Skip to main content
Materials logoLink to Materials
. 2026 Nov 7;19(21):4732. doi: 10.3390/ma19214732

CO2 Adsorption and Separation Behavior Research of Polypyrrole Under Higher Pressure

Zhe Wang 1, Zhanhong Li 1, Ting Zhang 1, Zhen Wang 2, Jifu Huang 1, Hang Cao 3, Shupeng Li 1,*
Editors: György Thalmaier, Tamás Mankovits
PMCID: PMC13765342  PMID: 43031202

Abstract

The rise in atmospheric CO2 concentration makes effective carbon capture technologies increasingly important for mitigating climate change. Polypyrrole (PPy), a nitrogen-rich adsorbent material, has not been extensively studied regarding its high-pressure adsorption behavior, despite its unique advantages. In this study, we systematically investigated the adsorption and separation behaviors of PPy for CO2 under high-pressure conditions. High-pressure adsorption experiments demonstrated that the adsorption capacities of CO2, CH4, and N2 were 2.0, 0.65, and 0.41 mmol/g, respectively, at 25 °C and 15 bar. Calculations based on the IAST method indicate that PPy at high pressure exhibits adsorption selectivities of 16, 3.1, and 5.8 for CO2/N2 (15/85, v/v), CO2/CH4 (50/50, v/v), and CH4/N2 (50/50, v/v), respectively, demonstrating excellent separation performance, particularly for the CH4/N2 pair. In addition, the kinetics of adsorption were found to align with the Bangham model, suggesting that intra-particle diffusion governs the process, which is consistent with the hierarchical pore structure that facilitates rapid mass transfer. The high adsorption capacity, exceptional selectivity, and fast kinetics exhibited on the PPy adsorbent at elevated pressures underscore its potential application in industrial carbon capture fields such as flue gas treatment and natural-gas purification.

Keywords: polypyrrole, high-pressure adsorption, CO2/N2 selectivity, CH4/N2 separation

1. Introduction

The sustained increase in atmospheric carbon dioxide (CO2) concentration is widely recognized as a major contributor to global climate change and has intensified efforts to establish practical carbon capture and storage (CCS) technologies [1]. Among the available CO2 capture routes, adsorption-based processes have attracted considerable interest because they can potentially combine high capture efficiency, relatively low energy requirements, and convenient scale-up [2]. The effectiveness of such a process is strongly governed by the properties of the selected adsorbent. Polypyrrole (PPy) shows good environmental durability and resistance to oxidation and degradation, which favor its long-term use under demanding conditions [3]. The unique combination of electrical conductivity, flexibility, environmental stability, and biocompatibility makes PPy a versatile material with applications ranging from electronics and energy storage to biomedical and environmental technologies [4,5,6].

Ongoing research continues to expand the potential applications of PPy and its composites in diverse fields, showcasing its significance in the development of advanced materials and devices [7]. Kisiel et al. [8] synthesized PPy nanoparticle films using two straightforward template-free methods, demonstrating that the polymer films exhibit highly active and easily adaptable electrochemical properties, as determined by cyclic voltammetry, potentiometry, and the EIS method. Bansal et al. [9] conducted a study on the synthesis of self-supported PPy flexible electrodes with high resilience for the electrochemical reduction of nitrite. In the adsorption field, Wang et al. synthesized a PPy-intercalated bentonite material, denoted PPy-BT, through in situ chemical polymerization; this material efficiently removed Mo(VI) from water and retained a high regeneration capacity during consecutive adsorption–desorption cycles [10]. Comparative work on Cr(VI) uptake by PPy nanoparticles and nanotubes further showed that the nanotubular form provided stronger adsorption performance [11]. In the field of CO2 adsorption, existing studies on PPy and its composite adsorbents have mainly focused on ambient or low-pressure conditions [12]. Adhikari et al. [13] reported, for instance, that surfactant-free PPy achieved a CO2 adsorption capacity of 173.9 mL/g at 195 K. Recent studies have demonstrated that the adsorption capacity and selectivity of polypyrrole can be significantly enhanced through various modification strategies, such as doping with functional groups, composite formation with other materials, and nano-structuring [14]. These modifications can tailor the polymer’s surface chemistry and textural properties, thereby improving its interaction with CO2 molecules. However, the majority of these studies have been conducted at ambient or low pressures, leaving the potential for CO2 adsorption, especially under higher pressure conditions, relatively underexplored. Elevated-pressure operation is relevant to several industrial gas-separation scenarios, particularly natural-gas purification and other processes in which the CO2 partial pressure is appreciable. Understanding the CO2 adsorption and separation behavior of polypyrrole under these conditions is crucial for optimizing its performance in real scenarios [15].

In our previous study, the adsorption and separation of CO2, N2, and CH4 on pristine PPy were evaluated at atmospheric pressure, and the results identified PPy as a promising polymeric molecular sieve [16]. The linear adsorption isotherm implies a certain gas adsorption potential at elevated pressures, so the gas adsorption and separation properties of PPy at higher pressures are worth investigating. In this study, we performed the adsorption capacity tests of polypyrrole on CO2, N2, and CH4 gases under high pressure and explored the effect of pressure on its adsorption capacity and selectivity. In addition, we analyzed the CO2 adsorption kinetics of polypyrrole, which is a useful supplement to previous studies. “High pressure” here refers to pressures up to 15 bar, i.e., approximately one order of magnitude above ambient. This range is modest compared with pressures encountered in natural-gas pipelines (up to ~100 bar), but it is substantially higher than the ambient or sub-ambient pressures used in nearly all previous CO2 adsorption studies on PPy, and it covers the partial-pressure range relevant to flue-gas pretreatment and low-pressure natural-gas sweetening. The pseudo-first-order, pseudo-second-order, Bangham, and Elovich models are phenomenological rate expressions widely applied across pressure ranges [17]. Their transfer to high-pressure data assumes that the same elementary steps remain rate-relevant and that pressure dependence is absorbed into effective rate constants rather than altering the rate-law form [18]. This is an approximation, since elevated pressure can change both driving force and diffusivity; the models are therefore used here as comparative descriptors of uptake behavior rather than as mechanistic proof, and the fitted parameters are interpreted accordingly.

