Skip to main content
PMC home page
Scientific Reports logoLink to Scientific Reports
. 2016 Dec 12;6:38859. doi: 10.1038/srep38859

Creation of Sub-diffraction Longitudinally Polarized Spot by Focusing Radially Polarized Light with Binary Phase Lens

An-ping Yu 1,*, Gang Chen 1,a,*, Zhi-hai Zhang 1,*, Zhong-quan Wen 1,b,*, Lu-ru Dai 2,c,*, Kun Zhang 1,2,*, Sen-lin Jiang 1, Zhi-xiang Wu 1, Yu-yan Li 1, Chang-tao Wang 3, Xian-gang Luo 3
PMCID: PMC5150649  PMID: 27941852

Abstract

The generation of a sub-diffraction longitudinally polarized spot is of great interest in various applications, such as optical tweezers, super-resolution microscopy, high-resolution Raman spectroscopy, and high-density optical data storage. Many theoretical investigations have been conducted into the tight focusing of a longitudinally polarized spot with high-numerical-aperture aplanatic lenses in combination with optical filters. Optical super-oscillation provides a new approach to focusing light beyond the diffraction limit. Here, we propose a planar binary phase lens and experimentally demonstrate the generation of a longitudinally polarized sub-diffraction focal spot by focusing radially polarized light. The lens has a numerical aperture of 0.93 and a long focal length of 200λ for wavelength λ = 632.8 nm, and the generated focal spot has a full-width-at-half-maximum of about 0.456λ, which is smaller than the diffraction limit, 0.54λ. A 5λ-long longitudinally polarized optical needle with sub-diffraction size is also observed near the designed focal point.

There is a growing interest in tight focusing of radially polarized light, due to its unique property of a strong longitudinal and nonpropagating electric field in the focal region. In the focal spot, compared with the radial polarization component, the longitudinal electrical field is dominant and makes no contribution to the energy flow along the optical axis, which is important in metallic particle trapping1, particle acceleration2, and tip-enhanced Raman spectroscopy3. Furthermore, theoretical works have predicted that focusing radially polarized light can create a longitudinal electric field component with a smaller focal spot size than linearly polarized and circularly polarized beams. This property is of great importance in applications such as microscopes4,5 and optical data storage6. Generation of a sub-wavelength focal spot with a strong longitudinal electric field has been theoretically proposed using various methods, such as use of a parabolic mirror7, the combination of a binary optical phase filter and a conventional high-numerical-aperture optical lens8,9,10,11,12, a negative-index grating lens13, a 4π high-numerical-aperture focusing system14, and absorbance modulation15. Compared with conventional optical lenses, planar lenses are attractive because they are small, lightweight, and easily integrated. Theoretical investigations have been conducted into the tight focusing of radially polarized light using a planar plasmonic metalens based on the parabolic phase profile16, and the resulting focal spot size was still diffraction-limited. Although super-resolution can be achieved by near-field optics17,18, super-oscillation provides a promising approach to realize far-field sub-diffraction focusing and imaging. Many planar diffractive lenses have been proposed for focusing and imaging beyond the diffraction limit19,20,21,22,23,24,25,26,27. Although metasurfaces26,28 have been reported for focusing purposes, their amplitude transmission rate is very low and they are difficult to be fabricated in visible wavelength range. Recently, super-oscillation planar lenses based on quasi-continuous amplitude modulation29,30 and a binary amplitude-phase mask31 have been demonstrated for sub-diffraction focusing of linearly polarized light. A binary amplitude-phase-mask-based super-oscillation lens was reported for the super-oscillatory focusing of circularly polarized waves with an ultra-long focal length and small numerical aperture (NA)32. For this paper, we experimentally demonstrated the generation of a sub-diffraction longitudinally polarized spot by focusing radially polarized light with a planar binary phase lens.

