Skip to main content
Analytical Science Advances logoLink to Analytical Science Advances
. 2026 Nov 7;7(2):e70116. doi: 10.1002/ansa.70116

Multi‐Analytical Characterization and Taxonomic Distinction of Australian Plant Exudates

Sophia A Vogelsang 1,2,✉, Oscar Paredes‐Mellone 3, Rafaella Georgiou 4,5, S Minhal Gardezi 5, Jo McDonald 6, Dimosthenis Sokaras 3, Rachel S Popelka‐Filcoff 2,✉, Uwe Bergmann 5,✉
PMCID: PMC13744402  PMID: 42999719

ABSTRACT

Plant exudates have been used worldwide for millennia in broad applications due to their unique physicochemical properties. Indigenous Australians have used exudates in long‐standing cultural and technical practices, including hafting adhesives and paint binders. Chemical characterization and botanical identification can provide important insight into the origin, properties, and usage of exudate materials from the archaeological past to the present. However, Australian exudates and cultural heritage materials have been far less examined compared to European, Asian, and North African counterparts. Here, we report combined Fourier transform infrared (FTIR) spectroscopy, X‐ray Raman scattering (XRS) spectroscopy, nuclear magnetic resonance (NMR) spectroscopy, and pyrolysis gas chromatography mass spectrometry (py‐GC‐MS) analyses for atomic‐ to molecular‐level characterization of over 20 genera of Australian exudates. This research contributes to fundamental understanding of the chemistry of exudates that drives their usage as natural binders. Integration of all four techniques and multivariate statistics reveals chemical differences at both the genus and species level. We establish correlations between taxonomic groupings and chemical composition to identify key features for distinction of exudates. Our multi‐analytical approach provides new insight into the unique chemistry of less well‐studied Australian exudates, with impact on the characterization of exudates in important cultural and archaeological materials worldwide.

Keywords: archaeological science, cultural heritage, exudate, infrared spectroscopy, mass spectrometry, nuclear magnetic resonance spectroscopy, X‐ray Raman scattering


The distinct physicochemical properties of plant exudates have led to millennia of use as medicines, food additives, and adhesives. Chemical analysis of exudates sheds new light on past technologies, artifact origins, and molecular structure‐function relations. Here, we report multi‐modal molecular characterization of twenty Australian exudate genera and taxonomic distinctions for their identification in cultural heritage and archaeology.

graphic file with name ANSA-7-e70116-g002.webp

1. Introduction

Plant exudates possess exceptional physicochemical properties that have shaped their usage as medicines, food additives, and adhesives over generations and across the globe [1, 2, 3]. Exudates are complex mixtures of large, heterogeneous organic molecules resulting in distinct chemistry that is both interesting and challenging to characterize. They can be divided into chemical classifications, including terpenoids (resins), polysaccharides (gums), and polyphenolics (sometimes referred to as kinos). Molecular‐level characterization of plant exudates in cultural and archaeological materials can provide valuable information complementing historic records and cultural knowledge. Chemical analysis can determine the botanical origin and composition of an exudate material to aid in the provenance of an artifact or tracing of past exchange networks. Connecting chemical information with Indigenous knowledge reveals new insight into the uses of exudates from the archaeological past to the present and into the development of traditions and technologies [4]. Furthermore, determination of the molecular structures that define the distinct material properties of exudates furthers our understanding of their structure‐function relations across past and future applications.

The Australian continent is home to over 20,000 unique native plant species. Aboriginal Australians have utilized plant exudates from a range of these distinct plant genera in traditions stretching over 65,000 years from the archaeological past to the present [5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17]. Plant exudates are used for intertwined practical and cultural purposes, as food sources, medicines, tools, and adhesives, while holding symbolic significance central to Dreaming, Country, and the cultural landscape [5]. These practices continue into the present day, and some contemporary Indigenous artists choose traditional binders over synthetic alternatives to connect their artwork with culture and Country [10]. Plant exudates are sought for their availability, physicochemical properties, and suitability for different applications. Key examples include exudates from spinifex (Triodia) and grass trees (Xanthorrhoea), which would be heated and sometimes mixed with dung, ash, or plant fibers for use as hafting adhesives for stone tools [5, 6, 7, 8, 13, 16, 17], paint binders [10, 12, 15], and varnishes [9]. While many Australian exudate species are botanically and chemically unique (e.g., Xanthorrhoea, Eucalyptus, and Triodia), many others possess chemical similarities to exudate species worldwide. Australian Callitris, Araucaria, and Wollemia resins exhibit similarity to sandarac resin (Tetraclinis articulata) from northern Africa, colophony (Pinus species) from Mediterranean pine trees, and Manila copal (Agathis dammara) from the Philippines, all used in global artistic traditions [18]. Gums from the thousands of species of Acacia native to Australia are closely related to Gum Arabic (Senegalia senegal, formerly Acacia senegal) [19].

Despite millennia of Indigenous traditions and technologies developed around the distinct physicochemical properties of Australian exudate species, few studies have focused on chemically characterizing exudates in Indigenous Australian cultural or archaeological materials [12, 13, 14, 15, 16, 20, 21]. Previous research has employed traditional laboratory methods to characterize Australian exudates, including gas chromatography mass spectrometry (GC‐MS) [14, 15, 16, 20], infrared (IR) spectroscopy [12, 16, 20, 21], optical and physical properties [13, 22], and nuclear magnetic resonance (NMR) spectroscopy [23]. IR spectroscopy reveals functional groups that differ across exudate types, enabling identification of probable binders in knives from the South Australian Museum [12] and examination of species‐level chemical variations [21]. Numerous studies by Lambert et al. have shown the ability of solid‐state 13C NMR and solution‐state 1H and 1H‐1H correlation spectroscopy (COSY) to discriminate exudates on the family and genus level [24, 25]. including Australian Eucalyptus kinos [23]. Pyrolysis GC‐MS (py‐GC‐MS) has been used by Reeves et al. to chemically distinguish Australian and European binders [15], and Bradshaw et al. characterized six ethnographic resins with GC‐MS, resulting in the identification of Xanthorrhoea, Canarium, and Triodia residues [14]. However, prior research has been limited by data sets representing few Australian exudate genera used in cultural heritage and other applications [12, 15, 20], distinction of taxa without identification of major molecular components [13, 16], and focus on a single analytical method [14, 15, 23]. Employment of a multi‐modal approach can help overcome the inherent limitations of individual techniques for robust chemical characterization alongside taxonomic differentiation. Recently, Georgiou et al. demonstrated a multi‐analytical approach using X‐ray Raman scattering (XRS) spectroscopy as a complement to Fourier transform IR spectroscopy (FTIR) and GC‐MS analyses to characterize century‐old Acacia, Callitris, Xanthorrhoea, and Eucalyptus exudates at the atomic, molecular, and functional group levels, but this study was limited to 10 exudates from four genera [20].

Here, we integrate synchrotron‐based XRS with laboratory‐based attenuated total reflectance (ATR)‐FTIR, NMR, and py‐GC‐MS for the first comprehensive chemical characterization and distinction of more than 50 Australian exudates. The analyzed exudates represent culturally important genera present in artworks, artifacts, and ethnographic collections, with the species illustrated in Figure 1. This study provides molecular‐level insight into the unique chemistry of Australian exudate species, their function, and essential identification in cultural heritage and archaeological contexts. XRS is an element‐specific, hard X‐ray energy‐loss technique that provides similar information to X‐ray absorption spectroscopy (XAS) [26, 27]. Because it uses penetrating hard X‐rays, XRS allows for bulk measurements without specific sample treatment or environment, an important advantage for precious and aged cultural‐heritage materials [20, 28, 29, 30]. XRS characterizes the local carbon bonding environment, FTIR enables determination of functional groups, py‐GC‐MS reveals chemical composition, and the addition of NMR informs on molecular structure and connectivity, which is inaccessible with the other methods. The advantages and constraints of each technique are evaluated alongside their ability to distinguish taxa for cultural heritage and archaeological applications, including Australian exudates and chemically similar organic binders used worldwide. Integration of complementary analytical techniques with multivariate analyses enables identification of key spectral and chemical features that discriminate exudate classes (polysaccharides, terpenoids, polyphenolics) and exudates of different botanical origin. This research will lead to a deeper understanding of millennia of Indigenous Australian usage of the exceptional physicochemical properties of plant exudates, and, more generally, of past technologies and artifact origins.

FIGURE 1.

FIGURE 1

Phylogenic tree of samples labeled with their experimentally determined chemical classifications. Most of the analyzed exudate samples are from a century‐old historic collection, and these were supplemented with modern samples from research partners for a handful of genera and species not represented (Triodia, Lechenaultia, and Corymbia). Full sample lists are in the appendix.