2. Materials and Methods

2.1. Adsorbent Preparation

Polypyrrole was prepared by the previously reported green oxidative polymerization route [16]. In brief, a pyrrole monomer was dispersed in aqueous medium and polymerized under controlled oxidative conditions at room temperature, without organic solvents or template agents. The resulting black precipitate was filtered, washed repeatedly with deionized water and ethanol until the filtrate was colorless, and dried under vacuum at 60 °C for 12 h. The dried powder was used directly without further purification.

2.2. High-Pressure Adsorption Measurements

CO2 (99.999%), CH4 (99.999%), and N2 (99.999%) were used as received. Prior to each measurement, the PPy sample (~0.5 g) was degassed under vacuum at 200 °C for 6 h to remove physisorbed water and air. Adsorption isotherms were measured on a gravimetric high-pressure sorption analyzer over 0–15 bar at 0, 25, and 50 °C. The temperature was controlled to ±0.1 K using a circulating bath. Each isotherm was measured in both adsorption and desorption modes to confirm reversibility. Adsorption kinetics were measured at 30, 40, and 50 °C by recording the sample mass as a function of time after stepwise introduction of CO2 at a fixed pressure.

2.3. Adsorption Isotherms and Calculation

Adsorption isotherms were simulated using the dual-site Langmuir (DSL) model [19], which is a well-established model for describing heterogeneous adsorption sites in porous adsorbents [20]:

q=q1b1p1+b1p+q2b2p1+b2p (1)
bi=bi0exp(∆HiRT) (2)

Here, q1 and q2 correspond to the maximum capacities of site 1 and site 2 (mmol/g); b is the temperature-dependent adsorption equilibrium constant; ∆H and T represent adsorption heat (kJ/mol) and adsorption temperature (K), respectively; and R denotes the ideal gas constant (8.314 J·mol−1·K−1).

The ideal adsorbed solution theory (IAST) was employed to predict the selectivities of CO2/N2, CO2/CH4, and CH4/N2 [21], while the Clausius–Clapeyron equation was used to determine the isosteric heats (Qst) for CO2 and CH4 [22].

3. Results and Discussion

3.1. Physicochemical Properties of PPy

Transmission electron microscopy images (Figure 1) show that the PPy synthesized in this study consists of uniformly sized spherical nanoparticles densely packed together, forming a characteristic 3D nano-aggregate structure with a primary particle diameter of approximately 50 nm. This dispersed but closely packed arrangement generates extensive external surface and numerous voids between adjacent particles [23]. The textural properties of PPy were quantified by the BET method and non-local density functional theory (NLDFT), which were used to determine the specific surface area and pore-size distribution, respectively. The measured BET surface area was 99 m2/g, while the total pore volume was 0.30 cm3/g, including 0.29 cm3/g assigned to mesopores. As presented in Figure 2a, the N2 adsorption–desorption curve exhibits a type-IV isotherm accompanied by an H3 hysteresis loop, indicating that mesopores constitute the principal pore class in PPy [24]. The pore size distribution curve further shows a concentrated pore distribution within the 2–10 nm range, along with some pore volume in a wider range (10–100 nm), suggesting that PPy is an adsorbent with a hierarchical pore structure. Additional surface-area and pore-distribution data for PPy synthesized by the same green route are provided in our published work [16]. The nitrogen-containing groups on the PPy molecular chains serve as the main active sites for CO2 adsorption, and the aforementioned nano-aggregate morphology and hierarchical porous structure ensure that these active sites are fully exposed on the pore surfaces [25]. The synergistic interaction between this macroscopic morphology, microscopic pore channels, and molecular sites not only provides sufficient diffusion pathways and available surfaces for gas molecules such as CO2, N2, and CH4 but also significantly enhances the CO2 adsorption capacity and capture kinetics [26], collectively constituting the key structural foundation for PPy as a high-performance adsorbent.

Figure 1.

Figure 1

TEM images of PPy under different magnifications.

Figure 2.

Figure 2

(a) N2 adsorption–desorption isotherms at 77 K (pressure axis in bar) with the pore size distribution shown in the inset; (b–d) high-pressure CO2, N2, and CH4 adsorption isotherms on PPy measured at 0, 25, and 50 °C; the relative standard deviation of the adsorption capacity was below 3% over the entire pressure range, and error bars in (b−d) represent one standard deviation.

3.2. Adsorption and Separation Studies

Figure 2b–d display the high-pressure adsorption isotherms of CO2, N2, and CH4 on PPy at 0, 25, and 50 °C over pressures extending to 15 bar. At the same temperature and equilibrium pressure, the adsorption capacity of PPy for these gases consistently ranks as CO2 > CH4 > N2. The adsorption capacities obtained for CO2, CH4, and N2 are 2.0, 0.65, and 0.41 mmol/g, respectively, at 25 °C and 15 bar. When the pressure is varied at 15 bar, the CO2 uptake is 2.56 mmol/g at 0 °C, 2.0 mmol/g at 25 °C, and 1.54 mmol/g at 50 °C. The outstanding CO2 capture performance of PPy can be explained by two main factors. On one hand, the relatively small kinetic diameter of CO2 (0.33 nm) favors its diffusion within the microporous channels of PPy [27]. Based on molecular properties and thermodynamic results, we tentatively attribute preferential CO2 adsorption to quadrupole-N-group interactions combined with pore-diffusion effects. Further spectroscopic characterization would provide more direct molecular-scale evidence for the adsorption mechanism. In contrast, although CH4 molecules have a higher polarizability, their lack of a quadrupole moment limits specific interactions with the functional groups on PPy surfaces [28]. N2 molecules do have a quadrupole moment, but their polarizability is lower, resulting in the weakest interaction with PPy surfaces and thus the lowest adsorption capacity [29].

A nearly linear increase in the adsorption isotherms of CO2, CH4, and N2 on PPy is observed over the tested pressure range, and no obvious saturation plateau is evident. This indicates that PPy still has the potential for further gas adsorption capacity under higher pressure. The adsorption amount of each gas increased progressively with system pressure. At elevated pressure, the larger gas-phase chemical potential promotes pore filling and enables molecules to occupy a broader range of adsorption regions. In addition to entering the microporous domains, gas molecules may adsorb on the internal surfaces of mesopores and larger voids and may form additional adsorption layers, thereby increasing the total capacity [30]. Temperature produced the opposite effect. For all three gases, adsorption decreased substantially as the temperature rose. Higher temperature enhances molecular thermal motion and increases the probability that adsorbed molecules escape from the adsorption layer into the gas phase [31]. Consequently, heating is unfavorable for stable retention of CO2, CH4, and N2 on PPy, consistent with an exothermic physical adsorption process.

