Skip to main content
ACS Omega logoLink to ACS Omega
. 2026 Sep 18;11(38):57449–57463. doi: 10.1021/acsomega.6c05796

Dual-Functional Plasmonic Z‑Scheme Bi2WO6/Ag/CuS Ternary Nanocomposite for Photocatalytic Oxidation of Tetracycline and Reduction of Cr (VI) under Visible Light

Girija Shankar Jena 1, Rajakumar Ananthakrishnan 1,*
PMCID: PMC13629063  PMID: 42825060

Abstract

The simultaneous removal of antibiotic pollutants and toxic heavy metals from wastewater remains challenging because of limited visible-light utilization and rapid recombination of photogenerated charge carriers in conventional photocatalysts. Integrating plasmonic nanostructures into semiconductor heterojunctions provides an attractive route to simultaneously enhance light harvesting and photocatalytic redox activity. In this work, a plasmonic Bi2WO6/Ag/CuS ternary nanohybrid was fabricated through sequential photodeposition of Ag nanoparticles onto hierarchical Bi2WO6 microspheres, followed by the in situ growth of CuS. The incorporation of Ag nanoparticles promotes interfacial charge transfer and enhances visible-light harvesting through the surface plasmon resonance effect. The photocatalytic activity of the ternary nanohybrid was assessed through tetracycline (TC) oxidation and Cr (VI) reduction under visible-light irradiation. The optimized ternary nanohybrid achieved 92% TC degradation and 90% Cr (VI) reduction within 60 min, corresponding to apparent rate constants of 0.0336 and 0.0322 min–1, respectively. Furthermore, enhanced removal efficiencies were observed in the coupled TC/Cr (VI) system, indicating a synergistic interaction between oxidation and reduction processes. Band-structure analysis and in situ EPR measurements verified the Ag-mediated all-solid-state Z-scheme charge-transfer pathway. LC–MS analysis and phytotoxicity assessment revealed the progressive degradation of TC into less toxic intermediates. The photocatalyst also exhibited good stability and considerable activity in real water matrices, highlighting its potential for practical solar-driven wastewater remediation.


graphic file with name ao6c05796_0014.webp


graphic file with name ao6c05796_0012.webp

1. Introduction

Semiconductor-assisted heterojunction photocatalysts are essential for enhancing solar energy conversion into chemical energy owing to their ability to facilitate rapid charge separation. These heterojunctions, formed at the interface between two dissimilar crystalline semiconductors, play a significant role in various applications, including hydrogen evolution, pollutant degradation, and solar cells. , The effectiveness of these systems depends on three key factors: light absorption capacity, charge separation efficiency, and effective charge migration for redox reactions. Designing heterostructures that optimize these aspects is crucial for developing ideal photocatalysts. , Globalization and industrialization have led to significant environmental challenges, including water pollution caused by the overuse of antibiotics such as tetracycline hydrochloride, penicillin, and sulfamethoxazole, as well as the improper disposal of heavy metals ions like Hg2+, Cd2+, Pb2+, and Cr6+. These pollutants pose serious risks to all forms of life due to their carcinogenic, teratogenic, and mutagenic properties. − In this context, researchers are aiming to develop semiconductor-based photocatalysts as a green approach to address these environmental problems. Our research group focuses on the preparation of visible light active semiconductor-based photocatalysts for the environmental remediation of persistent organic pollutants (POPs), dyes, and heavy metals in water and wastewater. , Among the various semiconductors studied for photocatalysis, TiO2, and ZnO are promising candidates due to their nontoxic nature, affordability, and excellent stability. However, their limited efficiency under visible light restricts their broader usage in photocatalysis. Thus, it is vital to develop modified heterojunction photocatalysts for utilizing visible light and to offer enhanced performance in environmental remediation.

In the recent past, Bi-based photocatalysts have attracted a lot of attention especially because of their remarkable ability to respond to visible light, nontoxic nature, and their chemical stability. A wide array of bismuth materials, such as Bi2WO6, BiVO4, Bi2Sn2O7, BiO2–x, and BiOX (where X = Cl, Br, and I), have procured significant success in the domain of organics degradations. − Their photocatalytic behavior mainly arises from the hybridization between the Bi 6s orbital and the O 2p orbital at the valence band edge, which results in a suitable band gap for visible-light absorption. Consequently, these materials emerge as up-and-coming candidates for photocatalytic applications. Bi2WO6 is an effective bismuth containing metal oxide for photocatalytic applications, attributed to its narrow bandgap of 2.7 eV, stability under light exposure, and eco-friendliness. However, its photocatalytic efficiency is compromised by rapid charge recombination and slow electron transfer processes. ,, To address these issues, hybrid or multi-component photocatalysts featuring heterojunctions, p–n junctions, or Schottky junctions are being developed to enhance charge transport and minimize recombination. Transition metal sulfides like MoS2, CdS, and CuS exhibit notable electrical, optical, and catalytic characteristics. − Specifically, CuS, recognized for its nontoxic and economical nature as a p-type semiconductor, has been integrated with Bi2WO6 to create a p-n heterojunction that enhances performance. However, the redox potential of electrons and holes is diminished during transfer in traditional heterojunctions (type-I, type-II, and p-n heterojunction) processes, which negatively impacts the efficiency of photocatalytic reactions. The Z-scheme charge transfer strategy has attracted significant attention because it preserves strong redox capability while promoting efficient charge separation. In this mechanism, low-energy charge carriers recombine at the interface, while highly energetic electrons and holes are retained to drive reduction and oxidation reactions, respectively. Z-scheme photocatalytic systems can be classified as either direct or indirect depending on the involvement of electron mediators. Several direct Z-scheme photocatalytic systems, such as BiVO4/WO3, FAPbBr3/Bi2WO6 and Ag2CrO4/g-C3N4, − have shown better performance compared to individual photocatalysts. However, in certain semiconductor heterojunctions, the conventional transfer of charges may compete with the Z-scheme mechanism. In the past three decades, artificial Z-scheme systems have been developed, inspired by natural photosynthesis processes. The indirect Z-scheme incorporates electron mediators, which may be noble or nonmetal mediators, to enhance charge separation. Nobel metals generally enhance electron transfer through localized surface plasmon resonance (LSPR) and help mitigate traditional semiconductor bandgap limitations. ,, It has been reported that Ag NPs enhance electron density and photocatalytic performance when combined with Bi2WO6. Zhu et al. showed that Ag NPs in a hybrid Ag/Fe3O4/g-C3N4 photocatalyst improves light absorption and activity, highlighting the role of LSPR in creating efficient Z-scheme photocatalysts. Reactive oxygen species (ROS) formation is an important parameter that governs various photocatalytic processes. Unlike binary systems such as Bi2WO6/CuS and BiVO3/WO3, , typically generate hydroxyl radicals (•OH), while systems like FAPbBr3/Bi2WO6 and Bi2WO6/Ag, , primarily produce superoxide radicals (•O2 –). However, limited studies focus on systems generating multiple ROS simultaneously. This work aims to design a Z-scheme ternary heterojunction to facilitate the simultaneous production of numerous ROS, enhancing redox efficiency.

In this study, a hierarchical Bi2WO6/Ag/CuS Z-scheme composite was fabricated through a facile two-step wet-chemical strategy. In this system, Ag nanoparticles act as electron-transfer mediators and plasmonic sensitizers, which facilitate the recombination of electrons from Bi2WO6 with holes from CuS. Moreover, the strong affinity of Ag toward sulfur promotes the effective deposition of CuS on the Bi2WO6 surface. The structural, physicochemical, and optoelectronic characteristics of the resulting composite were systematically examined using various analytical techniques. The photocatalytic activity of the material was assessed through the degradation of tetracycline (TC) in aqueous solution under visible-light irradiation. Furthermore, the ternary composite was also employed for the reduction of Cr (VI) under optimized experimental conditions. The degradation intermediates produced during TC transformation were carefully identified, and the photocatalytic reaction mechanism was proposed based on the combined experimental and characterization results.

2. Experimental Section

All chemicals used in this study were of analytical grade and were used as received without further purification. Details of the chemicals and their suppliers are provided in the Supporting Information.

2.1. Synthesis of Bi2WO6 (BWO)

BWO was prepared via a hydrothermal method. Initially, bismuth nitrate (970 mg, 2 mmol) was dissolved in 10 mL of ethylene glycol under continuous stirring for 30 min to obtain solution A. Separately, Na2WO4·2H2O (330 mg, 1 mmol) was dissolved in 20 mL of deionized water to form solution B. Solution B was then added dropwise into solution A under vigorous stirring to obtain a homogeneous mixture. The resulting suspension was transferred into a 60 mL Teflon-lined stainless-steel autoclave and maintained at 160 °C for 24 h. After cooling to room temperature, the precipitate was collected by centrifugation and repeatedly washed with deionized water followed by ethanol to remove residual impurities. Finally, the obtained product was dried overnight at 60 °C to yield the BWO powder.

2.2. Synthesis of CuS

In a typical hydrothermal synthesis, Cu­(NO3)2·3H2O (1.208 g, 5 mmol) was dissolved in 40 mL ethanol and magnetically stirred for 30 min to obtain a homogeneous solution. Subsequently, Na2S2O3·5H2O (1.24 g, 5 mmol) was added to the solution under continuous stirring. The resulting mixture was transferred into a 60 mL Teflon-lined stainless-steel autoclave and heated at 90 °C for 4 h. After cooling to room temperature, the precipitate was collected by centrifugation and washed several times with deionized water and ethanol. Finally, the obtained product was dried at 60 °C for 12 h to obtain the CuS powder.

2.3. Synthesis of Bi2WO6@Ag (BWO/Ag)

The BWO/Ag hybrids were synthesized using a photoreduction technique. A specific amount of AgNO3 and 200 mg of prepared Bi2WO6 were typically put into a 20 ml methanol solution (20 Vol %). The suspension was continuously stirred for 2 h under visible-light irradiation using a 250 W lamp. The product was centrifuged, followed by washing and drying at 60 °C. The resulting samples were labeled BWO/2% Ag, BWO/4% Ag, BWO/6% Ag, and BWO/10% Ag, corresponding to mass ratio of Ag to BWO were 2%, 4%, 6%, and 10% respectively.

