Skip to main content
The Scientific World Journal logoLink to The Scientific World Journal
. 2026 Nov 17;2026:2771399. doi: 10.1155/tswj/2771399

Systematic Review and Meta‐Analysis of Recycled Brick Powder as a Partial Replacement for Portland Cement (2014–2025)

Bahiru Bewket Mitikie 1,✉, Walied A Elsaigh 1, Dunisani Thomas Chabalala 1
Editor: Deepali Deepali
PMCID: PMC13775083  PMID: 43042452

Abstract

This study systematically reviews and conducts a meta‐analysis to evaluate the potential of recycled clay brick powder (RCBP) as a sustainable alternative to Portland cement in concrete production. A comprehensive literature search was performed using the Web of Science database, following the PRISMA 2020 flowchart. The search focused on studies exploring the use of RCBP as a partial replacement for Portland cement in concrete. The global research distribution, analyzed using VOS viewer, indicates that most studies originate from China, India, the United States, and England. A meta‐analysis was conducted using Jeffreys′ Amazing Statistics Program (JASP) to compare the effect sizes of concrete mixes incorporating RCBP against control mixes. Even if the findings reveal a slight reduction in compressive strength as the proportion of clay brick powder increases, the extant review shows that the influence of RCBP is governed by a set of interdependent parameters, including the replacement ratio, curing duration and conditions, particle fineness, as well as the chemical and mineralogical characteristics of the brick powder. A forest plot analysis further highlights the extent of strength reduction and its variation across different studies. Although RCBP presents a viable and sustainable alternative to cement, optimizing the replacement ratio and integrating complementary materials could enhance performance. Future research should focus on innovative techniques to improve the durability and mechanical properties of RCBP concrete, ensuring its feasibility without compromising structural integrity.

Keywords: brick powder, cement replacement, meta-analysis, systematic review

1. Introduction

Portland cement concrete (PCC) is a widely used construction material. It is the most important cement‐based material. The cement industry releases significant carbon dioxide and consumes significant amounts of energy, highlighting the need for improved cement technology to reduce these negative effects [1]. The growth of the building industry has significantly increased the generation of construction waste, which accounts for 40% of the total solid waste. The construction industry is known to be accountable for the depletion of several nonrenewable resources as well as leaving a considerable volume of industrial waste materials [2].

Waste clay bricks are found in large quantities and are produced as a result of faulty production or due to construction and demolition activities, which requires proper disposal from an environmental perspective [3]. Clay bricks are one of the largest construction wastes by output and they have been reutilized in concrete as aggregate replacement after crushing or as cement replacement after grinding [4]. Eco‐cement made using RCBP is a sustainable building material that incorporates recycled brick waste into the cement production process. The use of recycled clay bricks powder (RCBP) in concrete is found to be sustainable and promising [5, 6]. The RCBP was found to have pozzolanic activity besides the good filler effect when mixed with Portland cement. It is not surprising that the last few years have witnessed an increase in research relating to the use of RCBP in concrete. A carefully measured quantity of RCBP was mixed with dry cement and was used to produce high‐performance concrete mixtures [7]. The green concrete mixtures were developed using various percentage proportions of RCBP to partially replace the Portland cement at percentage proportions of 0%, 10%, 20%, 30%, and 40% [8]. Besides the engineering benefits, the use of RCBP in Portland cement production has several advantages, including cost‐effectiveness, resource conservation, energy efficiency, and environmental benefits [9, 10].

The pozzolanic reactivity of RCBP is primarily controlled by its mineralogical composition, with particular emphasis on the relative contents of amorphous silica (SiO2) and alumina (Al2O3). These amorphous phases react with calcium hydroxide liberated during cement hydration to form secondary calcium silicate hydrate and calcium aluminate hydrate phases, which significantly enhance the long‐term strength and durability of cementitious systems. By contrast, crystalline quartz exhibits negligible pozzolanic activity and acts predominantly as an inert filler, especially at early curing ages. This distinction has now been explicitly incorporated into the manuscript to rationalize the variability in mechanical performance reported across different studies [11].

The revised manuscript now discusses particle fineness and grinding characteristics as key factors affecting RCBP performance. Finer brick powders, with higher specific surface area, accelerate dissolution of reactive silica and alumina, increase nucleation sites for cement hydration, improve particle packing, and promote additional hydration products. Coarser particles mainly act as inert fillers with limited pozzolanic activity. These fineness‐related differences partly explain the variation in optimum replacement levels and compressive strength reported in the primary studies [12]. The physical filler effect from the true pozzolanic effect of RCBP gains mainly due to improved particle packing, filler action, and nucleation, whereas long‐term strength development arises from the gradual pozzolanic reaction between amorphous aluminosilicates and calcium hydroxide, forming additional C–S–H gel and refining the pore structure. This mechanistic explanation clarifies the performance trends observed in the meta‐analysis [13, 14].

The primary purpose of a systematic review is to comprehensively gather and synthesize all available evidence on a specific research question, following a structured methodology. It begins with a clearly defined research question, followed by using explicit inclusion and exclusion criteria to select relevant studies. This ensures that the review captures the most relevant and high‐quality research available. A meta‐analysis serves the purpose of quantitatively synthesizing results from multiple studies to derive a more precise estimate of the effect or relationship being examined. Meta‐analysis enhances statistical power and improves the reliability of the results, especially when individual studies have limited sample sizes or varying outcomes. It uses statistical techniques to calculate an overall effect size (ES), allowing researchers to determine the strength and consistency of a relationship across different contexts. There is a powerful combination between systematic reviews and meta‐analyses for understanding a body of research.

This paper provides systematic literature review on use of RCBP in concrete. The aim is to gain clear understanding and draw lessons from the existing body of research. Furthermore, the paper explores gaps in the literature that could inform future research directions. A carefully measured quantity of RCBP was mixed with dry cement, which was used to produce.

A meta‐analysis serves the purpose of quantitatively synthesizing results from multiple studies to derive a more precise estimate of the effect or relationship being examined. Meta‐analysis enhances statistical power and improves the reliability of the results, especially when individual studies have limited sample sizes or varying outcomes. It uses statistical techniques to calculate an overall ES, allowing researchers to determine the strength and consistency of a relationship across different contexts. There is a powerful combination between systematic reviews and meta‐analyses for understanding a body of research.

The focus of this is on the incorporation of RCBP in concrete. The key questions are aimed at addressing the mechanical performance and environmental sustainability of concrete containing RCBP using recycled materials in construction. These questions guide the review by focusing on critical aspects that influence the feasibility, effectiveness, and sustainability of using recycled bricks as a substitute for cement in concrete production.

  • •

    How does the incorporation of RCBP affect the mechanical and physical properties of concrete, including compressive, flexural, and tensile strengths as well as durability?

  • •

    What is the optimal percentage of cement replacement with RCBP such as the range of replacement percentages and threshold effects?

  • •

    What are the environmental impacts of utilizing RCBP to replace Portland cement?

2. Methodology

2.1. Search Strategy and Eligibility Criteria

Databases, search terms, and inclusion/exclusion criteria were used to select relevant studies for the systematic review. When conducting a systematic review with meta‐analysis, it is crucial to define precise search strategy and eligibility criteria to ensure that only the most relevant studies are included. A comprehensive search strategy is essential to capture relevant studies from web of science (WoS) database and sources to reduce publication bias and ensure the inclusion of diverse studies. The WoS databases is chosen to cover the literature relevant to the field of study for different reason.

  • ▪

    Web Science sources are open‐access journals that are freely available. WoS has advantages for Engineering reviews due to its rigorous indexing criteria and peer‐reviewed content.

  • ▪

    Web Science documents is a broader range of open‐access materials such as institutional repositories, government reports, and original articles. It is preferable, especially in developing countries or institutions with limited funding and lack of subscriptions.

