Abstract
Two tungsten disulfide (WS2)-based core-shell nanocomposites were fabricated using readily available reagents and simple procedures. The surface was pre-treated with a surfactant couple in a layer-by-layer approach, enabling good dispersion of the WS2 nanostructures in aqueous media and providing a template for the polymerization of a silica (SiO2) shell. After a Stöber-like reaction, a conformal silica coating was achieved. Inspired by the resulting nanocomposite, a second one was prepared by reacting the surfactant-modified WS2 nanostructures with aniline and an oxidizing agent in an aqueous medium. Here too, a conformal coating of polyaniline (PANI) was obtained, giving a WS2@PANI nanocomposite. Both nanocomposites were analyzed by electron microscopy, energy dispersive X-ray spectroscopy (EDS) and FTIR, verifying the core-shell structure and the character of shells. The silica shell was amorphous and mesoporous and the surface area of the composite increases with shell thickness. Polyaniline shells slightly differ in their morphologies dependent on the acid used in the polymerization process and are amorphous like the silica shell. Electron paramagnetic resonance (EPR) spectroscopy of the WS2@PANI nanocomposite showed variation between bulk PANI and the PANI shell. These two nanocomposites have great potential to expand the use of transition metals dichalcogenides (TMDCs) for new applications in different fields.
Keywords: WS2, functionalization, core-shell, polyaniline, silica
1. Introduction
Nanostructures of tungsten disulfide (WS2) were discovered 25 years ago [1] and have been continuously studied ever since. WS2 inorganic nanotubes (INTs) and fullerene-like nanoparticles (IFs) are closed cylindrical or polyhedral layered structures. WS2 is a part of a chemical group of compounds called transition metal dichalcogenides (TMDC), which are sulfides, selenides and tellurides of group 5 and 6 transition metals. In the same manner that carbon nanotubes (CNTs) are composed of folded graphene sheets, WS2 nanostructure are composed of folded triple-layer S-W-S sheets [2]. The atoms within each triple layer are covalently bonded. Between the triple layers, however, there are weak van der Waals interactions, meaning that these nanostructures are of an anisotropic nature. Due to this anisotropy, WS2 nanostructures (especially IFs) are often added to liquid lubricants for reduction of friction and wear [3,4,5,6,7]. The weak forces between the triple layers facilitate sliding and exfoliation of the layers under rubbing pressure.
Inorganic nanostructures are an excellent alternative to CNTs for mechanical reinforcement. WS2 nanostructures have high strength moduli and a good ability for shock absorbing [7]. These mechanical properties allow their use for reinforcement of different polymeric matrices [8,9,10].
In addition to the tribological and mechanical advantages of WS2 nanostructures, they have low cytotoxicity and high biodegradability [11,12,13], unlike CNTs. This adds the possibility of using WS2 nanostructures in biological and medical applications.
Surface functionalization of nanostructures in general and of TMDC nanostructures in particular, is important for two main reasons: First, the functionalized nanostructures will have a better ability of incorporation in different media and matrices. Second, functionalization can add beneficial attributes to the nanostructure, resulting in a larger number of possible applications of the nanocomposite compared to the bare nanostructure. For TMDC nanostructures specifically, the following examples from the literature will demonstrate the benefit in surface functionalization.
Tremel, Tahir and their co-workers have been researching in this field of TMDC functionalization for over a decade now. They developed a general technique for the functionalization of TMDC nanostructures that employs a nitrilotriacetic acid (NTA) ligand to immobilize functional molecules on the outer sulfur layer [14]. Because of the difficulty to anchor organic ligands to the relatively inert sulfur surface, a nickel cation, which has a high sulfur affinity and an octahedral coordination is used. Chelation of the tetradentate NTA with the cation leaves the rest of the nickel coordination sphere free for docking to the sulfur layer. A variety of chemical moieties can be attached to NTA. In other words, Ni-NTA has high affinity to TMDC walls from one end and versatile functionality from the other end. Variations of this technique were used for dispersion of MoS2 IFs in water [14], for attachment of titania nanoparticle to WS2 INTs [15], for binding of the biocatalysts protein silicatein to WS2 INTs [16] and for conjugation of protoporphyrin to ReS2 IFs [17]. By a similar metal-ligand principal, Fe-terpyridine was used on ReS2 IFs to increase their dispersibility in different solvents [18]. Another strategy developed in the Tremel group utilizes the HSAB (Hard Soft Acid Base) principle by Pearson. According to this principle, a hard Lewis acid has a tendency to bind with a hard Lewis base and vice versa [19]. The “soft” sulfur surface layer has then a tendency to bind with other nanoparticles containing soft transition metal cations. This strategy was used for reversible functionalization of WS2 nanotubes and MoS2 IFs with MnO, Fe2O3, Fe3O4, ZnO, gold and platinum nanoparticles [20,21,22]. Shahar et al. used surface defects to functionalize WS2 IFs with alkyl–silane molecules for better dispersion in oil-based suspensions [23] and to attach gold nanoparticle to WS2 INTs [24]. Polyakov et al. decorated MoS2 and WS2 nanostructures with gold nanoparticles by adding a suspension of the nanostructure into boiling aqueous solutions of HAuCl4 [25]. Next, two more optional types of functional shells for TMDC nanostructures will be discussed—silica and polyaniline.
Silica coating and amorphous silica coating in particular, is one of the best, most studied and most versatile types of functional shells. A partial list of its advantages includes chemical and thermal stability, biocompatibility, reduced toxicity and optical transparency. A silica coating is relatively easy and inexpensive to prepare. Additionally, it improves dispersibility in a wide range of media, especially aqueous. It also provides the option for further surface modification of the nanocomposite through the use of functional silicates and attachment of different molecules, such as dyes, to the coating. The literature contains a large number of applications for silica-coated nanomaterials, in a variety of fields. Presented here are a few examples. Silica coating enhanced emission of NdF3 nanoparticles [26], NaYF4:Yb3+, Er3+ nanoparticles [27] and CuO nanorods [28]. Dispersibility and biocompatibility of luminescent YF3:Tb3+ nanoparticles [29], LaVO4:Eu3+ nanoparticles [30] and LaPO4:Eu@ LaPO4 nanorods [31] were improved by silica coating, increasing their potential uses in biomedical science. Silica coating prevented aggregation of magnesium ferrite [32] and cobalt ferrite [33] nanoparticles, while maintaining their magnetic properties. Fe3O4 nanoparticles with a siliceous shell were used for removing heavy metal ions from water [34,35]. A gas-phase silica encapsulation technology was applied to reduce the toxicity of fumes generated by flame [36] or welding [37]. Ultrafine diamonds, used for ultra-precision grinding, were coated with silica to improve their oxidation resistance [38]. Silica coating reduced the toxicity of CeO2 [39,40] and ZnO [41] nanoparticles. Due to its good specific charge capacity, silicon-based electrodes coated with silica can be incorporated in next-generation lithium-ion batteries [42].
Polyaniline (PANI) belongs to a group of conducting organic polymers (COPs), which have been extensively studied and utilized in the last four decades [43]. This group also includes polypyrrole (PPy) [44,45], polycarbazole (PCBz) [46,47], polythiopene (PTh) [48,49], poly [3,4-ethylenedioxythiophene] (PEDOT) [48,50] and others. These polymers (also referred to as synthetic metals) have superior electrical properties and mechanical strength; they are also flexible, environmentally stable and thermally stable.
PANI has been the most attractive and by far, the most studied polymer out of the COPs. In addition to the characteristics described above, PANI is easy to synthesize, inexpensive to produce, structurally diverse, light-weight and corrosion-resistant [51,52,53]. PANI is used for catalysis [54,55], fuel cells [56,57], solar cells [58], supercapacitors [59], sensors [60], corrosion protection [61], printing inks [62], rechargeable batteries [63] and the list goes on. PANI has been incorporated in nanocomposites with graphene [64,65], carbon nanotubes [66,67], metals [68,69,70,71], metal oxides [72,73,74], metal sulfides [75,76,77] and many other materials. Focusing on PANI incorporation with TMDCs, MoS2-PANI nanocomposites have been prepared by in-situ procedures [78,79]. WS2 nanosheets [80] and nanotubes [81] have been incorporated into a PANI matrix.
