Abstract
The extraction of berberine was carried out from Berberis vulgaris, Berberis aquifolium, and Hydrastis canadensis plants using ethanol and water (70:30, v/v). The extracted berberine was characterized by ultraviolet‐visible and Fourier‐transform infrared spectroscopy. The purity of berberine was ascertained by thin‐layer chromatography using n‐propanol‐formic acid‐water (95:1:4) and (90:1:9) solvents. hRf values were in the range of 44–49 with compact spots (diameter 0.2–0.4 cm). HPLC was carried out using ammonium acetate buffer and acetonitrile in gradient mode with Zodiac (4.6 × 150 mm, 3 μm) column. The flow rate was 1.0 mL/min and detection was at 220 nm. The values of separation and resolution factors of the standard and the extracted berberine were in the range of 1.13–1.16 and 1.40–1.71, respectively. A comparison has shown that both thin‐layer chromatography and high‐performance liquid chromatography (HPLC) methods found applications in different situations and requirements. The extracted berberine samples were used to treat Leishmaniosis and the results showed better activity of berberine in comparison to the standard drug Amphotericin B. Briefly, the reported research is a novel and may be used to extract berberine from plants, separation and identification of berberine by thin layer chromatography and HPLC and to treat Leishmaniosis.
Keywords: berberine, extraction, high‐performance liquid chromatography, leishmaniosis, thin layer chromatography
1. INTRODUCTION
Berberine is an active phyto‐constituent of Berberis vulgaris (Barbery), Berberis aquifolium (Oregon grape), Berberis aristata (Tree Turmeric), and Hydrastis canadensis (Goldenseal) plant with a variety of medicinal activities against various diseases in humans. Basically, berberine (Figure 1) is an alkaloid yellowish and found in the root, rhizome, and stem bark of above mentioned medicinal plants [1]. It is also an active marker of Berberis vulgaris, Berberis aquifolium, and Hydrastis canadensis. Since ancient times, berberine has been used as a Chinese medicine due to its pharmacological and clinical effects to cure various types of illnesses. Berberis vulgaris and Berberis aquifolium both herbs belong to the Berberidaceae family. The common names of Berberis vulgaris in different languages are Kashmal (Hindi); Pepperidge bush (English); Epine‐Vinette (French) and Berberitzen (Germany). Generally, this plant is found in Europe, India, and the North of Asia. The bark and root were used for the extraction of berberine. Similarly, the common names of Berberis aquifolium in different languages are Vinettie (French), Rocky Mountain Grape (English), and Gemeiner Sauardorn (German). The distribution of the plants is in the western United States; especially abundant in the northern part of the Pacific coast. The root was used for the extraction of berberine. The third plant selected for this study was Hydrastis canadensis, which belongs to the family Ranunculaceae and is also known as Sceaud in French, Eye Balm in English, and Golden Seal in German. Mostly, this plant is found in Canada and the United States. The rhizome was used for the extraction of berberine [2]. A thorough search of the literature dictates that berberine has a wide range of biological activities like anti‐malarial, anti‐hypertensive, anti‐arrhythmic, anti‐hyperglycemic, anti‐tumor, anti‐inflammatory, anti‐fungal, anti‐oxidative, and cerebro‐protective activities [3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15]. Specifically, Berberis vulgaris and Berberis aquifolium are used for treating hyperlipidemia, bacterial and viral infections, Alzheimer's disease, osteoporosis, tumors, diabetes, cardiovascular problems, mental disease, and so forth. [3]. Cecil et al. [16] studied that berberine was shown to inhibit the growth of influenza A. The exact mechanism is not known so far, but it is assumed that berberine prevents virus proteins from unfolding. In another study, Junio et al. [17] found that berberine inhibits the growth of Staphylococcus Aureus.
FIGURE 1.

Chemical structure of berberine chloride.
