Skip to main content
Engineering Microbiology logoLink to Engineering Microbiology
. 2026 Oct 23;6(4):100310. doi: 10.1016/j.engmic.2026.100310

Engineered Yarrowia lipolytica for sustainable heavy metal bioremediation via enhanced alkaline phosphatase-driven biomineralization

Zhen Zheng a,#, Jianping Liu a,#, Xiaoman Xie a, Xinyi Hu a, Wanlin Zheng a, Shuhan Dai a, Qiyang Wang a, Yuan Liao b, Jinyong Yan a, Min Yang a, Yunjun Yan a,⁎, Li Xu a,⁎
PMCID: PMC13770613  PMID: 43036666

Highlights

  • •

    Engineered Yarrowia lipolytica alters the environmental fate of heavy metals.

  • •

    A stepwise bioprocess removed >99% of Cd2+ and Pb2+ from solution.

  • •

    Ultrahigh removal capacity reached 1251.64 mg Cd2+/g of biomass.

  • •

    Biomineralization converted metals into stable crystalline phosphate minerals.

  • •

    The data provide a biological pathway to reduce metal bioavailability and mobility.

Keywords: Alkaline phosphatase (PhoX), Bio-mineralization, Heavy metal bioavailability, Yarrowia lipolytica, Metal immobilization, Pollution remediation

Abstract

Heavy metal contamination poses persistent risks owing to metal mobility and bioavailability. In this study, we explored a biological strategy for altering the fate of metal ions by engineering the yeast Yarrowia lipolytica to secrete alkaline phosphatase (PhoX), thereby driving enzymatic metal-phosphate precipitation. Through copy number optimization and process refinement, a recombinant strain was obtained harboring three copies of phoX, exhibiting high extracellular PhoX activity (136.67 U/mL), and it showed a broad-spectrum precipitation of metal ions, including Cd2+, Mn2+, Co2+, Cr3+, Cu2+, Ni2+ and Pb2+. A two-step process was then designed, achieving near-quantitative removal efficiencies (>90%) for Cd2+, Mn2+, Co2+, Cr3+, and Pb2+ (ranging from 90.92% to 99.28%), while Cu2+ (89.09%) and Ni2+ (78.35%) showed slightly lower efficiencies. The system also achieved high removal capacities of up to 1251.64 mg Cd2+/g biomass. Microscopic and crystallographic analyses confirmed the formation of cell-associated, crystalline metal phosphate minerals, with Co2+ immobilized as Co3(PO4)2·8H2O. By utilizing a generally recognized as safe microorganism to convert soluble, bioavailable metals into stable mineral phases, we elucidated a biologically mediated immobilization pathway that can reduce metal toxicity and mobility, offering a sustainable mechanism for remediating metal-contaminated environments.

Graphical abstract

Image, graphical abstract

1. Introduction

The pervasive contamination of soil and aquatic ecosystems by heavy metals poses threats to environmental health owing to their toxicity, mobility, and bioavailability [[1], [2], [3], [4]]. Effective remediation requires strategies that not only remove metals but also alter their speciation to reduce ecological risks. Conventional physicochemical methods often entail high resource consumption and can generate secondary waste, highlighting the need for sustainable, biologically driven approaches that target the environmental fate of metal pollutants [[5], [6], [7], [8]]. Among biological strategies, microbially induced mineralization offers a pathway to convert soluble, bioavailable metal ions into stable solid phases, thereby reducing their mobility and toxicity [[9], [10], [11], [12], [13], [14], [15]]. Although microbially induced carbonate precipitation (MICP) has been widely studied, its reliance on urea hydrolysis produces ammonia, thus creating secondary pollution and limiting its environmental compatibility [[16], [17], [18], [19]]. In contrast, microbially induced phosphate precipitation (MIPP) represents a more environmentally congruent process that facilitates the formation of highly stable metal phosphate minerals with low solubility, enabling long-term sequestration with minimal risk of remobilization [[14], [20], [21], [22], [23]]. This enzymatic conversion of metal species addresses the core challenge in metal pollution of controlling bioavailability through speciation changes. The practical implementation of MIPP relies on robust, environmentally relevant microbial catalysts. The generally recognized as safe (GRAS) yeast Yarrowia lipolytica is a promising host because of its inherent stress tolerance, genetic tractability, and capacity for secretory protein production [24,25]. Its physiological resilience in metal-contaminated environments makes it suitable for developing biocatalytic platforms for altering the fates of metals in situ [[26], [27], [28], [29], [30]}.

A key enzyme enabling efficient phosphate release for MIPP is alkaline phosphatase (ALP, EC 3.1.3.1) that hydrolyzes organic phosphates to inorganic phosphate [22]. Although ALP activity has been explored in bioremediation contexts, its practical application for large-scale metal immobilization has been limited by low production yields, particularly in eukaryotic expression systems [31,32]. Engineering Y. lipolytica for high-level extracellular secretion of ALP represents a critical step in developing an efficient biological process for environmental remediation via metal-phosphate mineralization.

This study was designed to elucidate and enhance a biological pathway for metal immobilization by engineering Y. lipolytica for high-level secretion of the alkaline phosphatase, PhoX. We systematically optimized enzymatic production, evaluated the bio-mineralization efficiency and metal-removal capacity of engineered Y. lipolytica strains against a spectrum of heavy metal ions (Cd2+, Mn2+, Co2+, Cr3+, Cu2+, Ni2+, and Pb2+), and characterized the resulting mineral products. By focusing on the conversion of soluble metals into stable phosphate minerals, we generated data that provides mechanistic insights into a microbially facilitated immobilization process that reduces metal bioavailability, offering a sustainable biological strategy for mitigating heavy metal contamination in water and soil environments.

2. Methods and materials

2.1. Plasmids, strains, and recombinant strain construction

A codon-optimized phoX gene (GenBank: LC157911.1) was synthesized by Wuhan Tianyi Huayu Gene Technology Co., Ltd. (Sequence S1) and subcloned into the pUC57 vector to generate plasmid pUC57-phoX. This gene was subsequently amplified via PCR using pUC57-phoX as the template and primers F_pUC_57-phoX-7166 and R_pUC57-phoX-7166 as the primer pair. The plasmid pUAxp7166-rol was double-digested with Sfi I and Cla I, and the linearized fragment was gel-purified. The purified phoX PCR product was ligated into this digested vector using homologous recombination. The resulting construct was transformed into Escherichia coli Top10F ′ competent cells. Positive clones were screened by colony PCR using primers F_ phoX-2–7166 and R_phoX-2–7166, and plasmid DNA was extracted and verified by DNA sequencing. A confirmed single-copy expression plasmid was designated as pUAxp7166-phoX.

Multi-copy plasmids were constructed using the isocaudamer sites Spe I/Nhe I and Nsi I) flanking the expression cassette in pUAxp7166. Sequential digestion and ligation steps produced plasmids harboring tandem copies of the phoX cassette. Plasmids pUAxp7166–2phoX (two copies), Po1h-3phoX (three copies), Po1h-4phoX (four copies), Po1h-5phoX (five copies), and Po1h-6phoX (six copies) were verified by restriction digestion.