  • ▪

    Web Science sources often feature preprints and real‐time research updates; therefore speedy accessible.

  • ▪

    Regional diversity is another factor that makes Web Science documents an attractive choice, which can lead to free bias.

In the search, keywords are defined to capture all relevant studies. A systematic search string typically combines keywords using Boolean operators (AND, OR, NOT). For this study, the PICO framework (population, intervention, comparison, outcome) was used to structure search terms. Population is concrete, whereas intervention is recycled waste bricks, and outcome is concrete performance, which is mechanical properties and durability. This study searched as all = (Recycled bricks OR Pulverized brick ∗ OR Waste Brick) AND (Cement Replacement) AND Concrete) is a searching engine.

2.2. Screening Process

The screening procedure entails systematic filtering and refinement of the collected dataset to ensure its accuracy, relevance, and methodological rigor. This phase commences with the formulation of explicit inclusion and exclusion criteria. In most cases, the analysis is restricted to peer‐reviewed journal articles, review papers, and conference proceedings, whereas duplicates, non‐English publications, and studies deemed irrelevant or misaligned with the predefined research objectives are excluded. Following this process, the final dataset is cleaned and structured to guarantee that only high‐quality, methodologically sound research contributions advance to the subsequent stage of the investigation.

2.3. Data Extraction Process and Statistical Analysis

A systematic literature search was undertaken using the electronic database of WoS from January 1st, 2014, to 2025. The search strategy included the use of terms in three broad categories, which are the combination of the recycled brick waste, the cement replacement, and its application directly to concrete. Title, abstract, and keywords were searched using: all = (Recycled bricks OR Pulverized brick ∗ OR Waste Brick) AND (Cement Replacement) AND (Concrete). To compile and analyze the available published information, a selection was made from the web science of categories such as Engineering, Civil; Material Science, Multidisciplinary; and Construction Building Technology.

To conduct further quantitative analysis, JASP (Jeffreys′ Amazing Statistics Program) was employed specifically for meta‐analysis. ES is calculated using Cohen′s formula based on the difference between the recycled brick replacement with cement and the control mixes (i.e., reference mix that does not incorporate RCBP). The ES is calculated using the following equations [15].

Effect size=mean treatment−mean controlstandard deviation, (1)

where mean treatment is the mean for data based on cement replacement by RCBP, mean control is the mean for data based on control mixes.

Sp=n11−S12+n21−S22n122+n−, (2)

where S p (pooled variance) is the standard deviation, S1 is the standard deviation based on cement replacement by recycled clay brick, S2 is the standard deviation based on control mixes n1 is the number of data based on cement replacement by recycled clay brick, n2 is the number of data based on control mixes. Fixed‐ and random‐effects of meta‐analyses were employed to check the variation of the variable under observation. A homogeneity test was also conducted to determine the deviation of the treated variables from the control variables. Figure 1 is illustrated about the general methodology structure of the systematic literature review.

Figure 1.

Figure 1

Structure of methodology.

2.4. Quality Assessment

To enhance rigor, transparency, and reliability, a formal quality assessment of included studies is conducted in accordance with Preferred Reporting Items for Systematic Reviews and Meta‐Analyses (PRISMA) guidelines. After identification and screening, all studies meeting the inclusion criteria underwent structured critical appraisal at the eligibility stage to evaluate the robustness of the evidence and reduce potential bias. Each study was assessed against predefined criteria: clarity of objectives, strength of experimental design, reliability and repeatability of data collection, and validity of analytical methods. Studies with clear methodologies, consistent results, and strong empirical support were classified as high quality and included for further analysis.

Publications lacking sufficient methodological detail, clear procedures, or unbiased data interpretation were scrutinized and excluded, when necessary, under PRISMA eligibility criteria, ensuring that only robust, credible studies entered the final dataset. Limiting sources to peer‐reviewed journal articles, review papers, and high‐quality conference proceedings further reinforced reliability. Bibliometric analysis with VOS viewer complemented this assessment by identifying influential, highly cited publications and key research clusters. Combining PRISMA‐guided systematic review with scientometric analysis strengthened the validity of the findings, minimized bias, and ensured that this study′s conclusions rest on high‐quality, reproducible, and impactful research.

3. Results of Systematic Review and Meta‐Analysis

3.1. Geographical Distribution and Key Studies

Countries of the authors and their citations are assessed and shown in Figures 2 and 3. Research on the replacement of cement by recycle of brick powder in PCC is globally distributed, with significant contributions from various countries such as China, Brazil, India, and United States. China has been a prominent contributor to publications on the topic, with studies focusing on the utilization of clay bricks as a sustainable alternative to cement in construction practices. There is a strong presence in research related to the replacement of cement by recycle clay brick powder, highlighting the global interest and importance of this subject in the construction industry. Publications from Brazil and India have also made notable contributions to the literature on the use of recycle brick as a substitute for Portland cement, indicating a widespread interest and research focus on sustainable building materials. Figure 2 illustrates the spatial distribution of documents under web science publication from 2014 to 25 February 2025.

Figure 2.

Figure 2

Publications distributions based on geographical location.

Figure 3.

Figure 3

Citation counts of countries from 2014–2025.

Publication in Asia are counted by republic of China, India, Malaysia, Iraq, Saud Arabia, and Pakistan are majorly contributed in the area, where as England and Spain are from Europe. Figure 3 also discusses the number of citations per country. China, United States, England, Brazil, and India have highly readable and cited journals about replacement of cement by recycled clay brick. Figure 3 illustrates the number of citations per country concerning research on the replacement of cement with recycled clay brick. The countries with the highest number of citations are China, the United States, Brazil, and India, which have made significant contributions to this research field.

There are so many key factors behind high citation counts in these countries. These countries have well‐established research institutions and universities actively publishing high‐impact studies on sustainable construction materials, including recycled clay bricks in cement production.

In addition, China, the United States, and India have extensive policies promoting eco‐friendly construction materials, encouraging researchers to explore alternatives to traditional cement. This high citation rate reflects global recognition of their contributions to sustainable construction materials, particularly the role of recycled clay brick in cement replacement.

Other publications have added to the global discourse on the replacement of cement by clay brick, with a considerable number of citations reflecting the country′s research contributions in this area from Africa, which is represented by Nigeria, Egypt, and Algeria. The United States from North America and Brazil from South America have major contribution from the continents.

Paper output has increased from 2014 to 2024, as illustrated in Figure 4, however it appears to be declining in 2019. The coronavirus might have had an impact on the publications of experimental papers. Over time, research publications about the substitution of clay brick for cement in the manufacturing of concrete have become more common, suggesting a growing interest in this environmentally friendly building method.

Figure 4.

Figure 4

Paper production and citation from 2014 to February 25, 2025.

In the following graphs as illustrated by Figure 5 are keywords that indicates the publication about waste brick replacing the cement.

Figure 5.

Figure 5

Author keywords and occurrence.

The use of clay bricks to replace Portland cement in the manufacturing of concrete has been emphasized by researchers to increase sustainability in the building sector and lower its negative effects on the environment. The prevalence of author keywords centered on using clay bricks rather than cement in the construction of concrete illustrates a global trend toward the use of environmentally friendly building materials and techniques.

3.2. PRISMA Protocol and Diagram

In 2009, an international group of systematic reviewers and journal editors introduced the PRISMA statement, a guideline aimed at assisting authors in preparing comprehensive reports of their systematic reviews. The PRISMA 2009 statement comprised 27 checklist items, representing the minimum necessary information for systematic review reports [16]. The PRISMA 2020 statement was primarily developed for systematic reviews; however, its checklist items are also applicable to reports evaluating various interventions, including social or educational interventions. Additionally, many of its items are relevant to systematic reviews with diverse objectives [17–19]. PRISMA 2020 is intended for use in systematic reviews that incorporate synthesis methods, such as pairwise meta‐analysis or other statistical approaches [20].