High‐performance liquid chromatography (HPLC) is an important technique for the separation and identification of several molecules [18, 19, 20]. There are only a few papers available in the literature on the separation and identification of berberine. Lu et al. [21] determined berberine contents in “Stomacheasy”; a Chinese medicine by thin‐layer chromatography (TLC). The authors used imidazole ionic liquid in this study. Li et al. [22] prepared and used rosin‐based polymer microspheres for the separation of berberine from Coptidis rhizome extract. The authors used chromatographic column breakthrough experiments and reported an increase in the alkaloid contents; including berberine; from 34.2% to 91.0%. Chaudhary et al. [23] carried out quantitation of berberine by HPTLC in the Thalictrum foliolosum plant. Silica gel 60 GF254 (10 × 10 cm) plates were used with n‐PrOH‐H2O‐HCOOH (90:10:1) as the mobile phase. The Rf value of berberine was 0.44. Pasrija et al. [24] used HPLC for the separation of berberine with a C18 column and with a gradient mobile phase made of acetonitrile and potassium dihydrogen phosphate buffer of pH 2.5. The flow rate was 1.0 mL/min with 346 nm detection. Srinivasan et al. [25] described HPLC and TLC evaluation of berberine in Tinospora cordifolia and Tinospora sinensis plants. Also, Li et al. [26] evaluated HPLC analysis of berberine in the roots of five species of berberine plants. The authors reported good amounts of berberine in various plants. A critical evaluation of these papers was carried out and observed that these methods used a large time and costly chemicals. Besides, the detection limits are not good.
Therefore, there is a great demand to develop more advanced methods for the extraction, separation, and identification of such important alkaloids present in various plants because sample preparation and extraction aspects are important [27, 28, 29, 30, 31]. In view of these facts, efforts are made to develop fast, reliable, and economical extraction, TLC, and HPLC methods for the separation and identification of berberine from the extracts of Berberis vulgaris, Berberis aquifolium, and Hydrastis canadensis plants. To make this article useful efforts are made to evaluate the biological activities of Berberine against Leishmaniasis.
2. MATERIALS AND METHODS
2.1. Experimental section
2.1.1. Chemicals and reagents
Methanol, n‐propanol, and acetonitrile of HPLC grade were purchased from Merck. Formic acid was procured from Qualigens, India. TLC Silica gel 60 F254 plates were purchased from Merck. Standard berberine chloride was purchased from Sigma‐Aldrich. Ammonium acetate from Sigma‐Aldrich. The dragendorff reagent was supplied by Sarkhej. Dragendorff is a color reagent and is typically used for detecting alkaloids separated by planar chromatography.
2.1.2. Instrumentation
Waters HPLC (Empower 3) Aliance‐2696 was used for qualitative analysis of berberine. A double‐beam UV spectrophotometer (Shimadzu UV 1800) was used for measuring UV absorbance. The column used was ZODIAC C18 (4.6 × 150 mm, 3 μm). This column reduced hydrophobicity to attain perfect hydrophobic selectivity with resolution. This column is a good choice for the separation of basic acidic, and neutral molecules. Analytical weighing balance (Mettler Toledo) and ultrasonicator of Remi were used for weighing and sonicating the sample solution as well. CAMAG Twin Trough Chamber was used for TLC. Fourier‐transform infrared spectroscopy (FT‐IR) of Agilent technologies was used to record the spectra.
2.2. Methodology
2.2.1. Extraction of berberine from plants
About 10 g dried samples of the Berberis Vulgaris (bark of the root), Berberis aquifolium (root), and Hydrastis canadensis (rhizome) plants were crushed in a grinder mixture separately. These samples were refluxed for 3 h in 50 mL with a mixture of ethanol and water (70:30, v/v). The extract was cooled and filtered through Whatman filter paper no.1. The filtrate was then concentrated up to 5 mL in a water bath and collected in a vial separately, and respectively. These prepared samples were used for TLC, HPLC, and biological studies.
2.2.2. Sample preparation for chromatography
The sample preparation for chromatographic studies is a very essential part. For this study, the standard berberine (1.0 mg/mL) was prepared in methanol. The plant‐extracted samples were also prepared in methanol of the same concentrations. All the samples were filtered via a 0.45 μm membrane. These prepared solutions of the samples and standards were further used for TLC, HPLC, and biological studies.
