Skip to main content
Nanomaterials logoLink to Nanomaterials
. 2026 Oct 22;16(21):1336. doi: 10.3390/nano16211336

Linking Stoichiometry, Chemical Pressure, and Domain Structure in the van der Waals Ferrielectric CuInP2S6

Dávid Gál 1,2, Sándor Lenk 3, István Rigó 1, Miklós Veres 1, László Péter 1, Anton Kohutych 4, Konstantin Glukhov 4, Nyomó Dominika 4, Alexander Molnar 4,*
Editor: Dong-Joo Kim
PMCID: PMC13764896  PMID: 43029357

Abstract

The ferrielectric properties of layered CuInP2S6 (CIPS) are highly sensitive to stoichiometry and growth-induced defects. Here we systematically compare crystals grown by chemical vapor transport and the Bridgman–Stockbarger method with Cu- and In-enriched samples, combining compositional analysis, dielectric spectroscopy, uniaxial-pressure measurements, Raman spectroscopy, piezoresponse force microscopy and first-principles calculations. The transition temperature increases systematically from 307 K (Bridgman) to 312 K (Cu-enriched), 317 K (gas transport) and 322 K (In-enriched). In enrichment is consistent with spontaneous CIPS/In4/3P2S6 phase segregation that generates effective positive chemical pressure, stabilizing the ferrielectric state and producing a strongly biased, pinned domain configuration. Cu enrichment produces the opposite response—lower TC, enhanced dielectric loss and a fragmented domain morphology—characteristic of a negative-pressure-like perturbation of the Cu-ion energy landscape. Landau–Ginzburg–Devonshire analysis and density functional calculations provide a unified microscopic picture based on Cu-ion configurational freedom and interlayer coupling. Growth defects act as an independent source of domain-wall pinning. Together, these results establish stoichiometry and synthesis conditions as practical tools for engineering ferrielectric order in van der Waals CIPS.

Keywords: CuInP2S6, van der Waals ferrielectrics, stoichiometry, phase transition, dielectric properties, domain structure

1. Introduction

Layered metal thio- and selenophosphates have attracted considerable attention because their low-dimensional crystal structures combine van der Waals bonding with a broad range of functional electronic and ferroic properties [1,2]. Among these materials, CuInP2S6 (CIPS) is particularly interesting as a layered ferrielectric that retains spontaneous polarization down to the nanoscale [3,4]. This combination of reduced dimensionality and switchable polarization has motivated extensive research toward CIPS-based ferroelectric field-effect transistors [5], negative-capacitance devices [6], memristors [7], and neuromorphic and optoelectronic synaptic devices [8,9]. However, the relatively low ferrielectric transition temperature, TC ≈ 315 K, limits the temperature range of the polar state, while the pronounced sensitivity of CIPS properties to growth conditions and stoichiometry presents both a reproducibility challenge and an opportunity for controlled materials engineering.

CuInP2S6 has a layered structure in which Cu, In, and P–P pairs occupy octahedral sites within a sulfur framework [10]. Individual layers are weakly coupled by van der Waals interactions, making the structure particularly sensitive to changes in interlayer spacing and cation distribution. The ferrielectric ordering is closely associated with the displacement and redistribution of Cu+ ions among several energetically nonequivalent positions (Cu1, Cu2, and Cu3; Figure 1) [11]. Above TC, thermally activated Cu-ion hopping between available sites contributes to dynamic disorder, whereas cooling through the transition preferentially stabilizes off-center Cu positions together with oppositely directed displacements of the In3+ sublattice. The resulting partially compensating polar sublattices produce the ferrielectric state. Consequently, modifications of the Cu-ion potential landscape, site occupancy, or interlayer coupling can strongly affect the transition temperature and polarization behavior of CIPS.

Figure 1.

Figure 1

(a) Layered crystal structure of CuInP2S6 viewed along the a axis. (b) Local sulfur coordination showing the Cu1, Cu2, and Cu3 positions [11].

An important route for modifying the properties of CIPS is deviation from stoichiometry. Dziaugys et al. [12] demonstrated that In enrichment increases the phase-transition temperature, with TC reaching approximately 330 K in crystals grown with excess In2S3. Subsequent studies showed that In-rich, Cu-deficient CIPS undergoes spontaneous chemical phase separation rather than forming a homogeneous solid solution [13,14]. The resulting structure consists of coexisting ferrielectric CuInP2S6 and centrosymmetric In4/3P2S6 (IPS) chemical domains within individual layers. Importantly, the lateral dimensions and spatial organization of these domains depend strongly on the thermal history, providing a means of controlling the mesoscale chemical architecture of CIPS/IPS heterostructures [13,14].

The formation of CIPS/IPS chemical domains has important structural and functional consequences. With decreasing Cu content, the transition temperature of the CIPS component increases despite the reduced fraction of the ferrielectric phase [14]. X-ray diffraction reveals a systematic composition dependence of the interlayer spacing, which increases from approximately 6.5054 Å in In4/3P2S6 to 6.5146 Å in CuInP2S6 [14]. More importantly, the coexistence of the two phases produces substantial and opposite strains in the CIPS and IPS regions [14,15]. This mutual strain provides a physical basis for interpreting the effect of In enrichment on the CIPS phase as an effective positive chemical pressure. The interfaces between the chemical phases also modify Cu-ion transport and conductivity [16], while the observed coupling between CIPS/IPS chemical domains and ferrielectric domains demonstrates that compositional heterogeneity, strain, and polarization organization are intrinsically interconnected [15].

The strain effects associated with compositional heterogeneity suggest a close connection between stoichiometry and mechanical pressure. External pressure is known to strongly modify the ferrielectric transition in CIPS [17,18,19,20]. In the low-pressure regime most relevant to the present work, hydrostatic compression shifts TC toward higher temperatures, with a reported pressure coefficient dTC/dp ≈ 210 K GPa−1 [18,19]. A similar trend is observed under uniaxial compression, where TC increases to approximately 324 K at 0.06 GPa [20]. Hydrostatic pressure also modifies the Cu-ion distribution and can substantially enhance the spontaneous polarization through the increased occupation of interlayer Cu sites [21]. These observations emphasize the strong coupling between mechanical compression, Cu-site occupancy, and ferrielectric ordering, and are consistent with the order–disorder character of the phase transition in CIPS.

At higher pressures, the response of CIPS becomes substantially more complex, involving pronounced changes in Cu coordination, interlayer geometry, lattice dynamics, and eventually crystal symmetry [17,22]. Pressure-induced changes in Cu-related vibrational modes were observed by Raman spectroscopy [17], while the assignment of these modes to Cu-ion dynamics is consistent with earlier temperature-dependent Raman studies [23]. These transformations further emphasize the exceptional sensitivity of the CIPS lattice to the Cu-ion configuration; however, the high-pressure structural regimes lie outside the effective chemical-pressure analogy considered in the present work. Here, the relevant comparison is restricted primarily to the low-pressure regime, in which CIPS remains in the ferrielectric phase and compression modifies Cu-site occupancy and interlayer coupling without inducing the major structural transformations characteristic of higher pressures [24].

Taken together, these studies reveal a striking parallel between the compositional and mechanical control of ferrielectricity in CIPS. External compression increases TC, modifies Cu-site occupancy, and affects Cu-ion mobility [18,19,20,21,24], whereas In-rich, Cu-deficient CIPS is known to form CIPS/IPS chemical heterostructures in which lattice mismatch generates compressive strain in the CIPS regions and is likewise accompanied by an increase in TC [13,14,15]. Conversely, the systematic increase in interlayer spacing with increasing Cu content [14] suggests that Cu enrichment may drive the lattice in the opposite direction, producing a tensile or negative-pressure-like response. These observations raise the possibility that deviations from stoichiometry and externally applied pressure act on common microscopic degrees of freedom associated with Cu-ion configuration and interlayer coupling. However, a systematic experimental connection between stoichiometry, effective pressure, lattice dynamics, dielectric response, and ferrielectric domain organization in CuInP2S6 has not yet been established.

In this work, we systematically investigate how crystal growth and controlled deviations from stoichiometry modify the ferrielectric properties of CuInP2S6. Crystals grown by chemical vapor transport and the Bridgman–Stockbarger method are compared with Cu- and In-enriched samples using compositional analysis, dielectric spectroscopy, Raman spectroscopy, and piezoresponse force microscopy. We show that In enrichment produces a response characteristic of effective positive chemical pressure, whereas Cu enrichment drives the system toward a negative-pressure-like state. The resulting changes in TC, dielectric response, lattice dynamics, and domain morphology can be consistently understood in terms of modifications of the Cu-ion potential landscape, site occupancy, and interlayer coupling. This establishes a unified physical framework linking growth conditions and stoichiometry to chemical pressure and, ultimately, to the mesoscale ferrielectric domain structure of CuInP2S6.

2. Materials and Methods

2.1. Crystal Growth and Sample Preparation

CuInP2S6 crystals were first synthesized by Nitsche using chemical vapor transport reactions [25], and the subsequent development of melt-growth approaches, including the Bridgman–Stockbarger method [26], enabled the preparation of substantially larger bulk crystals. In the present work, single crystals were grown by both chemical vapor transport (CVT) and directional crystallization from the melt. In addition to nominally stoichiometric CuInP2S6, crystals with controlled deviations from stoichiometry were prepared from starting mixtures enriched with either Cu2S or In2S3.

For CVT growth, the starting materials were sealed in evacuated quartz ampoules approximately 15 cm in length, with CuI used as the transport agent. The temperature of the hot zone was maintained at 913–943 K and that of the cold zone at 903–913 K, corresponding to a temperature difference of 20–40 K. The resulting crystals formed thin platelets whose major faces were parallel to the structural layers; the layer normal was approximately along c*. In addition to nominally stoichiometric material, Cu- and In-enriched crystals were grown from starting mixtures containing 90 wt.% CuInP2S6 and 10 wt.% Cu2S, and 90 wt.% CuInP2S6 and 10 wt.% In2S3, respectively. Thus, the coefficients 0.9 and 0.1 used to denote these starting mixtures correspond to mass fractions rather than molar fractions.