2. Experimental

2.1. Samples

A set of Australian plant exudates from over 20 plant genera was examined. The majority of samples were from a historical collection gathered across Australia, held in the South Australia state forensic laboratory (Forensic Sciences South Australia‐FSSA), moved to Flinders University, and now housed at the Archaeological Science Laboratory at the University of Melbourne. Although the collectors are unknown and original data notebooks no longer exist, each amber sample jar is clearly labeled with genus, species, collection location, and date. Many of the samples are over 100 years old. The amber glass bottles have been kept under ambient conditions. Recent studies have chemically examined subsets of samples from this collection [20, 21]. Additional modern samples were analyzed to supplement the historic collection. A subset of these samples was examined in a prior study on hafted‐tool use of Australian exudates [31]. Full sample lists are included in the appendix (Tables S1 and S2).

2.2. ATR‐Fourier Transform IR Spectroscopy

Each sample was screened with FTIR before additional measurements with other techniques. FTIR measurements were taken using a Tensor 27 FTIR spectrometer with a Pike ZnSe/Diamond ATR crystal attachment. Samples were prepared by grinding the material to a fine powder in an agate mortar and pestle. The powdered material was placed on the ATR crystal, ensuring the full crystal surface was covered. Consistent pressure was applied to each sample using the high‐pressure clamp. The instrument was purged with N2 gas to minimize signal from atmospheric water vapor and carbon dioxide. Spectra were acquired from 4000‐650 cm−1 with 128 scans and a resolution of 2 cm−1. Fresh background scans were collected before every sample measurement to minimize variations from atmospheric changes. Each spectrum was preprocessed using the rubber‐band baseline correction in the OPUS software to reduce sloping effects. Min‐max normalization was then applied to reduce effects of scattering and variation in sample thickness. FTIR peak assignments were based on reference handbooks [32, 33, 34] as well as prior studies, including Georgiou et al. [20] and Mann et al. [21].

2.3. XRS Spectroscopy

X‐ray Raman measurements (carbon K‐edge) were collected using the high‐resolution XRS spectrometer operated at beamline 15‐2 at the Stanford Synchrotron Radiation Laboratory (SSRL) [35]. The end station is equipped with a multi‐crystal Johann‐type spectrometer with 40 spherically bent and diced Si(110) crystals arranged on intersecting Rowland circles of 1 m diameter. The crystal analyzers are positioned at a fixed Bragg angle of 88° generating a fixed detection energy of 6.462 keV and a mean energy resolution of 0.307 eV when operated in the (440) order with the Si(311) monochromator. An inverse scanning approach is used to obtain the spectra, in which the incident energy is scanned through the Si(311) monochromator while the detection energy is held constant at 6.462 keV. The samples were measured in a grazing geometry (∼6°) to project the footprint of the beam horizontally to minimize radiation damage. Multiple spectra were collected on different sample regions, so that each scan probed a fresh spot, distributing radiation dose to reduce beam damage. Averaging scans collected over multiple spots ensured sufficient signal‐to‐noise ratio. A detailed description of the XRS data processing, radiation damage mitigation, and spectral decomposition is included in the appendix.

2.4. NMR Spectroscopy

To prepare samples for solution‐state NMR, approximately 14 mg of sample was dissolved in 1000 µL of solvent in a glass vial and sonicated for 3–4 h. Samples were left to sit overnight, and the supernatant was transferred into a 5 mm NMR tube the following day for measurement. 1H and 1H‐13C Heteronuclear Single Quantum Coherence (HSQC) NMR data were collected for all samples. Due to differences in solubility, resins and Xanthorrhoea were dissolved in chloroform (CDCl3, 99.8 atom % D with 0.03% tetramethylsilane [TMS], Sigma‐Aldrich), gums in D2O (99.9 atom % D, Sigma‐Aldrich), and kinos in dimethyl sulfoxide (d6‐DMSO, 99.8 atom % D with 0.03% TMS, Thermo Scientific Chemicals), with some measurements attempted in multiple solvents. Solution‐state 1H and 13C spectroscopic data were recorded on a 600 MHz Bruker Avance spectrometer with a TCI‐F cryoprobe at room temperature without spinning. 1D 1H parameters were as follows: delay time 1.0 s, acquisition time 4.96 s, and 8 scans. 2D 1H‐13C HSQC parameters were as follows: delay time 2.0 s, scan number 4, TD1 of 512, and TD2 of 4096. All spectra measured in CDCl3 and d6‐DMSO were referenced to TMS at δ 0 ppm. Spectra measured in D2O were referenced to trimethylsilylpropanoic acid at δ 0 ppm.

2.5. py‐GC‐MS Analyses

Sample preparation of plant exudates for py‐GC‐MS measurements followed the method developed by Reeves et al. [15] and used in Georgiou et al. [20]. Approximately 100–200 µg of exudate material was placed into a quartz capillary vial packed with a small amount of quartz wool. Tetramethylammonium hydroxide (2 µL, 25% wt methanol, Sigma‐Aldrich) was added to each sample using a GC syringe. Samples were then loaded onto the autosampler for analysis. Measurements were taken with a hyphenated pyrolysis gas chromatograph mass spectrometer (CDS 6150 pyrolyzer; Agilent 7890 GC 5975 MS). Samples were pyrolyzed at 600°C or 700°C for 1 min. For resins, the pyrolysis temperature was 600°C, and for polyphenolic exudates 700°C. The interface, valve oven, and GC transfer line were all set at 300°C. The GC was equipped with an HP‐5MS column. Its inlet was set at 300°C with a split ratio of 50:1 and a solvent delay of 4 min. The GC oven temperature profile was as follows: 50°C held for 5 min, then ramped to 240°C at 5°C/min and held for 5 min, then ramped to 300°C at 5°C/min and held for 8 min. The MS used an electron impact ion source and scanned a range of 30–350 m/z with quad temperature at 150°C and MS source temperature at 230°C. Establishing polysaccharide composition from the pyrogram of gums is not straightforward [20, 36, 37], so py‐GC‐MS was only collected for a select subset of polyphenolic and resin samples.

2.6. Statistical Analyses

Principal component analysis (PCA) and hierarchical clustering analysis (HCA) were conducted in Python with Scikit‐learn [38] using the PCA and AgglomerativeClustering functions. HCA was performed on the datasets using Euclidean distance as the metric and Ward linkage as the clustering method. PCA was performed on the datasets with centered singular value decomposition (SVD). Since py‐GC‐MS analyses were not conducted on gums, statistical analyses focused on XRS, FTIR, and NMR data for which data were collected on gums, resins, and polyphenolics. For the XRS data, analyses were conducted on the integrated areas of the first seven fitted Gaussian peaks from the spectral decomposition listed in the appendix (Table S4). For the FTIR data and 1H NMR data, analyses were conducted on the normalized intensity of selected peaks listed in the appendix (Tables S12 and S13). Ranges were used for features that are chemically related but exhibit small shifts in position across samples. The maximum intensity in each range was selected. Prior to application of PCA/HCA, the arrays of peak intensities/areas were standardized to ensure features in combined datasets were placed on the same scale. Standardization was performed using StandardScaler from Scikit‐learn according to the formula:

z=x−μ/σ

where z is the standardized value, x is the original data value, µ is the population mean, and σ is the population standard deviation. For the analyses of the combined datasets, the data arrays were concatenated and then standardized.

3. Results and Discussion

3.1. Diagnostic Features of Gums, Resins, and Polyphenolic Exudates

Characteristic features of gums, resins, and polyphenolic exudates were determined through analysis of FTIR, XRS, NMR, and py‐GC‐MS results. XRS and ATR‐FTIR provide direct examination of the solid material, including insoluble, non‐volatile, and cross‐linked components. On the other hand, solution‐state NMR only probes soluble fractions, and py‐GC‐MS enables analysis of volatile fractions (inherently or following derivatization) as well as degradation products and monomers from the pyrolysis of polymeric and high molecular weight components. py‐GC‐MS was collected for a select subset of polyphenolic and resin samples, as establishing polysaccharide composition from the pyrogram of gums is not straightforward [20, 36, 37].

The main carbon species observed for gums, resins, and polyphenolic exudates are illustrated in Figure 2 through the XRS and FTIR spectra of nine representative Australian exudate species. FTIR assignments were based on handbooks [32, 33, 34] and studies cited therein. The spectral decomposition of the normalized background‐corrected XRS spectra is described in the appendix. Since XRS is an electronic structure probe, it provides semi‐quantitative carbon speciation of the bulk solid, which is not directly accessible by the other methods. Figure S10 illustrates the distinct carbon speciation of gums, resins, and polyphenolic exudates from XRS.

FIGURE 2.

FIGURE 2

Attenuated total reflectance‐Fourier transform infrared (ATR‐FTIR) and X‐ray Raman scattering (XRS) spectra of nine representative Australian exudates. (A) Araucaria cunninghamii, Canarium australasicum, and Triodia sp. represent the terpenoid resins; (B) Hakea macraeana, Brachychiton populneus, and Atalaya hemiglauca represent the polysaccharide gums; (C) Eucalyptus sideroxylon, Corymbia calophylla, and Xanthorrhoea australis represent polyphenolic exudates.