2.2.3. Thin‐layer chromatography
Note that, 5.0 μL of each sample and a standard of berberine were applied on a TLC plate and run in a prior saturated TLC chamber (10 × 10 × 2 cm). The mobile phases used were n‐propanol‐formic acid‐water in 90:1:9 (I) and 95:1:4 [II, (v/v)] ratios. The plates in mobile phase I were treated with dragendorff reagent and observed under UV light at 366 nm. The solvent front was 7.6 cm. TLC plates were developed for 10 min for both mobile phases. The plates were taken out and dried in an oven at 100°C. The plates in mobile phase I were observed in daylight, under UV light at 254 and 366 nm, respectively. The plates in mobile phase II were observed under daylight, UV light at 254 nm, and visible light at 366 nm. The solvent front, distance traveled and spot diameters were calculated. hRf values were calculated as per the standard method.
2.2.4. High‐performance LC
The separation and identification of berberine in HPLC was carried out in a gradient mode. The volume of the sample injected was 5.0 μL. The mobile phase conditions are given in Table 1. The different combinations of 5.0 mM ammonium acetate and acetonitrile in gradient mode were used. The detection was achieved by a photodiode array detector at 220 nm. The column temperature was 27°C throughout the experiments.
TABLE 1.
Gradient mobile phase for high‐performance liquid chromatography (HPLC).
| Time (min) | Ammonium acetate buffer (%) | Acetonitrile (%) | Flow rates (mL/min) |
|---|---|---|---|
| 0.00 | 90 | 10 | 1.0 |
| 2.00 | 90 | 10 | 1.0 |
| 10.00 | 5 | 95 | 1.0 |
| 13.00 | 5 | 95 | 1.0 |
| 13.10 | 10 | 10 | 1.0 |
| 15.00 | 10 | 10 | 1.0 |
2.2.5. Biological assay
The anti‐leishmanial activity of extracted berberine samples was carried out using Leishmania donovani promastigotes stage cells. In vitro, the anti‐leishmanial activity of berberine was evaluated by cultivating L. donovani Promastigote of mid‐Log phase in 96 well plates for 72 h at 26°C. Prior to treatment, 2 × 106 /mL cells were seeded in each well in triplicate for each concentration. Amphotericin B was used as a control drug (0–100 μm). The concentrations of berberine used were 0–100 μm. MTT assay was performed and absorbance was recorded at 560 nm. A plot was constructed between the percentage of cells dead and log concentrations (μm). The IC50 values were evaluated as per the standard procedure.
3. RESULTS AND DISCUSSIONS
The results and discussion of this article are divided into four sections, that is, characterization of extracted berberine, separation and identification by TLC, HPLC, and biological evaluation against Leishmaniosis. These sections are discussed below.
3.1. Characterization
The max. plot for berberine standard, Berberis vulgaris, Berberis aquifolium, and Hydrastis canadensis were recorded at 428, 349, 265, and 230 nm. These are given in Figure 2. It is clear from this Figure that the spectra of the extracted berberine matched with the standard berberine; confirming the authenticity of the extracted samples. The standard and extracted berberine samples from Berberis vulgaris, Berberis aquifolium, and Hydrastis canadensis were also run on an FT‐IR machine, and the spectra were recorded. First, a standard berberine chloride sample was run followed by Berberis vulgaris, Berberis aquifolium, and Hydrastis canadensis samples. The standard berberine chloride showed a spectrum at 2846, 1633, 1566, and 1502 cm‐1. The peaks at 2846, 1633, 1566, and 1502 cm‐1 were also observed in the plant samples in a similar fashion [32]. All these studies clearly confirmed the extracted compounds as berberine.
FIGURE 2.

The max plot for berberine standard and extracted berberine.
