Skip to main content
PMC home page
Scientific Reports logoLink to Scientific Reports
. 2016 Aug 31;6:32312. doi: 10.1038/srep32312

Achieving ultranarrow graphene perfect absorbers by exciting guided-mode resonance of one-dimensional photonic crystals

Yongbing Long 1,a, Liang Shen 2, Haitao Xu 1, Haidong Deng 1, Yuanxing Li 3
PMCID: PMC5006081  PMID: 27577721

Abstract

Graphene perfect absorbers with ultranarrow bandwidth are numerically proposed by employing a subwavelength dielectric grating to excite the guided-mode resonance of one-dimensional photonic crystals (1DPCs). Critical coupling of the guided-mode resonance of 1DPCs to graphene can produce perfect absorption with a ultranarrow bandwidth of 0.03 nm. The quality factor of the absorption peak reaches a ultrahigh value of 20000. It is also found that the resonant absorption peaks can be tuned by controlling the dispersion line of the guided mode and the period of the grating. When the parameters of the grating and the 1DPCs are suitably set, the perfect absorption peaks can be tuned to any randomly chosen wavelength in the visible wavelength range.

Graphene, a one-atom thick and two-dimensional material, has attracted increasing attention due to its remarkable electronic, mechanical and optical properties1,2. This material also has great potential to be applied to optoelectronic devices such as photodetectors, biosensing, optical modulators, and photovoltaic cells1,2,3,4,5,6,7,8,9,10. However, in the visible and near-infrared range, graphene only absorbs about 2.3% of the light at normal incidence, which is a severe limitation to its further application in optoelectronic devices. Tremendous research efforts have been made to improve light absorption in graphene and various methods have been presented to enhance the light-graphene interaction by improving the optical electric field around the graphene11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28. For example, Fabry-Perot microcavity is constructed by integrating graphene between two mirrors16,17. The microcavity can confine large optical electric field when it resonates and then significantly improve light absorption in graphene; but the enhanced optical absorption cannot be conveniently used for application in biosensing where graphene is required to interact with the surrounding environment. In other studies, plasmonic nanostructures such as metal nanogratings and nanoparticles have been constructed for the same purpose, but light absorption is still low and the bandwidth of the absorption peaks is broad due to the optical loss of the metal18,19,20,21,22,23,24.

More recently, hole-array photonic crystal slab and slit-array dielectric grating are employed to enhance graphene absorption25,26,27. The hole-array/slit-array can diffract the incident light into evanescent electromagnetic waves and then excite the guided-mode resonance within the photonic crystal slab/dielectric grating. Critical coupling of these guided-mode resonances to graphene can improve light absorption in a single graphene or graphene strips up to 100%. The hole-array photonic crystal slab and the slit-array dielectric grating, therefore, are considered a good option to achieve perfect absorption peaks within the visible and near-infrared region. The bandwidth of the perfect absorption peaks, however, remains above several nanometers and the quality factor (Q-factor) of these absorption peaks is still relatively low (only several hundreds).

This paper aims to propose a new type of graphene perfect absorbers (GPAs) with ultrahigh Q-factor and ultranarrow bandwidth by exciting the guided-mode resonance of one-dimensional photonic crystals (1DPCs). For this purpose, a subwavelength dielectric grating is capped on the 1DPCs to excite the guided-mode resonances. As 1DPCs are multilayers with low and high refractive index distributed periodically, the guided mode of this type of multilayers is then modulated by the periodic distribution of refractive index29,30,31. When this type of guided mode of 1DPCs is excited by the grating, it is dually modulated by the periodic distribution of refractive index in the 1DPCs and the periodicity of the dielectric grating. Critical coupling of this dually modulated guided-mode resonance to graphene produces perfect absorption with a ultranarrow bandwidth of 0.03 nm, a value about two orders of magnitude lower than that of the GPAs presented in previous research25,26,27. Correspondingly, the Q-factor of the absorption peak reaches a much higher value of 20000.

