Skip to main content
Scientific Reports logoLink to Scientific Reports
. 2014 Nov 24;4:7165. doi: 10.1038/srep07165

New strategy to promote conversion efficiency using high-index nanostructures in thin-film solar cells

DongLin Wang 1, Gang Su 1,a
PMCID: PMC4241512  PMID: 25418477

Abstract

Nano-scaled metallic or dielectric structures may provide various ways to trap light into thin-film solar cells for improving the conversion efficiency. In most schemes, the textured active layers are involved into light trapping structures that can provide perfect optical benefits but also bring undesirable degradation of electrical performance. Here we propose a novel approach to design high-performance thin-film solar cells. In our strategy, a flat active layer is adopted for avoiding electrical degradation, and an optimization algorithm is applied to seek for an optimized light trapping structure for the best optical benefit. As an example, we show that the efficiency of a flat a-Si:H thin-film solar cell can be promoted close to the certified highest value. It is also pointed out that, by choosing appropriate dielectric materials with high refractive index (>3) and high transmissivity in wavelength region of 350 nm–800 nm, the conversion efficiency of solar cells can be further enhanced.


Solar radiation is a clean, stable and abundant energy source. The photovoltaic (PV) device with high efficiency and low cost is essential for extensive utilization of solar energy. Today, the PV market is dominated by wafer based crystalline Si (c-Si) solar cell, which has the efficiency as high as 22% in commercial modules1,2. However, the high cost of existing PV modules is a key stumbling block for widespread use of PV technology. Alternative thin film solar cell may provide some viable ways to realize win-win situation between cost and efficiency3,4. A thinner active layer has a number of advantages, such as decreasing the material usage for a lower cost, reducing the carrier collection length and bulk recombination for a higher efficiency5,6,7. However, a key premise behind above benefits is to maintain a high light absorption in the thin active region8. Traditional method for enhancing the light absorption in thick solar cells is to employ a macroscopic texture on the front surface, which redirects the light propagation to increase the light path in the active layer9. Nonetheless, this macroscopic structure is not suitable for thin film solar cells where the thickness may be only few hundred nanometers. Exploration on an effective light trapping structure appropriate for a thin absorber is therefore urgent and crucial in developing the thin film solar cells with high efficiency and low cost.

Thin film hydrogenated amorphous silicon (a-Si:H) solar cells are potential candidates for the global terawatt range deployment, as it is based on nontoxic, abundant and stable materials10,11. Random pyramidal texture has demonstrated a remarkable light trapping capability to achieve the certified highest conversion efficiency (10.1%) in a single junction a-Si:H solar cell2,12. Recently, plasmonic based nanostructures that can couple the light into the thin a-Si:H layer13,14,15,16,17,18,19,20 have received significant attention. In particular, nanodome or nanocone plasmonic back reflectors employed a-Si:H thin film solar cells have achieved the highest short circuit current (17.5 mA/cm2)21, fill factor (~69%)22 and conversion efficiency (~10%)23,24 for periodic light trapping structures. Mie resonator in dielectric nanostructures25 and whispering gallery resonator in spherical nanoshells26 have also revealed an effective light trapping in a-Si:H thin film solar cells. However, these schemes involve the structured active layers that may bring localized defects in materials. Those defects may increase the carrier recombination and degrade the electrical properties of the solar cells. As a result, the performance of solar cell is a tradeoff between the optical benefits and the electrical degradations23,24,27,28. It is better that the ultimate light trapping structures only lead to the enhancement of optical absorption but avoid a direct involvement of the active layers.

Recently, some innovative light trapping structures that separate from the active layer have been proposed, including plasmonic based metallic nanostructures29,30,31, patterned transparent conductive oxides32 and dielectric nanosphere arrays33,34. In these schemes, the flat active layers were employed with the best quality of materials. However, the maximal enhancement of the efficiency from light trapping is only 11% in a thin a-Si:H solar cell34. The optical performance of those light trapping structures still needs to be optimized and improved. In addition, the full field optical and electrical computer simulations can also provide useful information to design the high performance light trapping structures in thin film solar cells18,19,28,34,35,36, which, however, rely on one's physical intuition to predefine the geometry of the light trapping structure, and are hard to handle the geometrical variation in seeking for the optimized results37. To remedy this, in this work, an effective geometrical optimization algorithm is combined into a full field solar cell simulation process to search for the optimized light trapping structures. To show the power of this method, as an example, we adopt a flat a-Si:H active layer to avoid local defects so that the best electrical performance of the solar cell can be achieved. High refractive indexed scatterers are also considered as light trapping structures that are periodically arranged on the front surface of the flat solar cell and only provide optical benefits. The method proposed in this paper has great potential to better improve the performance of thin film solar cells.