Bulk CuInP2S6 crystals were also prepared by directional crystallization from the melt using the Bridgman–Stockbarger method in a two-zone furnace [27]. The melt and annealing zones were maintained at 1150 and 870 K, respectively, with a temperature gradient of approximately 3 K mm−1 in the crystallization region. The crystallization front was advanced at 2.5 mm day−1, followed by cooling at approximately 200 K day−1. The starting material was synthesized from high-purity elemental components in stoichiometric proportions in quartz ampoules evacuated to approximately 0.013 Pa. The resulting ingots had a diameter of approximately 14 mm and a cylindrical length of 20–25 mm. Representative photographs of the four crystal types are shown in Figure 2.

Figure 2.

Figure 2

Photographs of CuInP2S6 samples obtained using different growth methods and starting compositions: 1—gas transport-grown CuInP2S6, 2—Bridgman–Stockbarger-grown CuInP2S6, 3—Cu-enriched CuInP2S6 + Cu2S, and 4—In-enriched CuInP2S6 + In2S3.

2.2. Structural and Compositional Characterization

Surface morphology and chemical composition were examined using a TESCAN MIRA 3 (TESCAN, Brno, Czech Republic) scanning electron microscope equipped with an EDAX energy-dispersive X-ray spectroscopy (EDS) system (EDAX Inc., Mahwah, NJ, USA). Spectra were acquired and processed using EDAX APEX software (version 3.1). The samples were mounted on double-sided conductive carbon tape (Ted Pella, Redding, CA, USA). The compositions reported in Table 1 were obtained by averaging 5–7 local measurements acquired at different positions. Representative SEM images, quantitative results, and EDS spectra are provided in Figures S1–S4 of the Supplementary Materials. The EDS-derived averaged compositions were used to quantify the relative Cu/In deviations from stoichiometry across the investigated sample series.

Table 1.

EDS-derived averaged compositions and ferrielectric transition temperatures TC of the investigated CuInP2S6 crystals. The compositions represent averages of 5–7 measurements acquired at different sample locations.

Sample EDS Composition TC (K)
CuInP2S6 (gas transport) Cu1.02In1.04P2.03S6 317
CuInP2S6 (Bridgman–Stockbarger) Cu1.10In0.93P2.04S6 307
CuInP2S6 + Cu2S Cu1.05In0.97P2S6.01 312
CuInP2S6 + In2S3 Cu0.75In1.15P2S6.02 322

The compositions reported in Table 1 represent averages of 5–7 EDS measurements acquired at different positions of each sample. For the representative spectra shown in the Supplementary Materials, the EDAX APEX eZAF quantification yielded overall analysis uncertainties of 8.40–9.28%. The corresponding element-specific estimated errors were approximately 3.4% for Cu and 4.7–4.8% for In. These values characterize the analytical uncertainty of the EDS quantification and should not be interpreted as point-to-point standard deviations.

2.3. Dielectric and Uniaxial-Pressure Measurements

Temperature-dependent dielectric measurements were performed using an automated computer-controlled system incorporating an immersion-type cryostat [28], a Measurement Computing (Norton, MA, USA) USB-TEMP-AI data-acquisition unit, and an OWON ODP3033 (OWON Technology Inc., Zhangzhou, China) programmable dc power supply. The system allowed heating and cooling rates between 0.001 and 1 K min−1. Temperature was monitored using a PT100/1509A platinum resistance thermometer (TDI Ltd., Southport, UK). The temperature-measurement resolution was 0.001 K, with an absolute accuracy of ±2.9 K at 73 K and ±0.27 K at 373 K.

The complex dielectric permittivity was measured using a GW Instek (Good Will Instrument Co., Ltd., New Taipei City, Taiwan) LCR-819 LCR meter over the frequency range 12 Hz–100 kHz [29]. Plate-like samples with thicknesses of approximately 50–100 µm were used, and gold electrodes with areas between approximately 2 × 2 and 5 × 5 mm2 were deposited on the major surfaces. Because these faces are parallel to the structural layers, the ac electric field was applied approximately normal to the layers. The ac measuring voltage was adjusted according to sample thickness so that the electric field amplitude was maintained at Eac = 1 V cm−1 for all samples. This field is far below the reported coercive field of Ec = 77 kV cm−1 [11], ensuring operation within the linear dielectric response regime.

To minimize the influence of previous thermal history (“memory” effects), all crystals were held at 100 °C for 3 h before each measurement series. Each dielectric measurement was repeated at least five times under identical conditions. The run-to-run variation of the transition temperature was below 0.1 K, which is smaller than the absolute accuracy of the platinum resistance thermometer (±0.27 K at 373 K). The dielectric data were reproducible within approximately 1%. Unless otherwise stated, temperature scans used for the comparison of the different compositions were performed at a cooling rate of 0.1 K min−1, which minimized temperature gradients across the thin crystals and reduced the broadening of the dielectric anomaly near TC.

For measurements under uniaxial compression, the mechanical load was transmitted to the gas transport-grown CuInP2S6 crystal through a quartz rod with a diameter of 5 mm and a gold-coated quartz plate. One end of the rod was brought into contact with the sample assembly, while calibrated masses from a standard laboratory weight set were placed on the opposite end. The applied force was calculated as F = mg, and the nominal applied stress was determined as σ = F/Ar, where Ar = πd2/4 is the cross-sectional area of the d = 5 mm quartz rod (Ar ≈ 19.6 mm2). The gold-coated quartz plate distributed the force over the sample surface and simultaneously served as one electrical electrode; the opposite electrode was connected to the base of the cryostat sample holder. In this geometry, the compressive stress was applied approximately normal to the structural layers. Before every pressure-measurement cycle, the sample was annealed for 3 h at 100 °C in the paraelectric phase, and each measurement was repeated at least five times. The run-to-run variation of the transition temperature was below 0.1 K.

2.4. Raman Spectroscopy

Room-temperature Raman spectra were acquired in reflection geometry using a Renishaw inVia (Renishaw plc, Wotton-under-Edge, UK) Raman microscope coupled to a Leica DM 2700 (Leica Microsystems GmbH, Wetzlar, Germany) optical microscope. An excitation wavelength of 785 nm was used, and the spectral resolution was approximately 0.7 cm−1. The recorded spectra extended from below 50 cm−1 to approximately 600 cm−1, covering both low-frequency cation/lattice modes and higher-frequency internal vibrations of the P2S6 units. For cross-sample comparison, the Raman spectra were normalized to the intensity of the prominent P–P-related Raman band. Spectral acquisition and processing were performed using Renishaw WiRE software (version 5.7).

For quantitative comparison, selected Raman bands were fitted using pseudo-Voigt profiles with a local linear background. Peak positions, full widths at half maximum (FWHM), and peak intensities normalized to the fitted P–P-related band were extracted using the same fitting procedure and spectral windows for all four samples.

2.5. Piezoresponse Force Microscopy

Piezoresponse force microscopy (PFM) measurements were performed under ambient conditions using a Dimension Icon atomic force microscope (Bruker, Billerica, MA, USA) equipped with Pt–Ir-coated SCM-PIT conductive probes. Both single-frequency PFM imaging and band-excitation imaging/local polarization-switching measurements were employed. Local switching measurements were typically performed using tip biases between −10 and +10 V.

Because CuInP2S6 exhibits a negative longitudinal piezoelectric coefficient d33, the PFM phase contrast was interpreted accordingly, with a 180° phase difference corresponding to antiparallel out-of-plane polarization states.

The CuInP2S6 samples were electrically connected to metal sample disks (Ted Pella, Prod. No. 16218) using conductive silver paste (Ted Pella, Prod. No. 16035), with the disks connected to ground. Fresh surfaces were prepared immediately before measurement by mechanical exfoliation using the “Scotch-tape” method [30]. PFM images were processed using Gwyddion v.2.49.20171219 [31]. The PFM response was calibrated using a periodically poled lithium niobate reference sample (AR-PPLN 900.241, Asylum Research, Santa Barbara, CA, USA).

For quantitative analysis of the local switching loops, the negative- and positive-branch switching thresholds, Vsw− and Vsw+, were determined from the minima of the corresponding PFM amplitude branches; the phase loops were used to verify the associated ~180° phase reversal. The local switching half-width and imprint voltage were calculated as Vc* = (Vsw+ − Vsw−)/2 and Vimprint = (Vsw+ + Vsw−)/2, respectively. For phase-state population analysis, all four PFM phase maps were processed using the same automated procedure: the RGB images were converted to CIELAB color space, the two dominant phase-contrast populations were separated using an Otsu threshold applied to the L* channel, and pixels within a transition interval of ±10% of the separation between the two population medians were excluded as domain-boundary or ambiguous pixels. The remaining pixels were used to calculate the relative areas of the two phase-contrast states.

2.6. Use of Generative AI Tools

During the preparation and revision of this manuscript, ChatGPT (OpenAI, GPT-5.6) was used for language refinement, restructuring and drafting support, and to assist with the code-based quantitative post-processing of already acquired Raman and PFM datasets; no experimental image content or quantitative data were generated or altered by GenAI. ChatGPT was not used for experimental design, data acquisition, or the generation of experimental data. All analysis procedures and numerical outputs were reviewed and verified by the authors.

3. Results

3.1. Dielectric Data

The temperature dependences of the real and imaginary components of the complex dielectric permittivity for the four investigated CuInP2S6 crystal types are compared in Figure 3. For direct comparison, the curves in Figure 3, Figure 4 and Figure 5 were recorded at a frequency of 10 kHz. The complete temperature–frequency dependences are presented in Figures S5–S8 of the Supplementary Materials. These data show a pronounced increase in the dielectric response and losses at low frequencies, consistent with a substantial contribution from electrical conductivity and Cu-ion transport [32]. At 10 kHz, this low-frequency conductive contribution is strongly reduced, providing a more reliable comparison of the dielectric anomalies associated with the ferrielectric phase transition.

