Skip to main content
PMC home page
Nature Portfolio logoLink to Nature Portfolio
. 2013 May 28;4:1922. doi: 10.1038/ncomms2944

Active and stable carbon nanotube/nanoparticle composite electrocatalyst for oxygen reduction

Hoon T Chung 1, Jong H Won 2, Piotr Zelenay 1,a
PMCID: PMC3674270  PMID: 23715281

Abstract

Nanostructured carbon-based materials, such as nitrogen-doped carbon nanotube arrays, Co3O4/nitrogen-doped graphene hybrids and carbon nanotube–graphene complexes have shown respectable oxygen reduction reaction activity in alkaline media. Although certainly promising, the performance of these materials does not yet warrant implementation in the energy conversion/storage devices utilizing basic electrolytes, for example, alkaline fuel cells, metal-air batteries and certain electrolysers. Here we demonstrate a new type of nitrogen-doped carbon nanotube/nanoparticle composite oxygen reduction reaction electrocatalyst obtained from iron acetate as an iron precursor and from cyanamide as a nitrogen and carbon nanotube precursor in a simple, scalable and single-step method. The composite has the highest oxygen reduction reaction activity in alkaline media of any non-precious metal catalysts. When used at a sufficiently high loading, this catalyst also outperforms the most active platinum-based catalysts.

Inline graphicCheap, efficient oxygen reduction reaction catalysts are vital for the development of fuel cells and lithium-air batteries. Here, the authors report the scalable synthesis of a nitrogen-doped carbon nanotube/nanoparticle hybrid material that outperforms several platinum-based catalysts.

Electrochemical reduction of oxygen in basic media is an important reaction for electrochemical devices directly related to efficient energy conversion and storage: fuel cells (operating with either liquid or polymer electrolytes), metal-air batteries and certain electrolysers (for example, chlor-alkali ones). Among those devices, a lithium (Li)-air secondary battery, potentially the most promising metal-air battery known, with a storage capacity approximately ten times that of the state-of-the-art Li-ion battery, can find application in hybrid electric vehicles and energy storage for intermittent sources of electricity, such as solar and wind1. In turn, the replacement of hydrogen-evolving cathode with an air cathode in chlor-alkali electrolysers is expected to reduce the energy consumption in the United States by close to 1% (thanks to lowering of the cathode-operating overpotential by more than 1.2 V (E° values of −0.828 V and 0.401 V, respectively))2. A successful large-scale implementation of these technologies depends, however, on the advent of active, stable and selective oxygen reduction reaction (ORR) catalysts, preferably free of precious metals.

To date, platinum (Pt) has shown the highest ORR activity in alkaline media. As a potential Pt replacement, silver (Ag) has been more thoroughly studied in comparison with other catalysts because of its relatively high activity, abundance and low cost. However, the ORR half-wave potential (E1/2) in rotating-disk electrode (RDE) polarization studies is by ca. 0.2 V lower for Ag than for Pt3,4. Carbon-based catalysts with promising ORR activity in alkaline electrolytes have also been demonstrated5,6. Although details of the ORR mechanism on such catalysts are yet to be fully understood, the adsorption of oxygen and formation of superoxide through a one-electron reduction (O2+e−←[O2(ads)]−) have generally been viewed as initial ORR steps5,6, with O2 adsorption proposed by Morcos and Yeager5 to be the rate-determining step. Thanks to preferred O2 adsorption on the exposed edge of graphene rather than the basal plane itself, the edges show high ORR activity comparable to that of Pt, while basal planes remain virtually ORR inactive5,6. N-doping into carbon nanotubes (CNTs) has been found to increase ORR activity in alkaline media by ca. 0.2 V at the E1/2 (refs. 7, 8). Doped nitrogen species increase the graphene edge presence by facilitating the formation of pentagonal defects in hexagonally arranged carbon atoms, causing disruption to the graphene structure, and by introducing irregularities to the curvature in the graphene stacking9, which eventually lead to enhanced ORR activity7. As these original findings were published7,8, various N-doped carbon catalysts, including CNTs10,11,12, graphene13,14, mesoporous carbon15,16 and particulate17, have been studied as a possible replacement for Pt. However, only vertically aligned N-containing CNTs (VA-NCNTs) have so far shown E1/2 values comparable to those measured with Pt/C catalysts8. VA-NCNTs are typically grown on a quartz substrate by chemical vapour deposition. A free-standing VA-NCNT film is obtained following a treatment with hydrofluoric acid that allows the catalyst film to be peeled off the substrate8. This expensive and tedious synthesis path precludes large-scale fabrication of the catalyst, rendering VA-NCNTs non-competitive with Pt-based catalysts.