Using the pure-component adsorption results described above, the ideal adsorbed solution theory (IAST) was applied to estimate the mixture selectivity of PPy for CO2/N2 (15/85, v/v), CO2/CH4 (50/50, v/v), and CH4/N2 (50/50, v/v) [32]. It should be noted that IAST-predicted selectivity is calculated from pure-component isotherm data. IAST assumes ideal adsorbed-solution behavior and ignores potential adsorbate–adsorbate interactions and competitive-adsorption deviations under real mixed-gas environments. Therefore, IAST results serve as the theoretical reference. Direct binary mixed-gas breakthrough experiments are required for rigorous validation of separation performance, which will be carried out in our future research work. The gas compositions were chosen to reflect the target industrial separation scenarios. CO2/N2 (15/85, v/v) corresponds to the approximate CO2 concentration in coal-fired power plant flue gas, which typically contains 10–15 vol% CO2 with the balance being mainly N2. CO2/CH4 (50/50, v/v) was adopted as a benchmark composition for natural-gas sweetening, where CO2 must be removed from methane-rich streams; equimolar compositions are widely used in IAST studies of CO2/CH4 separation to enable direct comparison across adsorbents. CH4/N2 (50/50, v/v) represents an equimolar benchmark relevant to methane enrichment from nitrogen-rich streams such as coalbed methane and biogas upgrading, where CH4/N2 selectivity is a key performance metric. Before performing the IAST calculations, the measured isotherms were correlated with the dual-site Langmuir model. The model reproduced the experimental data closely, and the fitted parameters are summarized in Table 1. The CO2/N2 selectivity at 15 bar was calculated to be 13.2, 16.0, and 16.9 at 0, 25, and 50 °C, respectively, using the parameters obtained from fitting the adsorption isotherms. In the CO2/N2 system (Figure 3a,d), although the selectivity at different temperatures shows a downward trend with increasing pressure, it remains above 13 throughout the entire pressure range, indicating that PPy maintained substantial CO2/N2 separation ability under elevated-pressure conditions. The decline in selectivity can be related to the tendency of the CO2 adsorption isotherm to become saturated at high pressures, while N2 adsorption increases almost linearly, resulting in a shifting balance in their competitive adsorption capabilities as pressure increases [33]. Notably, the stable separation performance exhibited by PPy at high pressures allows it to demonstrate significant advantages in accommodating pressure fluctuations encountered in practical high-pressure flue gas pretreatment systems, providing important support for the application of this material in industrial carbon capture devices [34].

Table 1.

Summary of DSL isotherm fitting results for CO2, CH4, and N2 adsorption on PPy.

Isotherms Parameters
q1
(mmol/g)
b10
(1/kPa)
ΔH1
(kJ/mol)
q2
(mmol/g)
b20
(1/kPa)
ΔH2
(kJ/mol)
R2
CO2 2.96 1.12 × 10−5 −20.3 0.89 4.66 × 10−9 −50.6 0.9967
CH4 0.40 1.79 × 10−5 −25.6 1.08 4.15 × 10−7 −27.3 0.9995
N2 1.07 3.99 × 10−6 −22.6 0.04 5.25 × 10−3 −12.8 0.9983

Figure 3.

Figure 3

(a–c) Fitting isotherms of CO2, N2, and CH4 adsorption amounts; (d) CO2/N2 (15/85, v/v) adsorption selectivities on PPy adsorbent at high pressure; (e) CO2/CH4 (50/50, v/v) selectivities on PPy adsorbent at high pressure; (f) CH4/N2 (50/50, v/v) adsorption selectivities on PPy adsorbent at high pressure.

Based on the DSL fitting parameters, the CO2/CH4 (50/50, v/v) selectivities at 15 bar were estimated as 2.8, 3.1, and 3.4 at 0, 25, and 50 °C, respectively (Figure 3b,e). The selectivity exhibited a consistent decrease with rising pressure across all three temperatures. Additionally, an increase in selectivity was observed with increasing temperature under higher pressure conditions. This phenomenon can be attributed to the more rapid decline in the adsorption capacity of the weakly adsorbed CH4 with increasing temperature compared to that of the strongly adsorbed CO2. In the CH4/N2 (50/50, v/v) system (Figure 3c,f), the selectivity change exhibits distinct temperature dependence: at 0 °C, the CH4/N2 system exhibits relatively high selectivity that gradually decreases with increasing pressure, while at 25 °C and 50 °C, the selectivity remains relatively stable, demonstrating excellent pressure insensitivity. The stable separation behavior of PPy across a broad pressure window is evident from this characteristic, and it likely originates from the homogeneous energetic landscape of the adsorption sites and the competitive equilibrium between CH4 and N2 within the pore network [35]. It is noteworthy that at a mixture pressure of 15 bar, the CH4/N2 selectivity values of 6.1, 5.8, and 4.2 were obtained at 0, 25, and 50 °C, respectively, demonstrating excellent separation performance for these two linear molecules on the PPy adsorbent. The persistence of this selectivity during pressure variation is relevant to methane enrichment processes, including biogas upgrading, natural-gas purification, and coalbed-methane separation. The gas separation performance positions PPy as a promising adsorbent for efficient biomethane production and pipeline natural-gas treatment, underscoring its substantial potential for practical engineering applications [36].

The isosteric heat of adsorption is an important energetic parameter for evaluating the interaction strength between an adsorbent and an adsorbate. Analysis of its loading dependence can also provide insight into the energetic origin of preferential adsorption [37]. The N2 isosteric heat is not shown because of the low N2 uptake and the near-linear isotherms, which precluded a reliable Clausius–Clapeyron analysis. As illustrated in Figure 4, the isosteric heat for CO2 decreased distinctly from approximately 40 to 17 kJ/mol as adsorption proceeded. This reduction indicates energetic heterogeneity on the PPy surface. At low loading, CO2 preferentially occupies the higher-energy regions, which may include characteristic small pores located near nitrogen-containing functional groups. With increasing loading, these favorable regions become progressively occupied and CO2 begins to populate more ordinary sites having lower adsorption energies [38]. In comparison, the adsorption heat for CH4 remains at a relatively low level and changes gently throughout, reflecting the weaker van der Waals interaction between CH4 and PPy. This significant difference in adsorption energy is primarily due to the diffusion advantage conferred by the smaller kinetic diameter of CO2 molecules as well as their strong quadrupole-specific interaction with nitrogen atoms in PPy [39]. CH4 interacts less strongly with the PPy surface and can therefore desorb more readily. This energetic contrast provides thermodynamic support for the preferential adsorption of CO2 and for the potential application of PPy in CO2/CH4 separation processes [40].

