of bubble-like pores; their formation is primarily governed by coalification processes (Figure c,d).
7.
SEM images and diameter statistics of metamorphic pores. (a) SEM image showing columnar-distributed gas pores. (b) SEM image showing clustered gas pores. (c) Box plots of pore diameter in different coal facies samples. (d) Variation of metamorphic pore diameter with Ro.
3.3. Influence of Coal Facies on Pore Structure
Coal facies control the development of pore structures in coal reservoirs. Low-field NMR results reveal that the pore structure of the Jurassic Yan’an Formation coal reservoirs is bimodal or trimodal, with micropores and transitional pores (0.5–2.5 ms), mesopores and macropores (20–50 ms), and fractures (>100 ms) all developed (Figure a and Table ).
8.
Variations in pore characteristics of Jurassic Yan’an Formation samples. (a) T2 spectra of different coal facies; (b) NMR pore size distribution of different coal facies; (c) specific surface area distribution of different coal facies, data from ref . (d) Pore volume distribution of different coal facies, data from ref .
2. Pore Parameters of Different Coal Facies .
| NMR
pore size distribution (%) |
Specifie
surface area (m2/g) |
Pore
volume (cm3/g) |
||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Coal Facies | Sample No. | Mac. | Mes. | Tra. | Mic. | Mac. | Mes. | Tra. | Mic. | Mes. and Mac. | Tra. | Mic. |
| WLHPS | ND-9 | 3.52 | 4.46 | 45.20 | 46.82 | 0.001 | 0.001 | 0.007 | 0.013 | 0.002 | 0.028 | 0.508 |
| ND-8 | 18.82 | 12.75 | 60.67 | 7.76 | 0.021 | 0.031 | 0.024 | 0.031 | 0.011 | 0.165 | 1.495 | |
| DFPS | ND-3 | / | / | / | / | 0.049 | 0.016 | 0.020 | 0.025 | 0.015 | 0.251 | 0.916 |
| ND-6 | 13.76 | 15.57 | 57.29 | 13.38 | 0.005 | 0.019 | 0.039 | 0.038 | 0.012 | 0.160 | 3.766 | |
| ND-10 | 13.40 | 13.43 | 63.55 | 9.62 | 0.007 | 0.035 | 0.037 | 0.058 | 0.002 | 0.032 | 4.125 | |
| ND-4 | 11.95 | 23.98 | 54.21 | 9.85 | 0.051 | 0.032 | 0.027 | 0.023 | 0.005 | 0.061 | 3.486 | |
| MFPS | ND-5 | 15.82 | 27.48 | 47.31 | 9.38 | 0.007 | 0.032 | 0.037 | 0.060 | 0.001 | 0.034 | 2.738 |
| ND-13 | / | / | / | / | 0.010 | 0.055 | 0.051 | 0.027 | 0.015 | 0.218 | 4.412 | |
| SWCFPS | ND-12 | 19.43 | 22.89 | 50.13 | 7.55 | 0.034 | 0.061 | 0.031 | 0.034 | 0.018 | 0.267 | 3.103 |
Note: Mac. stands for macropores. Mes. stands for mesopores. Tra. stands for transition pores. Mic. stands for micropores. “/” means no data.
The specific surface area (SSA) of Yan’an Formation coal ranges from 0.54 to 4.65 m2/g (average 2.78 m2/g), primarily contributed by micropores. Plant type differences also influence SSA differentiation. Forest swamp facies generally exhibit higher SSA than WLHPS. Water cover indirectly regulates micropore development by affecting organic matter decomposition, though the differences are not significant.
Correlation analysis was conducted between coal facies parameters and pore parameters (Figure ). TPI and VI exhibit: (1) a strong positive correlation with SSA (r = 0.62–0.63); (2) a negative correlation with micropore volume (r = −0.23 to −0.25). This confirms that increased plant input promotes the development of micropores, while aromatization during coalification inhibits the volumetric expansion of micropores.
9.
Correlation analysis between coal facies parameters and pore parameters.
