Skip to main content
PMC home page
Scientific Reports logoLink to Scientific Reports
. 2016 Jul 4;6:29341. doi: 10.1038/srep29341

Highly conductive and flexible color filter electrode using multilayer film structure

Jun Hee Han 1, Dong-Young Kim 1, Dohong Kim 1, Kyung Cheol Choi 1,a
PMCID: PMC4931689  PMID: 27373804

Abstract

In this paper, a high performance flexible component that serves as a color filter and an electrode simultaneously is suggested. The suggested highly conductive and flexible color filter electrode (CFE) has a multilayer film structure composed of silver (Ag) and tungsten trioxide (WO3). The CFE maintained its color filtering capability even when the films were bent on a polyethylene terephthalate (PET) film. Low sheet resistance of the CFE was obtained using WO3 as a bridge layer that connects two Ag layers electrically. The sheet resistance was less than 2 Ω/sq. and it was negligibly changed after bending the film, confirming the flexibility of the CFE. The CFE can be easily fabricated using a thermal evaporator and is easily patterned by photolithography or a shadow mask. The proposed CFE has enormous potential for applications involving optical devices including large area devices and flexible devices.

As display technologies such as organic light-emitting diodes and liquid crystal displays are receiving a great deal of attention, and with advances in image sensing technologies, color filters have become important device components. A color filter is a type of band-pass filter and it is normally made of organic dyes or pigments in industrial use. However, such color filters have low chemical stability and color degraded by the influence of ultraviolet and strong light intensities1,2,3. In efforts to solve these problems, many studies on optical color filters have been conducted. Plasmons from metallic nanostructures are used to make optical color filters4,5,6,7,8,9,10, and guided mode resonance is one of the ways used to implement optical color filters11,12,13,14,15. An electrode is another important element of optical devices and electronics. Although indium tin oxide (ITO) is usually used as an electrode in optical devices and electronics, its sheet resistance is dramatically changed after being bent, thus illustrating that ITO is not a suitable electrode for flexible electronics. To produce electrodes for flexible devices, alternative flexible electrodes such as metal nanowires16,17, graphene18,19 , and conductive polymers20,21 have been studied.

In this study, a high performance flexible component that operates as an electrode and a color filter simultaneously has been developed. Compared with previously reported components22,23,24, flexibility is achieved for the first time and the proposed color filter electrode (CFE) has remarkably low sheet resistance of less than 2 Ω/sq. The optical and electrical properties were negligibly changed after a bending test, demonstrating that the CFE can be exploited in optical flexible devices. The low sheet resistance confirms its high conductivity and it shows potential as an electrode for large area optoelectronics. The low sheet resistance is realized by the use of tungsten oxide (WO3) to allow two silver (Ag) films to be electrically connected. The electrical connection of the Ag layers through WO3 was analyzed theoretically and experimentally in this paper. The CFE, which is composed of multiple thin films with tungsten trioxide (WO3) and silver (Ag), uses guided mode resonance to realize the color filter, thereby maintaining the advantages of an optical color filter. By varying the thicknesses of the layers, other colors except red, green, and blue (RGB) also can be realized easily. In order to fabricate the CFE, additional modification of existing fabrication systems is not necessary because it can be easily prepared by thermal deposition. Patterning is also easily realized. A photolithography method and a shadow mask, which are commonly used for patterning in industrially, could be applied to the CFE and sub-10 Inline graphicm patterning of the CFE was confirmed experimentally.

Results and Discussion

Figure 1(a) schematically illustrates the CFE suggested in this paper. As shown in the figure, the structure is composed of a multilayer composed of Ag and WO3. The thickness of the bottom Ag layer was 20 nm and that of the top Ag layer was 10 nm. Although the thicknesses of the Ag layers were fixed in this study, the sheet resistance and transmittance of CFE could be altered by adopting different Ag thicknesses (Supplementary Figure 1, Supplementary Figure 2, Supplementary Table 1). The filtered color can be altered by varying the thickness of the dielectric layer located between two metal layers because of the cavity resonance14,25,26,27,28. Moreover, higher transmittance can be obtained by optimizing the layer thickness of the outer layer, which is located at the outside of the metal layer because this layer provides anti-reflection15,22,29. Furthermore, the outer layer reduces the difference of the admittance between the CFE and the incident medium when it has an optimized thickness22, reducing the reflection and improving the transmittance. Therefore, a 5-layer structure was adopted in this study to achieve saturation of filtered color. In order to optimize the thicknesses of the WO3 layers for the RGB color filter, MATLAB was used to calculate the characteristic matrix (Supplementary Figure 3, Supplementary Table 2)30. The refractive indices of Ag and WO3 were measured experimentally (Supplementary Figure 4). The optimized layer thicknesses obtained from the calculation for the RGB CFE are shown in Table 1.