Plasmids were linearized with Nsi I and separately transformed into Y. lipolytica Po1h competent cells via the lithium acetate method. Transformants were selected on minimal dextrose liquid medium (13.4 g/L yeast nitrogen base (YNB), 0.4 mg/L biotin, and 20 g/L glucose). The Ura3 selection marker was subsequently excised via culturing on oleic acid-containing medium (13.4 g/L YNB, 0.4 mg/L biotin, 0.027 g/L uracil, 20 mL/L oleic acid) [33]. Genomic integration and copy numbers were confirmed by polymerase chain reaction (PCR). This process generated the engineered strains Po1h-1phoX, Po1h-2phoX, Po1h-3phoX, Po1h-4phoX, Po1h-5phoX, and Po1h-6phoX.

All engineered strains and the control Po1h strain were maintained on yeast extract peptone dextrose medium (YPD) agar plates (10 g/L yeast extract, 20 g/L peptone, and 20 g/L glucose, 20 g/L agar).

2.2. Fermentation and culture optimization

For pre-culture, a single colony was inoculated into YPD broth and incubated overnight. For the main fermentation, a two-stage process was used, involving subsequent expansion in BMSY medium (50 g/L d-sorbitol, 10 g/L yeast extract, 20 g/L tryptone, 100 mM potassium phosphate buffer pH 6.8, 13.4 g/L YNB and 0.4 mg/L biotin).

Optimization of culture conditions for the Po1h-3phoX strain was performed by systematically varying the carbon source type (sorbitol, sucrose, glucose, glycerol), carbon concentration (3–7% m/v), inoculation density (1–5% v/v), initial medium pH (5.5–7.5), and culture volume (30–70 mL in a 500 mL baffled flask).

2.3. Co-expression of helper proteins

To potentially enhance PhoX secretion, helper-protein genes (vgb, pdi, kar2, and hac1) were individually cloned into the integrative vector pUXpr7166. The resulting plasmids pUXpr7166-vgb, pUXpr7166-pdi, pUXpr7166-kar2, and pUXpr7166-hac1 were linearized with Nsi I and integrated into the genome of the Po1h-3phoX strain, generating the recombinant strains Po1h-3phoX-vgb, Po1h-3phoX-pdi, Po1h-3phoX-kar2, and Po1h-3phoX-hac1. Correct genomic integration was verified by PCR. Enzyme activities after a 5-day fermentation were compared with that of the parental strain. Relative enzyme activities were calculated, with the highest enzyme activity set to 100%.

2.4. Enzyme activity assay

PhoX activity in the culture supernatant was measured using a commercial PhoX Activity Assay Kit (Beijing Boxbio Science & Technology Co., Ltd., China) according to the manufacturer’s instructions. One unit (U) of enzyme activity was defined as the amount of enzyme that catalyzed the formation of 1 μmol of phenol per min at 37 °C and pH 10.0.

The extracellular protein concentrations in culture supernatants were determined by performing bicinchoninic acid protein assays with bovine serum albumin as the standard. Because the medium contained proteinaceous components, uninoculated medium was measured as the medium blank. For each sample, the measured protein concentration was first corrected by its dilution factor, and the medium blank was then subtracted. Extracellular protein concentrations were calculated as: protein assay value × dilution factor − medium blank. Protein-normalized PhoX activity was calculated by dividing extracellular PhoX activity (U/mL) by extracellular protein concentration (mg/mL) and expressed as U/mg extracellular protein. The optical density at 600 nm (OD600) of each fermentation culture was measured after appropriate dilution, and the biomass-normalized PhoX activity was calculated as the extracellular PhoX activity divided by the OD600 and expressed as U/OD600. These normalized values were calculated separately for each biological replicate before averaging.

2.5. Metal ion phosphate precipitation assay

2.5.1. Reaction setup

Fermentation broths of the control strain (Po1h) and the engineered strain (Po1h-3phoX) were centrifuged, and the cell pellets were resuspended in fresh buffer to an OD600 of 0.8–1.0. A standard 10 mL MIPP reaction system contained 8.9 mL of diluted broth, 1 mL of 0.5 M β-sodium glycerophosphate (as the phosphate donor substrate), and 100 μL of a 1 M stock solution of the target metal ion, yielding a final metal ion concentration of 10 mM. All reactions were conducted at 37 °C with rotation at 200 rpm.

Two distinct operational modes were employed to evaluate biomineralization efficiency. In the direct reaction method, the cell suspension, substrate, and metal ion solution were combined simultaneously and incubated for either 2 or 4 h. In contrast, the stepwise reaction method involved a 24 h pre-incubation of the cell suspension with the substrate to enable enzymatic generation of inorganic phosphate prior to metal exposure, after which the metal ion solution was added, and the reaction continued for an additional 4 h.

2.5.2. Biomineralization kinetic analysis

To evaluate the time-dependent behavior of the MIPP process, we selected Co2+ as a representative metal ion for biomineralization kinetic analysis. The reaction system was prepared as described in Section 2.5.1 using Po1h-3phoX as the engineered strain, β-glycerophosphate as the phosphate donor, and Co2+ at a final concentration of 10 mM. Reactions were conducted at 37 °C with shaking at 200 rpm. Samples were collected at 0, 15, 30, 60, 120, 240, and 360 min, followed by centrifugation at 5000 rpm and 4 °C for 7 min. The residual Co2+ concentration in the supernatant was determined by inductively coupled plasma-optical emission spectrometry (ICP-OES) after acid digestion, and the Co2+-removal efficiency at each time point was calculated as described in Section 2.5.3.

The kinetic data were fitted using a pseudo-second-order kinetic model, expressed as:

tqt=1k2qe2+tqe (1)

where qt and qe represent the amount of Co2+ removed at time t and at equilibrium (mg/g), respectively, and k2 is the pseudo-second-order rate constant (g·mg⁻¹·min⁻¹). The kinetic parameters were obtained from the slope and intercept of the linearized plot (t/qt​ versus t).

2.5.3. Metal analysis and removal calculation

Post-reaction, samples were centrifuged at 5000 rpm and 4 °C for 7 min. The supernatant was digested by boiling with 5 mL of 6 M HNO3 for 25 min, filtered through a 0.22 μm membrane, and diluted with HNO3 to a final acid concentration of 3%–5%. Metal ion concentrations were determined using an ICP-OES instrument (iCAP7200plus, Thermo Fisher Scientific). Standard curves (1–7.5 mM) were prepared for each metal.

The metal-removal efficiency (R, %) and metal-removal capacity (Q, mg/g) were calculated using Eqs. (2) and (3):

R=Ci−CfCi×100% (2)
Q=(Ci−Cf)×MwOD600×E×1000 (3)

where, Ci and Cf are the initial and final metal concentrations (μM), respectively; Mw is the atomic weight of heavy metal; OD600 is as defined above; and E is the average cell dry weight per OD600 unit in 1 L, determined experimentally as described below.

For dry cell weight (DCW) determinations, cell cultures with different OD600 values were harvested by centrifugation, washed twice with distilled water, dried to constant weight at 60 °C for 72 h, and weighed to establish an OD600–DCW calibration curve. The resulting conversion factor E (g DCW/L per OD600 unit) was used for biomass normalization in removal‑capacity calculations.