Here we introduce a new type of N-doped nanostructured carbon-based catalyst, synthesized using iron acetate, Fe(CH3-COO)2, as an iron precursor and cyanamide, NCNH2, as a nitrogen precursor for iron-activated, N-doped catalyst, in which carbon phase is made up of a CNT/carbon nanoparticle (CNP) composite. This catalyst, labelled N-Fe-CNT/CNP, can be synthesized via a simple and scalable method using Fe, not only to induce ORR activity but also to catalyse the CNT growth. This composite catalyst shows the highest ORR activity in alkaline media of any nanostructured carbon-based catalysts8,10,13. When used at a sufficiently high loading, this catalyst also outperforms the most active Pt-based catalysts18,19,20,21.

Results

Synthesis

A solution of 3.5 g of cyanamide and 1.0 g of iron acetate in ethanol was first stirred for 3 h at 60 °C. One gram of oxidized carbon powder (Black Pearls 2000 pretreated in 70% nitric acid at 80 °C for 8 h) was then added to the solution and stirred at 60 °C overnight. Finally, the solvent was evaporated at 45 °C and remaining powder converted into the N-Fe-CNT/CNP composite catalyst by a heat treatment at 950 °C in nitrogen for 1 h. To remove a redundant phase, mainly unreacted metallic iron and iron compounds, the N-Fe-CNT/CNP composite catalyst was preleached in 0.5 M H2SO4 at 80 °C for 8 h. In the final step, the catalyst was heat-treated for a second time under the same conditions as during the first heat treatment. Although cyanamide has been primarily used as a source of graphitic-C3N4 (ref. 22), one of the important accomplishments of this work is the discovery that cyanamide can also serve as a CNT precursor.

Characterization

High-resolution transmission electron microscopy image of as-obtained N-Fe-CNT/CNP catalyst shows CNTs, ca. 20–30 nm in outer diameter and ca. 10 μm in length, homogeneously distributed in the CNP phase (Fig. 1a and Supplementary Fig. S1). The image of a CNT tip in Fig. 1b reveals iron encapsulated in several graphene nanoshells, the result of Fe-catalysed growth of CNTs. Iron particles are encapsulated in graphene nanoshells either at the tip or inside CNTs (Supplementary Fig. S2a–d). In some instances, iron can be encapsulated in the graphene nanoshells that are not part of the nanotubes (Supplementary Fig. S2e), which suggests that the encapsulation of iron into graphene nanoshells can be the first step of the CNT growth. Bamboo-like ‘joints’ (Fig. 1c and Supplementary Fig. S2f), also observed by others7,8, represent a typical morphological feature of N-doped CNTs synthesized in this work. The nitrogen content in the N-Fe-CNT/CNP composite catalyst, as measured by X-ray photoelectron spectroscopy (XPS), is 3.1 at% (Supplementary Table S1). XPS N 1s spectra can be deconvoluted into three peaks assignable to the pyridinic (398.3 eV), pyrrolic (400.0 eV) and graphitic (401.1 eV) nitrogen atoms (Supplementary Fig. S3). Although N-doping alone has been known to produce defects in the graphene stacking in CNTs7,9, the defects in the N-Fe-CNT/CNP catalyst can also be caused by CNPs obstructing linear CNT growth. The defects in graphene stacking in CNTs, resulting in the formation of O2 adsorption sites, are believed to be an important contributing factor to high activity of carbon-based catalysts5,6,7. The goal of generating high number of exposed graphene edges and, consequently, a high number of active ORR sites was achieved in this work via a single-step synthesis of N-doped CNT/CNP composite catalyst.

Figure 1. Micrographs of carbon nanotube/nanoparticle composite.