Figure 4.

Figure 4

CO2 and CH4 isosteric heat of PPy adsorbent.

The regenerability and cyclic stability of PPy were previously evaluated in our atmospheric-pressure study on the same material, in which PPy retained its adsorption capacity and structural integrity over repeated adsorption–desorption cycles [16]. In the present study, however, high-pressure cyclic adsorption–desorption tests were not performed. The custom-built breakthrough apparatus is limited by sealing integrity, pressure tolerance, and safety considerations, which currently preclude reliable long-term cycling at 15 bar. The stability of PPy under high-pressure cyclic operation therefore remains to be established and is identified as an important objective for future work.

3.3. Adsorption Kinetics

The kinetic measurements were performed at 30, 40, and 50 °C, whereas the equilibrium isotherms were measured at 0, 25, and 50 °C. The difference arises from the operating limits of the two instruments: the thermogravimetric kinetic system could not be operated below 30 °C. The two data sets overlap at 50 °C, where the equilibrium capacity obtained from the Bangham fit (0.3235 mmol/g) is consistent with the value derived from the isotherm, indicating that the two measurements are mutually consistent. Kinetic model fitting helps distinguish adsorption behavior and identify mechanisms controlling the process [41]. In this study, CO2 uptake on PPy was evaluated using the pseudo-first-order, pseudo-second-order, Bangham, and Elovich models.

(1) The pseudo-first-order kinetics assume a linear relationship between the adsorption rate and the driving force defined by the difference between the equilibrium capacity and the amount already adsorbed [42]. The governing equation takes the following form:

qt=qe1−e−k1t

In this equation, qt denotes the adsorbed amount at time t (mmol/g), qe is the equilibrium adsorption capacity (mmol/g), and k1 denotes the rate constant for the pseudo-first-order kinetics [42].

(2) According to the pseudo-second-order model, the rate of adsorption is related to the squared difference between the equilibrium adsorption amount and the amount adsorbed at any time [43]. Its mathematical form is:

qt=k2qe2t1+k2qet

The parameter k2 corresponds to the rate constant of the pseudo-second-order kinetic model.

We employed the Bangham kinetic model to characterize the pore diffusion mechanism of adsorbates in the porous structure. The model equation is [44]:

qt=qe−qee−k3tz

In this expression, k3 is the rate constant for adsorption and z is an empirical constant.

(3) The Elovich model describes adsorption kinetics where the rate declines exponentially as the adsorbed amount grows, and it is particularly suited for high-activation-energy processes [45]. The model is expressed as:

qt=a+k4lnt

Here, k4 is defined as the rate constant for the Elovich kinetics and a is a constant.

Comparison of the kinetic fits for CO2 adsorption on PPy showed that the Bangham model produced correlation coefficients (R2) above 0.98 at 30, 40, and 50 °C, as presented in Figure 5 and Table 2. At all three temperatures (30, 40, and 50 °C), the R2 values rank in the identical order of Bangham > pseudo-first-order > pseudo-second-order > Elovich. The Bangham model yields the highest R2 at each temperature (0.9875, 0.9933, and 0.9827, respectively) with the highest average value of 0.988, whereas the R2 values of the pseudo-second-order and Elovich models decline markedly with increasing temperature (from 0.9849 to 0.9451 and from 0.9689 to 0.9350, respectively). Moreover, the fitted parameters provide consistent physical support: (i) the Elovich parameter a, which should be positive as the initial adsorption rate, was negative at all temperatures, rendering this model physically meaningless despite R2 values above 0.93; (ii) the pseudo-second-order model systematically overestimated the equilibrium uptake qe compared with the pseudo-first-order and Bangham models; and (iii) the Bangham exponent z exceeded unity at all temperatures (1.10–1.42) and increased with temperature, which is the typical signature of intraparticle-diffusion-controlled adsorption and is consistent with the hierarchical meso-macroporous aggregate structure of PPy. The superior agreement of the Bangham equation indicates that a pore-diffusion-type description is consistent with the observed uptake behavior. However, this result should not be taken as definitive proof that intraparticle diffusion is the sole rate-controlling step [46]. The Bangham model is a phenomenological expression, and its good fit reflects the distributed nature of the adsorption sites and diffusion paths rather than a unique mechanism [47]. The open spaces between aggregated particles may serve as rapid transport channels, whereas the smaller pores provide adsorption regions with longer diffusion paths. Consequently, the measured kinetic response can reflect contributions from more than one pore scale while remaining well represented by the Bangham formulation. At 30 °C, the equilibrium capacity predicted by the Bangham model was closest to the measured value, with a difference below 0.05 mmol/g. The deviation became still smaller at the higher temperatures, indicating that the model adequately represents the measured adsorption response over the tested range. The consistent fits across the three temperatures also suggest that the principal rate behavior did not change markedly within the examined interval. These kinetic features complement previous high-pressure adsorption studies. The hierarchical pore structure of the material not only ensures adsorption capacity under high pressure, but its diffusion-controlled kinetic characteristics also guarantee separation efficiency in practical applications [48]. Especially in dynamic processes such as biogas upgrading and natural-gas purification, the rapid adsorption kinetics demonstrated by PPy provide important support for its industrial application.

Figure 5.

Figure 5

CO2 adsorption kinetics on PPy at 30–50 °C using (a) Pseudo-first-order, (b) Pseudo-second-order, (c) Bangham and (d) Elovich kinetic models.

Table 2.

Comparison of kinetic model fitting results and parameters for CO2 adsorption on PPy.