3.2. Thin‐layer chromatography
The separation and identification of berberine in plant extracts in propanol‐formic acid‐water in 90:1:9 (I) and 95:1:4 [II, (v/v)] ratios are given in Figure 3. The developed chromatogram in mobile phase I is shown in Figure 3. The plate (a) was developed with n‐propanol‐formic acid‐water (95:1:4, v/v) and detected by UV light at 366 nm. The plate (b) was developed with n‐propanol‐formic acid‐water (90:1:9, v/v); detection by dragendorff reagent. The hRf values obtained from plate (a) for the standard berberine was 44 while the hRf values of berberine extracted from Berberis vulgaris, Berberis aquifolium, and Hydrastis canadensis were 44, 44, and 46, respectively (Table 2). The hRf values obtained from plate (b) for the standard berberine was 49 while the hRf values of berberine extracted from Berberis vulgaris, Berberis aquifolium, and Hydrastis canadensis were 48, 49, and 49, respectively (Table 2). From these data it is clear that the hRf values of the standard berberine and extracted berberine were very close; confirming the purity of the berberine. It is clear that the spots showed tailing in mobile phase n‐propanol‐formic acid‐water (95:1:4, v/v) while the spots were compact in mobile phase n‐propanol‐formic acid‐water (90:1:9, v/v). The spot diameters on the TLC plate developed by n‐propanol‐formic acid‐water (90:1:9, v/v) were in the range of 0.2–0.4 cm. This observation confirmed the later mobile phase as the best one. TLC experiments were also optimized. The optimization was carried out by using a variety of mobile phases, run time, mode of detection, amount of injected, and temperature. As a result of many experiments, the best TLC conditions are described in this section. The developed method for the determination of berberine in Berberis vulgaris, Berberis aquifolium, and Hydrastis canadensis plants is fast, accurate, and reproducible.
FIGURE 3.

Spots of Berberis vulgaris (BV), Berberis aquifolium (BA), Hydrastis canadensis (HC), and Berberine standard (B) (A): with n‐propanol‐formic acid‐water (95:1:4, v/v) and detection by ultraviolet (UV) light at 366 nm and (B): with n‐propanol‐formic acid‐water (90:1:9, v/v); detection by dragendorff reagent.
TABLE 2.
hRf values of berberine in different plants using two mobile phases.
| Berberine samples | hRf | Spot width (cm) |
|---|---|---|
| Mobile phase: n‐propanol‐formic acid‐water (90:1:9, v/v) | ||
| ▓Berberis vulgaris (BV) | 44 | 0.20 |
| ▓Hydrastis canadensis (HC) | 44 | 0.20 |
| ▓Berberis aquifolium (BA) | 46 | 0.20 |
| ▓Berberine standard (B) | 44 | 0.40 |
| Mobile phase: n‐propanol‐formic acid‐water (95:1:4, v/v) | ||
| ▓Berberis vulgaris (BV) | 49 | 0.25T |
| ▓Hydrastis canadensis (HC) | 48 | 0.30T |
| ▓Berberis aquifolium (BA) | 49 | 0.20T |
| ▓Berberine standard (B) | 49 | 0.25T |
T: Tailing.
3.3. High‐performance LC
The standard and the extracted samples of berberine were run in HPLC under the conditions described in the experimental section. The retention time of the standard berberine was 8.40 min with a small impurity appearing at 7.64 min. The extracted samples were also run under identical conditions and the retention times were 8.59, 8.66, and 8.75 min for berberine extracted from Berberis vulgaris, Berberis aquifolium, and Hydrastis canadensis. The chromatograms are shown in Figure 4. HPLC separation data were calculated and given in Table 3. The values of separation and resolution factors were greater than 1.0; indicating an excellent separation. Besides, the values of separation and resolution factors of the extracted berberine were close to the standard sample confirming the purity and identity of the extracted samples of the berberine. The purity was checked and found to be 98.49% with 1.51% of impurity. The purities were recorded at 77.32%, 79.06%, and 52.16% for Berberis vulgaris, Berberis aquifolium, and Hydrastis canadensis. The retention time of small impurities was also determined at 7.76, 7.74, and 7.79 with purities of 1.16%, 1.13%, and 0.66% for Berberis vulgaris, Berberis aquifolium, and Hydrastis canadensis. The number of theoretical plates and tailing factors were also calculated and given in Table 4. A perusal of this Table indicates that the values of theoretical plates were in the range from 5893 to 6350; indicating good column performance. The tailing factor for the standard berberine was 1.12 while the tailing factor of the extracted berberine was 1.23–1.34. These values were comparable with the value of the standard berberine.
FIGURE 4.

HPLC chromatograms of the standard and plant‐extracted berberine.
TABLE 3.
Separation data of the standard and extracted berberine.
| Berberine samples | tr (min) | k1 | k2 | α | Rs |
|---|---|---|---|---|---|
| Standard berberine | 8.40 | 3.36 | 3.80 | 1.13 | 1.40 |
| Berberis vulgaris | 8.59 | 3.43 | 3.94 | 1.15 | 1.66 |
| Berberis aquifolium | 8.66 | 3.42 | 3.90 | 1.14 | 1.57 |
| Hydrastis Canadensis | 8.75 | 3.45 | 4.00 | 1.16 | 1.77 |
tr: Retention time; k1 and k2: retention factors, k: Separation factor, and RS: Resolution factor.
