Skip to main content
NCBI home page
Scientific Reports logoLink to Scientific Reports
. 2016 Feb 2;6:20215. doi: 10.1038/srep20215

Photonic-assisted microwave signal multiplication and modulation using a silicon Mach–Zehnder modulator

Yun Long 1, Linjie Zhou 2, Jian Wang 1,a
PMCID: PMC4735760  PMID: 26832305

Abstract

Photonic generation of microwave signal is obviously attractive for many prominent advantages, such as large bandwidth, low loss, and immunity to electromagnetic interference. Based on a single integrated silicon Mach–Zehnder modulator (MZM), we propose and experimentally demonstrate a simple and compact photonic scheme to enable frequency-multiplicated microwave signal. Using the fabricated integrated MZM, we also demonstrate the feasibility of microwave amplitude-shift keying (ASK) modulation based on integrated photonic approach. In proof-of-concept experiments, 2-GHz frequency-doubled microwave signal is generated using a 1-GHz driving signal. 750-MHz/1-GHz frequency-tripled/quadrupled microwave signals are obtained with a driving signal of 250 MHz. In addition, a 50-Mb/s binary amplitude coded 1-GHz microwave signal is also successfully generated.

Photonic-assisted generation of microwave signals can find interesting applications in many microwave photonic systems, such as broad-band wireless access networks, software-defined radio, antenna remoting, phased-array antenna, and radar systems1. Usually, optical microwave generation is based on heterodyne techniques. Two phase-correlated optical waves with a wavelength spacing corresponding to the desired frequency of the microwave signal are generated, and then the microwave signal is obtained by beating the two optical wavelengths at a square-law photodetector (PD). Several approaches to generating two phase-correlated optical waves have been proposed and demonstrated based on free space devices2,3 and fiber devices1,4,5,6,7,8,9,10,11,12,13,14. Among these approaches, microwave frequency multiplication based on external modulation using Mach–Zehnder modulators (MZMs) has been considered an effective solution for high frequency and tunable microwave signal generation. For example, using a single MZM, a frequency-doubled microwave signal is generated in4 by adjusting the constant phase shift between two arms of the MZM to suppress all the even-order side bands. The beating of the ±1st-order side-bands at a PD would generate a frequency-doubled microwave signal. In addition, by introducing an optical notch filter to remove the optical carrier, a frequency-quadrupled microwave signal can also be generated1. The previous microwave generation technology using MZMs are based on bulked lithium niobate devices. The required driving voltage of the lithium niobate based MZM are relatively high. For high-order frequency-multiplicated signal generation using a single MZM, the required voltages of the driving microwave signals can be severalfold of the half-wave voltage, which are not easy to realize in practice.

Photonic generation of radio frequency (RF) binary digital modulation signals is another key technology in microwave photonics. Amplitude-shift keying (ASK), phase-shift keying (PSK) and frequency-shift keying (FSK) are basic modulation formats in wireless communications, which convey information by modulating the amplitude, phase or frequency of a continuous carrier wave. Traditionally, these modulated microwave signals are generated in electrical domain using digital electronic circuits15. Due to the electronic bottleneck, the major difficulty of this traditional technique is that the frequency of the generated signals is limited to a few GHz. An effective method to generate high frequency RF signals is to generate RF signals in the optical domain16,17,18. These approaches are based on spatial light modulator (SLM) technologies or fiber devices. Similar to microwave frequency mulitiplication, the use of MZM is also considered to be a competitive approach to generating binary digital modulation signals. Microwave PSK and FSK signals have been proposed and realized based on commercial MZMs16,17,18. However, microwave ASK signal as a fundamental digital modulation format in wireless communication has rarely been realized using MZM.

Compared to free space or fiber-based devices to generate frequency-multiplicated microwave signals or binary digital modulation signals, silicon-on-insulator (SOI) based waveguides can offer distinct advantages of increased stability and reliability, low cost, small footprints, and compatibility with other integrated optoelectronic devices19. In recent years, owing to the great success of silicon photonics, some passive microwave photonic devices (i.e. microwave photonic filters, microwave photonic phase shifters) based on SOI waveguides have been proposed and demonstrated showing excellent characteristics20,21,22,23,24,25,26,27.

