Skip to main content
PMC home page
Scientific Reports logoLink to Scientific Reports
. 2014 Apr 3;4:4580. doi: 10.1038/srep04580

Tandem-structured, hot electron based photovoltaic cell with double Schottky barriers

Young Keun Lee 1,2, Hyosun Lee 1,2, Jeong Young Park 1,2,a
PMCID: PMC3974133  PMID: 24694838

Abstract

We demonstrate a tandem-structured, hot electron based photovoltaic cell with double Schottky barriers. The tandem-structured, hot electron based photovoltaic cell is composed of two metal/semiconductor interfaces. Two types of tandem cells were fabricated using TiO2/Au/Si and TiO2/Au/TiO2, and photocurrent enhancement was detected. The double Schottky barriers lead to an additional pathway for harvesting hot electrons, which is enhanced through multiple reflections between the two barriers with different energy ranges. In addition, light absorption is improved by the band-to-band excitation of both semiconductors with different band gaps. Short-circuit current and energy conversion efficiency of the tandem-structured TiO2/Au/Si increased by 86% and 70%, respectively, compared with Au/Si metal/semiconductor nanodiodes, showing an overall solar energy conversion efficiency of 5.3%.

There has been substantial research focused on converting solar energy into electricity since the development of the pn-junction solar cell. Recently, various strategies have been proposed to enhance the maximum possible efficiency of a solar cell with a band gap of 1.1 eV, 30% of which is called the single-junction Shockley–Queisser limit1. Semonin et al. demonstrated photocurrent enhancement assisted by multiple exciton generation on semiconductor quantum dots, which led to a quantum efficiency exceeding 100% in the quantum dot solar cell2. The plasmonic solar cell could be a viable thin solar cell capable of efficiently absorbing broad light wavelengths. As the thickness of the photoactive materials increases, light harvesting is improved, whereas carrier recombination easily occurs, leading to a trade-off between light absorption and carrier collection. For excellent optical absorption without considerable loss of charge carriers in a thin solar cell, the surface plasmon based solar cell has been studied. Dang et al. observed improved broadband light harvesting when using multiple core–shell structured oxide/metal/oxide plasmonic nanoparticles in a dye-sensitized solar cell (DSSC), resulting in an increased photovoltaic cell efficiency (PCE) from 8.3% to 10.8%3. Atwater et al. and Reineck et al. have suggested possible mechanisms for enhancement of solar cell performance based on plasmonic materials4,5. There are possibilities for implementation of metal nanoparticles in solar cells that have local near-field enhancement, a high scattering cross section, and an actual light harvesting element that induces charge separation. In addition, tunable surface geometry that increases the surface area for higher dye loading and light harvesting and reduced charge recombination in DSSC were reported by Ko et al. who fabricated a nanoforest composed of high-density, long-branched, multi-generation hierarchical ZnO nanowires6. However, an intrinsic challenge in solar cells is limited light absorption on the photoactive materials. A stacking structure generally consisting of a low-bandgap material and a high-bandgap material—called a tandem cell—was introduced to maximize absorption across the solar spectrum7. Recently, application of tandem cells has expanded from an inorganic solar cell to an organic solar cell that includes a polymer solar cell to overcome low carrier mobility (i.e., a limiting factor for power conversion efficiency)8,9,10. Dou et al. designed a tandem polymer solar cell that consists of a low-bandgap conjugated polymer spectrally matched with the front cell, showing an increased PCE (8.62%), compared with a single-layer polymer solar cell (6%)11.

The initial effort to develop a solar energy conversion device can be traced back to the metal/semiconductor (MS) junction with a thin metal film. The MS diode has two mechanisms for generation of excited electrons as photocurrent: band-to-band excitation on the semiconductor and internal photoemission from the thin metal film (i.e., hot electrons). It is known that hot electrons, which have high kinetic energy (1–3 eV), can be generated in metals when external energy is deposited on the surface, such as in the absorption of light12. Energetic charge carriers excited during photon illumination have been detected on thin metal/semiconductor contacts or metal/insulator/metal tunneling junctions13,14,15. It was reported that surface modification of a thin metal film, such as a connected island structure or deposited nanowires, enhanced the yield of energetic charge carrier generation. Knight et al. showed the possibility for photodetection using energetic charge carriers injected over a Schottky energy barrier at the interface between a gold nanostructure (the antenna) and n-type silicon16. The gold nanostructure was coupled with incident photons and exhibited resonant plasmons that excited energetic charge carriers and resulted in a detectable photocurrent17,18. Wang et al. observed excitation of hot carriers via plasmon absorption on Au/Al2O3/Au junctions, suggesting that a simple planar metal/insulator/metal diode can play a role as a light harvesting device based on hot electron extraction19. Among approaches to increase the PCE in MS solar cells based on internal photoemission and band-to-band excitation, parallel energy harvesting with tandem cells could be ideal.