GWI (related to water cover conditions) exhibits: (1) a positive correlation with mesopore volume (r = 0.34); (2) a negative correlation with macropore volume (r = −0.30). Strongly reducing environments (associated with high GWI) facilitate mesopore formation (driven by gelification and microbial degradation), whereas sustained mineral filling under prolonged water cover significantly compresses macropore space.
GI exhibits: (1) a strong positive correlation with macropore volume (r = 0.55); (2) a weak positive correlation with total pore volume (r = 0.20); (3) a negative correlation with transitional pore volume (r = −0.26). Intense gelification in high-GI environments (e.g., SWCFPS) forms connected macropore systems (with a honeycomb structure), which dominate the contribution to total pore volume. In summary, coal facies control the distribution, pore volume, and SSA characteristics of coal from the Yan’an Formation, thereby exerting a profound influence on reservoir physical properties.
3.4. Pore-Fracture Development Model Constrained by Coal Facies
As a product of specific peat swamp environments, coal facies exert a fundamental control on the formation and evolution of pore-fracture systems during coalification and diagenesis. Based on coal facies classifications within the Yan’an Formation of the Ningdong Coalfield, and supported by microscopic observations and CT 3D reconstruction, this study analyzes pronounced differences in fracture development across various coal facies. The results of this analysis are applicable to samples with sedimentary environments and coal ranks similar to those in the study area.
Fractures in the Yan’an Formation coal samples are categorized into four morphological types: dendritic, irregular reticulated, stepping, and isolated (Figure ). Typically, fracture widths are below 5 μm, and lengths are under 300 μm. Larger fractures are commonly filled with liptinite macerals (such as waxes, resins, sporinite, and alginite), which are complex organic compounds that exhibit intense yellow or green fluorescence under blue-light excitation. Some fractures are filled with minerals and show no fluorescence.
10.
Microscopic fracture characteristics in Jurassic Yan’an Formation coal samples. (a) Dendritic fracture (white light); (b) fluorescence of (a); (c) dendritic fracture; (d) irregular reticulated fracture; (e) fluorescence of (d); (f) isolated fracture; (g) fluorescence of (f); (h) stepping fracture; (i) fluorescence of (h). Polished sections, reflected fluorescence, blue-light excitation.
WLHPS exhibits moderately developed fractures, generally with poor connectivity (Figure a,b). Dominated by inertinite, WLHPS shows prevalent shrinkage fractures, particularly around inertodetrinite. The brittleness of fusinite and semifusinite promotes short, tortuous, and isolated shrinkage fractures with low connectivity (Figure c,d). Low vitrinite content restricts the development of large-scale endogenous cleats. Higher mineral content occupies pore space and suppresses primary porosity; diagenetic shrinkage or differential compaction leads to boundary microfractures. CT scans indicate significant mineral filling along bedding planes, the lowest porosity (13.51%), and low isolated porosity, collectively resulting in limited connectivity (Table ).
11.
3D CT reconstructions of typical Yan’an Formation samples. (A) 3D reconstruction model of different coal facies samples, with the gray, blue, and yellow colors representing the matrix, fractures/pores, and minerals, respectively. (B) Pore-fracture structure of different coal facies, with colors representing different pore sizes. (C) Mineral distribution in different coal facies, with colors representing different mineral sizes. (D) Ball-and-stick models of different coal facies samples.
DFPS displays highly developed fractures with good connectivity (Figure e,f,i,j). This facies provides favorable conditions for both endogenous cleats (forming regular reticulated patterns) and exogenous fractures. Shrinkage fractures, especially within fusinite cell cavities, are prominent. High inertinite content (mainly fusinite) and a rigid, brittle structure facilitate the development of dense, well-connected endogenous cleat systems under coalification shrinkage and tectonic stress (Figure h,l). Oxidative conditions promote fusinitization of primary tissues, establishing a foundation for fracture development. Mineral filling in primary pores or along bedding planes later generates microfractures at mineral grain or bedding boundaries (Figure g,k). CT reconstruction reveals a reticulate or flaky distribution of minerals, moderate porosity (ND-03:14.87%; ND-10:14.53%), and a layered distribution of connected pore-fractures (Table ).