In this paper, we report the preparation and characterization of two new core-shell nanocomposites—WS2@SiO2 and WS2@PANI. The nanocomposites were prepared using WS2 INTs and IFs that underwent a preliminary layer-by-layer treatment with a surfactant pair, which enabled further polymerizations in polar media. The nanocomposites were analyzed by various methods to verify the formations of the shells and learn about their characteristics. The preparation protocols we present here are not only simple, making use of readily available reagents, instrumentation and techniques and allow the formation of two highly functional polymeric shells but also serve as a synthetic platform for further developments in TMDC functionalization. The pre-treatment alone opens the option for growth of other hydrophilic polymer shells on TMDC nanostructures. The growth of the shells does not rely on surface defects. As a result, they are conformal and have good coverage on the WS2 nanostructures surface. Shell properties, such as thickness and morphology, may be controlled by changing polymerization parameters. Some modifications can be applied in the preparation procedures to produce more TMDC-based core-shell nanocomposites: The core TMDC may vary; substituted silica and PANI monomers can be used in the polymerization process; functional materials/nanoparticles can be encapsulated into the shell. Improved properties and additional uses are among the advantages that core-shell nanocomposites have over the core nanostructure, both in general and for the nanocomposites presented here. For example, fibers and coatings reinforced by TMDC nanostructures will have the added values of antibacterial effect from silica and of electrical conductivity from PANI. This opens possible applications for the nanocomposites in the biomedical field, electrochemistry, textile, plastics and more.
For these reasons, we believe that this work is beneficial. We are hopeful that these nanocomposites will inspire other first- and second-level surface functionalizations of WS2 and other TMDC nanoparticles and expand their existing uses.
2. Experimental Section
Silica coating is usually produced by polymerization of TEOS using a Stöber-like method, in reverse microemulsion [30,82] or sol-gel [26,29,31,32,33,83] setups.
In some cases, TEOS can be polymerized directly on the surface of the core material [34,35]. In other cases, a mediation of a surfactant is needed [27,38,84,85,86].
An attempt to polymerize TEOS directly on WS2 nanostructures did not succeed. TEOS polymerization is done in a polar medium. While such a medium is excellent for the polymerization of TEOS to silica, it is far from ideal for proper dispersion of WS2 nanostructures. The nanostructures rapidly aggregate and sink and the formation of silica nanoparticles separately from the WS2 nanostructures is kinetically favored. To increase the affinity of WS2 towards TEOS, we tried using a protocol previously used to functionalize carbon nanotubes with a mesoporous silica shell [87]. The idea is a layer-by-layer (LbL) coating method wherein two surfactants are used alternately: PSS (poly [sodium p-styrenesulfonate]) and CTAB (cetryltrimethyl ammonium bromide). PSS has some affinity to the WS2 nanostructure walls through hydrophobic interactions. Although one cycle of pre-treatment with the surfactant couple is insufficient to achieve good affinity towards TEOS, five sequential cycles provide a much better coverage and an ionic shell is formed on the nanoparticle. This shell allows increased dispersibility in polar media and serves as a template for silica polymerization.
Polymerization of aniline takes place in an aqueous medium, in which, as mentioned, WS2 nanostructures are not well-dispersed. After the success of the silica coating procedure, we were able to prepare a WS2-PANI core-shell nanocomposite using the surfactant-modifies nanoparticles.
Scheme 1 below summarizes the experimental pathway and full details are given in the following sections.
2.1. Layer-by-Layer Surface Modification of WS2 Nanostructures
An aqueous 1% (wt/wt) PSS solution was prepared by mixing 10 g of PSS (Lot # BCBR9107V, average Mw ~70,000, Sigma-Aldrich, St. Louis, MO, USA), with 990 g of water. The water used for all preparations in this section is ultrapure, purified by a Merck Milli-Q® system (Merck & Co., Kenilworth, NJ, USA).
An aqueous 0.5% (wt/wt) CTAB solution was prepared by mixing 5 g of CTAB (Lot # 054K0083, Sigma-Aldrich, St. Louis, MO, USA) with 995 g of water. Both solutions were sonicated and well-shaken to homogeneity.
5 g of WS2 INTs or IFs (Lot numbers TWPO-MA018 and FWPO-HC019, respectively; NanoMaterials Ltd., Yavne, Israel) were equally divided between four 50 mL conical plastic tubes. 30 mL of 1% PSS solution was added to each tube. To disperse the nanoparticles in the PSS solution, the tubes were sonicated for 20 min in a sonication bath, followed by 30 s of vortex. After dispersion, the tubes were centrifuged for 20 min (7500 RPM, 5 °C) and the liquid was decanted. Then the nanoparticles were washed (same conditions) with 30 mL water, to remove residual PSS. Next, the nanoparticles were dispersed in 30 mL of 0.5% CTAB solution, centrifugation and washing with 30 mL water. This cycle of PSS, water, CTAB and water, was repeated four more times to a total of five cycles. Finally, the contents were washed with 30 mL of ethanol absolute (ACS reagent, Carlo Erba, Milan, Italy) and dried overnight in a vacuum oven at 60 °C.
2.2. Preparation of WS2@SiO2 Nanocomposites
50 mg of nanoparticles after layer-by-layer coating were weighed into a 20 mL vial and dispersed in 10 mL of 0.03% (wt/wt) aqueous CTAB solution (diluted from the 0.5% solution), by 10 min of sonication. A 0.1 M NaOH aqueous solution was prepared by mixing 1 mL of 1 N NaOH standard solution (Lot #: 7576–3700, Daejung, Busan, South Korea) with 9 mL water. From the diluted NaOH solution, 100 µL were then added to the vials while stirring on a plate.
A solution of 100 µL TEOS (puriss, ≥99.0%, Lot #: 1332815, Fluka, St. Louis, MO, USA) in 10 mL ethanol absolute was added to the vial dropwise, using a glass pipette. The vials were left to stir overnight at room temperature (750 RPM).
The next day, the contents were washed with five portions of 30 mL water, followed by 3 portions of 30 mL ethanol absolute (2500 RPM, RT, 15 min). Low speed was chosen to separate between the nanotubes and any silica that might have polymerized in the solution. The contents were then dried overnight in a vacuum oven at 60 °C. These samples are marked INT-SiO2-1P and IF-SiO2-1P.
Alternately, we tried using 5 portions of 10 mL ethanolic TEOS solution, in intervals of 30 min. After each interval, the content was centrifuged (2500 RPM, RT, 15 min) and re-dispersed in 10 mL 0.03% CTAB solution. The final washing and drying steps remained the same. This procedure resulted in a slightly thicker and denser silica coating. These samples are marked INT-SiO2-5P and IF-SiO2-5P.
2.3. Preparation of WS2@PANI Nanocomposites
Aniline polymerization was done in diluted acidic media: hydrochloric acid (HCl) or sulfuric acid (H2SO4), using ammonium persulfate (AMPS) as an oxidizing agent.
A 1M HCl solution was prepared by adding 32% HCl solution (Lot #: 4710-4100, Daejung, Busan, South Korea) to water, filling to 100 mL and mixing. A 0.1M H2SO4 solution was prepared by adding 98% H2SO4 solution (Lot #: 7683–4100, Daejung, Busan, South Korea) to water, filling to 100 mL and mixing. Acidic 0.2M aniline solutions were prepared by adding 91.21 µL of aniline (ACS reagent, 99+%, Lot #: R30A727, Alfa Aeser, Haverhill, MA, USA) to each of the diluted acidic solution mentioned above, filling to 5 mL and mixing.
Acidic 0.25M AMPS solutions were prepared by adding 285.25 mg of AMPS (ACS reagent, 98+%, Lot #: 09406TQ, Sigma-Aldrich, St. Louis, MO, USA) to each of the diluted acidic solution mentioned above, filling to 5 mL and mixing. The aniline and AMPS solutions were freshly prepared for the experiments.
For the coating procedure, 50 mg of nanoparticles after layer-by-layer coating were weighed into a 20 mL vial and dispersed in 10 mL of 0.03% CTAB solution by 10 min of sonication. The vial was then cooled in an ice bath for 10 min. Next, 5 mL of acidic AMPS solution were added, followed by 5 mL of acidic aniline solution. The vials were left to stir (650 RPM) for 30 min at room temperature. The contents were then washed with 30 mL portions of water until washing liquid faded from blue to almost colorless, followed by 2 portions of 30 mL ethanol absolute (1500 RPM, RT, 5 min). The contents were then dried overnight in a vacuum oven at 60 °C. We also tried an experimental variation on the INTs using diluted solutions: 2.5 mL of each acidic solution were used (AMPS and aniline) and 5 mL of the acid solution was added. The rest of the procedure was the same. For HCl solutions, we obtained no coating. For H2SO4 solution, we obtained a slightly thinner coating compared to the original quantities. The samples were marked as follows: INT-PANI-HA and IF-PANI-HA for the samples prepared in hydrochloric acid medium; INT-PANI-SA1 and INT-PANI-SA2 for the INT samples prepared in sulfuric acid medium (diluted and non-diluted, respectively).
2.4. Characterizations
Transmission electron microscopy (TEM) images were acquired by a Tecnai Spirit Bio-Twin microscope (FEI, Hillsboro, OR, USA) equipped with a 1 × 1k CCD camera (Gatan, Pleasanton, CA, USA). Samples for TEM analysis were dispersed in ethanol. A drop of the dispersion was placed on a formvar/carbon film on 400-mesh copper TEM grid (FCF400-Cu, Electron Microscopy Sciences, Hatfield, PA, USA) and dried at room temperature for 2–3 h.
