Skip to main content
Wiley Open Access Collection logoLink to Wiley Open Access Collection
. 2026 Jul 10;65(38):e5216345. doi: 10.1002/anie.5216345

Central Core Engineering of Aromatic Carbonyl Molecules Enables Highly Efficient and Stable Perovskite Solar Cells

Guangyue Yang 1,2, Yu Lei 1, Panyu Wang 1, Yue Qiang 3, Bingqian Zhang 2, Na Shi 1, Likai Zheng 4, Shiwei Liu 1,5,✉, Shuping Pang 2,✉, Xin Guo 6,✉, Xiaoqing Jiang 2,✉
PMCID: PMC13573151  PMID: 42429127

ABSTRACT

Aromatic carbonyl molecules have emerged as highly effective passivation additives for fabricating efficient and stable perovskite solar cells. However, the influence of variations in the central core structure of aromatic carbonyl molecules on the passivation capability of their carbonyl groups remains insufficiently explored, thereby hindering the rational design of aromatic carbonyl‐based passivation additives. To address this limitation, we employed a central‐core engineering strategy to design three structurally similar molecules with different core groups. Through systematic investigation, we found that enhancing the electron‐donating ability of the molecular core increases the electron density on the carbonyl groups, thereby improving their defect‐passivation effectiveness. Consequently, perovskite solar cells incorporating TBPAA with the most electron‐rich core delivered power conversion efficiencies of 26.12% (0.09 cm2) and 22.41% (14.0 cm2), while retaining 95% of their initial efficiency after 1200 h of continuous maximum power point tracking at a temperature of 65°C under 1‐sun illumination (ISOS‐L‐2). This work highlights the critical role of the molecular central core in defect passivation and offers new molecular design guidelines for the development of highly efficient and long‐term stable perovskite photovoltaics.

Keywords: carbonyl, central core groups, passivation, perovskite, solar cells


Enhancing the electron‐donating strength of aromatic cores boosts carbonyl defect passivation in perovskite films. Perovskite solar cells treated with TBPAA, the molecule with the most electron‐rich core, achieve 26.12% (0.09 cm2) and 22.41% (14.0 cm2), highlighting the critical role of core design in device performance and stability.

graphic file with name ANIE-65-e5216345-g003.webp

1. Introduction

Perovskite solar cells (PSCs) have attracted considerable attention due to their outstanding power conversion efficiencies [1, 2, 3]. However, perovskite films inevitably contain a high density of defects at surfaces and grain boundaries. These defects act as non‐radiative recombination centers, leading to significant open‐circuit voltage losses, and also serve as channels for ion migration, accelerating device degradation [4, 5, 6]. These issues severely limit both device efficiency and long‐term stability.

To address these issues, a variety of passivation strategies have been developed [7, 8, 9]. Among them, carbonyl‐containing molecules have attracted considerable attention because of their facile availability and strong coordination capability with undercoordinated Pb2+ ions in perovskite films, which enables modulation of crystal growth and suppression of defect formation [10, 11, 12]. Numerous studies have demonstrated the superior effectiveness of carbonyl groups in passivating defects in perovskite films, even when the carbonyl groups are grafted onto different substituents [6, 13, 14]. However, most reported works concentrate on the passivation effects of carbonyl groups themselves, largely neglecting the critical influence of the central core structure on the passivation capability of the carbonyl groups [15, 16, 17]. This oversight hampers the further optimization and rational design of carbonyl‐based passivation molecules, despite their inherent potential for strong coordination with undercoordinated Pb2+ defects.

Herein, we designed three carbonyl‐based passivation molecules containing three carbonyl groups while differing in their central core structures, including benzene‐1,3,5‐tricarbaldehyde (TMA), tris(4‐formylphenyl)amine (TFPA), and tris([1,1′‐biphenyl]‐4‐carbaldehyde)amine (TBPAA), presented in Figure S1. These aromatic carbonyl molecules were introduced as additives to passivate defects and enhance the overall quality of the perovskite films, as illustrated in Figure 1a. The results show that as the electron‐donating ability of the central core gradually increases, the electron density on the carbonyl groups is correspondingly enhanced, leading to progressively stronger defect passivation. Consequently, the device employing TBPAA with the strongest electron‐donating central core achieved a remarkable power conversion efficiency of 26.12% and retained 95% of its initial performance after 1200 h of continuous maximum‐power‐point operation, demonstrating exceptional operational stability. Furthermore, the mini‐module (14.0 cm2) incorporating TBPAA achieved an impressive PCE of 22.41%. This study establishes a clear correlation between the electron‐donating ability of the central core and the passivation strength of carbonyl groups, offering a new molecular‐design strategy for developing high‐performance carbonyl‐based passivators for perovskite photovoltaics.

FIGURE 1.

FIGURE 1

(a) Schematic diagram of defects in molecularly passivated perovskite. (b) Calculated ESP profiles for TMA, TFPA, and TBPAA molecules. (c) the interaction energy (Eint) of TMA, TFPA, and TBPAA with VI defect sites on the surface of perovskite. Charge difference plot of TMA (d), TFPA (e), and TBPAA (f) on perovskite surfaces interacting with undercoordinated Pb2+.