Figure 1. Schematic and characterization of fabricated devices.

Figure 1

Open in a new tab

(a) Graphical representation of the conductive and flexible CFE with a multilayer structure consisting of silver and tungsten trioxide (WO3) on a polyethylene terephthalate (PET) substrate. (b) Transmittance of red, green, and blue CFE with optimized WO3 thickness. The solid lines with red, green, and blue are the calculated data. Red colored squares, green colored diamonds, and blue colored circles are experimental data of the red, green, and blue CFEs on a glass substrate, respectively. Red empty triangles, green empty circles, and blue empty inverted triangles are experimental data of the red, green, and blue CFEs on a PET substrate, respectively. (c) Images of the realized CFEs. The first column shows the red, green, and blue CFEs on glass substrates, from left to right. The second column shows the red, green, and blue CFEs on PET substrates, from left to right. (d) Scanning electron microscope (SEM) images of red, green, and blue CFEs in cross section view. The thickness of each layer is indicated on the SEM images.

Table 1. The optimized layer thicknesses of RGB CFEs.

Color 1st WO3 Bottom Ag 2nd WO3 Top Ag 3rd WO3
RED 72 nm 20 nm 115 nm 10 nm 84 nm
GREEN 87 nm 20 nm 84 nm 10 nm 92 nm
BLUE 100 nm 20 nm 46 nm 10 nm 100 nm
Open in a new tab

Figure 1(b) shows the calculated and experimental transmittance results for the RGB CFEs with the optimized layer thicknesses. As Fig. 1(b) shows, the transmittance data of the RGB CFEs fabricated on glass and PET had similar transmittance to that obtained by calculation. Fig. 1(c) shows the optimized RGB CFEs fabricated on glass (first column) and polyethylene terephthalate (PET) film (second column). When the CFE was forcibly bent, its optical properties were maintained (Supplementary Video 1). When color coordinates of the RGB CFEs were calculated using transmittance data by the color matching function and plotted on the CIE 1931, the points are located on the red, green, and blue regions (Supplementary Figure 5).

Figure 1(d) shows scanning electron microscope (SEM) images of RGB CFE cross-sectional views. The indicated thicknesses on the SEM images were measured by the software of the SEM system and redrawn for clear visibility. The thicknesses of each film observed from the SEM image were similar to the values reported in Table 1. Other CFEs that have different color aside from RGB could be made with different thicknesses of the WO3 film (Supplementary Figure 6, Supplementary Table 3).

One of the key advantages of the suggested CFE is that it can be easily fabricated. As the Ag and WO3 films could be deposited by a thermal evaporation method, the CFE can be made in situ inside a thermal vacuum chamber. Also, the device can be enlarged to as much as the permissible range of the thermal vacuum chamber. A 70 mm by 70 mm size CFE, which corresponded with the largest size possible in our laboratory, was made on a PET substrate (Fig. 2(a)).

Figure 2. Electrical and mechanical properties of CFEs.

Figure 2

Open in a new tab

(a) Images of large sized red, green, and blue CFEs working as a part of an electrical circuit, from left to right. (b) Sheet resistance measurement of CFE. (c) Schematic diagrams of the energy band structure of WO3 and Ag metal. (d) Sheet resistance changes after 10 mm radius bending test.

A bending test was conducted to check the changes of transmittance after bending, and it was found that the transmittance was negligibly changed after a 10 mm radius, 10,000 cycle bending test, thus verifying its flexibility (Supplementary Figure 7).