Resins are characterized by terpenic composition, including mono‐, sesqui‐, di‐, and tri‐terpenoids as well as polymeric fractions, which all contain carboxylic acids, alkenes, and CH3/CH2 groups as the major carbon species. In FTIR, the intense peak at 1690 cm−1 from C═O vibrations, accompanied by vibrations of alkanes from 2900 to 2800 cm−1, is diagnostic of resins (Figure 2A). In the XRS spectra, the resins are carboxyl‐rich, with a small peak at 285.4 eV from alkene content and large carboxylic acid content at 288.6–288.7 eV (Figure 2A and Figure S10). The 1H NMR spectra of resins are distinguished by intense, overlapped peaks from δ 0 to 3 from saturated hydrocarbons (Figure S11). The pyrograms of resins are dominated by the presence of monoterpenes, diterpenes, sesquiterpenes, and triterpenes (Figures S23 and S24).

Gums are characterized by polysaccharide composition dominated by acetal and alcohol content. The XRS spectra of gums are distinguished by weak or no peaks from 284–288 eV, then larger features at 288.8 and 289.6 eV from acetal and alcohol groups, respectively (Figure 2B and Figure S10). Large alcohol vibrations from 3600 to 3000 cm−1, an asymmetric peak at 1600 cm−1, and intense polysaccharide vibrations from 1100 to 900 cm−1 are diagnostic of gums in the IR spectra (Figure 2B). The 1H NMR spectra are characterized by peaks from δ 3 to 5.5 and few other peaks (Figure S20).

Polyphenolic exudates are dominated by aromatic and phenolic composition. The XRS spectra of polyphenolic exudates are aromatic‐rich, with intense peaks from 1s‐π* transitions of aromatic (285.5–285.6 eV) and phenolic (287.3–287.5 eV) carbon (Figure 2C and Figure S10). Large peaks at 1605, 1517, and 1443 cm−1 from vibrations of aromatic C = C groups differentiate the FTIR spectra (Figure 2C). The 1H NMR spectra are similarly dominated by peaks from aromatic content from δ 6 to 8 and a few peaks from δ 1 to 3 from saturated content (Figures S15 and S18). The pyrograms are characterized by pyrolysis products of polyphenolic components, such as flavanones, chalcones, and tannins (Figure S25).

3.2. Chemical Distinctions Across and Within Genera

Based on combined FTIR, XRS, NMR, and py‐GC‐MS data, we identified major functional groups, carbon bonding, and molecular structures distinguishing plant taxa on the family and genus level (Figure 3). Exudates can first be separated into chemical groups (terpenoid, polysaccharide, polyphenolic, or mixed/other composition) and then into taxonomic groups. ATR‐FTIR is well‐suited for initial screening as the sample can be recovered for further analysis. The identified list of features is not exhaustive but instead highlights select characteristics that provide a framework for distinguishing Australian exudates using spectral and chemical information.

FIGURE 3.

FIGURE 3

Summary of Fourier transform infrared (FTIR), X‐ray Raman scattering (XRS), nuclear magnetic resonance (NMR), and pyrolysis gas chromatography mass spectrometry (py‐GCMS) features that characterize gums, resins, and polyphenolic exudates and features that can be used to identify plant taxa within these groups. This schematic does not include the small subset of samples of other/mixed chemical classifications (Myoporum viscosum, Casuarina sp., Araucaria bidwillii, Lechenaultia divaricata, and Grevillea striata) for which more detailed chemical information that can be used for their distinction is provided in the appendix.

3.2.1. Terpenoid Resins

Eighteen samples in this study were classified as resins from Araucaria, Callitris, Canarium, Erythrophleum, Pinus, Triodia, Wollemia, and Acacia. In general, resins within the same genus exhibit similar chemical compositions, with the main constituents illustrated in Figure 4, identified by NMR and py‐GC‐MS through comparison with the Wiley275 mass spectral library and literature reports [20, 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50, 51, 52].

FIGURE 4.

FIGURE 4

Main structures of Callitris, Araucaria, Pinus, Wollemia, Canarium, Triodia, Eucalyptus, Angophora, Corymbia, Xanthorrhoea, and eudicot gums determined through pyrolysis gas chromatography mass spectrometry (py‐GC‐MS) and nuclear magnetic resonance (NMR) analyses and supported by literature reports. The conifer resins (a) are dominated by abietane, pimarane, and labdane diterpenes. Canarium resins (b) are composed of alpha‐ and beta‐amyrin. Triodia resins (c) are characterized by epeuric acid as well as long n‐alkanes and fatty acid methyl esters. Eucalyptus, Angophora, and Corymbia kinos (d) are composed of polyflavanoids as well as gallic acid (likely in the form of gallotannins) and flavanones. Xanthorrhoea exudates (e) are dominated by polyflavanoids, flavanones, chalcones, and free aromatic acids. Lastly, eudicot gums (f) are comprised of complex, branched heteropolysaccharides. Determination of the specific glycan structure and monomer units was beyond the scope of this study, and the illustrated structure is based upon mannose, rhamnose, glucuronic acid, xylose, and arabinose, sugars commonly found in gums.

The conifer resins, Araucaria, Callitris, Pinus, and Wollemia, are dominated by diterpenic resin acids with abietane, pimarane, and labdane‐type skeletons, including communic acid, iso‐communic acid, dehydroabietic acid, callitrisic (4‐epi‐dehydroabietic) acid, sandaracopimaric acid, pimaric acid, isopimaric acid, and isocupressic acid (Figure 4A). Their XRS spectra stand out with the highest ratios of alkene to aliphatic content based on the fitted Gaussian distribution integrated areas at 285.4 eV (alkene) and 287.7 eV (aliphatic). While the differences between conifer resins and Angiosperm resins (Canarium, Triodia, and Erythrophleum) are clear, distinguishing within the conifers is more difficult. In general, the conifer resins exhibit similar XRS and IR spectra, reflecting their similar carbon speciation (Figures S4, S7, and S10). NMR and py‐GC‐MS reveal molecular structures and diterpene content across the conifer resins, providing potential for genus‐level discrimination between Callitris, Araucaria, Pinus, and Wollemia (Figure 4A). For example, the Callitris resins are differentiated by dominant sandaracopimaric and callitrisic acid content. Further details on chemical distinctions within the conifers through NMR and py‐GC‐MS are provided in the appendix (Figures S11–S13 and S23).

The Canarium samples are distinguished by primarily triterpene and sesquiterpene content dominated by α‐amyrin and β‐amyrin detected via NMR and py‐GC‐MS (Figures S11 and S24). The relative amount of β‐amyrin appears higher in Canarium australasicum based on the areas of the 1H NMR peaks. Their XRS spectra exhibit a plateau from 287 to 290 eV compared to the sharp peak at 288.6–288.7 eV observed in the other resins, potentially due to lower carboxylic acid content, which is reflected in the weaker 1690 cm−1 C═O vibration in the FTIR spectra (Figures S6R,S and S7B,C).

Triodia is distinguished from the other resins by the presence of long saturated hydrocarbon chains and fatty acid methyl esters (FAMEs) unique to the genus and labdane diterpene content detected via py‐GC‐MS (Figure S24). The XRS spectrum has the lowest ratio of the alkene (285.4 eV) to aliphatic (287.7 eV) areas (≈1:4), which is consistent with the presence of highly saturated hydrocarbon chains and FAMEs (Figure S7A). Triodia (Spinifex) is a prominent and widely used exudate adhesive [8, 16, 31]; there are very sparse reports on the chemical composition [15, 53], and as far as the authors are aware, this is the first report of diterpene, saturated hydrocarbon, and FAME composition.

While the FTIR and XRS spectra for Erythrophleum present characteristic resin features from aliphatic, alkene, and carboxylic acid groups (Figures S6O,P and S7F,G), components in the pyrogram for Erythrophleum labonchorii had poor matches with available libraries and literature data (Figure S24). Although specific compounds could not be identified, the combined NMR and py‐GC‐MS results suggest a resin composition distinct from the other genera (Figures S11, S13C, and S24).

Interestingly, two Acacia samples, Acacia minyura and A. craspedocarpa, exhibited features characteristic of terpenoids in their FTIR spectra, 2900–2800 cm−1 (CH2/CH3 vibrations), 1690 cm−1 (C═O vibrations of carboxylic acids), 1644 cm−1 (conjugated C═C vibrations), and 1445 and 1380 cm−1 (CH2/CH3 deformations), and have thus been classified as resins (Figure S5R,S). The profiles of their XRS spectra also match those of other resins measured, which are dominated by resonances from aliphatic groups, alkenes, and carboxylic acids, the main carbon species in terpenoids (Figure S9B,C). Acacia is a very large genus with over 1000 species, the majority of which are native to Australia. Studies of the chemical composition of Acacia exudates typically report polysaccharide composition [20, 21, 54, 55]. To the best of our knowledge, the chemical composition of Acacia minyura and A. craspedocarpa and their classification as terpenoid resins have not been previously reported in the literature.