High-resolution scanning electron microscopy (HRSEM) images and elemental line scans were acquired using Magellan 400L high resolution scanning electron microscope (FEI) equipped with an EDS detector. Samples for HRSEM were prepared by placing a few drops of a 0.5 mg/mL ethanolic solution of the dried sample on a square piece of a clean silicon wafer, then coating the sample with 3 nm of sputtered iridium. The silica-coated sample analyzed for elemental line scanning was prepared on a copper grid.
Thermogravimetric analysis (TGA) was performed using a TGA/DSC1 analyzer (Mettler-Toledo, Greifensee, Switzerland). The thermograms were recorded in a nitrogen (50 mL/min) environment at a heating rate of 10 °C min−1 over the temperature range 25–800 °C. The results were processed using STARe evaluation software (Mettler-Toledo, Greifensee, Switzerland).
ATR-FTIR spectra were obtained on a Nicolet iS5 FT-IR spectrometer (Thermo Scientific, Waltham, MA, USA) equipped with an iD5 ATR accessory featuring a laminated diamond crystal. Samples were analyzed as-is. Data processing was performed using OMNIC 9 spectra software (Thermo Scientific, Waltham, MA, USA).
Zeta potential measurements were performed using a Zetasizer Nano-ZS device (Malvern Instruments Ltd., Worcestershire, UK). Samples for zeta potential measurements were dispersed in deionized water (~0.1 mg/mL) and sonicated for five minutes in an ultrasonic bath.
BET (Brunauer–Emmett–Teller) specific surface area (SSA) was determined from nitrogen (N2) adsorption/desorption isotherms measured at liquid nitrogen temperature (−196 °C) using a Nova 3200e® analyzer (Quantachrome instruments, Boynton Beach, FL, USA). The samples were degassed for two hours at 120 °C prior to the analysis. Specific surface area, pore volume and average pore size were determined using the Barrett−Joyner−Halenda (BJH) model. The data were processed using NovaWin™ software (Quantachrome instruments, Boynton Beach, FL, USA).
X-band EPR spectra were recorded at room using an X-band Elexsys E500 EPR spectrometer (Bruker, Karlsruhe, Germany) equipped with an integrated frequency counter. The powdered samples were inserted into narrow quartz tubes (2 mm OD 1 mm ID, Wilmad LabGlass, Vineland, NJ, USA) and placed within standard rectangular Bruker EPR cavity (ER 4119 HS). The EPR device was operated at a microwave frequency of ∼9.88 GHz. Spectra were recorded using a microwave power of 20 mW and gain 120 across a sweep width of 100 G with modulation amplitude of 2 G. Fitting was obtained by using the curve fitting function of the Xepr acquisition software (Bruker, Billerica, MA, USA), for suitable line shapes.
3. Results and Discussion
TEM images of WS2@SiO2 nanocomposites (Figure 1a–h) show that a conformal silica shell was formed around the WS2 INTs and IFs. For the procedure with the smaller amount of TEOS (a,b,e,f), the shell is a few nanometers thick and has a flake-like structure. For the procedure with the larger amount of TEOS (c,d,g,h), the shell is tens of nanometers thick and appears to be denser and smoother. The silica coating is amorphous, as no electron diffraction pattern was obtained from it. To verify the presence of the silica shell, we heated sample INT-SiO2-1P at 600 °C for three hours, under air atmosphere. For comparison, carbon nanotubes are burnt under these conditions, leaving behind hollow SiO2 nanotubes [75]. Under the same conditions, WS2 is merely oxidized to WO3 and the silica stays intact. Hence, we expected at least some change in appearance of the heated sample. TEM images of sample INT-SiO2-1P after heating (Figure 1i,j) show that indeed, the core material has partially collapsed and hollow parts of the silica shells are clearly observed. There are holes in different areas of the shell, which may be a result of particle coating and/or are caused during the WS2 collapse.
TEM images of WS2@PANI nanocomposites (Figure 2) show a uniform, conformal shell formed around the core WS2 INTs and IFs. Similar to the silica shell, the PANI shell seems to coat individual nanoparticles. For the procedure done with hydrochloric acid (a–d), PANI seems to grow in a nano-leaf, or a nano-petal type of structure, where the shape of the “petal” resembles a triangle with its base attached to the core nanostructure and its edge pointing outside. As a result, the “petals” are relatively loosely packed. For the procedure done with sulfuric acid (e–h), the coating seems to be composed of more densely-packed nanosheets. In other publications [88,89], the model of directional growth was used to explain different morphologies of aniline polymers. According to the model, different nano- and micro-structures are formed from aniline oligomers depending on the balance of attractive forces between the oligomer molecules. These forces can be affected by the medium surrounding the oligomers. In our case, it might be possible that the denser packaging is a result of π-π stacking attractive forces, meaning the aniline molecules are oriented in a way that the benzene rings are facing each other. The looser packaging can result from an orientation where the amine groups of the aniline molecules repulse each other. For both preparation procedures, the obtained coating produces no electron diffraction, meaning it is amorphous.
HRSEM images and EDS line scan of sample INT-SiO2-1P (Figure 3) confirm the presence of a conformal shell. The flaky and somewhat incomplete structure of the thin shell is more clearly visible from these images. The shell seems to be coating individual, rather than bundled, nanotubes. Although the shell is only a few nanometers thick, the EDS line scan (c) shows very clear signals of silicon and oxygen going hand in hand with the tungsten and sulfur signals of the nanotube.
HRSEM images of sample INT-PANI-HA (Figure 4a,b) complete the TEM images, presenting a 3-dimensional conformal shell with a spiky texture, coating individual nanotubes. EDS line scan (c) further confirms the core-shell structure of the composite. The PANI coating appears dark, surrounding the lighter WS2 nanotube core. The signals for carbon and nitrogen are relatively wide, implying the presence of these elements all around the composite. Signals for tungsten and especially sulfur are a bit narrower with maxima in the lighter core area.
The bands in the FTIR absorbance spectra for SiO2-coated samples were in good agreement with the literature data about nanocomposites coated with amorphous silica [27,29,32,34,38]. The spectrum of the representative sample INT-SiO2-1P is presented in Figure 5. The band at 1074 cm−1 is assigned to Si-O-Si asymmetric stretches. The band at 796 cm−1 is assigned to Si-O-Si symmetric stretches. The band at 455 cm−1 is assigned to O-Si-O bending. The band at 964 cm−1 is assigned to Si-OH asymmetric stretches. The weak bands at 1633 cm−1 and 1463 cm−1 are assigned to O-H bending and wagging.
FTIR absorbance spectrum of sample INT-PANI-HA (Figure 6) shows typical [71,89,90,91,92,93,94] bands for PANI (this sample is representative as the spectra for all PANI-coated samples looked similar). When aniline rings are connected through their amine groups, the aniline unit within the polymer can be found in a benzenoid (B) form and in a quinonoid (Q) form. The former is a benzene-like ring with 1,4-single bonds to nitrogen atoms and the latter has two carbon-carbon double bonds within the ring and two 1,4-double bonds to the nitrogen atoms. The band at 1584 cm−1 is assigned to C=C stretches in the Q ring. The band at 1494 cm−1 is assigned to C=C stretches in the B ring. The band at 1296 cm−1 is assigned to C-N stretches. The bands at 1146 cm−1 and 807 cm−1 are assigned to C-H in-plane and out-of-plane bending, respectively. The band at 493 cm−1 is assigned to C-N-C bending.
To the naked eye, aqueous dispersions of the nanocomposites appeared to be relatively stable overtime, differently aqueous dispersions of bare WS2 INTs and IFs, which aggregate after a few minutes. To test this observation, zeta potentials of bare WS2 INTs, WS2 IFs and their composites were compared. The results in Figure 7 show that indeed, the absolute values of the nanocomposites zeta potentials are significantly higher than those of bare nanostructures; while the former are closer to the aggregation range, the latter indicate dispersions with a moderate stability.
In addition, zeta potential for an aqueous solution of sample INT-SiO2-1P was measured against pH. The trend in the plot presented in Figure 8 is consistent with the literature [95,96,97]. Zeta potential value decreases with increasing pH, to a minimum of −39.4 mV at pH 10. That is the point of maximum stability (highest absolute value) of the solution. When pH rises above 10, zeta potential starts increasing again. Absolute value is decreasing and so is the stability of the solution. This happens because the ionic strength of the medium increases, compressing the electrical double layer around the particle and allowing attractive van der Waals forces to dominate. Usually, the zeta potential of silica is negative only when pH is above 2–3 but in our case, it is negative through the entire pH range. This phenomenon is typical to silica-coated nanocomposites [98,99].
Nitrogen adsorption-desorption analysis was run on the silica-coated WS2 nanotubes to check porosity of the coating and the data is presented in Figure 9. The average pore radii suggest that the coating is mesoporous. The shape of the isotherms agrees with type IV adsorption-desorption curves (IUPAC classification), which are typical for mesoporous materials. The curves have characteristic hysteresis loops that usually result from capillary condensation within the mesoporous structure [100].