Figure 2(a) shows the conductivity of the RGB CFE by having the light emitting diodes (LED) emit light using the RGB CFE as the circuit line. The sheet resistance was measured by using a 4-probe after the entire CFE structure was fabricated. As presented in Fig. 2(b), the CFE provides 1.62 Ω/sq. sheet resistance (Supplementary Figure 8). The RGB CFEs have almost the same sheet resistances due to having the same Ag layer thicknesses. Considering that the sheet resistance of the CFE is about 1.66 Ω/sq. when a 20 nm thick Ag layer with resistance of 1.99 Ω/sq. and a 10 nm thick Ag layer with resistance of 10.22 Ω/sq. are connected electrically in parallel, the measured sheet resistance,1.62 Ω/sq., verifies that the two Ag layers embedded in the CFE were connected electrically (Supplementary Figure 1, Supplementary Figure 9)31. Considering that the sheet resistance of ITO is about 10 Ω/sq.29, the sheet resistance of the CFE shows better electrical properties than an ITO electrode. The proposed CFE could be applied to large area displays or electronics, because they require an electrode that has low sheet resistance for lower current loss.

The electrical connection between the two separated Ag layers is attributed to the WO3 film placed between the two Ag layers. Figure 2(c) schematically illustrates energy band structures that would be expected before and after the contact of Ag and WO3 layers32,33,34. After the layers are brought into contact, the Fermi levels align at equilibrium in the ideal case according to the classic metal-semiconductor contact theory. Because of band bending at the contact interface, barriers to electron flow between the Ag and WO3 layers are low, as shown in Fig. 2(c), and the electrons easily flow between the two Ag layers through the WO3 film. Supplementary Figure 10 shows experimental results, validating that the WO3 layer connects two Ag layers electrically.

The CFE fabricated with large size maintained its conductive property while being subjected to bending (Supplementary Video 2). Figure 2(d) shows the change of the sheet resistance of RGB CFEs after a 10 mm radius bending test with the number of bending cycles. The sheet resistances were changed by less than 1 Ω/sq. after 10,000 bending cycles, showing better performance than an ITO electrode, which cracks when bent29,35,36. This shows the potential of the CFE as a flexible electrode. As the CFEs became thicker, the films suffered more tensile stress even though they were bent with the same bending radius37. With greater tensile stress, there is a stronger likelihood of cracks forming inside the device, and accordingly the sheet resistance of the red CFEs changed slightly more than that of the other CFEs. However, the sheet resistance change was saturated because the applied stress to the CFEs appears not to exceed the fatigue strength during the 10,000 bending cycles with a 10 mm bending radius, where the crack size remained unchanged38.

The CFE suggested in this paper could be easily patterned by photolithography because Ag and WO3 do not chemically react with acetone, which is used to strip the photoresist (PR). Figure 3(a) schematically illustrates the flow of the CFE patterning process. A negative PR was used as a patterning mask because it has a reversed trapezoidal shape when patterned, as shown in Fig. 3(b). By using the pattering method described in Fig. 3(a), 10 Inline graphic-width line patterns of the CFEs were obtained and the sharp edge of the patterned CFE can be confirmed in Fig. 3(b,c). A sub-ten nanometer sized pattern on the CFE might be possible if the scale of the PR pattern width is sufficiently small.

Figure 3. Patterning of the CFE.

Figure 3

Open in a new tab

(a) Schematic flow of CFE patterning. (b) Scanning electron microscope (SEM) image of a cross section view of deposited CFE on the patterned photoresist. (c) SEM image of a tilted view of patterned CFE.

In order to verify that the electrical and optical properties of the CFE were not changed after patterning, the sheet resistances and transmittances of the CFE were evaluated after sonication cleaning with acetone. Figure 4(a) shows that the sheet resistances were not affected by acetone cleaning and Fig. 4(b) shows the CFEs have the same transmittances with and without acetone cleaning. These results confirmed that the electrical and optical properties of the CFE were not changed after the patterning with PR. As Ag and WO3 were deposited by thermal evaporation, a shadow mask also could be used for the patterning step. Figure 2(a) shows how a shadow mask works for the patterning. It is seen that three lines of the CFE on a PET substrate were made by the shadow mask. By virtue of the easy patterning methods, it is anticipated that the CFE can be easily applied to various industries.

Figure 4. Changes to electrical and optical characteristics of CFEs after acetone cleaning.

Figure 4

Open in a new tab

(a) Sheet resistances of red, green, and blue CFE after acetone cleaning with different acetone cleaning time. Red squares indicate the red CFE and green circles indicate the green CFE. Blue triangles indicate the blue CFE. (b) Transmittances of red, green, and blue CFEs after 30 min acetone cleaning. Red colored squares, green colored diamonds, and blue colored circles indicate the transmittances of red, green, and blue CFEs before acetone cleaning, respectively. Red open triangles, green open circles, and blue inverted open triangles indicate the transmittances of red, green, and blue CFEs after 30 min acetone cleaning, respectively.