Results

Tunable light trapping structures based on high-indexed dielectric

For a-Si:H thin-film solar cells, the ultrathin active layers (<300 nm) are necessary for improving the collection efficiency of carriers and reducing the light-induced degradation38,39,40. In a flat solar cell, such a thin absorber can only support several discrete electromagnetic modes. Under a poor light absorption, the effective light trapping can be achieved by coupling the incident light into those guided modes. Usually, there are three ways to implement it, including plasmonic resonator, dielectric resonator and grating diffraction, but which way is the best for light trapping in ultrathin solar cells is still not be established1. Recently, high refractive indexed dielectric nanostructures have received much attention, because it can excite optical resonances for trapping the light like metallic nanostructures but has a parasitic absorption lower than metal25,41,42. The resonant modes are also sensitive to the shape and the size of the dielectric. It is possible that a proper design can promote those modes to provide the best light trapping in thin film solar cells.

Here we take an example to show the implementation of such a design. As shown in Fig. 1, the periodically arranged GaP scatterers (with high index>3) are placed on the top surface of a flat a-Si:H thin-film solar cell for trapping the light into an active layer. The geometry projection method (GPM)43,44 is employed to optimize the shape of the dielectric scatterers in seeking for the optimal light trapping structures. This method is more superior to the traditional topology optimization, because it can generate the geometry with smooth edge which is convenient for practical fabrication. The details about the calculation can be found in Method and Supplementary Note 1.

Figure 1. Model of an a-Si:H thin film solar cell and schematic depiction of geometry projection method (GPM) used for optimizing the cross section of the dielectric scatterer.

Figure 1

By employing GPM, the cross section shape of the scatterer can be controlled by adjusting the height of the control points. The optimization of the shape can be converted into searching for proper heights of the control points.

For the thin film a-Si:H solar cell, most of light can be absorbed in a single light path when the light is with a short wavelength (λ<500 nm). In this case, the main loss of light is caused by reflection at the front surface of the solar cell. Here the shape of the cross section of the dielectric scatterer is optimized to reduce the reflection in the short wavelength region (350 nm–500 nm). As shown in Figure 2a and 2c, the quatrefoil patterned scatterer with height H = 120 nm and patch L = 300 nm demonstrates a perfect antireflection in the short wavelength region. Especially, the total reflection at wavelength λ = 458 nm can be smaller than 3%. An obvious enhancement of light absorption in the active layer was obtained from λ = 400 nm to λ = 550 nm as the result of a remarkable antireflection. However, when λ<400 nm the optical loss appears in the active layer due to a large parasitic absorption in GaP scatterer.

Figure 2. Structures of the designed dielectric scatterers and the corresponding light absorption efficiency as function of wavelength in a-Si:H thin-film solar cells.

Figure 2

The optimal dielectric structures for light trapping in the short wavelength region (a) and in the long wavelength region (b). (c) Calculated light absorption efficiency in total solar cell and a-Si:H layer for above two dielectric scatterers. Light absorption efficiency in the flat solar cell without scatterers is shown as a reference.

In the long wavelength region (λ>600 nm), the light absorption is weak in the active layer. The unabsorbed light will be reflected back by the bottom Ag layer, which leads to an insignificant enhancement of the light absorption by the antireflection. In this situation, it is an effective way to couple the incident light into the guided modes in the thin flat active layer to improve the light absorption. Through our optimization calculation, the dielectric scatterer with a different geometrical structure and a perfect light trapping capacity in the long wavelength region (600 nm–800 nm) was obtained. In Figure 2b and 2c, the four-pointed star shaped scatterer with height H = 180 nm and patch L = 600 nm can improve excellently the light absorption from λ = 600 nm to λ = 800 nm. In particular, the absorption in the active layer at wavelength λ = 688 nm can exceed 80%. In the short wavelength region, however, the parasitic absorption in the scatterer reduces the light absorption in the active layer.