For routine DCW measurements, the cell pellet from 8.9 mL of diluted culture (OD600 = 0.8–1.0) was collected by centrifugation at 8000 rpm and 4 °C for 10 min, washed twice with distilled water, and dried to constant weight at 60 °C for 72 h.

2.6. Characterization of MIPP products

2.6.1. Electron microscopy

The morphological features of the mineralized precipitates were examined using complementary electron microscopy techniques. For scanning electron microscopy (SEM), freeze-dried MIPP samples were mounted on conductive adhesive, sputter-coated with gold for 180 s, and imaged using a GeminiSEM 300 microscope (Carl Zeiss). For transmission electron microscopy (TEM), pelleted materials were fixed in glutaraldehyde, deposited on copper grids, air-dried, and observed using an HT7700 microscope (Hitachi).

2.6.2. Crystallographic and spectroscopic analysis

Crystallographic phase composition and molecular functional groups were analyzed to characterize the mineral products. X-ray diffraction (XRD) analysis was performed using freeze-dried powders, with patterns collected from 10° to 90° (2θ). Phase identification was conducted using MDI Jade 6.0 software. Fourier transform infrared spectroscopy (FT-IR) was carried out by mixing approximately 1–2 mg of freeze-dried sample with KBr, pressing the mixture into transparent pellets, and analyzing the absorption spectra to identify characteristic functional groups involved in the mineralization process.

2.7. Statistical analysis

All experiments were performed with three independent biological replicates (n = 3). Data are presented as mean ± standard deviation (SD). Statistical analysis was conducted using one‑way analysis of variance followed by Tukey’s post‑hoc test. Significance levels are indicated in the figures as follows: NS (not significant, P > 0.05), * (significant, P < 0.05), and ⁎⁎ (highly significant, P < 0.01).

3. Results

3.1. Shake flask fermentation and heterologous expression of PhoX in Y. lipolytica

A recombinant Y. lipolytica strain was constructed harboring a single copy of the phoX gene. The strain was cultivated in a 500 mL baffled flask. After 120 h of fermentation, the whole-cell broth exhibited a PhoX activity of 7.52 U/mL (Fig. 1a). To test if the recombinant PhoX enzyme could still be a secreted enzyme, the culture was centrifuged, yielding the supernatant and the cell pellet. Examination of the PhoX activity in two fractions revealed that the enzymatic activity was primarily detected in the supernatant with negligible residual activity retained in the cell extracts. Thus, the heterologously expressed PhoX was also successfully secreted into the culture media, enabling the use of whole-cell broth for subsequent applications without the need for cell disruption.

Fig. 1.

Fig 1 dummy alt text

Enzyme activity and SDS-PAGE analysis of engineered strains. (a) Enzyme activity of a single-copy phoX engineered strain. (b) Enzyme activity of engineered strains with one to six copies of phoX. (c) SDS-PAGE analysis of extracellular proteins in culture supernatants. Lane M, protein marker; Lane 1, wild-type Y. lipolytica Po1h supernatant (control); Lane 2, empty-vector control supernatant; Lane 3, Po1h-3phoX culture supernatant. For (a) and (b), data are presented as the mean ± SD (n = 3). Asterisks indicate statistically significant differences among groups: *P < 0.05, **P < 0.01; NS, not significant (P > 0.05) (one-way ANOVA followed by Tukey’s post-hoc test).

To optimize the enzyme production, recombinant strains carrying one to six copies of the phoX gene were constructed and fermented. PhoX activity increased with the gene copy number up to three copies, reaching a maximum of 97.50 U/mL, which was 12.97-fold higher than that of the single-copy strain (Fig. 1b). Beyond three copies, activity significantly decreased, likely due to the metabolic burden associated with excessive heterologous gene expression. These results demonstrate a clear gene dosage effect, with an optimal gene copy number of three for maximizing PhoX yield in this host.

The expression and secretion of PhoX were further evaluated by sodium dodecyl sulfate–polyacrylamide gel electrophoresis (SDS-PAGE) analysis of extracellular protein fractions. Compared with the wild-type strain and empty-vector control, the engineered Po1h-3phoX strain showed an enhanced extracellular protein band near the predicted molecular weight of PhoX (Fig. 1c). In addition, a protein region near the predicted molecular weight of PhoX from the enriched extracellular fraction was excised from the SDS-PAGE gel and subjected to mass spectrometric analysis, confirming the presence of PhoX with 39.9% sequence coverage (Fig. S1). These results support the extracellular secretion of recombinant PhoX from Y. lipolytica.

To distinguish volumetric extracellular activity from biomass- and extracellular protein-related effects, the OD600 and extracellular protein concentration were measured for the optimized multi-copy strains, and normalized PhoX activities were calculated (Table S4). Po1h-3phoX showed the highest volumetric PhoX activity (124.12 ± 5.14 U/mL) and biomass-normalized activity (3.80 ± 0.53 U/OD600) among the tested strains with different copy numbers, although its OD600 (33.00 ± 3.77) was not higher than that of Po1h-1phoX (38.50 ± 2.29) or Po1h-4phoX (34.17 ± 3.88). In addition, Po1h-3phoX maintained a high extracellular protein-normalized activity of 53.30 ± 6.03 U/mg extracellular protein, comparable with that of Po1h-4phoX (56.72 ± 7.37 U/mg). Because Po1h-3phoX exhibited the highest volumetric and biomass-normalized activities, it was selected as the best-performing strain for subsequent MIPP experiments. These results indicated that the increased extracellular PhoX activity in Po1h-3phoX was not only attributable to biomass accumulation and the total extracellular protein concentration but also reflected a higher protein-normalized PhoX activity, compared with the low-copy strains (Po1h-1phoX and Po1h-2phoX).

3.2. Systematic optimization of culture conditions for enhanced PhoX production

To develop a scalable and efficient process, key fermentation parameters were optimized using the Po1h-3phoX strain. Among the carbon sources tested (sorbitol, sucrose, glucose, and glycerol), sorbitol was uniquely effective, supporting high PhoX activity, whereas others yielded negligible production (Fig. 2a). This specificity might have been linked to Y. lipolytica’s native metabolism and the impact of carbon catabolite repression on heterologous expression.

Fig. 2.

Fig 2 dummy alt text

Optimization of culture conditions for the engineered Po1h-3phoX strain. (a) Carbon source type. (b) Carbon source concentration. (c) Inoculum density. (d) Initial pH of medium. (e) Culture medium volume. (f) Incubation time. Data are presented as the mean ± SD (n = 3).

Subsequent optimization revealed the following ideal conditions: 6% (m/v) sorbitol concentration (Fig. 2b), a 2% inoculum density (Fig. 2c), an initial medium pH of 6.5 (Fig. 2d), and a culture volume of 40 mL in a 500 mL baffled flask (Fig. 2e). Applying this combined strategy increased the PhoX activity to 136.67 U/mL on day 5, representing a 1.40–fold enhancement over pre-optimized conditions (Fig. 2f). This optimization not only boosted the yield but also provided a foundation for a sustainable process scaling by defining resource-efficient parameters.