Materials and Methods

Binary phase lens design

The radially polarized wave can be generated by an s-wave plate, which converts a linearly polarized Gaussian beam into a radially polarized beam in the Laguerre-Gaussian profile. The resulting electrical field can be described by equation 1, where E0 is the incident electrical field amplitude, w0 is the beam waist size, z0 = πw02/λ is the Rayleigh range, R(z) = z[1 + (z0/z)2] is the radius of curvature, w(z) = w0[1 + (z/z0)2]1/2 is the beam width at z, and k = 2π/λ is the wavenumber.

graphic file with name srep38859-m1.jpg

According to the vectorial angular spectrum theory23, for a radially polarized wave impinging on a circularly symmetrical planar lens, its diffracted electrical field on the focal plane at z = zf can be expressed by equations (2) in cylindrical coordinate, where Er, Eφ, and Ez are the radial, azimuthal, and longitudinal polarization components of the diffracted electrical field, respectively; r and ρ are radial coordinates in the spatial and frequency domains, respectively; g(r) = Er(r, zl) is the complex amplitude distribution of the radially polarized electrical field on the lens input surface, zl being the position of the lens input surface; t(r) is the complex amplitude transmittance function of the lens; J0 and J1 are the zero- and first-order Bessel functions, respectively; and q(ρ) = (1/λ2−ρ2)1/2 is the frequency component in the propagation direction. According to the equations, it is clear that, besides the radial polarization electrical component, the diffracted electrical field also includes a longitudinal polarization, which plays a key role in the focusing, as shown later. Notice also that the azimuthal polarization is zero.

graphic file with name srep38859-m2.jpg

To design the binary phase lens, the incident radially polarized light was first produced by illuminating an s-wave plate (Workshop of Photonics, Lithuania) with a normal incident linearly polarized Gaussian beam at a wavelength of 632.8 nm from a He-Ne laser. The resulting doughnut-shaped intensity profile was taken with a CCD camera, as shown in Fig. 1(a), which illustrates a Laguerre–Gaussian hollow ring structure with w0 = 331 μm and z = 276 mm. The corresponding phase distribution was deduced using equation 1, by fitting the amplitudes and phases of electrical fields on two measured planes perpendicular to the optical axis. Figure 2(b) gives the corresponding optical intensity and phase distribution along the radial direction, which shows a peak-peak diameter of 820λ and a hollow ring full width at half maximum (FWHM) of 412λ.

Figure 1.

Figure 1

Open in a new tab

(a) The color map of the azimuthally polarized light intensity distribution on the lens incident surface; (b) the corresponding optical intensity and phase distribution in the radial direction.

Figure 2.

Figure 2

Open in a new tab

(a) The optimized phase distribution of the lens; (b) the intensity (red) and phase (blue) distribution of the longitudinal electrical component, and the intensity (pink) and phase (green) distribution of the radial electrical component on the focal plane. The inset plots the total optical intensity on the focal plane at z = 200λ.

According to the obtained electrical field distribution, a binary phase lens consisting of concentric rings was optimized for a normally incident radially polarized wave at wavelength λ = 632.8 nm, by utilizing the genetic algorithm33 and the vectorial angular spectrum formulas given in equations (2). The radius of the lens is R = 500λ, its focal length is f = 200λ, and its NA is sin[arctan(f/R)] = 0.93. The lens diffraction limit (0.5λ/NA) and super-oscillation criterion (0.38λ/NA)34 are 0.54λ and 0.41λ respectively. The width of the ring is an integer multiple of T = 500 nm. The focal spot was designed with FWHM of 240 nm (0.38λ), which is smaller than the diffraction limit of 0.54λ and the super-oscillation criterion of 0.41λ. Figure 2(a) gives the optimized phase spatial distribution on the planar lens, and its inset shows a zoom-in plot of the phase distribution. The details of the phase distribution can be found in the supplement. The theoretically optimized electrical field distribution on the focal plane is depicted for Er and Ez, respectively, with respect to the radial coordinate, in Fig. 2(b). As expected, the longitudinal component Ez makes the major contribution to the formation of the focal spot, and its peak intensity is about 74 times greater than the maximum intensity of the radial component Er. Sharp phase inversion was observed at those points where the intensity of each electrical component was zero, which is the unique property of a super-oscillatory electrical field. The sidelobe intensity on the focal plane was found to be less than 20% of the central lobe peak intensity, resulting in a very clear field of view in the area of concern of [−700λ, +700λ], as depicted in the inset of Fig. 2(b).