2.4. Synthesis of BWO/Ag/CuS

The BWO/Ag/CuS composite materials were synthesized via a hydrothermal approach. Initially, a specified quantity of the pre-synthesized BWO/Ag powder was dispersed in 30 mL of ethanol and magnetically stirred for 30 min to obtain a uniform suspension. Subsequently, 0.2 mmol of Cu­(NO3)2·3H2O and 0.2 mmol of Na2S2O3·5H2O were introduced into the dispersion under continuous stirring for an additional 30 min. The resulting mixture was then transferred into two 50 mL Teflon-lined stainless-steel autoclaves and maintained at 90 °C for 4 h. After completion of the reaction, the precipitate was separated by centrifugation, thoroughly washed with deionized water and ethanol, and dried at 60 °C for 12 h. The obtained samples were denoted as x BWO/Ag/CuS, where x represents the mass percentage of CuS in the composite (x = 5%, 10%, and 15%). For comparison, BWO/10% CuS was prepared following the same procedure using pristine BWO nanoparticles instead of BWO/Ag. Furthermore, for clarity in subsequent discussions, BWO/Ag and BWO/Ag/CuS refer to the optimized compositions of BWO/4% Ag and BWO/4% Ag/10% CuS, respectively. A schematic representation of the synthesis procedure for the BWO/Ag/CuS photocatalyst is provided in Scheme .

1. Graphical Representation of the Synthesis of a Sample.

1

2.5. Characterization of Materials

Powder X-ray diffraction (XRD) patterns were recorded using a Bruker D8 Advance diffractometer with Cu Kα radiation. The morphology and elemental composition were examined by field-emission scanning electron microscopy (FESEM/EDS, FEI Nova NanoSEM 450) and high-resolution transmission electron microscopy (HRTEM, JEOL JEM-2010). UV–vis diffuse reflectance spectra were collected using a Cary 5000 UV–vis–NIR spectrophotometer (Agilent Technologies). The chemical states of the elements were analyzed by X-ray photoelectron spectroscopy (XPS, PHI 5000 VersaProbe II). Raman spectra were recorded using a Renishaw Raman spectrometer. The specific surface area was determined using a Micromeritics 3Flex analyzer. Solid-state photoluminescence (PL) spectra were recorded using a Horiba Fluorolog-3 spectrofluorometer. Photoelectrochemical measurements were carried out using a Biologic SP-150 electrochemical workstation in a conventional three-electrode system. Inductively coupled plasma mass spectrometry (ICP–MS) analysis was performed using a Thermo Scientific iCAP Q instrument.

2.6. Photocatalytic Performance Evaluation

The photocatalytic activity of the synthesized catalysts was assessed through the reduction of Cr (VI) using potassium dichromate (K2Cr2O7) as the Cr (VI) source at pH 3.5. The reactions were performed under visible-light irradiation provided by a 250 W tungsten lamp (λ ≥ 420 nm). A 15% aqueous NaNO2 solution was used as an optical filter to remove wavelengths below 420 nm. The distance between the light source and the reaction solution was maintained at 25 cm, and the light intensity at the reaction position was measured to be 0.0048 W cm–2. In a typical experiment, 20 mg of catalyst was dispersed in 40 mL of Cr (VI) solution (40 mg L–1) and magnetically stirred in the dark for 60 min to establish adsorption–desorption equilibrium. Subsequently, the suspension was irradiated for 60 min, and 1 mL aliquots were withdrawn at regular intervals to monitor the reaction progress. The reaction temperature was maintained at room temperature using a circulating water-cooling system. The reduction of Cr (VI) to Cr (III) was determined by the diphenylcarbazide (DPC) colorimetric method, with absorbance measured at 545 nm. For comparison, tetracycline (TC, 50 mg L–1) was employed as a model pollutant for photocatalytic degradation under the same experimental conditions, except that the reaction was carried out at neutral pH.

The degradation percentages for all experiments were calculated using the expression:

Degradation(%)=C0−CtC0×100% 1

where C 0 represents the initial concentration of the pollutant and C t denotes the concentration at a given reaction time.

3. Results and Discussion

3.1. PXRD of Synthesized Materials

The crystal phases and structural properties of the synthesized heterostructured BWO/Ag/CuS heterostructures were examined by X-ray diffraction (XRD), as shown in Figure a. The presence of sharp and intense diffraction peaks indicates the formation of highly crystalline materials. The prominent diffraction peaks observed at 28.3, 32.8, 32.9, 47.0, 47.1, 55.8, 56.0, and 58.6 can be precisely attributed to the crystal planes (1 3 1), (2 0 0), (0 0 2), (2 6 0), (2 0 2), (3 3 1), (1 3 3), and (2 6 2) of orthorhombic BWO (JCPDS card no-39–0256). In addition, the diffraction pattern of CuS matches that of hexagonal covellite CuS (JCPDS card No. 78–2121). Peaks at 2θ angles of 27.7, 29.3, 31.8, 32.9, 38.8, 48.0, 52.7, and 59.3 are identified and correspond to the (1 0 1), (1 0 2), (1 0 3), (0 0 6), (1 0 5), (1 1 0), (1 0 8), and (1 1 6) planes, respectively. The PXRD pattern of the BWO/Ag/CuS composite closely resembles that of bare BWO, indicating an orthorhombic BWO structure. The absence of distinct peaks for CuS and Ag can be attributed to their low loading, small particle size, and good dispersion within the composite. The enlarged patterns shown in Figure b provide a clearer view of the peak positions. A slight shift of the diffraction peaks toward lower 2θ values is observed for the BWO/Ag/CuS sample compared to BWO. This shift suggests lattice expansion, which can be related to interfacial interactions between the components, leading to lattice strain within the BWO structure. , Raman spectra further corroborate the phase composition of BWO, BWO/Ag, BWO/Ag/CuS, and CuS (Figure c,d). The spectra exhibit prominent bands at 795 and 828 cm–1, corresponding to the symmetric and antisymmetric stretching vibrations of terminal O–W–O groups. Bands observed in the 700–740 cm–1, region are attributed to the asymmetric stretching of WO6 octahedra. Bands at 262, 285, and 309 cm–1 are attributed to O–W–O bending vibrations, while the mode at 418 cm–1 corresponds to equatorial bending. Low-frequency bands around 143–154 cm–1 arise from Bi–O lattice vibrations. Upon Ag incorporation, a slight red shift and peak broadening of the O–W–O stretching modes are observed, indicating interaction with the BWO lattice. In addition, the characteristic band near 470 cm–1, assigned to S–S stretching vibration as evident from the CuS spectrum, confirms the incorporation of CuS into the composite. These variations in band position and shape reflect structural interaction among the constituent phases.

1.

1

(a) PXRD patterns of the prepared BWO, BWO/Ag, CuS, and BWO/Ag/CuS nanocomposites. (b) enlarged PXRD profiles of BWO-based samples; (c) Raman spectra of BWO, BWO/Ag, and BWO/Ag/CuS nanocomposites; and (d) Raman spectra of pristine CuS.

3.2. Morphological Analysis

The morphology of the synthesized BWO and its composites was analyzed using FESEM. The pristine BWO exhibited a hierarchical flower-like microsphere with an average diameter of 2–4 μm, composed of interconnected nanoplates (Figure a). Pristine CuS particles also displayed a micro flower-like morphology (Figure b). The binary BWO/Ag nanocomposite retained a morphology similar to pure BWO, with cuboidal agglomerated Ag nanoparticles (70–100 nm) deposited on the BWO nanoplates (Figure S1). In the ternary BWO/Ag/CuS composite, the CuS micro flowers were anchored onto the BWO nanoplates through Ag nanoparticles, resulting in a rougher texture than the pristine BWO flowers (Figure c). The FESEM–EDX spectrum of the BWO/Ag/CuS composite shows the presence of Bi, W, O, Ag, Cu, and S elements without any detectable impurity signals (Figure S2). Elemental mapping further reveals a uniform distribution of these elements across the composite surface, indicating effective incorporation of Ag and CuS within the BWO matrix (Figure S3). TEM images further demonstrate the morphology of the synthesized BWO/Ag/CuS ternary composite (Figure d,e), revealing slight particle agglomeration with nanoparticle sizes ranging from 100 to 300 nm. The HRTEM image confirms the presence of BWO, Ag, and CuS in the composite by analyzing the lattice d-spacing (Figure f). BWO shows lattice fringes corresponding to the (133) planes with a d-spacing of 0.164 nm. CuS exhibits distinct fringes associated with the (102) planes at a d-spacing of 0.304 nm. In addition, cubic Ag is identified by the (002) planes with a d-spacing of 0.23 nm. These observations collectively confirm the successful formation of the BWO/Ag/CuS composite.

2.

2

FESEM images of (a) BWO, (b) BWO/Ag, and (c) BWO/Ag/CuS, (d) TEM image of BWO/Ag/CuS nanocomposites, and (e, f) HRTEM image of the synthesized BWO/Ag/CuS.

3.3. Chemical Composition and Specific Surface Area Studies

X-ray photoelectron spectroscopy (XPS) was employed to investigate the surface composition and electronic structure of the BWO/Ag/CuS ternary nanocomposite. The survey spectrum (Figure a) showed Bi, W, O, Cu, S, and Ag and a 284.6 eV C peak, likely from hydrocarbon contamination. The high-resolution spectra of Bi 4f, W 4f, Cu 2p, O 1s, and Ag 3d for the BWO/Ag/CuS composite are shown in Figure b-f. In the Bi 4f spectrum (Figure b), two characteristic peaks located at 159.0 and 164.37 eV correspond to Bi 4f7/2 and Bi 4f5/2, respectively, with a spin–orbit splitting of approximately 5.3 eV, confirming the presence of Bi3+ species. Additional weak peaks at 157.2 and 162.5 eV are attributed to metallic Bi species. The W 4f spectrum (Figure c) shows peaks at 35.2 and 37.4 eV assigned to W6+ (W 4f5/2 and W 4f7/2). Additional peaks at 34.4 and 36.6 eV indicate W5+ species related to oxygen vacancies. , Compared with pristine BWO the ternary composite exhibits a slight negative shift of about 0.2 eV which suggests changes in electron density due to defect formation. A weak signal near 41.9 eV is attributed to the W 5p3/2 orbital. High-resolution O 1s spectra with primary peaks at 529.3 and 530.7 eV corresponding to lattice oxygen species within the layer-structured Bi (Bi–O, W–O) system (Figure d). Two prominent peaks at 368 and 374 eV can be attributed to Ag 3d5/2 and Ag 3d3/2, respectively (Figure e). Peak fitting shows that the primary binding energy peaks at 367.1 and 373.1 eV are associated with Ag+. In contrast, the weaker peaks at 368.1 and 374.1 eV indicate the presence of metallic Ag0. , In Figure f, Cu 2p spectra show distinct peaks for Cu 2p3/2 and Cu 2p1/2 at binding energies of 932.2 and 952.1 eV, respectively, along with a Cu2+ shake-up peak at 942 eV. High-resolution spectra were obtained for the S 2s region to confirm the presence of S2– ions since the Bi 4f peak obscured the S 2p area. In Figure S4, the broad peak at 225.7 eV indicates the presence of sulfide ions within the CuS component. The slight positive shifts (≈0.1–0.2 eV) of the Bi 4f, W 4f, and O 1s peaks relative to pristine BWO indicate a decrease in electron density around the Bi2WO6 framework (Figure S5). Such shifts suggest interfacial charge redistribution and Fermi-level equilibration among BWO, Ag, and CuS, evidencing strong electronic coupling within the heterostructure. The resulting electronic interaction may facilitate carrier migration across the heterointerface and contribute to improved charge-separation efficiency.