3.2.2. Polysaccharide Gums

Thirteen samples were classified as polysaccharide gums from Acacia, Alectryon, Atalaya, Avicennia, Brachychiton, Capparis, Sloanea, Flindersia, Grevillea, and Hakea. As there are only samples of one species from most of the polysaccharide genera examined, thorough assessment of intra‐genus chemistry is not possible. However, the sample set provides insight into the carbon chemistry of Australian gums and the ability of FTIR, XRS, and NMR to distinguish gums.

The FTIR spectra of the gums are very similar, with the exception of some variations in the fingerprint region for Hakea macraeana, Brachychiton populneus, and Flindersia australis (Figures S5 and S6). The XRS spectra exhibit small distinctions between gums in the presence of a small peak at 285.3–285.6 eV from the 1s‐π* transitions of aromatic or olefinic carbons in Hakea macraeana, Capparis anomala, Capparis mitchellii, Flindersia australis, and Atalaya hemiglauca (Figure S9). Subtle variation is also present in the relative heights of features from acetal (288.8 eV) and alcohol (289.6 eV) groups (Figure S10).

In the NMR spectra, the differences across samples are much more pronounced than those observed by IR and XRS, and the HSQC spectra provide further insight into glycan structures (Figures S20–S22). The HSQC spectra feature cross‐peaks in three main regions: δ 0.5–2.5/20–40 from aliphatic carbons, δ 3.5–4.5/60–90 from carbons in the sugar ring, and δ 4.5–5.5/100–115 from anomeric carbons. The high density of HSQC cross‐peaks for all gums measured suggests complex polysaccharide chains composed of many different sugar monomers. Notably, the three anomeric cross‐peaks observed for Brachychiton populneus are not seen in any other gums, suggesting a unique polysaccharide backbone (Figure S22). Across the gums measured in this study, the majority of anomeric cross‐peaks have carbon chemical shifts above δ 100, indicating involvement in glycoside linkages. The absence of features from ketones or aldehydes in the FTIR and XRS spectra, especially the diagnostic C═O vibration between 1700–1750 cm−1, also suggests that the sugars are engaged in glycoside linkages (Figures S5, S6, and S9).

An aliphatic cross‐peak at δ 1.3/16.6 observed in the majority of the gums (weak for Brachychiton populneus) indicates the presence of a shared 6‐deoxysugar, likely rhamnose (Figures S21 and S22). Sugar composition based on GC‐MS measurements of Acacia bakeri and additional Australian Acacia gums in Georgiou et al. confirms the presence of rhamnose, which has also been reported in Atalaya, Brachychiton, and Grevillea gums [20, 56, 57, 58]. Cross‐peaks from δ 80 to 85 were also observed for all genera except Brachychiton populneus and are diagnostic of furanose sugars, particularly C‐4 of aldofuranoses or C‐5 of ketofuranose units, such as galactose or arabinose (Figures S21 and S22). Both galactose and arabinose were found in Acacia bakeri [20] and have been reported in Atalaya, Brachychiton, Grevillea, and Hakea gums [56, 57, 58, 59].

While many individual cross‐peaks are shared between gums, the combination of cross‐peaks is unique for each sample measured, indicating distinct polysaccharide structures. Thus, 2D NMR offers a powerful complement to FTIR and XRS analyses for discrimination of polysaccharide gums of different taxa, with added insight into glycan structure and connectivity inaccessible with the other methods. For example, while Atalaya hemiglauca and Alectryon oleifolius present extremely similar FTIR (Figure S6) and XRS (Figure S9) spectra, there are clear differences in the HSQC spectra (Figure S22B,C), such as the anomeric cross‐peak at δ 5.1/104.5 present for Atalaya but not Alectryon.

3.2.3. Polyphenolic Exudates

Fourteen exudates were classified as polyphenolic from Angophora, Corymbia, Eucalyptus, and Xanthorrhoea. The samples are dominated by polyphenolic content, with the main molecular structures for each genus displayed in Figure 4, identified by NMR and py‐GC‐MS through comparison with the Wiley 275 mass spectral library and literature reports [20, 60, 61, 62].

Among the polyphenolic exudates, the Xanthorrhoea samples exhibit the highest aromatic/olefinic content with the largest peaks at 285.5 eV in the XRS spectra (Figure S8J–L). The Xanthorrhoea FTIR spectra are also distinguished by a strong peak at 832 cm−1 associated with = C‐H out‐of‐plane stretching (Figure S5L–O). Alkenes are present in the free aromatic acids and chalcones identified alongside flavonoids in the Xanthorrhoea pyrograms (Figure S25). The alkene and aromatic regions in the Xanthorrhoea NMR spectra are densely populated, suggesting a diverse array of structural fragments (Figures S18 and S19). The 1H NMR spectra of Xanthorrhoea are characterized by peaks at δ 12 from carboxylic acids, a series of sharp peaks within the aromatic region, intense C‐O peaks from δ 3.7 to 3.9, and saturated peaks from δ 1 to 3 consistent with descriptions of the genus by Lambert et al. [63].

Chemical variance is also observed among the Myrtaceae kinos from Eucalyptus, Angophora and Corymbia, although the FTIR spectra are quite similar. Corymbia and Angophora stand out with the presence of 1H NMR peaks from δ 12 to 12.5 arising from carboxylic acids or hydroxy groups with strong hydrogen bonding, such as the hydroxy groups of flavonoids, that are not present in Eucalyptus (Figure S15). The Angophora and Corymbia kinos also share HSQC cross‐peaks from naringenin (3,4’,5,7‐tetrahydoxyflavanone) and aromadendrin (5,7,4’‐trihydroxyflavanone) based on comparison with the literature (Figure S16) [60, 61, 64]. The Corymbia pyrograms support the presence of naringenin and aromadendrin through detection of potential pyrolysis products of 5,7‐dihydroxy flavonoids with mono‐substituted B‐rings, particularly methyl 4‐methoxybenzoate (Figure S25).

In contrast, the Eucalyptus samples exhibit a small number of HSQC cross‐peaks, with the exception of Eucalyptus microcarpa, which exhibits numerous cross‐peaks, including peaks from naringenin and aromadendrin (Figure S17). In the HSQC spectra for Eucalyptus largiflorens and phenax, there are only two aromatic cross‐peaks at δ 7.5/110.3 and δ 6.9/108.6, with the latter tentatively assigned to galloyl groups (Figure S17). These two HSQC cross‐peaks are observed for all of the Myrtaceae kinos with the exception of Eucalyptus microcarpa, which lacks the δ 7.5/110.3 cross‐peak. The fully methylated derivative of gallic acid is also detected in the pyrograms of all Myrtaceae kinos measured (Figure S25) and dominates the pyrograms of Eucalyptus largiflorens and phenax published by Georgiou et al. [20]. Galloyl groups are likely present in the kinos in the form of gallotannins, as reported by Georgiou et al. [20], or galloylated flavonoids, such as epigallocatechin‐3‐O‐gallate. Eucalyptus viminalis and sideroxylon exhibit additional HSQC cross‐peaks in the aromatic region which could be from flavonoids, such as condensed tannins, consistent with components detected in the pyrograms (Figures S17 and S25).

There is noticeable chemical variance within the Eucalyptus samples seen across all four techniques (Figures S5, S8, S15, and S16). FTIR measurements of more than 30 additional Eucalyptus samples, many of which were also measured by Mann et al. [21], emphasize the chemical variability of the kinos. The IR spectra of Eucalyptus sideroxylon, viminalis, phenax, microcarpa, and largiflorens represent many of the fingerprints observed for additional Eucalyptus species (Figure S5). The varied chemical profiles among the Eucalyptus samples could allow for distinction between certain species or groups of species. Eucalyptus species have different geographical sources within Australia, and establishing a link from chemical features to plant species to geographic regions could inform on the origins of unknown plant materials.

3.2.4. Other Exudates

While the majority of samples measured in this study are classified under gum, resin, or polyphenolic, a small subset of six samples were measured representing other chemical compositions. Araucaria bidwillii and Lechenaultia divaricata were identified as gum‐resins that contain a mixture of polysaccharide (gum) and terpenoid (resin) content. While the usage of Lechenaultia divaricata for hafted stone tools has been explored by Rots et al. [31], as far as the authors are aware, this is the first report on the molecular composition of Lechenaultia exudate and characterization of L. divaricata as a gum‐resin. Myoporum viscosum was identified as a manna‐exudate composed mostly of mannitol. Similarly, Acacia aneura exhibits sugar alcohol composition consistent with a manna‐exudate. Grevillea striata exhibited an aromatic, aliphatic, and alkene composition distinct from the other exudates, including Grevillea robusta, which exhibited polysaccharide chemistry. Although reports on Grevillea exudate chemistry are sparse, studies of Grevillea exudates, including G. striata, report polysaccharide composition, with the genus typically described as a gum [57, 65, 66]. Lastly, Casuarina sp. was the only sample measured to exhibit mixed phenolic and terpenoid content.