Figure 3 shows the profiles of the normalized intensity of light field inside the solar cells with the above-designed two scatterers at the wavelength 458 nm and 688 nm where the best performance appears. At a short wavelength λ = 458 nm, a proper shaped and sized dielectric excites the optical resonance that can be coupled into the substrate layers to increase the forward scattering and reduce the back reflection (Fig. 3a). This phenomenon is similar to the antireflection coating based on the excitation of a Mie resonance25. At a long wavelength λ = 688 nm, the excited optical resonance can couple the incident light into the waveguide modes, which can increase greatly the light path in the active layer and implement the excellent light trapping (Fig. 3b).

Figure 3. Normalized electric and magnetic field intensity profiles inside a-Si:H thin-film solar cells.

Figure 3

The intensity profiles are calculated at the incident light wavelength 458 nm for the solar cell with a short wavelength scatterer (a) and the wavelength 688 nm for the solar cell with a long wavelength scatterer (b). The top profiles are perpendicular to the y direction and at the maximal intensity of fields in scatterers. The bottom profiles are selected at the middle of the unit cell, where the intensity of electric fields is shown in the yx plane and the intensity of magnetic fields is in the yz plane.

Flat and stepped scatterers for the optimal light trapping

To implement a light trapping structure in the whole wavelength region (350 nm–800 nm), it is necessary to combine the above two kinds of dielectric scatterers in one unit cell. What we expect is that one scatterer can reduce the reflection in the short wavelength region, and another can couple the light into the guided modes in the long wavelength region. To achieve this goal, we design a flat scatterer with an eclectic height H = 160 nm and patch L = 600 nm (Fig. 4a). As is expected, this flat scatterer exhibits the combined capability for improving the total absorption of the solar cell in the whole wavelength region (Fig. 4b). Unfortunately, it is observed that the increase of the size of the scatterer brings more parasitic absorption that reduces the light absorption in the active layer when λ<450 nm. More detail about the parasitic absorption in the solar cell can be found in Supplementary Note 2.

Figure 4. Structure of the designed flat dielectric scatterer and the corresponding light absorption as function of wavelength in the a-Si:H thin-film solar cell.

Figure 4

(a) The flat dielectric scatterer with height H = 160 nm and patch L = 600 nm has the combined capacity to trap the light in both short and long wavelength regions. (b) The calculated light absorption in total solar cell as well as in the a-Si:H layer for the designed flat dielectric scatterer. Four absorption peaks generated by grating appear at wavelength 715 nm, 720 nm, 751 nm and 798 nm. Light absorption in the flat solar cell without scatterers is taken as a reference. (c) Light absorptions in the a-Si:H layer with the flat scatterer for various heights.

In this flat scatter, the height (H) of the dielectric is an important factor to control the light absorption in the active layer. As shown in Fig. 4c, the light absorption peaks generated by dielectric resonators will offset when the height is changed. The lower scatterer is favorable to reduce the reflection, while the higher scatterer is beneficial for coupling the light into the guided modes. Moreover, there are four light absorption peaks that are insensitive to the height of the scatterer, which are caused by the periodical grating that can also couple the light into the guided modes to enhance the light absorption.

In fact, the eclectic height of the flat scatterer somewhat refrains the dielectric resonator from exhibiting the optimal performance of light trapping. To remedy this shortcoming, we propose another strategy that employs the stepped scatterer which contains both a lower (H = 120 nm) and a higher (H = 180 nm) dielectric structures (Fig. 5 a). It turns out that the perfect antireflection is caused by the optical resonance in the lower dielectric, giving rise to the total absorption in the solar cell exceeding 90% in a broad wavelength region (350 nm–550 nm) (Fig. 5 b). Meanwhile, the optical resonance in the higher dielectric is beneficial for effectively coupling the light into the guided modes. Therefore, this stepped scatterer has more advantages to trap the light into the active layer than the flat one.

Figure 5. Structure of the designed stepped dielectric scatterer and the corresponding light absorption as function of wavelength in the a-Si:H thin-film solar cell.

Figure 5

(a) The stepped dielectric scatterer is combined by a lower scatterer with height H = 120 nm and a higher scatterer with height H = 180 nm. (b) The calculated light absorption in the total solar cell as well as in the a-Si:H layer for the designed stepped dielectric scatterer. Two absorption peaks generated by grating appear at wavelength 720 nm and 751 nm. The corresponding light absorption in the flat solar cell without scatterers is taken as a reference.