2. Results and Discussion

Density functional theory (DFT) calculations were employed to analyze the electrostatic potential (ESP) distributions of molecules with different central core structures (Figure 1b). The results indicate that as the electron‐donating ability of the central core increases, the negative potential regions around the oxygen atoms of TMA, TFPA, and TBPAA gradually decrease (−0.181, −0.198, and −0.275 eV, respectively), suggesting strong local electron enrichment, which facilitates coordination with Pb2+ [16]. The ESP analysis indicates that the aromatic carbonyl compound TBPAA, featuring the most electron‐rich central core, is expected to interact most strongly with defects in perovskite films, particularly undercoordinated Pb2+ defects [17]. Subsequent DFT calculations based on the Vienna ab initio simulation package (VASP) were carried out to quantify the interaction energy (Eint) between the additive molecules and the undercoordinated iodine vacancy (VI) defects in the perovskite film, thereby providing further support for the proposed interaction mechanism [18]. As shown in Figures 1c and S2; Table S1, TBPAA shows the strongest interaction with undercoordinated Pb2+ defects, with an Eint of −0.718 eV, exceeding those of TFPA (−0.629 eV) and TMA (−0.448 eV). As shown in the charge density difference plots (Figure 1d–f), TBPAA with the most electron‐rich central core demonstrates the most pronounced electron transfer to undercoordinated Pb2+ defects, confirming its superior defect‐passivation capability among the three molecules [19].

To further verify the reliability of the DFT calculations, Fourier‐transform infrared spectroscopy (FTIR) was employed to probe the interactions between the carbonyl groups (─C═O) of the additive molecules and undercoordinated Pb2+ defects in the perovskite films. As shown in Figure 2a–c, the ─C═O stretching vibration of TBPAA exhibited a pronounced redshift from 1701 cm−1 to 1679 cm−1 (∆ν = 22 cm−1), which is significantly larger than the shifts observed for TFPA (from 1709 to 1694 cm−1, ∆ν = 15 cm−1) and TMA (from 171 to 1709 cm−1, ∆ν = 9 cm−1). These FTIR results indicate that TBPAA exhibits the strongest coordination interaction with undercoordinated Pb2+ ions among the three molecules [20]. To further elucidate the interaction between the additives and Pb2+ defects, x‐ray photoelectron spectroscopy (XPS) was performed on perovskite films before and after treatment with the carbonyl compounds. All samples treated with aldehyde compounds exhibited a distinct O 1s characteristic peak at approximately 530.8 eV (Figure S3). More importantly, compared to TMA and TFPA, the O 1s peak of the TBPAA‐treated film shifted by 0.35 eV toward higher binding energy. This indicates that more electrons are transferred from the oxygen atom to the electron‐deficient Pb2+, forming a stronger coordination bond [21]. As shown in Figure 2d, the Pb 4f peaks of the TBPAA‐treated perovskite film exhibited the largest shift of 0.41 eV compared to the pristine film, significantly exceeding the shifts observed for TFPA‐ (0.32 eV) and TMA‐ (0.25 eV) treated films. Additionally, although triphenylamine (TPA) can also provide lone pair electrons to interact with lead, its effect is significantly weaker than that of all aromatic aldehyde‐containing molecules, such as TFPA. (Figure S4) The coordination bond between C═O and uncoordinated Pb2+ is the key factor dominating defect passivation. Meanwhile, the I 3d peaks of the perovskite films treated with the same carbonyl compounds exhibited similar shifts (Figure S5). These XPS results indicate that among the carbonyl additives, TBPAA, with the most electron‐donating central core, exhibits the strongest ability to increase the electron density around the Pb and I species in the perovskite films, demonstrating its superior defect‐passivation capability [22]. A detailed analysis of the XPS results shows that the I/Pb atomic ratios of the perovskite films increase after additive treatment (Figure S6). The ratios rise from 3.32:1 for the pristine film to 3.41:1, 3.43:1, and 3.51:1 for TMA‐, TFPA‐, and TBPAA‐treated films, respectively. The highest I/Pb ratio observed for the TBPAA‐treated perovskite film indicates that the carbonyl additives, particularly TBPAA, effectively suppress the formation of volatile I0 species at the film surface. This effect can be attributed to the enhanced electron‐donating ability of the central core, which improves their defect‐passivation capability [23].

FIGURE 2.

FIGURE 2

FTIR spectra of pristine TMA and PbI2‐TMA (a), TFPA and PbI2‐TFPA (b), as well as TBPAA and PbI2‐TBPAA (c) films. (d) Pb 4f XPS spectra of perovskite films without and with TMA, TFPA, and TBPAA passivation. (e–h) GWIAXS patterns of perovskite films without and with TMA, TFPA, and TBPAA passivation. (i–l) Top‐view SEM images of perovskite films.