The surface areas of the coated samples are an order of magnitude smaller than that of ordered/crystalline mesoporous silica, which can be hundreds to about a thousand m2/g [87,101,102]. This makes sense, as it was previously implied from the TEM images that the coating is amorphous and does not visually resembles ordered mesoporous silica. Nonetheless, there is an evident increase in the surface area and total pore volume when comparing between the coated and non-coated nanotube and between the two coating thicknesses. An interesting option for further modification of the silica coating was using the pseudomorphic transformation method to convert an amorphous silica coating on magnetite nanoparticles to a mesoporous one for DNA plasmid purification [103].
Figure 10 shows the result of thermogravimetric analysis for bare WS2 nanotubes and coated sample INT-PANI-HA. The samples were heated under nitrogen to avoid oxidation of the nanotube. The plot presents an overall weight loss of 6.5%. An initial weight loss of 0.5% occurs under about 150 °C (arrow 1) and is assigned to moisture. In the range of 150 °C to 350 °C there is a weight loss of 5% which may be assigned to residual HCl used in the polymerization process but can also originate from shorter aniline oligomers. Another weight loss starts at 350 °C (arrow 2) and is assigned to the polyaniline backbone. It is interesting to note that although the weight loss ranges are relatively typical to polyaniline [68,73,104], their parts in the weight loss are not. It is expected that the major weight loss will be the one above 350 °C and the case here is different. Because the sample was well-washed before analysis and the pH of the medium was neutral, the contribution of residual HCl should not be significant. It is possible that the PANI shell contains a large number of shorter units, which causes its decomposition to start below 350 °C.
Figure 11 shows the EPR spectra for bare WS2 nanotubes (inset), PANI and WS2@PANI composite (sample INT-PANI-SA2 was tested). The PANI sample was prepared in the same manner as the composite sample mentioned above, excluding WS2 INTs. EPR signal for bare WS2 nanotubes is negligible. An intense EPR peak of free radical without hyperfine structure appears for PANI and WS2@PANI samples. This peak is ascribed to the presence of polarons in these samples. The polarons, free electron, in conducting polymers are characterized by electron spin S = ½. Thus, EPR methods are widely used for the study of such systems. Looking carefully at the PANI spectrum, it seems to be composed from two components, a narrow Lorentzian peak (dashed line, ΔHpp = 1.8 G) and broader one (dotted line, ΔHpp = 3.8 G). These two components can be related to the bulk polymer polaron spins and to surface polymer polaron spins: the broader component is related to exposure of the polymer surface to oxygen, causing line width increase due to dipole-dipole interaction of the polaron with the paramagnetic oxygen [105]. Another explanation can be that PANI preparation methods still have uncontrolled and incomplete polymerization mechanism. This results in multicomponent product, with different morphologies [106]. It is possible that the PANI consists of different domains having different degree of localization/motion of the polarons domains. Component with decreased localization will have increased spin diffusion and narrow linewidth due to motional exchange narrowing [107,108]. However, WS2@PANI EPR is composed from a single component and therefore may reflect a higher degree of structural order of the PANI within the composite, compared to the bulk PANI. The g-values of the EPR signal were 2.0028 and 2.0034, respectively and the ΔHpp of these signals were 4.4 G and 3 G, respectively.
The g-values are very close to that of the free electron g = 2.0023 or to that of a carbon center radical 2.002–2.003 [109]. They are typical for free radicals of π-system in polyenes and aromatics [110], where the electrons delocalized over the polymeric systems consisting of pz orbitals of carbon and nitrogen atoms in the main chain of polyaniline. In both samples, the observed small line width suggests mobility of the spins and also strong exchange coupling. Similar g-values and ΔHpp as measured in this work are listed in the literature of PANI [105,108,111,112,113]. The line shape of WS2@PANI has a symmetric Lorentzian line with A/B ~1, while the PANI has an asymmetric Lorentzian line shape with A/B ~1.2. This asymmetry may arise from unresolved anisotropy of g-value or, most likely, from the dysonian character of PANI [113]. The dysonian line shape is common, registered in conductive samples such as highly-doped PANI, having a skin depth smaller than the sample thickness [114]. Thus, a non-uniform distribution of the microwave field in the sample causes a dispersive component in the line shape resulting in asymmetry [115]. As Dysonian is accompanied by line shift to a higher magnetic field [108], the decrease in the g-value to 2.0028, compared to 2.0034 in WS2@PANI is another indication for the dysonian character of PANI, which is not represented in WS2@PANI. We can suggest that WS2 decreases the conductivity of PANI with an increase in the skin depth, causing a symmetric peak. One explanation to the possible decrease in the conductivity of WS2@PANI can be a decrease in spin density. As PANI coats the WS2 surface, there is a decrease in the bulk polymer concentration and as a result, a decrease in the total spin density and in conductivity. This can also explain the decrease in the linewidth of WS2@PANI, since the decrease in the spin density will also decrease the dipole interactions of the spins with neighbors.
4. Conclusions
Two new core-shell nanocomposites were introduced: WS2@SiO2 and WS2@PANI. Their preparation was based on a preliminary treatment of the WS2 nanostructures followed by polymerization of TEOS or aniline on the surface of the WS2 INTs or IFs. Structural analysis confirmed the presence and characters of the obtained conformal shells. The silica shell is amorphous and mesoporous. Its thickness and as a result—its surface area, can be adjusted. The stability of the aqueous WS2@SiO2 dispersion can be increased by pH adjustment.
Polyaniline also formed an amorphous shell around the WS2 core. Different acids used in the polymerization process lead to slightly different shell morphologies. EPR of the WS2@PANI nanocomposite shows that PANI character within the composite is slightly different from its bulk character.
This work is merely a first step towards a wider use of TMDC nanostructures. The silica shell is mesoporous and substituted TEOS can be used to produce a hybrid silica shell. PANI is a very versatile conductive polymer which can be prepared under many conditions and with different dopants and it differs in its properties accordingly. In addition, the LbL surface modification done on the core TMDC allows other water-soluble monomers to be tested as shell precursors. We are currently working on testing the nanocomposites described here as enhanced reinforcing agents in polymeric fibers and coatings. For further work, our thoughts include testing WS2@SiO2 nanocomposites in biomedical applications and WS2@PANI for Li-ion batteries.
Acknowledgments
We thank NanoMaterials Ltd. for their generous gift of WS2 nanotubes and fullerene-like nanoparticles. We thank the Israel National Nanotechnology Initiative for partial funding of this research. We thank Merav Muallem, Ortal Lidor-Shalev and Netanel Shpigel (Bar-Ilan University, Institute for Nanotechnology and Advanced Materials) for dedicating the time to provide us with their kind and professional help in producing the HRSEM images and EDS analysis for this paper. We deeply thank Ronit Lavi (Bar Ilan University, Department of Chemistry) for her extensive help with EPR analysis and for providing us with her enlightening input.
Author Contributions
H.S. Prepared and analyzed the functionalized nanoparticles and wrote the paper. J.-P.L. contributed reagents, materials and analysis tools, revised the paper and approved submission.
Conflicts of Interest
The authors declare no conflict of interest.