Grating diffraction for light trapping

The periodically arranged scatterers also have grating effect that can redirect the propagation direction of light through the optical interference and diffraction. In this case, a remarkable enhancement of the light absorption can be achieved when the parallel propagation constant (β) of the redirected light and the guided modes can match each other. Figure 6 presents the band structures of waveguide modes as a function of parallel propagation constant for the flat a-Si:H layer. The guided modes with increasing order (m = 0, 1, 2, 3, 4) extend from the light cone of a-Si:H to the light cone of indium doped tin oxide (ITO). The bottom Ag layer can excite the surface plasma resonance (SPR) in aluminum doped zinc oxide (AZO) layer, which only has a slight influence on higher order bands of the a-Si:H layer due to the separation by AZO layer. The scatterer in this work can be considered as a two-dimensional square lattice grating with period L = 600 nm. Figure 6a represents several matched channels (blue dots) in k space provided by the grating10. The matching condition for the propagation constant can be described by

graphic file with name srep07165-m1.jpg

For a thin film a-Si:H solar cell, it is more significant to couple the light into the guided modes in the long wavelength region (600 nm–800 nm). Under the normal incidence, in this region there are six matching conditions indicated by vertical lines in Fig. 6b. (Under the oblique incidence, the match channels of the grating will drift if the incident angle changes). The intersections of the matched lines and the bands of modes suggest that the couplings between the incident light and the guided modes are tenable (Fig. 6). Light couplings caused by grating at the hollow intersections are weaker than those caused by dielectric resonators, so the enhancements of light absorption from grating are merged into those from dielectric resonators. The solid intersections represent the strong grating coupling that leads to a remarkable enhancement for the light absorption in the active layer. Four distinguishable absorption peaks appear in the absorption spectra of the solar cell with the flat scatterer (Fig. 4), while there are two peaks in the absorption spectra of the solar cell with the stepped scatterer (Fig. 5). By contrast, the linewidth of the enhanced absorption spectra from grating is much narrower than that from the dielectric resonator, because the guided modes in the thin active layer and the match channels provided by grating are both discrete.

Figure 6. Coupling channels in k space and band structures of the guided modes as function of the parallel propagation constant (β) in the a-Si:H thin-film solar cell.

Figure 6

(a) Grating provides several discrete channels (blue dots) that can couple the light into the guided modes in the active layer. The channels intersected by circles represent the eligible match conditions that are available for trapping the light with the wavelength from 600 nm to 800 nm. (b) The calculated band structures of the guided modes for the transverse electric (TE) and the transverse magnetic (TM) polarization in the a-Si:H solar cell. Black and blue solid lines are light cone for air, SiO2, ITO, a-Si:H and the band for the surface plasma resonance (SPR) excited by Ag layer, respectively. The vertical lines correspond to the k values of the eligible coupling channels in (a).

Electrical performance of the designed solar cells

The designed scatterers in this work can enhance the light absorption in the active layer in a broad wavelength region. Here, to investigate the electrical performance of the designed solar cells (Fig. 7), the external quantum efficiency (EQE) and the current-voltage curve are calculated. The results show that the EQEs of solar cells are similar to but smaller than the light absorption efficiencies in active layers due to the influence of carrier recombination. The flat or stepped scatterer can enhance the EQE of the thin-film solar cell in a broad wavelength region for λ>450 nm (Fig. 7a). In the short wavelength region of λ<450 nm, the main loss is the photo-induced carriers in scatterers and ITO (see Supplementary Note 2). However, the total enhancement of EQE is still remarkable, which can be directly translated into the increases of the short circuit current density (Jsc). As shown in Fig. 7b, the calculated Jsc of the flat solar cell without scatterers is about 11.41 (mA/cm2), which is consistent with the previous experiment21. By introducing the above flat or stepped scatterer, Jsc can be improved to 13.08 (mA/cm2) and 13.76 (mA/cm2), respectively. Although there is no obvious increase of the open circuit voltage (Voc) and the fill factor (FF), the conversion efficiency of the solar cell has a prominent enhancement. The efficiency of 8.1% for a bare solar cell can be improved to 9.37% for the solar cell with a flat scatterer and 9.89% with the stepped scatterer. In particular, the efficiency of the a-Si:H solar cell with the stepped scatterer is close to the world record (10.1%), but it cannot be broken due to the loss of the trapped light energy from the large parasitic absorption in the scatterer in the short wavelength region of λ<450 nm.