3. Porosity Parameters of Typical Samples from CT Analysis.
| Sample No. | Coal Facies | Porosity (%) | Connected Porosity (%) | Connectivity Direction | Isolated Porosity (%) |
|---|---|---|---|---|---|
| ND-08 | WLHPS | 13.51 | 11.87 | X, Y, Z | 1.69 |
| ND-03 | DFPS | 14.87 | 12.85 | X, Y, Z | 2.01 |
| ND-10 | 14.53 | 12.29 | X, Y, Z | 2.24 | |
| ND-13 | MFPS | 18.56 | 16.39 | X, Y, Z | 2.17 |
MFPS exhibits moderate to well-developed endogenous fractures (cleats), typically with high connectivity (Figure m,n). Regular endogenous cleats (face and butt cleats) serve as the primary storage and seepage pathways; microfractures are also observable within desmocollinite. High vitrinite content undergoes volumetric shrinkage during coalification, forming regular cleat networks; moderate gelification produces a homogeneous matrix conducive to cleat development (Figure p). CT scans show well-connected pore-fracture systems, sporadic mineral distribution, and the highest porosity among the facies (Figure o and Table ).
In summary, coal facies systematically govern the type (including shrinkage fractures, endogenous cleats, and mineral-related fractures), scale, geometry, and connectivity of pore-fracture systems through core maceral composition (such as the vitrinite/inertinite ratio and maceral types) and the degree of gelification. DFPS is characterized by a highly interconnected cleat system, MFPS develops relatively regular and connected cleats, while WLHPS exhibits poor connectivity due to dominant inertinite-related shrinkage fractures and mineral influences. Mineral filling is a key factor contributing to reservoir heterogeneity and permeability reduction.
3.5. Mechanical Characteristics of Coal Influenced by Coal Facies
Experimental results demonstrate systematic variations in mechanical parameters (elastic modulus, Poisson’s ratio, tensile strength) across coal facies, significantly influenced by mineral content and type.
WLHPS exhibits the highest average elastic modulus (4.45 GPa), notably surpassing those of the forest swamp facies (Table and Figure a). Among the forest swamp facies, the elastic modulus decreases systematically with increasing water cover depth: DFPS (2.80 GPa) > MFPS (2.28 GPa) > SWCFPS (1.51 GPa). A similar decreasing trend in tensile strength with deeper water cover is observed in forest swamp facies. Poisson’s ratio is highest in DFPS (0.39–0.48), intermediate in MFPS (0.42–0.46), and relatively low in both WLHPS (0.36–0.39) and SWCFPS (0.31) (Figure b).
4. Mechanical Property Parameters of Yan’an Formation Coal Reservoir.
| Coal Facies | Sample No. | Confining Pressure (MPa) | Differential Stress (MPa) | Elastic Modulus (GPa) | Poisson’s Ratio | Tensile Strength (MPa) |
|---|---|---|---|---|---|---|
| WLHPS | ND-8 | 6 | 69.45 | 5.59 | 0.39 | 1.75 |
| ND-9 | 65.31 | 3.31 | 0.36 | 1.52 | ||
| DFPS | ND-3 | 70.72 | 3.54 | 0.48 | 1.83 | |
| ND-4 | 73.85 | 2.7 | 0.39 | 1.76 | ||
| ND-10 | 48.07 | 2.17 | 0.47 | 1.82 | ||
| MFPS | ND-5 | 68.16 | 2.68 | 0.46 | 1.81 | |
| ND-13 | 32.23 | 1.82 | 0.42 | 1.79 | ||
| SWCFPS | ND-12 | 69.12 | 1.51 | 0.31 | 1.38 |
12.
Mechanical parameters and mineral contents of different coal facies samples. (a) Distribution maps of elastic modulus in different coal facies. (b) Distribution maps of Poisson’s ratio in different coal facies. (c) Distribution maps of tensile strength in different coal facies. (d) Distribution maps of whole-rock minerals in different coal facies.