Figure 3.

Figure 3

Temperature dependences of (a) the real ε′ and (b) the imaginary ε″ components of the complex dielectric permittivity at 10 kHz for CuInP2S6 crystals: 1—Bridgman–Stockbarger growth; 2—Cu-enriched CuInP2S6 + Cu2S; 3—gas transport growth; 4—In-enriched CuInP2S6 + In2S3. The curves numbered 1–4 are shown in green, blue, red, and magenta, respectively.

Figure 4.

Figure 4

Temperature dependence of the inverse real dielectric permittivity, 1/ε′, in the phase-transition region of CuInP2S6 crystals: 1—Bridgman–Stockbarger growth; 2—Cu-enriched CuInP2S6 + Cu2S; 3—gas transport growth; 4—In-enriched CuInP2S6 + In2S3. The curves numbered 1–4 are shown in green, blue, red, and magenta, respectively.

Figure 5.

Figure 5

Temperature dependences of (a) ε′ and (b) ε″ for the gas transport-grown CuInP2S6 crystal under uniaxial compression: 1—0 MPa; 2—5 MPa; 3—25 MPa. Curves 1, 2, and 3 are shown in red, green, and blue, respectively.

The complex dielectric permittivity is represented as

ε*(T,f)=ε′(T,f)−iε″(T,f)

Using the eiωt convention, ε′ and ε″ are the real and imaginary (dielectric-loss) components, respectively. The four samples exhibit pronounced differences in both the position and magnitude of the dielectric anomaly. The transition temperatures determined from the dielectric response increase in the sequence 307 K for the Bridgman–Stockbarger crystal, 312 K for the Cu-enriched CuInP2S6 + Cu2S crystal, 317 K for the gas transport crystal, and 322 K for the In-enriched CuInP2S6 + In2S3 crystal (Table 1). Thus, deviations from stoichiometry are accompanied by systematic shifts of the ferrielectric transition together with substantial changes in the peak values of ε′ and ε″.

It should be emphasized that composition and growth route are not independently varied for every sample in the present set. Therefore, the observed trends should not be interpreted as arising from Cu/In stoichiometry alone. Stoichiometry provides the dominant thermodynamic contribution to the shift of TC, whereas growth-related defects can additionally modify dielectric broadening, internal fields, and domain-wall pinning.

The gas transport crystal, which has a near-stoichiometric EDS composition, is used here as a practical reference state. Relative to this sample, In enrichment shifts the transition to higher temperature and markedly reduces both ε′ and ε″. This behavior is consistent with the spontaneous chemical phase separation reported for Cu-deficient, In-rich CuInP2S6 [13,14], which produces coexisting ferrielectric CuInP2S6 (CIPS) and centrosymmetric In4/3P2S6 (IPS) chemical domains. The reduced fraction of the ferrielectric CIPS component decreases the macroscopic dielectric response, while the lattice mismatch between the CIPS and IPS regions generates compressive strain. The resulting effective positive chemical pressure stabilizes the ferrielectric state and shifts the transition toward a higher temperature [13,14].

The systematic displacement of the dielectric anomaly is also evident in the inverse permittivity 1/ε′ shown in Figure 4. The minima and the subsequent high-temperature branches shift progressively toward higher temperature in the same sequence as the transition temperatures listed in Table 1, making the composition-dependent displacement of the phase transition particularly clear.

An additional characteristic of the In-enriched sample is the substantially lower dielectric loss in the paraelectric region (Figure 3b). Cu-ion redistribution among nonequivalent crystallographic sites is closely connected with the dielectric and ionic response of CuInP2S6 [11]. The suppressed ε″ observed in the In-rich sample therefore suggests that the CIPS/IPS chemical microstructure, together with the associated strain and pinning, restricts the long-range contribution of mobile Cu-related species to the dielectric response. In contrast, Cu enrichment shifts the transition below that of the gas transport reference and retains a comparatively strong dielectric loss contribution, indicating an opposite trend in the stability and mobility of the Cu sublattice.

To establish an experimental reference for the effect of mechanical compression, the dielectric response was also measured under uniaxial pressure. As shown in Figure 5, increasing compression shifts both the ε′ and ε″ anomalies toward higher temperature. The transition temperature increases from approximately 317 K at 0 MPa to about 319 K at 5 MPa and approximately 323 K at 25 MPa. Over this low-pressure interval, the shift is approximately linear and corresponds to a pressure coefficient of the order of 2 × 102 K GPa−1.

Figure 6 compares the present low-pressure results with previously reported pressure dependences [18,19]. Both datasets show a positive pressure coefficient of the transition temperature. The agreement demonstrates that relatively modest mechanical compression stabilizes the ferrielectric phase and provides a direct experimental reference for the comparison between mechanical pressure and stoichiometry-induced internal strain developed in Section 3.2.

Figure 6.

Figure 6

Pressure dependence of the ferrielectric transition temperature TC. Red symbols and the inset show the present uniaxial pressure data; blue symbols show data from Refs. [18,19]. The blue solid line connects the literature points as a guide to the eye, and the curved arrow indicates the enlarged low-pressure region shown in the inset.

3.2. Comparison of Stoichiometry and Pressure Effects

The dielectric results reveal a direct parallel between the effects of external compression and deviations from stoichiometry. Mechanical compression shifts the ferrielectric transition toward higher temperature, while among the compositionally modified samples the same trend is observed for In enrichment. Cu enrichment produces the opposite response and shifts the transition toward lower temperature. These observations indicate that stoichiometry and external pressure act, at least in the low-pressure regime, on closely related structural degrees of freedom that control the stability of the ferrielectric state.

Previous pressure studies provide an experimental basis for comparing the hydrostatic and uniaxial responses of CuInP2S6. For uniaxial stress applied approximately along [001], the reported coefficient is dTC/dσ3 ≈ 20 K kbar−1 (≈200 K GPa−1), whereas hydrostatic pressure measurements yield dTC/dp ≈ 210 K GPa−1 [18,19,20]. The present low-pressure uniaxial measurements give a coefficient of the same order. Thus, the additional pressure scale used below is based on the experimentally established near-equality of the transition temperature pressure coefficients, rather than on an assumption that hydrostatic and uniaxial loading are mechanically equivalent.

This behavior is consistent with the order–disorder character of the transition in CuInP2S6, in which compression modifies the relative stability and occupation of nonequivalent Cu positions. At low pressures, compression is also accompanied by an enhancement of the spontaneous polarization and redistribution of Cu ions among available sites [21]. The present comparison is therefore restricted to this low-pressure regime; the more complex structural transformations reported at substantially higher pressures [24] are outside the chemical pressure analogy considered here.

For a phenomenological comparison, the stoichiometry-induced shift of the transition temperature can also be expressed as an equivalent pressure using the experimentally established low-pressure coefficient:

peff ≈ [TC(x) − TC,ref](∂TC/∂p)mech

where TC,ref is the transition temperature of the near-stoichiometric reference crystal and (∂TC/∂p)mech is the mechanical pressure coefficient. This relation provides only an operational, order-of-magnitude scale for comparing the magnitude of the stoichiometry-induced TC shift with that produced by external mechanical compression. It is not intended to imply strict thermodynamic equivalence between chemical substitution and applied stress, because stoichiometric variation simultaneously alters local chemistry, defect density and (in the In-rich limit) the CIPS/IPS phase fraction.

The microscopic basis of this correspondence is particularly clear for In-rich crystals. Cu-deficient, In-enriched CuInP2S6 undergoes chemical phase separation into ferrielectric CIPS and centrosymmetric In4/3P2S6 (IPS) regions [13]. The lattice mismatch between these chemical domains produces strain in the CIPS component [14], so that In enrichment acts as an effective positive chemical pressure. The resulting increase in TC therefore follows the same direction as that produced by external compression.

Cu enrichment leads to the opposite tendency. The composition dependence of the interlayer spacing reported for the CIPS/IPS system [14] indicates that increasing the Cu content expands the van der Waals-separated structure relative to the In-rich limit. Accordingly, the decrease in TC observed for Cu-rich crystals can be described as a negative-pressure-like, or tensile, response. This terminology should be understood as an effective structural analogy: changes in stoichiometry simultaneously modify local chemistry, defect concentration, phase fraction, and Cu-ion configuration, and therefore cannot be reduced to mechanical pressure alone.

Figure 7 thus summarizes an experimentally useful correspondence between stoichiometry and pressure. Both parameters influence Cu-site occupancy (Cu1, Cu2, and Cu3) [11], interlayer geometry, and the barriers governing Cu-ion redistribution, thereby shifting the balance between long-range ferrielectric order and local dynamic disorder. This framework provides the basis for comparing the vibrational response of the same samples in Section 3.3 and, subsequently, their domain structures.

Figure 7.

Figure 7

Pressure–stoichiometry–transition temperature correspondence for CuInP2S6. Blue circles represent the current experimental data on stoichiometric deviations, with positive δ values corresponding to In enrichment and negative δ values to Cu enrichment. Green circles represent the present uniaxial pressure data, plotted using the equivalent-pressure scale on the right-hand axis. Red squares show literature composition-dependent data from Ref. [13], with transition temperatures shifted by +9.4 K to align the Cu0.99In1.05P2.04S6 reference composition (TC = 307.6 K) with the transition temperature of the present gas transport-grown reference crystal (TC = 317 K). The solid green line illustrates the phenomenological correspondence between stoichiometric deviations and equivalent mechanical pressure. This comparison does not imply strict thermodynamic equivalence between chemical and externally applied pressure.