Numerical simulation of the longitudinally polarized spot generation

To realize the binary phase lens, concentric dielectric ring layers were employed to achieve the desired phase distribution. Figure 3(a) shows the working principle of the lens. As shown in Fig. 3(b), the binary lens consists of a series of concentric Si3N4 rings grown on the top of a glass substrate. The thickness and the minimum width of the rings are t and T, respectively. The binary phase of 0 and π was achieved by controlling the thickness of the Si3N4 layer t, which is determined by t = φλ/2π(nSi3N4−1), where φ corresponds to the desired phase value of 0 or π, and nSi3N4 is the refractive index of Si3N4.

Figure 3.

Figure 3

Open in a new tab

(a) Generation of a sub-diffraction longitudinal spot by focusing the radially polarized wave with a planar binary phase lens; (b) the micro lens structure; (c) the micro lens physical model for COMSOL numerical simulation.

Numerical simulation was conducted for a dielectric ring binary phase lens based on the phase distribution described in Fig. 2(a), using COMSOL Multiphysics software. Utilizing the circular symmetry of the radially polarized incident wave and the lens, the 3-dimentional model can be simplified into a 2-dimentional model. As shown in Fig. 3(c), a 2-dimentional model was constructed in the positive half XZ plane (X > 0), which consists of ring structures obtained during lens design (as presented in the supplementary materials). In the physical model, the refractive index of Si3N4 is set at 1.91, and therefore the thicknesses corresponding to phase 0 and π are t = 0 and 348 nm, respectively. In the simulation, scattering boundary condition and perfectly matched layer was used to avoid unphysical reflection by the boundary. Figure 4(a) plots the peak intensity (red), spot transverse FWHM (blue), and sidelobe ratio (green) (the ratio of the maximum sidelobe intensity to the central lobe intensity) along the optical axis near the designed focal point at z = 200λ. As illustrated by the red curve, there is a double-hump-shaped spot with a longitudinal FWHM of FWHMz = 5λ in the propagation direction. The two humps are located at z = 198.9λ and 201.6λ on the optical axis. The intensity at the valley is only 41% of the spot peak intensity. It is interesting to find that this valley point is located at z = 200.3λ and has the minimum transverse FWHM of 0.39λ, which are close to the designed focal length of 200λ and FWHM of 0.38, respectively. In the small region of [200λ, 200.6λ] around the focal point z = 200.3λ, the transverse FWHM is below the super-oscillatory criterion. According to the blue curve, in the area of [197.8λ, 202.8λ] in the propagation direction, as indicated by the arrows, the transverse FWHM of the spot is less than the diffraction limit, resulting in a sub-diffraction longitudinally polarized optical needle with a length of 5λ. It was found that, as shown in the green curve, the transverse sidelobe ratio of the whole focal spot in the area of [197.8λ, 202.8λ] is less than 25.8%. The total optical intensity and optical intensity of each electrical component at z = 200.3λ are plotted in Fig. 4(b). As expected, the azimuth polarization (red) is zero, and the radial polarization has intensity 64 times smaller than that of the longitudinal polarization, similar to above design. The inset of Fig. 3(b) depicts the normalized intensity distribution on the focal plane at z = 200.3λ, which shows a clear field of view within the radius of 500λ, agreeing with the theoretical design.

Figure 4. COMSOL numerical simulation results.