References
- 1.Tenne R., Margulis L., Genut M., Hodes G. Polyhedral and cylindrical structures of tungsten disulphide. Nature. 1992;360:444–446. doi: 10.1038/360444a0. [DOI] [Google Scholar]
- 2.Tenne R. Inorganic nanotubes and fullerene-like nanoparticles. Nat. Nano. 2006;1:103–111. doi: 10.1038/nnano.2006.62. [DOI] [PubMed] [Google Scholar]
- 3.Rapoport L., Bilik Y., Feldman Y., Homyonfer M., Cohen S.R., Tenne R. Hollow nanoparticles of WS2 as potential solid-state lubricants. Nature. 1997;387:791–793. doi: 10.1038/42910. [DOI] [Google Scholar]
- 4.Jenei I.Z., Svahn F., Csillag S. Correlation Studies of WS2 Fullerene-Like Nanoparticles Enhanced Tribofilms: A Scanning Electron Microscopy Analysis. Tribol. Lett. 2013;51:461–468. doi: 10.1007/s11249-013-0184-0. [DOI] [Google Scholar]
- 5.Rapoport L., Lvovsky M., Lapsker I., Leshchinsky W., Volovik Y., Feldman Y., Tenne R. Friction and wear of bronze powder composites including fullerene-like WS2 nanoparticles. Wear. 2001;249:149–156. doi: 10.1016/S0043-1648(01)00519-1. [DOI] [Google Scholar]
- 6.Rapoport L., Lvovsky M., Lapsker I., Leshinsky V., Volovik Y., Feldman Y., Zak A., Tenne R. Slow Release of Fullerene-Like WS2 Nanoparticles as a Superior Solid Lubrication Mechanism in Composite Matrices. Adv. Eng. Mater. 2001;3:71–75. doi: 10.1002/1527-2648(200101)3:1/2<71::AID-ADEM71>3.0.CO;2-M. [DOI] [Google Scholar]
- 7.Kaplan-Ashiri I., Tenne R. Mechanical Properties of WS2 Nanotubes. J. Clust. Sci. 2007;18:549–563. doi: 10.1007/s10876-007-0118-9. [DOI] [Google Scholar]
- 8.Place E.S., George J.H., Williams C.K., Stevens M.M. Synthetic polymer scaffolds for tissue engineering. Chem. Soc. Rev. 2009;38:1139–1151. doi: 10.1039/b811392k. [DOI] [PubMed] [Google Scholar]
- 9.Flores A., Naffakh M., Díez-Pascual A.M., Ania F., Gómez-Fatou M.A. Evaluating the Reinforcement of Inorganic Fullerene-like Nanoparticles in Thermoplastic Matrices by Depth-Sensing Indentation. J. Phys. Chem. C. 2013;117:20936–20943. doi: 10.1021/jp406513y. [DOI] [Google Scholar]
- 10.Lalwani G., Henslee A.M., Farshid B., Parmar P., Lin L., Qin Y.-X., Kasper F.K., Mikos A.G., Sitharaman B. Tungsten disulfide nanotubes reinforced biodegradable polymers for bone tissue engineering. Acta Biomater. 2013;9:8365–8373. doi: 10.1016/j.actbio.2013.05.018. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 11.Pardo M., Shuster-Meiseles T., Levin-Zaidman S., Rudich A., Rudich Y. Low Cytotoxicity of Inorganic Nanotubes and Fullerene-Like Nanostructures in Human Bronchial Epithelial Cells: Relation to Inflammatory Gene Induction and Antioxidant Response. Environ. Sci. Technol. 2014;48:3457–3466. doi: 10.1021/es500065z. [DOI] [PubMed] [Google Scholar]
- 12.Asadi V., Jafari S.H., Khonakdar H.A., Häuβler L., Wagenknecht U. Incorporation of inorganic fullerene-like WS2 into poly(ethylene succinate) to prepare novel biodegradable nanocomposites: A study on isothermal and dynamic crystallization. RSC Adv. 2016;6:4925–4935. doi: 10.1039/C5RA24898A. [DOI] [Google Scholar]
- 13.Silverman T., Naffakh M., Marco C., Ellis G. Morphology and thermal properties of biodegradable poly(hydroxybutyrate-co-hydroxyvalerate)/tungsten disulphide inorganic nanotube nanocomposites. Mater. Chem. Phys. 2016;170:145–153. doi: 10.1016/j.matchemphys.2015.12.032. [DOI] [Google Scholar]
- 14.Tahir M.N., Zink N., Eberhardt M., Therese H.A., Kolb U., Theato P., Tremel W. Overcoming the Insolubility of Molybdenum Disulfide Nanoparticles through a High Degree of Sidewall Functionalization Using Polymeric Chelating Ligands. Angew. Chem. Int. Ed. 2006;45:4809–4815. doi: 10.1002/anie.200504211. [DOI] [PubMed] [Google Scholar]
- 15.Tahir M.N., Zink N., Eberhardt M., Therese H.A., Faiss S., Janshoff A., Kolb U., Theato P., Tremel W. Hierarchical Assembly of TiO2 Nanoparticles on WS2 Nanotubes Achieved Through Multifunctional Polymeric Ligands. Small. 2007;3:829–834. doi: 10.1002/smll.200600663. [DOI] [PubMed] [Google Scholar]
- 16.Tahir M.N., Yella A., Therese H.A., Mugnaioli E., Panthöfer M., Khan H.U., Knoll W., Kolb U., Tremel W. Synthesis of Hierarchically Grown ZnO@NT-WS2 Nanocomposites. Chem. Mater. 2009;21:5382–5387. doi: 10.1021/cm901534m. [DOI] [Google Scholar]
- 17.Tahir M.N., Yella A., Sahoo J.K., Natalio F., Kolb U., Jochum F., Theato P., Tremel W. IF-ReS2 with Covalently Linked Porphyrin Antennae. Isr. J. Chem. 2010;50:500–505. doi: 10.1002/ijch.201000053. [DOI] [Google Scholar]
- 18.Sahoo J.K., Tahir M.N., Yella A., Branscheid R., Kolb U., Tremel W. Soluble IF-ReS2 Nanoparticles by Surface Functionalization with Terpyridine Ligands. Langmuir. 2011;27:385–391. doi: 10.1021/la103687y. [DOI] [PubMed] [Google Scholar]
- 19.Pearson R.G. Hard and Soft Acids and Bases. J. Am. Chem. Soc. 1963;85:3533–3539. doi: 10.1021/ja00905a001. [DOI] [Google Scholar]
- 20.Sahoo J.K., Tahir M.N., Yella A., Schladt T.D., Mugnaoli E., Kolb U., Tremel W. Reversible Self-Assembly of Metal Chalcogenide/Metal Oxide Nanostructures Based on Pearson Hardness. Angew. Chem. Int. Ed. 2010;49:7578–7582. doi: 10.1002/anie.201000774. [DOI] [PubMed] [Google Scholar]
- 21.Sahoo J.K., Tahir M.N., Yella A., Schladt T.D., Pfeiffer S., Nakhjavan B., Mugnaioli E., Kolb U., Tremel W. From Single Molecules to Nanoscopically Structured Materials: Self-Assembly of Metal Chalcogenide/Metal Oxide Nanostructures Based on the Degree of Pearson Hardness. Chem. Mater. 2011;23:3534–3539. doi: 10.1021/cm201178n. [DOI] [Google Scholar]
- 22.Sahoo J.K., Tahir M.N., Hoshyargar F., Nakhjavan B., Branscheid R., Kolb U., Tremel W. Molecular Camouflage: Making Use of Protecting Groups To Control the Self-Assembly of Inorganic Janus Particles onto Metal–Chalcogenide Nanotubes by Pearson Hardness. Angew. Chem. Int. Ed. 2011;50:12271–12275. doi: 10.1002/anie.201105337. [DOI] [PubMed] [Google Scholar]
- 23.Shahar C., Zbaida D., Rapoport L., Cohen H., Bendikov T., Tannous J., Dassenoy F., Tenne R. Surface Functionalization of WS2 Fullerene-like Nanoparticles. Langmuir. 2009;26:4409–4414. doi: 10.1021/la903459t. [DOI] [PubMed] [Google Scholar]
- 24.Shahar C., Levi R., Cohen S.R., Tenne R. Gold Nanoparticles as Surface Defect Probes for WS2 Nanostructures. J. Phys. Chem. Lett. 2010;1:540–543. doi: 10.1021/jz900332h. [DOI] [Google Scholar]
- 25.Polyakov A.Y., Yadgarov L., Popovitz-Biro R., Lebedev V.A., Pinkas I., Rosentsveig R., Feldman Y., Goldt A.E., Goodilin E.A., Tenne R. Decoration of WS2 Nanotubes and Fullerene-Like MoS2 with Gold Nanoparticles. J. Phys. Chem. C. 2014;118:2161–2169. doi: 10.1021/jp407388h. [DOI] [Google Scholar]
- 26.Ansari A.A., Singh S.P., Singh N., Malhotra B.D. Synthesis of optically active silica-coated NdF3 core–shell nanoparticles. Spectrochim. Acta Part A Mol. Biomol. Spectrosc. 2012;86:432–436. doi: 10.1016/j.saa.2011.10.063. [DOI] [PubMed] [Google Scholar]
- 27.Liu P., Zhou G., Chen S., Wang S. Synthesis and up-conversion photoluminescence properties of NaYF4:Yb3+, Er3+@sSiO2@mSiO2 nanoparticles. Opt. Mater. 2014;36:1443–1448. doi: 10.1016/j.optmat.2013.11.002. [DOI] [Google Scholar]