3.3. Taxonomic Discrimination Through Statistical Analyses

3.3.1. Hierarchical Clustering Analysis

HCA was applied to establish whether groupings based on carbon speciation of the bulk solid (measured by XRS and FTIR) were consistent with taxonomic divisions. HCA was selected as the clustering method as it does not necessitate a predetermined number or size of clusters and provides useful visualization of the entire dataset, with the dendrogram illustrating how similar/dissimilar samples and groups of samples are to each other. The HCA dendrogram from combined analysis of the XRS and FTIR datasets shows clear division of gums, resins, and polyphenolic exudates (Figure 5) as well as clusters of samples from the same taxa. For example, within the polyphenolic exudates, the Xanthorrhoea samples and Myrtales cluster together. Within the resins, the two Canarium samples cluster together, and there are two groupings of conifer resins. Trends among different gum‐producing genera are difficult to assess, since there was only one sample available per genus for the majority of gums, but the gums all cluster together. Overall, the dendrogram illustrates a strong connection between the chemical composition of the bulk solid and taxonomic groups, promising for the distinction and identification of unknown exudates.

FIGURE 5.

FIGURE 5

Dendrogram from hierarchical clustering analysis (HCA) of the combined FTIR and XRS datasets colored by taxonomic groupings.

3.3.2. Principal Component Analysis

PCA was then applied to the FTIR, XRS, and NMR data individually and together for dimensionality reduction to visualize the datasets and explore correlations between chemistry and taxonomic divisions across the techniques (Figure 6). PCA loadings were also used to evaluate how spectral and chemical features contribute to variation in each dataset and identify which features may be important for distinction of exudates (Figure S27; Tables S14 and S15).

FIGURE 6.

FIGURE 6

Principal component analysis (PCA) of Fourier transform infrared (FTIR), X‐ray Raman scattering (XRS), and 1H nuclear magnetic resonance (NMR) data. (A) Projection of the first two principal components from PCA applied to the normalized intensity of key peaks in the FTIR data. (B) Projection of the first two principal components from PCA applied to the spectral decomposition of the XRS data. (C) Projection of the first two principal components from PCA applied to the normalized intensity of key peaks in the 1H NMR data. (D) Projection of the first two principal components from PCA applied to the combined FTIR, XRS, and 1H NMR datasets. On each PCA plot, 95% confidence ellipses for polysaccharide, polyphenolic, and terpenoid exudates are indicated in gray.

For the FTIR data, vibrations at 890–880 and 1710–1690 cm−1 contribute the most to variation in PC1 with positive correlation, and 1040–1030 and 1030–1020 cm−1 with negative correlation. These features separate the resins from the kinos and gums, highlighting the intense carboxyl (1710–1690 cm−1) peak that is diagnostic of resins. For PC2, vibrations at 1520–1510, 1330–1310, 845–830, and 820–800 cm−1 contribute the most to the variation, all with positive correlation. There is a large separation between the Xanthorrhoea and Myrtaceae kinos in PC2. The Xanthorrhoea samples have a larger aromatic C═C peak at 1520–1510 cm−1 and sharp peaks from 845 to 830 and 820 to 800 cm−1 associated with = C‐H vibrations, distinguishing their spectra. The plot of PC1 and PC2 in Figure 6A shows clear distinction of certain genera, such as Xanthorrhoea and Canarium, but genus‐level distinctions within the conifer resins and Myrtaceae kinos are less apparent. The gums group tightly reflecting their very similar IR features, with the exception of Flindersia and Brachychiton.

In the PCA analyses of the XRS data, the peaks at 284.9–285.6 eV (aromatic/alkene) and 286.8–288.0 eV (phenolic/aliphatic) contribute the most to variations in PC1 with positive correlation. PC1 separates the polyphenolic exudates from the gums and resins, emphasizing the diagnostic 1s‐π* transitions of aromatic and phenolic carbon for polyphenolic exudates. For PC2, the peaks at 288.3–288.8 eV (carboxyl/acetal) and 289.0289.6 eV (alcohols) contribute the most to variation with positive and negative correlation, respectively. PC2 separates the resins from gums, and the carboxyl feature is characteristic of resins, while the gums possess large alcohol features. The plot of PC1 and PC2 for the XRS data in Figure 6B shows larger variation within the gums and Myrtaceae kinos compared to FTIR. In particular, groupings of Angophora, Corymbia, Eucalyptus, and Xanthorrhoea can be clearly observed.

For the 1H NMR data, peaks from δ 3.5 to 4.4 contribute the most to variation in PC1 with a positive correlation, which separates the gums from resins. Peaks from δ 3.5 to 4.5 are diagnostic of carbohydrates in 1H NMR spectra. In PC2, peaks at δ 2.7–2.8, 5.8–5.9, 6.9, 7.5, and 7.8–7.9 contribute the most to variation with positive correlation and separate the polyphenolic exudates from the gums and resins. The 1H NMR spectra of polyphenolic exudates are distinguished by large peaks from aromatic content at δ 6–8. The plot of PC1 and PC2 in Figure 6C displays large variation within the gums as well as clear differentiation between Xanthorrhoea and Corymbia and the other polyphenolic exudates. While the resins are more tightly clustered than the other exudates, there are genus‐level groupings, particularly the Callitris resins, which all cluster together.

PCA was also applied to the combined FTIR, XRS, and 1H NMR data (Figure 6D). In PC1, the IR features from 1020‐1030 and 1040‐1030 cm−1, associated with C‐O and polysaccharide skeletal vibrations, and NMR features from δ 3.7‐4.5, from C‐O and alkenes, contribute most to variance in the positive direction. IR features at 2946‐2914 cm−1, 1690–1710 cm−1 (C═O vibrations) and 880–890 cm−1, and NMR features at δ 0.8 and 1.1 contribute the most in the negative direction for PC1. In PC1, there is clear separation between gums and resins, as well as some within the gums and Myrtaceae kinos. For PC2, XRS features at 283.0–284.5, 284.9–285.6, 286.0–286.8, and 286.8–288.0 eV, NMR peaks at δ 2.8 and 6.9, and IR peaks at 1615–1595, 1520–1510, 1330–1310, 845–830, and 820–800 cm−1 contribute the most to variance in the positive direction, and the XRS peaks at 289.0–289.6 and 289.9–290.9 eV and the IR peak at 886 cm−1 contribute the most in the negative direction. PC2 separates the kinos from gums and resins and separates Xanthorrhoea from the Myrtaceae kinos. Overall, the combined analysis provides clear separation between chemical classes as well as genera and highlights important features across FTIR, XRS and NMR for distinction of plant exudates.

Analysis of PCA plots and loading factors, alongside inspection of spectra, informed compilation of key features for identification highlighted in Figure 3. The PCA results support the distinction of each exudate by chemical class and highlight the ability of FTIR, XRS, and 1H NMR to independently distinguish gums, resins, and polyphenolic exudates. The majority of samples of the same genera cluster in the same regions across all three techniques, illustrating their shared chemistry (with the exception of Grevillea striata, Araucaria bidwillii, Acacia minyura, and Acacia craspedocarpa). However, the datasets exhibit differences in the groupings of genera reflecting the different chemical features probed by each method and their ability to distinguish between taxa.

Within the resins, Angiosperm genera (Canarium, Erythrophelum, and Triodia) can be distinguished by FTIR, XRS, and NMR individually, but the conifer resins (Araucaria, Pinus, Callitris, and Wollemia) are more difficult to distinguish. Information on terpenoid composition and molecular structure provided by NMR and py‐GCMS is necessary to discern between conifer resins. While Xanthorrhoea is easily separated from other polyphenolic exudates by FTIR, XRS, and NMR individually, the distinction of Myrtaceae kinos (Eucalyptus, Corymbia, and Angophora) necessitates combined information due to their similar chemistry. Within the gums, XRS and 1H NMR provide better separation of different exudates than FTIR. Sugar monomers and polysaccharide chains contain similar functional groups, leading to strong similarities in the FTIR data across gums. NMR data is associated with molecular structures and connectivity, providing improved distinction between polysaccharide gums, and thus a larger spread in the PCA plots.

4. Conclusion

This study demonstrates robust chemical characterization of major functional groups, carbon bonding, and molecular structures for a diverse set of over 50 Australian plant exudates using a combination of XRS, FTIR, NMR, and py‐GC‐MS. We determined key features to differentiate gums, resins, and polyphenolic exudates as well as plant genera by combining chemical information from all four techniques. We show how the use of multivariate statistics to determine distinctions among plant exudates aids the interpretation and chemical classification of complex XRS, FTIR, and 1H NMR spectra. Although this study focused on genus‐level distinctions, we were able to identify chemical variations at the species level for select genera where samples from multiple species were available. While XRS, FTIR, NMR, and py‐GC‐MS are each independently capable of differentiating between polysaccharide, terpenoid, and polyphenolic exudates, the ability to distinguish taxa varies across methods and depends on the specific genus. Distinctions between genera within the conifer resins and Myrtaceae kinos are more challenging to assess with individual techniques but can be revealed by combining analytical methods. Here, solution‐state NMR provides promising distinction of gums through differences in glycan structure, which are not accessible with the other methods. However, the sample quantity required for NMR presents a limitation for widespread implementation in heritage contexts, as sampling milligram quantities is not possible for many historic materials.