Given the role of auxiliary proteins in facilitating protein folding and secretion in yeast, we co-expressed genes encoding Vgb (vitreoscilla hemoglobin), Pdi (protein disulfide isomerase), Kar2 (ER chaperone), and Hac1 (UPR transcription factor). However, none of these co-expressed genes improved PhoX activity (Fig. S2). Strains expressing Pdi, Kar2, or Hac1 showed reduced yields.

3.3. Engineered Y. lipolytica for metal ion phosphate precipitation: performance and characterization

3.3.1. Establishing a biologically relevant MIPP assay

Initial MIPP assays performed using standard BMSY medium, which contains phosphate buffer, showed high Co2+ precipitation for both control and engineered strains (>72%), likely due to chemical precipitation (Fig. S3). When potassium phosphate was replaced with water, the mineralization rate for the engineered strain (Po1h-3phoX-H2O) remained high (80.95%), whereas that of the control strain (Po1h-H2O) decreased to 33.69%. These results confirm that the observed MIPP activity in the engineered strain was primarily enzymatically driven. All subsequent MIPP experiments were therefore conducted in phosphate-free medium to accurately assess biological mineralization.

3.3.2. Broad-spectrum metal biomineralization capability

The engineered strain was tested against a panel of toxic divalent and trivalent metal ions (Cd2+, Mn2+, Co2+, Cr3+, Cu2+, Ni2+, and Pb2+). Visual inspection after a 2 h reaction revealed abundant, colored precipitates in tubes containing the engineered strains, contrasting with the minimal precipitation observed with the control (except for Pb2+ and Cu2+) (Fig. 3).

Fig. 3.

Fig 3 dummy alt text

Visual assessment of MIPP reaction effects. (a) Cd2+, (b) Mn2+, (c) Co2+, (d) Cr3+, (e) Cu2+, (f) Ni2+, and (g) Pb2+. For each panel, sample 1: control strain Po1h; sample 2: engineered strain Po1h-3phoX.

Quantitative analysis using a direct reaction method (2 h) showed that the engineered strain achieved significantly higher removal efficiencies than did the control for most metals (Fig. 4a). A time-course study for Co2+indicated the reaction reached a plateau after 4 h (Fig. 4b). Kinetic fitting of these Co2+ time-course data further showed that the biomineralization process was better described by a pseudo-second-order model (Fig. S5), supporting a progressive precipitation-dominated process rather than instantaneous metal adsorption. Extending the reaction to 4 h improved performance for all metals. The engineered strain achieved removal efficiencies of 79.24% (Cd2+), 61.19% (Mn2+), 81.24% (Co2+), 44.02% (Cr3+), 84.57% (Cu2+), and 22.84% (Ni2+), whereas the control strain showed rates of 29.72%, 26.19%, 25.18%, 14.81%, 70.33%, and 3.87%, respectively (Fig. 4c). The high removal of Pb2+(> 98% by both strains) was attributed to the extremely low solubility product (Ksp) of lead phosphate owing to the abiotic precipitation [22,34].

Fig. 4.

Fig 4 dummy alt text

Metal-removal efficiency via the direct reaction method. (a) Removal efficiency for multiple metals after 2 h. (b) Time-course of Co2+ removal capacity. (c) Removal efficiency for multiple metals after 4 h. Data are presented as the mean ± SD (n = 3). In (a), asterisks indicate statistically significant differences among groups: *P < 0.05, **P < 0.01; NS, not significant (P > 0.05) (one-way ANOVA followed by Tukey’s post-hoc test).

To further enhance MIPP efficiency, we designed a stepwise (two-step) reaction method. The rationale was to enable the engineered Y. lipolytica to generate sufficient inorganic phosphate from β‑glycerophosphate before exposure to metal ions, thereby avoiding potential metal-induced inhibition of PhoX activity. With this strategy, the cell suspension and the phosphate substrate were pre-incubated for 24 h at 37 °C, followed by addition of metal ions (10 mM final concentration) and an additional 4 h reaction. As shown in Fig. 5, the two-step method dramatically improved metal removal compared with the direct 4 h reaction (Fig. 4c). For instance, Cd2+removal increased from 79.24% to 99.23%, and Cr3+ removal increased from 44.02% to 90.92% (Fig. 5a). The most pronounced enhancements were observed for metal ions that previously showed moderate removal (e.g., Cr3+, Ni2+, and Cu2+), indicating that the pre‑accumulation of phosphate effectively overcame the kinetic limitations of metal‑phosphate precipitation under direct mixing conditions. Correspondingly, the metal-removal capacities of the engineered strain reached 1251.64 mg Cd2+/g biomass, 607.71 mg Mn2+/g biomass, 618.38 mg Co2+/g biomass, 532.39 mg Cr3+/g biomass, 637.17 mg Cu2+/g biomass, and 517.87 mg Ni2+/g biomass (Fig. 5b). This two-step method presents a highly effective operational strategy for wastewater remediation.

Fig. 5.

Fig 5 dummy alt text

Metal-removal performance via the two-step reaction method (24 h + 4 h). (a) Metal-removal efficiency. (b) Metal-removal capacity. Data are presented as the mean ± SD (n = 3). Asterisks indicate statistically significant differences among groups: *P < 0.05, **P < 0.01; NS, not significant (P > 0.05) (one-way ANOVA followed by Tukey’s post-hoc test).

The metal-specific removal efficiencies can be rationalized by the solubility product constant (Ksp) values of the corresponding metal phosphates compiled from the literature [[35], [36], [37], [38], [39]]. As shown in Table S2, the Ksp values for Pb5(PO4)3OH, Pb3(PO4)2, Cd3(PO4)2, Co3(PO4)2, Ni3(PO4)2, and Cu3(PO4)2 were 1.70 × 10−81, 1.00 × 10−54, 2.53 × 10−33, 2.05 × 10−35, 4.74 × 10−32, and 1.40 × 10−37, respectively, with the specific references listed in Table S2. Notably, Pb2+, showed the lowest Ksp, achieved near-quantitative removal (>99%), whereas Ni2+, with a higher Ksp (4.74 × 10−32), showed lower removal efficiency (78.35%). For Cr3+, the Ksp of CrPO4 varied with the hydration state and crystallinity, with literature estimates generally ranging from 10−17 to 10−23 (see [36], for pKsp values of different hydrates). This range was consistent with the intermediate removal efficiency of Cr3+ (90.92%). Although a reliable Ksp value for Mn3 (PO4)2 was not available in the consulted sources, the high removal efficiency of Mn2+ (98.22%) suggests a similarly low solubility. These thermodynamic trends collectively account for the observed metal specific removal hierarchy (Pb2+ ≈ Cd2+ > Co2+ > Ni2+ > Cu2+ > Cr3+).

3.4. Morphological and structural analysis of minerals

Advanced microscopy and spectroscopy were employed to characterize the MIPP products. SEM analysis revealed distinct morphologies compared with the control. For Co2+, the control strain (Po1h) formed amorphous flakes, whereas the engineered strain (Po1h-3phoX) produced elongated crystals aggregated into large, porous spherical structures (Fig. 6a and 6b). The engineered strain formed metal-specific precipitates. Notably, Cd2+, Ni2+, and Pb2+ generated dense, amorphous coatings that encapsulated cells (Fig. 6c, 6g, and 6h). In contrast, Mn2+ yielded tightly packed, sheet‑like polymers (Fig. 6d), whereas Cr3+ and Cu2+produced regular spherical crystalline aggregates (Fig. 6e and 6f). Energy‑dispersive X‑ray spectroscopy (EDS) analysis confirmed the presence of phosphorus, oxygen, and the respective metals in these structures (Fig. S4), verifying their phosphate mineral composition.