3.3. Raman Spectroscopy Results

Room-temperature Raman spectra of CuInP2S6 crystals grown by different methods and with controlled deviations from stoichiometry are compared in Figure 8. The spectra extend from below 50 cm−1 to approximately 600 cm−1, encompassing both low-frequency lattice and cation-related modes and higher-frequency internal vibrations of the P2S6 units. For the comparison of relative spectral intensities, all spectra were normalized to the intensity of the prominent P–P-related Raman band and were subsequently vertically offset for clarity. All four samples retain the characteristic vibrational fingerprint of CuInP2S6 reported previously [23], indicating that the principal structural framework is preserved. At the same time, reproducible differences in the relative intensities, linewidths, and positions of several bands demonstrate that the lattice dynamics are sensitive to both growth conditions and cation stoichiometry.

Figure 8.

Figure 8

Room-temperature Raman spectra of CuInP2S6 crystals: 1—Cu-enriched CuInP2S6 + Cu2S; 2—In-enriched CuInP2S6 + In2S3; 3—Bridgman–Stockbarger growth; 4—gas transport growth. Spectra were normalized to the P–P-related band and vertically offset for clarity; mode assignments for sample 4 follow Ref. [23].

According to the mode assignments established in Ref. [23], the low-frequency part of the spectrum is dominated by lattice and framework vibrations involving Cu- and In-related displacements together with deformations of the sulfur coordination polyhedra, whereas the higher-frequency region contains predominantly internal vibrations of the P2S6 units. The spectra below approximately 200 cm−1 contain several well-resolved features whose relative intensities, widths, and positions differ among the four samples. Because these modes involve the cation sublattices and relatively soft framework deformations, their sensitivity to composition and growth conditions provides direct evidence that the local cation environment and the low-energy lattice dynamics are modified by stoichiometry.

Clear composition-dependent differences are also observed in the intermediate-frequency region. In particular, the relative intensities, positions, and mode-dependent linewidths of the bands in the approximately 250–350 cm−1 range vary among the samples. The In-enriched crystal shows a pronounced redistribution of spectral weight in this region together with small frequency shifts, consistent with the chemically heterogeneous CIPS/IPS state and its associated local strain and modified cation–framework coupling. The Cu-enriched crystal exhibits a different spectral profile, indicating that excess Cu modifies the local potential landscape and cation–framework interactions in a distinct manner.

At higher frequencies, the strong bands associated predominantly with internal vibrations of the P2S6 structural units remain present in all four samples. The prominent P–P-related band near 375 cm−1 and the P–S-related features in the approximately 450–600 cm−1 region [23,24] therefore confirm that the basic anionic framework remains intact. Because the spectra were normalized to the P–P-related band, the observed changes in the other modes represent a redistribution of Raman intensity relative to this internal structural reference. The comparatively stronger changes in the low- and intermediate-frequency regions indicate that stoichiometry primarily perturbs the softer cation- and framework-related degrees of freedom, rather than reconstructing the P2S6 units.

Pressure-dependent Raman studies at substantially higher, multi-GPa pressures reveal a complex and non-monotonic evolution of the CIPS vibrational spectrum [33]. Those pressure regimes lie far outside the low-pressure range relevant to the present pressure–stoichiometry comparison, and the Raman spectra are therefore not used here to assign a quantitative equivalent mechanical pressure to a particular composition. Instead, they provide an independent probe showing that stoichiometric modification affects the low-energy cation–lattice degrees of freedom that are central to the ferrielectric instability.

Quantitative fitting confirms the composition-dependent changes visible in Figure 8. Relative to the gas transport reference, small but systematic frequency shifts are observed in the compositionally modified crystals. The P–P-related band shifts from 374.69 cm−1 in the gas transport crystal to 374.01 cm−1 in the Cu-enriched sample and 373.67 cm−1 in the In-enriched sample. A similar trend is observed for the high-frequency band near 558 cm−1, which shifts from 557.68 cm−1 to 557.09 and 556.30 cm−1, respectively. Pronounced changes also occur in relative spectral weight: the band near 317 cm−1 increases from I/IP–P = 0.364 in the gas transport crystal to 0.439 in the Cu-enriched sample, while the In-enriched sample exhibits the strongest relative intensity of the band near 264 cm−1 (I/IP–P = 0.789, compared with 0.729 for the gas transport crystal). Linewidth changes are mode-dependent rather than uniform; for example, the band near 558 cm−1 broadens from 8.09 cm−1 in the gas transport crystal to 9.43 cm−1 in the In-enriched sample. The complete quantitative comparison of peak positions, normalized intensities, and FWHM values is provided in Table S1 of the Supplementary Materials.

Taken together, the Raman data provide an independent microscopic link between stoichiometry and the Cu-ion/lattice dynamics of CIPS. The composition-dependent shift of the ferrielectric transition is accompanied by systematic modifications of low-energy modes associated with cation displacement and framework deformation, while the internal P2S6 vibrational framework remains largely preserved. Combined with the dielectric and theoretical results, these observations support a common microscopic picture in which stoichiometry modifies the Cu-ion configurational landscape, local strain, and interlayer coupling. The pressure analogy remains phenomenological: Raman spectroscopy identifies changes in the relevant lattice degrees of freedom, but does not by itself establish a quantitative pressure equivalence.

4. Microscopic Interpretation and First-Principles Support

4.1. Cu-Ion Energy Landscape and the Stoichiometry–Pressure Correspondence

The experimental results presented above can be understood within a common microscopic picture in which the ferrielectric state of CuInP2S6 is governed by the occupation and redistribution of Cu ions among several nonequivalent positions, together with the counter-displacement of the In sublattice. Electron-diffraction measurements show that the probability distribution of Cu becomes progressively more symmetric on heating through the ferrielectric transition, while a small but finite population of interlayer tetrahedral Cu sites appears at higher temperatures [11]. Thus, the transition is intrinsically connected with a multi-site, multiwell Cu-ion energy landscape rather than with a single displacive coordinate.

Microscopic descriptions based on local multiwell potentials and coupled cation–lattice degrees of freedom have been developed for thiophosphate ferroelectrics [34,35] and, more specifically, for CIPS within a mixed Ising-type description [36]. These approaches emphasize that relatively small changes in local bonding, interlayer coupling, or site energies can redistribute the statistical occupation of competing Cu positions. Pressure studies of related thiophosphates likewise demonstrate that the polar state is highly sensitive to changes in bond character and lattice geometry [19,37]. For the present work, however, the experimentally relevant variables are the Cu-site energy landscape and interlayer coupling, because both are directly affected by external stress and by composition-dependent internal strain.

A particularly useful phenomenological framework was developed by Morozovska et al. [38] using an eighth-order Landau–Ginzburg–Devonshire (LGD) expansion for CIPS. Importantly, the pressure-dependent dielectric data used to parameterize this model included the earlier measurements of compositionally modified and uniaxially compressed CuInP2S6 crystals reported in our FM&NT-2020 work [39]. In the homogeneous, zero-field limit, the stress-dependent part of the reconstructed free-energy density can be written in the form

gLGD=αT(T−TC)2−σiQi3P32+β4−σiZi33P34+γ6P36+δ8P38

where P3 is the polarization component normal to the layers, σi denotes the applied stress components (Voigt notation), and Qi3 and Zi33 are the linear and nonlinear electrostriction coefficients, respectively [38]. The inclusion of the eighth-order term is essential for reproducing the multiwell thermodynamic potential and the experimentally observed pressure dependence of CIPS. Both sets of coefficients are strongly temperature-dependent and possess unconventional (partly inverted) signs that are characteristic of CIPS (see Supplementary Materials Section S3). In particular, the longitudinal linear coefficient Q33 is negative over a wide temperature range, which accounts for the experimentally observed negative piezoelectric coefficient d33 of bulk CIPS. The nonlinear coefficients Zi33 are essential for reproducing the multiwell thermodynamic potential and the experimentally observed pressure dependence of the transition temperature. Their inclusion allows intermediate negative (tensile) pressure to render the competing potential wells shallow and nearly equal in energy, producing an almost flat free-energy profile. Such a flattened multiwell landscape is fully consistent with the experimental signatures observed for Cu enrichment: reduced TC, enhanced dielectric loss, Raman evidence of modified low-frequency cation–lattice dynamics, and the fragmented, weakly correlated domain state revealed by PFM. In this regime the energetic barriers between competing Cu-site configurations are lowered, increasing the configurational freedom of Cu ions and reducing the energetic preference for long-range ferrielectric order. Conversely, the response of the In-enriched crystals maps onto the positive-pressure side of the same landscape. Lattice mismatch within the CIPS/IPS chemical heterostructure generates compressive strain in the CIPS regions, deepening the polar wells, raising TC and favoring a more rigid, strongly biased domain configuration. Thus, the entire experimental series—from Cu-enriched (negative-pressure-like) through near-stoichiometric gas transport to In-enriched (positive-pressure-like)—can be placed on a single continuous axis of the multiwell LGD potential controlled by the effective interlayer strain and Cu-site energetics. The correspondence remains phenomenological rather than strictly thermodynamic, because stoichiometric variation simultaneously alters local chemistry, defect density and, in the In-rich limit, the CIPS/IPS phase fraction. Nevertheless, both chemical and mechanical control parameters act on the same microscopic degrees of freedom.

4.2. First-Principles Calculations

To examine how weakened interlayer coupling affects the local electronic and vibrational structure, first-principles calculations were performed for bulk CIPS and for a single-layer (1L) periodic-supercell model. The calculations were based on density functional theory [40,41] as implemented in CASTEP [42]. The exchange–correlation energy was described within the generalized-gradient approximation using the PBE functional [43], and a dispersion correction was included to account for long-range van der Waals interactions [44]. Ultrasoft pseudopotentials were employed [45]. Structural optimization was carried out before property calculations, using a plane-wave cutoff energy of 880 eV and a total-energy convergence criterion of 10−6 eV atom−1. Brillouin-zone integrations used Monkhorst–Pack k-point sampling [46], and vibrational properties were calculated within the finite-displacement approach [47].