Results and Discussions

Achieving GPAs by exciting dually modulated guided-mode resonance of 1DPCs

The proposed GPAs have a structure of graphene strip array/subwavelength TiO2 grating/1DPCs, as is shown in Fig. 1(a). The 1DPCs are assumed to be composed of 10 pairs of (SiO2/TiO2) and the subwavelength TiO2 grating is placed on 1DPCs to excite the guided mode of the 1DPCs. The thickness, period and strip width of the subwavelength gratings are h, p and w, respectively. Finite element method is employed to calculate the optical electric field and the light absorption spectrum for the graphene32,33. More details concerning the calculation can be found in the part Method. In the calculation, the refractive index of TiO2 and SiO2 are assumed to be 2.5 and 1.5. The graphene is assumed to be 0.34 nm and the refractive index is estimated to be n = 3.0 + iC1λ/3 with C1 = 5.446 μm−1 34.

Figure 1. Structure of the device used to achieve perfect absorption.

Figure 1

Open in a new tab

p, w and h respectively denote period, strip width and thickness of the subwavelength grating.

To obtain GPAs, light absorption in graphene strips is optimized by tailoring the thickness, period and strip width of the grating. For this purpose, Monte Carlo method is first used to calculate light absorption in graphene strips by randomly selecting the parameters (h, p and w) of the grating in a broad range. With this method, a series of parameters are obtained for the devices within which light absorption in graphene shows relatively high values. These parameters are then used as initial values to optimize the device structure by calculating light absorption of graphene as a function of h, p and w.

In the calculation, the wavelength of the incident light is randomly set as 600 nm and the polarization is assumed to be transverse magnetic. The center wavelength (λ0) of the photonic bandgap of 1DPCs is set as 600 nm and the reflectance of 1DPCs is 100% at this wavelength. Correspondingly, the thickness of TiO2 and SiO2 layers in 1DPCs is calculated by λ0/4n with n as the refractive index of TiO2 or SiO2. After careful optimization, light absorption in the graphene strips is maximized when w, p and h of the grating are respectively set as 365.0 nm, 197.4 nm and 124.1 nm. The device with these parameters is named as Device I and the calculated absorption spectrum of the device is shown in Fig. 2. From the figure, two main points can be observed. First, the absorption spectrum shows five peaks at the wavelength of 635.7 nm, 627.6 nm, 615.1 nm, 600 nm and 584.7 nm. These peaks are named as Peak i (i = 1, 2, 3, 4, 5), as is shown in Fig. 2(a). Second, absorption at the wavelength of 600 nm (Peak 4) reaches 100%, indicating perfect absorption in the graphene strips is achieved (see Fig. 2(b)).

Figure 2.

Figure 2

Open in a new tab

(a) Absorption spectrum of graphene strips in Device I; (b) Amplification of the absorption spectrum around 600 nm. The red dashed line in (b) denotes the reflection spectrum of Device I.

The multi-peaking absorption spectrum and the perfect absorption in graphene strips are attributed to the excitation of the guided-mode resonance of the 1DPCs. This is examined by calculating the dispersion diagram of 1DPCs and the dispersion line of the guided mode of 1DPCs29,30,31. The dispersion line of the guided mode is determined by using a prism to excite the guided mode of 1DPCs and more details can be found in Supplementary Information. The calculated results are shown in Fig. 3, where line Mi (i = 1, 2, 3, 4, 5) denotes the first-order to the fifth-order guided mode of the 1DPCs. To reveal the relation between the guided mode and the absorption peaks, we superpose the reciprocal lattice vector of the grating (g) and frequency of the absorption peaks (fi, i = 1, 2, 3, 4, 5) onto the dispersion diagram. It is found that the points (g, fi) related to the absorption Peak i are well matched with the dispersion line Mi of the guided mode. This indicates the excitation condition of the guided mode is fulfilled29,30,31:

Figure 3. Dispersion diagram of 1DPCs.