Figure 7. External quantum efficiency (EQE) and current-voltage curve for a-Si:H thin-film solar cells with and without scatterers.

Figure 7

(a) EQEs for solar cells with and without sactterers. (b) current-voltage curve and main performance parameter for solar cells with and without scatterers. The short circuit current density (Jsc), the open circuit voltage (Voc), the fill factor (FF) and the efficiency for solar cells are embedded in (b).

Figure 8 shows the angle dependences for the solar cells with the above designed light trapping structures. The enhancements of light absorption indicate that the absorption decreases at λ<450 nm that becomes more serious under a large incident angle. Fortunately, the increase of absorption can be sustained for almost all incident angles when λ>450 nm (Figs. 8a and 8b). In particular, more than twice of the light absorption in the active layers for about all oblique angles can be gained from λ = 680 nm to λ = 750 nm. By collecting the net enhancements of absorption in the solar cells, the improvement of Jsc and the efficiency can also be achieved in a wide angle region (Figs. 8c and 8d). But, a remarkable enhancement of Jsc induced by the flat and stepped scatterers can only be sustained when the incident angle is within 10°, which decreases rapidly when the oblique angle is greater than this angle. On the contrary, Jsc for the bare solar cell increases as the oblique angle increases from 0° to Brewster's angle (around 50°). Taking the efficiency of the bare solar cell as a reference, the enhancement of efficiency of the solar cell with the flat scatterer can reach 15.7% under the normal incident, and that with the stepped scatterer can be up to 22.1%. However, those prominent enhancements can only be maintained within a small angle region (<10°), which decreases rapidly beyond this region till Brewster's angle. Nevertheless, the enhancement of efficiency more than 10% can still be maintained when the incident angle is less than 20°. The reasons behind the above phenomenon are complex, but one of them comes from the increase of parasitic absorptions of the scatterers as the incident angle becomes larger in the short wavelength region (Figs. 8a and 8b). Such parasitic absorption wastes a lot of light energy trapped in the thin-film solar cell.

Figure 8. Under an oblique incidence, the enhancement of optical and electrical performances for a-Si:H thin-film solar cells with the above designed scatterers.

Figure 8

Light absorption enhancement in the active layers for the solar cell with (a) flat and (b) stepped scatterers. The values of the enhancements below zero imply the decrease of light absorption, and on the contrary, the values exceeding zero indicate the increase of light absorption. Here the enhancements are truncated by 1 to show clearly the region that has more than twice of the light absorption. (c) Jsc of the solar cells with and without scatterers under various incident angles. (d) The efficiency enhancements of the solar cells with the above designed scatterers as function of the incident angle. The efficiency of bare solar cell is considered as a reference.

Discussion

In summary, we proposed a novel approach to improve effectively the conversion efficiency of the thin-film solar cells by optimizing the light trapping structures, implemented by combining the GMP method and the full field optical and electrical simulations. The designed light trapping structure is separated from the flat active layer to ensure both the optical benefits and the best electrical performance of the solar cell. The geometrical shape optimization of high-indexed scatterers is used for seeking for the best capture of light in the thin-film solar cell. To implement our strategy, we take the a-Si:H thin-film solar cell as an example, where a flat and a stepped scatterers are designed to provide the excellent light trapping in the cells. With the designed two scatterers, we calculate the maximal enhancement of the conversion efficiency for the a-Si:H thin-film solar cells can be up to 15.7% and 22.1%, respectively, which are better than the previous values31,34. Our calculated maximal efficiency (9.89%) of the designed a-Si:H thin-film solar cells is very close to the reported highest value (10.1%). Here we would like to emphasize that our study manifests that there may be two ways to improve further the conversion sufficiency of the thin-film solar cells: the first is to choose the transparent (350 nm–800 nm) and high indexed (>3) materials as the scatterers with optimized shape structures to reduce the parasitic absorptions in the short wavelength region, and the second is to combine with other light trapping mechanism (such as SPR) to increase the light absorption in the long wavelength region. The strategy proposed in this work is also applicable to the solar cell systems with other materials, which would have great potential to design the thin-film solar cells with high performance.