In this work, we demonstrate solar energy conversion using a tandem-structured, hot electron based photovoltaic cell with double Schottky barriers for multiple reflections of hot electrons and two semiconductor layers for enhancement of band-to-band excitation, as illustrated in Fig. 1a. We show a tandem-structured solar cell composed of multilayers with different absorption characteristics, which is a promising strategy to increase energy conversion efficiency.

Figure 1.

Figure 1

Open in a new tab

(a) Scheme of a tandem-structured TiO2/Au/Si diode where the TiO2 layer is stacked as the second semiconductor on a thin gold film to form double Schottky barriers. (b) A cross-sectional image of the TiO2-deposited Au film on silicon, showing an approximately 50 nm thick layer of TiO2 and a 10 nm thick layer of Au on the silicon. The Au layer plays a role as a common electrode to the two semiconductors and as an optical absorption layer for internal photoemission. (c) The energy band diagram for internal photoemission enhanced by the double Schottky barriers and band-to-band excitation on the two semiconductors. The red line represents internal photoemission and generation of hot electrons on the metal and the blue line represents separation of the electron/hole pairs on two semiconductors by band-to-band excitation.

Results and discussion

In the tandem-structured, hot electron based photovoltaic cell, the double Schottky barriers were built on the two interfaces of a thin gold film that makes contact with the TiO2 and silicon. Fig. 1b shows a cross section of TiO2 deposited on a Au film on silicon, where the Au layer plays a role as a common electrode that has Schottky contacts to two semiconductors. The corrugated Au layer (periodic pattern) refers to the cross-section view of the Au island structures. The Au layer is also an optical absorption layer for internal photoemission. The transport process of electrons on a metal/semiconductor contact is illustrated in the energy diagram in Fig. 1c. The proposed tandem-structured, hot electron based photovoltaic cell harvests the photo-excited charge carriers via two channels: band-to-band excitation on two semiconductors and internal photoemission (or hot carrier generation) based on absorption on the metal layer and transport across the double Schottky barriers.

Two pathways for internal photoemission and band-to-band excitations are shown as the red and blue lines in Fig. 1c, respectively. As the incident photon energy (hν) is greater than the band gap (Eg) of the semiconductors, electron–hole pairs are produced in the semiconductors while hot electrons (via the internal photoemission process) are generated by absorption of incident photon energy on the thin gold film. In the case where the Schottky energy barrier (ESB) < hν < Eg, the predominant route to excite energetic electrons is internal photoemission in the metal film because the band-to-band excitation of the semiconductors can be negligible in the photon energy range13,20. The total photocurrent (A) measured on the tandem structure can be obtained by collecting the photocurrent from both subcells, as shown in Fig. 1c. Christine et al. developed models of the effect of the Schottky barrier on internal photoemission from the metal film into the semiconductor21. They presented the enhanced emission probability of hot carriers in the case of double Schottky barriers as a result of multiple hot carrier reflections within the metal film and emission over two Schottky barriers, compared with a single Schottky barrier. In our study, we combined these two mechanisms using a tandem-structured Schottky diode with double Schottky barriers. We found that the tandem-structured Au/Si diode capped with a TiO2 layer as the second semiconductor exhibited improved solar energy conversion efficiency because of an increased incident photon to current conversion efficiency (IPCE) in the visible light region.