Kinetic Model Parameters 30 °C 40 °C 50 °C
Pseudo-first-order qe (mmol/g) 0.8799 0.6520 0.3419
k1 0.0416 0.0616 0.0678
R2 0.9866 0.9828 0.9651
Pseudo-second-order qe (mmol/g) 1.2443 0.8535 0.4401
k2 0.0264 0.0658 0.1452
R2 0.9849 0.9684 0.9451
Bangham qe (mmol/g) 0.8355 0.6173 0.3235
k3 0.0340 0.0309 0.0249
z 1.0979 1.2919 1.4196
R2 0.9875 0.9933 0.9827
Elovich a −0.2329 −0.1252 −0.0543
k4 0.2519 0.1928 0.0999
R2 0.9689 0.9633 0.9350

Table 3 compares the high-pressure CO2 adsorption performance of PPy with representative adsorbents reported in the literature. Under comparable conditions (25 °C, 15 bar), PPy exhibits a CO2 uptake of 2.0 mmol/g, which is lower than those of high-surface-area MOFs such as MOF-808 (6.1 mmol/g at 10 bar) and its N-doped analog MOF-808@N (5.6 mmol/g) but is essentially comparable to that of sludge-activated carbon (2.1 mmol/g at 15 bar, 30 °C) [49]. Considering that PPy is a pristine polymeric material rather than a high-surface-area carbonized or framework material, this capacity is notable. More importantly, PPy combines this moderate capacity with a distinctly higher CH4/N2 selectivity (5.8) and a favorable CO2/N2 selectivity (16.0), which are rarely reported simultaneously for zeolites and activated carbons under the same conditions. MOFs such as DUT-67@N and Zr-MOF achieve higher CO2 uptake (5.2 and 8.1 mmol/g, respectively), but their syntheses typically involve organic ligands, metal precursors, and multi-step activation, and their high-pressure CO2/CH4 selectivity (2.2–3.6 for Zr-MOF) does not exceed that of PPy [50,51]. These comparisons indicate that, although PPy does not outperform MOFs in absolute CO2 capacity, it offers a balanced combination of moderate uptake, good selectivity, simple and scalable green synthesis, and intrinsic structural stability. This trade-off between capacity and selectivity, together with the low-cost and environmentally benign preparation, supports the conclusion that PPy remains a practically relevant adsorbent for high-pressure CO2 separation duties such as natural-gas sweetening and coalbed-methane upgrading, where selectivity and process simplicity can be as important as absolute capacity.

Table 3.

High-pressure CO2 adsorption performance of PPy and representative adsorbents.

Adsorbent T (°C) P (bar) CO2 Uptake
(mmol/g)
Selectivity Ref.
PPy (this study) 25 15 2.0 CO2/N2 = 16.0; CO2/CH4 = 3.1; CH4/N2 = 5.8 This study
MOF-808 25 10 6.1 [50]
MOF-808@N 25 10 5.6 [50]
DUT-67@N 25 10 5.2 [50]
Zr-MOF 0 9.88 8.1 CO2/CH4 = 2.2–3.6 [51]
Sludge-activated
carbon
30 15 2.1 [49]

4. Conclusions

In this study, a polypyrrole adsorbent was successfully prepared through a green and feasible method, and its adsorption and separation performance for CO2 under high-pressure conditions was sequentially investigated. Material characterization results showed that PPy possesses a 3D agglomerated structure constructed of uniform nanoparticles, providing abundant specific surface area and effective diffusion pathways for gas adsorption. The high-pressure measurements showed that PPy preferentially adsorbed CO2, reaching 2.56 mmol/g at 273 K and 15 bar, while the capacities for CH4 and N2 were lower. The isotherms of all three gases continued to increase without a distinct saturation plateau in the investigated pressure region, indicating that further adsorption capacity remained available. Calculations based on the IAST for the PPy adsorbent at 15 bar and 25 °C predicted adsorption selectivities of 16, 3.1, and 5.8 for CO2/N2 (15/85, v/v), CO2/CH4 (50/50, v/v), and CH4/N2 (50/50, v/v), respectively, demonstrating excellent gas separation performance. Adsorption kinetic analysis confirmed that CO2 adsorption on PPy follows the Bangham model, indicating that the process is controlled by intra-particle diffusion mechanisms, which correlates well with the observed pore architecture. From a thermodynamic standpoint, the enhanced isosteric heat of CO2 adsorption on PPy relative to CH4 can be ascribed to the smaller kinetic diameter of CO2 and its strong quadrupole–nitrogen interactions within the PPy structure, offering a rational basis for the observed selectivity. Compared with representative MOFs, Zr-MOFs, and activated carbons under similar high-pressure conditions, PPy offers a moderate CO2 capacity but a superior CH4/N2 selectivity and a favorable CO2/N2 selectivity, together with a simple, green, and scalable synthesis. In conclusion, PPy exhibits a well-balanced combination of high-pressure adsorption capacity, separation selectivity, fast kinetics, and structural stability, establishing it as a promising adsorbent for CO2 capture and resource recovery.

Abbreviations

The following abbreviations are used in this manuscript:

CO2 carbon dioxide
CCS carbon capture and storage
PPy polypyrrole
DSL dual-site Langmuir
IAST ideal adsorbed solution theory
NLDFT non-local density functional theory

Author Contributions

Methodology, Z.W. (Zhe Wang); investigation, T.Z., Z.W. (Zhen Wang), J.H. and H.C.; writing—original draft, Z.W. (Zhe Wang) and Z.L.; writing—review and editing, Z.W. (Zhe Wang) and S.L.; supervision, S.L.; funding acquisition, Z.W. (Zhe Wang). All authors have read and agreed to the published version of the manuscript.

Data Availability Statement

The original contributions presented in this study are included in the article. Further inquiries can be directed to the corresponding author.

Conflicts of Interest

The authors declare no conflicts of interest.

Funding Statement

This research was funded by the GuangDong Basic and Applied Basic Research Foundation (no. 2024A1515110073), the Youth S&T Talent Support Programme of GDSTA (no. SKXRC2025405 and SKXRC2025406), the Youth Innovation Talent Project of Guangdong Provincial Ordinary University (no. 2025WQNCX026), the Scientific Research Start-up Funds of Guangdong Ocean University (no. 060302072614), and the Zhanjiang Unsubsidized Science and Technology Tackling Program Projects (no. 2024B01057). The APC was funded by the Youth S&T Talent Support Programme of GDSTA (no. SKXRC2025405) and the Scientific Research Start-up Funds of Guangdong Ocean University (no. 060302072614).

Footnotes

Disclaimer/Publisher’s Note: The statements, opinions and data contained in all publications are solely those of the individual author(s) and contributor(s) and not of MDPI and/or the editor(s). MDPI and/or the editor(s) disclaim responsibility for any injury to people or property resulting from any ideas, methods, instructions or products referred to in the content.