- 28.Jin C., Kim H., Hong C., Kim H.W., Lee C. Preparation and photoluminescence properties of silica-coated CuO nanowires. Appl. Phys. A. 2010;100:151–157. doi: 10.1007/s00339-010-5589-0. [DOI] [Google Scholar]
- 29.Ansari A.A. Impact of surface coating on morphological, optical and photoluminescence properties of YF3:Tb3+ nanoparticles. Chin. Chem. Lett. 2017;28:651–657. doi: 10.1016/j.cclet.2016.10.010. [DOI] [Google Scholar]
- 30.Ansari A.A., Alam M., Labis J.P., Alrokayan S.A., Shafi G., Hasan T.N., Syed N.A., Alshatwi A.A. Luminescent mesoporous LaVO4:Eu3+ core-shell nanoparticles: Synthesis, characterization, biocompatibility and their cytotoxicity. J. Mater. Chem. 2011;21:19310–19316. doi: 10.1039/c1jm12871j. [DOI] [Google Scholar]
- 31.Ansari A.A. Silica-modified luminescent LaPO4:Eu@LaPO4@SiO2 core/shell nanorods: Synthesis, structural and luminescent properties. Luminescence. 2018;33:112–118. doi: 10.1002/bio.3379. [DOI] [PubMed] [Google Scholar]
- 32.Das H., Arai T., Debnath N., Sakamoto N., Shinozaki K., Suzuki H., Wakiya N. Impact of acidic catalyst to coat superparamagnetic magnesium ferrite nanoparticles with silica shell via sol–gel approach. Adv. Powder Technol. 2016;27:541–549. doi: 10.1016/j.apt.2016.02.009. [DOI] [Google Scholar]
- 33.Lyubutin I.S., Starchikov S.S., Gervits N.E., Korotkov N.Y., Dmitrieva T.V., Lin C.-R., Tseng Y.-T., Shih K.-Y., Lee J.-S., Wang C.-C. Canted spin structure and the first order magnetic transition in CoFe2O4 nanoparticles coated by amorphous silica. J. Magn. Magn. Mater. 2016;415:13–19. doi: 10.1016/j.jmmm.2016.01.090. [DOI] [Google Scholar]
- 34.Tavares D.S., Daniel-da-Silva A.L., Lopes C.B., Silva N.J.O., Amaral V.S., Rocha J., Pereira E., Trindade T. Efficient sorbents based on magnetite coated with siliceous hybrid shells for removal of mercury ions. J. Mater. Chem. A. 2013;1:8134–8143. doi: 10.1039/c3ta10914c. [DOI] [Google Scholar]
- 35.Majeed J., Ramkumar J., Chandramouleeswaran S., Tyagi A.K. Fe3O4@SiO2 core-shell nanoparticles: Synthesis, characterization and application in environmental remediation. AIP Conf. Proc. 2014;1591:605–607. doi: 10.1063/1.4872690. [DOI] [Google Scholar]
- 36.Gass S., Cohen J.M., Pyrgiotakis G., Sotiriou G.A., Pratsinis S.E., Demokritou P. Safer Formulation Concept for Flame-Generated Engineered Nanomaterials. ACS Sustain. Chem. Eng. 2013;1:843–857. doi: 10.1021/sc300152f. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 37.Wang J., Wu C.-Y., Franke G. Effectiveness of amorphous silica encapsulation technology on welding fume particles and its impact on mechanical properties of welds. Mater. Des. 2014;54:79–86. doi: 10.1016/j.matdes.2013.08.002. [DOI] [Google Scholar]
- 38.Zhao D., Wang Z., Xi Y., Zou Q., Li X., Wang B., Guo X., Liang M., Li W., Wang M., et al. Preparation of silica-coated ultrafine diamond and dispersion in ceramic matrix. Mater. Lett. 2013;113:134–137. doi: 10.1016/j.matlet.2013.09.052. [DOI] [Google Scholar]
- 39.Konduru N.V., Jimenez R.J., Swami A., Friend S., Castranova V., Demokritou P., Brain J.D., Molina R.M. Silica coating influences the corona and biokinetics of cerium oxide nanoparticles. Part. Fibre Toxicol. 2015;12 doi: 10.1186/s12989-015-0106-4. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 40.Davidson D.C., Derk R., He X., Stueckle T.A., Cohen J., Pirela S.V., Demokritou P., Rojanasakul Y., Wang L. Direct stimulation of human fibroblasts by nCeO2 in vitro is attenuated with an amorphous silica coating. Part. Fibre Toxicol. 2016;13:23. doi: 10.1186/s12989-016-0134-8. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 41.Konduru N.V., Murdaugh K.M., Swami A., Jimenez R.J., Donaghey T.C., Demokritou P., Brain J.D., Molina R.M. Surface modification of zinc oxide nanoparticles with amorphous silica alters their fate in the circulation. Nanotoxicology. 2016;10:720–727. doi: 10.3109/17435390.2015.1113322. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 42.Ostadhossein A., Kim S.-Y., Cubuk E.D., Qi Y., van Duin A.C.T. Atomic Insight into the Lithium Storage and Diffusion Mechanism of SiO2/Al2O3 Electrodes of Lithium Ion Batteries: ReaxFF Reactive Force Field Modeling. J. Phys. Chem. A. 2016;120:2114–2127. doi: 10.1021/acs.jpca.5b11908. [DOI] [PubMed] [Google Scholar]
- 43.Heeger A.J. Semiconducting and metallic polymers: The fourth generation of polymeric materials. Synth. Met. 2001;125:23–42. doi: 10.1016/S0379-6779(01)00509-4. [DOI] [PubMed] [Google Scholar]
- 44.Vernitskaya T.V., Efimov O.N. Polypyrrole: A conducting polymer; its synthesis, properties and applications. Russ. Chem. Rev. 1997;66:443. doi: 10.1070/RC1997v066n05ABEH000261. [DOI] [Google Scholar]
- 45.Ateh D.D., Navsaria H.A., Vadgama P. Polypyrrole-based conducting polymers and interactions with biological tissues. J. R. Soc. Interface. 2006;3:741–752. doi: 10.1098/rsif.2006.0141. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 46.Raj V., Madheswari D., Mubarak Ali M. Chemical formation, characterization and properties of polycarbazole. J. Appl. Polym. Sci. 2010;116:147–154. doi: 10.1002/app.31511. [DOI] [Google Scholar]
- 47.Ates M., Uludag N. Carbazole derivative synthesis and their electropolymerization. J. Solid State Electrochem. 2016;20:2599–2612. doi: 10.1007/s10008-016-3269-5. [DOI] [Google Scholar]
- 48.Roncali J. Conjugated poly(thiophenes): Synthesis, functionalization, and applications. Chem. Rev. 1992;92:711–738. doi: 10.1021/cr00012a009. [DOI] [Google Scholar]
- 49.Schopf G., Koßmehl G. Polythiophenes—Electrically Conductive Polymers. Springer; Berlin/Heidelberg, Germany: 1997. Properties of poly(thiophene)s; pp. 51–80. [Google Scholar]
- 50.Lövenich W. PEDOT-properties and applications. Polym. Sci. Ser. C. 2014;56:135–143. doi: 10.1134/S1811238214010068. [DOI] [Google Scholar]
- 51.Stejskal J., Sapurina I. Polyaniline—A Conducting Polymer. In: Schubert U., Hüsing N., Laine R.M., editors. Materials Syntheses: A Practical Guide. Springer; Vienna, Austria: 2008. pp. 199–207. [Google Scholar]
- 52.Boeva Z.A., Sergeyev V.G. Polyaniline: Synthesis, properties, and application. Polym. Sci. Ser. C. 2014;56:144–153. doi: 10.1134/S1811238214010032. [DOI] [Google Scholar]
- 53.Bhadra S., Singha N.K., Khastgir D. Electrochemical synthesis of polyaniline and its comparison with chemically synthesized polyaniline. J. Appl. Polym. Sci. 2007;104:1900–1904. doi: 10.1002/app.25867. [DOI] [Google Scholar]
- 54.Palaniappan S., Saravanan C., Amarnath C.A., Rao V.J. Polyaniline Salts and Complexes as Catalyst in Bisindole Synthesis. Catal. Lett. 2004;97:77–81. doi: 10.1023/B:CATL.0000034291.79388.19. [DOI] [Google Scholar]
- 55.Chabukswar V.V., Handore K.N., Bhavsar S.V., Horne A.S., Dallavalle S., Gaikwad V., Mohite K.C. Conducting Polyaniline is an Efficient Catalyst for Synthesis of 3,4-dihydropyrimidin-2-(1H)-one Derivative Under Solvent-Free Conditions. J. Macromol. Sci. Part A. 2013;50:411–415. doi: 10.1080/10601325.2013.768157. [DOI] [Google Scholar]
- 56.Lai B., Tang X., Li H., Du Z., Liu X., Zhang Q. Power production enhancement with a polyaniline modified anode in microbial fuel cells. Biosens. Bioelectron. 2011;28:373–377. doi: 10.1016/j.bios.2011.07.050. [DOI] [PubMed] [Google Scholar]