Methods

Unit cell of the model

The basic model of the flat a-Si:H thin-film solar cell is adopted according to an actual structure in a previous work21. As shown in Figure 1, the single junction a-Si:H solar cell consists of 100 nm thick Ag back reflector on SiO2 substrate, 80 nm thick AZO layer, 280 nm thick active layer (from top to bottom, 10 nm thick p layer, 250 nm i layer and 20 nm n layer) and 80 nm thick ITO layer. Light trapping is based on the high indexed GaP scatterer with height H and pitch L. The scatterer is placed on the surface of ITO to keep the best electrical performance of the solar cell. D2 symmetry is imposed by to reduce the computational requirements.

Optical and electrical simulations

The simulation method to implement the optical and electrical performance is based on the previous work20,37. All simulations are carried out by using the finite element method (FEM) software package37. The light field distribution in a solar cell can be obtained by solving Maxwell's equations. We assume that the light absorbed by the active layer is all used for exciting carriers. Then, we can use the light field information in the active layer to describe the generation rate of the carriers20. Finally, the electrical performance of the solar cell can be gained by calculating the transport equations of carriers and Poisson's equation. The calculation details can be found in Supplementary Note 1.

Optimization of geometrical shape structure

In this work, GPM is employed to optimize the geometrical shape of the dielectric scatterer. GPM distributes several control points on the optimization region, and fits a three-dimensional (3D) surface by the heights of those control points, and finally defines the geometrical shape by the intersection curve between a level plane and the 3D surface. By employing the GPM, the shape optimization problem can be transformed into the issue that searches for the optimal heights of the control points. This simplified optimization problem can be readily handled by any optimization algorithm.

In this work, the optimization region is chosen as the cross-section of the unit cell which contains the dielectric scatterer. The shape of the dielectric is defined by the intersection curve between the 3D surface and a level plane. Here, such an intersection curve is approximated by a polygon which has 50~80 sides for accurate calculations. The data information of those sides is converted into the FEM script to realize the connection between FEM and GPM. The shape of the scatterer is changed by adjusting the heights of the control points. The Nelder–Mead algorithm45 is applied to seek for the optimal heights of those control points in combination with the optical and electrical calculations.

Author Contributions

D.W. and G.S. conceived the project. D.W. designed and executed the simulations. All authors prepared and contributed to the editing of the manuscript.

Supplementary Material

Supplementary Information

New strategy to promote conversion efficiency using high-index nanostructures in thin-film solar cells

srep07165-s1.pdf (267.1KB, pdf)

Acknowledgments

The authors are benefitted from useful discussions with Q.B. Yan, Z.G. Zhu and Q.R. Zheng. This work is supported in part by the MOST of China (Grant No. 2012CB932900 and No. 2013CB933401), the Strategic Priority Research Program of the Chinese Academy of Sciences (Grant No. XDB07010100), and the China Postdoctoral Science Foundation (2014M550805).