3.

3

High-resolution XPS spectra of BWO/Ag/CuS nanocomposites (a) survey scan, (b) Bi 4f, (c) W 4f, (d) O 1s, (e) Ag 3d, and (f) Cu 2p.

Furthermore, the N2 adsorption-desorption analysis was conducted on both BWO and BWO/Ag/CuS nanocomposite (Figure S6). The BWO/Ag/CuS nanocomposite showed increased specific surface area compared to BWO. Results indicated specific surface areas of 13.05 m2 g–1 for BWO and 15.5 m2 g–1 for BWO/Ag/CuS, with pore volumes of 0.014 cm3 g–1 and 0.017 cm3 g–1. The increase in surface area can be related to the deposition of Ag and CuS nanoparticles on the BWO surface. This structural modification is expected to create additional exposed active sites and improve the interaction between the catalyst and reactant molecules, which may contribute to enhanced photocatalytic performance.

3.4. Optical Absorption and Photo-Electronic Properties

The optical behavior of synthesized BWO, CuS, BWO/Ag, BWO/CuS, and BWO/Ag/CuS samples were analyzed using UV-Vis diffuse reflectance spectroscopy (DRS) and photoluminescence (PL). As shown in Figure a, BWO has an absorption edge starting at around 450 nm, while CuS exhibits extensive absorption across the visible spectrum. The incorporation of Ag nanoparticles into BWO improves visible-light absorption and produces an additional band around 510 nm, which is associated with the surface plasmon resonance (SPR) effect of Ag nanoparticles. The further introduction of CuS into the BWO/Ag system extends the absorption range from the UV–visible region to the near-infrared region, enabling the ternary composite to utilize a wider portion of the solar spectrum. Band gap energies calculated from the Tauc plots (Figure b) are 2.60 eV for BWO, 2.29 eV for BWO/CuS, and 2.16 eV for BWO/Ag/CuS, indicating improved light-harvesting capability in the composite materials. Photoluminescence spectra were recorded with an excitation wavelength of 330 nm to evaluate charge carrier recombination. All samples display an emission peak near 468 nm, while pristine BWO shows the highest PL intensity (Figure S7), indicating rapid recombination of photogenerated carriers. In contrast, the BWO/Ag/CuS composite exhibits the weakest PL emission, suggesting more efficient separation of electron–hole pairs due to the interaction among BWO, Ag, and CuS components.

4.

4

(a) UV–vis absorption spectra (DRS), (b) Tauc plots of pristine BWO, BWO/CuS, and BWO/Ag/CuS, (c) and (d) transient photocurrent response and EIS Nyquist plot of BWO, BWO/Ag, BWO/CuS, and BWO/Ag/CuS.

To further investigate the charge transfer behavior, photoelectrochemical measurements such as photocurrent response (PC) and electrochemical impedance spectroscopy (EIS) were carried out. As shown in Figure c, the BWO/Ag/CuS composite exhibits the highest photocurrent density among all samples, indicating more efficient separation and migration of photogenerated charge carriers. All the prepared samples displayed stable and repeatable photocurrent profiles during successive light irradiation cycles, reflecting excellent photostability. The EIS results (Figure d) show that the BWO/Ag/CuS composite possesses the smallest semicircle radius in the Nyquist plot, which corresponds to the lowest charge transfer resistance. The resistance follows the order BWO > BWO/Ag > BWO/CuS > BWO/Ag/CuS, confirming that the ternary composite promotes faster interfacial charge transfer and suppresses electron–hole recombination.

3.5. Photocatalytic Degradation of TC

The photocatalytic activity of the synthesized materials was evaluated using tetracycline (TC) as a model pollutant under visible-light irradiation. Before illumination, all suspensions were stirred in the dark for 60 min to attain adsorption–desorption equilibrium, followed by 60 min of photocatalytic degradation. The effects of Ag and CuS loading, together with other parameters influencing TC removal, were systematically examined.

3.5.1. Impact of Ag and CuS Contents

The effects of Ag and CuS loading on the photocatalytic degradation of TC were investigated to identify the optimum composition of the ternary heterostructure. As shown in Figure S8a, the photocatalytic activity of BWO/Ag composites initially increased with increasing Ag content and reached a maximum at 4 wt % Ag. The optimized BWO/4%Ag sample achieved 63% degradation within 60 min, compared to 50% for pristine BWO. The enhanced activity can be attributed to improved visible-light utilization and charge separation induced by the incorporation of Ag nanoparticles. However, a further increase in Ag content resulted in a gradual decline in photocatalytic activity, which may be due to the formation of excessive Ag domains that promote charge recombination and partially block active surface sites. To further enhance the photocatalytic performance, CuS was introduced into the optimized BWO/4%Ag composite to construct a ternary BWO/Ag/CuS heterostructure. As shown in Figure S8b, the degradation efficiency increased with increasing CuS content and reached a maximum at 10 wt %, followed by a decrease at 15 wt %. The improved activity at lower CuS loading is attributed to the formation of an efficient heterojunction that facilitates charge separation and transfer. However, at higher CuS loading, the formation of CuS–CuS homojunctions promotes charge carrier recombination, leading to a decrease in photocatalytic efficiency. These results indicate that an optimal loading of Ag and CuS is essential to achieve efficient charge separation and improved photocatalytic activity. For comparison, the photocatalytic degradation of TC over BWO, CuS, BWO/Ag, BWO/CuS, and BWO/Ag/CuS was evaluated under identical conditions (Figure a). At first, the prepared catalyst was mixed with TC solution and stirred in the dark for 60 min to reach adsorption equilibrium. The ternary BWO/Ag/CuS composite showed the highest adsorption rate, likely due to its larger surface area, and achieved 92% TC degradation within 60 min irradiation. Based on the UV–Vis calibration curve (Figure S8c), the residual TC concentration decreased from an initial 50 mg L–1 to approximately 3.5 mg L–1 after 60 min of photocatalytic treatment. As shown in Figure b, the characteristic absorption band of TC at 357 nm undergoes a noticeable redshift after contact with the BWO/Ag/CuS photocatalyst, followed by a progressive decrease in absorption intensity during visible-light irradiation. This peak shifting can be attributed to interactions between TC molecules and surface oxygen-vacancy sites, which modify the electronic structure of TC and enhance π-conjugation. The subsequent decrease in absorption intensity reflects the continuous degradation of TC during the photocatalytic process.

5.

5

(a) Plot of (Ct/C0) vs time for photodegradation of TC, (b) UV-Vis absorption spectra of TC at various intervals of times, (c) first-order kinetic study for TC degradation, and (d) effect of initial solution pH on the degradation of TC over of BWO/Ag/CuS nanocomposite.

The photodegradation process was studied using a pseudo-first-order kinetic model to determine reaction kinetics. The reaction rate constant (k, min–1) can be calculated using the formula.

ln(Ct/C0)=kt 2

C t and C 0 are the TC concentrations at different time intervals and 0 min, respectively (Figure c), showing the prepared catalyst’s apparent rate constant (k). The pristine BWO and CuS exhibit relatively low k-values of 0.009 min–1 and 0.005 min–1, respectively. In contrast, ternary BWO/Ag/CuS nanocomposites have higher k values than other materials evaluated, with the highest value being 0.0336 min–1 under the same condition. The k-values of the ternary system are 6.72 times and 3.73 times greater than those of CuS and BWO, respectively. To distinguish the effect of heterostructure formation from simple component mixing, a comparison with a mechanically mixed (BWO + Ag + CuS) sample was performed (Figure S8d). The synthesized BWO/Ag/CuS heterostructure exhibited significantly higher photocatalytic activity than the physical mixture. This enhancement results from the well-established heterointerface formed during synthesis, which promotes efficient interfacial charge transfer and suppresses charge-carrier recombination.

3.5.2. Effects of Operational Factors on Photocatalytic TC Degradation

3.5.2.1. Impact of Solution pH on TC Degradation

The pH of the reaction medium significantly influences photocatalytic TC degradation by affecting both TC speciation and the surface charge of the photocatalyst. As shown in Figure d, the degradation efficiency strongly depended on solution pH, with the highest activity observed at near-neutral conditions. Zeta-potential measurements (Figure S9a) revealed a pHzpc of approximately 4.3, indicating a positively charged surface below this value and a negatively charged surface above it. TC predominantly exists as the cationic species (H3A+) at pH < 3.3, the zwitterionic species (H2A) between pH 3.3 and 7.7, and the anionic species (HA– and A2–) at pH > 7.7. At near-neutral pH, where TC mainly exists as H2A, favorable interactions between TC molecules and the catalyst surface promote adsorption and degradation. In contrast, under strongly alkaline conditions (pH 11), both the catalyst surface and TC molecules are negatively charged, leading to electrostatic repulsion and reduced degradation efficiency. In strongly acidic media, excess H+ ions consume photogenerated electrons and hinder •O2 – generation, resulting in lower photocatalytic activity. These results indicate that near-neutral pH provides the most favorable environment for TC degradation. Therefore, the reduced activity observed under strongly acidic and alkaline conditions is primarily associated with pH-dependent TC speciation and surface-charge interactions.