- 57.Mehdinia A., Dejaloud M., Jabbari A. Nanostructured polyaniline-coated anode for improving microbial fuel cell power output. Chem. Pap. 2013;67:1096–1102. doi: 10.2478/s11696-013-0381-1. [DOI] [Google Scholar]
- 58.Wu J., Li Y., Tang Q., Yue G., Lin J., Huang M., Meng L. Bifacial dye-sensitized solar cells: A strategy to enhance overall efficiency based on transparent polyaniline electrode. Sci. Rep. 2014;4:4028. doi: 10.1038/srep04028. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 59.Wang H., Lin J., Shen Z.X. Polyaniline (PANi) based electrode materials for energy storage and conversion. J. Sci. Adv. Mater. Devices. 2016;1:225–255. doi: 10.1016/j.jsamd.2016.08.001. [DOI] [Google Scholar]
- 60.Ahuja T., Kumar D. Recent progress in the development of nano-structured conducting polymers/nanocomposites for sensor applications. Sens. Actuators B Chem. 2009;136:275–286. doi: 10.1016/j.snb.2008.09.014. [DOI] [Google Scholar]
- 61.Fayyad E.M., Sanad S.H., Ismail A.A. Coatings of Conducting Polymers for Corrosion Protection of Mild Steel. Silicon. 2017;9:901–915. doi: 10.1007/s12633-016-9518-5. [DOI] [Google Scholar]
- 62.De Barros R.A., Martins C.R., de Azevedo W.M. Writing with conducting polymer. Synth. Met. 2005;155:35–38. doi: 10.1016/j.synthmet.2005.05.014. [DOI] [Google Scholar]
- 63.Novák P., Müller K., Santhanam K.S.V., Haas O. Electrochemically Active Polymers for Rechargeable Batteries. Chem. Rev. 1997;97:207–282. doi: 10.1021/cr941181o. [DOI] [PubMed] [Google Scholar]
- 64.Modak P., Kondawar S.B., Nandanwar D.V. Synthesis and Characterization of Conducting Polyaniline/Graphene Nanocomposites for Electromagnetic Interference Shielding. Procedia Mater. Sci. 2015;10:588–594. doi: 10.1016/j.mspro.2015.06.010. [DOI] [Google Scholar]
- 65.Sheng X., Cai W., Zhong L., Xie D., Zhang X. Synthesis of Functionalized Graphene/Polyaniline Nanocomposites with Effective Synergistic Reinforcement on Anticorrosion. Ind. Eng. Chem. Res. 2016;55:8576–8585. doi: 10.1021/acs.iecr.6b01975. [DOI] [Google Scholar]
- 66.Oueiny C., Berlioz S., Perrin F.-X. Carbon nanotube–polyaniline composites. Prog. Polym. Sci. 2014;39:707–748. doi: 10.1016/j.progpolymsci.2013.08.009. [DOI] [Google Scholar]
- 67.Kumar A., Kumar V., Awasthi K. Polyaniline–Carbon Nanotube Composites: Preparation Methods, Properties, and Applications. Polym. Plast. Technol. Eng. 2017;0:1–28. doi: 10.1080/03602559.2017.1300817. [DOI] [Google Scholar]
- 68.Blinova N.V., Stejskal J., Trchová M., Sapurina I., Ćirić-Marjanović G. The oxidation of aniline with silver nitrate to polyaniline–silver composites. Polymer. 2009;50:50–56. doi: 10.1016/j.polymer.2008.10.040. [DOI] [Google Scholar]
- 69.Khan A., Asiri A.M., Rub M.A., Azum N., Khan A.A.P., Khan S.B., Rahman M.M., Khan I. Synthesis, characterization of silver nanoparticle embedded polyaniline tungstophosphate-nanocomposite cation exchanger and its application for heavy metal selective membrane. Compos. Part B Eng. 2013;45:1486–1492. doi: 10.1016/j.compositesb.2012.09.023. [DOI] [Google Scholar]
- 70.Soni A., Pandey C.M., Solanki S., Sumana G. One-pot synthesis of a polyaniline-gold nanocomposite and its enhanced electrochemical properties for biosensing applications. RSC Adv. 2015;5:45767–45774. doi: 10.1039/C5RA06146F. [DOI] [Google Scholar]
- 71.Wang W., Sun S., Gu S., Shen H., Zhang Q., Zhu J., Wang L., Jiang W. One-pot fabrication and thermoelectric properties of Ag nanoparticles-polyaniline hybrid nanocomposites. RSC Adv. 2014;4:26810–26816. doi: 10.1039/C4RA02136C. [DOI] [Google Scholar]
- 72.Sathiyanarayanan S., Azim S.S., Venkatachari G. Preparation of polyaniline–TiO2 composite and its comparative corrosion protection performance with polyaniline. Synth. Met. 2007;157:205–213. doi: 10.1016/j.synthmet.2007.01.012. [DOI] [Google Scholar]
- 73.Mostafaei A., Zolriasatein A. Synthesis and characterization of conducting polyaniline nanocomposites containing ZnO nanorods. Prog. Nat. Sci. Mater. Int. 2012;22:273–280. doi: 10.1016/j.pnsc.2012.07.002. [DOI] [Google Scholar]
- 74.Javadian H., Angaji M.T., Naushad M. Synthesis and characterization of polyaniline/γ-alumina nanocomposite: A comparative study for the adsorption of three different anionic dyes. J. Ind. Eng. Chem. 2014;20:3890–3900. doi: 10.1016/j.jiec.2013.12.095. [DOI] [Google Scholar]
- 75.Ramesan M.T. Synthesis, characterization, and properties of new conducting polyaniline/copper sulfide nanocomposites. Polym. Eng. Sci. 2014;54:438–445. doi: 10.1002/pen.23572. [DOI] [Google Scholar]
- 76.Ghoswami M., Ghosh R., Chakraborty G., Gupta K., Meikap A.K. Optical and electrical properties of polyaniline-cadmium sulfide nanocomposite. Polym. Compos. 2011;32:2017–2027. doi: 10.1002/pc.21235. [DOI] [Google Scholar]
- 77.Batool A., Kanwal F., Riaz S., Abbas A., Naseem S. Novel Method to Synthesize Conducting Polyaniline/nickle Sulphide Nanocomposite Films and the Study of their Structural and Electrical Properties. Mater. Today Proc. 2015;2:5201–5204. doi: 10.1016/j.matpr.2015.11.021. [DOI] [Google Scholar]
- 78.Hu L., Ren Y., Yang H., Xu Q. Fabrication of 3D Hierarchical MoS2/Polyaniline and MoS2/C Architectures for Lithium-Ion Battery Applications. ACS Appl. Mater. Interfaces. 2014;6:14644–14652. doi: 10.1021/am503995s. [DOI] [PubMed] [Google Scholar]
- 79.Zhang Y., Chen P., Wen F., Huang C., Wang H. Construction of polyaniline/molybdenum sulfide nanocomposite: Characterization and its electrocatalytic performance on nitrite. Ionics. 2016;22:1095–1102. doi: 10.1007/s11581-015-1634-5. [DOI] [Google Scholar]
- 80.Lane B.C.S., Bissessur R., Abd-El-Aziz A.S., Alsaedi W.H., Dahn D.C., McDermott E., Martin A. Exfoliated Nanocomposites Based on Polyaniline and Tungsten Disulfide. In: Yilmaz F., editor. Conducting Polymers. InTech; Rijeka, Croatia: 2016. [Google Scholar]
- 81.Voldman A., Zbaida D., Cohen H., Leitus G., Tenne R. A Nanocomposite of Polyaniline/Inorganic Nanotubes. Macromol. Chem. Phys. 2013;214:2007–2015. doi: 10.1002/macp.201300283. [DOI] [Google Scholar]
- 82.Chang S.-H., Tsai Y.-T., Li G.-A., Jheng S.-L., Kao T.-L., Tuan H.-Y. Uniform silica coating of isoprene-passivated germanium nanowires via Stober method. RSC Adv. 2014;4:40146–40151. doi: 10.1039/C4RA04858J. [DOI] [Google Scholar]
- 83.Verraedt E., Pendela M., Adams E., Hoogmartens J., Martens J.A. Controlled release of chlorhexidine from amorphous microporous silica. J. Control. Release. 2010;142:47–52. doi: 10.1016/j.jconrel.2009.09.022. [DOI] [PubMed] [Google Scholar]
- 84.Pastoriza-Santos I., Pérez-Juste J., Liz-Marzán L.M. Silica-Coating and Hydrophobation of CTAB-Stabilized Gold Nanorods. Chem. Mater. 2006;18:2465–2467. doi: 10.1021/cm060293g. [DOI] [Google Scholar]
- 85.Graf C., Vossen D.L.J., Imhof A., van Blaaderen A. A General Method to Coat Colloidal Particles with Silica. Langmuir. 2003;19:6693–6700. doi: 10.1021/la0347859. [DOI] [PubMed] [Google Scholar]
- 86.Guerrero-Martínez A., Fibikar S., Pastoriza-Santos I., Liz-Marzán L.M., De Cola L. Microcontainers with Fluorescent Anisotropic Zeolite L Cores and Isotropic Silica Shells. Angew. Chem. Int. Ed. 2009;48:1266–1270. doi: 10.1002/anie.200804167. [DOI] [PubMed] [Google Scholar]