Figure 6 presents the PRISMA 2020 flow diagram, which was designed using Biblioshiny to illustrate the systematic review process after screening abstracts and full‐text articles through Covidence. Initially, 98 articles were identified based on relevant identification and screening criteria. These articles underwent a rigorous screening process in Covidence, where both abstract and full‐text evaluations were conducted to determine their suitability for inclusion. Following this assessment, 53 articles were selected for the final study report. The PRISMA 2020 flow diagram visually represents the stages of article selection, including identification, screening, eligibility assessment, and inclusion, providing a clear overview of the systematic review process.

Figure 6.

Figure 6

PRISMA flow diagram using Biblioshiny.

3.3. Meta‐Analysis Results

3.3.1. ES of the Meta‐Analysis

This section reflects the actual studies collected for the meta‐analysis, including statistical details such as ES, p values, or confidence intervals. For a meta‐analysis on the effect of replacing cement with recycled bricks on concrete strength, there is a clear comparison between different studies, helping to analyze the overall effect of recycled brick replacement on concrete strength. In this study, different concrete mixes such as normal concrete, high‐strength concrete, and lightweight concrete are used based on the types of ingredients/aggregates and additional admixtures. The percentage of RCBP is also identified. The control group strength, which is the compressive strength of the control group without recycled brick and experimental group strength with sample size tested in each study are considered as indicated in Table 1.

Table 1.

The fixed and random effect of compressive strength meta‐analysis.

Fixed and random effects
Q df p
Omnibus test of model coefficients 14.965 1 < 0.001
Test of residual heterogeneity 21549.122 32 < 0.001

Note: p values are approximate. The model was estimated using restricted ML method.

The curing period of the concrete and the ES, which is a standardized measure of the difference between the control and experimental groups are calculated using Cohen′s d formula. In addition, the confidence interval around the ES is used in the meta‐analysis. In a forest plot for meta‐analysis, the goal is to visualize the ESs of multiple studies, typically with a confidence interval. Figure 7 is rearranged in a manner that aligns with the input required for generating a forest plot. The columns for the forest plot contain the percentage of cement replacements by RCBP. In meta‐analysis, ES (Cohen′s d), standard error (SE), 95% confidence interval (lower), 95% confidence Interval (upper), and weight (%) of each study in the meta‐analysis are based on sample size and precision.

Figure 7.

Figure 7

The effect size of the meta‐analysis for performance based on cement replacement.

The findings from the meta‐analysis underscore a significant and consistent negative impact on the compressive strength of concrete when cement is replaced with RCBP. As the percentage of RCBP content increases, there is a noticeable decline in compressive strength, with the reduction becoming more pronounced at higher replacement levels [2, 21, 22].

3.3.2. Fixed Random Effect and Residual Heterogeneity Estimates

Table 1 shows the results of the Omnibus test of model coefficients. The chi‐square (χ2) value of 14.865, degrees of freedom (df) of 1, and a p value of p < 0.001, indicating a statistically significant result. The Omnibus test confirms that the model coefficients significantly improve the model fit. The intercept′s confidence interval does not include zero, reinforcing its significance in the model. The significant p value in the Omnibus test suggests that the model with these coefficients provides a better fit than a model without them. Test of residual heterogeneity with a Q = 21,549.122, df = 32, and p < 0.001, suggesting significant residual heterogeneity.

Table 2 shows the lower and upper coefficients with 95% confidence interval. The t intercept estimate is −5.257, the SE equals 1.35, and the 95% confidence interval ranging from −7.921 to −2.594, suggests a strong negative effect. The negative interception might indicate a baseline tendency in the dependent variable when all predictors are at zero point.

Table 2.

Coefficients with 95% confidence interval.

Coefficients
95% confidence interval
Estimate Standard error z p Lower Upper
Intercept −5.257 1.359 −3.868 < 0.001 −7.921 −2.594

Note: Wald test.

Table 3 shows residual heterogeneity and refers to the differences that remain in a study after accounting for certain variables. The table indicates the variation exists among the results of different studies. The table presents estimates of residual heterogeneity using different statistical measures. The first one is “Estimate” which shows the calculated value for each measure. The second column is the “Lower” which indicates the lower limit of the 95% confidence interval whereas column marked as “Upper” shows the upper limit of the 95% confidence interval. The confidence interval gives a range in which one can be 95% sure the true value lies.

Table 3.

Residual heterogeneity estimates.

Residual heterogeneity estimates
95% confidence interval
Estimate Lower Upper
T2 59.720 38.004 103.802
T 7.728 6.165 10.188
I2(%) 99.632 99.423 99.788
H2 271.587 173.196 471.324

T 2 (Tau‐squared) value is a measure of the variance among the study results. The higher the T 2 value indicates higher variability. For T 2 value of 59.72, the lower limit is 38.004 and the upper limit is 103.802, which means 95% confident that the true variance lies between these two values. T (Tau) is the square root of T 2 and represents the standard deviation of the true effects, which measure how much the study results differ from each other. H 2 (Heterogeneity) is another measure of heterogeneity that indicates how much the results vary. An H 2 value of 271.6 is suggestive of a high heterogeneity level. The confidence interval ranges from 173.2 to 471.3, showing a wide range of possible true values which helps to assess the reliability of findings.

These findings suggest that while using RCBP as a partial Portland cement replacement may be a sustainable solution for reducing waste and promoting circular economy practices; however, it may not be suitable for applications where high‐strength concrete is required.

As we concur that from Table 3, the very high heterogeneity (I 2 = 99.632%) indicates substantial between‐study variability arising from differences in concrete type, mix proportions, curing conditions, replacement levels, and material characteristics, rather than sampling error alone. The intention of the study is to perform the overall random‐effects meta‐analysis; it is not to imply that all concrete systems exhibit identical behavior, but rather to estimate the average effect across the broad spectrum of published applications of RCBP.

The pooled effect estimate should be interpreted with considerable caution, as the mechanisms governing the influence of RCBP differ markedly among normal‐strength concrete, lightweight aggregate concrete, and ultrahigh‐performance concrete (UHPC). In UHPC, filler effects and optimized particle packing constitute the dominant mechanisms, whereas in conventional concrete systems, dilution effects and pozzolanic reactions are more influential. The extremely high degree of heterogeneity (I 2 = 99.632%) has substantial practical implications, indicating that the synthesized pooled effect reflects merely an average tendency across highly diverse experimental conditions, rather than a universally generalizable material response. Consequently, the reliability of the pooled estimate for predicting the performance of any specific concrete mixture is constrained, and direct use of the mean ES for engineering design or material selection should be avoided without explicit consideration of project‐specific conditions. Instead, practitioners should interpret the synthesized results in conjunction with concrete type, RCBP replacement level, constituent material properties, and curing conditions.

To address this limitation, statistical interpretation has been broadened to explicitly account for the influence of heterogeneity between studies on both the reliability and the external validity of the pooled estimate. Where data density permitted, subgroup analyses stratified by concrete type and RCBP replacement level were conducted to more clearly differentiate the behavior of distinct concrete categories. Nonetheless, the pooled random‐effects estimate should not be construed as a single predictive value that is uniformly applicable across all concrete systems.

Future investigations should implement meta‐regression models incorporating parameters such as water‐to‐binder ratio, concrete type, replacement percentage, curing regime, and RCBP characteristics to better elucidate the sources of between‐study variability and to enhance the precision and practical relevance of subsequent pooled estimates.

3.3.3. Funnel Plot of the Meta‐Analysis

A funnel plot is an important tool in meta‐analysis, used to assess the potential bias in the concerned studies. It can help determine whether smaller studies show different or more extreme results compared with larger studies, which may indicate potential publication bias. Furthermore, it allows examining the relationship between the study size and its results. For concrete compressive strength of concrete containing RCBP, the funnel plot can provide valuable insights into the reliability of the findings from various studies included in the analysis.