TABLE 4.
Theoretical plate and tailing factors of the high‐performance liquid chromatography (HPLC) separation berberine.
| Berberine samples | Number of theoretical plates | Tailing factors |
|---|---|---|
| Standard berberine | 6350 | 1.12 |
| Berberis vulgaris | 6098 | 1.23 |
| Berberis aquifolium | 5947 | 1.28 |
| Hydrastis Canadensis | 5893 | 1.34 |
3.3.1. Validation of the method
The reported developed HPLC method was validated concerning the following chromatographic aspects: linearity, the limit of detection (LOD), the limit of quantitation (LOQ), precision, accuracy, selectivity, robustness, and ruggedness.
Linearity
The linearity of calibration curves (peak area vs. concentration) for the berberine standard was calculated over the concentration ranges of 0.10–0.80 mg/mL. The calibration graph plotted was linear over these concentration ranges (n = 5). The linear regression analysis was determined on the resultant curves. The correlation coefficient (R2) (n = 5) was found to be 0.998 for the standard berberine. The values of relative standard deviation (RSD) for berberine, and berberine extracts from Berberis vulgaris, Berberis aquifolium, and Hydrastis canadensis were 1.56 1.88, 1.92, and 1.96, respectively.
LOD and LOQ
The LOD and limit of quantitation LOQ for berberine standard and extracted berberine from Berberis vulgaris, Berberis aquifolium, and Hydrastis canadensis were 1.0 and 1.5 μg/mL, respectively. The RSD values were 1.56%, 1.88%, 1.92%, and 1.96% for the standard and extracted berberine from Berberis vulgaris, Berberis aquifolium, and Hydrastis canadensis.
Specificity
The method is a fine specific which is clear from Figure 4. The retention times of the standard berberine, Berberis vulgaris, Berberis aquifolium, and Hydrastis canadensis were nearly similar. The calculated results proved a good specificity of the reported HPLC method.
Precision
The precision value was tested by applying three concentrations (0.01, 0.05, and 0.10 mg/mL) of the standard and extracted berberine from Berberis vulgaris, Berberis aquifolium, and Hydrastis canadensis. Further, five replicate runs were performed for the aforementioned concentrations. RSD values were in the range of 2.00 to 2.70%; showing the HPLC method precisely.
Accuracy
The different samples of the standard and extracted berberine from Berberis vulgaris, Berberis aquifolium, and Hydrastis canadensis were optimized to check the authenticity for accuracy method as given in the experimental section. The accuracy was achieved by injecting five replicates (n = 5) of peak areas of three different accuracy standards. The percent errors were calculated and found in the range of 1.1%–1.56%. These findings indicated a good accuracy of the developed method.
Robustness and ruggedness
The small changes made were performed such as in mobile phase compositions, flow rates, amounts loaded, and detection wavelengths. It was observed that there was no prominent variation in HPLC results; confirming the developed method as robust. The ruggedness was also performed during the development of the HPLC method. RSD values for intra‐ and inter‐days assays were in the range of 2.00 and 2.51; showing the robustness of the method. In addition, the results achieved with different operators were unaffected, which also indicated the ruggedness of the method.
3.4. Comparison of TLC and HPLC
It is very difficult to compare the results of TLC and HPLC because both techniques have their pros and cons. However, the comparison was made involving the cost of instrumentation and the chemicals used. Of course, the HPLC instrument is too much costly in comparison to TLC. Regarding the chemicals used both TLC and HPLC involve almost the same costs of chemicals in this experiment. However, the running time was high in TLC which took at least 60 min to identify the spots but in the case of HPLC the peaks appeared within 10 min. In this way, HPLC is better than TLC. But being this paper of research it needs to cover the whole community of the world. Consequently, TLC is very inexpensive and can be used in any part of the world including under‐developed countries. Briefly, both the reported methods have their advantages and disadvantages and the researchers can use the reported methods at their convenience and with the facilities available.