Fig. 6.

Fig 6 dummy alt text

SEM images of MIPP products. (a, b) Co2+precipitates. (c) Cd2+precipitates. (d) Mn2+ precipitates. (e) Cr3+precipitates. (f) Cu2+precipitates. (g) Ni2+precipitates. (h) Pb2+ precipitates.

TEM analysis provided critical ultra-structural insights into the cell–mineral interface. For Co2+, the engineered strain exhibited a high density of flocculent, surface-associated mineral particles, starkly contrasting with the sparse adsorption observed on control cells (Fig. 7a and 7b). This clear disparity underscored the enzymatic activity’s role beyond native cellular adsorption. Observations of the engineered strain with other metals revealed distinct mineralization patterns consistent with SEM findings. Cd2+ biomineralization produced dark, granular aggregates enveloping the cell surface, with substantial intracellular dark aggregates also present, suggesting potential internal mineralization or transport (Fig. 7c). After Mn2+exposure, numerous transparent, flake‑like polymers surrounded the cells (Fig. 7d). Cr3+ treatment resulted in small, rounded particles adsorbed on the cell surface (Fig. 7e), whereas Cu2+ biomineralization generated extensive, outward-growing networks of dark flocculent material (Fig. 7f). Similarly, Ni2+ and Pb2+ mineralization showed dense adsorption of small particles and the formation of outward-extending flocculent polymers (Fig. 7g and 7h).

Fig. 7.

Fig 7 dummy alt text

TEM images of MIPP products. (a, b) Co2+precipitates. (c) Cd2+precipitates. (d) Mn2+precipitates. (e) Cr3+precipitates. (f) Cu2+precipitates. (g) Ni2+precipitates. (h) Pb2+precipitates.

The strong correlation between the SEM and TEM observations confirmed that the engineered Y. lipolytica facilitated the formation of abundant, metal-specific mineral structures—ranging from flakes to spherical particles—that closely associated with the cell surface. Notably, the frequent observation of intracellular dark aggregates across multiple metals, together with EDS data (Fig. S4) confirming the presence of P, O, and the corresponding metals, suggests the possibility of intracellular mineral formation or sequestration. However, we acknowledge that definitive confirmation of intracellular mineralization may require higher-resolution techniques (e.g., cryo-TEM or X-ray absorption spectroscopy) and this represents an interesting direction for future investigation.

3.4.1. Crystallographic and spectroscopic verification of the mineral phase

The mineral phase of the Co2+ precipitate was identified as cobalt phosphate octahydrate Co3(PO4)2·8H2O by XRD, matching the standard crystalline pattern (PDF #33–0432; Fig. 8a). This finding was confirmed by Fourier-transform infrared spectroscopy, which showed strong peaks for phosphate (PO43–) asymmetric stretching (1027–1079 cm–1), and bending (571–778 cm–1) (Fig. 8b) [40,41], along with bands for crystalline water [42,18]. The intensity of these phosphate peaks was markedly stronger for the engineered strain than for the control, corroborating the enzymatic generation of phosphate leading to stable mineral formation.

Fig. 8.

Fig 8 dummy alt text

XRD and FT-IR analysis of Co2+MIPP products. (a) XRD pattern. (b) FT-IR spectrum.

4. Discussion

We demonstrated a microbially mediated pathway for altering the environmental fate of heavy metals in this paper. The engineered Y. lipolytica strain served as a biocatalytic platform, secreting PhoX to hydrolyze organophosphates and induce precipitation of soluble metal ions via the formation of stable phosphate minerals. This transformation is environmentally critical, as it shifts metals from a bioavailable, mobile state to a geochemically stable, less toxic mineral phase [[43], [44], [45], [46]]. This process is underscored by high removal capacities and the crystallization of Co3 (PO4)2·8H2O, thus showing great potential to significantly reduce metal lability and ecological risk in contaminated systems.

The optimized two-step reaction method developed in this study not only achieved near‑quantitative removal and high capacity for multiple heavy metals but also offers several advantages over conventional remediation technologies. As summarized in Table S3, our PhoX‑based MIPP system exhibited superior performance when compared with conventional MIPP, MICP, chemical precipitation, and biosorption in terms of removal efficiency, capacity, by‑product generation, and long‑term mineral stability [[8], [47], [48], [49]]. Notably, conventional MIPP using Burkholderia sp. QY14 required 10 mM Ca2+ to achieve 99.97% Cd2+ removal, whereas our system achieved 99.23% Cd2+ removal without any Ca2+ addition [49]. Unlike MICP, which releases ammonia as a toxic by‑product, our MIPP process is completely free of hazardous by‑products. Furthermore, the formation of crystalline metal phosphate minerals ensures superior long‑term environmental stability versus the amorphous sludge generated by chemical precipitation or surface‑limited biosorption. These findings are consistent with earlier reports on biosorption and bio‑precipitation systems [[18], [50]], further underscoring the superior performance of our enzymatic MIPP approach. Kinetic analysis of Co2+ removal revealed that the biomineralization process followed a pseudo-second-order model (Fig. S5), indicative of a progressive precipitation driven mechanism rather than instantaneous adsorption. These data support the view that metal removal occurred primarily through enzymatically generated phosphate ions reacting with metal cations to form stable solid phases. Thus, this enzymatic MIPP strategy represents a significant advance in sustainable bioremediation technology. It should be noted that XRD analysis was performed only for the Co2+ precipitate (confirming Co3 (PO4)2·8H2O); however, EDS analysis confirmed the presence of P, O, and the metals of interest in all other precipitates (Fig. S4), supporting their phosphate mineral nature. Further work will include XRD characterization of Pb2+ and Cd2+ phosphate minerals.

In this study, co-expression of vgb, pdi, kar2, or hac1 did not improve PhoX production, and co-expression of pdi, kar2, or hac1 even reduced yields. This outcome may be explained by several factors. First, multi-gene overexpression imposes a significant metabolic burden on the host, diverting cellular resources away from recombinant protein synthesis [51,52]. Second, the native secretion machinery of Y. lipolytica may already operate near its capacity, so introducing additional chaperones or unfolded protein response (UPR) activators could cause secretion pathway saturation or disturb the endogenous folding equilibrium [53]. Third, co-expression of Hac1, which activates the UPR, may disrupt finely tuned UPR homeostasis and thereby reduce, rather than enhance, PhoX secretion. The lack of enhancement by Vgb suggests that oxygen supply was not limiting under our experimental conditions [[54], [55], [56]]. Collectively, these results indicate that the native secretory pathway of Y. lipolytica is sufficient for efficient PhoX production, simplifying strain engineering requirements.