To elucidate the role of aromatic carbonyl additives with different core structures in regulating the crystallization behavior of perovskite thin films, X‐ray diffraction (XRD) measurements were conducted. As shown in Figure S7, the incorporation of these additives, particularly the TBPAA molecule, leads to a notable enhancement of the (100) diffraction peak intensity compared to the untreated perovskite film, indicating that carbonyl‐containing molecules with strongly electron‐donating core structures effectively improve the crystallinity of the perovskite films. Grazing‐incidence wide‐angle x‐ray scattering (GIWAXS, Figures 2e–h and S8) measurements were further performed to validate the above results. Compared to the control, TMA‐, and TFPA‐treated perovskite films, the TBPAA‐treated film exhibits enhanced diffraction intensity primarily along the out‐of‐plane (qz) direction (corresponding to the (100) plane) at q≈1 Å−1, indicating a stronger preferential orientation, consistent with the XRD results shown in Figure S5. These XRD characterization results indicate that the introduction of aromatic carbonyl additives, particularly TBPAA with strongly electron‐donating central cores, effectively promotes the crystallization of perovskite films and the vertical growth of the crystals [24]. In addition, scanning electron microscopy (SEM) was employed to investigate the surface morphologies of the perovskite films before and after incorporating aromatic carbonyl additives (Figures 2i–l and S9). The SEM results clearly reveal that the introduction of additives results in a pronounced enlargement of the perovskite crystal domains. Moreover, the average grain size exhibits a positive correlation with the electron‐donating strength of the central core in the aromatic carbonyl additives, increasing from 1.36 µm for the control film to 1.58, 1.69, and 1.91 µm for the TMA‐, TFPA‐, and TBPAA‐treated films, respectively [25]. The impact of aromatic carbonyl additive treatment on the surface morphology of perovskite films was evaluated using atomic force microscopy (AFM). As illustrated in Figures S10 and S11, the root‐mean‐square (RMS) roughness of the films decreased progressively upon additive incorporation. Specifically, the RMS roughness values dropped from 53.4 nm for the pristine film to 47.7, 42.3, and 32.8 nm for the TMA‐, TFPA‐, and TBPAA‐treated films, respectively. These results indicate that the additives, particularly TBPAA, lead to smoother film surfaces, which is consistent with the observed enhancement in crystal domain size and improved film quality. To gain deeper insight into the distribution of aromatic carbonyl additives within perovskite films and the underlying mechanism by which they influence film properties, time‐of‐flight secondary ion mass spectrometry (TOF‐SIMS) was employed to precisely show the localization of TMA, TFPA, and TBPAA throughout the films [26]. As shown in Figure S12, which were obtained by monitoring the characteristic ion fragments of C9H6O3 +, C21H15NO3 +, and C26H18NO3 + for TMA, TFPA, and TBPAA, respectively, the additive molecules were predominantly enriched at the top surface and within the bulk region of the perovskite films after crystallization. Unlike the other two additives, TBPAA exhibited the most uniform and widespread distribution throughout the film. This homogeneous distribution not only facilitates the optimization of the perovskite crystal structure but also more effectively suppresses the formation of undercoordinated Pb2+ defects, thereby significantly reducing the overall defect density of the film.

We conducted in situ photoluminescence (PL, Figure S13) measurements to investigate the nucleation and crystallization processes during the antisolvent bath. When the film was immersed in anisole, both the control and experimental groups exhibited PL peaks in the 700–800 nm wavelength range, corresponding to nanoscale perovskite crystals [27]. The introduction of additives suppressed the nucleation process of perovskites, thereby promoting the formation of larger grains. Compared to control, TMA, and TFPA, TBPAA demonstrated a more pronounced promoting effect [28].

Ultraviolet–visible (UV–vis, Figure S14), steady‐state, and transient photoluminescence (PL, Figure S15) measurements were conducted to evaluate the effect of aromatic carbonyl additives on the optical bandgap of the perovskite films. The absorption edges and PL peak positions remained largely unchanged for both the control and modified films, indicating that the optical bandgap was minimally affected. Moreover, the PL intensity was further enhanced upon the introduction of aromatic aldehyde molecules, indicating that these additives, particularly TBPAA, effectively passivate defects in the perovskite films, thereby suppressing non‐radiative recombination [29].

Time‐resolved photoluminescence (TRPL) measurements further confirmed these results, providing direct evidence of the improved carrier lifetime (Figure S16 and Table S2). The average carrier lifetimes of TMA‐, TFPA‐, and TBPAA‐modified perovskite films were 120.4, 149.1, and 195.8 ns, respectively, markedly exceeding that of the control (82.4 ns) [30]. To further visualize the effect of aromatic aldehyde molecules on defect states, two‐dimensional (2D) PL mapping was conducted. As shown in Figure 3a–d, the incorporation of aromatic aldehyde additives markedly enhanced the PL intensity across the films. Among the additives, TBPAA demonstrated the most effective passivation, outperforming TFPA, TMA, and the pristine film. This superior performance is attributed to the enhanced electron‐donating capacity of the central core in TBPAA, which effectively strengthens the passivation ability of the carbonyl functional groups and suppresses defect formation in the perovskite films.