In summary, a high performance flexible component that serves as an electrode and a color filter simultaneously is fabricated by a thermal evaporation method. The electrical and optical properties of the proposed CFE were maintained after a bending test, thus confirming its flexibility. Also, the pattern of the CFE was easily obtained by photolithography or a shadow mask without altering its electrical and optical characteristics. The CFE suggested in this paper is expected to have a significant impact on the field of display devices, including organic light emitting diodes, liquid crystal displays, and electrophoretic displays. Flexible optoelectronics and large area optoelectronics are another possible field of application of the suggested CFE, as well as CMOS photo sensors and color decoration devices.

Methods

Device fabrication

The suggested CFE was manufactured on a cleaned glass substrate and a PET substrate. The thickness of the glass was 700 Inline graphic and that of the PET was 125 Inline graphic. The WO3 (1–4 mm pcs 4N, TASCO) and Ag (3–5 mm granule 4N, TASCO) were deposited by thermal evaporation with a vacuum pressure of less than 7 Inline graphic 10−6 Torr.

Device characterization

The transmittance spectrum of the CFE at normal incidence was measured by a UV-Vis spectrometer (UV-2550, SHIMADZU). The sheet resistance of the CFE was measured by a 4-point probe (FFP-2400, DASOLENG). A bending test was conducted using a bending machine (Bending system, Custom-made set-up).

Device patterning

Negative photoresist (NR9-3000PY, FUTURREX INC.) was spin-coated on cleaned glass. In order to coat the photoresist on glass, the sample was accelerated to 2000 RPM for 2 seconds and maintained for 5 seconds, and then accelerated to 4000 RPM for 5 seconds and maintained for 40 seconds. After the spin-coating step, the photoresist was soft-baked at 150 °C for 3 minutes inside an oven. The samples were exposed to ultraviolet light (UV) with a 360 mJ/cm2 exposure dose. The photoresist was then baked again at 110 °C inside the oven for 2 minutes. After the baking process, the photoresist was developed for 17 seconds in an AZ300MIF developer. After the photoresist was patterned, multilayers were deposited on the patterned photoresist sample, and then the photoresist was stripped by acetone sonication cleaning for 10 minutes.

Calculation for the optimized layer thickness

Calculation of the transmittance and optimized layer thickness was performed using MATLAB based on the characteristic matrix method. See supplementary information for more details.

Material refractive indices

The refractive indices of Ag and WO2 were measured experimentally by a spectroscopic ellipsometer (M2000D).

Additional Information

How to cite this article: Han, J. H. et al. Highly conductive and flexible color filter electrode using multilayer film structure. Sci. Rep. 6, 29341; doi: 10.1038/srep29341 (2016).

Supplementary Material

Supplementary Information
srep29341-s1.pdf (1.2MB, pdf)
Supplementary Movie S1
Download video file (1,019.1KB, avi)
Supplementary Movie S2
Download video file (2.1MB, avi)

Acknowledgments

This work was supported by the National Research Foundation of Korea (NRF) grant funded by the Korea government(MSIP)(CAFDC 5-1(0), NRF-2007-0056090). This work was supported by LG Display under LGD-KAIST Incubation Program. This work was supported by KAIST College of Engineering under Initiative Fusion Research Program.

Footnotes

Author Contributions J.H.H. conceived the entire experimental strategy and prepared the experimental samples and performed the characterization and analyses. D.-Y.K. contrived the analysis of the electrical properties of the structure. D.H.K. contributed to the calculation and analyzed the optical properties. J.H.H., D.-Y.K. and D.H.K. collaborated for preparation of the main paper and the Supplementary Information. All authors discussed the results and commented on the manuscript. All authors have given their approval of the final version of the manuscript.