Our study focused on untreated exudate samples, but the methods we employed are also suited to address the added complexities of characterizing cultural heritage samples that have been heated, mixed, or undergone other treatments. Comparing our results from century‐old samples with those of modern samples suggests that some characteristic chemical markers are preserved, making distinction of major chemical and taxonomic classes possible for aged exudates. This also indicates that modern reference samples are valuable for the analysis of exudate material in aged artifacts. However, further investigation of aging‐related chemical changes is needed to understand the full implications on material identification and preservation in aged artifacts. Our data from this historic collection, which represents naturally aged samples, provide a unique opportunity for further studies of the aging of exudates.

Finally, the data and methodology are applicable to plant exudates and natural binders with related chemistry used worldwide. Although exudate binders and adhesives may be overlooked as minor parts of many artifacts, their chemical composition and botanical origin can shed new light on past technologies. Combined with Indigenous knowledge, material identification can give valuable insight into provenance, exchange systems, material selection, and the cultural usage of natural binders across time.

5. Artificial Intelligence Disclosure Statement

The authors declare that no artificial intelligence tools were used in the writing, editing, data collection, analysis, or figure generation for this manuscript.

Author Contributions

Sophia A. Vogelsang: conceptualization, investigation, funding acquisition, writing – original draft, writing – review & editing, methodology, validation, visualization, and formal analysis. Oscar Paredes Mellone: methodology, resources, formal analysis, validation, and writing – review & editing. Rafaella Georgiou: investigation and conceptualization. S. Minhal Gardezi: investigation. Jo McDonald: writing – review & editing and funding acquisition. Dimosthenis Sokaras: conceptualization, validation, resources, and methodology. Rachel S. Popelka‐Filcoff: conceptualization, funding acquisition, writing – review & editing, methodology, project administration, supervision, and resources. Uwe Bergmann: conceptualization, funding acquisition, writing – review & editing, methodology, project administration, supervision, and resources.

Conflicts of Interest

The authors declare no conflicts of interest.

Funding

This material was supported by funding from the National Science Foundation (DGE‐2137424), U.S. Department of Energy (DE‐AC02‐76SF00515), National Institutes of Health (NIH S10 OD012245), and the Australian Research Council (ARC) Linkage Project LP200300886.

Supporting information

Supporting File: ansa70116‐sup‐0001‐SuppMat.pdf.

Acknowledgements

This material is based upon work supported by the National Science Foundation Graduate Research Fellowship Program under Grant Number DGE‐2137424. Any opinions, findings, and conclusions or recommendations expressed in this material are those of the author(s) and do not necessarily reflect the views of the National Science Foundation. Portions of this work were carried out at the Stanford Synchrotron Radiation Lightsource, SLAC National Accelerator Laboratory, supported by the U.S. Department of Energy, Office of Science, Office of Basic Energy Sciences under Contract No. DE‐AC02‐76SF00515, and we thank the user support staff at SSRL. The authors acknowledge the UW‐Madison Department of Chemistry SynCat Center for providing the Tensor 27 FTIR spectrometer supporting this work. The Bruker Avance‐600 NMR spectrometer in the Paul Bender Chemistry Instrumentation Center was supported by NIH S10 OD012245, and we thank the staff at the NMR facility. This work was performed in part at the Trace Analysis for Chemical, Earth and Environmental Sciences (TrACEES) Platform at the University of Melbourne, and we acknowledge Dr. Yukie O'Bryan for her support. The authors acknowledge Jo McDonald for liaison with Indigenous partner organizations and Annie Carson for valuable discussions on Australian exudate usage. We acknowledge Keeley Richardson for assistance with sample images. We gratefully acknowledge the use of samples from the following: Historic collection from Forensic Science South Australia (Prof Paul Kirkbride and Prof Paul Pigou); modern samples from: Waite Arboretum, Adelaide, South Australia, Australia (Kate Delaporte), University of Melbourne System Gardens, Melbourne, Victoria, Australia (Virginia McNally), Martu Country, Western Australia, Australia (MNR and Michi Meier), Balanggarra Country, Western Australia, Australia (Bernadette Waina), and experimental archaeology samples (Dr. Phillip Green). We are grateful to various researchers and collaborators who originated and maintained the samples over the decades, and we acknowledge the Indigenous lands where the samples originated. We acknowledge the Balanggarra Aboriginal Corporation, the Kalumburu Community, Rangers and Traditional Owners for their stewardship of the land, permission to work on their Country, providing pivotal access to the sites and sharing their cultural knowledge associated with the rock shelters and rock art. Many thanks to Dunkeld Pastoral Company, Dan Horsford, Pauline Heaney, and Paul Hartley for their hospitality and logistical support during fieldwork. Analysed samples were also provided through funding from the Australian Research Council (ARC) Linkage Project LP200300886 from the Desert to the Sea: Managing Rock Art, Country and Culture (DTTS). The DTTS research collaboration includes Martu people represented by Jamukurnu‐Yapalikurnu Aboriginal Corporation (JYAC) and Mungarlu Ngurrarankatja Rirraunkaja (Aboriginal Corporation—MNR) RNTBC and is covered by Ethics Approval granted by UWA (2023/ET000143). These results have been shared with the JYAC and MNR Boards, and this paper has been approved for publication by JYAC. University of Melbourne STEMM 1282 Ethics approval under Project 27353, Reference Number 2026‐27353‐68621‐9.

Contributor Information

Sophia A. Vogelsang, Email: svogelsang@wisc.edu.

Rachel S. Popelka‐Filcoff, Email: rachel.popelkafilcoff@unimelb.edu.au.

Uwe Bergmann, Email: ubergmann@wisc.edu.

Data Availability Statement

The data underlying this study are openly available in Figshare at https://doi.org/10.6084/m9.figshare.32320356 [67].