Figure 8 shows the funnel plot of meta‐analysis. The horizontal axis (ES) of the funnel plot represents the impact of RCBP replacement on the compressive strength of concrete. As observed in the meta‐analysis, a negative ES suggests a reduction in compressive strength as the RCBP percentage increases. Higher RCBP percentage results in a more significant reduction in concrete strength.

Figure 8.

Figure 8

Funnel plot of meta‐analysis.

The vertical axis (study size or precision) represents larger studies tend to have higher precision (i.e., less random error), meaning their results are more reliable. Smaller studies tend to have lower precision, which is prone to random error. If there is no bias, the studies should ideally show a symmetrical distribution around the ES, forming a funnel shape. This study is large being more precise, which would cluster near the center of the plot, where the ES is more accurately estimated. The funnel plot would appear asymmetrical, with more studies clustered on one side of the plot, which shows a greater reduction in strength and fewer studies on the other side, distorting the shape of the funnel. The symmetrical funnel plot supports the robustness of the observed reduction in compressive strength with increasing RCBP replacement, consistent across small and large studies. Another key meta‐analysis and visualization tool is the radial (spider or radar) plot, used to compare multiple variables simultaneously. Figure 9 shows a radial plot illustrating the effects of RCBP replacement percentage and curing period. Each variable appears on an axis radiating from a central point. A larger, more uniform shape indicates good performance across variables, with relatively high compressive strength even at higher RCBP contents, whereas a smaller or irregular shape suggests weaknesses, such as a marked strength drop at high RCBP levels.

Figure 9.

Figure 9

Radial and normal Q–Q plot.

The normal Q‐Q plot helps to assess whether the data follows a normal distribution, which is a key assumption for many statistical tests. The effect of RCBP replacement on concrete′s compressive strength is evaluated, with a normal Q–Q plot used to assess whether the data on compressive strength at different levels of clay brick replacement follows a normal distribution.

4. Discussion of Main Results

4.1. Performance of Concrete With RCBP

The incorporation of RCBP into concrete affects the strengths properties when used as a partial replacement for cement. Studies have shown that replacing cement with up to 25% RCBP by mass, in combination with waste glass as a sand replacement, can help reduce CO2 emissions in concrete production [23]. The substitution of RCBP 5%, 10%, or 20% waste powder as a partial cement replacement has been tested [24] [25]. The observed reduction in strength may be attributed to the low amorphous content of brick dust and the presence of unreacted brick dust particles [26].

The compressive strength of concrete was improved by the replacement with brick waste to a percentage less than 10% by weight at all curing ages. It started to decline as cement percentage reached 15% by weight at all curing ages; however it was still higher than that of the reference concrete [7, 27]. The compressive strength of the UHPC decreased with the increase in replacement rate after the cement was replaced by activated recycled brick powder, and the decreasing trend was more obvious with older age [28]. RCBP replacement effectiveness might be affected by the finesse of particles. The high water‐binder ratio makes it more vulnerable to damage caused by water migration, which reduces the bonding performance between mortar and aggregate, resulting in a faster decrease in compressive strength [29]. The waste concrete powder is mainly composed of quartz, calcite, and sodium feldspar, and the waste bricks powder is primarily composed of quartz, aluminum oxide, and hematite [30]. Clay brick waste is reutilized in mortar/concrete as cement replacement after grinding [4]. Recycled clay bricks possess the required chemical compositions for a binder substitute [31, 32].

Several studies have explored the use of RCBP as a partial replacement for cement in concrete mixtures, with replacement percentages typically ranging from 10% to 40% mass. Reducing the need for natural resources, such as aggregates and cement, which have high environmental costs in their extraction and production [33, 34]. Cement production itself is highly resource‐intensive, contributing significantly to global CO2 emissions. The process consumes vast amounts of natural resources, particularly in the form of aggregates, and requires considerable energy for the clinker firing process [35, 36]. As the construction industry seeks to reduce its carbon footprint, replacing a portion of cement with alternative materials such as RCBP presents a promising solution. The use of waste materials like brick powder or fly ash helps lower energy consumption, cut material costs, and reduce greenhouse gas emissions associated with cement production [37, 38] [39].

The influence of RCBP on concrete performance is context‐dependent rather than intrinsically beneficial or detrimental. Existing research demonstrates that the impact of RCBP is controlled by a set of interrelated parameters, including replacement ratio, curing duration and conditions, particle fineness, and the chemical and mineralogical composition of the brick powder [6, 40]. At low to moderate replacement levels (generally on the order of 5%–15%, and in some cases up to 20% depending on material quality), finely ground RCBP can enhance long‐term strength development via pozzolanic reactions and microfiller effects. Conversely, higher replacement levels or the use of coarser or highly crystalline RCBP tend to dilute the cementitious matrix and impair early‐age mechanical properties. Consequently, broad generalizations regarding the performance of RCBP should be avoided, as its efficacy is strongly contingent upon the properties of the source material and the specific concrete mix design [41].

Furthermore, curing conditions play a critical role in determining the extent of pozzolanic activity. Adequate moist curing promotes the reaction between the amorphous silica and alumina present in RCBP and calcium hydroxide released during cement hydration, leading to the formation of additional calcium silicate hydrate (C–S–H) gel and improved long‐term performance [42]. Conversely, inadequate curing may suppress these beneficial reactions and result in lower strength and durability. Accordingly, the conclusions should explicitly state that the engineering performance of RCBP cannot be generalized across all applications but should instead be interpreted in relation to replacement ratio, curing regime, particle fineness, and the physicochemical properties of the recycled brick powder.

Waste clay brick is a major component of construction and demolition waste [43]. Recycling brick powder into concrete not only reduces waste but also addresses the growing concerns about landfill space and the environmental impacts. Additionally, the substitution of cement with recycled brick powder can help mitigate the depletion of natural resources and minimize the negative environmental effects of cement manufacturing [44].

While using firebrick waste as a cement replacement slightly reduced the compressive strength of concrete at 28 days, its use as a sand substitute improved the thermal properties of the material [45, 46]. The use of glass and brick powder waste together has also proven to be an effective strategy for addressing environmental pollution and reducing the demand for resources [47–50].

Studies have also examined the mechanical properties of concrete incorporating recycled brick powder. However, increasing the replacement percentage beyond this point resulted in a decrease in strength [51–54]. This suggests that although a moderate amount of recycled brick powder can improve concrete properties, excessive replacement may negatively impact its mechanical performance [55–58]. The pozzolanic activity of brick powder, which contributes to the strength of concrete, typically takes time to develop, with significant effects observed between 7 and 28 days of curing [59–61]. In other experiments, researchers found that incorporating up to 20% recycled brick powder as a clinker replacement could maintain or even improve the microstructure, durability, and mechanical properties of mortars [62, 63].

Replacing the cement with wastes and dust in 2.5% different proportion of 5%, 7.5%, 10%, 12.5%, 15%, 20% has also been studied [28, 64–66]. At higher replacement rates, which are 30%–40%, the compressive and flexural strengths of the concrete completely decline [67, 68]. However, the use of recycled sand and brick waste has shown improvements in flexural and adhesive strength while reducing permeability [69, 70]. Therefore, it is important to carefully balance the amount of brick powder used to optimize both performance and sustainability.

4.2. Challenges and Future Directions

Future research could explore the optimization of the clay brick waste‐to‐cement ratio, investigate potential treatments to enhance the performance of clay bricks in concrete. Additionally, it should examine other supplementary materials that could offset the strength loss associated with clay brick powder replacement. However, the construction industry should move toward more environmentally friendly solutions without compromising structural integrity. The replacement of Portland cement by RCBP is an intriguing area of research and development, especially in sustainable construction practices [39].