References

  1. Sabnis R. W. Color filter technology for liquid crystal displays. Displays 20, 119–129 (1999). [Google Scholar]
  2. Sugiura T. Development of pigment dispersed type color filters for LCDs. J. Soc. Inf. Disp. 1, 341–346 (1993). [Google Scholar]
  3. Sugiurs T. Dyed color filters for liquid-crystal displays. J. Soc. Inf. Disp. 1, 177–180 (1993). [Google Scholar]
  4. Do Y. S. et al. Plasmonic Color Filter and its Fabrication for Large-Area Applications. Adv. Opt. Mater. 1, 109–109 (2013). [Google Scholar]
  5. Ellenbogen T., Seo K. & Crozier K. B. Chromatic Plasmonic Polarizers for Active Visible Color Filtering and Polarimetry. Nano Lett. 12, 1026–1031 (2012). [DOI] [PubMed] [Google Scholar]
  6. Genet C. & Ebbesen T. W. Light in tiny holes. Nature 445, 39–46 (2007). [DOI] [PubMed] [Google Scholar]
  7. Lee H.-S., Yoon Y.-T., Lee S.-S., Kim S.-H. & Lee K.-D. Color filter based on a subwavelength patterned metal grating. Opt. Express 15, 15457–15463 (2007). [DOI] [PubMed] [Google Scholar]
  8. Wu Y.-K. R., Hollowell A. E., Zhang C. & Guo L. J. Angle-insensitive structural colours based on metallic nanocavities and coloured pixels beyond the diffraction limit. Sci. Rep. 3, 1194 (2013). [DOI] [PMC free article] [PubMed] [Google Scholar]
  9. Xu T., Wu Y.-K., Luo X. & Guo L. J. Plasmonic nanoresonators for high-resolution colour filtering and spectral imaging. Nat. Commun. 1, 1–5 (2010). [DOI] [PubMed] [Google Scholar]
  10. Yokogawa S. & Burgos S. P. & Atwater, H. a. Plasmonic color filters for CMOS image sensor applications. Nano Lett. 12, 4349–4354 (2012). [DOI] [PubMed] [Google Scholar]
  11. Frey L., Parrein P., Virot L., Pellé C. & Raby J. Thin film characterization for modeling and optimization of silver-dielectric color filters. Appl. Opt. 53, 1663–73 (2014). [DOI] [PubMed] [Google Scholar]
  12. Kedawat G., Jain V. K., Srivastava S. & Vijay Y. K. A novel high transmittance red color filter: ZnS and Ag multilayer. SOLID STATE Phys. Proc. 57TH DAE SOLID STATE Phys. Symp. 1512, 760 (2013). [Google Scholar]
  13. Kedawat G., Jain V. K. & Vijay Y. K. Fabrication of metal dielectric metal multilayer thin film: Color filter. SOLID STATE Phys. Proc. 58th DAE Solid State Phys. Symp. 2013 1591, 1024–1026 (2014). [Google Scholar]
  14. Kedawat G., Kumar P., Vijay Y. K. & Gupta B. K. Fabrication of highly efficient resonant structure assisted ultrathin artificially stacked Ag/ZnS/Ag multilayer films for color filter applications. J. Mater. Chem. C 3, 6745–6754 (2015). [Google Scholar]
  15. Yang C. et al. Compact Multilayer Film Structure for Angle Insensitive Color Filtering. Sci. Rep. 5, 9285 (2015). [DOI] [PMC free article] [PubMed] [Google Scholar]
  16. Garnett E. C. et al. Self-limited plasmonic welding of silver nanowire junctions. Nat. Mater. 11, 241–249 (2012). [DOI] [PubMed] [Google Scholar]
  17. Wu H. et al. A transparent electrode based on a metal nanotrough network. Nat. Nanotechnol. 8, 421–425 (2013). [DOI] [PubMed] [Google Scholar]
  18. Lee B. H. et al. SI_Graphene-conducting polymer hybrid transparent electrodes for efficient organic optoelectronic devices. Adv. Funct. Mater. 24, 1847–1856 (2014). [Google Scholar]
  19. Kim K. S. et al. Large-scale pattern growth of graphene films for stretchable transparent electrodes. Nature 457, 706–10 (2009). [DOI] [PubMed] [Google Scholar]
  20. Xia Y., Sun K. & Ouyang J. Solution-Processed Metallic Conducting Polymer Films as Transparent Electrode of Optoelectronic Devices. Adv. Mater. 24, 2436–2440 (2012). [DOI] [PubMed] [Google Scholar]
  21. Kim N. et al. Highly Conductive PEDOT:PSS Nanofibrils Induced by Solution-Processed Crystallization. Adv. Mater. 26, 2268–2272 (2014). [DOI] [PubMed] [Google Scholar]