Figure 1

Open in a new tab

(a) High-resolution transmission electron microscopy of the N-Fe-CN/CNP composite catalyst. Scale bar, 200 nm. (b) Iron encapsulated in graphene nanoshells, Scale bar, 5 nm. (c) Typical bamboo-like defect in graphene stacking. Scale bar, 10 nm.

CNT-based composites have found numerous applications, for example, in Li-ion batteries and supercapacitors23,24, all requiring high nanotube dispersion—a big technical challenge because of CNTs’ tendency to self-agglomerate. Surface functionalization via a chemical treatment is therefore often needed, which results in additional processing steps and high cost. Contrary to the commonly used approaches, the synthesis of the N-Fe-CNT/CNP catalyst allows to achieve the desired CNT dispersion in a single step, without any additional treatments.

Electrochemical performance

ORR polarization data recorded with the N-Fe-CNT/CNP composite catalyst in 0.1 M NaOH at an RDE are shown in Fig. 2. The E1/2 value measured with the catalyst at a loading of 0.2 mg cm−2 is 0.87±0.01 V (Fig. 2a and Supplementary Fig. S4). For reference, the E1/2 value for a Pt/C catalyst (20 wt% Pt/C E-TEK) at a high precious metal loading of 60 μgPt cm−2 is 0.91 V (Fig. 2a), similar to the E1/2 value measured with a single crystal of Pt (111) (ca. 0.90 V) (ref. 3). Although the E1/2 value of 0.87 V is lower than that recorded with the Pt/C reference catalyst, the onset ORR potential measured with the N-Fe-CNT/CNP composite catalyst is by ca. 40 mV higher than for Pt/C (Fig. 2a, inset). On the basis of the onset potential values, the intrinsic ORR activity of the N-Fe-CNT/CNP composite appears to be higher than that of the Pt/C catalyst, with N-Fe-CNT/CNP suffering at higher overpotentials from a lower density of active ORR sites, reflected by a lower E1/2 value. In agreement with these observations, an increase in the N-Fe-CNT/CNP catalyst loading at the disk from 0.2 to 1.0 mg cm−2 yields a much-improved E1/2 value of 0.93 V, which exceeds the value measured with the Pt/C reference by ca. 20 mV (Fig. 2a).

Figure 2. The ORR performance of N-Fe-CNT/CNP composite and Pt/C catalysts.

Figure 2

Open in a new tab

Steady-state RDE polarization plots obtained using 20 mV potential step and 25 s potential hold time at every step; electrolyte 0.1 M NaOH; temperature 25 °C; rotation rate 900 r.p.m. ORR at the N-Fe-CNT/CNP catalyst measured in a negative-going scan; ORR at the Pt/C catalyst measured in a positive-going scan; insets zooming on low overpotential region. (a) ORR polarization plots before cycling durability test. (b) ORR polarization plots measured during cycling durability in O2-saturated 0.1 M NaOH (cycling in the potential range 0.6–1.0 V at 50 mV s−1; N-Fe-CNT/CNP loading 1.0 mg cm−2). (c) Tafel plots for the N-Fe-CNT/CNP catalyst before and after 5,000 cycles in an O2-saturated electrolyte (Tafel slope calculated by linear regression method in the intermediate range of current densities, 10−2–101 mA cm−2). (d) ORR polarization plots after 5,000 cycles in O2-saturated electrolyte.

The ORR Tafel slope measured with the N-Fe-CNT/CNP composite catalyst is ca. 80 mV per decade (Supplementary Fig. S5a). This value is similar to the one determined in this work for the Pt/C catalyst in the range of intermediate current densities, 0.2–5.0 mA cm−2 (Supplementary Fig. S5b).