The effect of the double Schottky barriers on photocurrent was observed on the TiO2-deposited Au/Si diodes. Fig. 2a,b shows current–voltage curves of Au/Si and TiO2/Au/Si, respectively, revealing that the photocurrent increased when illuminated by a tungsten–halogen lamp and that the rectifying property of the diodes was well preserved after deposition of TiO2 on the Au/Si. The photocurrent density measured under illumination by a halogen–tungsten lamp dramatically increased from 2.4 to 5.0 mA/cm2 after deposition of TiO2 on the Au/Si (Fig. 2c). While the Au/Si cell shows a rectangular shape, as expected, the TiO2/Au/Si tandem cell exhibited transient behavior (2% increase in current for 5 seconds). Such transient behavior was recently found in TiO2-based heterojunctions and was attributed to dielectric effects and oxide instability22.

Figure 2.

Figure 2

Open in a new tab

Current–voltage curves measured on (a) the Au/Si diode and (b) the tandem-structured TiO2/Au/Si diode, showing an enhanced light response under illumination by a halogen–tungsten lamp (9 mW/cm2). The current–voltage curves without light illumination reveal that the rectifying behaviors of the diodes were well maintained. (c) Plot of a short-circuit photocurrent measured on the Au/Si diode and the tandem-structured TiO2/Au/Si diode. (d) Energy band diagram for the effect of double Schottky barriers leading to multiple reflections of hot electrons, resulting in enhanced internal photoemission.

The energy band diagram of the TiO2-deposited Au/Si diodes could be different from that of Au/Si, as proposed by Fig. 2d, because the second Schottky barrier was built at the interface between the TiO2 and the thin gold layer. Fig. 2d shows the routes for internal photoemission from the thin gold film to both semiconductors through the double Schottky barriers. First, hot electrons with energy higher than each Schottky energy barrier can overcome both Schottky barriers toward the semiconductors (red lines). In addition, the emission probability of the hot electrons can be enhanced through multiple reflections (blue line) until the excess energy of the hot electrons is reduced to the lower Schottky energy barrier. If the photons with energy hν are absorbed uniformly and not emitted, the hot electrons are assumed to reflect elastically and diffusely from the metal/semiconductor interfaces. The number of trips taken by the hot electrons via multiple reflections within the double Schottky barriers can be given by

graphic file with name srep04580-m1.jpg

where n is the total number of trips the hot electrons take via multiple reflections, L is the mean free path of the hot electrons, t is the thickness of the thin metal film, hν is the photon energy, and ΦB is the Schottky barrier21. In the case of a single Schottky barrier, the value of nmax decreases by half because there is only one route for internal photoemission. At the same time, improved efficiency of the band-to-band excitation is expected by absorption of photon energy on the two semiconductors with different band gaps. In the tandem-structured Au/Si, the anti-reflecting effect can be negligible because the refractive index of the thin gold film is smaller than that of the TiO2 film in the range of visible light incident on the tandem-structured Au/Si23.

The photocurrent density was measured as a function of TiO2 layer thickness (Fig. 3a). The thickness of the TiO2 was controlled by changing the concentration of the sol–gel solution, as shown in Fig. 3b–d. The photocurrent density increased as the TiO2 layer thickness increased up to 44 nm thick; however, the photocurrent density decreased when the TiO2 layers were thicker than 44 nm. An appropriate TiO2 thickness is required to guarantee band bending at the interface between the TiO2 and the Au. In the case of the 22 nm thick TiO2 layer, the TiO2 layer could be too thin for stable band bending at the interface between the TiO2 and the Au. On the other hand, when the TiO2 thickness exceeds 44 nm, absorption of incident light on the TiO2 increases, leading to a decrease of incident light to the Au and Si. Therefore, there exists an optimal thickness (44 nm) of TiO2 to maximize the photocurrent in the tandem-structured TiO2/Au/Si diode.

Figure 3.

Figure 3

Open in a new tab

(a) Plot of photocurrent density as a function of TiO2 layer thickness under light illumination. Cross-sectional SEM images of (b) a 44 nm thick TiO2 layer, (c) a 63 nm thick TiO2 layer, and (d) a 81 nm thick TiO2 layer.