Figure 3

Open in a new tab

The line Mi (i = 1, 2, 3, 4, 5) denotes the ith-order dispersion line of the guided mode of 1DPCs. Points with different colors correspond to Peak i on the absorption spectrum of Device I. The red line denotes the light curve.

graphic file with name srep32312-m1.jpg

where Inline graphic denotes the wavevector of the guided mode of the 1DPCs; Inline graphic denotes the reciprocal lattice vector of the grating and g is calculated by g = 2π/p where p is the period of the grating; m is the grating diffraction order and m is equal to 1 in this paper. The matching of Eq. (1) allows the excitation of the guided mode of the 1DPCs, which in turn enhances light absorption in the graphene strips and leads to the peaks on the absorption spectrum. More specifically, Peak 1 to 5 on the absorption spectrum are caused by the first-order to the fifth-order guided mode of the 1DPCs. The judgment is further confirmed by calculating distribution of the optical electric field in Device I and the calculated results are shown in Fig. 4. It is observed that the envelope of the optical electric field shows i (i = 1, 2, 3, 4, 5) maxima at the direction parallel (z-direction) to the incident light. These maxima result from the standing-wave modes in the waveguide created by the 1DPCs29. This finding verifies that the multi-peaking on the absorption spectrum of Device I results from the guided-mode resonance of the 1DPCs.

Figure 4. Distribution of the optical electric field in Device I when the wavelength of the incident light is positioned at absorption Peak i (i = 1, 2, 3, 4, 5).

Figure 4

Open in a new tab

(a): for Peak 1; (b): for Peak 2; (c): for Peak 3; (d): for Peak 4; (e): for Peak 5. |E| is the modulus of optical electric field in the device and |E0| denotes that of the incident light.

Figure 4 also demonstrates that the optical electric field oscillates at both the parallel (z-direction) and perpendicular (x-direction) direction to the incident light. The oscillating behavior at z-direction is attributed to the periodic modulation of the refractive index in the 1DPCs and at x-direction it is caused by the periodicity of the dielectric grating. Due to the dual modulation, the guided mode of 1DPCs resonates at both the parallel (z-direction) and perpendicular (x-direction) direction to the incident light, which significantly improves the optical electric field inside the 1DPCs. The dually modulated guided-mode resonance of the 1DPCs can leak evanescent waves to the interface of grating/air and subsequently improve the light graphene interaction, as is shown in Fig. 4. When the external leakage energy of the guided-mode resonance is equal to the intrinsic loss of graphene strips (i.e., the condition for critical coupling is fulfilled), critical coupling occurs and total absorption of the light is achieved at the wavelength of 600 nm25,26,27.

Tuning the perfect absorption peaks within visible wavelength range

The calculation above demonstrates that absorption peaks appear when the excitation condition of the guided mode is satisfied. It also suggests that the spectral position of the absorption peaks can be tuned by controlling the dispersion line of the guided mode and the period of the grating, as is indicated by Eq. (1). The judgment is examined by calculating the absorption spectrum of Device I with varied structure parameters of 1DPCs and grating. The calculated results are shown in Fig. 5.

Figure 5.

Figure 5

Open in a new tab

(a) Absorption spectra for Device I with varied thickness of the TiO2 layer Inline graphic in the 1DPCs; (b) dispersion line of the 4th-order guided mode of 1DPCs with varied Inline graphic and the squares denote the absorption peaks when Inline graphic is set as varied values. (c) Absorption spectra for Device I with varied period (p) of the grating. (d) dispersion line of the 4th-order guided mode of 1DPCs with Inline graphic set as 60 nm and the squares denote the absorption peaks in graphene strips when period (p) of the grating is set as varied values. The dotted line in (b) and dashed line in (d) denote the reciprocal lattice vector of the grating.

In Fig. 5(a), the spectral position of the absorption peaks is redshifted by a value of 14.8 nm when the TiO2 layer in 1DPCs is increased by 10 nm. This happens because an increase in the thickness of the TiO2 layer can shift the dispersion line of the guided mode to the lower frequency region (see Fig. 5(b)); therefore a lower frequency (i.e., a larger wavelength) is required to match the excitation condition of the guided mode of the 1DPCs. Correspondingly, the absorption peaks are shifted to the longer wavelengths. In Fig. 5(c), an increase of 10 nm in the period of the grating leads to a redshift of 6.2 nm for the absorption peaks. This is because a grating with larger period can excite the guided mode in the longer wavelength range (i.e., guided mode with lower frequency), as is shown in Fig. 5(d). It is also observed in Fig. 5(b,d) that the points (k, f) related to the absorption peaks for the devices with varied thickness of TiO2 layer and period of grating are just positioned on the dispersion lines of the guided mode of the 1DPCs. The finding confirms the conclusion that absorption peaks occur when the excitation condition of the guided mode (i.e., Equation (1)) is matched.