References

  1. Brongersma M. L., Cui Y. & Fan S. Light management for photovoltaics using high-index nanostructures. Nat Mater. 13, 451–460 (2014). [DOI] [PubMed] [Google Scholar]
  2. Green M. A., Emery K., Hishikawa Y., Warta W. & Dunlop E. D. Solar cell efficiency tables (version 43). Prog. Photovoltaics Res. Appl. 22, 1–9 (2014). [Google Scholar]
  3. Green M. A. Third Generation Photovoltaics: Advanced Solar Energy Conversion (Springer, 2005). [Google Scholar]
  4. Sangmoo J., Shuang W. & Yi C. Nanoscale photon management in silicon solar cells. J. Vac. Sci. Technol. A 30, 060801 (2012). [Google Scholar]
  5. Shah A. V. et al. Thin-film solar cell technology. Progr. Photovolt. Res. Appl. 12, 113–142 (2004). [Google Scholar]
  6. Sze S. M. & Ng K. K. Physics of Semiconductor Devices. (John Wiley & Sons, New York 2007). [Google Scholar]
  7. Ferry V. E. et al. Light trapping in ultrathin plasmonic solar cells. Opt. Express 18, A237–A245 (2010). [DOI] [PubMed] [Google Scholar]
  8. Nelson J. Physics of Solar Cell (Imperial College Press: London, 2008). [Google Scholar]
  9. Zhao J., Wang A., Green M. A. & Ferrazza F. 19.8% efficient “honeycomb” textured multicrystalline and 24.4% monocrystalline silicon solar cells. Appl. Phys. Lett. 73, 1991–1993 (1998). [Google Scholar]
  10. Schropp R. E. I. & Zeman M. Amorphous and Microcrystalline Silicon Solar Cells: Modeling, Materials, and Device Technology. (Kluwer Academic Publishers: Boston, MA, 1998). [Google Scholar]
  11. Shah A., Torres P., Tscharner R., Wyrsch N. & Keppner H. Photovoltaic technology: the case for thin-film solar cells. Science 285, 692–698 (1999). [DOI] [PubMed] [Google Scholar]
  12. Benagli S. et al. High-Efficiency Amorphous Silicon Devices on LPCVD-ZnO TCO Prepared in Industrial KAI-M Reactor. 24th Eur. Photovolt. Solar Energy Conf. 3BO.9.3, 2293–2298 (2009). [Google Scholar]
  13. Atwater H. A., Polman A. Plasmonics for improved photovoltaic devices. Nat. Mater. 9, 205–213 (2010). [DOI] [PubMed] [Google Scholar]
  14. Ferry V. E., Sweatlock L. A., Pacifici D. & Atwater H. A. Plasmonic nanostructure design for efficient light coupling into solar cells. Nano Lett. 8, 4391–4397 (2008). [DOI] [PubMed] [Google Scholar]
  15. Ferry V. E., Munday J. N. & Atwater H. A. Design considerations for plasmonic photovoltaics. Adv. Mater. 22, 4795–4808 (2010). [DOI] [PubMed] [Google Scholar]
  16. Ferry V. E. et al. Optimized Spatial Correlations for Broadband Light Trapping Nanopatterns in High Efficiency Ultrathin Film a-Si:H Solar Cells. Nano Lett. 11, 4239–4245 (2011). [DOI] [PubMed] [Google Scholar]
  17. Hairen T., Rudi S., Arno H. M. S. & Miro Z. Plasmonic Light Trapping in Thin-film Silicon Solar Cells with Improved Self-Assembled Silver Nanoparticles. Nano Lett. 12, 4070–4076 (2012). [DOI] [PubMed] [Google Scholar]
  18. Deceglie M. G., Ferry V. E., Alivisatos A. P. & Atwater H. A. Design of nanostructured solar cells using coupled optical and electrical modeling. Nano Lett. 12, 2894–900 (2012). [DOI] [PubMed] [Google Scholar]
  19. Ferry V. E., Polman A. & Atwater H. A. Modeling light trapping in nanostructured solar cells. ACS Nano 5, 10055–10064 (2011). [DOI] [PubMed] [Google Scholar]
  20. Naughton M. J. et al. Efficient nanocoax-based solar cells. Phys. Status Solid.-Rapid Res. Lett. 4, 181–183 (2010). [Google Scholar]
  21. Zhu J., Hsu C. M., Yu Z., Fan S. & Cui Y. Nanodome Solar Cells with Efficient Light Management and Self-Cleaning. Nano Lett. 10, 1979–1984 (2010). [DOI] [PubMed] [Google Scholar]
  22. Kim J. et al. Three-Dimensional a-Si:H solar cells on glass nanocone arrays patterned by self-assembled Sn nanospheres. ACS Nano 6, 265–271 (2011). [DOI] [PubMed] [Google Scholar]
  23. Hsu C. M. et al. High-Efficiency Amorphous Silicon Solar Cell on a Periodic Nanocone Back Reflector. Adv. Energy Mater. 2, 628–633 (2012). [Google Scholar]
  24. Battaglia C. et al. Light trapping in solar cells: Can periodic beat random? ACS Nano. 6, 2790–2797 (2012). [DOI] [PubMed] [Google Scholar]
  25. Spinelli P., Verschuuren M. A. & Polman A. Broadband omnidirectional antireflection coating based on subwavelength surface Mie resonators. Nat. Commun. 3, 692 (2012). [DOI] [PMC free article] [PubMed] [Google Scholar]