References

  • 1. Langenheim J. H., Markman J., and Thordarsen G., Plant Resins: Chemistry, Evolution, Ecology, and Ethnobotany (Timber Press, 2003). [Google Scholar]
  • 2. Nussinovitch A., Plant Gum Exudates of the World Sources, Distribution, Properties, and Applications (CRC Press, 2010). [Google Scholar]
  • 3. Mantell C. L., “The Natural Hard Resins—Their Botany, Sources and Utilization,” Economic Botany 4 (1950): 203–242, 10.1007/BF02859481. [DOI] [Google Scholar]
  • 4. Bisulca C., Pool M., Henkin J. M., and Odegaard N., “Mesquite Exudates and Insect Lac: O'odham Use and Hohokam Traditions,” Am Antiq 91, no. 3 (2026): 1–14, 10.1017/aaq.2026.10179. [DOI] [Google Scholar]
  • 5. Clarke P. A., Aboriginal People and Their Plants (Rosenberg Publishing, 2007). [Google Scholar]
  • 6. Clarke P. A., Australian Plants as Aboriginal Tools (Rosenberg Publishing, 2012). [Google Scholar]
  • 7. Powell O., Fensham R. J., and Memmott P., “Indigenous Use of Spinifex Resin for Hafting in North‐Eastern Australia,” Economic Botany 67, no. 3 (2013): 210–224, 10.1007/s12231-013-9238-3. [DOI] [Google Scholar]
  • 8. Pitman H. T. and Wallis L. A., “The Point of Spinifex: Aboriginal Uses of Spinifex Grasses in Australia,” Ethnobotany Research and Applications 10 (2012): 109, 10.17348/era.10.0.109-131. [DOI] [Google Scholar]
  • 9. Tworek‐Matuszkiewicz B., “Australian Aboriginal Bark Paintings—their History, Structure and Conservation,” Studies in Conservation 52 (2007): 15–28, 10.1179/sic.2007.52.supplement-1.15. [DOI] [Google Scholar]
  • 10. Alcock S., “Painting Country: Australian Aboriginal Artists′ approach to Traditional Materials in a Modern Context,” AICCM Bulletin 34, no. 1 (2013): 66–74, 10.1179/bac.2013.34.1.008. [DOI] [Google Scholar]
  • 11. Clarkson C., Jacobs Z., Marwick B., et al., “Human Occupation of northern Australia by 65,000 Years Ago,” Nature 547, no. 7663 (2017): 306–310, 10.1038/nature22968. [DOI] [PubMed] [Google Scholar]
  • 12. Blee A. J., Walshe K., Pring A., Quinton J. S., and Lenehan C. E., “Towards the Identification of Plant and Animal Binders on Australian Stone Knives,” Talanta 82, no. 2 (2010): 745–750, 10.1016/j.talanta.2010.05.044. [DOI] [PubMed] [Google Scholar]
  • 13. Matheson C. D., “Characterisation of the Physico‐Chemical and Optical Properties of Australian Native Plant Exudates for a Simple Method to Determine Archaeological Resins and Gums,” Journal of Archaeological Science: Reports 42 (2022): 1‐10, 10.1016/j.jasrep.2022.103360. [DOI] [Google Scholar]
  • 14. Bradshaw F., “Chemical Characterisation of Museum‐Curated Ethnographic Resins From Australia and New Guinea Used as Adhesives, Medicines and Narcotics,” Heritage Science 1, no. 1 (2013): 36, 10.1186/2050-7445-1-36. [DOI] [Google Scholar]
  • 15. Reeves T., Popelka‐Filcoff R. S., and Lenehan C. E., “Towards Identification of Traditional European and Indigenous Australian Paint Binders Using Pyrolysis Gas Chromatography Mass Spectrometry,” Analytica Chimica Acta 803, no. 0 (2013): 194–203, 10.1016/j.aca.2013.09.012. [DOI] [PubMed] [Google Scholar]
  • 16. Matheson C. D. and McCollum A. J., “Characterising Native Plant Resins From Australian Aboriginal Artefacts Using ATR‐FTIR and GC/MS,” Journal of Archaeological Science 52, no. 0 (2014): 116–128, 10.1016/j.jas.2014.08.016. [DOI] [Google Scholar]
  • 17. Bindon P., Useful Bush Plants (Western Australian Museum, 1996). [Google Scholar]
  • 18. Łucejko J. J., Bertelli I., Costa R., et al., “Characterising Terpenic Plant Resins, Wood Tars and Pitches in Heritage Science: Analytical Methods and Applications,” npj Heritage Science 14, no. 1 (2026): 162, 10.1038/s40494-026-02426-6. [DOI] [Google Scholar]
  • 19. Granzotto C., Arslanoglu J., Rolando C., and Tokarski C., Plant Gum Identification in Historic Artworks (Nature Publishing Group, 2017), 10.1038/srep44538. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 20. Georgiou R., Popelka‐Filcoff R. S., Sokaras D., et al., “Disentangling the Chemistry of Australian Plant Exudates From a Unique Historical Collection,” Proceedings of the National Academy of Sciences 119, no. 22 (2022): e2116021119, 10.1073/pnas.2116021119. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 21. Mann A. K., Appadoo D., Lenehan C. E., and Popelka‐Filcoff R. S., “Combining ATR Far‐ and Mid‐Infrared Spectroscopy to Distinguish Native Australian Plant Exudates for Cultural Heritage Analysis,” Journal of Archaeological Science 176 (2025): 106167, 10.1016/j.jas.2025.106167. [DOI] [Google Scholar]
  • 22. Parr J. F., “The Identification of Xanthorrhoea Resins by Starch Morphology: Prospects for Archaeological and Taxonomic Applications1,” Economic Botany 56, no. 3 (2002): 260–270, 10.1663/0013-0001(2002)056[0260:TIOXRB]2.0.CO;2. [DOI] [Google Scholar]
  • 23. Lambert J. B., Wu Y., Kozminski M. A., and Santiago‐Blay J. A., “Characterization of Eucalyptus and Chemically Related Exudates by Nuclear Magnetic Resonance Spectroscopy,” Australian Journal of Chemistry 60, no. 11 (2007): 862–870, 10.1071/CH07163. [DOI] [Google Scholar]
  • 24. Lambert J. B., Wu Y., and Santiago‐Blay J. A., “Taxonomic and Chemical Relationships Revealed by Nuclear Magnetic Resonance Spectra of Plant Exudates,” Journal of Natural Products 68, no. 5 (2005): 635–648, 10.1021/np050005f. [DOI] [PubMed] [Google Scholar]
  • 25. Lambert J. B., Heckenbach E. A., Wu Y., and Santiago‐Blay J. A., “Characterization of Plant Exudates by Principal‐Component and Cluster Analyses With Nuclear Magnetic Resonance Variables,” Journal of Natural Products 73, no. 10 (2010): 1643–1648, 10.1021/np100318n. [DOI] [PubMed] [Google Scholar]
  • 26. Schülke W., Electron Dynamics by Inelastic X‐Ray Scattering (Oxford University Press, 2007), 10.1093/oso/9780198510178.001.0001. [DOI] [Google Scholar]
  • 27. Bergmann U., Glatzel P., and Cramer S. P., “Bulk‐Sensitive XAS Characterization of Light Elements: From X‐ray Raman Scattering to X‐ray Raman Spectroscopy,” Microchemical Journal 71 (2002): 221–230, 10.1016/S0026-265X(02)00014-0. [DOI] [Google Scholar]
  • 28. Gueriau P., Rueff J.‐P., Bernard S., et al., “Noninvasive Synchrotron‐Based X‐ray Raman Scattering Discriminates Carbonaceous Compounds in Ancient and Historical Materials,” Analytical Chemistry 89, no. 20 (2017): 10819–10826, 10.1021/acs.analchem.7b02202. [DOI] [PubMed] [Google Scholar]
  • 29. Georgiou R., Gueriau P., Sahle C. J., et al., “Carbon Speciation in Organic Fossils Using 2D to 3D X‐ray Raman Multispectral Imaging,” Science Advances 5 (2019): eaaw5019, 10.1126/sciadv.aaw5019. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 30. Cazals L., Desolneux A., Huotari S., et al., “Digital Twin Enables Radiosensitive Organic Speciation in 3D,” Science Advances 11, no. 41 (2025): eadw5444, 10.1126/sciadv.adw5444. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 31. Rots V., Hayes E., Akerman K., et al., “Hafted Tool‐Use Experiments With Australian Aboriginal Plant Adhesives: Triodia Spinifex, Xanthorrhoea Grass Tree and Lechenaultia Divaricata Mindrie,” EXARC Journal 2020, no. 1 (2020): 1‐11, https://exarc.net/ark:/88735/10487. [Google Scholar]
  • 32. Lambert J. B., Shurvell H. F., Lightner D. A., and Cooks G. R., Organic Structural Spectroscopy (Prentice Hall, 1998). [Google Scholar]
  • 33. Bellamy L. J., The Infra‐Red Spectra of Complex Molecules (Springer Dordrecht, 1975), 10.1007/978-94-011-6017-9. [DOI] [Google Scholar]
  • 34. Lin‐Vien D., Colthup N. B., Fateley W. G., and Grasselli J. G., The Handbook of Infrared and Raman Characteristic Frequencies of Organic Molecules (Elsevier, 1991). [Google Scholar]
  • 35. Sokaras D., Nordlund D., Weng T.‐C., et al., “A High Resolution and Large Solid Angle X‐ray Raman Spectroscopy End‐Station at the Stanford Synchrotron Radiation Lightsource,” Review of Scientific Instruments 83, no. 4 (2012): 043112, 10.1063/1.4704458. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 36. Riedo C., Scalarone D., and Chiantore O., “Advances in Identification of Plant Gums in Cultural Heritage by Thermally Assisted Hydrolysis and Methylation,” Analytical and Bioanalytical Chemistry 396, no. 4 (2010): 1559–1569, 10.1007/s00216-009-3325-4. [DOI] [PubMed] [Google Scholar]