3.5.2.2. Impact of Initial TC Concentration on TC Degradation

The initial concentration of TC also affects the process of degradation. In Figure S9b shows that the degradation efficiency decreased from 92% to 49% with an increase in the concentration of the TC between 50 and 80 mg L–1. This reduction can be explained by the limited penetration of light and the increased competition among TC molecules for the available active sites on the catalyst surface. Therefore, an initial TC concentration of 50 mg L–1 was selected as the optimal condition for subsequent photocatalytic experiments. Furthermore, the kinetic behavior of TC degradation at a lower concentration (20 mg L–1) was analyzed for different synthesized samples (Figure S9c). The ternary BWO/Ag/CuS composite shows a kinetic rate constant of 0.0635 min–1, which is approximately 9.33 times higher than that of pristine BWO, highlighting the superior photocatalytic performance of the ternary system.

3.5.2.3. Impact of Inorganic Ions and Humic Acid on TC Degradation

The influence of common inorganic ions and natural organic matter (NOM), represented by humic acid (HA), on TC degradation was evaluated (Figure S9d). HA produced the strongest inhibition, reducing the degradation efficiency to 45%. This decrease mainly results from competitive adsorption on the catalyst surface, scavenging of reactive oxygen species, and light-shielding effects. Among the inorganic ions, Cl – and CO3 2– caused the greatest decrease in photocatalytic activity, lowering the degradation efficiency to 68% and 72%, respectively. The inhibition by Cl – results from competitive adsorption and its reaction with photogenerated holes and •OH radicals to form less reactive chlorine radical species (•ClOH– and •Cl), which reduces the availability of reactive species for TC degradation. CO3 2 – reacts with the dominant •O2 – radicals to produce less reactive CO3 •– radicals, leading to a further decrease in degradation efficiency. Similarly, SO4 2– also reduced the photocatalytic activity by reacting with photogenerated holes to form SO4 •– radicals, which have lower oxidation activity toward TC than •OH radicals. , In contrast, NO3 – had only a minor influence, and the degradation efficiency remained at 87% because of its relatively low reactivity toward the reactive species involved in the photocatalytic process. These results show that the BWO/Ag/CuS photocatalyst maintains satisfactory activity in the presence of common water constituents.

3.5.2.4. Influence of Real Water Matrices on TC Degradation

The practical applicability of the photocatalyst was further assessed using tap water and wastewater as reaction media (Figure S9e). Compared with deionized water, the degradation efficiency decreased slightly to 85% in tap water, likely due to the presence of turbidity and low concentrations of dissolved ions. A more noticeable decline was observed in wastewater, where the degradation efficiency reached 72%. This reduction can be attributed to the higher levels of inorganic ions, organic matter, and suspended solids, which interfere with pollutant adsorption and light transmission. However, the photocatalyst maintained appreciable activity in both water matrices, demonstrating its potential for application in complex water environments.

3.5.3. Photocatalytic Degradation Pathway of TC and Phytotoxicity Assessment

To clarify the degradation mechanism of TC over the BWO/Ag/CuS photocatalyst, LC–MS analysis was performed to identify the major photodegradation intermediates (Figure ). The chromatograms shown in Figure S10 compare the reaction mixtures collected at 0, 30, and 60 min. The characteristic TC peak observed at a retention time of 0.80 min decreased significantly with increasing irradiation time, indicating progressive degradation of the parent molecule. The corresponding mass spectra (Figure S11) revealed several intermediate species formed during the reaction. The peak at m/z = 445 detected at 0 min corresponds to the parent TC molecule. Previous studies have reported that TC is highly susceptible to attack by reactive oxygen species owing to the presence of electron-rich functional groups, including the CC bond, phenolic hydroxyl groups, and amino substituents. In pathway I, hydroxyl radical attack on the Ca-Cb bond leads to the formation of the hydroxylated intermediate P1 (m/z = 461), while subsequent hydroxylation generates P2 (m/z = 477), which is consistent with previously reported LC–MS analyses of TC degradation. − As the reaction proceeds, P2 undergoes successive oxidation, ring opening, demethylation, and fragmentation reactions to produce lower-molecular-weight species such as P3 (m/z = 214), as reported in earlier photocatalytic studies. , In pathway II, TC is initially attacked by reactive species and subsequently undergoes oxidation and ring-opening reactions through intermediate P4, ultimately yielding P5 (m/z = 228), which agrees well with degradation products identified in previous reports. , Continued oxidation of these intermediates results in the formation of smaller organic fragments, which are eventually mineralized into CO2, H2O, and inorganic nitrogen-containing species. ,−

6.

6

Possible photodegradation pathways and intermediate products of TC.

To ensure the environmental safety of the treated water, ecotoxicity was evaluated using Vigna radiata (mung bean) germination, as illustrated in Figure . Germination tests were conducted at ambient temperature using distilled water (a1–a3), photocatalytically treated TC solution (b1–b3), photocatalyst dispersion (10 mg/50 mL) (c1–c3), and untreated TC solution (50 mg/L) (d1–d3). After 10 days, the hypocotyl lengths in distilled water, treated TC solution, and catalyst dispersion were approximately 12.5, 11.0, and 10.5 cm, respectively. The catalyst-dispersion group exhibited normal seed germination and root development, while severe growth inhibition and lesion formation were observed in the untreated TC solution. In contrast, the treated TC solution showed substantially improved root growth, indicating a significant reduction in TC toxicity after photocatalytic treatment. This behavior is likely related to the lower residual tetracycline concentration, which promotes the accumulation of reactive oxygen species (ROS) in the seeds. Consequently, the enhanced oxidative status of the roots accelerates seed germination and growth.These findings demonstrate that the BWO/Ag/CuS photocatalyst-treated solution is nontoxic to mung seed growth and can be safely used for agricultural irrigation.

7.

7

Toxicity investigation for the growth of vigina radiata: (a1-a3) distilled water, (b1-b3) photocatalyzed TC solution, (c1-c3) distilled water with catalyst, and (d1-d3) TC solution treated water.

3.6. Photocatalytic Reduction of Cr (VI)

The photocatalytic activity of the prepared materials was further evaluated to reduce toxic Cr (VI) to less harmful Cr (III) (Figure a). The ternary BWO/Ag/CuS nanocomposites demonstrated a significant decrease in Cr (VI) concentration, achieving a 90% reduction within 60 min. Absorption spectra (Figure b) confirmed effective Cr (VI) elimination. The 1,5-diphenylcarbazide (DPC) method was used for accurate Cr (VI) quantification at 540 nm, with the solution’s color change from pink to colorless, indicating successful reduction. This color change occurs because Cr (III) cannot form a complex with DPC due to its stability and inertness, while the highly oxidizing Cr (VI) forms a pink octahedral complex. The photoreduction followed a pseudo-first-order kinetic model (Figure c), with BWO/Ag/CuS showing the highest k-value of 0.0322 min–1, significantly higher than the k-values for BWO (0.0039 min–1) and CuS (0.003 min–1), indicating enhanced catalytic efficiency. Further, the kinetic behavior of Cr (VI) photoreduction at a lower concentration (20 mg/L) for various prepared samples was analyzed and is presented in (Figure S12). The ternary composite exhibits a k-value of 0.0712 min–1, 10.17 times greater than that of pristine BWO. To investigate the influence of solution pH on the reduction of Cr (VI), experiments were conducted across a pH range of 3.5 to 8.25 (Figure d). pH was adjusted using 0.1 M HCl or 0.1 M NaOH, as Cr (VI) species (HCrO4 –, Cr2O7 2–, CrO4 2–) are strongly affected by pH. Maximum reduction (90%) occurred at pH 3.5 due to enhanced adsorption of Cr2O7 2– and HCrO4 – on a more protonated surface. Conversely, at pH 8.25, reduction efficiency decreased by 17.5%, likely due to increased OH– adsorption overshadowing anion adsorption (CrO4 2–). Additionally, the formation of Cr (OH)3 precipitates blocked the active sites of the catalyst, further reducing reduction efficiency. Thermodynamically, the reduction of Cr2O7 2– to Cr3+ is more favorable than that of CrO4 2– to Cr (OH)3. Acidic conditions are thus advantageous, as the standard potential E° (Cr2O7 2– /Cr3+) is significantly higher (+1.36 eV vs. NHE) than E° (CrO4 2– /Cr (OH)3) (−0.13 eV vs. NHE).

Cr2O72−+14H++6e−→2Cr3++7H2O 3
CrO42−+4H2O+3e−→Cr(OH)3+5OH− 4

8.

8

(a) Plot of (C t/C 0) vs time for Cr (VI) photoreduction kinetics; (b) absorption spectra of Cr (VI) with BWO/Ag/CuS nanocomposite under visible light irradiation; (c) plot of ln (C t/C 0) vs time for Cr (VI) photoreduction kinetics; and (d) impact of Initial pH on Cr (VI) reduction in the presence of BWO/Ag/CuS nanocomposite.

3.7. Synergistic Photocatalytic Removal of Co-Existing TC and Cr (VI)

To evaluate the interaction between the oxidation and reduction processes, photocatalytic experiments were further conducted using a mixed TC/Cr (VI) solution under visible-light irradiation at pH 3.5. For comparison, TC degradation and Cr (VI) reduction were also examined individually under identical conditions. As shown in Figure S13, the degradation efficiency of TC increased from 73% in the single-pollutant system to 80% in the mixed system, while the reduction efficiency of Cr (VI) increased from 90% to 97%. The simultaneous enhancement of both reactions indicates a synergistic effect between TC oxidation and Cr (VI) reduction. In the coupled system, TC acts as a hole-consuming species, whereas Cr (VI) serves as an electron acceptor. The concurrent consumption of photogenerated holes and electrons suppresses charge-carrier recombination and promotes charge separation, thereby enhancing both oxidation and reduction processes. , These results further support the efficient charge-transfer characteristics of the Ag-mediated Z-scheme BWO/Ag/CuS photocatalyst.

3.8. Identification of Reactive Oxygen Species

Reactive oxygen species (ROS) generated during photocatalysis play an essential role in the degradation of organic pollutants. To determine the main active species involved in the reaction, radical scavenging experiments were carried out using specific quenching agents. p-Benzoquinone (BQ) was used to trap superoxide radicals (•O2 –), EDTA-2Na served as a hole (h+) scavenger, and isopropanol (IPA) was employed to capture hydroxyl radicals (•OH). As presented in Figure a,b, the degradation of TC was significantly inhibited by h+, • OH, and •O2 –. The significant inhibition of TC degradation under an N2 atmosphere indicates the involvement of dissolved oxygen in the photocatalytic process, while the participation of •O2 – was further supported by the BQ scavenging experiment. To further investigate the roles of •OH and •O2 – in the photocatalytic activity of the BWO/Ag/CuS nanocomposite, DMPO spin-trapping experiment was employed. Under dark conditions, no significant signals for DMPO–•OH or DMPO–•O2 – adducts were detected (Figure c,d). Upon light irradiation, a distinct 1:2:2:1 quartet signal assigned to DMPO–•OH, indicating that photoinduced holes react with adsorbed H2O to generate hydroxyl radicals. In contrast, when the reaction medium was changed from water to methanol, DMPO effectively formed an adduct with •O2 –, producing distinct signals compared to •OH. The EPR analysis confirmed that the BWO/Ag/CuS nanocomposite generates both •O2 – and •OH under visible light irradiation, which agrees well with the radical trapping experiments. These findings demonstrate that the photocatalytic performance of pure BWO is significantly improved by incorporating a multi-heterojunction structure formed by Ag NPs, CuS, and BWO within the BWO/Ag/CuS composite.