Figure 4

Open in a new tab

(a) the spot FWHM (blue), sidelobe ratio (green), and intensity (red) distribution on the optical axis near the focal point, where the black dashed line and red dashed line indicate the diffraction limit and super-oscillatory criterion, respectively; (b) the total optical intensity (pink), and the intensities of radial (black), azimuthal (red) and longitudinal (blue) components on the focal plane at z = 200.4λ.

Binary phase lens fabrication

Following the above design, a binary phase lens was fabricated on a 500-μm-thick sapphire substrate using electron-beam lithography and dry etching. The Si3N4 layer was first deposited on the substrate by plasma-enhanced chemical vapor deposition, and the Si3N4 layer was measured by an ellipsometry, which gave a refractive index of 1.91. The dielectric layer thickness was about 348 nm, corresponding to the relative phase change of π. Figure 5 shows the SEM images of the lens.

Figure 5. SEM images of the microlens based on binary phase mask.

Figure 5

Open in a new tab

Experimental methods

To experimentally generate the sub-diffraction longitudinally polarized spot, a radially polarized light was first produced with a linearly polarized Gaussian beam at a wavelength of 632.8 nm by an s-wave plate (Workshop of Photonics, Lithuania). The beam profile is presented in Fig. 1. The power of the generated radially polarized light is about 1.4 mW. In the experiment, the radially polarized wave normally illuminated on the lens from the substrate side. The diffracted optical intensity distribution behind the lens was obtained with a tapered optical fiber probe (CFN-100 from Nanonics Imaging, Ltd., Israel) mounted on a 3-D piezo nanopositioner (P-561.3CD from Physik Instrumente GmbH & Co., Germany). The probe tip diameter was about 100 nm. The spatial resolution and scanning range of the nanopositioner were about 10 nm and 100 μm, respectively, for each of the x-, y-, and z-axes. The collected photons were counted with a single photon detector (SPCM50A/M from Thorlabs, Inc., USA).

Results and Discussion

Figure 6(a) illustrates the in-plane optical intensity distribution at z = 201.4λ; except for a single weak spot near the central focal point, no large sidelobe was found in the 10 μm × 10 μm scanned square area. In Fig. 6(b), the beam transverse profiles are plotted against the x-axis (blue) and y-axis (green), respectively, and the numerical simulation result (red) is also depicted for comparison. It was found that the FWHM is 331 nm and 251 nm in the x-axis and y-axis, respectively. The FWHM in the y-axis is smaller than the super-oscillatory criterion of 259 nm, and is close to the designed value of 240 nm, while the FWHM in the x-axis is larger than the super-oscillatory criterion, but still smaller than the diffraction limit of 341 nm. For a better evaluation of the spot size, we measured the FWHM across the spot center in different directions, as plotted in Fig. 6(c). All the FWHM values are smaller than the diffraction limit, and four of them are below the super-oscillatory criterion. The average FWHM is 289 nm. This asymmetry is believed to be caused by errors in the alignment of the three optical axes of the laser beam, s-wave plate and testing sample in the experiment.

Figure 6.

Figure 6

Open in a new tab

(a) Color map of the focal plane intensity distribution; (b) intensity distribution along the x-axis (green) and y-axis (blue), where the numerical simulation result of the optical intensity (red) is also depicted for comparison; (c) the focal spot FWHM in different directions, where the y-axis value is the angle between the direction and the positive y-axis, and the dashed and dotted lines denote the diffraction limit (341 nm) and super-oscillation criterion (259 nm) of the lens, respectively.

Figure 7(a) illustrates the experimentally obtained optical intensity distribution in the y-z plane near the designed focal spot position. Along the optical axis, two connected focal spots were found, corresponding to the double humps located at z = 198.9λ and 201.6λ, as shown in Fig. 4(a). For comparison, the optical intensity in the same area obtained by COMSOL numerical simulation is plotted in Fig. 7(b), which shows good similarity to the experimental result. The optical intensity along the optical axis is plotted in Fig. 7(c); the COMSOL numerical simulation of the y-z plane optical intensity (red curve) is also plotted, and is similar to the experimental data (red circles). The average transverse FWHM is also plotted for experimental (blue squares) and numerical simulation (blue curve) respectively. In range from z = 197.4λ to 203.2λ, the average FWHM is less than the diffraction limit 0.54λ, resulting in a 5λ-long sub-diffraction optical needle with longitudinal polarization. Although sub-diffraction optical needles with linear polarization35 and circular polarizaiton20,24 have been experimentally demonstrated previously, the optical needle reported here has a unique longitudinally polarization along the optical axis.