Fig. 4a shows solar cell performance characteristics of the tandem-structured Au/Si. The short-circuit current density (JSC) and open-circuit voltage (VOC) were measured on the Au/Si (black line) and the tandem-structured TiO2/Au/Si (red line) diodes under illumination of air mass 1.5 global (AM 1.5 G). After TiO2 deposition, the JSC increased from 22 to 41 mA/cm2, showing that the tandem-structured metal/semiconductor diode has an improved capability to harvest photon energy by utilizing the double Schottky barriers. The VOC increased from 0.33 V to 0.40 V. These VOC values are rather low, comparable to a diazole-based cell24. A possible explanation for the increased open-circuit voltage after the adsorption of TiO2 on the Au/Si could be associated with a change in the Schottky barrier height. The change in the Schottky barrier of the TiO2-adsorbed Au/Si, compared with the Au/Si, was obtained by fitting I–V curves to the thermionic emission equation (Fig. S1). The Schottky barrier height was modified from 0.816 eV to 0.842 eV. In this approach, the Schottky barrier height, 0.842 eV, is representative of the overall value of the combined double Schottky barriers. For an ideal Schottky contact, the Schottky barrier height is expected to be ΦB = Φm − χ, where Φm is the work function of the metal and χ is the electron affinity of the semiconductor (n-type)20. In the Schottky diode, the VOC is linearly proportional to the Schottky barrier height25. In the double Schottky barrier, the overall Schottky barrier height can be affected by the formation of the second Schottky barrier because electrons overcome the potential barrier and travel into the semiconductors from the metal film in the thermionic emission process. Therefore, if a higher Schottky barrier is formed at the interface of the TiO2 and the Au film rather than at the interface of the silicon and the Au film (0.816 eV), the overall Schottky barrier height can become higher (0.842 eV). In our previous work, the experimental Schottky barrier height of ~1.1 eV for Au/TiO2 was reported, which is acceptable compared to the literature value26,27. As a result, it is probable that the newly formed higher Schottky barrier at the interface of the Au/TiO2 could increase the overall Schottky barrier height, resulting in the increased VOC. Fig. 4b shows the IPCE obtained by measuring photocurrent as a function of wavelength. The IPCE plot of the tandem-structured TiO2/Au/Si is greater than that of the Au/Si across the entire range of wavelengths, whereas the Au/TiO2 didn't exhibit any photon response in the visible light spectrum. The improved ability for current generation of the tandem structure can originate from multiple reflections between the double Schottky barriers and enhanced band-to-band excitation. In addition, it is possible that the increase in the IPCE plot could be attributed to improved penetration of the incident light through the TiO2/Au, enhancing light absorption on the silicon substrate. The absorbance spectra were measured using a UV-Vis spectrometer on the TiO2-deposited Au film on quartz (Fig. S2). The deposition of the TiO2 film on the Au film improved light penetration to the silicon substrate in the visible range, while the TiO2 film on quartz absorbed nearly no incident light.

Figure 4.

Figure 4

Open in a new tab

(a) Current–voltage characteristic for solar cell performance under AM 1.5 G. In the tandem-structured TiO2/Au/Si, the short–circuit current and the open–circuit voltage increased, compared with those of Au/Si, whereas the fill factor was smaller than that of Au/Si because the resistance factor increased. (b) Incident photon to current conversion efficiency as a function of wavelength measured on the Au/Si diode (red line) and the tandem-structured TiO2/Au/Si diode (green line), showing that the tandem-structured TiO2/Au/Si exhibited an enhanced efficiency, compared with that of Au/Si, across the entire range of wavelengths. The black line represents the IPCE of Au/TiO2, revealing no generation of photocurrent under visible light.

The current density of the Si/Au/TiO2 tandem cell is 41 mA/cm2 under AM 1.5 G with a light intensity of 100 mW/cm2, which results in a photovoltaic cell efficiency of 5.3% in the hot electron tandem cell. Compared with that of the Au/Si structure (3.1%), the tandem cell exhibited an increase in efficiency of ~70%. The VOC and JSC under AM 1.5 G improved on the tandem-structured TiO2/Au/Si; however, the fill factor (FF) decreased because the resistance factors of the cell increased (Fig. S3)17. The dielectric effect of the TiO2/Au/Si tandem cell can be at least partly associated with enhancement of the short-circuit current. However, as the change in current is not significant (i.e., less than 2% for 5 seconds), the dielectric effect or instability of the oxide might be minor effects.