3.5. Biological activity of berberine against Leishmaniosis
As discussed in the experimental section, the activity of the extracted samples of berberine was carried out using L. donovani promastigotes stage cells. Amphotericin B was used as the standard drug. The results were analyzed in terms of the percentage of cells that died (Figure 5). This Figure clearly shows that the percentage of L. donovani promastigotes stage cells decreased by increasing the log concentration of berberine. The IC50 values were calculated from this graph. These values of berberine and the standard drug were 0.77 and 1.06, respectively. These data confirmed that berberine is the most active in comparison to the standard drug. The morphological status of the Leishmanial parasite in control and various concentrations of berberine are shown in Figure 6. A perusal of this Figure dictates that the parasite is normal under control conditions while the parasite was found to die in berberine‐treated cases. The death of the parasite was in the order of 12.5 < 25 < 50 < 100 μm. At 100 μm concentration. The parasite was found to be completely dead at 100 μm concentration; confirming an excellent activity of berberine.
FIGURE 5.

Anti‐leishmanial activity graph for IC50 value calculation.
FIGURE 6.

Morphological status of Leishmanial parasite (A): control, (B): dimethyl sulfoxide (DMSO) treated, and (C–F) at 100, 50, 25, and 12.5 μm, respectively.
The reported method was compared with other papers reported and it was found that this method is fast, efficient, and reproducible. Besides, the detection limits are quite good enough to be accepted for future research. Consequently, this method of berberine from Berberis vulgaris, Berberis aquifolium, and Hydrastis canadensis is effective and can be used on an industrial scale. The described TLC and HPLC methods may be used to identify the berberine and test the purity of the extracted samples. The biological study is an assent as berberine is much more effective in treating Leishmaniasis in comparison to the standard drug Amphotericin B. Briefly, the reported research work may be used as a reference to other researchers in the area of extraction, separation, and identification and treating Leishmaniasis. The most important application of this work is that it can be used anywhere in the world including under‐developed countries because of involving very inexpensive study of TLC.
4. CONCLUSION
The extracted berberine quantity from Berberis vulgaris, Berberis aquifolium, and Hydrastis canadensis plants ranged from 25.10 to 27.63% from the different plants. The characterization data obtained by using UV‐Visb and FT‐IR spectroscopy of the extracted berberine matched with those of the standard; confirming the identity of extracted berberine. TLC and LC were found to be suitable techniques for determining the purity of the berberine sample. The extracted samples were pure except that they had small impurities which appeared both in TLC and HPLC. The extracted samples showed excellent activity against L. donovani and found as a highly effective anti‐leishmanial agent. The IC50 values of the extracted berberine and the standard drug Amphotericin B were 0.77 and 1.06; confirming excellent activity of berberine. Briefly, the extraction method of berberine is very effective as it gives good percentage yields. Besides, the developed TLC and HPLC methods are fast, reproducible, and efficient. In addition to this, the anti‐leishmanial activity of berberine was found to be excellent. Briefly, the reported research may be used effectively to extract berberine from different plants and the berberine may be separated and identified by TLC and HPLC. Additionally, the anti‐leishmanial activity of berberine is an asset to society to treat Leishmaniosis.
CONFLICT OF INTEREST STATEMENT
The authors declare no conflict of interest.
FUNDING INFORMATION
Not applicable.
ACKNOWLEDGMENTS
The author (Zeid A. ALOthman) is grateful to the Researchers Supporting Project No. (RSP2023R1), King Saud University, Riyadh, Saudi Arabia.
Contributor Information
Syed Dilshad Alam, Email: dilshad826@gmail.com.
Imran Ali, Email: drimran.chiral@gmail.com.
DATA AVAILABILITY STATEMENT
All data are given in the manuscript. Data sharing is not applicable to this article as no datasets were generated or analyzed during the current study.