Figure 7. Color maps of the optical intensity on the y-z plane near the focal point.

Figure 7

Open in a new tab

(a) the experimental result; (b) the numerical simulation; (c) optical intensities on the optical axis (z-axis) near the focal point: numerical simulation (red curve) and experimental result (red circles); and the transverse FWHM on the optical axis near the focal point: numerical simulation (blue curve) and experimental result (blue squares).

Conclusions

In conclusion, we have proposed and experimentally demonstrated the generation of a sub-diffraction longitudinally polarized spot by focusing a radially polarized light using a binary phase lens. This lens has a long focal length of about 200λ and NA of 0.93. The designed focal spot has an FWHM of 240 nm, which is below the super-oscillatory criterion of 0.41λ. The experimental results show a focal spot with average FWHM of about 289 nm, smaller than the diffraction limit of 342 nm. The spot longitudinal size is about 5λ in the propagation direction, leading to a sub-diffraction optical needle with longitudinal polarization. Although high-NA conventional lenses have been suggested to generate longitudinally polarized light, here we see that they can also be created theoretically and experimentally by using a pure binary phase lens alone. Not only is the sub-diffraction longitudinally polarized needle important for super-resolution microscopy, but it might also find its applications in optical tweezers, Raman spectroscopy, and optical data storage. This approach is also applicable to other optical spectrum ranges. A combination of focusing and polarization conversion in a single phase lens is expected to further reduce the size of a longitudinally polarized spot in the experiment, for less difficulty in optical alignment.

Additional Information

How to cite this article: Yu, A.- et al. Creation of Sub-diffraction Longitudinally Polarized Spot by Focusing Radially Polarized Light with Binary Phase Lens. Sci. Rep. 6, 38859; doi: 10.1038/srep38859 (2016).

Publisher's note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Supplementary Material

Supplementary Information
srep38859-s1.doc (363.5KB, doc)

Acknowledgments

The authors would like to acknowledge the financial support from the China National Key Basic Research and Development Program under Grant No. 2013CBA01700. This work was also supported by the China National Natural Science Foundation under Grant Nos 61575031 and 61177093, the Program for New Century Excellent Talent in University (NCET-13-0629), the Scientific Research Foundation for the Returned Overseas Chinese Scholars, State Education Ministry, the Fundamental Research Funds for the Central Universities (projects 106112013CDJZR120019, 106112016CDJZR125503 and 106112015CDJXY120012), and Chongqing advanced and applied basic research project(cstc2015jcyjA40020). Authors also thank LetPub (www.letpub.com) for their linguistic assistance during the preparation of this manuscript.

Footnotes

Author Contributions G.C. conceived the idea and carried out the lens design. A.P.Y. performed the numerical simulations. K.Z. fabricated the lens samples. S.L.J. and L.R.D. helped in fabricating lens samples. G.C., Z.Z.Z., L.R.D. and Z.Q.W. designed and built up the experimental system. A.P.Y., Z.X.W. and Y.Y.L. conducted the experiment. A.P.Y. and G.C. analyzed the data. C.T.W. and X.G.L. gave helpful suggestions in the design. G.C. prepared the manuscript.