To verify the concept of a tandem-structured hot electron solar cell, we constructed a TiO2/Au/TiO2 tandem cell and compared the photocurrent of the tandem cell with that of a Au/TiO2 single cell. Fig. 5a,b shows the scheme and scanning electron microscopy (SEM) image of the TiO2/Au/TiO2 tandem cell, respectively. The top TiO2 layer (50 nm thick) was prepared and coated on a Au/TiO2 single cell using the sol–gel method. Fig. S4 shows the representative I–V curves of a Au/TiO2 single cell and the TiO2/Au/TiO2 tandem cell. After surface modification of the thin Au film and deposition of TiO2, the rectifying property was well preserved. Fig. 5c shows photocurrent measured on Au/TiO2, Au islands/TiO2, and TiO2/Au islands/TiO2. The higher photocurrent was obtained on the Au islands/TiO2, compared with the thin film Au/TiO2, as a result of surface plasmons18. A thin Au film was modified to a connected island structure to enhance hot electron generation via surface plasmons. The photocurrent of the TiO2/Au islands/TiO2 tandem solar cell was higher than that of the Au islands/TiO2 by a factor of three, which is beyond the range of the photocurrent caused by an antireflection layer. As shown in Fig. 5d, the peak in IPCE of the TiO2/Au/TiO2 originating from hot electron flow is broader and higher than that of the Au/TiO2, which could be associated with enhanced hot electron flows because of the double barriers. We note that there is a slight contribution to photocurrent by thermionic emission in the range of 400–520 nm (IPCE < 0.5%); the exact contribution depends on the defect level of the TiO217,18. In addition, since the metallic layer is surrounded by semiconductor layers with different dielectric constant, the potential difference in the tandem cell can give additional complexities28.

Figure 5.

Figure 5

Open in a new tab

(a) Schematic and (b) SEM image of the TiO2/Au/TiO2 tandem cell showing the edge of the top TiO2 layer on the Au/TiO2 diode. (c) Plot of photocurrent density under light illumination measured on the thin film Au/TiO2, connected Au island/TiO2 diode, and TiO2/Au/TiO2 tandem cell using a halogen–tungsten lamp (9 mW/cm2). (d) IPCE as a function of wavelength measured on the connected Au island/TiO2 diode (black line) and the TiO2/connected Au/TiO2 tandem cell (red line).

This study suggests that the enhancement of hot electron injection by the use of double Schottky barriers is a general phenomenon. The improvement of the solar cell performance suggests that the concept of double Schottky barriers has significant potential as a novel strategy for light harvesting with high energy conversion efficiency.

In summary, hot electron-based tandem cells of TiO2/Au/Si and TiO2/Au/TiO2 were fabricated for enhanced light harvesting. In the tandem-structured cell, the energy band diagram was modified to form double Schottky barriers at both interfaces between the Au film and the semiconductors. The double Schottky barriers can play a role as a reflector for an enhanced hot electron's trip and as an additional route for internal photoemission. In addition, light absorption is improved by the band-to-band excitation of both semiconductors with different band gaps. The effect of the double Schottky barriers was exhibited through enhanced performance of the solar cell. After modification from Au/Si to the tandem-structured TiO2/Au/Si, the JSC and solar cell efficiency were enhanced by 86% and 70%, respectively. The photocurrent of TiO2/Au/TiO2 exhibited a threefold increase, compared with that of the Au/TiO2 single cell. A tandem hot electron photovoltaic device with double Schottky barriers may pave the way for novel methods for light harvesting.

Methods

For fabrication of a tandem-structured Schottky diode, vertically oriented Au/Si Schottky diodes were fabricated on an n-type (100) silicon wafer. The first step consists of depositing a 200 nm thick film of SiO2 on a Si wafer via plasma-enhanced chemical vapor deposition through an aluminum shadow mask. A 50 nm thick film of aluminum and a 150 nm thick film of Au are then deposited through a second mask using electron beam evaporation, which constitutes the nanodiode's two ohmic electrodes. Finally, a thin gold film (10 ± 2 nm thick) is deposited through a third mask. The short-circuit photocurrent was measured with a sourcemeter (Keithley Instrumentation, 2400) under illumination from a halogen–tungsten lamp. Only the active area of the diode was illuminated by the light source. We used a metal mask to block the other areas of the device. In addition, we measured the photocurrent using a laser light source (green, 532 nm ± 10, 5 mW) with a beam size of 0.5 mm. We found that when the laser source illuminated the active area, photocurrent was generated. Therefore, we can rule out the contribution of photocurrent from the bulk Si that is outside of the active region.