Key challenges and future directions for using RCBP as a cement replacement must be identified. The mechanical strength of cement‐based materials can differ significantly from concrete with RCBP. Cement generally offers higher compressive strength but may lack the thermal and acoustic advantages of RCBP. When processing and incorporating RCBP into cement matrices, adjustments are often required to meet the structural performance needs of specific construction applications. These challenges and future directions for using RCBP in concrete production are summarized in Table 4.

Table 4.

Challenges and future direction about clay brick powder replacement into cement.

Term Description Challenges Future directions
Material properties Characteristics of the materials (strength, durability, thermal properties). There is a lack of thermal/acoustic properties of cement concrete. Develop cement‐recycled clay brick powder composites to balance strength, insulation, and acoustic properties.
Cement is prone to cracking and is sensitive to environmental factors. Explore self‐healing concrete technologies that repair microcracks and improve durability with pozzolanic replacement.
Environmental impact The environmental footprint of both cement production and the recycling of clay bricks. Cement production is highly energy‐intensive and contributes significantly to CO2 emissions. Low‐carbon alternatives such as recycled clay powder—cement to reduce the carbon footprint of cement‐based materials.
Recycling processes can have high environmental costs. Improve energy efficiency and reduce environmental costs of recycling processes.
Economic viability Involves the economic feasibility of using recycled clay bricks in cement‐based products. The integration of recycled clay bricks into cement may be costly Develop more efficient and affordable recycling technologies for clay bricks.
The supply chain for both cement and recycled clay materials can be inefficient and costly. Improve local sourcing and supply chains to reduce transportation and logistical costs.
Regulatory and standardization The established codes, regulations, and standards that guide construction materials. Current building codes and regulations may not account for the use of recycled clay. Establish standards for recycled content: develop guidelines to safely incorporate recycled materials in construction.
Ensuring recycled clay brick materials meet safety, strength, and durability standards. Engage industry stakeholders, researchers, and regulators to update standards.
Technical and structural integrity Recycled clay bricks can be incorporated into cement‐based materials, ensuring they perform effectively in construction applications. Recycled clay bricks may not integrate well with cement, leading to potential issues like shrinkage or poor adhesion. Research needs new method of crushing, grinding, and integrated to improve the compatibility of clay bricks and cement.
Developing the right mix to ensure recycled clay bricks do not compromise cement performance. Investigate and optimize the cement‐clay brick mix to enhance strength.
Innovation Using new or advanced materials Cement materials may not have the necessary additives to enhance performance. Incorporate nanomaterials to improve bonding and the overall performance of recycled cement mixtures.

It is highly recommended for researchers to explore the use of hybrid materials where recycled clay bricks are combined with advanced cementitious binders, including geopolymer cement, to optimize mechanical strength, thermal insulation, and durability.

The engineering significance of this study lies in providing quantitative evidence that RCBP can function as a sustainable supplementary cementitious material, thereby contributing to waste valorization, the implementation of circular economy principles, and the reduction in Portland cement consumption. The meta‐analysis indicates that, although the incorporation of RCBP generally leads to a decrease in compressive strength, its mechanical performance is strongly influenced by the replacement level, particle fineness, curing conditions, and the type of concrete. Consequently, the use of RCBP should be governed by performance‐based mix design methodologies rather than by the adoption of a single, universal replacement ratio.

The practical applications component develops engineering guidelines and design recommendations for the safe and effective use of RCBP in concrete. It specifies recommended replacement ratios for structural and nonstructural applications based on mechanical, durability, and serviceability performance. It also supports the formal inclusion of RCBP in national concrete standards, design codes, and sustainability frameworks once sufficient performance data and long‐term field evidence are available. To achieve this, the framework promotes collaboration among researchers, industry, and policymakers to define standardized quality control, certification schemes, and compliance testing, enabling large‐scale, reliable use of recycled brick waste in construction. It further embeds RCBP within circular construction strategies by linking demolition waste recycling to new concrete production, thereby reducing landfill disposal, conserving primary raw materials (e.g., natural aggregates and clinker), and lowering life‐cycle greenhouse gas emissions from the built environment.

Recommendations for future research include the following:

  • ▪

    Conduct comprehensive and systematic experimental programs to identify the optimum RCBP replacement levels for various concrete strength classes, including normal‐strength, high‐strength, and UHPC, with consideration of both fresh and hardened properties as well as long‐term performance.

  • ▪

    Investigate the synergistic effects of RCBP in combination with other supplementary cementitious materials (e.g., fly ash, silica fume, ground granulated blast‐furnace slag, limestone powder, and calcined clays) to optimize mechanical properties and durability performance, including resistance to chemical attack, permeability, and long‐term microstructural stability.

  • ▪

    In future meta‐analyses, employ meta‐regression techniques to quantitatively evaluate the influence of key independent variables such as water‐to‐binder ratio, RCBP replacement level, curing regime, particle fineness, chemical and mineralogical composition, and concrete strength class on compressive strength and other relevant performance indicators, with the objective of reducing unexplained heterogeneity, improving the robustness of statistical inferences, and enhancing the predictive capability of empirical models.

5. Conclusion

This systematic review and meta‐analysis are aimed at comprehensively assessing the use of recycled brick waste powder as a cement replacement in concrete as a sustainable alternative.

  • ▪

    Vow Viewer, JASP was utilized to estimate the geographical distribution of documents and ESs based on the differences between concrete mixes containing recycled brick and control mixes without cement substitution.

  • ▪

    Majorly China, India, United States, and Brazil are concerned about the cement issues and they have publications regarding to cement replacement.

  • ▪

    The findings indicate a systematic and statistically significant reduction in the compressive strength of concrete when clay brick particles are employed as a partial substitute for cement. Nevertheless, the extant literature shows that the influence of RCBP is governed by a set of interdependent parameters, including the replacement ratio, curing duration and conditions, particle fineness, as well as the chemical and mineralogical characteristics of the brick powder.

  • ▪

    As the proportion of clay brick content increases with higher replacement level, the decrease in compressive strength becomes more pronounced.

  • ▪

    The forest plot provides a clear visual representation of the ES across different studies, illustrating both the magnitude and variability of strength reduction.

In addition, more research could focus on optimizing the clay brick‐to‐cement ratio to minimize strength loss, as well as exploring potential treatments or modifications to enhance the performance of clay bricks in concrete. Additionally, investigating alternative supplementary materials that could mitigate the negative effects of clay brick replacement may offer further opportunities for sustainable construction practices.

This study considers the limitations of using single search engine. The primary search strategy focused on WoS due to constraints in integrating data from multiple databases into analysis with VOS viewer software.

Funding

No funding was received for this manuscript.

Conflicts of Interest

The authors declare no conflicts of interest.

Mitikie, Bahiru Bewket , Elsaigh, Walied A. , Chabalala, Dunisani Thomas , Systematic Review and Meta‐Analysis of Recycled Brick Powder as a Partial Replacement for Portland Cement (2014–2025), The Scientific World Journal, 2026, 2771399, 16 pages, 2026. 10.1155/tswj/2771399

Academic Editor: Deepali Deepali

Contributor Information

Bahiru Bewket Mitikie, Email: mitikbb@unisa.ac.za.

Deepali Deepali, Email: dedeepali@wiley.com.

Data Availability Statement

The data that support the findings of this study are available on request from the corresponding author. The data are not publicly available due to privacy or ethical restrictions.