9.

9

(a) Impact of various scavengers on the photodegradation of TC; (b) histogram analysis of the impact of radical scavengers on TC degradation; (c) EPR spectra of BWO/Ag/CuS in aqueous dispersion for DMPO- • OH and (d) methanol dispersion for DMPO-•O2 –.

3.9. Photocatalytic Activity: Mechanisms and Modes in Binary and Ternary Nanocomposites

Based on the observation, a potential charge transfer mechanism for the BWO/Ag/CuS nanocomposite in TC and Cr (VI) removal is proposed in Scheme . Two typical charge transfer processes (traditional p-n heterojunction and Z-scheme) may coexist and compete in most semiconductor photocatalysts. To clarify the mechanism in the BWO/Ag/CuS system, band edge values of BWO and CuS were determined using Mott-Schottky plots (Figure S14) and UV-vis DRS spectra (Figure ). Mott-Schottky analysis determined the pristine material’s flat band potential and semiconductor type (n- or p-type) at 1000 Hz. BWO showed a positive slope, indicating an n-type semiconductor with Efb at approximately −0.37 V (vs. Ag/AgCl). In contrast, CuS showed a negative slope, suggesting a p-type semiconductor with Efb at 1.0 V relative to Ag/AgCl. Efb is often equivalent to the bottom of the conduction band (CB) for n-type semiconductors and the valence band (VB) for p-type semiconductors. The CB of BWO and VB of CuS photocatalyst was estimated at −0.28 and 1.39 V versus NHE, respectively, calculated using the following equation.

ENHE,PH=7=EAg/AgCl,pH=6.6−0.059(7−pHofelectrolyte)+0.198 5
Bandgap(eV)=Valenceband(eV)−conductionband(eV) 6

2. Possibe Photocatalytic Mechanism in the Binary BWO/CuS (a) and Ternary BWO/Ag/CuS (b) Nanocomposite Under Visible Light Irradiation.

2

The band gaps of the pristine BWO and CuS as 2.60 and 1.81 eV, respectively, determined from Tauc plots. Calculated VB for BWO and CB for CuS was approximately 2.44 eV and −0.41 eV (vs. NHE), respectively, using equation above. Under visible light irradiation, photogenerated electrons (e–) transfer from the CB of CuS to that of BWO, while holes (h+) migrate from the VB of BWO to CuS. As a result, electrons accumulate in the CB of BWO and holes in the VB of CuS, promoting efficient charge separation (Scheme a). The separated electrons cannot reduce O2 to •O2 – because its theoretical reduction potential is −0.33 V, compared to the CB potential of BWO (−0.28 V vs NHE). In general, CB of BWO cannot generate •O2 – radicals. CuS has a more negative VB potential (+1.4 V vs. NHE) than (H2O/•OH) at (+2.4 V vs NHE) and (OH–/ • OH) at (+1.99 V vs NHE), hence the VB of CuS lacks energy, it cannot generate hydroxyl radicals. The discussion and results suggest a Z-scheme type photocatalytic mechanism for BWO/Ag/CuS catalyst (Scheme b). This approach balances BWO, Ag, and CuS Fermi levels before light irradiation. BWO and CuS photoexcited by visible light generate electrons and holes. Photogenerated electrons from the CB of BWO move to metallic Ag, while Ag NPs strong surface plasmon resonance (SPR) boosts the contact’s local electric field. This field permits Ag photogenerated electrons to recombine with CuS VB holes via plasmon-induced resonance energy transfer or direct electron migration. Afterward, photogenerated (e–) in the CB of CuS combine with dissolved O2 to form •O2 –, accumulating holes in VB of BWO degrade TC molecules by direct interaction or interactions with H2O or OH– to produce •OH radicals. In Cr (VI) reduction, photogenerated electrons directly reduce Cr (VI) to Cr (III). This electron-hole migration route conserves photogenerated electrons in the negative CB of CuS and holes in the positive VB of BWO, thereby promoting efficient charge separation while preserving their strong redox ability. In addition to its SPR effect, Ag serves as an electron mediator between BWO and CuS. The observed XPS binding-energy shifts suggest interfacial charge redistribution and strong electronic coupling among BWO, Ag, and CuS, facilitating carrier migration and suppressing charge recombination. Similar to the interfacial regulation reported in S-scheme heterojunctions, the Ag-mediated interface modulates charge-transfer behavior and promotes the efficient utilization of photogenerated charge carriers for photocatalytic reactions. Therefore, the BWO/Ag/CuS heterostructure follows an Ag-mediated all-solid-state Z-scheme charge-transfer mechanism, as proposed in Scheme b. The photocatalytic reactions involved in TC degradation and Cr (VI) reduction over the BWO/Ag/CuS photocatalyst are summarized in eqs –.

BWO/Ag/CuS+hν→(h+)BWO/Ag/CuS(e−) 7
O2(ad/aq)+e−cb(Cus)→O2−•+2H++2e−cb(CuS)→OH•+−OH 8
H2O+h+Vb(BWO)→H++OH• 9
OH−+h+Vb(BWO)→OH• 10
TC+h+Vb(BWO)→degradeproduct 11
TC+OH•→degradeproduct 12
Cr(VI)+e−→Cr(III) 13

3.10. Reusability and Photocatalyst Stability

The stability of a photocatalyst is an important factor for practical applications. To evaluate the reusability of the BWO/Ag/CuS heterostructure, four consecutive photocatalytic cycles were carried out under visible-light irradiation (Figure S15a). The photocatalyst retained most of its activity toward both TC degradation and Cr (VI) reduction after four cycles, indicating good operational stability. The XRD patterns and FESEM images of the recovered catalyst showed no significant changes compared to those of the fresh sample (Figure S15b), suggesting that the crystal structure and hierarchical morphology were largely preserved during the recycling process. Furthermore, ICP–MS analysis revealed only negligible leaching of Bi, Ag, and Cu species after the photocatalytic reaction (Table S1), confirming the good chemical stability of the BWO/Ag/CuS photocatalyst. The slight decrease in photocatalytic activity after repeated cycles is likely due to surface fouling and partial blockage of active sites rather than structural degradation. A comparison of the photocatalytic performance of the present BWO/Ag/CuS catalyst with previously reported photocatalysts for TC degradation and Cr (VI) reduction is provided in Table . The BWO/Ag/CuS heterostructure exhibited competitive photocatalytic activity together with good cycling stability, demonstrating its potential for wastewater treatment applications.

1. A Comparison of Photocatalytic Degradation of TC or Reduction of Cr (VI) Using Various Reported Bi-Based Photocatalysts and under Visible Light Irradiation.

(a) Photodegradation of TC at neutral pH
Photocatalysts Concentration (mg/L) Dosage (g/L) Time (min) k (min–1) Active ROS Refs
Bi2WO6/MoS2 10 0.3 0.0309 90 •OH
BiVO4/Ag/Ag2CO3 20 0.4 0.0180 150 •OH
Bi2Sn2O7/AgI 20 1 50 0.0361 •O2 – & •OH
Bi2WO6/g-C3N4/Ag 15 0.5 60 0.0282 •O2 – & •OH
Bi2WO6/Ag/CuS 50 0.5 60 0.0336 •O2 –& •OH This work
″ 20 ″ 30 0.0635 ″ ″
(b) Photoreduction of Cr (VI) at various pH
Photocatalysts Concentration (mg/L) pH Dosage (g/L) Time (min) k (min–1) Active ROS Refs
TiO2/BiOCl 15 5 1 180 0.0133 •OH
Bi2WO6/g-C3N4 10 2 1 120 0.0414 •OH
BiOI/Bi5O7I 20 2 0.5 60 0.0432 •O2 – & •OH
BiVO4/FeVO4@rGO 20 2 0.6 90 0.0274 •O2 – & •OH
Bi2WO6/Ag/CuS 40 3.5 0.5 60 0.0322 •O2 – & •OH This work
″ 20 ″ ″ 30 0.0712 ″ ″

4. Conclusions

In this study, a Z-scheme Bi2WO6/Ag/CuS photocatalyst was successfully fabricated through a combination of photoreduction and solvothermal methods. The incorporation of Ag nanoparticles and CuS onto the Bi2WO6 surface significantly improved visible-light absorption, photocurrent response, and charge separation efficiency compared with pristine Bi2WO6 and the binary Bi2WO6/CuS system. The ternary composite exhibited a photocurrent density approximately 3.87 times higher than that of pure Bi2WO6. Under visible-light irradiation, the optimized catalyst achieved 92% degradation of TC and 90% reduction of Cr (VI) within 60 min, along with excellent stability and recyclability. The corresponding apparent rate constants for TC degradation and Cr (VI) reduction were 6.72 and 8.25 times higher than those of pristine Bi2WO6, respectively. Band-structure analysis together with EPR results confirmed an all-solid-state Z-scheme mechanism with the simultaneous generation of •OH and •O2 – radicals. In the mixed TC/Cr (VI) system, the simultaneous oxidation of TC and reduction of Cr (VI) facilitated efficient utilization of photogenerated charge carriers, thereby enhancing the overall photocatalytic performance. LC–MS analysis further identified the degradation intermediates and proposed the degradation pathway of TC. Overall, the results demonstrate that integrating Ag nanoparticles with Bi2WO6 and CuS is an effective approach for constructing efficient visible-light-driven photocatalysts for environmental remediation.

Supplementary Material

ao6c05796_si_001.pdf (2.3MB, pdf)

Acknowledgments

The authors gratefully acknowledge Indian Institute of Technology Kharagpur (IIT Kharagpur) for providing research facilities and financial support for this work. The authors also thank the Department of Science and Technology (DST), New Delhi for access to FESEM facilities, the Central Research Facility (CRF), IIT Kharagpur for TEM and HRTEM analyses, and CSIR–Central Glass and Ceramic Research Institute (CSIR-CGCRI), Kolkata for carrying out photoelectrochemical measurements.