These mechanical properties show strong correlations with the mineralogical composition of each coal facies (Figure c,d). The systematic decline in elastic modulus and tensile strength from DFPS to SWCFPS is directly attributed to a substantial reduction in rigid mineral content (e.g., calcite and pyrite). These minerals possess high elastic modulus and strength, and their networked distribution forms a rigid framework within the coal matrix, effectively inhibiting crack propagation and enhancing macroscopic stiffness and strength. The high elastic modulus observed in WLHPS sample ND-8, which is rich in calcite and pyrite, clearly illustrates this effect.
Conversely, an increase in clay mineral content, while adding to total mineral volume, reduces overall coal strength and stiffness due to the inherently low strength of clay minerals, water-absorption softening, and interlayer slip. This results in decreased elastic modulus and tensile strength, along with an enhanced capacity for plastic deformation (reflected in higher Poisson’s ratio). For example, WLHPS sample ND-9, which contains only amorphous minerals and 30% clay, shows significantly lower tensile strength compared to the rigid-mineral-rich ND-8. SWCFPS, dominated by amorphous organic matter with minimal mineral content, lacks support from a rigid mineral framework, leading to the lowest elastic modulus and strength among the facies.
Coal facies exert a fundamental control on mechanical behavior through their distinct mineral-organic assemblages. As facies evolve from DFPS to SWCFPS, a pronounced decrease in rigid minerals leads to systematic reductions in elastic modulus and tensile strength. Poisson’s ratio is coinfluenced by mineral type and the homogeneity of organic matter.
4. Conclusions
-
(1)
The Yan’an Formation in the Ningdong Coalfield is predominantly composed of DFPS, followed by MFPS, with limited development of SWCFPS and WLHPS. Facies differentiation is governed by water depth, redox conditions, and paleovegetation type within the peat swamp environment.
-
(2)
Coal facies exert a significant influence on pore types through their control over organic material composition and depositional conditions. Forest swamp facies (DFPS, MFPS, SWCFPS) display higher pore volumes (0.12–0.16 cm3/g), which increase with greater water cover and enhanced reducing conditions. Specific surface area (SSA) shows a strong positive correlation with woody plant input (reflected by TPI and VI, r = 0.62–0.63), although micropore development is somewhat inhibited by aromatization processes in higher plants.
-
(3)
The high inertinite content in DFPS contributes to a well-connected cleat system, showing an average CT-connected porosity of 12.57%. In MFPS, the dominance of vitrinite promotes the development of regular cleat networks with enhanced connectivity (16.39% porosity), supported by a homogeneous matrix. In contrast, WLHPS exhibits the poorest connectivity due to mineral filling and the prevalence of isolated shrinkage cracks, which suppress effective pore-fracture development.
-
(4)
Coal mechanical properties are primarily governed by mineral assemblages, which are in turn controlled by coal facies. Therefore, coal mechanical properties decrease significantly with increasing water cover depth and reduced content of rigid minerals such as calcite and pyrite. Poisson’s ratio is coregulated by mineral type and the homogeneity of the organic matter.
Acknowledgments
This work was supported by the National Major Special Project “Evaluation and Stereoscopic Development Technology for Coalbed Methane in Thin Reservoirs” (Grant No. 2025ZD1404204) and by the Ningxia unconventional natural gas exploration and development innovation team (Grant No. ZRCTD2023002). The authors also extend their gratitude to the reviewers and editors for their valuable comments and suggestions, which greatly contributed to enhancing the quality of this manuscript.
The authors declare no competing financial interest.