References

  • 1. Amin A., Recycle of Wastes of Clay Brick Industry for Producing Eco-Cement, 2010, Energy Systems Laboratory. [Google Scholar]
  • 2. Kim J., Lee D., Sičáková A., and Kim N., Utilization of Different Forms of Demolished Clay Brick and Granite Wastes for Better Performance in Cement Composites, Buildings. (2023) 13, no. 1, 10.3390/buildings13010165. [DOI] [Google Scholar]
  • 3. Salli Bideci Ö., Bideci A., and Ashour A., Utilization of Recycled Brick Powder as Supplementary Cementitious Materials—A Comprehensive Review, Materials. (2024) 17, no. 3, 10.3390/ma17030637, 38591483. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 4. Li L., Lin Z., Chen G., Kwan A., and Li Z., Reutilization of Clay Brick Waste in Mortar: Paste Replacement Versus Cement Replacement, Journal of Materials in Civil Engineering. (2019) 31, no. 7, 04019129, 10.1061/(ASCE)MT.1943-5533.0002794. [DOI] [Google Scholar]
  • 5. Mekonen W. W., Mitkie B. B., and Lakew E. M., Experimental Investigation on Partial Replacement of River Sand With Waste Brick and Laterite Soil in Concrete Production, Journal of Civil, Construction and Environmental Engineering. (2025) 10, no. 4, 166–174, 10.11648/j.jccee.20251004.14. [DOI] [Google Scholar]
  • 6. Wu H., Liang C., Wang C., and Ma Z., Properties of Green Mortar Blended With Waste Concrete-Brick Powder at Various Components, Replacement Ratios and Particle Sizes, Construction and Building Materials. (2022) 342, 128050, 10.1016/j.conbuildmat.2022.128050. [DOI] [Google Scholar]
  • 7. Resin R., Alwared A., and Al-Hubboubi S., Utilization of Brick Waste as Pozzolanic Material in Concrete Mix, Matec Web of Conferences, 2018, 162, EDP Sciences, 02006, 10.1051/matecconf/201816202006. [DOI] [Google Scholar]
  • 8. Olofinnade O., Ede A., and Booth C., Sustainability of Waste Glass Powder and Clay Brick Powder as Cement Substitute in Green Concrete, Handbook of Environmental Materials Management, 2018, 1–22, 10.1007/978-3-319-58538-3_112-1. [DOI] [Google Scholar]
  • 9. Barthel M., Rübner K., Kühne H.-C., Rogge A., and Dehn F., From Waste Materials to Products for Use in the Cement Industry, Advances in Cement Research. (2016) 28, no. 7, 458–468, 10.1680/jadcr.15.00149. [DOI] [Google Scholar]
  • 10. De Queiroz Lamas W., Palau J. C. F., and De Camargo J. R., Waste Materials Co-Processing in Cement Industry: Ecological Efficiency of Waste Reuse, Renewable and Sustainable Energy Reviews. (2013) 19, 200–207, 10.1016/j.rser.2012.11.015. [DOI] [Google Scholar]
  • 11. Makó É. and Őze C., The Effects of Silica Fume and Diatomaceous Earth on the Mechanochemical Activation and Pozzolanic Activity of Kaolin, Applied Clay Science. (2022) 228, 106636, 10.1016/j.clay.2022.106636. [DOI] [Google Scholar]
  • 12. Siddique R. and Klaus J., Influence of Metakaolin on the Properties of Mortar and Concrete: A Review, Applied Clay Science. (2009) 43, no. 3-4, 392–400, 10.1016/j.clay.2008.11.007. [DOI] [Google Scholar]
  • 13. Szeto C., Innovations in Characterization and Design of Durable Sustainable Cementitious Systems Utilizing Pozzolanic Materials, 2025, Georgia Institute of Technology ProQuest Dissertations & Theses. [Google Scholar]
  • 14. Yang-hee K., Effect of Intensified Pozzolanic Reaction and Thermal Treatment on Properties of Cementless Composites, 2017, Seoul National University Graduate School. [Google Scholar]
  • 15. Anwar F. H., El-Hassan H., and Hamouda M., A Meta-Analysis on the Performance of Pervious Concrete With Partial Cement Replacement by Supplementary Cementitious Materials, 8th Zero Energy Mass Custom Home International Conference, ZEMCH 2021, 2021, ZEMCH Network, 747–753. [Google Scholar]
  • 16. Page M. J., Mckenzie J. E., Bossuyt P. M., Boutron I., Hoffmann T. C., Mulrow C. D., Shamseer L., Tetzlaff J. M., and Moher D., Updating Guidance for Reporting Systematic Reviews: Development of the PRISMA 2020 Statement, Journal of Clinical Epidemiology. (2021) 134, 103–112, 10.1016/j.jclinepi.2021.02.003, 33577987. [DOI] [PubMed] [Google Scholar]
  • 17. Mitikie B. B. and Elsaigh W. A., AI-Driven Bibliometric Analysis of Bacterial Concrete Research (2020–2025), Technologies. (2026) 14, no. 6, 10.3390/technologies14060340. [DOI] [Google Scholar]
  • 18. Page M. J., Mckenzie J. E., Bossuyt P. M., Boutron I., Hoffmann T. C., Mulrow C. D., Shamseer L., Tetzlaff J. M., Akl E. A., and Brennan S. E., The PRISMA 2020 Statement: An Updated Guideline for Reporting Systematic Reviews, British Medical Journal. (2021) 372, 10.1136/bmj.n71, 33782057. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 19. Tugwell P. and Tovey D., PRISMA 2020, 2021, 134, Elsevier, 10.1016/j.jclinepi.2021.04.008. [DOI] [Google Scholar]
  • 20. Mitikie B. and Elsaigh W., Application and Challenges of Biopolymers in Sustainable Construction: Through Scientometric Analysis and Systematic Review, Engineering Materials, Structures, Systems and Methods for a More Sustainable Future, 2025, CRC Press, 1640–1645, 10.1201/9781003677895-276. [DOI] [Google Scholar]
  • 21. Shao J., Gao J., Zhao Y., and Chen X., Study on the Pozzolanic Reaction of Clay Brick Powder in Blended Cement Pastes, Construction and Building Materials. (2019) 213, 209–215, 10.1016/j.conbuildmat.2019.03.307. [DOI] [Google Scholar]
  • 22. Tang Q., Ma Z., Wu H., and Wang W., The Utilization of Eco-Friendly Recycled Powder From Concrete and Brick Waste in New Concrete: A Critical Review, Cement and Concrete Composites. (2020) 114, 103807, 10.1016/j.cemconcomp.2020.103807. [DOI] [Google Scholar]
  • 23. Letelier V., Tarela E., and Moriconi G., Mechanical Properties of Concretes With Recycled Aggregates and Waste Brick Powder as Cement Replacement, Procedia Engineering. (2017) 171, 627–632, 10.1016/j.proeng.2017.01.396. [DOI] [Google Scholar]
  • 24. Tawfik T. A., Sičáková A., Kuzielová E., Kušnír Š., Eštoková A., Bálintová M., and Junáková N., Sustainable Reuse of Waste Ceramic Tiles Powder and Waste Brick Powder as a Replacement for Cement on Green High Strength Concrete Properties, Innovative Infrastructure Solutions. (2024) 9, no. 5, 10.1007/s41062-024-01498-2. [DOI] [Google Scholar]
  • 25. Yao P., Yang D., Wang C., and Ma Z., Upcycling of Construction Waste Powder for Sustainable Ultra-High Performance Engineered Cementitious Composites: Effects of Waste Powder Source and Content, Construction and Building Materials. (2022) 349, 128789, 10.1016/j.conbuildmat.2022.128789. [DOI] [Google Scholar]
  • 26. Ge Z., Wang Y., Sun R., Wu X., and Guan Y., Influence of Ground Waste Clay Brick on Properties of Fresh and Hardened Concrete, Construction and Building Materials. (2015) 98, 128–136, 10.1016/j.conbuildmat.2015.08.100. [DOI] [Google Scholar]