In this paper, we propose a simple yet effective scheme to obtain frequency- multiplicated microwave signals or amplitude coded microwave signals based on a single integrated silicon MZM. In proof-of-concept experiments, 2-GHz frequency-doubled microwave signal is generated using a 1-GHz driving signal. 750-MHz/1-GHz frequency-tripled/quadrupled microwave signals are obtained with a driving signal of 250 MHz. Moreover, a 50-Mb/s binary amplitude coded 1-GHz microwave signal is also successfully generated in the experiment.

Results

Photonic-assisted microwave signal multiplication

Figure 1 illustrates the schematic illustration of the proposed photonic frequency-multiplicated microwave signal generation system using an integrated silicon MZM. Continuous-wave (CW) light from a tunable laser diode (TLD) is sent to the MZM. The driving signal and the DC-bias are combined by a bias-tee and applied to the MZM. The output light intensity of the MZM can be written as

Figure 1. Schematic illustration of the photonic frequency-multiplicated microwave signal generation system using an integrated silicon MZM.

Figure 1

Open in a new tab

TLD, tunable laser diode; PC, polarization controller; EDFA: erbium-doped fiber amplifier; VOA: variable optical attenuator; PD: photodetector.

graphic file with name srep20215-m1.jpg

where I0 is the intensity of the input optical carrier. φ0 = πVb /Vπis the constant phase difference between the two arms determined by the constant DC-bias voltage Vb. Vπ is the half-wave voltage of the MZM. VRF and ωRF are the amplitude and angular frequency of the applied electrical drive voltage, respectively. Based on the Jacobi–Anger expansions, Eq. (1) can be expanded to be

graphic file with name srep20215-m2.jpg

where m = πVRF/Vπ is the modulation indice of the MZM. Jn is the nth order Bessel function of the first kind.

It follows from Eq. (2) that if the modulator is biased at Vπ, the odd components will be suppressed. Ignoring the high order harmonic wave, a frequency-doubled microwave signal is obtained. In addition, by adjusting the driving microwave signal amplitude to let J2(m) = 0, the quadruple response will dominant the output, and a frequency-quadrupled signal can be obtained. Similarly, a frequency-tripled signal is generated by suppressing the even components and J1(m) term of the signal.

Figure 2(a) shows the optical microscope image of the fabricated device. The waveguides are 220 nm high with a 60 nm slab. The width of the waveguide is 500 nm. The active arm length is 1.8 mm while the arm length difference between two arms are 494 μm. Figure 2(b) shows the cross-sectional view schematics of the doped waveguide.The n and p doping regions are 4 μm wide, and each has a separation of 0.6 μm from the waveguide sidewall. The doping concentration is about 1020 cm−3. Vertical grating couplers are used to couple light in/out of the silicon chip and ensure operation with transverse electric (TE) polarized light. The grating coupling loss is about 7 dB per facet.

Figure 2.

Figure 2

Open in a new tab

(a) Microscope image of the fabricated integrated MZM. (b) Cross-sectional view schematics of the doped waveguide.

We first investigate the generation of frequency-doubled microwave signal. Figure 3(a,b) show the waveforms of the original 500-MHz driving signal and the generated 1-GHz signal. Figure 3(c,d) show the obtained 2-GHz signal when the driving signal frequency is 1 GHz. Figure 4 illustrates the results of the generation of frequency-tripled and frequency- quadrupled signal with a driving signal of 250 MHz. The imperfections of the waveforms come from the influence of incompletely suppressed high-order components.

Figure 3.

Figure 3

Open in a new tab

Waveforms of (a) the input 500-MHz driving signal, (b) the generated 1-GHz frequency-doubled signal, (c) the input 1-GHz driving signal, and (d) the generated 2-GHz frequency-doubled signal.