REFERENCES
- 1. Battu SK, Repka MA, Maddineni S, Chittiboyina AG, Avery MA, Majumdar S. Physicochemical characterization of berberine chloride: a perspective in the development of a solution dosage form for oral delivery. Am Assoc Pharm Sci. 2010;11:1466–1475. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 2. Och A, Podgórski R, Nowak R. Biological activity of berberine – a summary update. Toxins 2020;12:713. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 3. Tillhon M, Ortiz LMG, Lombardi P, Scovassi A. Berberine: New perspectives for old remedies. Biochem Pharmacol. 2012;84:1260–1267. [DOI] [PubMed] [Google Scholar]
- 4. Kumar A, Ekavali, Chopra K, Mukherjee M, Pottabathini R, Dhull DK. Current knowledge and pharmacological profile of berberine: an update. Eur J Pharmacol. 2015;761:288–297. [DOI] [PubMed] [Google Scholar]
- 5. Habtemariam S. Berberine and inflammatory bowel disease: a concise review. Pharmacol Res. 2016;113:592–599. [DOI] [PubMed] [Google Scholar]
- 6. Chang W. Non‐coding RNAs and Berberine: a new mechanism of its anti‐diabetic activities. Eur J Pharmacol. 2017;795:8–12. [DOI] [PubMed] [Google Scholar]
- 7. Wong SK, Chin K‐Y, Ima‐Nirwana S. Berberine and musculoskeletal disorders: the therapeutic potential and underlying molecular mechanisms. Phytomedicine 2020;73:152892. [DOI] [PubMed] [Google Scholar]
- 8. Majidzadeh H, Araj‐Khodaei M, Ghaffari M, Torbati M, Dolatabadi JEN, Hamblin MR. Nano‐based delivery systems for berberine: a modern anti‐cancer herbal medicine. Colloids Surf B Biointerfaces. 2020;194:111188. [DOI] [PubMed] [Google Scholar]
- 9. Tew XN, Lau NJX, Chellappan DK, Madheswaran T, Zeeshan F, Tambuwala MM, et al. Immunological axis of berberine in managing inflammation underlying chronic respiratory inflammatory diseases. Chem Biol Interact. 2020;317:108947. [DOI] [PubMed] [Google Scholar]
- 10. Zhang S‐w, Zhou J, Gober H‐J, Leung WT, Wang L. Effect and mechanism of berberine against polycystic ovary syndrome. Biomed Pharmacother. 2021;138:111468. [DOI] [PubMed] [Google Scholar]
- 11. Suadoni MT, Atherton I. Berberine for the treatment of hypertension: a systematic review. Complement Ther Clin Pract. 2021;42:10128. [DOI] [PubMed] [Google Scholar]
- 12. Zhou M, Deng Y, Liu M, Liao L, Dai X, Guo C, et al. The pharmacological activity of berberine, a review for liver protection. Eur J Pharmacol. 2021;890:173655. [DOI] [PubMed] [Google Scholar]
- 13. Zochedh A, Chandran K, Priya M, Sultan AB, Kathiresan T. DFT simulation of berberine chloride with spectroscopic characterization‐biological activity and molecular docking against breast cancer. Polycycl Arom Compd. Published online: May 8, 2023. [Google Scholar]
- 14. Lu H, Yan Z, Sun M. Studies on synthesis, physicochemical properties, biological activities of two novel berberine‐based salts with DL‐mandelate and cinnamate anions. J Mol Struct. 2023;1294:136359. [Google Scholar]
- 15. Bakshi J, Grewal S, Dhingra D, Kumari S. Improving the biological properties of berberine by using gellan and gum acacia as a potential delivery carrier. Carbohydr Polym Technol Applications. 2023;6:100347. [Google Scholar]
- 16. Cecil CE, Davis JM, Cech NB, Laster SM. Inhibition of H1N1 influenza A virus growth and induction of inflammatory mediators by the isoquinoline alkaloid berberine and extracts of goldenseal (Hydrastis canadensis). Int Immunopharmacol. 2011;11:1706–1714. [DOI] [PubMed] [Google Scholar]
- 17. Junio HA, Sy‐Cordero AA, Ettefagh KA, Burns JT, Micko KT, Graf TN, et al. Synergy‐directed fractionation of botanical medicines: a case study with goldenseal (Hydrastis canadensis). J Nat Prod. 2011;74:1621–1629. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 18. Aboul‐Enein HY, Ali I. A comparison of chiral resolution of econazole, miconazole and sulconazole by HPLC using normal phase amylose CSPs. Fres J Anal Chem. 2001;370:951–955. [DOI] [PubMed] [Google Scholar]