FIGURE 3.

FIGURE 3

(a–d) 2D PL intensity spectra of perovskite films without and with TMA, TFPA, and TBPAA. (e–h) Conductive AFM current mapping images of perovskite films. Iavg represents the average current across the current mapping images. The perovskite films were prepared on the SnO2‐coated FTO glass. (i–l) KPFM images of control, TMA, TFPA, and TBPAA perovskite films. (m) Histogram of interfacial potential distribution by passivated perovskite KPFM results. (n) Schematic diagrams of energy levels of perovskites determined from UPS measurements.

To further verify the impact of these introduced additives on the local electrical properties of the perovskite films, conductive atomic force microscopy (C‐AFM) was employed. As shown in Figure 3e–h, the average current (Iavg) across the film surface increased from 21.3 pA for the control to 41.4, 63.8, and 82.6 pA for the TMA‐, TFPA‐, and TBPAA‐treated films, respectively [31]. To elucidate the electronic structure modifications induced by the additives, surface potential and energy band alignment were characterized using Kelvin probe force microscopy (KPFM) and ultraviolet photoelectron spectroscopy (UPS). KPFM measurements (Figures 3i–l and S17) revealed a progressive decrease in the average contact potential difference (CPD), from 181.3 mV for the control to 134.7, 108.4, and 55.7 mV for the TMA‐, TFPA‐, and TBPAA‐modified films, respectively. The corresponding histogram of interfacial potential distribution (Figure 3m) indicated a more uniform surface potential in the treated films. These results suggest that aromatic aldehyde molecules with strongly electron‐donating central cores modulate the surface energy levels, thereby optimizing energy level alignment and charge transfer kinetics [32]. This interpretation is further supported by UPS measurements (Figures S18 and 3n), which reveal an increased work function and a concomitant shift in surface energy levels, leading to improved interfacial alignment with the hole transport layer (HTL). Collectively, these results underscore the critical role of the additives, particularly TBPAA, in simultaneously passivating defects and optimizing interfacial energy level alignment, thereby enabling efficient charge separation, suppressing non‐radiative recombination, and thereby offering the potential for enhanced photovoltaic performance [33].

To evaluate the passivation efficacy of the three aromatic aldehydes, perovskite solar cells (PSCs) with a structure of FTO/C‐TiO2/SnO2/perovskite/Spiro‐OMeTAD/Ag were fabricated (Figure 4a). A systematic concentration screening (0.05–0.5 mg mL−1) under identical conditions identified 0.1 mg mL−1 as the optimal dosage for all additives, as confirmed by statistical analysis (Figure S19), thereby ensuring a fair comparison of their intrinsic effects. Under these optimized conditions, the J–V characteristics measured under AM 1.5G illumination (Figures 4b and S20) reveal that the TBPAA‐based device delivers the highest performance, with a power conversion efficiency (PCE) of 26.12%, an open‐circuit voltage (V OC) of 1.188 V, a short‐circuit current density (J SC) of 25.63 mA cm−2, and a fill factor (FF) of 85.73%, outperforming the TFPA‐, TMA‐, and control devices. In addition to the improved efficiency, the TBPAA‐modified device exhibits minimal hysteresis (0.7%), markedly lower than that of the TFPA‐, TMA‐, and control devices (Table 1), indicating suppressed interfacial charge trapping and recombination losses. Consistently, under steady‐state maximum power point tracking, the TBPAA‐based device sustains a stabilized PCE of 25.77% over 300 s (Figure S21), further confirming its superior operational stability. To further validate the device performance, a mini module with an active area of 14.0 cm2 fabricated using TBPAA achieves a PCE of 22.41% (Figures 4c and S22; Table S3), demonstrating its scalability. Meanwhile, the Incident photon‐to‐electron conversion efficiency (IPCE) spectra (Figure 4d) yield an integrated current density of 25.03 mA cm−2, in good agreement with the J SC values obtained from J–V measurements, thereby confirming the reliability of the photocurrent output. To assess reproducibility, statistical analysis based on 20 independent devices (Figures S23 and S24; Tables S4 and S5) confirms the superior reliability and consistency of the TBPAA‐based PSCs and PSMs.

FIGURE 4.

FIGURE 4

(a) the structure illustration of PSCs. (b) Reverse J–V curves of the PSCs without and with TMA, TFPA, and TBPAA. (c) J–V curves of the perovskite solar modules using TBPAA as an additive. Inset: Photovoltaic parameters and image of the device. (d) IPCE spectra and corresponding integrated short‐circuit current density (J SC) of the PSCs. (e) Nyquist plots (inset: equivalent circuit) of different PSCs. (f) The light‐intensity dependence of V OC for PSCs.

TABLE 1.

Summary of device performance of perovskite solar cells without and with TMA, TFPA, and TBPAA.