  • 27. Zhang Z., Liu X., Hu R., Liang C., Zhang Y., and Ma Z., Mechanical Behavior of Sustainable Engineered Cementitious Composites With Construction Waste Powder as Binder and Sand Replacement, Construction and Building Materials. (2023) 404, 133185, 10.1016/j.conbuildmat.2023.133185. [DOI] [Google Scholar]
  • 28. Yuan C., Chen Y., Liu D., Lv W., and Zhang Z., The Basic Mechanical Properties and Shrinkage Properties of Recycled Micropowder UHPC, Materials. (2023) 16, no. 4, 10.3390/ma16041570, 36837198. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 29. Qiu J., Niu G., Li L., Hu X., and Li X., Study on Damage Evolution Law and Pore Structure Deterioration of Recycled Composite Micro-Powder Concrete Under Freeze-Thaw Action, Journal of Building Engineering. (2024) 96, 110662, 10.1016/j.jobe.2024.110662. [DOI] [Google Scholar]
  • 30. Zhang H., Zhang C., He B., Yi S., and Tang L., Recycling Fine Powder Collected From Construction and Demolition Wastes as Partial Alternatives to Cement: A Comprehensive Analysis on Effects, Mechanism, Cost and CO2 Emission, Journal of Building Engineering. (2023) 71, 106507, 10.1016/j.jobe.2023.106507. [DOI] [Google Scholar]
  • 31. Elsaigh W. A., Tshetlanyane P. A., Asteray D. B., and Mitikie B. B., Sustainable Construction Materials: Potential Use of Pulverised Burnt Clay Bricks as a Partial Replacement of Portland Cement, RILEM Annual Week, 2026, Springer, 116–124, 10.1007/978-3-032-27919-4_15. [DOI] [Google Scholar]
  • 32. Olofinnade O., Ede A., Ndambuki J., Omole D., Francis P., Chigere C., and Oyeyemi K., Reuse of Pulverized Fired Clay Brick Wastes as Cement Substitute in Mortar for Sustainable Construction, IOP Conference Series: Materials Science and Engineering, 2019, 652, no. 1, IOP Publishing, 012048, 10.1088/1757-899X/652/1/012048. [DOI] [Google Scholar]
  • 33. Xiong W., Zhu H., Xu J., Ma J., and Luo C., Experimental Investigation on Physical and Mechanical Properties of Excavated soil- and Fine Recycled Concrete Aggregate-Based Unfired Clay Bricks Containing Compound Additives, Case Studies in Construction Materials. (2023) 18, e02057, 10.1016/j.cscm.2023.e02057. [DOI] [Google Scholar]
  • 34. Yaseen M. H., Hashim S. F. S., Dawood E. T., and Johari M. A. M., Mechanical Properties and Microstructure of Roller Compacted Concrete Incorporating Brick Powder, Glass Powder, and Steel Slag, Journal of the Mechanical Behavior of Materials. (2024) 33, no. 1, 20220307, 10.1515/jmbm-2022-0307. [DOI] [Google Scholar]
  • 35. Mitikie B. B., Kebede D. L., and Elsaigh W. A., Sustainable Mortar Production Using Volcanic Ash and Crushed Laterite as Partial Cement Replacements, Cement. (2025) 23, 100162, 10.1016/j.cement.2025.100162. [DOI] [Google Scholar]
  • 36. Szeląg M., Styczeń J., Fediuk R., and Polak R., Properties and Strength Prediction Modeling of Green Mortar With Brick Powder Subjected to a Short-Term Thermal Shock at Elevated Temperatures, Materials. (2021) 14, no. 21, 10.3390/ma14216331, 34771857. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 37. Cui L., Hu G., Pan J., Zhang X., Wang L., Wang H., and Mapulanga L., Enhancement Mechanical Performance of Brick Powder-Cement Mortar With Bio-Inspired Material, Construction and Building Materials. (2024) 432, 136397, 10.1016/j.conbuildmat.2024.136397. [DOI] [Google Scholar]
  • 38. Hao L., Xiao J., Cao W., and Sun J., Experimental Study and Assessment of Thermal Energy Storage Mortar With Paraffin/Recycled Brick Powder Composite Phase Change Materials, Frontiers of Structural and Civil Engineering. (2022) 16, no. 10, 1301–1314, 10.1007/s11709-022-0883-4. [DOI] [Google Scholar]
  • 39. Şenol A. F. and Karakurt C., High-Strength Self-Compacting Concrete Produced With Recycled Clay Brick Powders: Rheological, Mechanical and Microstructural Properties, Journal of Building Engineering. (2024) 88, 109175, 10.1016/j.jobe.2024.109175. [DOI] [Google Scholar]
  • 40. Chaitanya B. K., Sri Durga C. S., Thatikonda N., Mitikie B. B., Madhavi Y., and Venkatesh C., Integration of Machine Learning and Microstructural Characterization for Strength Forecasting With Silica Fume and M-Sand for Sustainable Concrete, 2026, 16, no. 1, Scientific Reports, 10.1038/s41598-026-43410-1. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 41. Li S., Chen G., Xu Z., Luo X., and Gao J., Particle-Size Effect of Recycled Clay Brick Powder on the Pore Structure of Blended Cement Paste, Construction and Building Materials. (2022) 344, 128288, 10.1016/j.conbuildmat.2022.128288. [DOI] [Google Scholar]
  • 42. Zhu X., Morphology-Structural Change of Calcium Silicate Hydrates, 2021, University of Leeds. [Google Scholar]
  • 43. Tang W., Chen P., Lin Z., Zhang L., Zheng W., Huang X., Zhang J., and Zhang W., Effectively Reutilizing Waste Clay Brick to Prepare A Novel Green Foam Concrete Base on a New Two-Step Paste Substitution Method, Construction and Building Materials. (2023) 372, 130794, 10.1016/j.conbuildmat.2023.130794. [DOI] [Google Scholar]
  • 44. Arif R., Khitab A., Kirgiz M. S., Khan R. B. N., Tayyab S., Khan R. A., Anwar W., and Arshad M. T., Experimental Analysis on Partial Replacement of Cement With Brick Powder in Concrete, Case Studies in Construction Materials. (2021) 15, e00749, 10.1016/j.cscm.2021.e00749. [DOI] [Google Scholar]
  • 45. Lawania K., Sarker P., and Biswas W., Global Warming Implications of the Use of by-Products and Recycled Materials in Western Australia′s Housing Sector, Materials. (2015) 8, no. 10, 6909–6925, 10.3390/ma8105347. [DOI] [Google Scholar]
  • 46. Saidi M., Safi B., Benmounah A., Megdoud N., and Radi F., Physico-Mechanical Properties and Thermal Behavior of Firebrick-Based Mortars in Superplasticizer Presence, Construction and Building Materials. (2016) 104, 311–321, 10.1016/j.conbuildmat.2015.12.026. [DOI] [Google Scholar]
  • 47. Bakr M. A., Singh B. K., Deifalla A. F., Pandey S., Hussain A., Ragab A. E., Alvi S. S., and Hasnain S. M., Assessment of the Mechanical and Durability Characteristics of Bio-Mineralized Bacillus subtilis Self-Healing Concrete Blended With Hydrated Lime and Brick Powder, Case Studies in Construction Materials. (2023) 19, e02672, 10.1016/j.cscm.2023.e02672. [DOI] [Google Scholar]
  • 48. Bouleghebar Y., Bentchikou M., Boukendakdji O., El-Hadj K., Debieb F., and Maisarah A., The Effect of Brick and Glass Powder on the Mechanical Properties and Porosity of Self-Compacting Mortar, Journal of Applied Engineering Sciences. (2023) 13, no. 1, 39–52, 10.2478/jaes-2023-0006. [DOI] [Google Scholar]
  • 49. Ruslan H. N., Muthusamy K., Yahaya F. M., Fauzi M. A., Ismail M. A., and Ali Z., Review on Performance of Self Compacting Concrete Containing Solid Waste and Bibliometric Properties: A Review, Journal of Building Engineering. (2024) 86, 108752, 10.1016/j.jobe.2024.108752. [DOI] [Google Scholar]