A cycling durability test in O2-saturated solution in the potential range of 0.6–1.0 V at a scan rate of 50 mV s−1 not only shows no performance loss after 5,000 cycles but a positive shift in the E1/2 value (Fig. 2b). Although advanced surface characterization techniques may be needed to elucidate the mechanism of such an activity enhancement, a similar potential shift with cycling was already observed before with non-precious metal ORR catalysts at high current densities in proton conducting fuel cells25. In this work, the catalyst performance stabilizes after the first 5,000 cycles, with no further ORR activity change observed during the last 5,000 cycles (Fig. 2b). No changes upon cycling can be seen in the voltammograms recorded in the absence of oxygen, indicating that surface properties of the catalyst are maintained during cycling (Supplementary Fig. S6). During an analogous cycling test of the Pt/C reference catalyst the E1/2 value decreases by ca. 0.01 V down to 0.90 V (Supplementary Fig. S7). Chronoamperometric (constant potential) testing confirms very good stability of the N-Fe-CNT/CNP catalyst, including that at the highest current densities accessible in RDE experiments (Supplementary Fig. S8). On the basis of the data recorded at 0.4 V, the stability of a N-Fe-CNT/CNP performance is better than that of a reference Pt/C catalyst. It is possible that high selectivity for the four-electron reduction of O2 (see below) is an important contributing factor to high stability of the N-Fe-CNT/CNP catalyst.

The Tafel slope of ca. 80 mV per decade, initially measured with the N-Fe-CNT/CNP, remains virtually unchanged during cycling (Fig. 2c). Because of a gradual increase in the non-precious metal catalyst activity and a slight decrease in the activity of the Pt/C catalyst, the initial performance gap between the two catalysts increases to ca. 50 mV at E1/2 during cycling (Fig. 2d). The onset ORR potential measured with the N-Fe-CNT/CNP catalyst after 5,000 cycles increased to 1.16 V (Fig. 2d, inset).

The highest E1/2 and ORR onset potential to date were obtained in acid electrolytes with single-crystalline Pt3Ni catalyst (E1/2 ca. 0.92 V, ORR onset potential ca. 1.0 V)18 and nanoporous PtNi catalyst (E1/2 ca. 0.96 V, ORR onset potential ca. 1.05 V)20. Thus, the performance of the N-Fe-CNT/CNP composite catalyst developed in this work not only significantly exceeds that of any Pt-based catalyst in alkaline media but also at least matches performance of the most active Pt-alloy catalysts in acidic media (comparison made in reversible hydrogen electrode (RHE) potential scale). The volumetric activity of the N-Fe-CNT/CNP catalyst after 5,000 cycles, calculated from ikinetic in Fig. 2c, is 4.8±0.8 A cm−3 at 0.9 V. The latter value is ca. 37% higher than that obtained by Piana et al.26 (3.5±1.0 A cm−3) and 50% higher than the value measured by Meng et al.17 (3.2 A cm−3), but are still within the standard errors involved in the volumetric activity determination in these studies and the referenced research herein. Therefore, one should be careful making a performance superiority claim for the N-Fe-CNT/CNP catalyst based solely on the volumetric activity at 0.9 V. The true advantage of this catalyst is revealed, however, at even higher electrode potentials. Although other non-precious metal catalysts exhibit no detectable ORR activity at 1.0 V, a respectable volumetric activity of 0.32 A cm−3 is measured with N-Fe-CNT/CNP at that potential. Together with the very high onset potential value of 1.16 V, volumetric activity at 1.0 V attests to the unique performance of the N-Fe-CNT/CNP catalyst. When implemented in an alkaline fuel cell, the N-Fe-CNT/CNP catalyst is likely to allow cathode operation very close to 1.0 V.

The rotating ring-disk electrode (RRDE) results are shown in Supplementary Fig. S9 where the selectivity of N-Fe-CNT/CNP for four-electron reduction of oxygen is given in terms of hydrogen peroxide yield (% H2O2). The peroxide yield can be directly correlated with the average number of electrons transferred per O2 molecule, ne (ne=4−(% H2O2)/50%). In the potential range where hydrogen generation can be at all detected (E<0.80 V), the average number of electrons transferred decreases from 4.00 (no peroxide generation) to 3.92 at the lower polarization limit of 0.20 V (and for the low catalyst loading of 0.2 mg cm−2), still respectable by either non-precious metal or precious metal ORR electrocatalysis standards. Unlike other carbon-based oxygen reduction catalysts, for which the onset potentials for ORR and H2O2 generation coincide8, H2O2 generation at the N-Fe-CNT/CNP catalyst in this work starts at 0.79 V, ca. 0.29 V below the ORR onset potential, a behaviour similar to that observed with Pt catalysts3.