These results demonstrate that absorption peaks are sensitive to the structure parameters of the grating and 1DPCs, and the spectral position of absorption peaks can be tuned by tailoring these parameters. In fact, when the period (p), strip width (w) and thickness (h) of the grating and the parameters of the 1DPCs are properly designed to fulfill the condition for critical coupling between the guided-mode resonance and graphene, perfect absorption can be achieved at any randomly given wavelength within the visible wavelength range. In Fig. 6, for example, perfect absorption occurs at the wavelength of 400 nm when p, w and h are respectively set as 266.3 nm, 107.8 nm and 91.3 nm. When these parameters are tailored to the values of 528.3 nm, 277.8 nm and 157.6 nm, perfect absorption is tuned to the wavelength of 800 nm. In both cases, the thickness of TiO2 and SiO2 layers in 1DPCs is determined by λ0/4n with λ0 as the wavelength of the absorption peaks and n as the refractive index of TiO2 or SiO2. In these calculations, however, refractive index of TiO2 and SiO2 is set as constant values when the wavelength varies from 400 nm to 800 nm. In practical design of GPAs, the realistic material dispersion of the refractive index should be taken into consideration.

Figure 6. Absorption spectra for the device with perfect absorption at 400 nm, 600 nm and 800 nm.

Figure 6

Open in a new tab

Achieving GPA with ultranarrow bandwidth

It is observed in Fig. 2 that absorption peaks related to lower-order guided-mode resonance has narrower bandwidth. In other words, GPAs with narrow bandwidth can be achieved by exciting low orders of the guided-mode resonance of 1DPCs. This is investigated by designing GPAs of which different orders of guided-mode resonance is excited. In the designing process, the wavelength of the incident light is assumed to be 600 nm. The center wavelength of the photonic bandgap of 1DPCs is set as 600 nm, and the thickness of TiO2 and SiO2 layers in 1DPCs is calculated to be 60 nm and 100 nm, respectively. The period of the grating is set as the values which can excite the different orders of the guided mode of the 1DPCs and these values are obtained by Eq. (1). The thickness and strip width of the grating are tailored to fulfill the condition for critical coupling between the guided-mode resonance and graphene. After optimization, it is found that perfect absorption is achieved for all orders of the guided-mode resonances (i = 1, 2, 3, 4, 5), as is shown in Fig. 7.

Figure 7. Absorption spectra for the device when different orders of guided mode are used to achieve perfect absorption at 600 nm.

Figure 7

Open in a new tab

Mi (i = 1, 2, 3, 4, 5) denotes the absorption spectrum related to the ith-order of the guided-mode resonance.

Another important result observed in Fig. 7 is that the bandwidth of the absorption peak related to the first-order guided-mode resonance is as small as 0.03 nn, a value about two order of magnitude narrower than that of the GPAs reported in relevant research so far25,26,27. Due to the small bandwidth, the Q-factor of the resonant peak is calculated to be as high as 20000, about two orders of magnitude higher than that of the GPAs in previous studies. Here the Q-factor is defined by Q = λ/Δλ where λ is the center wavelength of the peak and Δλ represents the bandwidth of the absorption peak. The narrower resonance is achieved because GPAs in this paper result from the excitation of the guide-mode resonance of the 1DPCs while GPAs in previous studies result from the excitation of the guided-mode resonance of either the grating or photonic crystal slab25,26,27. For the latter, the graphene is just positioned neighbouring to the grating or the photonic crystal slab, where guided-mode resonance significantly improves the optical electric field. The leakage rate of the energy from the guided-mode resonance to the graphene is relatively large25. Thus, a guided-mode resonance with low Q-factor (i.e., with less energy stored in 1DPCs) is required to achieve critical coupling and the bandwidth of the absorption peak is rendered relatively large.

But for the GPAs discussed in this paper, graphene is placed far away from the 1DPCs, where large optical electric field is confined by the guide-mode resonance (see Fig. 5). The leakage rate of the energy from the guided-mode resonance to the graphene is relatively low and resonance with high Q-factor (i.e., with more energy stored in 1DPCs) is required to fulfill the critical coupling condition. Hence, narrower absorption peaks can be achieved.