References
- Li Z., Chen S., Tang D., Zhi Y.. Genesis and accumulation modes of coalbed methane at the eastern margin of Ordos Basin, China: Evidence from Its geochemistry. ACS Omega. 2024;9(45):45421–45436. doi: 10.1021/acsomega.4c07416. [DOI] [PMC free article] [PubMed] [Google Scholar]
- Liu Z., Zhao S., Hu Z., Shen B., Feng D., Zhang J., Ye J., Ma C., Dong Z.. Characteristics and controlling factors of coal-measure unconventional reservoirs–A case study of the Carboniferous-Permian in the Ordos Basin. Unconv. Resour. 2025;6:100153. doi: 10.1016/j.uncres.2025.100153. [DOI] [Google Scholar]
- Wang B., Huang Y., Zhang D., Wang H., Zheng X., Liu J., Wang L., Huang W., Chen X., Hu W.. et al. Numerical modeling of deep coalbed methane accumulation in the central-eastern Ordos Basin, China. Nat. Gas Ind. B. 2024;11(4):405–419. doi: 10.1016/j.ngib.2024.08.002. [DOI] [Google Scholar]
- Du F., Ning S., Liu C., Li C., Qiao J., Tan F., Luo Z.. Petrographical and geochemical characterization of the inertinite-rich coal from the Ningdong Coalfield, Northwest Ordos Basin, China. Arabian J. Geosci. 2019;12(2):36. doi: 10.1007/s12517-018-4174-2. [DOI] [Google Scholar]
- Jia B., Li S., Lin H., Chen D., Zhang J.. Quantitative sources identification of gas emissions in mined-out area of coal seams in the Huanglong coalfield of the Ordos Basin, China. Sci. Rep. 2025;15(1):26731. doi: 10.1038/s41598-025-10816-2. [DOI] [PMC free article] [PubMed] [Google Scholar]
- Ye J., Zhang Y., He W., Tao R., Tao S., Chen S., Cui Y., Wang Q.. Elemental Geochemical Distribution of the Jurassic Yan’an Formation in the Ningdong Coalfield and its Controlling Effect on Coal Reservoir Properties. Nat. Resour. Res. 2023;32(3):1299–1318. doi: 10.1007/s11053-023-10190-8. [DOI] [Google Scholar]
- He J., Li Z., Zhang X., Wang H., Dong W., Du E., Chang S., Ou X., Guo S., Tian Z.. et al. Towards carbon neutrality: A study on China’s long-term low-carbon transition pathways and strategies. Environ. Sci. Ecotechnol. 2022;9:100134. doi: 10.1016/j.ese.2021.100134. [DOI] [PMC free article] [PubMed] [Google Scholar]
- Wang S., Liu L., Zhu M., Shen Y., Shi Q., Sun Q., Fang Z., Ruan S., He W., Yang P.. et al. New way for green and low-carbon development of coal industry under the target of “daul-carbon”. J. China Coal Soc. 2024;49(1):152–171. doi: 10.13225/j.cnki.jccs.YH23.1690. [DOI] [Google Scholar]
- Guo H., Yuan L., Cheng Y., Wang K., Xu C.. Experimental investigation on coal pore and fracture characteristics based on fractal theory. Powder Technol. 2019;346:341–349. doi: 10.1016/j.powtec.2019.02.026. [DOI] [Google Scholar]
- Liu X., Nie B., Guo K., Zhang C., Wang Z., Wang L.. Permeability enhancement and porosity change of coal by liquid carbon dioxide phase change fracturing. Eng. Geol. 2021;287:106106. doi: 10.1016/j.enggeo.2021.106106. [DOI] [Google Scholar]
- Wang D., Xiaorui T., Wei J., Zhang H., Yao B., Zhang H., Chen C.. Fracture evolution and nonlinear seepage characteristic of gas-bearing coal using X-ray computed tomography and the lattice Boltzmann method. J. Pet. Sci. Eng. 2022;211:110144. doi: 10.1016/j.petrol.2022.110144. [DOI] [Google Scholar]
- Zhao Y., Wang C., Ning L., Zhao H., Bi J.. Pore and fracture development in coal under stress conditions based on nuclear magnetic resonance and fractal theory. Fuel. 2022;309:122112. doi: 10.1016/j.fuel.2021.122112. [DOI] [Google Scholar]