Discussion

We developed a new N-Fe-CNT/CNP composite electrocatalyst for ORR using a synthesis method that is expected to be readily scalable to larger volumes and applicable to the synthesis of other CNT-based composites. The catalyst exhibits higher ORR activity and better stability in the alkaline electrolyte than the state-of-the-art Pt/C catalysts. Its activity also exceeds that of other non-precious metal catalysts, including the recently published VA-NCNT catalyst8. The N-Fe-CNT/CNP catalyst promises to replace Pt-based catalysts in alkaline media and to have an important role in enhancing the performance of alkaline fuel cells, and possibly metal-air batteries and chlor-alkali electrolysers.

Methods

Electrochemical measurements

RDE and RRDE measurements were performed using a CHI Electrochemical Station (Model 750b) in a standard three-electrode cell. A 5.0-mm diameter glassy carbon disk (disk geometric area 0.196 cm2) and a 5.61-mm diameter glassy carbon disk with Pt ring (geometric area 0.247 cm2) were used in RDE and RRDE experiments, respectively. To avoid any potential contamination of the catalyst by Pt, all experiments involving N-Fe-CNT/CNP catalysts were carried out with a graphite rod as a counter electrode in a compartment separated from the main chamber by a glass frit. A reference electrode, also separated by a glass frit, was an Ag/AgCl electrode in 3.0 M NaCl. All potentials initially measured versus the Ag/AgCl electrode were converted to a RHE scale by adding 0.966 V (the potential of the Ag/AgCl reference measured against RHE). The catalyst ink was prepared by ultrasonically blending for 1 h 10 mg of the catalyst and 40 μl of 5 wt% Nafion suspension in alcohol (Solution Technology, Inc.), in 2.5 ml solution containing isopropanol and deionized water, 4:1 by volume. Before RDE experiments, 10 μl of the solution was applied to the 0.196-cm2 disk, resulting in a catalyst loading of 0.2 mg cm−2.

The reference Pt/C catalyst ink was prepared by ultrasonically blending for 5 min 1 mg of 20 wt% Pt/C (E-TEK) in 1 ml of deionized water. The reference catalyst loading was 60 μgPt cm−2. After drying the ink, 5 wt% Nafion suspension in alcohol was diluted with deionized water to attain 1:19 alcohol-to-water ratio by volume; 15 μl of that solution was then added on top of the Pt/C catalyst layer. The counter electrode in experiments involving the Pt/C reference catalyst was a platinized Pt wire. All RDE and RRDE testing was performed at a room temperature, 25±1 °C, in oxygen-saturated 0.1 M NaOH at a rotation rate of 900 r.p.m. The electrodes were activated by cyclic voltammetry in oxygen-saturated electrolyte at a scan rate of 50 mV s−1 and potential range of 0.0–1.2 V versus RHE. ORR polarization plots with non-precious metal catalyst were recorded under steady-state conditions, starting at the open cell potential (1.1–1.3 V, depending on the catalyst loading used) down to 0.0 V versus RHE, using a 0.02 V step and a potential hold time of 25 s. A 120-s potential hold at the open cell potential preceded every ORR polarization experiment. Because of the irreversible nature of the Pt surface hydroxide/oxide formation, polarization plots with the Pt/C catalyst were recorded using a positive-going scan, from 0.0 to 1.1 V versus RHE, under, otherwise, the same conditions as those used in testing of N-Fe-CNT/CNP composite catalysts. The ring collection efficiency in RRDE experiments was 0.36, as measured using a Fe(CN)64−/3− redox couple. The ring potential was set to 1.3 V versus RHE.

Volumetric activity was calculated from the product of mass activity (A g−1) and effective catalyst density (g cm−3). The mass-transport-corrected kinetic current density was obtained from Tafel plots. A relatively conservative value of the effective catalyst density of 0.4 g cm−3 was used to convert mass activity into volumetric activity. The catalyst effective density was determined based on X-ray tomography and scanning electron microscopy images. Virtually identical effective density values were published by Gasteiger et al.27 and Lefèvre et al.28

Physical characterization

XPS measurements were performed on a Kratos Axis Ultra spectrometer using monochromatic Al Kα line (1,486.6 eV) as an X-ray source. High-resolution transmission electron microscopy images were taken on a JEOL 2010 microscope operating at 200 kV.