  26. Yao Y. et al. Broadband light management using low-Q whispering gallery modes in spherical nanoshells. Nat. Commun. 3, 664 (2012). [DOI] [PubMed] [Google Scholar]
  27. Li H. B. T., Franken R. H., Rath J. K. & Schropp R. E. I. Structural defects caused by a rough substrate and their influence on the performance of hydrogenated nano-crystalline silicon n-i-p solar cells Solar Energy Mater. Solar Cells 93, 338–349 (2009). [Google Scholar]
  28. Deceglie M. G., Ferry V. E., Alivisatos A. P. & Atwater H. A. Accounting for Localized Defects in the Optoelectronic Design of Thin-Film Solar Cells. IEEE Journal of Photovoltaics 3, 599–604 (2013). [Google Scholar]
  29. Pala R. A., White J., Barnard E., Liu J. & Brongersma M. L. Design of plasmonic thin-film solar cells with broadband absorption enhancements. Adv. Mater. 21, 3504–3509 (2009). [Google Scholar]
  30. Inès M. et al. Multi-resonant absorption in ultra-thin silicon solar cells with metallic nanowires. Opt. Express 21, A372–A381 (2013). [DOI] [PubMed] [Google Scholar]
  31. Lare M. van, Lenzmann F. O., Verschuuren M. A. & Polman A. Mode coupling by plasmonic surface scatterers in thin-film silicon solar cells. Appl. Phys. Lett. 101, 221110 (2012). [Google Scholar]
  32. Vasudev A. P., Schuller J. A. & Brongersma M. L. Nanophotonic light trapping with patterned transparent conductive oxides. Opt. Express 20, A385–A394 (2012). [DOI] [PubMed] [Google Scholar]
  33. Grandidier J., Callahan D. M., Munday J. N. & Atwater H. A. Light absorption enhancement in thin-film solar cells using whispering gallery modes in dielectric nanospheres. Adv. Mater. 23, 1272–1276 (2011). [DOI] [PubMed] [Google Scholar]
  34. Grandidier J. et al. Solar cell efficiency enhancement via light trapping in printable resonant dielectric nanosphere arrays. Phys. Status Solidi A 210, 255–260 (2013). [Google Scholar]
  35. Li X. et al. Bridging electromagnetic and carrier transport calculations for three-dimensional modelling of plasmonic solar cells,”. Opt. Express 19, A888–A896 (2011). [DOI] [PubMed] [Google Scholar]
  36. Li X. et al. Multi-dimensional modeling of solar cells with electromagnetic and carrier transport calculations. Prog. Photovolt: Res. Appl. 21, 109–120 (2013). [Google Scholar]
  37. Wang C., Yu S., Chen W. & Sun C. Highly Efficient Light Trapping Structure Design Inspired By Natural Evolution. Sci. Rep. 3, 1025 (2013). [DOI] [PMC free article] [PubMed] [Google Scholar]
  38. Campbell P. & Green M. A. The limiting efficiency of silicon solar cells under concentrated light. IEEE Trans. Electron. 33, 234–239 (1986). [Google Scholar]
  39. Staebler D. L. & Wronski C. R. Optically induced conductivity changes in discharge-produced hydrogenated amorphous silicon. J. Appl. Phys. 51, 3262–3268 (1980). [Google Scholar]
  40. Rech B. & Wagner H. Potential of amorphous silicon for solar cells. Appl. Phys. A 69, 155–167 (1999). [Google Scholar]
  41. Groep J. van de. & Polman A. Designing dielectric resonators on substrates: Combining magnetic and electric resonances. Opt. Express 21, 26285–26302 (2013). [DOI] [PubMed] [Google Scholar]
  42. Jovanov V., Planchoke U., Magnus P., Stiebig H. & Knipp D. Influence of back contact morphology on light trapping and plasmonic effects in microcrystalline silicon single junction and micromorph tandem solar cells. Sol. Energy Mater. Sol. Cells 110, 49–57 (2013). [Google Scholar]
  43. Frei W. R., Johnson H. T. & Choquette K. D. Optimization of a single defect photonic crystal laser cavity. J. Appl. Phys. 103, 033102 (2008). [Google Scholar]
  44. Norato J., Haber R. B., Tortorelli D. A. & Bendsøe M. P. A geometry projection method for shape optimization. Internat. J. Numer. Methods Engrg. 60, 2289–2312 (2004). [Google Scholar]
  45. Nelder J. A. & Mead R. A simplex method for function minimization. Comput. J. 7, 308–13 (1965). [Google Scholar]

Associated Data

This section collects any data citations, data availability statements, or supplementary materials included in this article.

Supplementary Materials

Supplementary Information

New strategy to promote conversion efficiency using high-index nanostructures in thin-film solar cells

srep07165-s1.pdf (267.1KB, pdf)

Articles from Scientific Reports are provided here courtesy of Nature Publishing Group

RESOURCES