- Diessel, C. F. K. Coal facies and depositional environment Coal-Bearing Depositional Systems Springer; Berlin, Heidelberg: 1992. 161–264 10.1007/978-3-642-75668-9_5 [DOI] [Google Scholar]
- Xiao C., Han D., Zhang J., Chen S., Qin Z., Vandeginste V.. Effect of Coal Rank and Coal Facies on Nanopore–Fracture Structure Heterogeneity in Middle-Rank Coal Reservoirs. ACS Omega. 2024;9(30):33279–33292. doi: 10.1021/acsomega.4c05179. [DOI] [PMC free article] [PubMed] [Google Scholar]
- Wang Y., Cheng H.. Advances in microscopic pore structure characterization of fine-grained mudrocks. Energy Fuels. 2023;37(3):1495–1510. doi: 10.1021/acs.energyfuels.2c03144. [DOI] [Google Scholar]
- Mou P., Pan J., Niu Q., Wang Z., Li Y., Song D.. Coal pores: Methods, types, and characteristics. Energy Fuels. 2021;35(9):7467–7484. doi: 10.1021/acs.energyfuels.1c00344. [DOI] [Google Scholar]
- Zhao D., Guo Y., Wang G., Mao X.. Characterizing nanoscale pores and its structure in coal: Experimental investigation. Energy Explor. Exploit. 2019;37(4):1320–1347. doi: 10.1177/0144598719831397. [DOI] [Google Scholar]
- Tao S., Chen S., Tang D., Zhao X., Xu H., Li S.. Material composition, pore structure and adsorption capacity of low-rank coals around the first coalification jump: A case of eastern Junggar Basin, China. Fuel. 2018;211:804–815. doi: 10.1016/j.fuel.2017.09.087. [DOI] [Google Scholar]
- Dai S., Bechtel A., Eble C. F., Flores R. M., French D., Graham I. T., Hood M. M., Hower J. C., Korasidis V. A., Moore T. A.. et al. Recognition of peat depositional environments in coal: A review. Int. J. Coal Geol. 2020;219:103383. doi: 10.1016/j.coal.2019.103383. [DOI] [Google Scholar]
- Nie B., Liu X., Yang L., Meng J., Li X.. Pore structure characterization of different rank coals using gas adsorption and scanning electron microscopy. Fuel. 2015;158:908–917. doi: 10.1016/j.fuel.2015.06.050. [DOI] [Google Scholar]
- Zhifei L., Yingchun W., Shuzheng N., Xu J., Rongfang Q., Daiyong C.. The differences of element geochemical characteristics of the main coal seams in the Ningdong coalfield, Ordos Basin. J. Geochem. Explor. 2019;202:77–91. doi: 10.1016/j.gexplo.2019.03.018. [DOI] [Google Scholar]
- Li Y., Yan M., Liu P., Lin H., Li S., Huo S., Yang T.. Characteristics of the tectonic background and sedimentary paleoenvironment of coal-bearing strata from the Yan’an formation in the Ordos basin: Evidence from the geochemistry of major and trace elements. ACS Earth Space Chem. 2022;6(11):2680–2697. doi: 10.1021/acsearthspacechem.2c00240. [DOI] [Google Scholar]
- Zhifei L., Yingchun W., Fanghui H., Luoping M., Xu J., Rongfang Q., Daiyong C.. Control of accommodation changes over coal composition: Case study of Jurassic medium-thick coal seams in the Ordos Basin, China. Arab J Geosci. 2020;13(5):203. doi: 10.1007/s12517-020-5205-3. [DOI] [Google Scholar]
- Mao X., Liu J., Yu Y., Ma Y., Huang P.. Study on Coal Controlling Structural Features and Development Pattern in Ningdong Coalfield. Coal Geol. China. 2020;32(12):22–26. [Google Scholar]
- Liu K., Cao D., Gao K., Zhang Q., Ma Z.. Study on differentiation cause about tectonic evolution of northern and southern segments in Ningdong Coalfield. Coal Sci. Technol. 2017;45(6):157–164. [Google Scholar]
- Chen H., Tian W., Chen Z., Zhang Q., Tao S.. Genesis of coalbed methane and its storage and seepage space in Baode Block, Eastern Ordos Basin. Energies. 2022;15(1):81. doi: 10.3390/en15010081. [DOI] [Google Scholar]