The 1L model was generated from the bulk structural unit by introducing a 5 Å vacuum region normal to the natural layers and applying periodic boundary conditions. Because the vacuum-thickness convergence was not examined systematically, this model should be regarded as a qualitative representation of strongly reduced interlayer coupling rather than as a fully isolated monolayer. Its purpose is to identify trends in charge redistribution and lattice dynamics associated with weakening the interlayer environment, rather than to reproduce quantitatively the properties of an isolated CIPS monolayer.

4.3. Bulk–Single-Layer Comparison and Implications for Interlayer Coupling

The Mulliken analysis in Table 2 shows only moderate changes ongoing from the bulk structure to the 1L model, but the direction of the change is systematic; the positive charge associated with Cu and In decreases slightly, while the magnitude of the negative S charge is also reduced. The calculated values therefore indicate a modest redistribution of charge when the interlayer environment is strongly reduced, consistent with the mixed ionic–covalent character of bonding in CIPS.

Table 2.

Average Mulliken charges calculated for bulk and single-layer (1L) CIPS.

Species Bulk CIPS 1L CIPS
Cu 0.288 0.279
In 0.886 0.847
P 0.751 0.750
S −0.446 −0.438

The vibrational frequency distributions provide a clearer fingerprint of the loss of interlayer coupling (Figure 9). Several frequency intervals become narrower in the 1L calculation and individual modes shift, reflecting the strongly reduced interlayer coupling and the relaxation of the 1L periodic model. The changes are not consistent with a simple uniform expansion of all bonds: for example, the calculated monolayer thickness changes from 3.382 to 3.397 Å and the layer thickness parameter from 9.922 to 9.941 Å, whereas the P–P distance remains essentially unchanged (2.250 and 2.249 Å for bulk and 1L, respectively). The calculated response is therefore better described as a redistribution of interatomic interactions caused by the modified interlayer boundary condition.

Figure 9.

Figure 9

Calculated Γ-point vibrational frequency distributions for single-layer (1L, (top)) and bulk (bottom) CuInP2S6. The histogram bin width is Δ = 5 cm−1. In the plotted legends, “w1L” and “W” denote the 1L and bulk calculations, respectively.

The sensitivity of the lattice dynamics to the polar state is independently illustrated by the calculated Raman spectra of bulk CIPS (Figure 10). The ferrielectric and paraelectric structures show pronounced differences in the number, positions, and relative intensities of Raman-active features, confirming that the vibrational spectrum is strongly coupled to the Cu-ion configuration and the associated structural relaxation. This result is consistent with the experimental Raman trends discussed in Section 3.3, where composition-dependent changes are particularly evident in the low-frequency cation/lattice modes and in the intermediate-frequency region involving coupled cation–framework motions.

Figure 10.

Figure 10

Calculated Raman spectra of bulk CuInP2S6 in the ferrielectric (f-CIPS) and paraelectric (p-CIPS) structures. The two spectra are shown using separate intensity axes for clarity; the horizontal axis represents Raman shift in cm−1.

Overall, the LGD and first-principles results support the same physical picture from complementary scales. The phenomenological model [38] shows that negative pressure can flatten the multiwell free-energy landscape, while the 1L calculations demonstrate that weakening the interlayer environment measurably modifies charge redistribution and lattice dynamics. The 1L model should therefore be viewed as a qualitative limiting case of reduced interlayer coupling rather than as a literal representation of either an isolated monolayer or Cu-rich CIPS. Within this interpretation, Cu enrichment moves CIPS toward a softer, negative-pressure-like state, whereas In-rich CIPS/IPS heterostructures generate an internal compressive environment closer to the positive-pressure side. This microscopic framework provides a direct link between stoichiometry, lattice dynamics, and the strongly composition-dependent ferrielectric domain structures discussed in the following section.

5. Stoichiometry- and Growth-Induced Evolution of Domain Structure in CuInP2S6

The pressure–stoichiometry correspondence established from the dielectric and theoretical analyses, together with the Raman evidence for composition-dependent changes in lattice dynamics, is also reflected at the mesoscale in the polar domain structure. Figure 11 compares PFM amplitude and phase images with local switching loops for CuInP2S6 crystals grown by the Bridgman–Stockbarger and gas transport methods and for crystals prepared from Cu2S- and In2S3-enriched starting compositions. All four samples exhibit an approximately 180° PFM phase contrast, consistent with antiparallel out-of-plane polarization states, but the domain size, spatial uniformity, and local switching behavior differ markedly. These differences show that both stoichiometry and the defect landscape introduced during crystal growth strongly influence the organization of the ferrielectric state.

Figure 11.

Figure 11

PFM amplitude (top row) and phase (middle row) images, together with local phase and amplitude switching loops (bottom rows), for CuInP2S6 single crystals: (a,e,i,m) Bridgman–Stockbarger growth; (b,f,j,n) Cu-enriched CuInP2S6 + Cu2S; (c,g,k,o) gas transport growth; and (d,h,l,p) In-enriched CuInP2S6 + In2S3. The phase images show pronounced differences in domain morphology, from large irregular domains in the melt-grown crystal to a comparatively uniform fine-domain pattern in the gas transport sample and a strongly biased domain population in the In-enriched crystal. Scale bars: 5 µm. The red and blue traces in the local switching plots distinguish the two opposite voltage-sweep branches.

5.1. Reference Domain State and Growth-Induced Defect Pinning

Among the investigated samples, the gas transport crystal (Figure 11c,g,k,o) provides the closest practical reference to a near-stoichiometric, weakly defect-pinned state. Its phase image consists of a dense and relatively uniform pattern of well-defined domains with sharp contrast, similar to previously reported PFM observations of CIPS [48]. The local phase loop is comparatively symmetric and exhibits only a small imprint. This behavior is consistent with a lower density of extended growth defects and internal bias fields than in crystals grown from the melt, so that the observed domain morphology is governed more strongly by the intrinsic order–disorder character of CIPS.

The Bridgman–Stockbarger crystal (Figure 11a,e,i,m) shows a distinctly different mesoscale organization. Large, irregular domains coexist with strongly nonuniform PFM amplitude contrast, while the local phase loop remains well developed. This combination suggests that the ferrielectric state itself is robust, but that domain-wall positions are strongly influenced by extended structural inhomogeneities created during melt growth. The local switching loop probes only a nanoscale region beneath the tip; consequently, a locally symmetric loop can coexist with pronounced large-scale pinning visible in the domain image.

The AFM topography in Figure 12 provides direct evidence for such structural heterogeneity. A discontinuity of the upper surface layer exposes an underlying region containing elongated topographic features with a different orientation. Because adjacent CIPS layers are coupled by comparatively weak van der Waals interactions, growth features and defect lines need not remain perfectly registered from one layer to the next. The resulting three-dimensional strain and defect landscape can therefore act as a network of preferential pinning sites for domain walls, explaining the large but irregular domains observed in the Bridgman–Stockbarger sample.

Figure 12.

Figure 12

Three-dimensional AFM topography of a Bridgman–Stockbarger-grown CuInP2S6 crystal showing a discontinuity of the upper surface layer and differently oriented elongated features in the underlying region. The weak interlayer coupling allows growth-related structural inhomogeneities to vary between adjacent layers, producing a spatially heterogeneous pinning landscape. The color gradient represents the surface height, with lighter colors corresponding to higher regions and darker colors to lower regions.

It should be noted that the Bridgman–Stockbarger crystal is simultaneously Cu-rich according to EDS (Table 1) and contains extended growth-induced structural inhomogeneities. The lowered transition temperature (307 K) is therefore consistent with a negative-pressure-like stoichiometric contribution, while the large, irregular domains and strong spatial nonuniformity of the PFM amplitude reflect additional domain-wall pinning by the three-dimensional defect landscape created during melt growth. These two contributions—the thermodynamic softening of the Cu-ion energy landscape and defect-mediated pinning—act concurrently and cannot be fully separated in the present data.

5.2. Stoichiometry-Driven Evolution of Domain Morphology and Switching

Cu enrichment produces a different type of domain disorder (Figure 11b,f,j,n). The phase pattern becomes more spatially heterogeneous, with irregular and locally discontinuous domain boundaries. Quantitatively, however, the local switching loop remains nearly centered (Vimprint ≈ −0.2 V) while the local switching half-width decreases markedly to approximately 2.0 V, compared with approximately 4.6 V for the gas transport and Bridgman–Stockbarger crystals. This reduction in the characteristic local switching bias is consistent with a softer, negative-pressure-like Cu-ion energy landscape. The reduction in TC and the smaller switching half-width indicate a lower energetic separation between competing local polar configurations, while the fragmented domain morphology reflects the increased sensitivity of the polar state to local Cu-ion reconfiguration and random internal fields.

The Cu-enriched CIPS crystals offer a potentially useful route toward reducing the operating voltage of ferrielectric devices. In particular, the substantially smaller local switching half-width (approximately 2.0 V compared with 4.6 V for the near-stoichiometric reference) indicates that Cu enrichment can facilitate polarization reversal, which may be advantageous for low-voltage non-volatile memory and neuromorphic devices. However, this benefit is accompanied by increased dielectric losses, a more fragmented domain structure, and a reduction in the transition temperature to 312 K. These effects may adversely influence leakage currents, polarization retention, and the temperature range of stable device operation. Therefore, Cu enrichment should be considered a means of balancing switching accessibility against polar-state stability rather than an unconditionally beneficial modification. The present results identify this trade-off at the materials level, while direct measurements of device retention, endurance, and switching energy will be necessary to establish the optimal composition for practical applications.

The In-enriched sample (Figure 11d,h,l,p) exhibits the opposite limiting behavior. The phase image is dominated by one polarization orientation, with only sparse regions of opposite contrast, and the local phase loop shows a pronounced bias.

The quantitative PFM analysis reinforces this interpretation. The In-enriched sample exhibits Vsw− ≈ +0.1 V and Vsw+ ≈ +3.5 V, corresponding to a local switching half-width of approximately 1.7 V and a pronounced positive imprint of approximately +1.8 V. In addition, one of the two dominant phase-contrast states occupies approximately 92% of the analyzed area (phase-state population ≈ 92:8), compared with an almost balanced 48:52 population in the gas transport crystal. This strong bias in both the switching loop and the phase-state population provides quantitative evidence for a pinned internal-field state in the In-rich CIPS/IPS system.