References

  • 1.Toan Vu T., Seo J., Kim E., Ryoo S.G., Park B.C., Song D. Techno-economic analysis of integrated MIDREX process with CO2 capture and storage: Evaluating sustainability and viability for iron production. Process Saf. Environ. Prot. 2024;189:1314–1322. doi: 10.1016/j.psep.2024.07.005. [DOI] [Google Scholar]
  • 2.Yue W., Yu Z., Zhang X., Liu H., Chen Z., Chen J., Wu H., Ma X. Preparation of multi-heteroatom self-doped carbon materials using industrial waste template agent combined with one-step carbonization: Multiple applications in supercapacitors and CO2 adsorption. Sep. Purif. Technol. 2025;373:133609. doi: 10.1016/j.seppur.2025.133609. [DOI] [Google Scholar]
  • 3.Shen Y., Chen N., Feng Z., Feng C., Deng Y. Treatment of nitrate containing wastewater by adsorption process using polypyrrole-modified plastic-carbon: Characteristic and mechanism. Chemosphere. 2022;297:134107. doi: 10.1016/j.chemosphere.2022.134107. [DOI] [PubMed] [Google Scholar]
  • 4.Yao T., Jia W., Tong X., Feng Y., Qi Y., Zhang X., Wu J. One-step preparation of nanobeads-based polypyrrole hydrogel by a reactive-template method and their applications in adsorption and catalysis. J. Colloid Interface Sci. 2018;527:214–221. doi: 10.1016/j.jcis.2018.05.052. [DOI] [PubMed] [Google Scholar]
  • 5.Xu D., Heng Y., Qin X., Hu D. Membrane-based symmetric supercapacitors composed of cellulose solution-derived polydopamine-modified separators and polypyrrole/graphene-doped polydopamine-modified electrodes. J. Energy Storage. 2022;50:104640. doi: 10.1016/j.est.2022.104640. [DOI] [Google Scholar]
  • 6.Wang F., Xu G., Shen W., Park S., Li Q. High-performance electro-responsive ionic soft actuators based on polypyrrole coated functional carboxylated bacterial cellulose nanofibers for bioinspired applications. Sens. Actuators A. 2023;363:114734. doi: 10.1016/j.sna.2023.114734. [DOI] [Google Scholar]
  • 7.Wang W., Lv Y., Liu H., Cao Z. Recent advances in application of polypyrrole nanomaterial in water pollution control. Sep. Purif. Technol. 2024;330:125265. doi: 10.1016/j.seppur.2023.125265. [DOI] [Google Scholar]
  • 8.Kisiel A., Korol D., Michalska A., Maksymiuk K. Polypyrrole nanoparticles of high electroactivity. Simple synthesis methods and studies on electrochemical properties. Electrochim. Acta. 2021;390:138787. doi: 10.1016/j.electacta.2021.138787. [DOI] [Google Scholar]
  • 9.Bansal R., Hald N., Martinez R., Chan C.K., Westerhoff P., Garcia-Segura S. Self-supported polypyrrole flexible electrodes for electrochemical reduction of nitrite. Chemosphere. 2023;338:139582. doi: 10.1016/j.chemosphere.2023.139582. [DOI] [PubMed] [Google Scholar]
  • 10.Wang L., Wang M., Muhammad H., Sun Y., Guo J., Laipan M. Polypyrrole-Bentonite composite as a highly efficient and low cost anionic adsorbent for removing hexavalent molybdenum from wastewater. J. Colloid Interface Sci. 2022;615:797–806. doi: 10.1016/j.jcis.2022.02.002. [DOI] [PubMed] [Google Scholar]
  • 11.Choe J., Ji J., Yu J., Jang K., Yun J., Choe S., Rim Y., Jo C. Adsorption of Cr(VI) in aqueous solution by polypyrrole nanotube and polypyrrole nanoparticle; Kinetics, isotherm equilibrium, and thermodynamics. Inorg. Chem. Commun. 2022;145:109981. doi: 10.1016/j.inoche.2022.109981. [DOI] [Google Scholar]
  • 12.Qiu L., Wang Y., Sui R., Zhu C., Weiwei Y., Yu Y., Li J. Preparation of a novel metal-free polypyrrole-red phosphorus adsorbent for efficient removal of Cr(VI) from aqueous solution. Environ. Res. 2023;224:115458. doi: 10.1016/j.envres.2023.115458. [DOI] [PubMed] [Google Scholar]
  • 13.Adhikari A., De S., Halder A., Pattanayak S., Dutta K., Mondal D., Rana D., Ghosh R., Bera N.K., Chattopadhyay S., et al. Biosurfactant tailored synthesis of porous polypyrrole nanostructures: A facile approach towards CO2 adsorption and dopamine sensing. Synth. Met. 2018;245:209–222. doi: 10.1016/j.synthmet.2018.09.005. [DOI] [Google Scholar]
  • 14.Wang Z., Goyal N., Liu L., Tsang D.C.W., Shang J., Liu W., Li G. N-doped porous carbon derived from polypyrrole for CO2 capture from humid flue gases. Chem. Eng. J. 2020;396:125376. doi: 10.1016/j.cej.2020.125376. [DOI] [Google Scholar]
  • 15.Negarestani M., Shayesteh H., Kheradmand A., Pahlevani F., Mollahosseini A., Javanshir S. Preparation of polypyrrole-functionalized recycled cotton fiber as a renewable and eco-friendly cellulose-based adsorbent for water decolorization: Comprehensive batch and fixed-bed column study. Surf. Interfaces. 2024;48:104360. doi: 10.1016/j.surfin.2024.104360. [DOI] [Google Scholar]
  • 16.Wang Z., Li Z., Liu L., Cao P., Li S., Li G.K. Green synthesis of polypyrrole for CO2 capture from humid flue gases. Green Chem. 2023;25:1513–1521. doi: 10.1039/d2gc04877a. [DOI] [Google Scholar]
  • 17.Rocky M.M.H., Rahman I., Yoshioka S., Keya J.A., Wong K.H., Mashio A.S., Hasegawa H. Modeling sorption kinetics in environmental separations: Advancing beyond traditional pseudo-order approaches. Sep. Purif. Technol. 2026;383:135987. doi: 10.1016/j.seppur.2025.135987. [DOI] [Google Scholar]