- 87.Deng X., Qin P., Luo M., Shao E., Zhao H., Yang X., Wang Y., Shen H., Jiao Z., Wu M. Mesoporous silica coating on carbon nanotubes: Layer-by-layer method. Langmuir. 2013;29:6815–6822. doi: 10.1021/la400690p. [DOI] [PubMed] [Google Scholar]
- 88.Zhao Y., Stejskal J., Wang J. Towards directional assembly of hierarchical structures: Aniline oligomers as the model precursors. Nanoscale. 2013;5:2620–2626. doi: 10.1039/c3nr00145h. [DOI] [PubMed] [Google Scholar]
- 89.Zhao Y., Tomšík E., Wang J., Morávková Z., Zhigunov A., Stejskal J., Trchová M. Self-Assembly of Aniline Oligomers. Chem. Asian J. 2013;8:129–137. doi: 10.1002/asia.201200836. [DOI] [PubMed] [Google Scholar]
- 90.Trchová M., Stejskal J. Polyaniline: The infrared spectroscopy of conducting polymer nanotubes (IUPAC Technical Report) Pure Appl. Chem. 2011;83:1803–1817. doi: 10.1351/PAC-REP-10-02-01. [DOI] [Google Scholar]
- 91.Simić D., Stojanović D.B., Kojović A., Dimić M., Totovski L., Uskoković P.S., Aleksić R. Inorganic fullerene-like IF-WS2/PVB nanocomposites of improved thermo-mechanical and tribological properties. Mater. Chem. Phys. 2016;184:335–344. doi: 10.1016/j.matchemphys.2016.09.060. [DOI] [Google Scholar]
- 92.Shahabuddin S., Sarih N.M., Afzal Kamboh M., Rashidi Nodeh H., Mohamad S. Synthesis of Polyaniline-Coated Graphene Oxide@SrTiO3 Nanocube Nanocomposites for Enhanced Removal of Carcinogenic Dyes from Aqueous Solution. Polymers. 2016;8:305. doi: 10.3390/polym8090305. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 93.Choudhury A. Polyaniline/silver nanocomposites: Dielectric properties and ethanol vapour sensitivity. Sens. Actuators B Chem. 2009;138:318–325. doi: 10.1016/j.snb.2009.01.019. [DOI] [Google Scholar]
- 94.Kang E.T., Neoh K.G., Tan K.L. Polyaniline: A polymer with many interesting intrinsic redox states. Prog. Polym. Sci. 1998;23:277–324. doi: 10.1016/S0079-6700(97)00030-0. [DOI] [Google Scholar]
- 95.Prijic S., Scancar J., Romih R., Cemazar M., Bregar V.B., Znidarsic A., Sersa G. Increased Cellular Uptake of Biocompatible Superparamagnetic Iron Oxide Nanoparticles into Malignant Cells by an External Magnetic Field. J. Membr. Biol. 2010;236:167–179. doi: 10.1007/s00232-010-9271-4. [DOI] [PMC free article] [PubMed] [Google Scholar]
- 96.Hessien M.M., Rashad M.M., Zaky R.R., Abdel-Aal E.A., El-Barawy K.A. Controlling the synthesis conditions for silica nanosphere from semi-burned rice straw. Mater. Sci. Eng. B. 2009;162:14–21. doi: 10.1016/j.mseb.2009.01.029. [DOI] [Google Scholar]
- 97.Schmid A., Fujii S., Armes S.P. Synthesis of Micrometer-Sized Silica-Stabilized Polystyrene Latex Particles. Langmuir. 2005;21:8103–8105. doi: 10.1021/la051687+. [DOI] [PubMed] [Google Scholar]
- 98.Percy M.J., Amalvy J.I., Barthet C., Armes S.P., Greaves S.J., Watts J.F., Wiese H. Surface characterization of vinyl polymer-silica colloidal nanocomposites using X-ray photoelectron spectroscopy. J. Mater. Chem. 2002;12:697–702. doi: 10.1039/b109044p. [DOI] [Google Scholar]
- 99.Alila S., Boufi S., Belgacem M.N., Beneventi D. Adsorption of a Cationic Surfactant onto Cellulosic Fibers I. Surface Charge Effects. Langmuir. 2005;21:8106–8113. doi: 10.1021/la050367n. [DOI] [PubMed] [Google Scholar]
- 100.Sing K.S.W., Everett D.H., Haul R.A.W., Moscou L., Pierotti R.A., Rouquérol J., Siemieniewska T. Reporting Physisorption Data for Gas/Solid Systems with Special Reference to the Determination of Surface Area and Porosity. Pure Appl. Chem. 1982 doi: 10.1351/pac198254112201. [DOI] [Google Scholar]
- 101.Vallet-Regí M., Balas F., Arcos D. Mesoporous Materials for Drug Delivery. Angew. Chem. Int. Ed. 2007;46:7548–7558. doi: 10.1002/anie.200604488. [DOI] [PubMed] [Google Scholar]
- 102.Huang X., Young N.P., Townley H.E. Characterization and Comparison of Mesoporous Silica Particles for Optimized Drug Delivery. Nanomater. Nanotechnol. 2014;4:2. doi: 10.5772/58290. [DOI] [Google Scholar]
- 103.Yan F., Sun L., Li F., Zhuang J., Wang H., Yang W. Mesoporous silica-coated superparamagnetic particles prepared by pseudomorphic transformation and their application in purification of plasmid DNA. J. Nanopart. Res. 2011;13:6613–6620. doi: 10.1007/s11051-011-0569-7. [DOI] [Google Scholar]
- 104.De Araújo A.C.V., de Oliveira R.J., Júnior S.A., Rodrigues A.R., Machado F.L.A., Cabral F.A.O., de Azevedo W.M. Synthesis, characterization and magnetic properties of polyaniline-magnetite nanocomposites. Synth. Met. 2010;160:685–690. doi: 10.1016/j.synthmet.2010.01.002. [DOI] [Google Scholar]
- 105.Lin D.S., Yang S.M. EPR Studies of Poly(o-Phenetidine)-Poly(Styrenesulfonic Acid) and Poly(2-Ethylaniline)-Poly(Styrenesulfonic Acid) Complexes. J. Chin. Chem. Soc. 2004;51:1029–1035. doi: 10.1002/jccs.200400154. [DOI] [Google Scholar]
- 106.Li Y., Zheng J.-L., Feng J., Jing X.-L. Polyaniline micro-/nanostructures: Morphology control and formation mechanism exploration. Chem. Pap. 2013;67:876–890. doi: 10.2478/s11696-013-0347-3. [DOI] [Google Scholar]
- 107.Kahol P.K., Pinto N.J. An EPR investigation of electrospun polyaniline-polyethylene oxide blends. Synth. Met. 2004;140:269–272. doi: 10.1016/S0379-6779(03)00370-9. [DOI] [Google Scholar]
- 108.Krinichnyi V.I. Multi Frequency EPR Spectroscopy of Conjugated Polymers and Their Nanocomposites. CRC Press; Boca Raton, FL, USA: 2016. Multi Frequency EPR Spectroscopy of Conjugated Polymers and Their Nanocomposites. [Google Scholar]
- 109.Green U., Aizenshtat Z., Ruthstein S., Cohen H. Stable radicals formation in coals undergoing weathering: Effect of coal rank. Phys. Chem. Chem. Phys. 2012;14:13046–13052. doi: 10.1039/c2cp41696d. [DOI] [PubMed] [Google Scholar]
- 110.Anand J., Palaniappan S., Sathyanarayana D.N. Electron paramagnetic resonance and conductivity studies on poly(m-toluidine) salts and their bases. Synth. Met. 1994;66:129–134. doi: 10.1016/0379-6779(94)90089-2. [DOI] [Google Scholar]
- 111.Rao P.S., Sathyanarayana D.N. Electron spin resonance spectroscopy and electrical conductivity studies on some polyaniline salts and their bases. Indian J. Chem. 2004;43A:1377–1384. [Google Scholar]
- 112.De Castro E.G., Zarbin A.J.G., de Oliveira H.P., Galembeck A. Novel flexible, freestanding and transparent organic/inorganic hybrid materials formed between polyaniline and polyphosphate gel. Synth. Met. 2004;146:57–62. doi: 10.1016/j.synthmet.2004.06.018. [DOI] [Google Scholar]
- 113.Gupta S.K., Luthra V., Singh R. Electrical transport and EPR investigations: A comparative study for dc conduction mechanism in monovalent and multivalent ions doped polyaniline. Bull. Mater. Sci. 2012;35:787–794. doi: 10.1007/s12034-012-0351-1. [DOI] [Google Scholar]
- 114.Dyson F.J. Electron Spin Resonance Absorption in Metals. II. Theory of Electron Diffusion and the Skin Effect. Phys. Rev. 1955;98:349–359. doi: 10.1103/PhysRev.98.349. [DOI] [Google Scholar]
- 115.Popovych V., Bester M., Stefaniuk I., Kuzma M. Dyson line and modified Dyson line in the EPR measurements. Nukleonika. 2015;60:385. doi: 10.1515/nuka-2015-0068. [DOI] [Google Scholar]