  • 37. Andreotti A., Bonaduce I., Colombini M. P., Modugno F., and Ribechini E., “A Diagnosis of the Yellowing of the Marble High Reliefs and the Black Decorations in the Chapel of the Tomb of Saint Anthony (Padua, Italy),” Special Issue: Art, Culture and Heritage 284, no. 1 (2009): 123–130, 10.1016/j.ijms.2008.11.008. [DOI] [Google Scholar]
  • 38. Pedregosa F., Varoquaux G., Org N., et al., “Scikit‐Learn: Machine Learning in Python,” Journal of Machine Learning Research 12 (2011): 2825–2830. [Google Scholar]
  • 39. Ioannidis K., Melliou E., and Magiatis P., “High‐Throughput 1H‐Nuclear Magnetic Resonance‐Based Screening for the Identification and Quantification of Heartwood Diterpenic Acids in Four Black Pine (Pinus nigra Arn.) Marginal Provenances in Greece,” Molecules 24, no. 19 (2019): 3603, 10.3390/molecules24193603. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 40. Ramnath M. G., Thirugnanasampandan R., Sadasivam M., and Mohan P. S., “Antioxidant, Antibacterial and Antiacetylcholinesterase Activities of Abietic Acid From Isodon wightii (Bentham) H. Hara,” Free Radicals and Antioxidants 5, no. 1 (2015): 1–5, 10.5530/fra.2015.1.1. [DOI] [Google Scholar]
  • 41. Gigante B., Santos L., Marcelo‐Curto M. J., and Ascenso J., “ 13C and 1H NMR Assignments for a Series of Dehydroabietic Acid Derivatives,” Magnetic Resonance in Chemistry 33, no. 4 (1995): 318–321, 10.1002/mrc.1260330416. [DOI] [Google Scholar]
  • 42. Woldemichael G. M., Wächter G., Singh M. P., Maiese W. M., and Timmermann B. N., “Antibacterial Diterpenes From Calceolaria pinifolia ,” Journal of Natural Products 66, no. 2 (2003): 242–246, 10.1021/np020380x. [DOI] [PubMed] [Google Scholar]
  • 43. Seca A. M. L., Pinto D., and Silva A. M. S., “Structural Elucidation of Pimarane and Isopimarane Diterpenoids: The 13C NMR Contribution,” Natural Products Communications 3, no. 3 (2008): 399–412, 10.1177/1934578x08003003. [DOI] [Google Scholar]
  • 44. Sawi S. A. E. and Motawe H. M., “Labdane, Pimarane and Abietane Diterpenes From the Fruits of Juniperus phoenica L. Grown in Egypt and Their Activities against Human Liver Carcinoma,” Canadian Journal of Pure & Applied Science 2, no. 1 (2008): 115–122. [Google Scholar]
  • 45. Skakovskii E. D., Tychinskaya L. Y., Gaidukevich O. A., et al., “NMR Determination of the Composition of Balsams From Scotch Pine Resin,” Journal of Applied Spectroscopy 75, no. 3 (2008): 439–443, 10.1007/s10812-008-9065-y. [DOI] [Google Scholar]
  • 46. Sugimoto N., Kuroyanagi M., Kato T., et al., “Identification of the Main Constituents in Sandarac Resin, a Natural Gum Base,” Journal of the Food Hygienic Society of Japan (Shokuhin Eiseigaku Zasshi) 47, no. 2 (2006): 76–79, 10.3358/shokueishi.47.76. [DOI] [PubMed] [Google Scholar]
  • 47. Kononenko I., Molecular Characterization and Ageing of the Sandarac Resin and Its Principal Component Communic Acid (Université Pierre et Marie Curie—Paris VI, 2017), https://theses.hal.science/tel‐01754771. [Google Scholar]
  • 48. Soliman A. F., Naeem Z. M., Khalil A. T., Shimizu K., and El‐Sharkawy S. H., “Microbial Transformation of the Labdane Diterpene 13‐epi‐cupressic Acid,” World Journal of Pharmaceutical Sciences 6, no. 5 (2018): 61–69. [Google Scholar]
  • 49. Carpenter C. D., O'Neill T., Picot N., et al., “Anti‐Mycobacterial Natural Products From the Canadian Medicinal Plant Juniperus communis,” Journal of Ethnopharmacology 143, no. 2 (2012): 695–700, 10.1016/j.jep.2012.07.035. [DOI] [PubMed] [Google Scholar]
  • 50. Viet T. D., Xuan T. D., and Anh L. H., “α‐Amyrin and β‐Amyrin Isolated From Celastrus Hindsii Leaves and Their Antioxidant, Anti‐Xanthine Oxidase, and Anti‐Tyrosinase Potentials,” Molecules 26, no. 23 (2021): 7248, 10.3390/molecules26237248. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 51. Lee S., “α‐Pinene and myrtenol: Complete 1H NMR Assignment,” Magnetic Resonance in Chemistry 40, no. 4 (2002): 311–312, 10.1002/mrc.972. [DOI] [Google Scholar]
  • 52. Scalarone D., Lazzari M., and Chiantore O., “Ageing Behaviour and Analytical Pyrolysis Characterisation of Diterpenic Resins Used as Art Materials: Manila Copal and Sandarac,” Journal of Analytical and Applied Pyrolysis 68‐69 (2003): 115–136, 10.1016/S0165-2370(03)00005-6. [DOI] [Google Scholar]
  • 53. Mondal S., Memmott P., Wallis L., and Martin D., “Physico‐Thermal Properties of Spinifex Resin Bio‐Polymer,” Materials Chemistry and Physics 133, no. 2 (2012): 692–699, 10.1016/j.matchemphys.2012.01.058. [DOI] [Google Scholar]
  • 54. Lambert J. B., Heckenbach E. A., Hurtley A. E., Wu Y., and Santiago‐Blay J. A., “Nuclear Magnetic Resonance Spectroscopic Characterization of Legume Exudates,” Journal of Natural Products 72, no. 6 (2009): 1028–1035, 10.1021/np900188j. [DOI] [PubMed] [Google Scholar]
  • 55. Lambert J. B., Donnelly E. W., Heckenbach E. A., et al., “Molecular Classification of the Natural Exudates of the rosids,” Phytochemistry 94 (2013): 171–183, 10.1016/j.phytochem.2013.06.013. [DOI] [PubMed] [Google Scholar]
  • 56. Anderson D. M. W. and Wang W., “Composition of the Gum from Combretum paniculatum and Four Other Gums Which Are Not Permitted Food Additives,” Phytochemistry 29, no. 4 (1990): 1193–1195, 10.1016/0031-9422(90)85427-H. [DOI] [PubMed] [Google Scholar]
  • 57. Anderson D. M. W. and Leon De Pinto G., “Gum Exudates from the Genus Grevillea (Proteaceae),” Carbohydrate Polymers 2 (1982): 19–24, 10.1016/0144-8617(82)90042-X. [DOI] [Google Scholar]
  • 58. Hirst E. L., Percival E., and Williams R. S., “394. The Structure of Brachychiton Diversifolium Gum (Sterculia caudata),” Journal of the Chemical Society 161 (1958): 1942–1950, 10.1039/JR9580001942. [DOI] [Google Scholar]
  • 59. Eagles P. F. K., Stephen A. M., and Churms S. C., “Molecular Structures of Gum Exudates From Hakea Species,” Phytochemistry 34, no. 3 (1993): 709–713, 10.1016/0031-9422(93)85344-Q. [DOI] [PubMed] [Google Scholar]
  • 60. Nobakht M., Grkovic T., Trueman S., et al., “Chemical Constituents of Kino Extract From Corymbia torelliana,” Molecules 19, no. 11 (2014): 17862–17871, 10.3390/molecules191117862. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 61. Faleva A. V., Falev D. I., Onuchina A. A., Ulyanovskii N. V., and Kosyakov D. S., “Comprehensive Identification of Polyphenolic Metabolites in Aspen Knotwood by Combination of 2D NMR and HPLC‐HRMS,” Phytochemical Analysis 36, no. 1 (2025): 307–316, 10.1002/pca.3443. [DOI] [PubMed] [Google Scholar]
  • 62. Lavoie S., Ouellet M., Fleury P., Gauthier C., Legault J., and Pichette A., “Complete 1H and13C NMR Assignments of a Series of Pergalloylated Tannins,” Magnetic Resonance in Chemistry 54, no. 2 (2016): 168–174, 10.1002/mrc.4328. [DOI] [PubMed] [Google Scholar]
  • 63. Lambert J. B., Santiago‐Blay J. A., Wu Y., Contreras T. A., Johnson C. L., and Bisulca C. M., “Characterization of Phenolic Plant Exudates by Nuclear Magnetic Resonance Spectroscopy,” Journal of Natural Products 84, no. 9 (2021): 2511–2524, 10.1021/acs.jnatprod.1c00522. [DOI] [PubMed] [Google Scholar]
  • 64. Shen C.‐C., Chang Y.‐S., and Hott L.‐K., “Nuclear Magnetic Resonance Studies of 5,7‐Dihydroxyflavonoids,” Phytochemistry 34, no. 3 (1993): 843–845, 10.1016/0031-9422(93)85370-7. [DOI] [Google Scholar]
  • 65. Anderson D. M. W., Howlett J. F., and McNab C. G. A., “The Hydroxyproline Content of Gum Exudates From Several Plant Genera,” Phytochemistry 26, no. 1 (1987): 309–311, 10.1016/S0031-9422(00)81534-4. [DOI] [Google Scholar]
  • 66. Churms S. C. and Stephen A. M., “Studies of the Molecular Core of Grevillea Robusta Gum,” Carbohydrate Research 167 (1987): 239–255, 10.1016/0008-6215(87)80282-3. [DOI] [Google Scholar]
  • 67.Vogelsang et al., “Australian Plant Exudates FTIR, XRS, NMR, and py‐GCMS Datasets,” Figshare (2026), 10.6084/m9.figshare.32320356. [DOI] [Google Scholar]

Associated Data

This section collects any data citations, data availability statements, or supplementary materials included in this article.

Supplementary Materials

Supporting File: ansa70116‐sup‐0001‐SuppMat.pdf.

Data Availability Statement

The data underlying this study are openly available in Figshare at https://doi.org/10.6084/m9.figshare.32320356 [67].


Articles from Analytical Science Advances are provided here courtesy of Wiley

RESOURCES