  • 18.Zhang Q., Wang J., Zhang L., Masoudi M., Hassanpouryouzband A., Song Y. Hydrogen adsorption kinetics and diffusion of clays: Implications for hydrogen geo-storage and natural hydrogen exploration. J. Colloid Interface Sci. 2025;700:138440. doi: 10.1016/j.jcis.2025.138440. [DOI] [PubMed] [Google Scholar]
  • 19.Mathias P.M., Kumar R., Moyer J.D., Schork J.M., Srinivasan S.R., Auvil S.R., Talu O. Correlation of multicomponent gas adsorption by the dual-site langmuir model. application to nitrogen/oxygen adsorption on 5A-Zeolite. Ind. Eng. Chem. Res. 1996;35:2477–2483. doi: 10.1021/IE950291Y. [DOI] [Google Scholar]
  • 20.Singh N., Dalakoti S., Sharma A., Chauhan R., Murali R.S., Divekar S., Dasgupta S., Aarti Shaping of MIL-53-Al and MIL-101 MOF for CO2/CH4, CO2/N2 and CH4/N2 separation. Sep. Purif. Technol. 2024;341:126820. doi: 10.1016/j.seppur.2024.126820. [DOI] [Google Scholar]
  • 21.Noorpoor A.R., Nazari Kudahi S. Analysis and study of CO2 adsorption on UiO-66/graphene oxide composite using equilibrium modeling and ideal adsorption solution theory (IAST) J. Environ. Chem. Eng. 2016;4:1081–1091. doi: 10.1016/j.jece.2016.01.017. [DOI] [Google Scholar]
  • 22.Santamaría L., Korili S.A., Gil A. Metal-Al layered double hydroxides synthesized from aluminum slags as efficient CO2 adsorbents at pre- and post-combustion temperature. J. Environ. Chem. Eng. 2023;11:110936. doi: 10.1016/j.jece.2023.110936. [DOI] [Google Scholar]
  • 23.Sun S., Yang F., Zhang X., Qian J., Wei K., An J., Sun Y., Wang S., Li X., Li Y. Highly dispersed carbon-encapsulated FeS/Fe3C nanoparticles distributed in Fe-N-C for enhanced oxygen electrocatalysis and Zn-air batteries. Chem. Eng. J. 2024;487:150673. doi: 10.1016/j.cej.2024.150673. [DOI] [Google Scholar]
  • 24.Song X., Zhou X., Lv X. Quantitative evaluation of pore connectivity of shales with a type H3 sorption hysteresis loop. J. Asian Earth Sci. 2023;247:105595. doi: 10.1016/j.jseaes.2023.105595. [DOI] [Google Scholar]
  • 25.Ma X., Xu W., Xue R., Su C., Su R., Li X., Zeng Z., Li L. Effect of mechanical compaction and nitrogen doping treatment on ultramicropore structure of biomass-based porous carbon and the mechanism of CO2 capture. Chem. Eng. Sci. 2025;303:120995. doi: 10.1016/j.ces.2024.120995. [DOI] [Google Scholar]
  • 26.Kamrava S., Tahmasebi P., Sahimi M. Linking morphology of porous media to their macroscopic permeability by deep learning. Transp. Porous Media. 2020;131:427–448. doi: 10.1007/s11242-019-01352-5. [DOI] [Google Scholar]
  • 27.Orabona F., Napolitano S., Badazhkova V.D., Perez-Sena W., Eränen K., Tesser R., Di Serio M., Russo V., Salmi T. CO2 cycloaddition to limonene diepoxide: Kinetic and mass transfer analysis. Chem. Eng. J. 2025;523:168292. doi: 10.1016/j.cej.2025.168292. [DOI] [Google Scholar]
  • 28.Ma C., Li N., Xue W., Guo X., Qiao Z., Zhong C. Polarization enhanced CH4/N2 separation in bromine functionalized ZIF-62 based mixed-matrix membranes. J. Membr. Sci. 2023;683:121829. doi: 10.1016/j.memsci.2023.121829. [DOI] [Google Scholar]
  • 29.Jia Y., Yi J., Wang X., Ge Z., Fu W., Lu Y., Xiao C. Cyclic CO2/N2 injection enhances CO2 storage and CH4 recovery in anthracite by optimizing pore structure and competitive adsorption. Gas Sci. Eng. 2026;145:205779. doi: 10.1016/j.jgsce.2025.205779. [DOI] [Google Scholar]
  • 30.Rahmani M., Mokhtarani B., Rahmanian N. High pressure adsorption of hydrogen sulfide and regeneration ability of ultra-stable Y zeolite for natural gas sweetening. Fuel. 2023;343:127937. doi: 10.1016/j.fuel.2023.127937. [DOI] [Google Scholar]
  • 31.Zhang Z., Chen Y., Chai K., Kang C., Peh S.B., Li H., Ren J., Shi X., Han X., Dejoie C., et al. Temperature-dependent rearrangement of gas molecules in ultramicroporous materials for tunable adsorption of CO2 and C2H2. Nat. Commun. 2023;14:3789. doi: 10.1038/s41467-023-39319-2. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 32.Dalakoti S., Singh N., Sharma A., Singh A., Sachdeva M., Divekar S., Arya A., Murali R.S., Dasgupta S. Cu-trimesate and mesoporous silica composite as adsorbent showing enhanced CO2/CH4 and CO2/N2 selectivity for biogas and flue gas separation. Microporous Mesoporous Mater. 2025;381:113354. doi: 10.1016/j.micromeso.2024.113354. [DOI] [Google Scholar]
  • 33.Tamtaji M., Kazemeini M., Kazemi A. High-throughput DFT screening of single-metal and high-entropy MOF-74 for selective CO2/N2 separation and H2 storage. Int. J. Hydrogen Energy. 2025;171:151276. doi: 10.1016/j.ijhydene.2025.151276. [DOI] [Google Scholar]
  • 34.Wang X., Liu Z., Yan J., Lv D., Chen X., Xu F., Zhou X., Li Z. High-pressure separation performance of Ni(TMBDC)(DABCO)0.5 featured low-polarity channel for CH4/N2 mixture. Sep. Purif. Technol. 2024;335:126019. doi: 10.1016/j.seppur.2023.126019. [DOI] [Google Scholar]
  • 35.Li Y., Wang Y., Guo M., Liu B., Zhou R., Lai Z. High-performance 7-channel monolith supported SSZ-13 membranes for high-pressure CO2/CH4 separations. J. Membr. Sci. 2021;629:119277. doi: 10.1016/j.memsci.2021.119277. [DOI] [Google Scholar]