- 19. Aboul‐Enein HY, Ali I. HPLC Enantiomeric resolution of nebivolol on normal and reversed amylose based chiral phases. D Pharm. 2001;56:214–216. [PubMed] [Google Scholar]
- 20. Ali I, AL‐Othman ZA, Nagae N, Gaitonde VD, Dutta KK. Recent trends in ultrafast HPLC: new generation of superficially porous silica columns. J Sep Sci. 2013;35:3235–3249. [DOI] [PubMed] [Google Scholar]
- 21. Lu J, Ma H, Zhang W, Ma Z, Yao S. Separation of berberine hydrochloride and tetrahydropalmatine and their quantitative analysis with thin layer chromatography involved with ionic liquids. J Anal Method Chem. 2015;2015:642401. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 22. Li P, Qin L, Wang T, Dai L, Li H, Jiang J, et al. Preparation and adsorption characteristics of rosin‐based polymer microspheres for berberine hydrochloride and separation of total alkaloids from coptidis rhizome. Chem Eng J. 2020;392:123707. [Google Scholar]
- 23. Chaudhary MK, Misra A, Tripathi D, Srivastava S. In‐vitro anti‐urolithiatic activity and simultaneous HPTLC quantification of berberine and palmatine in standardized extract of Thalictrum foliolosum DC. South African J Bot. 2022;151:445–453. [Google Scholar]
- 24. Pasrija A, Singh R, Katiyar CK. Validated HPLC‐UV method for the determination of berberine in raw herb Daruharidra (Berberis aristata DC), its extract, and in commercially marketed Ayurvedic dosage forms. Int J Ayurved Res. 2010;1:243–246. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 25. Srinivasan GV, Unnikrishnan KP, Shree ABR, Balachandran I. HPLC estimation of berberine in Tinospora cordifolia and Tinospora sinensis . Ind J Pharm Sci. 2008;70:96–99. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 26. Li L, Long W, Wan X, Ding Q, Zhang F, Wan D. Studies on quantitative determination of total alkaloids and berberine in five origins of crude medicine “Sankezhen”. J Chromatogr Sci. 2015;53:307–311. [DOI] [PubMed] [Google Scholar]
- 27. Ghassempour A, Heydari R, Talebpour Z, Fakhari AR, Rassouli A, Davies N, et al. Study of new extraction methods for separation of anthocyanins from red grape skins: analysis by HPLC and LC‐MS/MS. J Liq Chromatogr Relat Technol. 2008;31:2686–2703. [Google Scholar]
- 28. Heydari R, Hosseini M. Determination of the fatty acid composition of Amygdalus scoparia kernels from iron using gas chromatography‐mass spectrometry. Chem Nat Compd. 2017;53:538–539. [Google Scholar]
- 29. Shi H‐L, Peng S‐L, Sun J, Liu Y‐M, Zhu Y‐T, Qing L‐S, et al. Selective extraction of berberine from Cortex phellodendri using polydopamine‐coated magnetic nanoparticles. J Sep Sci. 2014;37:704–710. [DOI] [PubMed] [Google Scholar]
- 30. Jiang L‐F, Chen B‐C, Chen B, Li X‐J, Liao H‐L, Zhang W‐Y, et al. Aptamer‐functionalized Fe3O4 magnetic nanoparticles as a solid‐phase extraction adsorbent for the selective extraction of berberine from Cortex phellodendri . J Sep Sci. 2017;40:2933–2940. [DOI] [PubMed] [Google Scholar]
- 31. Wang Y, Yin S‐J, Zhao C‐P, Chen G‐Y, Yang F‐Q. Preparation of a zirconium terephthalate metal‐organic framework coated magnetic nanoparticle for the extraction of berberine prior to high‐performance liquid chromatography analysis. J Sep Sci. 2020;44:1220–1230. [DOI] [PubMed] [Google Scholar]
- 32. Koide T, Iwata M, Maekawa K, Saito H, Tanimoto T, Okada S. Berberine Hydrochloride Reference Standard (Control 001) of National Institute of Health Sciences. Kokuritsu Iyakuhin Shokuhin Eisei Kenkyusho Hokoku. 2001;119:97–100. [PubMed] [Google Scholar]
Associated Data
This section collects any data citations, data availability statements, or supplementary materials included in this article.
Data Availability Statement
All data are given in the manuscript. Data sharing is not applicable to this article as no datasets were generated or analyzed during the current study.