For electrical characterization of the diodes, current–voltage measurements were performed by sweeping the voltage between two electrodes and measuring the resulting current. By fitting the current–voltage curves of the diodes to the thermionic emission equation, the Schottky barrier heights, ideality factors, and series resistances for the nanodiodes were obtained20,27.

For preparation of a TiO2 film, the sol–gel process was utilized. First, 0.5 ml of titanium tetraisopropoxide (Ti(OC3H7)4), or TTIP, was added to 9.5 ml of ethanol, which was then mixed with 5 μl of nitric acid29,30. The TTIP and ethanol were used for the precursor and solvent, respectively. The nitric acid assists the TiO2 sols to form a gel and prevents precipitation of the TiO2 particles. The TiO2 was deposited using the spin coating method. Optical properties of the films were characterized using a UV-Vis spectrophotometer (U–4001, Hitachi). The spectral range capability of the instrument is 300–1100 nm. For measurement of the films, the thin gold layer and the sol–gel TiO2 were deposited on a 1/16″ thick quartz window, and the instrument was used in standard setup mode. A bare quartz window was used as a reference to remove the absorption of the quartz.

Author Contributions

Y.K.L. and J.Y.P. planned the projects and designed the experiments; Y.K.L. and H.L. fabricated the devices; all the authors interpreted and discussed the results and commented on the manuscript.

Supplementary Material

Supplementary Information

Supplementary Information

srep04580-s1.doc (406KB, doc)

Acknowledgments

The work was supported by the Institute for Basic Science (IBS) [CA1401-04], Republic of Korea.