The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsomega.6c05796.

  • FESEM images, high-resolution XPS spectra, N2 adsorption-desorption, PL spectra, loading of Ag and CuS, and comparison, pH-dependent surface charge profiles, kinetic plots, chromatogram of TC degradation, MS spectra, removal of TC, Cr (VI), their mixtures, Mott-Schottky plots and recyclable studies (PDF)

The authors declare no competing financial interest.

References

  1. Wang H., Zhang L., Chen Z., Hu J., Li S., Wang Z., Liu J., Wang X.. Semiconductor Heterojunction Photocatalysts: Design, Construction, and Photocatalytic Performances. Chem. Soc. Rev. 2014;43(15):5234–5244. doi: 10.1039/C4CS00126E. [DOI] [PubMed] [Google Scholar]
  2. Zhou Y., Zhang Y., Lin M., Long J., Zhang Z., Lin H., Wu J. C.-S., Wang X.. Monolayered Bi2WO6 Nanosheets Mimicking Heterojunction Interface with Open Surfaces for Photocatalysis. Nat. Commun. 2015;6(1):8340. doi: 10.1038/ncomms9340. [DOI] [PMC free article] [PubMed] [Google Scholar]
  3. Marschall R.. Semiconductor Composites: Strategies for Enhancing Charge Carrier Separation to Improve Photocatalytic Activity. Adv. Funct. Mater. 2014;24:2421–2440. doi: 10.1002/adfm.201303214. [DOI] [Google Scholar]
  4. Li J., Cushing S. K., Zheng P., Senty T., Meng F., Bristow A. D., Manivannan A., Wu N.. Solar Hydrogen Generation by a CdS-Au-TiO 2 Sandwich Nanorod Array Enhanced with Au Nanoparticle as Electron Relay and Plasmonic Photosensitizer. J. Am. Chem. Soc. 2014;136:8438–8449. doi: 10.1021/ja503508g. [DOI] [PubMed] [Google Scholar]
  5. Woon X.-W., Lam S.-M., Sin J.-C., Mohamed A. R., Zeng H., Li H., Huang L., Lin H., Lim J.-W.. Hydrothermally Devised Visible Light-Activated NiFe2O4/Bi4O5I2 Composite for Aquaculture Wastewater Decontamination and Plastic Waste Photoreforming Applications. Inorg. Chem. Commun. 2025;175:114188. doi: 10.1016/j.inoche.2025.114188. [DOI] [Google Scholar]
  6. Wei Q., Lam S.-M., Sin J.-C., Liu H., Su J., Dong K., Li H.. Constructing Bi2MoO6/ZnO Composite with Z-Scheme Charge Dynamics for Solar Photodegradation of Enrofloxacin and Antibacterial Trait. Inorg. Chem. Commun. 2026;186:116166. doi: 10.1016/j.inoche.2026.116166. [DOI] [Google Scholar]
  7. Lim K.-L., Sin J.-C., Lam S.-M., Zeng H., Lin H., Li H., Huang L., Mohamed A. R., Lim J.-W.. Integration of Bi2WO6 Nanoparticles onto SrTiO3 Microflowers for Efficient Solar Light-Driven Photocatalytic Cefixime Degradation and Hexavalent Chromium Reduction. Inorg. Chem. Commun. 2025;174:114063. doi: 10.1016/j.inoche.2025.114063. [DOI] [Google Scholar]
  8. Kumar A., Ananthakrishnan R., Jana G., Chattaraj P. K., Nayak S., Ghosh S. K.. An Intramolecular Charge Transfer Induced Fluorescent Chemosensor for Selective Detection of Mercury (II) and Its Self-Turn-On Inside Live Cells at Physiological pH. ChemistrySelect. 2019;4:4810–4819. doi: 10.1002/slct.201900375. [DOI] [Google Scholar]
  9. Bolisetty S., Peydayesh M., Mezzenga R.. Sustainable Technologies for Water Purification from Heavy Metals: Review and Analysis. Chem. Soc. Rev. 2019;48:463–487. doi: 10.1039/C8CS00493E. [DOI] [PubMed] [Google Scholar]
  10. Ananthakrishnan R., Goswami G. K.. Deciphering the Effect of Calcination Temperature on Crystallinity, Morphology, Oxygen Vacancy and Photocatalytic Activity of Bi-Phasic ZnO/ZnCo2O4 Heterostructured Nanomaterials. Mater. Chem. Phys. 2024;327:129792. doi: 10.1016/j.matchemphys.2024.129792. [DOI] [Google Scholar]
  11. Verma N., Ananthakrishnan R.. Boosted Charge Transfer Efficacy of an All-Solid-State Z-Scheme BiOI–CD–CdS Photocatalyst for Enhanced Degradation of 4-Nitrophenol and Oxidation of Benzyl Alcohol under Visible Light. ChemPhotoChem. 2021;5:545–558. doi: 10.1002/cptc.202000280. [DOI] [Google Scholar]
  12. Kubacka A., Fernández-García M., Colón G.. Advanced Nanoarchitectures for Solar Photocatalytic Applications. Chem. Rev. 2012;112:1555–1614. doi: 10.1021/cr100454n. [DOI] [PubMed] [Google Scholar]
  13. Li J., Wu X., Pan W., Zhang G., Chen H.. Vacancy-Rich Monolayer BiO2-x as a Highly Efficient UV-, Visible-, and Near-Infrared-Responsive Photocatalyst. Angew. Chem., Int. Ed. 2018;57:491–495. doi: 10.1002/anie.201708709. [DOI] [PubMed] [Google Scholar]
  14. Guo H., Niu C. G., Zhang L., Wen X. J., Liang C., Zhang X. G., Guan D. L., Tang N., Zeng G. M.. Construction of Direct Z-Scheme AgI/Bi2Sn2O7 Nanojunction System with Enhanced Photocatalytic Activity: Accelerated Interfacial Charge Transfer Induced Efficient Cr­(VI) Reduction, Tetracycline Degradation and Escherichia coli Inactivation. ACS Sustainable Chem. Eng. 2018;6:8003–8018. doi: 10.1021/acssuschemeng.8b01448. [DOI] [Google Scholar]
  15. Liu Y., Kong J., Yuan J., Zhao W., Zhu X., Sun C., Xie J.. Enhanced Photocatalytic Activity over Flower-Like Sphere Ag/Ag2CO3/BiVO4 Plasmonic Heterojunction Photocatalyst for Tetracycline Degradation. Chem. Eng. J. 2018;331:242–254. doi: 10.1016/j.cej.2017.08.114. [DOI] [Google Scholar]
  16. Hu X., Zhang G., Yin C., Li C., Zheng S.. Facile Fabrication of Heterogeneous TiO2/BiOCl Composite with Superior Visible-Light-Driven Performance towards Cr­(VI) and Tetracycline. Mater. Res. Bull. 2019;119:110559. doi: 10.1016/j.materresbull.2019.110559. [DOI] [Google Scholar]
  17. Wang J., Li S., Yang K., Zhang T., Jiang S., Li X., Li B.. Bacitracin-Controlled BiOI/Bi5O7I Nanosheet Assembly and S-Scheme Heterojunction Formation for Enhanced Photocatalytic Performances. ACS Appl. Nano Mater. 2022;5:6736–6749. doi: 10.1021/acsanm.2c00760. [DOI] [Google Scholar]
  18. Fu H., Pan C., Yao W., Zhu Y.. Visible-Light-Induced Degradation of Rhodamine B by Nanosized Bi2WO6 . J. Phys. Chem. B. 2005;109:22432–22439. doi: 10.1021/jp052995j. [DOI] [PubMed] [Google Scholar]
  19. Lv Y., Yao W., Zong R., Zhu Y.. Fabrication of Wide–Range–Visible Photocatalyst Bi2WO6–x nanoplates via Surface Oxygen Vacancies. Sci. Rep. 2016;6:19347. doi: 10.1038/srep19347. [DOI] [PMC free article] [PubMed] [Google Scholar]
  20. Dou X., Li Q., Shi H.. Ag Nanoparticle-Decorated 2D/2D S-Scheme g-C3N4/Bi2WO6 Heterostructures for Efficient Photocatalytic Degradation of Tetracycline. CrystEngComm. 2021;23:4638–4647. doi: 10.1039/D1CE00439E. [DOI] [Google Scholar]
  21. Atla R., Oh T. H.. Novel Fabrication of the Recyclable MoS2/ Bi2WO6 Heterostructure and Its Effective Photocatalytic Degradation of Tetracycline under Visible Light Irradiation. Chemosphere. 2022;303:134922. doi: 10.1016/j.chemosphere.2022.134922. [DOI] [PubMed] [Google Scholar]
  22. Wang L., Wang W., Chen Y., Yao L., Zhao X., Shi H., Cao M., Liang Y.. Heterogeneous p–n Junction CdS/Cu2O Nanorod Arrays: Synthesis and Superior Visible-Light-Driven Photoelectrochemical Performance for Hydrogen Evolution. ACS Appl. Mater. Interfaces. 2018;10:11652–11662. doi: 10.1021/acsami.7b19530. [DOI] [PubMed] [Google Scholar]
  23. Lai C., Zhang M., Li B., Huang D., Zeng G., Qin L., Li X., Yi H., Cheng M., Li L., Chen Z.. Fabrication of CuS/BiVO4 (040) Binary Heterojunction Photocatalysts with Enhanced Photocatalytic Activity for Ciprofloxacin Degradation and Mechanism Insight. Chem. Eng. J. 2019;358:891–902. doi: 10.1016/j.cej.2018.10.072. [DOI] [Google Scholar]
  24. Lv Y. R., He R. K., Chen Z. Y., Li X., Xu Y. H.. Fabrication of Hierarchical Copper Sulfide/Bismuth Tungstate p–n Heterojunction with Two-Dimensional (2D) Interfacial Coupling for Enhanced Visible-Light Photocatalytic Degradation of Glyphosate. J. Colloid Interface Sci. 2020;560:293–302. doi: 10.1016/j.jcis.2019.10.064. [DOI] [PubMed] [Google Scholar]
  25. Tada H., Mitsui T., Kiyonaga T., Akita T., Tanaka K.. All-Solid-State Z-Scheme in CdS–Au–TiO2 Three-Component Nanojunction System. Nat. Mater. 2006;5:782–786. doi: 10.1038/nmat1734. [DOI] [PubMed] [Google Scholar]