  • 36.Etxeberria-Benavides M., Johnson T., Cao S., Zornoza B., Coronas J., Sanchez-Lainez J., Sabetghadam A., Liu X., Andres-Garcia E., Kapteijn F., et al. PBI mixed matrix hollow fiber membrane: Influence of ZIF-8 filler over H2/CO2 separation performance at high temperature and pressure. Sep. Purif. Technol. 2020;237:116347. doi: 10.1016/j.seppur.2019.116347. [DOI] [Google Scholar]
  • 37.Juul G., Korhonen A.-K., Neupane G., Lagus H., Kajaste J., Järvinen M., Vepsäläinen J. Development of a low-temperature heat engine using rapid thermal swing adsorption of CO2 onto activated carbon. Appl. Therm. Eng. 2025;275:126834. doi: 10.1016/j.applthermaleng.2025.126834. [DOI] [Google Scholar]
  • 38.Duan S., Xie Y., Yin H., Shen P. Investigation of CO2, CH4 and N2 adsorption mechanism on zeolite 4A using statistical physics and site energy distribution analysis. Microporous Mesoporous Mater. 2025;398:113826. doi: 10.1016/j.micromeso.2025.113826. [DOI] [Google Scholar]
  • 39.Ali Abd A., Jihad Kadhim Shabbani H., Helwani Z., Roslee Othman M. Novel design of pressure swing adsorption using compact plates for adsorption heat recuperation of CO2 capture in biomethane upgrading process. Energy Convers. Manag. 2022;268:115999. doi: 10.1016/j.enconman.2022.115999. [DOI] [Google Scholar]
  • 40.Pancione E., La Motta F., Boffa A., Lancia A., Erto A. Uncovering the potential of MSC CT-350 for CO2/CH4 separation toward the optimization of a pressure swing adsorption process for biogas upgrading. Fuel Process. Technol. 2024;256:108065. doi: 10.1016/j.fuproc.2024.108065. [DOI] [Google Scholar]
  • 41.Stefanelli E., Francalanci F., Vitolo S., Puccini M. Insights into adsorption mechanism and kinetic modeling of K2CO3-doped Li4SiO4 pellets for CO2 capture at high temperature and low concentration. Fuel. 2025;380:133161. doi: 10.1016/j.fuel.2024.133161. [DOI] [Google Scholar]
  • 42.Marinič D., Lavrič Ž., Huš M., Teržan J., Likozar B. Comparing thermodynamic equilibrium isotherms, mechanistic kinetic models and mass transfer resistances for fixed bed CO2 direct air capture (DAC) Chem. Eng. J. 2025;525:169895. doi: 10.1016/j.cej.2025.169895. [DOI] [Google Scholar]
  • 43.Maceiras R., Feijoo J., Alfonsin V., Alvarez-Feijoo M.A., Azofra L. Enhanced CO2 adsorption for hydrogen purification using calcined zeolite: Process analysis and kinetic study. Microporous Mesoporous Mater. 2026;399:113869. doi: 10.1016/j.micromeso.2025.113869. [DOI] [Google Scholar]
  • 44.Xie W., Wang H., Vandeginste V., Chen S., Gan H., Wang M., Yu Z. Thermodynamic and kinetic affinity of CO2 relative to CH4 and their pressure, temperature and pore structure sensitivity in the competitive adsorption system in shale gas reservoirs. Energy. 2023;277:127591. doi: 10.1016/j.energy.2023.127591. [DOI] [Google Scholar]
  • 45.Whaieb A.H., Jasim F.T., Abdulrahman A.A., Gheni S.A., Al-Bayati A.D.J., Fattah I.M.R., Türköz Karakullukçu N. A comprehensive study of CO2 capture using attapulgite and novel hybrid Attapulgite/13X zeolite composite: Kinetic, isotherm, and thermodynamic analysis. Microporous Mesoporous Mater. 2025;398:113770. doi: 10.1016/j.micromeso.2025.113770. [DOI] [Google Scholar]
  • 46.Martins V.F.D., Miguel C.V., Gonçalves J.C., Rodrigues A.E., Madeira L.M. Modeling of a cyclic sorption–desorption unit for continuous high temperature CO2 capture from flue gas. Chem. Eng. J. 2022;434:134704. doi: 10.1016/j.cej.2022.134704. [DOI] [Google Scholar]
  • 47.He W., Qiang H., Liang S., Guo F., Wang R., Cao J., Guo Z., Pang Q., Wei B., Sun J. Hierarchically porous wood aerogel/polypyrrole(PPy) composite thick electrode for supercapacitor. Chem. Eng. J. 2022;446:137331. doi: 10.1016/j.cej.2022.137331. [DOI] [Google Scholar]
  • 48.Mehmood S., Jianquan W., Jiang J., Lin C., Shang Y., Ran D. Harvesting low−grade heat by architecting the hierarchical porous structure of green delignified corn husk for solar−driven seawater desalination. J. Environ. Chem. Eng. 2025;13:119280. doi: 10.1016/j.jece.2025.119280. [DOI] [Google Scholar]
  • 49.Ma J., Liu Y., Chen S., Du Y., Wu H. Changes in the pore structure of modified sludge-activated carbon and its effect on the adsorption characteristics of CO2 under high pressure. Microporous Mesoporous Mater. 2022;345:112255. doi: 10.1016/j.micromeso.2022.112255. [DOI] [Google Scholar]
  • 50.Wamba H.N., Dalakoti S., Singh N., Divekar S., Ngoune J., Arya A., Dasgupta S. Facile aqueous medium synthesis of highly stable Zr-MOFs with promising CO2/CH4 adsorption selectivity for natural gas and biogas upgradation. Ind. Eng. Chem. Res. 2023;62:19773–19783. doi: 10.1021/acs.iecr.3c01862. [DOI] [Google Scholar]
  • 51.Abid H.R., Pham G.H., Ang H.-M., Tade M.O., Wang S. Adsorption of CH4 and CO2 on Zr-metal organic frameworks. J. Colloid Interface Sci. 2012;366:120–124. doi: 10.1016/j.jcis.2011.09.060. [DOI] [PubMed] [Google Scholar]

Associated Data

This section collects any data citations, data availability statements, or supplementary materials included in this article.

Data Availability Statement

The original contributions presented in this study are included in the article. Further inquiries can be directed to the corresponding author.


Articles from Materials are provided here courtesy of Multidisciplinary Digital Publishing Institute (MDPI)

RESOURCES