Sample Scan mode V oc (V) J sc (mA cm−2) FF (%) PCE (%) Hysteresis index a
Control Reverse 1.155 25.38 80.61 23.62 0.018
Forward 1.142 25.29 78.85 22.78
with TMA Reverse 1.175 25.46 82.86 24.79 0.011
Forward 1.166 25.37 80.78 23.89
with TFPA Reverse 1.181 25.55 84.77 25.57 0.009
Forward 1.175 25.42 83.97 25.08
With TBPAA Reverse 1.188 25.63 85.73 26.12 0.007
Forward 1.184 25.51 84.98 25.66
a

Hysteresis index = (J RS(0.8V OC)‐J FS(0.8V OC))/J RS(0.8V OC).

The trap state density in perovskite films was quantitatively assessed using the space charge limited current (SCLC) method [34]. As shown in Figure S25, the pristine control film exhibits a trap state density of 2.87 × 1015 cm−3, which decreases progressively to 2.62 × 1015, 2.35 × 1015, and 1.82 × 1015 cm−3 upon treatment with TMA, TFPA, and TBPAA, respectively, directly confirming the superior defect passivation capability of TBPAA. Electrochemical impedance spectroscopy (EIS) was employed to elucidate the influence of the additives on charge transport and recombination dynamics within the perovskite devices (Figure 4e; Table S6). The high‐ and low‐frequency semicircles are assigned to the charge transfer resistance (R ct) and recombination resistance (R rec), respectively. Relative to the control device, the additive‐treated devices exhibit a reduced R ct, indicative of facilitated charge transport, which is attributed to improved film crystallinity and reduced trap density upon additive incorporation. Conversely, a pronounced increase in R rec is observed, suggesting suppressed charge recombination due to prolonged carrier lifetime and effective defect passivation [22]. Moreover, voltage‐dependent impedance analysis (Figure 4f) yields progressively decreasing ideality factors of 1.76, 1.58, 1.51, and 1.46 for the control, TMA‐, TFPA‐, and TBPAA‐treated devices, respectively, indicating a substantial mitigation of trap‐assisted Shockley–Read–Hall (SRH) recombination. Notably, the TBPAA‐based device exhibits the lowest ideality factor, underscoring its superior capability in reducing defect state density. Collectively, these results demonstrate that the additives, particularly TBPAA, effectively regulate charge transport and recombination dynamics, leading to enhanced device performance [35].

To clarify the role of aromatic aldehyde additives, their effects on the long‐term stability of PSCs were systematically investigated. The ambient stability of unencapsulated devices was evaluated in air at 30%–40% relative humidity (ISOS‐D‐1, Figure 5a). After 2100 h of aging, the control device retained only 48 % of its initial PCE, whereas devices incorporating TMA and TFPA maintained 74 % and 82 %, respectively. Notably, the TBPAA‐modified device exhibited the highest stability, preserving 92 % of its initial efficiency, indicating the superior passivation capability of TBPAA. To further evaluate device durability under operating conditions, the operational stability of unencapsulated PSCs was measured at the maximum power point (MPP) under continuous one‐sun illumination in a N2 atmosphere at 65 °C (ISOS‐L‐2, Figure 5b). After 1000 h, the control device retained 62 % of its initial PCE, while TMA‐, TFPA‐, and TBPAA‐based devices retained 75 %, 84 %, and 95 %, respectively. This trend is consistent with the ambient stability results, further confirming the effectiveness of aromatic aldehyde additives, particularly TBPAA, in enhancing device robustness. Under 85°C conditions (Figure S26), the TBPAA‐modified device maintained 93% of its initial efficiency after 400 h of continuous operation, demonstrating excellent operational stability. To elucidate the origin of the improved stability, XRD measurements were performed on films aged 2000 h under ambient conditions (30%–40% RH) (Figure S27). The control film showed pronounced degradation, as evidenced by the significant increase in diffraction peaks associated with PbI2 and δ‐FAPbI3 phases. In comparison, TMA‐ and TFPA‐treated films exhibited noticeably weaker signals corresponding to these decomposition products. Strikingly, the TBPAA‐treated film displayed only a faint PbI2 peak, indicating that TBPAA most effectively suppresses the formation of degradation phases and stabilizes the perovskite structure.

FIGURE 5.

FIGURE 5

(a) PCE evolution of the unencapsulated devices stored in dark and ambient environments (30%–40% RH) for 2000 h. Error bars represent the standard deviation. (b) MPPT of the unencapsulated devices under simulated illumination at 65°C in N2. (the test based on the device structure of FTO/C‐TiO2/SnO2/perovskite/PTAA/Au). (c–f) The temperature‐dependent conductivity of the perovskite films without and with TMA, TFPA, and TBPAA treatment.

The AFM measurements were further employed to elucidate the morphological evolution of the aged films (Figure S28). The control film exhibits a substantial increase in surface roughness, accompanied by the emergence of numerous small grains and pores, indicative of pronounced structural degradation. In contrast, films treated with aromatic carbonyl additives, particularly TBPAA, effectively suppress such aging‐induced deterioration, preserving a comparatively uniform and compact morphology.