Figure 4.

Figure 4

Open in a new tab

Waveforms of (a) the input 250-MHz driving signal, (b) the generated 750-MHz frequency-tripled signal, and (c) the 1-GHz frequency-quadrupled signal.

Photonic-assisted microwave ASK modulation

Using the fabricated integrated MZM, we also demonstrate the feasibility of microwave ASK modulation using integrated photonic approach. Figure 5 illustrates the schematic illustration of the proposed photonic microwave ASK signal modulation system using an integrated silicon MZM. The microwave carrier signal and the binary coding signal s (t) are applied to the two RF ports of the MZM, respectively. The AC term of the detected signal at the output of the PD can be written as

Figure 5. Schematic illustration of the proposed photonic microwave ASK signal generator.

Figure 5

Open in a new tab
graphic file with name srep20215-m3.jpg

where ωRF, m, VRF, Vπ and φ0are defined as previously mentioned. γ = πVs/Vπis the modulation index in the arm where the binary coding signal is applied. Assuming φ0 = 0, Eq. (3) can be simplified as

graphic file with name srep20215-m4.jpg

The second term in Eq. (4) is located in the baseband which can be easily eliminated by an electric filter. Assuming γ = π/2, the amplitude of the obtained signal is

graphic file with name srep20215-m5.jpg

As can be seen, the amplitude of the carrier is “1” with bit “1”, and “0” with bit “0”. Therefore, two-level microwave ASK signal is generated.

Figure 6(a) shows the waveforms of the original 50-Mb/s baseband signal with a pattern of “110100101101001011”. The original 1-GHz microwave carrier is shown in Fig. 3(b). Figure 3(c) shows the modulated microwave ASK signal. The obtained results shown in Figs 3, 4 and 6 indicate the successful implementation of photonic-assisted microwave signal multiplication and modulation using a compact silicon MZM.

Figure 6.

Figure 6

Open in a new tab

Waveforms of (a) the original 50-Mb/s baseband signal with a pattern of “110100101101001011”, (b) original 1-GHz microwave carrier signal, and (c) the output microwave ASK signal.

Discussion

In summary, a simple and compact photonic scheme to obtain frequency-multiplicated microwave signal has been proposed and experimentally demonstrated based on a single integrated silicon MZM. In a proof-of-concept experiment, 2-GHz frequency-doubled microwave signal is generated using a 1-GHz driving signal. Also, 750-MHz/1-GHz frequency-tripled/quadrupled microwave signals are obtained with a driving signal of 250 MHz. Furthermore, using the fabricated integrated silicon MZM, the feasibility of microwave ASK modulation has also been demonstrated. A 50-Mb/s binary amplitude coded 1-GHz microwave signal is successfully generated. The frequency of the generated microwave signals is limited by the operation bandwidth of the pin-type MZM. For the MZM design, 2 design parameters, i.e. doping structures and the length of the MZM, could influence the system performance. Using pin-type doping might reduce the requirement of input signal amplitude. However, realizing high frequency multiplication and ASK signal modulation is a great challenge. By using pn-type doping, the bandwidth could be effectively improved28, while the high requirement of input signal amplitude is difficult to satisfy. Extending the length of the arms of MZM might alleviate the requirement of input signal amplitude, but could suffer from extra loss. To enable high frequency microwave signal multiplication and ASK signal generation, a high bandwidth, low half-wave voltage, and low loss MZM is needed, which might be realized by employing some other doping structures such as zigzag structure to increase the modulation efficiency29. With future improvement, one would also expect to see high frequency microwave signal generation/modulation and other photonic-assisted microwave signal processing applications exploiting compact integrated silicon photonic devices.