  26. Zhou P., Yu J., Jaroniec M.. All-Solid-State Z-Scheme Photocatalytic Systems. Adv. Mater. 2014;26:4920–4935. doi: 10.1002/adma.201400288. [DOI] [PubMed] [Google Scholar]
  27. Liu B., Jiang X., Jiang X., Ma Y., Zhang Z., Han W.. Z-Scheme Photocarrier Transfer Realized in Tungsten Oxide-Based Photocatalysts by Combining with Bismuth Vanadate Quantum Dots. Inorg. Chem. 2021;60:3057–3064. doi: 10.1021/acs.inorgchem.0c03342. [DOI] [PubMed] [Google Scholar]
  28. Huang H., Zhao J., Du Y., Zhou C., Zhang M., Wang Z., Weng Y., Long J., Hofkens J., Steele J. A.. et al. Direct Z-Scheme Heterojunction of Semicoherent FAPbBr3/ Bi2WO6 Interface for Photoredox Reaction with Large Driving Force. ACS Nano. 2020;14(12):16689–16697. doi: 10.1021/acsnano.0c03146. [DOI] [PubMed] [Google Scholar]
  29. Deng Y., Tang L., Zeng G., Wang J., Zhou Y., Wang J., Tang J., Liu Y., Peng B., Chen F.. Facile Fabrication of a Direct Z-Scheme Ag2CrO4/g-C3N4 Photocatalyst with Enhanced Visible Light Photocatalytic Activity. J. Mol. Catal. A: Chem. 2016;421:209–221. doi: 10.1016/j.molcata.2016.05.024. [DOI] [Google Scholar]
  30. Li H., Yu H., Quan X., Chen S., Zhang Y.. Uncovering the Key Role of the Fermi Level of the Electron Mediator in a Z-Scheme Photocatalyst by Detecting the Charge Transfer Process of WO3–Metal– g-C3N4 (Metal = Cu, Ag, Au) ACS Appl. Mater. Interfaces. 2016;8:2111–2119. doi: 10.1021/acsami.5b10613. [DOI] [PubMed] [Google Scholar]
  31. Kavinkumar V., Verma A., Masilamani S., Kumar S., Jothivenkatachalam K., Fu Y. P.. Investigation of the Structural, Optical and Crystallographic Properties of Bi2WO6/Ag Plasmonic Hybrids and Their Photocatalytic and Electron Transfer Characteristics. Dalton Trans. 2019;48:10235–10250. doi: 10.1039/C9DT01807G. [DOI] [PubMed] [Google Scholar]
  32. Zhu Z., Lu Z., Wang D., Tang X., Yan Y., Shi W., Wang Y., Gao N., Yao X., Dong H.. Construction of high-dispersed Ag/Fe3O4/g-C3N4 photocatalyst by selective photo-deposition and improved photocatalytic activity. Appl. Catal., B. 2016;182:115–122. doi: 10.1016/j.apcatb.2015.09.029. [DOI] [Google Scholar]
  33. Bao H., Zhang H., Zhou L., Fu H., Liu G., Li Y., Cai W.. Ultrathin and Isotropic Metal Sulfide Wrapping on Plasmonic Metal Nanoparticles for Surface Enhanced Raman Scattering-Based Detection of Trace Heavy-Metal Ions. ACS Appl. Mater. Interfaces. 2019;11(31):28145–28153. doi: 10.1021/acsami.9b05878. [DOI] [PubMed] [Google Scholar]
  34. Huang W., Liu N., Zhang X., Wu M., Tang L.. Metal–Organic Framework g-C3N4/MIL-53­(Fe) Heterojunctions with Enhanced Photocatalytic Activity for Cr­(VI) Reduction under Visible Light. Appl. Surf. Sci. 2017;425:107–116. doi: 10.1016/j.apsusc.2017.07.050. [DOI] [Google Scholar]
  35. Liu M., Xue X., Yu S., Wang X., Hu X., Tian H., Chen H., Zheng W.. Improving Photocatalytic Performance from Bi2WO6@MoS2/graphene Hybrids via Gradual Charge Transferred Pathway. Sci. Rep. 2017;7:3637. doi: 10.1038/s41598-017-03911-6. [DOI] [PMC free article] [PubMed] [Google Scholar]
  36. Shi R., Huang G., Lin J., Zhu Y.. Photocatalytic Activity Enhancement for Bi2WO6 by Fluorine Substitution. J. Phys. Chem. C. 2009;113:19633–19638. doi: 10.1021/jp906680e. [DOI] [Google Scholar]
  37. Zhong X., Wu W. T., Jie H. N., Tang W. Y., Chen D. Y., Ruan T., Bai H. P.. Degradation of Norfloxacin by Copper-Doped Bi2WO6-Induced Sulfate Radical-Based Visible-Light Fenton Reaction. RSC Adv. 2020;10:38024–38032. doi: 10.1039/D0RA07378D. [DOI] [PMC free article] [PubMed] [Google Scholar]
  38. Huang J., Tan G., Ren H., Yang W., Xu C., Zhao C., Xia A.. Photoelectric Activity of a Bi2O3/Bi2WO6 –xF2 x Heterojunction Prepared by a Simple One-Step Microwave Hydrothermal Method. ACS Appl. Mater. Interfaces. 2014;6:21041–21050. doi: 10.1021/am505817h. [DOI] [PubMed] [Google Scholar]
  39. Maczka M., Macalik L., Hermanowicz K., Kepiński L., Tomaszewski P.. Phonon Properties of Nanosized Bismuth Layered Ferroelectric MaterialBi2WO6 . J. Raman Spectrosc. 2010;41:1059–1066. doi: 10.1002/jrs.2526. [DOI] [Google Scholar]
  40. Xu X., Liu G., Zhao J., Wang B., Ji M., Shan N., Chen Z., Yang Z., Xia J., Li H.. Interfacial Synergy of Ag Nanoparticles and Ultrathin Bi2WO6 Nanosheets for Boosting Organic Pollutants Photodegradation. Inorg. Chem. Commun. 2023;155:111050. doi: 10.1016/j.inoche.2023.111050. [DOI] [Google Scholar]
  41. Katiyar A. K., Sinha A. K., Manna S., Aluguri R., Ray S. K.. Optical Photoresponse of CuS–n-Si Radial Heterojunction with Si Nanocone Arrays Fabricated by Chemical Etching. Phys. Chem. Chem. Phys. 2013;15:20887–20893. doi: 10.1039/c3cp53603c. [DOI] [PubMed] [Google Scholar]
  42. Hu T., Li H., Du N., Hou W.. Iron-Doped Bismuth Tungstate with an Excellent Photocatalytic Performance. ChemCatChem. 2018;10:3040–3048. doi: 10.1002/cctc.201701965. [DOI] [Google Scholar]
  43. Wang X., Zhou Y., Wang N., Zhang J., Zhu L.. Carbonate-Induced Enhancement of Phenols Degradation in CuS/Peroxymonosulfate System: A Clear Correlation between This Enhancement and Electronic Effects of Phenol Substituents. J. Environ. Sci. 2023;129:139–151. doi: 10.1016/j.jes.2022.09.018. [DOI] [PubMed] [Google Scholar]
  44. Mandal S., Ananthakrishnan R.. Double Effects of Interfacial Ag Nanoparticles in a ZnO Multipod@Ag@Bi2S3 Z-Scheme Photocatalytic Redox System: Concurrent Tuning and Improving Charge-Transfer Efficiency. Inorg. Chem. 2020;59:7681–7699. doi: 10.1021/acs.inorgchem.0c00666. [DOI] [PubMed] [Google Scholar]
  45. Yuan Q., Chen L., Xiong M., He J., Luo S. L., Au C. T., Yin S. F.. Cu2O/BiVO4 Heterostructures: Synthesis and Application in Simultaneous Photocatalytic Oxidation of Organic Dyes and Reduction of Cr­(VI) under Visible Light. Chem. Eng. J. 2014;255:394–402. doi: 10.1016/j.cej.2014.06.031. [DOI] [Google Scholar]
  46. Bhoi Y. P., Mishra B. G.. Photocatalytic Degradation of Alachlor Using Type-II CuS/BiFeO3 Heterojunctions as Novel Photocatalyst under Visible Light Irradiation. Chem. Eng. J. 2018;344:391–401. doi: 10.1016/j.cej.2018.03.094. [DOI] [Google Scholar]
  47. Gnayem H., Sasson Y.. Nanostructured 3D Sunflower-Like Bismuth-Doped BiOClxBr1–x Solid Solutions with Enhanced Visible-Light Photocatalytic Activity as a Remarkably Efficient Technology for Water Purification. J. Phys. Chem. C. 2015;119:19201–19209. doi: 10.1021/acs.jpcc.5b05217. [DOI] [Google Scholar]
  48. Rauf A., Sher Shah M. S. A., Choi G. H., Humayoun U. B., Yoon D. H., Bae J. W., Park J., Kim W.-J., Yoo P. J.. Facile Synthesis of Hierarchically Structured Bi2S3/Bi2WO6 Photocatalysts for Highly Efficient Reduction of Cr­(VI) ACS Sustainable Chem. Eng. 2015;3:2847–2855. doi: 10.1021/acssuschemeng.5b00783. [DOI] [Google Scholar]
  49. Kumar A., Ananthakrishnan R.. Strategic Design of a WO3/PdOx–Carbon Shell Composite Photocatalyst: Visible-Light-Mediated Selective Hydrogenation of 5-Hydroxymethylfurfural. ACS Appl. Energy Mater. 2022;5:2706–2719. doi: 10.1021/acsaem.1c03065. [DOI] [Google Scholar]
  50. Kong X. Y., Choo Y. Y., Chai S.-P., Soh A. K., Mohamed A. R.. Oxygen Vacancy Induced Bi2WO6 for the Realization of Photocatalytic CO2 Reduction over the Full Solar Spectrum: From the UV to the NIR Region. Chem. Commun. 2016;52:14242–14245. doi: 10.1039/C6CC07750A. [DOI] [PubMed] [Google Scholar]
  51. Hu Y., Yu B., Ramadoss M., Li W., Yang D., Wang B., Chen Y.. Scalable Synthesis of Heterogeneous W–W2C Nanoparticle-Embedded CNT Networks for Boosted Hydrogen Evolution Reaction in Both Acidic and Alkaline Media. ACS Sustainable Chem. Eng. 2019;7:10016–10024. doi: 10.1021/acssuschemeng.9b01199. [DOI] [Google Scholar]