References

  1. Zhan Q. Trapping metallic Rayleigh particles with radial polarization. Optics Exp. 12, 3377–3382 (2004). [DOI] [PubMed] [Google Scholar]
  2. Gupta D. N., Kant N., Kim D. E. & Suk H. Electron acceleration to GeV energy by a radially polarized laser. Phys. Lett. A. 368, 402–407 (2007). [Google Scholar]
  3. Hayazawa N., Saito Y. & Kawata S. Detection and characterization of longitudinal field for tip-enhanced Raman spectroscopy. Appl. Phys. Lett. 85, 6239–6241 (2004). [Google Scholar]
  4. Yoshiki K., Ryosuke K., Hashimoto M., Hashimoto N. & Araki T. Second-harmonic-generation microscope using eight-segment polarization-mode converter to observe three-dimensional molecular orientation. Optics. Lett. 32, 1680–1682 (2007). [DOI] [PubMed] [Google Scholar]
  5. Terakado G., Watanabe K. & Kano H. Scanning confocal total internal reflection fluorescence microscopy by using radial polarization in the illumination system. Appl. Opt. 48, 1114–1118 (2009). [DOI] [PubMed] [Google Scholar]
  6. Kim W. C., Park N. C., Yoon Y. J., Choi H. & Park Y. P. Investigation of near-field imaging characteristics of radial polarization for application to optical data storage. Opt. Rev. 14, 236–242 (2007). [Google Scholar]
  7. Dehez H., April A. & Piché M. Needles of longitudinally polarized light: guidelines for minimum spot size and tunable axial extent. Opt. Express. 20, 14891–14905 (2012). [DOI] [PubMed] [Google Scholar]
  8. Wang H., Shi L., Lukyanchuk B., Sheppard C. & Chong C. T. Creation of a needle of longitudinally polarized light in vacuum using binary optics. Nat. Photon. 2, 501–505 (2008). [Google Scholar]
  9. Nie Z., Shi G., Zhang X., Wang Y. & Song Y. Generation of super-resolution longitudinally polarized beam with ultra-long depth of focus using radially polarized hollow Gaussian beam. Opt. Commun. 331, 87–93 (2014). [Google Scholar]
  10. Ravi V. et al. Generation of sub-wavelength longitudinal magnetic probe using high numerical aperture lens axicon and binary phase plate. J. Opt. 14, 055704 (2012). [Google Scholar]
  11. Zha Y., Wei J., Wang H. & Gan F. Creation of an ultra-long depth of focus super-resolution longitudinally polarized beam with a ternary optical element. J. Opt. 15, 075703 (2013). [Google Scholar]
  12. Rajesh K. B., Jaroszewicz Z. & Anbarasan P. M. Improvement of lens axicon’s performance for longitudinally polarized beam generation by adding a dedicated phase transmittance. Opt. Exp. 18, 26799–26805 (2010). [DOI] [PubMed] [Google Scholar]
  13. Wang S. et al. Focus modulation of cylindrical vector beams through negative-index grating lenses. Opt. Commun. 372, 245–249 (2016). [Google Scholar]
  14. Nie Z. et al. Spherical and sub-wavelength longitudinal magnetization generated by 4π tightly focusing radially polarized vortex beams. Opt. Exp. 23, 690–701 (2015). [DOI] [PubMed] [Google Scholar]
  15. Li Q. et al. Nanofocusing of longitudinally polarized light using absorbance modulation. Appl. Phys. Lett. 104, 061103 (2014). [Google Scholar]
  16. Luo J. et al. Tight focusing of radially and azimuthally polarized light with plasmonic metalens. Opt. Commun. 356, 445–450 (2015). [Google Scholar]
  17. Luo J. et al. Fabrication of anisotropically arrayed nano-slots metasurfaces using reflective plasmonic lithography. Nano Scale 7, 18805 (2015). [DOI] [PubMed] [Google Scholar]
  18. Gao P. et al. Enhancing aspect profile of half-pitch 32 nm and 22 nm lithography with plasmonic cavity lens. Appl. Phys. Lett. 106, 093110 (2015). [Google Scholar]