Interestingly, similar results can be also obtained when graphene strips are replaced by an infinitely extended graphene layer. This type of device with infinitely extended graphene on the top of grating backed by 1DPCs is referred to as Device II. Figure 8(a) demonstrates that perfect absorption is achieved for Device II when p,w and h of the grating are respectively set as 343.5 nm, 203.6 nm, 125.0 nm. The total absorption is attributed to the excitation of the first-order guided-mode resonance of 1DPCs. This can be examined by calculating the optical electric field in Device II and the calculated results are shown in Fig. 8(b). It is observed that large optical electric field is confined within the 1DPCs and the envelope of the optical electric field shows one maximum at the direction parallel (z-direction) to the incident light. Figure 8(b) also shows that the guided-mode resonance of 1DPCs leaks evanescent waves to graphene and then improves the light-graphene interaction, which ultimately results in the perfect absorption in the infinitely extended graphene layer.

Figure 8.

Figure 8

Open in a new tab

(a) Absorption spectrum of the infinitely extended graphene layer in Device II. The red dashed line in denotes the reflection spectrum of Device I. (b) Distribution of the optical electric field in Device II. |E| is the modulus of optical electric field in the device and |E0| denotes that of the incident light.

So far, the calculation in this paper has demonstrated that perfect absorption with ultranarrow bandwidth can be achieved at a target wavelength by properly designing the device parameters. This, however, requires sub-nm fabrication precision. Considering current accuracy of fabricating techniques, the practical size of the grating will deviate from the values of the designed parameters to achieve perfect absorption at a target wavelength. As a result, the absorption peaks may be broadened and shifted away from the target wavelength, which renders it very challenging to fabricate the GPAs with ultranarrow absorption peaks at the designated target wavelength. Despite this, the deviation of the absorption peak can be restricted in a controlled wavelength region when the fabricating accuracy is included in the simulation. The physical laws revealed in this paper, we believe, shall shed new lights on finding effective approaches to achieve ultranarrow absorption peaks.

Conclusions

GPAs with ultranarrow bandwidth are presented by using a subwavelength dielectric grating to excite the guided-mode resonance of 1DPCs. By carefully designing the structure parameters of the gratings and the 1DPCs, perfect absorption peaks can be tuned to any randomly chosen wavelength in the visible wavelength range. The bandwidth of the perfect absorption peak reaches a ultrasmall value of 0.03 nm, about two orders of magnitude higher than that of the GPAs reported in previous research. Correspondingly, the Q-factor of the absorption peak reaches a ultrahigh value of 20000. The resonant absorption peak with ultranarrow bandwidth can be considered for application in biosensing and light detection with ultra-high sensitivity.

Method

Optical electric field in the devices is first calculated by employing finite element method29,30. In the calculation, the left and right boundaries of the computational domain are set as periodic boundary conditions; the top and bottom of the computational domain are set as absorbing boundary condition: perfectly matched layers, which are ten wavelengths away from the device. Adaptive triangle meshing with a maximum element size of 0.08 nm has been used in graphene domain. In the grating domain, the maximum element size is set as 1 nm and the minimum element size is set as 0.1 nm. With the optical electric field obtained from finite element method as input parameters, light absorption in graphene is then calculated as Inline graphic, where ε0 is the permittivity of vacuum, λ and I(λ) are respectively the wavelength and intensity of the incident light; n and k denote the refraction index and extinction coefficient of graphene; E(x) is the electrical optical field in graphene32,33,35.

The dispersion line of the guided mode of 1DPCs is determined by the method presented in the supporting information. In this method, a prism is attached to the 1DPCs and reflectance is calculated as a function of the incident angle. The reflectance shows dips when the angle increases. With the incident angle of these dips as input parameters, the wavevector of the guided mode can be calculated and the mode dispersion relations can be obtained. More details can be found in the Supplementary Information.

Additional Information

How to cite this article: Long, Y. et al. Achieving ultranarrow graphene perfect absorbers by exciting guided-mode resonance of one-dimensional photonic crystals. Sci. Rep. 6, 32312; doi: 10.1038/srep32312 (2016).