A related strongly asymmetric domain population was reported for CIPS/In4/3P2S6 heterostructures with compositionally segregated chemical domains [13], although the detailed domain morphology is also sensitive to thermal history. The present response is consistent with In4/3P2S6-rich chemical regions, which are known to generate compressive strain in the CIPS component and therefore an effective positive chemical pressure [13,14,15]. The corresponding increase in TC and the stabilization of the polar free-energy minima favor a more rigid polarization configuration and stronger domain pinning. Thus, In enrichment stabilizes the ferrielectric state thermodynamically while simultaneously reducing the configurational freedom of the domain pattern.

5.3. Unified Picture of Composition, Growth Defects, and Domain Organization

The PFM results reveal two complementary and partially coupled mechanisms controlling the domain structure of CIPS. Stoichiometric deviation modifies the thermodynamic landscape through composition-dependent strain, Cu-site occupancy, and interlayer coupling. Cu enrichment moves the system toward a softer negative-pressure-like regime, whereas the In-enriched response is consistent with a positive chemical pressure contribution associated with CIPS/IPS phase segregation. The growth route, however, independently contributes through the density and spatial distribution of extended defects, internal fields, and domain-wall pinning centers. Because composition and synthesis conditions are not fully orthogonal variables in the present sample set, these contributions cannot be quantitatively separated in all cases, particularly for the Bridgman–Stockbarger crystal.

These mechanisms are not independent. A local change in the Cu-ion potential landscape determines how readily a polar region can reconfigure, whereas growth defects and chemical interfaces determine where such reconfiguration is spatially favored or inhibited. The resulting domain morphology is therefore a mesoscale manifestation of the same microscopic variables that control the dielectric anomaly and Raman response: Cu-ion configurational freedom, interlayer coupling, strain, and defect-mediated pinning. This correspondence links the structural, dielectric, vibrational, and PFM observations within a single physical picture and provides the basis for the conclusions drawn below.

The observed differences in domain morphology are consistent with the unconventional switching dynamics of CIPS, in which polarization reversal is mediated primarily by single Cu-dipole flips rather than by classical domain wall motion. Consequently, local changes in the Cu-ion energy landscape (induced by stoichiometry or growth defects) strongly influence both the mobility of polar regions and the effectiveness of pinning centers. The quantitative switching and phase-state parameters are summarized in Table 3.

Table 3.

Quantitative parameters extracted from local PFM switching loops and phase images of the investigated CuInP2S6 crystals. Vsw− and Vsw+ denote the negative- and positive-branch local switching thresholds, respectively, determined from the minima of the PFM amplitude loops. The local switching half-width and imprint voltage were calculated as Vc* = (Vsw+ − Vsw−)/2 and Vimprint = (Vsw+ + Vsw−)/2, respectively. The phase-state population represents the relative area occupied by the two dominant PFM phase-contrast states; the absolute sign of the polarization is not assigned from the color contrast alone.

Sample Vsw− (V) Vsw+ (V) Vc* (V) Vimprint (V) Phase-State
Population A:B
Bridgman–Stockbarger ≈−4.7 ≈+4.6 ≈4.6 ≈−0.1 ≈56:44
Cu-enriched ≈−2.2 ≈+1.7 ≈2.0 ≈−0.2 ≈57:43
Gas transport ≈−4.7 ≈+4.5 ≈4.6 ≈−0.1 ≈48:52
In-enriched ≈+0.1 ≈+3.5 ≈1.7 ≈+1.8 ≈92:8

The observed differences in domain morphology are also consistent with the multi-pathway nature of Cu-ion dynamics in CIPS. Cu-ion migration proceeds via two distinct channels: low-barrier intralayer hopping (primarily responsible for polarization switching) and higher-barrier interlayer hopping across the van der Waals gap (responsible for long-range ionic conductivity). Density functional calculations yield characteristic migration barriers of approximately 0.05 eV for intralayer Cu1–Cu2 hopping, 0.7 eV for the polar Cu1u–Cu1d flip, and 1.1 eV for interlayer migration [49]. Experimental activation energies extracted from ionic conductivity (0.6–0.7 eV) are consistent with the higher of the intralayer barriers and a partial contribution of interlayer processes [4,32]. Stoichiometric deviations and growth-induced defects modify the relative accessibility of these pathways, thereby coupling the Cu-ion configurational landscape to the observed shifts in TC, dielectric response and domain morphology.

From an application perspective, the ability to tune local switching thresholds, imprint, and domain state stability through stoichiometry and growth conditions is directly relevant to non-volatile ferroelectric memory. Recent work has demonstrated non-volatile polarization switching in CIPS enabled by imprint field engineering [50], while CIPS-containing hybrid ferroelectrics have been used to realize ambipolar non-volatile MoS2 memory transistors [51]. Although retention and endurance are not measured in the present study, our results identify stoichiometry- and growth-controlled internal bias, switching energetics, and domain pinning as additional materials-level parameters for tailoring CIPS-based memory functionality.

6. Conclusions

The present study demonstrates that the ferrielectric properties of CuInP2S6 are highly sensitive to both deviations from stoichiometry and the defect landscape introduced by crystal growth conditions. Thus, the composition and synthesis route should be regarded as coupled but distinct control parameters rather than as interchangeable origins of the observed behavior. Their combined control of transition temperature, local switching bias, and domain pinning is particularly relevant for the materials-level optimization of CIPS-based non-volatile devices. The systematic comparison of Bridgman–Stockbarger, gas transport, Cu-enriched and In-enriched crystals reveals consistent shifts in transition temperature, dielectric response and mesoscale domain morphology. These observations are unified by a common microscopic picture based on composition- and growth-dependent changes in Cu-ion configurational freedom, interlayer coupling, strain and defect-mediated pinning. In enrichment shifts the ferrielectric transition to higher temperature and is consistent with the formation of CIPS/In4/3P2S6 chemical heterostructures. The associated lattice mismatch produces an effective positive chemical pressure on the CIPS regions, stabilizing the polar state and favoring a rigid, strongly biased domain configuration. Cu enrichment produces the opposite trend: lower TC, enhanced dielectric loss and a more fragmented domain state, all of which are characteristic of a negative-pressure-like softening of the Cu-ion energy landscape. This stoichiometry–pressure correspondence is supported by uniaxial pressure measurements, the multiwell Landau–Ginzburg–Devonshire description and first-principles comparisons of bulk and weakly coupled single-layer CIPS. The analogy is phenomenological rather than strictly thermodynamic, yet both chemical and mechanical control parameters act on the same underlying degrees of freedom associated with Cu-ion configuration and interlayer interactions. Crystal growth conditions provide an independent control parameter. Gas transport crystals exhibit the most uniform domain organization and the smallest local imprint, whereas melt-grown crystals contain extended structural inhomogeneities that strongly influence domain wall pinning. Consequently, the observed PFM morphology is a mesoscale manifestation of the combined thermodynamic and defect landscapes. Overall, the results establish stoichiometry, internal chemical pressure and growth-induced defects as interconnected and experimentally accessible tools for tuning ferrielectric order in CuInP2S6. The demonstrated ability to systematically change the transition temperature, dielectric losses and domain morphology through stoichiometry and growth conditions offers a practical route toward optimizing CIPS for memristive, neuromorphic and non-volatile memory applications, where controlled Cu-ion dynamics and stable polar domain configurations are decisive for device performance and reliability.

Acknowledgments

During the preparation of this manuscript, the authors used ChatGPT (OpenAI, GPT-5.6) and Grammarly v.1.2.300.1965 for language editing, restructuring, drafting support, grammar correction, and improving readability. All scientific interpretations, numerical results, data selection, and conclusions were critically reviewed and verified by the authors, who take full responsibility for the content of the publication.

Supplementary Materials

The following supporting information can be downloaded at: https://www.mdpi.com/article/10.3390/nano16211336/s1, Section S1: EDS Data; Figure S1: Representative SEM surface image and local EDS analysis (elemental quantification and spectrum) for gas-transport CIPS; Figure S2: Representative SEM surface image and local EDS analysis (elemental quantification and spectrum) for Bridgman–Stockbarger CIPS; Figure S3: Representative SEM surface image and local EDS analysis (elemental quantification and spectrum) for Cu-enriched CuInP2S6 + Cu2S; Figure S4: Representative SEM surface image and local EDS analysis (elemental quantification and spectrum) for In-enriched CuInP2S6 + In2S3. Pronounced domain-like contrast is visible in the SEM image, similar to the chemical-domain morphology reported in Ref. [13] of the main text. The quantitative EDS values correspond to a single representative analyzed area and should not be interpreted as the averaged composition of the sample; Section S2: Complete Dielectric Spectra; Figure S5: Temperature–frequency dependences of (a) the real (ε′) and (b) the imaginary (ε″) components of the complex dielectric permittivity (ε* =ε′ − iε″) for a Bridgman–Stockbarger-grown CuInP2S6 crystal; Figure S6: Temperature–frequency dependences of (a) the real (ε′) and (b) the imaginary (ε″) components of the complex dielectric permittivity (ε* = ε′ − iε″) for a Cu-enriched CuInP2S6 + Cu2S crystal grown by chemical vapor transport (CVT); Figure S7: Temperature–frequency dependences of (a) the real (ε′) and (b) the imaginary (ε″) components of the complex dielectric permittivity (ε* = ε′ − iε″) for a gas-transport-grown CuInP2S6 crystal; Figure S8: Temperature–frequency dependences of (a) the real (ε′) and (b) the imaginary (ε″) components of the complex dielectric permittivity (ε* = ε′ − iε″) for an In-enriched CuInP2S6 + In2S3 crystal grown by chemical vapor transport (CVT); Section S3: Landau–Ginzburg–Devonshire electrostriction coefficients of CuInP2S6. Temperature-dependent linear and nonlinear electrostriction coefficients used in the LGD analysis, together with a comparison to experimental data [52]; Section S4: Quantitative Raman parameters; Table S1: Quantitative Raman parameters. Each cell is reported as peak position ν (cm−1)/normalized intensity I/IP–P/FWHM (cm−1).