  • 50. Sahoo P., Dwivedi A., Tuppad S. M., and Gupta S., Sequestration and utilization of Carbon Dioxide to Improve Engineering Properties of Cement-Based Construction Materials With Recycled Brick Powder: A Pathway for Cleaner Construction, Construction and Building Materials. (2023) 395, 132268, 10.1016/j.conbuildmat.2023.132268. [DOI] [Google Scholar]
  • 51. Boukour S., Lafifi B., and Benmalek M. L., Some Properties of a Cementitious Mortar Containing Granulated Rubber Waste and Brick Fillers: An Experimental Study, Mathematical Modeling and Optimization, Slovak Journal of Civil Engineering. (2024) 32, no. 2, 27–37, 10.2478/sjce-2024-0011. [DOI] [Google Scholar]
  • 52. Schackow A., Stringari D., Senff L., Correia S., and Segadães A., Influence of Fired Clay Brick Waste Additions on the Durability of Mortars, Cement and Concrete Composites. (2015) 62, 82–89, 10.1016/j.cemconcomp.2015.04.019. [DOI] [Google Scholar]
  • 53. Sun Z., Liu F., Tong T., Qi C., and Yu Q., Hydration of Concrete Containing Hybrid Recycled Demolition Powders, Journal of Materials in Civil Engineering. (2017) 29, no. 7, 04017037, 10.1061/(ASCE)MT.1943-5533.0001842. [DOI] [Google Scholar]
  • 54. Zheng Y., Zhang W., Baca Lopez D. M., and Ahmad R., Scientometric Analysis and Systematic Review of Multi-Material Additive Manufacturing of Polymers, Polymers. (2021) 13, no. 12, 10.3390/polym13121957, 34204727. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 55. Boukour S. and Benmalek M., Performance Evaluation of a Resinous Cement Mortar Modified With Crushed Clay Brick and Tire Rubber Aggregate, Construction and Building Materials. (2016) 120, 473–481, 10.1016/j.conbuildmat.2016.05.119. [DOI] [Google Scholar]
  • 56. Chen G., Li S., Zhao Y., Xu Z., Luo X., and Gao J., Hydration and Microstructure Evolution of a Novel Low-Carbon Concrete Containing Recycled Clay Brick Powder and Ground Granulated Blast Furnace Slag, Construction and Building Materials. (2023) 386, 131596, 10.1016/j.conbuildmat.2023.131596. [DOI] [Google Scholar]
  • 57. Younis M., Amin M., and Tahwia A. M., Durability and Mechanical Characteristics of Sustainable Self-Curing Concrete Utilizing Crushed Ceramic and Brick Wastes, Case Studies in Construction Materials. (2022) 17, e01251, 10.1016/j.cscm.2022.e01251. [DOI] [Google Scholar]
  • 58. Zhang H., Ma J., Chen Z., and Wu B., Effect and Mechanism of Recycled Clay Brick Powder on Compressive Strength of Different Types of Concretes, Journal of Building Engineering. (2024) 94, 109983, 10.1016/j.jobe.2024.109983. [DOI] [Google Scholar]
  • 59. Kulovaná T., Vejmelková E., Pokorný J., Siddique J. A., Keppert M., Rovnaníková P., Ondráček M., Keršner Z., and Černý R., Engineering Properties of Composite Materials Containing Waste Ceramic Dust From Advanced Hollow Brick Production as a Partial Replacement of Portland Cement, Journal of Building Physics. (2016) 40, no. 1, 17–34, 10.1177/1744259115597228. [DOI] [Google Scholar]
  • 60. Kumar B. V., Ananthan H., and Balaji K., Experimental Studies on Cement Stabilized Masonry Blocks Prepared From Brick Powder, Fine Recycled Concrete Aggregate and Pozzolanic Materials, Journal of Building Engineering. (2017) 10, 80–88, 10.1016/j.jobe.2017.02.007. [DOI] [Google Scholar]
  • 61. Yao Y., Liu C., Liu H., Zhang W., and Hu T., Deterioration Mechanism Understanding of Recycled Powder Concrete Under Coupled Sulfate Attack and Freeze–Thaw Cycles, Construction and Building Materials. (2023) 388, 131718, 10.1016/j.conbuildmat.2023.131718. [DOI] [Google Scholar]
  • 62. Mohan M. and Singh B. K., Utilising Under-Burnt Waste Bricks From Kilns as Supplementary Cementitious Material, Advances in Cement Research. (2023) 35, 1–12, 10.1680/jadcr.22.00170. [DOI] [Google Scholar]
  • 63. Ortega J. M., Letelier V., Solas C., Moriconi G., Climent M. Á., and Sánchez I., Long-Term Effects of Waste Brick Powder Addition in the Microstructure and Service Properties of Mortars, Construction and Building Materials. (2018) 182, 691–702, 10.1016/j.conbuildmat.2018.06.161. [DOI] [Google Scholar]
  • 64. Ma Z., Tang Q., Wu H., Xu J., and Liang C., Mechanical Properties and Water Absorption of Cement Composites With Various Fineness and Contents of Waste Brick Powder From C&D Waste, Cement and Concrete Composites. (2020) 114, 103758, 10.1016/j.cemconcomp.2020.103758. [DOI] [Google Scholar]
  • 65. Mizaal A. M., Dawood E. T., and Fakhri R. S., Behavior of Green Reactive Powder Concrete Exposed to Aggressive Solutions, Innovative Infrastructure Solutions. (2024) 9, no. 10, 10.1007/s41062-024-01666-4. [DOI] [Google Scholar]
  • 66. Sharma U., Gupta N., and Saxena K. K., Comparative Study on the Effect of Industrial by-Products as a Replacement of Cement in Concrete, Materials Today: Proceedings. (2021) 44, 45–51, 10.1016/j.matpr.2020.06.211. [DOI] [Google Scholar]
  • 67. Chen G., Lin Z., Li L., He J., and Kwan A., Compressive Behavior of Concrete Incorporating Clay Brick Fines Added by Paste Replacement Method, Journal of Materials in Civil Engineering. (2021) 33, no. 7, 04021141, 10.1061/(ASCE)MT.1943-5533.0003752. [DOI] [Google Scholar]
  • 68. Grabois T., Cordeiro G., and Toledo Filho R., The Influence of Recycled Concrete and Clay Brick Particles on the Strength and Porosity of Cement-Based Pastes, Calcined Clays for Sustainable Concrete: Proceedings of the 2nd International Conference on Calcined Clays for Sustainable Concrete, 2018, Springer, 189–194, 10.1007/978-94-024-1207-9_30. [DOI] [Google Scholar]
  • 69. Suluguru A. K., Jayatheja M., Kar A., Guharay A., Surana S. R., and James N., Experimental Studies on the Microstructural, Physical and Chemical Characteristics of Building Derived Materials to Assess Their Suitability in Ground Improvement, Construction and Building Materials. (2017) 156, 921–932, 10.1016/j.conbuildmat.2017.09.058. [DOI] [Google Scholar]
  • 70. Zhang Y., Raza A., Umar M., Chen Y., and Yuan C., Study on Frost Resistance and Interface Bonding Performance Through the Integration of Recycled Brick Powder in Ultra-High-Performance Concrete for Structural Reinforcement, Materials. (2023) 16, no. 21, 10.3390/ma16216999, 37959596. [DOI] [PMC free article] [PubMed] [Google Scholar]

Associated Data

This section collects any data citations, data availability statements, or supplementary materials included in this article.

Data Availability Statement

The data that support the findings of this study are available on request from the corresponding author. The data are not publicly available due to privacy or ethical restrictions.


Articles from The Scientific World Journal are provided here courtesy of Wiley

RESOURCES