Given the critical role of ion migration in determining device stability, the activation energy (Ea) for ion migration was evaluated via temperature‐dependent conductivity measurements [36]. As shown in Figure 5c–f, the control device exhibits an Ea of 0.62 eV, which increases to 0.67, 0.71, and 0.74 eV for devices incorporating TMA, TFPA, and TBPAA, respectively. This gradual increase suggests that aromatic aldehyde additives effectively suppress ion migration, thereby enhancing the stability of both the devices and the corresponding thin films, with TBPAA showing the most pronounced effect [37]. Consistent with the environmental aging results, these findings indicate that aromatic carbonyl additives with stronger electron‐donating central‐core groups are more effective in enhancing device stability and environmental durability.

3. Conclusion

In conclusion, we reveal that the electron‐donating strength of the central core critically determines the passivation effectiveness of aromatic carbonyl molecules, as illustrated by three designed molecules (TMA, TFPA, and TBPAA) with similar backbones but distinct central cores. It was found that increasing the electron‐donating ability of the molecular core enhances the electron density on the carbonyl groups, thereby improving the ability of these aromatic carbonyl additives to enhance perovskite film crystallinity and reduce defect density and strengthen film stability. Perovskite solar cells incorporating TBPAA, the molecule with the most electron‐rich core, achieved PCEs of 26.12% (0.09 cm2) and 22.41% (14.0 cm2). Meanwhile, unencapsulated TBPAA‐containing devices exhibited excellent stability, retaining 95% of their initial PCE at the MPP under continuous one‐sun illumination in a N2 atmosphere at 65 °C. These findings highlight the critical influence of the molecular central core on the defect‐passivation capability of aromatic carbonyl molecules and offer guiding principles for designing highly efficient and stable perovskite photovoltaics.

Conflicts of Interest

The authors declare no conflicts of interest.

Supporting information

Supporting File 1: anie73335‐sup‐0001‐Data1.xlsx.

Supporting File 2: anie73335‐sup‐0002‐Data2.txt.

Supporting File 3: anie73335‐sup‐0003‐Data3.txt.

Supporting File 4: anie73335‐sup‐0004‐SuppMat.docx.

Acknowledgments

This work was financially supported by the Strategic Priority Research Program of the Chinese Academy of Sciences (XDB1140000), the Natural Science Foundation of China (22209090, 52272255, U23A20141, 22578242,), the Taishan Industrial Leading Talents in Shandong Province (tscx202507052), and Shandong Province Higher Education Institutions Youth Innovation Team Development Program (2023KJC016).

Contributor Information

Shiwei Liu, Email: liushiweiqust@126.com.

Shuping Pang, Email: pangsp@qibebt.ac.cn.

Xin Guo, Email: guoxin@dicp.ac.cn.

Xiaoqing Jiang, Email: jiangxiaoqing8811@126.com.

Data Availability Statement

The data that support the findings of this study are available from the corresponding author upon reasonable request.