  22. Park C.-S., Shrestha V. R., Lee S.-S., Kim E.-S. & Choi D.-Y. Omnidirectional color filters capitalizing on a nano-resonator of Ag-TiO2-Ag integrated with a phase compensating dielectric overlay. Sci. Rep. 5, 8467 (2015). [DOI] [PMC free article] [PubMed] [Google Scholar]
  23. Lee K.-T., Fukuda M., Joglekar S. & Guo J. Colored, see-through perovskite solar cells employing an optical cavity. J. Mater. Chem. C 4, 1166–1169 (2015). [Google Scholar]
  24. Lee J. Y., Lee K.-T., Seo S. & Guo L. J. Decorative power generating panels creating angle insensitive transmissive colors. Sci. Rep. 4, 4192 (2014). [DOI] [PMC free article] [PubMed] [Google Scholar]
  25. Yang C., Shen W., Zhang Y., Ye Z. & Zhang X. Color-tuning method by filling porous alumina membrane using atomic layer deposition based on metal – dielectric – metal structure. Appl. Opt. 53, A142–A147 (2014). [DOI] [PubMed] [Google Scholar]
  26. Minas G., Ribeiro J. C., Martins J. S., Wolffenbuttel R. F. & Correia J. H. An array of Fabry-Perot optical-channels for biological fluids analysis. Sensors Actuators A Phys. 115, 362–367 (2004). [Google Scholar]
  27. Han J. H., Kim D.-H. & Choi K. C. Microcavity effect using nanoparticles to enhance the efficiency of organic light-emitting diodes. Opt. Express 23, 19863 (2015). [DOI] [PubMed] [Google Scholar]
  28. Diest K., Dionne J. a., Spain M. & Atwater H. a. Tunable color filters based on metal-insulator-metal resonators. Nano Lett. 9, 2579–2583 (2009). [DOI] [PubMed] [Google Scholar]
  29. Kim D.-Y., Han Y. C., Kim H. C., Jeong E. G. & Choi K. C. Highly Transparent and Flexible Organic Light-Emitting Diodes with Structure Optimized for Anode/Cathode Multilayer Electrodes. Adv. Funct. Mater. 25, 7145–7153 (2015). [Google Scholar]
  30. Born M. Principles of Optics: Electromagnitic Theory of Propagation, Interference and Diffraction of Light. (Cambridge University Press, 2002).
  31. Lee S.-M., Choi C. S., Choi K. C. & Lee H.-C. Low resistive transparent and flexible ZnO/Ag/ZnO/Ag/WO3 electrode for organic light-emitting diodes. Org. Electron. 13, 1654–1659 (2012). [Google Scholar]
  32. Han H., Theodore N. D. & Alford T. L. Improved conductivity and mechanism of carrier transport in zinc oxide with embedded silver layer. J. Appl. Phys. 103, 13708 (2008). [Google Scholar]
  33. Tao C. et al. Role of tungsten oxide in inverted polymer solar cells. Appl. Phys. Lett. 94, 043311 (2009). [Google Scholar]
  34. Lin J. et al. Understanding the photoelectrochemical properties of a reduced graphene oxide–WO3 heterojunction photoanode for efficient solar-light-driven overall water splitting. Rsc Adv. 3, 9330 (2013). [Google Scholar]
  35. Lee S.-M., Cho Y., Kim D.-Y., Chae J.-S. & Choi K. C. Enhanced Light Extraction from Mechanically Flexible, Nanostructured Organic Light-Emitting Diodes with Plasmonic Nanomesh Electrodes. Adv. Opt. Mater. 3, 1240–1247 (2015). [Google Scholar]
  36. Yang D. Y., Lee S.-M., Jang W. J. & Choi K. C. Flexible organic light-emitting diodes with ZnS/Ag/ZnO/Ag/WO3 multilayer electrode as a transparent anode. Org. Electron. 15, 2468–2475 (2014). [Google Scholar]
  37. Suo Z., Ma E. Y., Gleskova H. & Wagner S. Mechanics of rollable and foldable film-on-foil electronics. Appl. Phys. Lett. 74, 1177–1179 (1999). [Google Scholar]
  38. Shackelford J. F. Introduction to Materials Science for Engineers, 7th Edition. (Pearson, 2009). [Google Scholar]

Associated Data

This section collects any data citations, data availability statements, or supplementary materials included in this article.

Supplementary Materials

Supplementary Information
srep29341-s1.pdf (1.2MB, pdf)
Supplementary Movie S1
Download video file (1,019.1KB, avi)
Supplementary Movie S2
Download video file (2.1MB, avi)

Articles from Scientific Reports are provided here courtesy of Nature Publishing Group

RESOURCES