Author Contributions

Conceptualization, A.M.; methodology, D.G., S.L., I.R., M.V., L.P., A.K., N.D., K.G. and A.M.; formal analysis, K.G. and A.M.; investigation, D.G., S.L., I.R., M.V., L.P. and A.M.; data curation, D.G. and A.M.; visualization, D.G., K.G. and A.M.; writing—original draft preparation, A.M.; writing—review and editing, all authors; supervision, A.M. All authors have read and agreed to the published version of the manuscript.

Data Availability Statement

The data presented in this study are available within the article and its Supplementary Materials. Additional datasets are available from the corresponding author upon reasonable request.

Conflicts of Interest

The authors declare no conflicts of interest.

Funding Statement

This research was funded by the Ministry of Education and Science of Ukraine (Research Work No. 0124U004302—PH/41-2024; state-budget projects Nos. 0125U001555 and 0126U001941), the European Union’s Horizon Europe Marie Skłodowska-Curie Staff Exchanges program (Grant No. 101131229—Piezo2D), and project TKP2021-NVA-04. Additional support was provided by the Bolyai János Research Scholarship of the Hungarian Academy of Sciences.

Footnotes

Disclaimer/Publisher’s Note: The statements, opinions and data contained in all publications are solely those of the individual author(s) and contributor(s) and not of MDPI and/or the editor(s). MDPI and/or the editor(s) disclaim responsibility for any injury to people or property resulting from any ideas, methods, instructions or products referred to in the content.