Method

Devices fabrication

We employ a single MZM to generate various microwave signals. The designed MZM is fabricated on an SOI wafer. The thickness of the top silicon and the buried oxide layer of the SOI wafer are 220 nm and 2 mm, respectively. A deep ultra-violet (DUV) photolithography process is employed to define the waveguide patterns, followed by anisotropic dry etch of silicon. Boron and phosphorus ion implantations were performed to form the p -type and n-type doped regions. Finally, contact holes were etched and aluminum was deposited to form the metal connection. We use vertical grating coupling method to couple the fiber and the silicon chip. The whole fabrication process is done using CMOS compatible processes.

Additional Information

How to cite this article: Long, Y. et al. Photonic-assisted microwave signal multiplication and modulation using a silicon Mach–Zehnder modulator. Sci. Rep. 6, 20215; doi: 10.1038/srep20215 (2016).

Acknowledgments

This work was supported by the National Natural Science Foundation of China (NSFC) under grants 61222502 and 11574001, the Program for New Century Excellent Talents in University (NCET-11-0182), the Wuhan Science and Technology Plan Project under grant 2014070404010201, and the seed project of Wuhan National Laboratory for Optoelectronics (WNLO). The authors would like to thank Shuhui Li for technical supports and helpful discussions.

Footnotes

Author Contributions J.W. and Y.L. developed the concept. L.J.Z. prepared the samples. Y.L. carried out the experiments. Y.L. and J.W. analyzed the data and wrote the manuscript. J.W. supervised the project.