Although the present findings provide proof‑of‑concept at the shake‑flask scale, further scale‑up studies are needed to assess practical applicability. Ongoing work in our laboratory is focused on bioreactor‑scale process development, including the optimization of oxygen transfer, agitation, and continuous operation modes. These efforts, together with techno‑economic analysis, will pave the way for potential industrial implementation of this PhoX-based MIPP system.

5. Conclusions

In this study, we engineered a recombinant Y. lipolytica strain for high-level secretion of PhoX, establishing an efficient biological pathway for metal immobilization. The strain demonstrated broad-spectrum precipitation of multiple heavy metals via enzymatic phosphate release, with a two-step process enabling near-quantitative removal and high sequestration capacities. Microscopic and crystallographic analyses confirmed the formation of cell-associated, crystalline metal phosphate minerals—exemplified by Co3(PO4)2·8H2O (XRD)—with EDS data further supporting the phosphate mineral nature of Cd2+, Mn2+, Cr3+, Cu2+, Ni2+, and Pb2+ precipitates. Kinetic analysis further indicated that a pseudo‑second‑order process occurred (Fig. S5), consistent with a precipitation‑dominated mechanism. By transforming soluble, toxic metal ions into stable mineral phases using a eukaryotic microbial host, this work highlights a novel microbial mechanism for altering metal speciation and reducing environmental bioavailability. The findings contribute to the development of biologically based remediation strategies that target the chemical fate of pollutants, offering a promising approach for mitigating metal mobility and toxicity in contaminated water and soil.

Data availability statement

The data that support the findings of this study are available from the corresponding author upon request.

CRediT authorship contribution statement

Zhen Zheng: Writing – original draft, Visualization, Validation, Investigation, Data curation. Jianping Liu: Writing – review & editing, Visualization, Validation, Formal analysis. Xiaoman Xie: Writing – review & editing, Validation, Formal analysis. Xinyi Hu: Validation, Formal analysis, Data curation. Wanlin Zheng: Writing – review & editing, Formal analysis. Shuhan Dai: Validation, Formal analysis. Qiyang Wang: Writing – review & editing, Visualization, Formal analysis, Data curation. Yuan Liao: Formal analysis, Data curation. Jinyong Yan: Writing – review & editing, Visualization, Methodology, Formal analysis. Min Yang: Writing – review & editing, Formal analysis. Yunjun Yan: Writing – review & editing, Resources, Methodology, Conceptualization. Li Xu: Writing – review & editing, Visualization, Supervision, Resources, Methodology, Funding acquisition, Formal analysis, Data curation, Conceptualization.

Declaration of competing interest

The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper.

Acknowledgements

This work was financially supported by the National Natural Science Foundation of China (NSFC) (31971206) and Hubei Provincial Natural Science Foundation and Geological Innovation Development Joint Fund (2026AFC0769). We also acknowledge the Analytical and Testing Center of HUST and the Chemical Experiment Center of HUST for their technical support.

Footnotes

Supplementary material associated with this article can be found, in the online version, at doi:10.1016/j.engmic.2026.100310.

Contributor Information

Yunjun Yan, Email: yanyunjun@hust.edu.cn.

Li Xu, Email: xuli@hust.edu.cn.

Appendix. Supplementary materials

mmc1.docx (761.9KB, docx)