  19. Kotlyar V. V., Stafeev S. S., Liu Y., O’Faolain L. & Kovalev A. A. Analysis of the shape of a subwavelength focal spot for the linearly polarized light. Appl. Opt. 52, 330–339 (2013). [DOI] [PubMed] [Google Scholar]
  20. Yuan G. et al. Planar super-oscillatory lens for sub-diffraction optical needles at violet wavelengths. Sci. Rep. 4, 6333 (2014). [DOI] [PMC free article] [PubMed] [Google Scholar]
  21. Rogers E. T. F. et al. A super-oscillatory lens optical microscope for subwavelength imaging. Nat. Mater. 11, 432 (2012). [DOI] [PubMed] [Google Scholar]
  22. Rogers E. T. F. & Zheludev N. I. Optical super-oscillations: sub-wavelength light focusing and super-resolution imaging. J. Opt. 15, 094008 (2013). [Google Scholar]
  23. Yuan G., Rogers E. T. F., Roy T., Shen Z. & Zheludev N. I. Flat super-oscillatory lens for heat-assisted magnetic recording withsub-50 nm resolution. Opt. Express. 22, 6428–6437 (2014). [DOI] [PubMed] [Google Scholar]
  24. Qin F. et al. Shaping a subwavelength needle with ultra-long focal length by focusing azimuthally polarized light. Sci. Rep. 5, 09977 (2015). [DOI] [PMC free article] [PubMed] [Google Scholar]
  25. Liu T., Tan J., Liu J. & Wang H. Vectorial design of super-oscillatory lens. Opt. Express. 21, 15090–15101 (2013). [DOI] [PubMed] [Google Scholar]
  26. Tang D. et al. Ultrabroadband superoscillatory lens composed by plasmonic metasurfaces for subdiffraction light. Laser and Photonics Reviews 9, 713–719 (2015) [Google Scholar]
  27. Wang C. et al. Super-resolution optical telescopes with local light diffraction shrinkage. Sci. Rep. 5, 18485 (2015) [DOI] [PMC free article] [PubMed] [Google Scholar]
  28. Wang S. Y., Abeysinghe D. C. & Zhan Q. W. Generation of vectorial optical fields with slot-antenna-based metasurface. Opt. Lett. 40, 4711–4712 (2015). [DOI] [PubMed] [Google Scholar]
  29. Chen G. et al. Super-oscillation far-field focusing lens based on ultra-thin width-varied metallic slit array. IEEE Photon. Technol. Lett. 28, 335–338 (2016). [Google Scholar]
  30. Wen Z., He Y., Li Y., Chen L. & Chen G. Super-oscillation focusing lens based on continuous amplitude and binary phase modulation. Opt. Expr. 22, 22163–22171 (2014). [DOI] [PubMed] [Google Scholar]
  31. Chen G. et al. Far-field sub-diffraction focusing lens based on binary amplitude-phase mask for linearly polarized light. Opt. Exp. 24, 11002–11008 (2016). [DOI] [PubMed] [Google Scholar]
  32. Chen G. et al. Super-oscillatory focusing of circularly polarized light by ultra-long focal length planar lens based on binary amplitude-phase modulation. Sci. Rep. 6, 29068 (2016). [DOI] [PMC free article] [PubMed] [Google Scholar]
  33. Jin N. & Rahmat-Samii Y. Advances in particle swarm optimization for antenna designs: real-number, binary, single-objective and multiobjective implementations. IEEE Trans. Antenn. Propag. 55, 556–567 (2007). [Google Scholar]
  34. Huang K. et al. Optimization-free superoscillatory lens using phase and amplitude masks. Laser Photon. Rev. 8, 152–157 (2014). [Google Scholar]
  35. Rogers E. T. F. et al. Super-oscillatory optical needle. App. Phys. Lett. 102, 031108 (2013) [Google Scholar]

Associated Data

This section collects any data citations, data availability statements, or supplementary materials included in this article.

Supplementary Materials

Supplementary Information
srep38859-s1.doc (363.5KB, doc)

Articles from Scientific Reports are provided here courtesy of Nature Publishing Group

RESOURCES