  52. Xu X., Meng L., Li Y., Sun C., Yang S., He H.. Bi2S3 Nanoribbons-Hybridized {001} Facets Exposed Bi2WO6 Ultrathin Nanosheets with Enhanced Visible-Light Photocatalytic Activity. Appl. Surf. Sci. 2019;479:410–422. doi: 10.1016/j.apsusc.2019.02.086. [DOI] [Google Scholar]
  53. Shi Z., Chen Z., Zhang Y., Wang X., Lu T., Wang Q., Zhang Z., Zhang P.. COF TzDa/Ag/AgBr Z-scheme heterojunction photocatalyst for efficient visible light driven elimination of antibiotics tetracycline and heavy metal ion Cr­(VI) Sep. Purif. Technol. 2022;288:120717. doi: 10.1016/j.seppur.2022.120717. [DOI] [Google Scholar]
  54. Majhi D., Mishra A. K., Das K., Bariki R., Mishra B. G.. Plasmonic Ag Nanoparticle Decorated Bi2O3/CuBi2O4 Photocatalyst for Expeditious Degradation of 17α-Ethinylestradiol and Cr­(VI) Reduction: Insight into Electron Transfer Mechanism and Enhanced Photocatalytic Activity. Chem. Eng. J. 2021;413:127506. doi: 10.1016/j.cej.2020.127506. [DOI] [Google Scholar]
  55. Bhoi Y. P., Behera C., Majhi D., Equeenuddin S. M., Mishra B. G.. Visible-Light-Assisted Photocatalytic Mineralization of Diuron Pesticide Using Novel Type-II CuS/Bi2W2O9 Heterojunctions with a Hierarchical Microspherical Structure. New J. Chem. 2018;42:281–292. doi: 10.1039/C7NJ03390G. [DOI] [Google Scholar]
  56. Jin C., Li W., Chen Y., Li R., Huo J., He Q., Wang Y.. Efficient Photocatalytic Degradation and Adsorption of Tetracycline over Type-II Heterojunctions Consisting of ZnO Nanorods and K-Doped Exfoliated g-C3N4 Nanosheets. Ind. Eng. Chem. Res. 2020;59:2860–2873. doi: 10.1021/acs.iecr.9b06911. [DOI] [Google Scholar]
  57. Yang S. F., Niu C. G., Huang D. W., Zhang H., Liang C., Zeng G. M.. SrTiO3 Nanocubes Decorated with Ag/AgCl Nanoparticles as Photocatalysts with Enhanced Visible-Light Photocatalytic Activity toward the Degradation of Dyes, Phenol, and Bisphenol A. Environ. Sci.: Nano. 2017;4:585–595. doi: 10.1039/C6EN00597G. [DOI] [Google Scholar]
  58. Xiao P., Shen C., Li Y., Cui S., Chen S., Yang J.. A One-Pot Hydrothermal Synthesis of Bi/Bi2O2CO3/Bi2WO6 Catalyst with Enhanced Photocatalytic Activity toward Tetracycline. J. Taiwan Inst. Chem. Eng. 2024;162:105611. doi: 10.1016/j.jtice.2024.105611. [DOI] [Google Scholar]
  59. Singh A., Srivastava B., Srivastava S. K., Bhatnagar A. K., Gupta A. K.. Quasi-1D/3D Bi2O4/phase-tuned C3N5 type-II heterostructure for the visible-light-driven photocatalytic degradation of resorcinol in wastewater: insights into the inhibitory effects of matrix interferences and phytotoxicity assessment. RSC Appl. Interfaces. 2026;3:510–526. doi: 10.1039/D5LF00338E. [DOI] [Google Scholar]
  60. Ding S., Gan W., Guo J., Chen R., Liu R., Zhao Z., Li J., Zhang M., Sun Z.. Construction of a SnS2/TiO2 S-Scheme Heterostructure Photocatalyst for Highly Efficient Photocatalytic Degradation of Tetracycline Hydrochloride. J. Mater. Chem. C. 2024;12(19):7079–7094. doi: 10.1039/D4TC00972J. [DOI] [Google Scholar]
  61. Wang H., Liao B., Lu T., Ai Y., Liu G.. Enhanced Visible-Light Photocatalytic Degradation of Tetracycline by Novel Hollow BiOCl@CeO2 Heterostructured Microspheres: Structural Characterization and Reaction Mechanism. J. Hazard. Mater. 2020;385:121552. doi: 10.1016/j.jhazmat.2019.121552. [DOI] [PubMed] [Google Scholar]
  62. Qiu Y., Lu J., Yan Y., Niu J.. Enhanced Visible-Light-Driven Photocatalytic Degradation of Tetracycline by 16% Er3+ −Bi2WO6 Photocatalyst. J. Hazard. Mater. 2022;422:126920. doi: 10.1016/j.jhazmat.2021.126920. [DOI] [PubMed] [Google Scholar]
  63. Chen S., Li B., Huang D., Xu P., Chen Y., Lei L., Wang Z., Deng R., Du L., Wang G.. Jointed Synchronous Photocatalytic Oxidation and Chromate Reduction Enabled by the Defect Distribution upon BiVO4: Mechanism Insight and Toxicity Assessment. ACS Appl. Mater. Interfaces. 2021;13(15):17586–17598. doi: 10.1021/acsami.1c01998. [DOI] [PubMed] [Google Scholar]
  64. Li M., Lai C., Yi H., Huang D., Qin L., Liu X., Li B.. et al. Multiple Charge-Carrier Transfer Channels of Z-Scheme Bismuth Tungstate-Based Photocatalyst for Tetracycline Degradation: Transformation Pathways and Mechanism. J. Colloid Interface Sci. 2019;555:770–782. doi: 10.1016/j.jcis.2019.08.035. [DOI] [PubMed] [Google Scholar]
  65. Yang R., Zhu Z., Hu C., Zhong S., Zhang L., Liu B., Wang W.. One-Step Preparation of (3D/2D/2D) BiVO4/FeVO4@rGO Heterojunction Composite Photocatalyst for the Removal of Tetracycline and Hexavalent Chromium Ions in Water. Chem. Eng. J. 2020;390:124522. doi: 10.1016/j.cej.2020.124522. [DOI] [Google Scholar]
  66. Choudhury S., Pattnayak S., Sahoo U., Aparajita P., Hota G.. S-Doped rGO-Enwrapped Magnetically Porous NiFe2O4/CuS Heterojunction: An Efficient Z-Scheme Nanophotocatalyst for Visible-Light-Driven Tetracycline Degradation and 4-Nitrophenol Reduction. Ind. Eng. Chem. Res. 2023;62:8191–8209. doi: 10.1021/acs.iecr.3c00213. [DOI] [Google Scholar]
  67. He J., Hu J., Hu Y., Guo S., Huang Q., Li Y., Zhou G., Gui T., Hu N., Chen X.. Hierarchical S-Scheme Heterostructure of CdIn2S4@UiO-66-NH2 toward Synchronously Boosting Photocatalytic Removal of Cr­(VI) and Tetracycline. Inorg. Chem. 2022;61(49):19961–19973. doi: 10.1021/acs.inorgchem.2c03240. [DOI] [PubMed] [Google Scholar]
  68. Liu C., Li Y., Cui X., Liang C., Xing G., Duan Q.. Construction of a Recyclable Dual-Responsive TiO2-Based Photocatalyst Modified with ZnIn2S4 Nanosheets and Zinc Phthalocyanine for Cr­(VI) Reduction under Visible Light. Chem. Eng. J. 2021;417:129332. doi: 10.1016/j.cej.2021.129332. [DOI] [Google Scholar]
  69. Li M., Song C., Wu Y., Wang M., Pan Z., Sun Y., Meng L., Han S., Xu L., Gan L.. Novel Z-Scheme Visible-Light Photocatalyst Based on CoFe2O4/BiOBr/Graphene Composites for Organic Dye Degradation and Cr­(VI) Reduction. Appl. Surf. Sci. 2019;478:744–753. doi: 10.1016/j.apsusc.2019.02.017. [DOI] [Google Scholar]
  70. Zhou H., Wen Z., Liu J., Ke J., Duan X., Wang S.. Z-Scheme Plasmonic Ag-Decorated WO3/Bi2WO6 Hybrids for Enhanced Photocatalytic Abatement of Chlorinated VOCs under Solar Light Irradiation. Appl. Catal., B. 2019;242:76–84. doi: 10.1016/j.apcatb.2018.09.090. [DOI] [Google Scholar]
  71. Ghosh S., Bera S., Singh A., Basu S., Basu R. N.. Hierarchical Bi2WO6/BiFeWO6 n–n Heterojunction as an Efficient Photocatalyst for Water Splitting under Visible Light. J. Alloys Compd. 2022;919:165700. doi: 10.1016/j.jallcom.2022.165700. [DOI] [Google Scholar]
  72. Zhou S., Zhang C., Xia L., Fu Z., Zhu N., Gong J., Wang X., Lyu P., Li L., Xu W.. A Flexible and Weavable Lignocellulose-Based Photocatalyst Supported by Natural Three-Dimensional Porous Juncus effusus for Highly Efficient Degradation of Environmental Contaminants. ACS Appl. Mater. Interfaces. 2022;14(24):27955–27967. doi: 10.1021/acsami.2c06207. [DOI] [PubMed] [Google Scholar]
  73. Xue J., Li Q., Sun S., Feng S., Jian H., Li Z., Shen Q., Yan Y.. All-Organic S-Scheme Carbon Nitride/Perylene Imide Heterojunction with π–π Stacking Modulates the PCET Process for CO2 Photoreduction. J. Mater. Sci. Technol. 2025;255:181–193. doi: 10.1016/j.jmst.2025.08.026. [DOI] [Google Scholar]
  74. Song X. -Y., Chen Q. -L.. Facile preparation of g-C3N4/Bi2WO6 hybrid photocatalyst with enhanced visible light photoreduction of Cr­(VI) J. Nanopart. Res. 2019;21:183. doi: 10.1007/s11051-019-4632-0. [DOI] [Google Scholar]

Associated Data

This section collects any data citations, data availability statements, or supplementary materials included in this article.

Supplementary Materials

ao6c05796_si_001.pdf (2.3MB, pdf)

Articles from ACS Omega are provided here courtesy of American Chemical Society

RESOURCES