Author contributions

H.T.C. performed the experiments. J.H.W. provided transmission electron microscopy characterization, and P.Z. and H.T.C. contributed jointly to data interpretation and manuscript preparation.

Additional information

How to cite this article: Chung, H. T. et al. Active and stable carbon nanotube/nanoparticle composite electrocatalyst for oxygen reduction. Nat. Commun. 4:1922 doi: 10.1038/ncomms2944 (2013).

Supplementary Material

Supplementary Information

Supplementary Figures S1-S9 and Supplementary Table S1

ncomms2944-s1.pdf (848.8KB, pdf)

Acknowledgments

Financial support of this study by the US Department of Energy (DOE) through Fuel Cell Technologies Office and by Los Alamos National Laboratory through Technology Maturation Fund and Laboratory Directed Research and Development (LDRD) is greatly appreciated. We thank Drs Yu Seung Kim, Christina Johnston and Gang Wu for discussions.

References

  1. Girishkumar G., McCloskey B., Luntz A. C., Swanson S. & Wilcke W. Lithium - air battery: promise and challenges. J. Phys. Chem. Lett. 1, 2193–2203 (2010). [Google Scholar]
  2. Moussallem I., Jorissen J., Kunz U., Pinnow S. & Turek T. Chlor-alkali electrolysis with oxygen depolarized cathodes: history, present status and future prospects. J. Appl. Electrochem. 38, 1177–1194 (2008). [Google Scholar]
  3. Schmidt T. J., Stamenkovic V., Arenz M., Markovic N. M. & Ross P. N. Oxygen electrocatalysis in alkaline electrolyte: Pt(hkl), Au(hkl) and the effect of Pd-modification. Electrochim. Acta 47, 3765–3776 (2002). [Google Scholar]
  4. Blizanac B. B., Ross P. N. & Markovic N. M. Oxygen reduction on silver low-index single-crystal surfaces in alkaline solution: rotating ring diskAg(hkl) studies. J. Phys. Chem. B 110, 4735–4741 (2006). [DOI] [PubMed] [Google Scholar]
  5. Morcos I. & Yeager E. Kinetic studies of oxygen-peroxide couple on pyrolytic graphite. Electrochim. Acta 15, 953–975 (1970). [Google Scholar]
  6. Qu D. Y. Investigation of oxygen reduction on activated carbon electrodes in alkaline solution. Carbon 45, 1296–1301 (2007). [Google Scholar]
  7. Maldonado S. & Stevenson K. J. Influence of nitrogen doping on oxygen reduction electrocatalysis at carbon nanofiber electrodes. J. Phys. Chem. B 109, 4707–4716 (2005). [DOI] [PubMed] [Google Scholar]
  8. Gong K. P., Du F., Xia Z. H., Durstock M. & Dai L. M. Nitrogen-doped carbon nanotube arrays with high electrocatalytic activity for oxygen reduction. Science. 323, 760–764 (2009). [DOI] [PubMed] [Google Scholar]
  9. Sjostrom H., Stafstrom S., Boman M. & Sundgren J. E. Superhard and elastic carbon nitride thin-films having fullerene-like microstructure. Phys. Rev. Lett. 75, 1336–1339 (1995). [DOI] [PubMed] [Google Scholar]
  10. Yanguang L. et al. An oxygen reduction elctrocatalyst based on carbon nanotube-graphene complexes. Nat. Nanotechnol. 7, 394–400 (2012). [DOI] [PubMed] [Google Scholar]
  11. Kim S. O., Lee D. H., Lee W. J., Lee W. J. & Kim Y. H. Theory, synthesis, and oxygen reduction catalysis of Fe-porphyrin-like carbon nanotube. Phys. Rev. Lett. 106, 175502 (2011). [DOI] [PubMed] [Google Scholar]
  12. Shanmugam S. & Osaka T. Efficient electrocatalytic oxygen reduction over metal free-nitrogen doped carbon nanocapsules. Chem. Commun. 47, 4463–4465 (2011). [DOI] [PubMed] [Google Scholar]
  13. Liang Y. Y. et al. Co3O4 nanocrystals on graphene as a synergistic catalyst for oxygen reduction reaction. Nat. Mater. 10, 780–786 (2011). [DOI] [PubMed] [Google Scholar]