References

  • 1. Kojima A., Teshima K., Shirai Y., and Miyasaka T., “Organometal Halide Perovskites as Visible‐Light Sensitizers for Photovoltaic Cells,” Journal of the American Chemical Society 131 (2009): 6050–6051, 10.1021/ja809598r. [DOI] [PubMed] [Google Scholar]
  • 2. Dong Q., Fang Y., Shao Y., et al., “Electron‐Hole Diffusion Lengths >175 µm in Solution‐grown CH3NH3PbI3 Single Crystals,” Science 347 (2015): 967–970. [DOI] [PubMed] [Google Scholar]
  • 3. Eperon G. E., Hörantner M. T., and Snaith H. J., “Metal Halide Perovskite Tandem and Multiple‐Junction Photovoltaics,” Nature Reviews Chemistry 1 (2017): 0095, 10.1038/s41570-017-0095. [DOI] [Google Scholar]
  • 4. Bi D., Yi C., Luo J., et al., “Polymer‐Templated Nucleation and Crystal Growth of Perovskite Films for Solar Cells With Efficiency Greater Than 21%,” Nature Energy 1 (2016): 16142, 10.1038/nenergy.2016.142. [DOI] [Google Scholar]
  • 5. Zhao R., Wu T., Huang R., Wang Y., and Hua Y., “A Universal and Versatile Hole Transport Layer “Activator” Enables Stable Perovskite Solar Cells With Efficiency near 25%,” Advanced Functional Materials 34 (2024): 2314758, 10.1002/adfm.202314758. [DOI] [Google Scholar]
  • 6. Jeong J., Kim M., Seo J., et al., “Pseudo‐Halide Anion Engineering for α‐FAPbI3 Perovskite Solar Cells,” Nature 592 (2021): 381–385, 10.1038/s41586-021-03406-5. [DOI] [PubMed] [Google Scholar]
  • 7. Wu T., Wang P., Zheng L., Zhao Y., and Hua Y., “Perovskite Crystallization and Hot Carrier Dynamics Manipulation Enables Efficient and Stable Perovskite Solar Cells With 25.32% Efficiency,” Advanced Energy Materials 14 (2024): 2400078, 10.1002/aenm.202400078. [DOI] [Google Scholar]
  • 8. Aydin E., De Bastiani M., and De Wolf S., “Defect and Contact Passivation for Perovskite Solar Cells,” Advanced Materials 31 (2019): 1900428, 10.1002/adma.201900428. [DOI] [PubMed] [Google Scholar]
  • 9. Zhang Z., Qiao L., Meng K., Long R., Chen G., and Gao P., “Rationalization of Passivation Strategies Toward High‐Performance Perovskite Solar Cells,” Chemical Society Reviews 52 (2023): 163–195, 10.1039/D2CS00217E. [DOI] [PubMed] [Google Scholar]
  • 10. Guo F., Li M., Wang X., et al., “Carbonyl‐Amine Synergistic Dual‐Site Passivation for Efficient and Stable Wide‐Bandgap Perovskite Solar Cells,” Advanced Functional Materials 0 (2026): e00017, 10.1002/adfm.202600017. [DOI] [Google Scholar]
  • 11. Wang Q., Chen Y., Chen X., et al., “Tailored Succinic Acid‐Derived Molecular Structures Toward 25.41%‐Efficiency and Stable Perovskite Solar Cells,” Advanced Materials 36 (2024): 2307709, 10.1002/adma.202307709. [DOI] [PubMed] [Google Scholar]
  • 12. Lee D., Jeong D., Ahn T., and Park N., “Precursor Engineering for a Large‐Area Perovskite Solar Cell With >19% Efficiency,” ACS Energy Letters 4 (2019): 2393–2401. [Google Scholar]
  • 13. Han T.‐H., Lee J.‐W., Choi C., et al., “Perovskite‐polymer Composite Cross‐Linker Approach for Highly‐stable and Efficient Perovskite Solar Cells,” Nature Communications 10 (2019): 520, 10.1038/s41467-019-08455-z. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 14. Zhou Q., Gao Y., Cai C., et al., “Dually‐Passivated Perovskite Solar Cells With Reduced Voltage Loss and Increased Super Oxide Resistance,” Angewandte Chemie International Edition 60 (2021): 8303–8312, 10.1002/anie.202017148. [DOI] [PubMed] [Google Scholar]
  • 15. Yang L., Fang Z., Jin Y., et al., “Suppressing Halide Segregation via Pyridine‐Derivative Isomers Enables Efficient 1.68 eV Bandgap Perovskite Solar Cells,” Advanced Materials 36 (2024): 2311923, 10.1002/adma.202311923. [DOI] [PubMed] [Google Scholar]
  • 16. Yang S., Dai J., Yu Z., et al., “Tailoring Passivation Molecular Structures for Extremely Small Open‐Circuit Voltage Loss in Perovskite Solar Cells,” Journal of the American Chemical Society 141 (2019): 5781–5787, 10.1021/jacs.8b13091. [DOI] [PubMed] [Google Scholar]
  • 17. Wang K., Zhou T., Wang Z., et al., “Chiral Molecular Engineering for Synergistic Defect Passivation and Phase Stabilization Enables 22.19%‐Efficient Inorganic Perovskite Solar Cells,” Advanced Energy Materials 16 (2026): e06140, 10.1002/aenm.202506140. [DOI] [Google Scholar]
  • 18. Gu X., Xiang W., Tian Q., and Liu S., “Rational Surface‐Defect Control via Designed Passivation for High‐Efficiency Inorganic Perovskite Solar Cells,” Angewandte Chemie International Edition 60 (2021): 23164–23170, 10.1002/anie.202109724. [DOI] [PubMed] [Google Scholar]
  • 19. Zhang C., Jia Y., Zhang B., et al., “Machine Learning‐driven Interface Material Design for High‐performance Perovskite Solar Cells With Scalability and Band‐gap Universality,” Joule 10 (2026): 102264, 10.1016/j.joule.2025.102264. [DOI] [Google Scholar]
  • 20. Li C., Zhu Z., Wang Y., et al., “Lead Acetate Produced From Lead‐Acid Battery for Efficient Perovskite Solar Cells,” Nano Energy 69 (2020): 104380, 10.1016/j.nanoen.2019.104380. [DOI] [Google Scholar]