References

  1. Qi G., Yao J., Seregelyi J., Paquet S. & Bélisle C. Generation and distribution of a wide-band continuously tunable millimeter-wave signal with an optical external modulation technique. IEEE Trans. Microwave Theory Tech. 53, 3090–3097 (2005). [Google Scholar]
  2. Goldberg L., Taylor H., Weller J. & Bloom D. Microwave signal generation with injection-locked laser diodes. Electron. Lett. 19, 491–493 (1983). [Google Scholar]
  3. Ramos R. & Seeds A. Fast heterodyne optical phase-lock loop using double quantum well laser diodes. Electron. Lett. 28, 82–83 (1992). [Google Scholar]
  4. O’reilly J., Lane P., Heidemann R. & Hofstetter R. Optical generation of very narrow linewidth millimetre wave signals. Electron. Lett. 28, 2309–2311 (1992). [Google Scholar]
  5. O’Reilly J. & Lane P. Remote delivery of video services using mm-waves and optics. J. Lightwave Technol. 12, 369–375 (1994). [Google Scholar]
  6. Qi G., Yao J., Seregelyi J., Paquet S. & Bélisle C. Optical generation and distribution of continuously tunable millimeter-wave signals using an optical phase modulator. J. Lightwave Technol. 23, 2687–2695 (2005). [Google Scholar]
  7. Yu J. et al. Optical millimeter-wave generation or up-conversion using external modulators. IEEE Photon. Technol. Lett. 18, 265–267 (2006). [Google Scholar]
  8. Li W. & Yao J. Investigation of photonically assisted microwave frequency multiplication based on external modulation. IEEE Trans. Microwave Theory Tech. 58, 3259–3268 (2010). [Google Scholar]
  9. Gao L., Liu W., Chen X. & Yao J. Photonic-assisted microwave frequency multiplication with a tunable multiplication factor. Opt. Lett. 38, 4487–4490 (2013). [DOI] [PubMed] [Google Scholar]
  10. Chen B., Zheng S., Chi H., Zhang X. & Jin X. An optical millimeter-wave generation technique based on phase modulation and Brillouin-assisted notch-filtering. IEEE Photon. Technol. Lett. 20, 2057–2059 (2008). [Google Scholar]
  11. Wiberg A., Pérez-Millán P., Andrés M. V. & Hedekvist P. O. Microwave-photonic frequency multiplication utilizing optical four-wave mixing and fiber Bragg gratings. J. Lightwave Technol. 24, 329 (2006). [Google Scholar]
  12. Zhang C., Wang L. & Qiu K. Proposal for all-optical generation of multiple-frequency millimeter-wave signals for RoF system with multiple base stations using FWM in SOA. Opt. Express 19, 13957–13962 (2011). [DOI] [PubMed] [Google Scholar]
  13. Vidal B. Photonic millimeter-wave frequency multiplication based on cascaded four-wave mixing and polarization pulling. Opt. Lett. 37, 5055–5057 (2012). [DOI] [PubMed] [Google Scholar]
  14. Zheng J. et al. Photonic-assisted microwave frequency multiplier based on nonlinear polarization rotation. Opt. Lett. 39, 1366–1369 (2014). [DOI] [PubMed] [Google Scholar]
  15. Xiang P., Zheng X., Zhang H., Li Y. & Chen Y. A novel approach to photonic generation of RF binary digital modulation signals. Opt. Express 21, 631–639 (2013). [DOI] [PubMed] [Google Scholar]
  16. Tang Z., Zhang T., Zhang F. & Pan S. Photonic generation of a phase-coded microwave signal based on a single dual-drive Mach–Zehnder modulator. Opt. Lett. 38, 5365–5368 (2013). [DOI] [PubMed] [Google Scholar]
  17. Cao P. et al. Photonic generation of microwave frequency shift keying signal using a single-drive Mach–Zehnder modulator. Opt. Express 22, 14433–14440 (2014). [DOI] [PubMed] [Google Scholar]
  18. Chou J., Yan H. & Jalali B. Adaptive RF-photonic arbitrary waveform generator. IEEE Photon. Technol. Lett. 15, 581–583, 10.1109/LPT.2003.809309 (2003). [DOI] [Google Scholar]
  19. Jalali B. & Fathpour S. Silicon photonics. J. Lightwave Technol. 24, 4600–4615 (2006). [Google Scholar]
  20. Alipour P. et al. Fully reconfigurable compact RF photonic filters using high-Q silicon microdisk resonators. Opt. Express 19, 15899–15907 (2011). [DOI] [PubMed] [Google Scholar]
  21. Zhang D. et al. Tunable and Reconfigurable Bandstop Microwave Photonic Filter Based on Integrated Microrings and Mach–Zehnder Interferometer. J. Lightwave Technol. 31, 3668–3675 (2013). [Google Scholar]
  22. Palací J., Villanueva G. E., Galán J. V., Marti J. & Vidal B. Single bandpass photonic microwave filter based on a notch ring resonator. IEEE Photon. Technol. Lett. 22, 1276–1278 (2010). [Google Scholar]
  23. Rasras M. S. et al. Demonstration of a tunable microwave-photonic notch filter using low-loss silicon ring resonators. J. Lightwave Technol. 27, 2105–2110 (2009). [Google Scholar]
  24. Lloret J. et al. Tunable complex-valued multi-tap microwave photonic filter based on single silicon-on-insulator microring resonator. Opt. Express 19, 12402–12407 (2011). [DOI] [PubMed] [Google Scholar]
  25. Zhang D., Feng X. & Huang Y. Tunable and reconfigurable bandpass microwave photonic filters utilizing integrated optical processor on silicon-on-insulator substrate. IEEE Photon. Technol. Lett. 24, 1502–1505 (2012). [Google Scholar]
  26. Pu M. et al. Widely tunable microwave phase shifter based on silicon-on-insulator dual-microring resonator. Opt. Express 18, 6172–6182 (2010). [DOI] [PubMed] [Google Scholar]
  27. Pu M. et al. Tunable microwave phase shifter based on silicon-on-insulator microring resonator. IEEE Photon. Technol. Lett. 22, 869–871 (2010). [DOI] [PubMed] [Google Scholar]
  28. Thomson D. J. et al. High contrast 40Gbit/s optical modulation in silicon. Opt. Express 19, 11507–11516 (2011). [DOI] [PubMed] [Google Scholar]
  29. Xiao X. et al. 44-Gb/s silicon microring modulators based on zigzag PN junctions. IEEE Photon. Technol. Lett. 24, 1712–1714 (2012). [Google Scholar]

Articles from Scientific Reports are provided here courtesy of Nature Publishing Group

RESOURCES