  14. Qu L. T., Liu Y., Baek J. B. & Dai L. M. Nitrogen-doped graphene as efficient metal-free electrocatalyst for oxygen reduction in fuel cells. ACS Nano 4, 1321–1326 (2010). [DOI] [PubMed] [Google Scholar]
  15. Liu R. L., Wu D. Q., Feng X. L. & Mullen K. Nitrogen-doped ordered mesoporous graphitic arrays with high electrocatalytic activity for oxygen reduction. Angew. Chem. Int. Engl. 49, 2565–2569 (2010). [DOI] [PubMed] [Google Scholar]
  16. Yang W., Fellinger T. P. & Antonietti M. Efficient metal-free oxygen reduction in alkaline medium on high-surface-area mesoporous nitrogen-doped carbons made from ionic liquids and nucleobases. J. Am. Chem. Soc. 133, 206–209 (2011). [DOI] [PubMed] [Google Scholar]
  17. Meng H., Jaouen F., Proietti E., Lefevre M. & Dodelet J. P. pH-effect on oxygen reduction activity of Fe-based electro-catalysts. Electrochem. Commun. 11, 1986–1989 (2009). [Google Scholar]
  18. Stamenkovic V. R. et al. Improved oxygen reduction activity on Pt3Ni(111) via increased surface site availability. Science 315, 493–497 (2007). [DOI] [PubMed] [Google Scholar]
  19. Zhang J., Sasaki K., Sutter E. & Adzic R. R. Stabilization of platinum oxygen-reduction electrocatalysts using gold clusters. Science 315, 220–222 (2007). [DOI] [PubMed] [Google Scholar]
  20. Snyder J., Fujita T., Chen M. W. & Erlebacher J. Oxygen reduction in nanoporous metal-ionic liquid composite electrocatalysts. Nat. Mater. 9, 904–907 (2010). [DOI] [PubMed] [Google Scholar]
  21. Greeley J. et al. Alloys of platinum and early transition metals as oxygen reduction electrocatalysts. Nat. Chem. 1, 552–556 (2009). [DOI] [PubMed] [Google Scholar]
  22. Groenewolt M. & Antonietti M. Synthesis of g-C3N4 nanoparticles in mesoporous silica host matrices. Adv. Mater. 17, 1789–1792 (2005). [Google Scholar]
  23. Lota G., Fic K. & Frackowiak E. Carbon nanotubes and their composites in electrochemical applications. Energy Environmen. Sci. 4, 1592–1605 (2011). [Google Scholar]
  24. Su D. S. & Schlogl R. Nanostructured carbon and carbon nanocomposites for electrochemical energy storage applications. ChemSusChem 3, 136–168 (2010). [DOI] [PubMed] [Google Scholar]
  25. Wu G., More K. L., Johnston C. M. & Zelenay P. High-performance electrocatalysts for oxygen reduction derived from polyaniline, iron, and cobalt. Science 332, 443–447 (2011). [DOI] [PubMed] [Google Scholar]
  26. Piana M., Catanorchi S. & Gasteiger H. A. Kinetics of non-platinum group metal catalysts for the oxygen reduction reaction in alkaline medium. ECS Trans. 16, 2045–2055 (2008). [Google Scholar]
  27. Gasteiger H. A., Kocha S. S., Sompalli B. & Wagner F. T. Activity benchmarks and requirements for Pt, Pt-alloy, and non-Pt oxygen reduction catalysts for PEMFCs. Appl. Catal. B 56, 9–35 (2005). [Google Scholar]
  28. Lefevre M., Proietti E., Jaouen F. & Dodelet J. P. Iron-based catalysts with improved oxygen reduction activity in polymer electrolyte fuel cells. Science 324, 71–74 (2009). [DOI] [PubMed] [Google Scholar]

Associated Data

This section collects any data citations, data availability statements, or supplementary materials included in this article.

Supplementary Materials

Supplementary Information

Supplementary Figures S1-S9 and Supplementary Table S1

ncomms2944-s1.pdf (848.8KB, pdf)

Articles from Nature Communications are provided here courtesy of Nature Publishing Group

RESOURCES