References

  • 1.Acharya R., Sillanpää M., Al-Farraj S. A comprehensive review on sequestration of aqueous Cr (VI) over graphene based adsorbents. J. Hazard. Mater. Adv. 2025;18 doi: 10.1016/j.hazadv.2025.100670. [DOI] [Google Scholar]
  • 2.Ashraf S., Ali Q., Zahir Z.A., Ashraf S., Asghar H.N. Phytoremediation: environmentally sustainable way for reclamation of heavy metal polluted soils. Ecotoxicol. Environ. Saf. 2019;174:714–727. doi: 10.1016/j.ecoenv.2019.02.068. [DOI] [PubMed] [Google Scholar]
  • 3.Duhamel S. The microbial phosphorus cycle in aquatic ecosystems. Nat. Rev. Microbiol. 2025;23:239–255. doi: 10.1038/s41579-024-01119-w. [DOI] [PubMed] [Google Scholar]
  • 4.Li Q., Zhang M., Wei B., Lan W., Wang Q., Chen C., Gadd G.M. Fungal biomineralization of toxic metals accelerates organic pollutant removal. Curr. Biol. 2024;34:2077–2084.e3. doi: 10.1016/j.cub.2024.04.005. [DOI] [PubMed] [Google Scholar]
  • 5.Ates N., Uzal N. Removal of heavy metals from aluminum anodic oxidation wastewaters by membrane filtration. Environ. Sci. Pollut. Res. 2018;25:22259–22272. doi: 10.1007/s11356-018-2345-z. [DOI] [PubMed] [Google Scholar]
  • 6.Hwang S.K., Jho E.H. Heavy metal and sulfate removal from sulfate-rich synthetic mine drainages using sulfate reducing bacteria. Sci. Total. Environ. 2018;635:1308–1316. doi: 10.1016/j.scitotenv.2018.04.231. [DOI] [PubMed] [Google Scholar]
  • 7.Meng Y., Wang Q.Q., Zhang K.X., Yuan Q.K., Zhang J.D., Luan F.B. Cr(VI) adsorption on ferrihydrite at different natural aging stages: performance and mechanisms. J. Cleaner Prod. 2025;521 doi: 10.1016/j.jclepro.2025.146227. [DOI] [Google Scholar]
  • 8.Rajasekar A., Wilkinson S., Moy C.K.S. MICP as a potential sustainable technique to treat or entrap contaminants in the natural environment: a review. Environ. Sci. Ecotechnol. 2021;6 doi: 10.1016/j.ese.2021.100096. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 9.Chang J., Yang D., Lu C., Shu Z., Deng S., Tan L., Wen S., Huang K., Duan P. Application of microbially induced calcium carbonate precipitation (MICP) process in concrete self-healing and environmental restoration to facilitate carbon neutrality: a critical review. Environ. Sci. Pollut. Res. Int. 2024;31:38083–38098. doi: 10.1007/s11356-024-33824-7. [DOI] [PubMed] [Google Scholar]
  • 10.Qian X., Fang C., Huang M., Achal V. Characterization of fungal-mediated carbonate precipitation in the biomineralization of chromate and lead from an aqueous solution and soil. J. Cleaner Prod. 2017;164:198–208. doi: 10.1016/j.jclepro.2017.06.195. [DOI] [Google Scholar]
  • 11.Sun L., Zheng Y., Yu X. Flocculation-bio-treatment of heavy metals-vacuum preloading of the river sediments. Ecotox. Environ. Safe. 2020;201 doi: 10.1016/j.ecoenv.2020.110810. [DOI] [PubMed] [Google Scholar]
  • 12.Taharia M., Dey D., Das K., Sukul U., Chen J.S., Banerjee P., Dey G., Sharma R.K., Lin P.Y., Chen C.Y. Microbial induced carbonate precipitation for remediation of heavy metals, ions and radioactive elements: a comprehensive exploration of prospective applications in water and soil treatment. Ecotoxicol. Environ. Saf. 2024;271 doi: 10.1016/j.ecoenv.2024.115990. [DOI] [PubMed] [Google Scholar]
  • 13.Upadhyay S.K., Rani N., Kumar V., Mythili R., Jain D. A review on simultaneous heavy metal removal and organo-contaminants degradation by potential microbes: current findings and future outlook. Microbiol. Res. 2023;273 doi: 10.1016/j.micres.2023.127419. [DOI] [PubMed] [Google Scholar]
  • 14.Wang H.L., Yin Z.Y. Unconfined compressive strength of bio-cemented sand: state-of-the-art review and MEP-MC-based model development. J. Cleaner Prod. 2021;315 doi: 10.1016/j.jclepro.2021.128205. [DOI] [Google Scholar]
  • 15.Yu X., Jiang J., Liu J., Li W. Review on potential uses, cementing process, mechanism and syntheses of phosphate cementitious materials by the microbial mineralization method. Constr. Build. Mater. 2021;273 doi: 10.1016/j.conbuildmat.2020.121113. [DOI] [Google Scholar]
  • 16.Jiang L., Liu X., Yin H., Liang Y., Liu H., Miao B., Peng Q., Meng D., Wang S., Rajasekar A., Omoregie A.I., Kui K.F. Urease‑catalyzed microbial and enzymatic carbonate precipitation for eco‑friendly heavy metal remediation. Lett. Appl. Microbiol. 2025;78(2):ovaf022. doi: 10.1093/lambio/ovaf022. [DOI] [PubMed] [Google Scholar]
  • 17.Tang H., Xiang G., Xiao W., Yang Z., Zhao B. Microbial mediated remediation of heavy metals toxicity: mechanisms and future prospects. Front. Plant Sci. 2024;15 doi: 10.3389/fpls.2024.1420408. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 18.Zheng Z., Xie X., Hu X., Zheng W., Dai S., Liu J., Yan J., Yang M., Yan Y., Xu L. A novel bioengineered strategy for efficient heavy metals remediation: harnessing alkaline phosphatase-displaying E. coli to enhance microbial-induced phosphate precipitation. Bioresour. Technol. 2026;443 doi: 10.1016/j.biortech.2025.133849. [DOI] [PubMed] [Google Scholar]
  • 19.Zúñiga-Barra H., Toledo-Alarcón J., Torres-Aravena A., Jorquera L., Rivas M., Gutiérrez L., Jeison D. Improving the sustainable management of mining tailings through microbially induced calcite precipitation: a review. Miner. Eng. 2022;189 doi: 10.1016/j.mineng.2022.107855. [DOI] [Google Scholar]
  • 20.Chakraborty A., Banerjee P., Saha N.C., Pal P.K. Synergistic microbial consortia in the bioremediation of heavy metal-contaminated wastewater: mechanisms and sustainability perspectives. Environ. Geochem. Health. 2026;48:94. doi: 10.1007/s10653-026-02975-6. [DOI] [PubMed] [Google Scholar]
  • 21.Chaudhuri G., Venu-Babu P., Dalal D., Thilagaraj W.R. Application of alkaline phosphatase for heavy metals precipitation using ascorbic acid 2-phosphate as an effective natural substrate. Int. J. Environ. Sci. Technol. 2015;12:3877–3886. doi: 10.1007/s13762-014-0749-y. [DOI] [Google Scholar]
  • 22.Simopoulos T.T., Jencks W.P. Alkaline phosphatase is an almost perfect enzyme. Biochemistry. 1994;33:10375–10380. doi: 10.1021/bi00200a018. [DOI] [PubMed] [Google Scholar]
  • 23.Tang F., Yue J., Tian J., Ge F., Li F., Liu Y., Deng S., Zhang D. Microbial induced phosphate precipitation accelerate lead mineralization to alleviate nucleotide metabolism inhibition and alter penicillium oxalicum's adaptive cellular machinery. J. Hazard. Mater. 2022;439 doi: 10.1016/j.jhazmat.2022.129675. [DOI] [PubMed] [Google Scholar]
  • 24.Madzak C. Engineering Yarrowia lipolytica for use in biotechnological applications: a review of major achievements and recent innovations. Mol. Biotechnol. 2018;60:621–635. doi: 10.1007/s12033-018-0093-4. [DOI] [PubMed] [Google Scholar]
  • 25.J.M. Nicaud, 2012. Yarrowia lipolytica. 29, 409–418. 10.1002/yea.2921 [DOI] [PubMed]
  • 26.Bankar A., Zinjarde S., Telmore A., Walke A., Ravikumar A. Morphological response of Yarrowia lipolytica under stress of heavy metals. Can. J. Microbiol. 2018;64:559–566. doi: 10.1139/cjm-2018-0050. [DOI] [PubMed] [Google Scholar]
  • 27.Bankar A., Zinjarde S., Shinde M., Gopalghare G., Ravikumar A. Heavy metal tolerance in marine strains of Yarrowia lipolytica. Extremophiles. 2018;22:617–628. doi: 10.1007/s00792-018-1022-y. [DOI] [PubMed] [Google Scholar]
  • 28.Bankar A.V., Kumar A.R., Zinjarde S.S. Environmental and industrial applications of Yarrowia lipolytica. Appl. Microbiol. Biotechnol. 2009;84:847–865. doi: 10.1007/s00253-009-2156-8. [DOI] [PubMed] [Google Scholar]