  • 21. Li Z., Wang K., Li R., et al., “Interfacial Energetics Reconstruction via Bridging Engineering for Efficient Inverted Perovskite Solar Cells and Modules,” Angewandte Chemie International Edition 65 (2026): e9286497. [DOI] [PubMed] [Google Scholar]
  • 22. Wang G., Wang W., Bai L., et al., “Grain Boundary Chemical Anchoring via Bidirectional Active Site Additive Enables Efficient and Stable Perovskite Solar Cells,” Advanced Materials Interfaces 9 (2022): 2200904, 10.1002/admi.202200904. [DOI] [Google Scholar]
  • 23. Jiang X., Zhu L., Zhang B., et al., “Insights into the Role of π‐Electrons of Aromatic Aldehydes in Passivating Perovskite Defects,” Angewandte Chemie International Edition 64 (2024): e202420369, 10.1002/anie.202420369. [DOI] [PubMed] [Google Scholar]
  • 24. Guan S., Wang K., Niu T., et al., “Stabilizing Intrinsic Phase of Phase‐Pure FAPbI3 by Organic Molten‐Salt Molecular Bridges,” Angewandte Chemie International Edition 65 (2026): e24560. [DOI] [PubMed] [Google Scholar]
  • 25. Xu D., Cao H., Fan Z., et al., “A Triphenylamine‐Functionalized Co‐Assembly Material for Record Efficiency Inverted CsPbI3 Perovskite Solar Cells,” Angewandte Chemie International Edition 64 (2025): e202502221, 10.1002/anie.202502221. [DOI] [PubMed] [Google Scholar]
  • 26. Aranda C. A., Alvarez A. O., Chivrony V. S., Das C., Rai M., and Saliba M., “Overcoming Ionic Migration in Perovskite Solar Cells Through Alkali Metals,” Joule 8 (2024): 241–254, 10.1016/j.joule.2023.11.011. [DOI] [Google Scholar]
  • 27. Song T.‐B., Yuan Z., Mori M., et al., “Revealing the Dynamics of Hybrid Metal Halide Perovskite Formation via Multimodal in Situ Probes,” Advanced Functional Materials 30 (2020): 1908337, 10.1002/adfm.201908337. [DOI] [Google Scholar]
  • 28. Ummadisingu A., Steier L., Seo J., et al., “The Effect of Illumination on the Formation of Metal Halide Perovskite Films,” Nature 545 (2017): 208–212, 10.1038/nature22072. [DOI] [PubMed] [Google Scholar]
  • 29. Zhao R., Wang P., Wang L., et al., “In Situ Combined‐Hole Transport Layer for Highly Efficient Perovskite Solar Cells,” Advanced Functional Materials 34 (2024): 2307559, 10.1002/adfm.202307559. [DOI] [Google Scholar]
  • 30. Yuan Y., Yan G., Dreessen C., and Kirchartz T., “Understanding Power‐Law Photoluminescence Decays and Bimolecular Recombination in Lead‐Halide Perovskites,” Advanced Energy Materials 15 (2025): 2403279, 10.1002/aenm.202403279. [DOI] [Google Scholar]
  • 31. Si H., Zhang S., Ma S., et al., “Emerging Conductive Atomic Force Microscopy for Metal Halide Perovskite Materials and Solar Cells,” Advanced Energy Materials 10 (2020): 1903922, 10.1002/aenm.201903922. [DOI] [Google Scholar]
  • 32. Hou Y., Aydin E., De Bastiani M., et al., “Efficient Tandem Solar Cells With Solution‐processed Perovskite on Textured Crystalline Silicon,” Science 367 (2020): 1135–1140, 10.1126/science.aaz3691. [DOI] [PubMed] [Google Scholar]
  • 33. Xie L., Zhao X., Wang J., et al., “Multifunctional Anchoring of O‐Ligands for High‐Performance and Stable Inverted Perovskite Solar Cells,” InfoMat 5 (2023): e12379, 10.1002/inf2.12379. [DOI] [Google Scholar]
  • 34. Yoo J. J., Seo G., Chua M. R., et al., “Efficient Perovskite Solar Cells via Improved Carrier Management,” Nature 590 (2021): 587–593, 10.1038/s41586-021-03285-w. [DOI] [PubMed] [Google Scholar]
  • 35. Yang G., Yin Y., Dong K., et al., “Realizing Uniform Defect Passivation via Self‐Polymerization of Benzenesulfonate Molecules in Perovskite Photovoltaics,” Advanced Materials 37 (2025): 2503435, 10.1002/adma.202503435. [DOI] [PubMed] [Google Scholar]
  • 36. Zhao J., Deng Y., Wei H., et al., “Strained Hybrid Perovskite Thin Films and Their Impact on the Intrinsic Stability of Perovskite Solar Cells,” Science Advances 3 (2017): eaao5616, 10.1126/sciadv.aao5616. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 37. Zhong Y., Yang J., Wang X., et al., “Inhibition of Ion Migration for Highly Efficient and Stable Perovskite Solar Cells,” Advanced Materials 35 (2023): 2302552, 10.1002/adma.202302552. [DOI] [PubMed] [Google Scholar]

Associated Data

This section collects any data citations, data availability statements, or supplementary materials included in this article.

Supplementary Materials

Supporting File 1: anie73335‐sup‐0001‐Data1.xlsx.

Supporting File 2: anie73335‐sup‐0002‐Data2.txt.

Supporting File 3: anie73335‐sup‐0003‐Data3.txt.

Supporting File 4: anie73335‐sup‐0004‐SuppMat.docx.

Data Availability Statement

The data that support the findings of this study are available from the corresponding author upon reasonable request.


Articles from Angewandte Chemie (International Ed. in English) are provided here courtesy of Wiley

RESOURCES