References

  • 1.Susner M.A., Chyasnavichyus M., McGuire M.A., Ganesh P., Maksymovych P. Metal Thio- and Selenophosphates as Multifunctional van der Waals Layered Materials. Adv. Mater. 2017;29:1602852. doi: 10.1002/adma.201602852. [DOI] [PubMed] [Google Scholar]
  • 2.Wang F.M., Shifa T.A., Yu P., He P., Liu Y., Wang F., Wang Z., Zhan X., Lou X., Xia F., et al. New Frontiers on van der Waals Layered Metal Phosphorous Trichalcogenides. Adv. Funct. Mater. 2018;28:1802151. doi: 10.1002/adfm.201802151. [DOI] [Google Scholar]
  • 3.Liu F., You L., Seyler K.L., Li X., Yu P., Lin J., Wang X., Zhou J., Wang H., He H., et al. Room-temperature ferroelectricity in CuInP2S6 ultrathin flakes. Nat. Commun. 2016;7:12357. doi: 10.1038/ncomms12357. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 4.Zhou S., You L., Zhou H., Pu Y., Gui Z., Wang J. Van der Waals layered ferroelectric CuInP2S6: Physical properties and device applications. Front. Phys. 2021;16:13301. doi: 10.1007/s11467-020-0986-0. [DOI] [Google Scholar]
  • 5.Ghani M.A., Sarkar S., Li Y., Wang Y., Watanabe K., Taniguchi T., Wang Y., Chhowalla M. Ferroelectric field effect transistors based on two-dimensional CuInP2S6 (CIPS) and graphene heterostructures. MRS Energy Sustain. 2024;11:616–623. doi: 10.1557/s43581-024-00109-y. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 6.Zhao L., Liang Y., Ma J., Pan Z., Liu X., Yang M., Sun Y., Gao W., Li B., Li J., et al. Ultra-Steep-Slope and High-Stability of CuInP2S6/WS2 Ferroelectric Negative Capacitor Transistors by Passivation Effect and Dual-Gate Modulation. Adv. Funct. Mater. 2023;33:2306708. doi: 10.1002/adfm.202306708. [DOI] [Google Scholar]
  • 7.Liu Y., Wu Y., Wang B., Chen H., Yi D., Liu K., Nan C.W., Ma J. Versatile memristor implemented in van der Waals CuInP2S6. Nano Res. 2023;16:10191–10197. doi: 10.1007/s12274-023-5583-4. [DOI] [Google Scholar]
  • 8.Peng J., Zou G., Huo J., Li Z., Sun T., Feng B., Du C., Huo J., Liu L. Robust Neuromorphic Computing Enabled by Femtosecond Laser-Modulated Divergent Ion Dynamics in CuInP2S6. Adv. Funct. Mater. 2025;35:2504334. doi: 10.1002/adfm.202504334. [DOI] [Google Scholar]
  • 9.Wang Z., Li J., Fan X., Tang W., Zhu H., Li L. CuInP2S6 Heterojunction Based Visible Range Optoelectronic Synapse With Femtojoule Energy Consumption. Adv. Mater. Technol. 2025;10:2401589. doi: 10.1002/admt.202401589. [DOI] [Google Scholar]
  • 10.Maisonneuve V., Evain M., Payen C., Cajipe V.B., Molinié P. Room-temperature crystal structure of the layered phase CuInP2S6. J. Alloys Compd. 1995;218:157–164. doi: 10.1016/0925-8388(94)01416-7. [DOI] [Google Scholar]
  • 11.Maisonneuve V., Cajipe V.B., Simon A., von der Muhll R., Ravez J. Ferrielectric ordering in lamellar CuInP2S6. Phys. Rev. B. 1997;56:10860–10868. doi: 10.1103/PhysRevB.56.10860. [DOI] [Google Scholar]
  • 12.Dziaugys A., Banys J., Vysochanskii Y. Broadband dielectric investigations of indium rich CuInP2S6 layered crystals. Z. Krist. 2011;226:171–176. doi: 10.1524/zkri.2011.1323. [DOI] [Google Scholar]
  • 13.Susner M.A., Chyasnavichyus M., Puretzky A.A., He Q., Conner B.S., Ren Y., Cullen D.A., Ganesh P., Shin D., Demir H., et al. Cation–Eutectic Transition via Sublattice Melting in CuInP2S6/In4/3P2S6 van der Waals Layered Crystals. ACS Nano. 2017;11:7060–7073. doi: 10.1021/acsnano.7b02695. [DOI] [PubMed] [Google Scholar]
  • 14.Susner M.A., Belianinov A., Borisevich A., He Q., Chyasnavichyus M., Demir H., Sholl D.S., Ganesh P., Abernathy D.L., McGuire M.A., et al. High-TC Layered Ferrielectric Crystals by Coherent Spinodal Decomposition. ACS Nano. 2015;9:12365–12373. doi: 10.1021/acsnano.5b05682. [DOI] [PubMed] [Google Scholar]
  • 15.Rao R., Selhorst R., Jiang J., Conner B.S., Siebenaller R., Rowe E., Giordano A.N., Pachter R., Susner M.A. Investigating Strain between Phase-Segregated Domains in Cu-Deficient CuInP2S6. Chem. Mater. 2023;35:8020–8029. doi: 10.1021/acs.chemmater.3c01238. [DOI] [Google Scholar]
  • 16.Checa M., Jin X., Millan-Solsona R., Neumayer S.M., Susner M.A., McGuire M.A., O’Hara A., Gomila G., Maksymovych P., Pantelides S.T., et al. Revealing Fast Cu-Ion Transport and Enhanced Conductivity at the CuInP2S6–In4/3P2S6 Heterointerface. ACS Nano. 2022;16:15347–15357. doi: 10.1021/acsnano.2c06992. [DOI] [PubMed] [Google Scholar]
  • 17.Grzechnik A., Cajipe V.B., Payen C., McMillan P.F. Pressure-induced phase transition in ferrielectric CuInP2S6. Solid State Commun. 1998;108:43–47. doi: 10.1016/S0038-1098(98)00297-X. [DOI] [Google Scholar]
  • 18.Shusta V.S., Prits I.P., Guranich P.P., Gerzanich E.I., Slivka A.G. Dielectric properties of CuInP2S6 crystals under high pressure. Condens. Matter Phys. 2007;10:91–94. doi: 10.5488/CMP.10.1.91. [DOI] [Google Scholar]
  • 19.Guranich P., Shusta V., Gerzanich E., Slivka A., Kuritsa I., Gomonnai O. Influence of hydrostatic pressure on the dielectric properties of CuInP2S6 and CuInP2Se6 layered crystals. J. Phys. Conf. Ser. 2007;79:012009. doi: 10.1088/1742-6596/79/1/012009. [DOI] [Google Scholar]
  • 20.Shusta O.V., Slivka A.G., Kedylich V.M., Guranich P.P., Shusta V.S., Gerzanich E.I., Prits I.P. Effect of Uniaxial Pressure on the Dielectric Properties of CuInP2S6 Crystals. Sci. Bull. Uzhhorod Univ. Ser. Phys. 2010;28:44–46. doi: 10.24144/2415-8038.2010.28.44-46. [DOI] [Google Scholar]
  • 21.Yao X., Bai Y., Jin C., Zhang X., Zheng Q., Xu Z., Chen L., Wang S., Liu Y., Wang J., et al. Anomalous polarization enhancement in a van der Waals ferroelectric material under pressure. Nat. Commun. 2023;14:4301. doi: 10.1038/s41467-023-40075-6. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 22.Bu K., Fu T., Du Z., Feng X., Wang D., Li Z., Guo S., Sun Z., Luo H., Liu G., et al. Enhanced Second-Harmonic Generation of van der Waals CuInP2S6 via Pressure-Regulated Cationic Displacement. Chem. Mater. 2023;35:242–250. doi: 10.1021/acs.chemmater.2c03066. [DOI] [Google Scholar]
  • 23.Vysochanskii Y.M., Stephanovich V.A., Molnar A.A., Cajipe V.B., Bourdon X. Raman spectroscopy study of the ferroelectric-paraelectric transition in layered CuInP2S6. Phys. Rev. B. 1998;58:9119–9124. doi: 10.1103/PhysRevB.58.9119. [DOI] [Google Scholar]
  • 24.Zhou Z., Zhang J.-J., Turner G.F., Moggach S.A., Lekina Y., Morris S., Wang S., Hu Y., Li Q., Xue J., et al. Sliding-mediated ferroelectric phase transition in CuInP2S6 under pressure. Appl. Phys. Rev. 2024;11:011414. doi: 10.1063/5.0177451. [DOI] [Google Scholar]
  • 25.Nitsche R., Wild P. Crystal growth of metal-phosphorus-sulfur compounds by vapor transport. Mater. Res. Bull. 1970;5:419–423. doi: 10.1016/0025-5408(70)90080-2. [DOI] [Google Scholar]
  • 26.Nitsche R. Crystal chemistry, growth and properties of multi-cation chalcogenides. J. Phys. Colloq. 1975;36:9–15. doi: 10.1051/jphyscol:1975302. [DOI] [Google Scholar]
  • 27.Prits I.P., Mayor M.M., Vysochanskii Y.M., Molnar A.A., Gurzan M.I., Korda N.F. Preparation of CuInP2S6 Single Crystals by Chemical Vapour Transport Reactions and Directional Crystallisation from the Melt and Their Ferroelectric Properties; Proceedings of the 8th International Symposium High-Purity Metallic and Semiconductor Materials; Kharkiv, Ukraine. 22–27 April 2002; pp. 103–105. (In Russian) [Google Scholar]
  • 28.Molnar A.A. Temperature Controller for an Immersion-Type Cryostat. Uzhhorod Univ. Sci. Her. Ser. Phys. 2016;40:148–156. doi: 10.24144/2415-8038.2016.40.148-156. [DOI] [Google Scholar]
  • 29.Bán H., Gál D., Gerasimov V., Haysak A., Molnar A. Proceedings of the 11th IEEE International Conference on Intelligent Data Acquisition and Advanced Computing Systems: Technology and Applications (IDAACS), Cracow, Poland, 22–25 September 2021. IEEE; Piscataway, NJ, USA: 2021. Automated Measuring System for Studying the Temperature Dependence of Dielectric Spectra of Ferroelectrics; pp. 156–159. [DOI] [Google Scholar]
  • 30.Novoselov K.S., Geim A.K., Morozov S.V., Jiang D., Zhang Y., Dubonos S.V., Grigorieva I.V., Firsov A.A. Electric Field Effect in Atomically Thin Carbon Films. Science. 2004;306:666–669. doi: 10.1126/science.1102896. [DOI] [PubMed] [Google Scholar]
  • 31.Nečas D., Klapetek P. Gwyddion: An open-source software for SPM data analysis. Cent. Eur. J. Phys. 2012;10:181–188. doi: 10.2478/s11534-011-0096-2. [DOI] [Google Scholar]
  • 32.Maisonneuve V., Reau J.M., Dong M., Cajipe V.B., Payen C., Ravez J. Ionic conductivity in ferroic CuInP2S6 and CuCrP2S6. Ferroelectrics. 1997;196:257–260. doi: 10.1080/00150199708224175. [DOI] [Google Scholar]
  • 33.Rao R., Conner B.S., Jiang J., Pachter R., Susner M.A. Raman spectroscopy study of pressure-induced phase transitions in single crystal CuInP2S6. J. Chem. Phys. 2023;159:224706. doi: 10.1063/5.0162002. [DOI] [PubMed] [Google Scholar]
  • 34.Yevych R., Medulych M., Vysochanskii Y. Nonlinear Dynamics of Ferroelectrics with Three-Well Local Potential. Condens. Matter Phys. 2018;21:23001. doi: 10.5488/CMP.21.23001. [DOI] [Google Scholar]
  • 35.Banys J., Dziaugys A., Glukhov K.E., Morozovska A.N., Morozovsky N.V., Vysochanskii Y.M. Van der Waals Ferroelectrics: Properties and Device Applications of Phosphorous Chalcogenides. Wiley-VCH; Weinheim, Germany: 2022. [DOI] [Google Scholar]
  • 36.Yevych R., Liubachko V., Hryts V., Medulych M., Kohutych A., Vysochanskii Y. Description of CuInP2S6 ferrielectrics in a mixed Ising model. Condens. Matter Phys. 2024;27:14701. doi: 10.5488/CMP.27.14701. [DOI] [Google Scholar]
  • 37.Ovsyannikov S.V., Morozova N.V., Korobeinikov I.V., Haborets V., Yevych R., Vysochanskii Y., Shchennikov V.V. Tuning the electronic and vibrational properties of Sn2P2Se6 and Pb2P2S6 crystals and their metallization under high pressure. Dalton Trans. 2017;46:4245–4258. doi: 10.1039/C6DT03854A. [DOI] [PubMed] [Google Scholar]
  • 38.Morozovska A.N., Eliseev E.A., Kalinin S.V., Vysochanskii Y.M., Maksymovych P. Stress-induced phase transitions in nanoscale CuInP2S6. Phys. Rev. B. 2021;104:054102. doi: 10.1103/PhysRevB.104.054102. [DOI] [Google Scholar]
  • 39.Molnar A., Glukhov K., Medulych M., Gál D., Bán H., Vysochanskii Y. Proceedings of the Abstract Book of the FM&NT-2020 Online Conference, Virtual Vilnius, Lithuania, 23–26 November 2020. Vilnius University; Vilnius, Lithuania: 2020. The Effect of Changes in Chemical Composition and Uniaxial Compression on the Phase Transition of CuInP2S6 Crystals; p. 108. [Google Scholar]
  • 40.Hohenberg P., Kohn W. Inhomogeneous Electron Gas. Phys. Rev. 1964;136:B864–B871. doi: 10.1103/PhysRev.136.B864. [DOI] [Google Scholar]
  • 41.Kohn W., Sham L.J. Self-Consistent Equations Including Exchange and Correlation Effects. Phys. Rev. 1965;140:A1133–A1138. doi: 10.1103/PhysRev.140.A1133. [DOI] [Google Scholar]
  • 42.Clark S.J., Segall M.D., Pickard C.J., Hasnip P.J., Probert M.I.J., Refson K., Payne M.C. First principles methods using CASTEP. Z. Krist. 2005;220:567–570. doi: 10.1524/zkri.220.5.567.65075. [DOI] [Google Scholar]
  • 43.Perdew J.P., Burke K., Ernzerhof M. Generalized Gradient Approximation Made Simple. Phys. Rev. Lett. 1996;77:3865–3868. doi: 10.1103/PhysRevLett.77.3865. [DOI] [PubMed] [Google Scholar]
  • 44.Grimme S. Semiempirical GGA-Type Density Functional Constructed with a Long-Range Dispersion Correction. J. Comput. Chem. 2006;27:1787–1799. doi: 10.1002/jcc.20495. [DOI] [PubMed] [Google Scholar]
  • 45.Vanderbilt D. Soft self-consistent pseudopotentials in a generalized eigenvalue formalism. Phys. Rev. B. 1990;41:7892–7895. doi: 10.1103/PhysRevB.41.7892. [DOI] [PubMed] [Google Scholar]
  • 46.Monkhorst H.J., Pack J.D. Special points for Brillouin-zone integrations. Phys. Rev. B. 1976;13:5188–5192. doi: 10.1103/PhysRevB.13.5188. [DOI] [Google Scholar]
  • 47.Montanari B., Harrison N.M. Lattice dynamics of TiO2 rutile: Influence of gradient corrections in density functional calculations. Chem. Phys. Lett. 2002;364:528–534. doi: 10.1016/S0009-2614(02)01401-X. [DOI] [Google Scholar]
  • 48.Belianinov A., He Q., Dziaugys A., Maksymovych P., Eliseev E., Borisevich A., Morozovska A., Banys J., Vysochanskii Y., Kalinin S.V. CuInP2S6 Room Temperature Layered Ferroelectric. Nano Lett. 2015;15:3808–3814. doi: 10.1021/acs.nanolett.5b00491. [DOI] [PubMed] [Google Scholar]
  • 49.Jiang X., Zhang X., Deng Z., Deng J., Wang X., Wang X., Yang W. Dual-role ion dynamics in ferroionic CuInP2S6: Revealing the transition from ferroelectric to ionic switching mechanisms. Nat. Commun. 2024;15:10822. doi: 10.1038/s41467-024-55160-7. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 50.Zhang Y., Du S., Liu X., Yuan Y., Jing Y., Tian T., Chu J., Xue F., Chang K., Sun J. Low-force pulse switching of ferroelectric polarization enabled by imprint field. Nat. Commun. 2025;16:5271. doi: 10.1038/s41467-025-60602-x. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 51.Jeong Y., Wang H., Tordi P., Hu Y.C., Tamayo A., Wu B., Ahn H.S., Sofer Z., Jung J.H., Bonini M., et al. Boosting Ferroelectricity: 2D and Polymer Ferroelectric Hybrids Enabling Ambipolar Nonvolatile MoS2 Memory Transistor. Adv. Sci. 2026:e76127. doi: 10.1002/advs.76127. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 52.You L., Zhang Y., Zhou S., Chaturvedi A., Morris S.A., Liu F., Chang L., Ichinose D., Funakubo H., Hu W., et al. Origin of giant negative piezoelectricity in a layered van der Waals ferroelectric. Sci. Adv. 2019;5:eaav3780. doi: 10.1126/sciadv.aav3780. [DOI] [PMC free article] [PubMed] [Google Scholar]

Associated Data

This section collects any data citations, data availability statements, or supplementary materials included in this article.

Supplementary Materials

Data Availability Statement

The data presented in this study are available within the article and its Supplementary Materials. Additional datasets are available from the corresponding author upon reasonable request.


Articles from Nanomaterials are provided here courtesy of Multidisciplinary Digital Publishing Institute (MDPI)

RESOURCES