  • 29.Oyetibo G.O., Miyauchi K., Suzuki H., Endo G. Mercury removal during growth of mercury tolerant and self-aggregating Yarrowia spp. AMB Express. 2016;6:99. doi: 10.1186/s13568-016-0271-3. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 30.Strouhal M., Kizek R., Vacek J., Trnková L., Němec M. Electrochemical study of heavy metals and metallothionein in yeast Yarrowia lipolytica. Bioelectrochemistry. 2003;60:29–36. doi: 10.1016/S1567-5394(03)00043-4. [DOI] [PubMed] [Google Scholar]
  • 31.Tian J., Ge F., Zhang D., Deng S., Liu X. Roles of phosphate solubilizing microorganisms from managing soil phosphorus deficiency to mediating biogeochemical P cycle. Biology. 2021;10:158. doi: 10.3390/biology10020158. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 32.Zeng Q., Tang L., Zhang Y., Shao Y., Wu W., Wang J., Ding X., Han X., Muhammad B. Isolation and characterization of phosphate-solubilizing bacteria from rhizosphere of poplar on road verge and their antagonistic potential against various phytopathogens. BMC. Microbiol. 2023;23:221. doi: 10.1186/s12866-023-02953-3. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 33.Zhou Q., Jiao L., Li W., Hu Z., Li Y., Zhang H., Yang M., Xu L., Yan Y. A novel cre/lox-based genetic tool for repeated, targeted and markerless gene integration in Yarrowia lipolytica. Int. J. Mol. Sci. 2021;22 doi: 10.3390/ijms221910739. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 34.Singh A., Kumar S. Development of a robust microbial biosorbent for remediation of Pb2+ from lab-simulated water: characterization, optimization, modelling and a multi-metal analysis. J. Environ. Chem. Eng. 2025;13 doi: 10.1016/j.jece.2025.119431. [DOI] [Google Scholar]
  • 35.Ball D.W., Key J.A. Introductory chemistry-1st Canadian edition. 2014. https://opentextbc.ca/introductorychemistry/back-matter/appendix-solubility-constants-for-compounds-at-25c/ Victoria, B.C.: BCcampus, Appendix C: Solubility Constants for Compounds at 25 °C.
  • 36.ChemicalBook Chromium (III) phosphate tetrahydrate. 2026. https://www.chemicalbook.com/ProductChemicalPropertiesCB1176599.htm CAS 10101-59-4.
  • 37.Lide D.R., editor. CRC Handbook of Chemistry and Physics. 84th ed. CRC Press; Boca Raton, FL, USA: 2004. [Google Scholar]
  • 38.Speight J.G., editor. Lange's Handbook of Chemistry. 16th ed. McGraw-Hill; New York, NY, USA: 2005. [Google Scholar]
  • 39.Zhu Y., Zhu Z., Zhao X., Liang Y., Huang Y. Characterization, dissolution, and solubility of lead hydroxypyromorphite [Pb5(PO4)3OH] at 25–45 °C. J. Chem. 2015;2015 doi: 10.1155/2015/269387. [DOI] [Google Scholar]
  • 40.Frost R.L., Martens W., Williams P.A., Kloprogge J.T. Raman spectroscopic study of the vivianite arsenate minerals. J. Raman. Spectrosc. 2003;34:751–759. doi: 10.1002/jrs.1049. [DOI] [Google Scholar]
  • 41.Walpersdorf E., Bender Koch C., Heiberg L., O'Connell D.W., Kjaergaard C., Bruun Hansen H.C. Does vivianite control phosphate solubility in anoxic meadow soils? Geoderma. 2013;193-194:189–199. doi: 10.1016/j.geoderma.2012.10.003. [DOI] [Google Scholar]
  • 42.Rajkumar M., Sundaram N.M., Rajendran V. Preparation of size controlled, stoichiometric and bioresorbable hydroxyapatite nanorod by varying initial pH, Ca/P ratio and sintering temperature. Dig. J. Nanomater. Bios. 2011;6:169–179. [Google Scholar]
  • 43.Bolan N., Kunhikrishnan A., Thangarajan R., Kumpiene J., Park J., Makino T., Kirkham M.B., Scheckel K. Remediation of heavy metal(loid)s contaminated soils – To mobilize or to immobilize? J. Hazard. Mater. 2014;266:141–166. doi: 10.1016/j.jhazmat.2013.12.018. [DOI] [PubMed] [Google Scholar]
  • 44.Chen T., Wen X.C., Zhou J.W., Lu Z., Li X.Y., Yan B. A critical review on the migration and transformation processes of heavy metal contamination in lead-zinc tailings of China. Environ. Pollut. 2023;338 doi: 10.1016/j.envpol.2023.122667. [DOI] [PubMed] [Google Scholar]
  • 45.Johnson V.E., Jallawide B.W., Anaman R., Tarpeh T.T., Jarnda K.V., Sunday B., Wingbah M.W., Abeeku Tarley J.P., Zhang K.J., Shi Y. Microbial driven iron mineral transformation and its role in pollutant migration and transformation: a critical review. J. Environ. Chem. Eng. 2025;13 doi: 10.1016/j.jece.2025.119611. [DOI] [Google Scholar]
  • 46.Miretzky P., Fernández-Cirelli A. Phosphates for Pb immobilization in soils: a review. Environ. Chem. Lett. 2008;6:121–133. doi: 10.1007/s10311-007-0133-y. [DOI] [Google Scholar]
  • 47.Huang H., Jia Q., Jing W., Dahms H.U., Wang L. Screening strains for microbial biosorption technology of cadmium. Chemosphere. 2020;251 doi: 10.1016/j.chemosphere.2020.126428. [DOI] [PubMed] [Google Scholar]
  • 48.Razzak S.A., Faruque M.O., Alsheikh Z., Alsheikhmohamad L., Alkuroud D., Alfayez A., Zakir Hossain S.M., Hossain M.M. A comprehensive review on conventional and biological-driven heavy metals removal from industrial wastewater. Environ. Adv. 2022;7 doi: 10.1016/j.envadv.2022.100168. [DOI] [Google Scholar]
  • 49.Zeng G., Qiao S., Wang X., Sheng M., Wei M., Chen Q., Xu H., Xu F. Immobilization of cadmium by Burkholderia sp. QY14 through modified microbially induced phosphate precipitation. J. Hazard. Mater. 2021;412 doi: 10.1016/j.jhazmat.2021.125156. [DOI] [PubMed] [Google Scholar]
  • 50.Chaudhuri G., Shah G.A., Dey P.S.G., Venu-Babu P., Thilagaraj W.R. Enzymatically mediated bioprecipitation of heavy metals from industrial wastes and single ion solutions by mammalian alkaline phosphatase. J. Environ. Sci. Heal. A Tox. Hazard. Subst. Environ. Eng. 2013;48:79–85. doi: 10.1080/10934529.2012.707851. [DOI] [PubMed] [Google Scholar]
  • 51.Oh M.H., Cheon S.A., Kang H.A., Kim J.-Y. Functional characterization of the unconventional splicing of Yarrowia lipolytica HAC1 mRNA induced by unfolded protein response. Yeast. 2010;27:443–452. doi: 10.1002/yea.1762. [DOI] [PubMed] [Google Scholar]
  • 52.Tartik M. Yeast stress response to synthetic constructs. ACS. Synth. Biol. 2026;15(2):368–386. doi: 10.1021/acssynbio.5c00715. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 53.Butz J.A., Niebauer R.T., Robinson A.S. Co-expression of molecular chaperones does not improve the heterologous expression of mammalian G-protein coupled receptor expression in yeast. Biotechnol. Bioeng. 2003;84:292–304. doi: 10.1002/bit.10771. [DOI] [PubMed] [Google Scholar]
  • 54.Bhave S.L., Chattoo B.B. Expression of vitreoscilla hemoglobin improves growth and levels of extracellular enzyme in Yarrowia lipolytica. Biotechnol. Bioeng. 2003;84:658–666. doi: 10.1002/bit.10817. [DOI] [PubMed] [Google Scholar]
  • 55.Kallio P.T., Jin Kim D., Tsai P.S., Bailey J.E. Intracellular expression of Vitreoscilla hemoglobin alters Escherichia coli energy metabolism under oxygen-limited conditions. Eur. J. Biochem. 1994;219:201–208. doi: 10.1111/j.1432-1033.1994.tb19931.x. [DOI] [PubMed] [Google Scholar]
  • 56.Mirończuk A.M., Kosiorowska K.E., Biegalska A., Rakicka-Pustułka M., Szczepańczyk M., Dobrowolski A. Heterologous overexpression of bacterial hemoglobin VHb improves erythritol biosynthesis by yeast Yarrowia lipolytica. Microb. Cell Fact. 2019;18:176. doi: 10.1186/s12934-019-1231-9. [DOI] [PMC free article] [PubMed] [Google Scholar]

Associated Data

This section collects any data citations, data availability statements, or supplementary materials included in this article.

Supplementary Materials

mmc1.docx (761.9KB, docx)

Data Availability Statement

The data that support the findings of this study are available from the corresponding author upon request.


Articles from Engineering Microbiology are provided here courtesy of Shandong University

RESOURCES