Supplementary Material

Supplementary Information
srep32312-s1.pdf (321.9KB, pdf)

Acknowledgments

This work is supported by Guangdong Natural Science Funds for Distinguished Young Scholar (Grant No: 2014A030306005), Natural Science Foundation of Guangdong Province, China (Grant Nos 2013010012854, 2016A03031339), Foundation for High-level Talents in Higher Education of Guangdong Province, China (Yue Cai-Jiao [2013]246, Jiang Cai-Jiao[2014]10), Development Program for Outstanding Young Teachers in Guangdong University (Yue Jiaoshi [2014]108). The Science and Technology Program of Guangzhou (No. 201607010176).

Footnotes

Author Contributions Y. Long conceived the idea, performed the calculation and wrote the manuscript, L.S. helped in numerical calculations and discussed the results, H.X. helped in numerical calculations, H.D. helped in numerical calculations and discussed the results, Y. Li helped in numerical calculations. All authors contributed to the manuscript.

References

  1. Novoselov K. S. et al. Electric field effect in atomically thin carbon films. Science 306, 666 (2004). [DOI] [PubMed] [Google Scholar]
  2. Kim K. S. et al. Large-scale pattern growth of graphene films for stretchable transparent electrodes. Nature 457, 706–710 (2009). [DOI] [PubMed] [Google Scholar]
  3. Bonaccorso F. et al. Graphene photonics and optoelectronics. Nat. Photonics 4, 611–622 (2010). [Google Scholar]
  4. García de Abajo F. J. Graphene plasmonics: Challenges and opportunities. ACS Photonics 1, 135–152 (2014). [Google Scholar]
  5. Vakil A. & Engheta N. Transformation, optics using graphene. Science 332, 1291–1294 (2011). [DOI] [PubMed] [Google Scholar]
  6. Fan Y. et al. Tunable mid-infrared coherent perfect absorption in a graphene meta-surface. Sci. Rep. 5, 13956 (2015). [DOI] [PMC free article] [PubMed] [Google Scholar]
  7. Xia F. et al. Two-dimensional material nanophotonics. Nat. Photonics 8, 899 (2014). [Google Scholar]
  8. Alaee R., Farhat M., Rockstuhl C. & Lederer F. A perfect absorber made of a graphene micro-ribbon metamaterial. Optics Express 20, 28017–28024 (2012). [DOI] [PubMed] [Google Scholar]
  9. Yu R., Pruneri V. & García de Abajo F. Resonant Visible Light Modulation with Graphene. ACS Photonics 2, 550–558 (2015). [Google Scholar]
  10. Yu R., Alaee R., Lederer F. & Rockstuhl C. Manipulating the interaction between localized and delocalized surface plasmon-polaritons in graphene. Phys. Rev. B 90, 085409 (2014). [Google Scholar]
  11. Pirruccio G., Martin Moreno L., Lozano G. & Gomez Rivas J. Coherent and Broadband Enhanced Optical Absorption in Graphene. ACS Nano 7, 4810–4817 (2013). [DOI] [PubMed] [Google Scholar]
  12. Xiang Y. et al. Critical coupling with graphene-based hyperbolic metamaterials. Sci. Rep. 4, 5483 (2014). [DOI] [PMC free article] [PubMed] [Google Scholar]
  13. Fang Z. et al. Active Tunable Absorption Enhancement with Graphene Nanodisk Arrays. Nano Letters 14, 299–304 (2014). [DOI] [PubMed] [Google Scholar]
  14. Zhao W., Shi K. & Lu Z. Greatly enhanced ultrabroadband light absorption by monolayer graphene. Opt. Lett 38, 4342–4345 (2013). [DOI] [PubMed] [Google Scholar]
  15. Thongrattanasiri S. et al. Complete Optical Absorption in Periodically Patterned Graphene. Phys. Rev. Lett 108, 047401 (2012). [DOI] [PubMed] [Google Scholar]
  16. Furchi M. et al. Microcavity-Integrated Graphene Photodetector. Nano Letters 12, 2773–2777 (2012). [DOI] [PMC free article] [PubMed] [Google Scholar]
  17. Ferreira A. et al. Graphene-based photodetector with two cavities. Phys. Rev. B 85, 115438 (2012). [Google Scholar]