References

  1. Shockley W. & Queisser H. J. Detailed balance limit of efficiency of p-n junction solar cells. J. Appl. Phys. 32, 510–519 (1961). [Google Scholar]
  2. Semonin O. E. et al. Peak external photocurrent quantum efficiency exceeding 100% via MEG in a quantum dot solar cell. Science 334, 1530–1533 (2011). [DOI] [PubMed] [Google Scholar]
  3. Dang X. N. et al. Tunable localized surface plasmon-enabled broadband light-harvesting enhancement for high-efficiency panchromatic dye-sensitized solar cells. Nano Lett. 13, 637–642 (2013). [DOI] [PMC free article] [PubMed] [Google Scholar]
  4. Atwater H. A. & Polman A. Plasmonics for improved photovoltaic devices. Nature Mater. 9, 205–213 (2010). [DOI] [PubMed] [Google Scholar]
  5. Reineck P. et al. A solid-state plasmonic solar cell via metal nanoparticle self-assembly. Adv. Mater. 24, 4750–4755 (2012). [DOI] [PubMed] [Google Scholar]
  6. Ko S. H. et al. Nanoforest of hydrothermally grown hierarchical ZnO nanowires for a high efficiency dye-sensitized solar sell. Nano Lett. 11, 666–671 (2011). [DOI] [PubMed] [Google Scholar]
  7. Devos A. Detailed balance limit of the efficiency of tandem solar-cells. J. Phys. D Appl. Phys. 13, 839–846 (1980). [Google Scholar]
  8. Nattestad A. et al. Highly efficient photocathodes for dye-sensitized tandem solar cells. Nature Mater. 9, 31–35 (2010). [DOI] [PubMed] [Google Scholar]
  9. Kim J. Y. et al. Efficient tandem polymer solar cells fabricated by all-solution processing. Science 317, 222–225 (2007). [DOI] [PubMed] [Google Scholar]
  10. Sista S., Hong Z. R., Park M. H., Xu Z. & Yang Y. High-efficiency polymer tandem solar cells with three-terminal structure. Adv. Mater. 22, E77 (2010). [DOI] [PubMed] [Google Scholar]
  11. Dou L. T. et al. Tandem polymer solar cells featuring a spectrally matched low-bandgap polymer. Nature Photon. 6, 180–185 (2012). [Google Scholar]
  12. McFarland E. W. & Tang J. A photovoltaic device structure based on internal electron emission. Nature 421, 616–618 (2003). [DOI] [PubMed] [Google Scholar]
  13. Somorjai G. A., Frei H. & Park J. Y. Advancing the frontiers in nanocatalysis, biointerfaces, and renewable energy conversion by innovations of surface techniques. J. Am. Chem. Soc. 131, 16589–16605 (2009). [DOI] [PubMed] [Google Scholar]
  14. de Arquer F. P. G., Mihi A., Kufer D. & Konstantatos G. Photoelectric energy conversion of plasmon-generated hot carriers in metal-insulator-semiconductor structures. ACS Nano 7, 3581–3588 (2013). [DOI] [PubMed] [Google Scholar]
  15. Kovacs D. A., Winter J., Meyer S., Wucher A. & Diesing D. Photo and particle induced transport of excited carriers in thin film tunnel junctions. Phys. Rev. B 76, 235408 (2007). [Google Scholar]
  16. Knight M. W., Sobhani H., Nordlander P. & Halas N. J. Photodetection with active optical antennas. Science 332, 702–704 (2011). [DOI] [PubMed] [Google Scholar]
  17. Lee Y. K., Lee J., Lee H., Lee J. Y. & Park J. Y. Probing polarization modes of Ag nanowires with hot electron detection on Au/TiO2 nanodiodes. Appl. Phys. Lett. 102, 123112 (2013). [Google Scholar]
  18. Lee Y. K. et al. Surface plasmon-driven hot electron flow probed with metal-semiconductor nanodiodes. Nano Lett. 11, 4251–4255 (2011). [DOI] [PubMed] [Google Scholar]
  19. Wang F. M. & Melosh N. A. Plasmonic energy collection through hot carrier extraction. Nano Lett. 11, 5426–5430 (2011). [DOI] [PubMed] [Google Scholar]
  20. Sze S. M. & Ng K. K. Physics of Semiconductor Devices (WILEY-INTERSCIENCE, 2006). [Google Scholar]
  21. Scales C. & Berini P. Thin-film schottky barrier photodetector models. IEEE J. Quant. Electron. 46, 633–643 (2010). [Google Scholar]
  22. Stella K., Kovacs D. A., Diesing D., Brezna W. & Smoliner J. Charge transport through thin amorphous titanium and tantalum oxide layers. J. Electrochem. Soc. 158, P65–P74 (2011). [Google Scholar]
  23. Wang X. F., Chen K. P., Zhao M. & Nolte D. D. Refractive index and dielectric constant evolution of ultra-thin gold from clusters to films. Opt. Express 18, 24859–24867 (2010). [DOI] [PubMed] [Google Scholar]
  24. You J. et al. A polymer tandem solar cell with 10.6% power conversion efficiency. Nature Commun. 4, 1446 (2013). [DOI] [PMC free article] [PubMed] [Google Scholar]
  25. Luther J. M. et al. Schottky solar cells based on colloidal nanocrystal films. Nano Lett. 8, 3488–3492 (2008). [DOI] [PubMed] [Google Scholar]
  26. Lee Y. K., Park J. & Park J. Y. The effect of dye molecules and surface plasmons in photon–induced hot electron flows detected on Au/TiO2 nanodiodes. J. Phys. Chem. C 116, 18591–18596 (2012). [Google Scholar]
  27. Park J. Y., Lee H., Renzas J. R., Zhang Y. W. & Somorjai G. A. Probing hot electron flow generated on Pt nanoparticles with Au/TiO2 Schottky diodes during catalytic CO oxidation. Nano Lett. 8, 2388–2392 (2008). [DOI] [PubMed] [Google Scholar]
  28. Hornauer H., Vancea J., Reiss G. & Hoffmann H. Thickness dependence of the work function in double-layer metallic-films. Z. Phys. B Condens. Mat. 77, 399–407 (1989). [Google Scholar]
  29. Van T. N., Lee Y. K., Lee J. & Park J. Y. Tuning hydrophobicity of TiO2 Layers with silanization and self-assembled nanopatterning. Langmuir 29, 3054–3060 (2013). [DOI] [PubMed] [Google Scholar]
  30. Qadir K., Kim S. H., Kim S. M., Ha H. & Park J. Y. Support effect of arc plasma deposited Pt Nanoparticles/TiO2 substrate on catalytic activity of CO oxidation. J. Phys. Chem. C 116, 24054–24059 (2012). [Google Scholar]

Associated Data

This section collects any data citations, data availability statements, or supplementary materials included in this article.

Supplementary Materials

Supplementary Information

Supplementary Information

srep04580-s1.doc (406KB, doc)

Articles from Scientific Reports are provided here courtesy of Nature Publishing Group

RESOURCES