  18. Zhao B. et al. Strong Plasmonic Coupling between Graphene Ribbon Array and Metal Gratings. ACS Photonics 2, 1611–1618 (2015). [Google Scholar]
  19. Zhu X. et al. Enhanced Light–Matter Interactions in Graphene-Covered Gold Nanovoid Arrays. Nano Letters 13, 4690–4696 (2013). [DOI] [PubMed] [Google Scholar]
  20. Cai Y., Zhu J. & Liu Q. H. Tunable enhanced optical absorption of graphene using plasmonic perfect Absorbers. Appl. Phys. Lett. 106, 043105 (2015). [Google Scholar]
  21. Song S., Chen Q., Jin L. & Sun F. Great light absorption enhancement in a graphene photodetector integrated with a metamaterial perfect absorber. Nanoscale 5, 9615 (2013). [DOI] [PubMed] [Google Scholar]
  22. Zhao B., Zhao J. M. & Zhang Z. M. Enhancement of near-infrared absorption in graphene with metal gratings. Appl. Phys. Lett. 105, 031905 (2014). [Google Scholar]
  23. Hashemi M., Farzad M. H., Mortensen N. A. & Xiao S. Enhanced absorption of graphene in the visible region by use of plasmonic nanostructures. J. Opt. 15, 055003 (2013). [Google Scholar]
  24. Grande M. et al. Fabrication of doubly resonant plasmonic nanopatch arrays on graphene. Applied Physics Letters 102, 231111 (2013). [Google Scholar]
  25. Piper J. R. & Fan S. H. Total Absorption in a Graphene Monolayer in the Optical Regime by Critical Coupling with a Photonic Crystal Guided Resonance. ACS Photonics 347 (2014) [Google Scholar]
  26. Hu J. H. et al. Enhanced absorption of graphene strips with a multilayer subwavelength grating structure. Appl. Phys. Lett. 105(22), 221113 (2014). [Google Scholar]
  27. Grande M. et al. Graphene-based perfect optical absorbers harnessing guided-mode resonances. Opt. Express 23, 21032 (2015). [DOI] [PubMed] [Google Scholar]
  28. Zhang M. & Zhang X. Ultrasensitive optical absorption in graphene based on bound states in the continuum. Sci. Rep. 5, 8266 (2015). [DOI] [PMC free article] [PubMed] [Google Scholar]
  29. Robertsona W. M. & May M. S. Surface electromagnetic wave excitation on one-dimensional photonic band-gap arrays. Appl. Phys. Lett. 74, 29 (1999). [Google Scholar]
  30. Liscidin M. & Sipe J. E. Analysis of Bloch-surface-wave assisted diffraction-based biosensors. J. Opt. Soc. Am. B 26, 279 (2009). [Google Scholar]
  31. Chen Y. et al. Study on the propagation mechanism of evanescent waves in one-dimensional periodic photonic crystal. Physics Letters A 379, 2257–2260 (2015). [Google Scholar]
  32. Long Y. B., Li Y. X. & Su R. M. Simultaneously improving optical absorption of both transverse-electric polarized and transverse-magnetic polarized light for organic solar cells with Ag grating used as transparent electrode. AIP Advances 4, 087143 (2014). [Google Scholar]
  33. Volakis J., Chatterjee A. & Kempel L. Finite Element Method Electromagnetics: Antennas, Microwave Circuits, and Scattering Applications (Wiley-IEEE Press, 1998). [Google Scholar]
  34. Bruna M. & Borini S. Optical constants of graphene layers in the visible range. Appl. Phys. Lett. 94, 031901 (2009). [Google Scholar]
  35. Long Y. Effects of metal electrode reflection and layer thicknesses on the performance of inverted organic solar cells. Sol. Energy Mater. Sol. Cells 94, 744–749 (2010). [Google Scholar]

Associated Data

This section collects any data citations, data availability statements, or supplementary materials included in this article.

Supplementary Materials

Supplementary Information
srep32312-s1.pdf (321.9KB, pdf)

Articles from Scientific Reports are provided here courtesy of Nature Publishing Group

RESOURCES