Skip to main content
NCBI home page
BioMed Research International logoLink to BioMed Research International
. 2018 Nov 1;2018:6192059. doi: 10.1155/2018/6192059

Efficient Biocatalytic Synthesis of Chiral Intermediate of Pregabalin Using Immobilized Talaromyces thermophilus Lipase

Xu Ding 1,2, Xiao-Ling Tang 1,2, Ren-Chao Zheng 1,2,✉, Yu-Guo Zheng 1,2
PMCID: PMC6236560  PMID: 30515409

Abstract

A mutant L206F/P207F/L259F of Talaromyces thermophilus lipase (TTL) exhibited high hydrolytic activity towards 2-carboxyethyl-3-cyano-5-methylhexanoic acid ethyl ester (CNDE) for synthesis of (S)-2-carboxyethyl-3-cyano-5-methylhexanoic acid (S-CCMA), a key chiral intermediate of pregabalin. However, low conversion at high CNDE concentration and unreusability of the free TTL mutant restricted its industrial applications. In this study, the TTL mutant was immobilized onto epoxy resin and its catalytic properties for kinetic resolution of CNDE were investigated. Under the optimized conditions, the immobilized lipase exhibited an increased catalytic efficiency even at a CNDE concentration of 3 M with 49.7% conversion and 95% eep. The conversion retained higher than 46.3% even after 10 times repeated use of the immobilized lipase in n-heptane-water biphasic system. These results demonstrated great potential of the immobilized TTL mutant for industrial production of the chiral intermediate of pregabalin.

1. Introduction

Lipases (E.C. 3.1.1.3) have been widely employed in organic synthesis for hydrolysis, alcoholysis, acidolysis, esterification, and transesterification of carboxylic acid esters in aqueous or nonaqueous media [1–4]. It was estimated that about 40% of all biotransformations reported to date were performed with lipase. Apart from their biological significance, they play an important role in industries of pharmaceuticals, cosmetic, leather, foods, perfumery, and fine chemicals with advantages of mild reaction conditions, high stability, and broad substrate specificity [5–10].

However, the use of lipases in their soluble or aggregated forms suffered from deactivation and leakage of proteins in aqueous systems, restricting their industrial applications. Immobilization techniques were regarded as the most promising methods for versatile lipase applications with the advantages of continuous use, easy separation, and prevention of protein or microbial contamination [11–15]. Compared with free enzymes, immobilized enzymes also exhibit improved stability and recyclability [12, 16–23]. Due to the high chemical stability and excellent mechanical strength, covalent binding interactions between enzyme and epoxy carrier can remarkably enhance the stability of free enzyme compared with physical or ionic binding and are employed as one of the most popular immobilization methods to improve catalytic performance [24]. For instance, the fermentation broth of mutant Malassezia globose lipase was directly immobilized onto epoxy resin ECR8285, which showed excellent reusability, stability and activity towards partial glycerides [25]. Rhizopus arrhizus lipase covalently attached to epoxy resin SEPABEADS® EC-EP exhibited much higher operational stability for synthesis of (S)-2-(1-hydroxy-3-butenyl)-5-methylfuran compared to that of free enzyme [26].

Pregabalin is a marketed GABA (γ-aminobutyric acid) analogue for the treatment of epilepsy, neuropathic pain, fibromyalgia, and generalized anxiety disorder in adults [27]. Due to increasing demand of pregabalin, a large number of chemical and enzymatic routes have been developed [28, 29]. (S)-2-Carboxyethyl-3-cyano-5-methylhexanoic acid (S-CCMA) is the key chiral intermediate of pregabalin. Kinetic resolution of 2-carboxyethyl-3-cyano-5-methylhexanoic acid ethyl ester (CNDE) using commercial lipase Lipolase®and Lipozyme TLIM® as biocatalyst seems to be promising approaches to prepare S-CCMA [28]. However, both of them exhibited inferior catalytic efficiency towards CNDE and could not be reused, leading to high cost of the bioprocess.

In our previous work, a mutant L206F/P207F/L259F of TTL was generated by rational design of its crevice-like binding site, which exhibited a 37.23-fold improvement in specific activity for CNDE over the wild-type TTL [30]. However, the free TTL mutant showed low conversion at high CNDE concentration and the unrecyclability of free lipase increased production cost. Herein, in order to realize repeated use of biocatalysts for S-CCMA production, the triple mutant of TTL was immobilized onto the epoxy resin D5730 for kinetic resolution of CNDE. Biochemical properties of the immobilized TTL mutant were characterized, and enantioselective hydrolysis of CNDE by immobilized lipase was investigated. The results indicated that the immobilized TTL mutant exhibited a specific activity of 413.2 U/g and the conversion of CNDE reached 46.3% at a substrate loading of 1 M after 10 reaction cycles, demonstrating its excellent catalytic performance.

2. Materials and Methods

2.1. Materials

The epoxy resin ES-103B was purchased from Nankai Hecheng Technology Co., Ltd (Tianjin, China). The epoxy resin D5730, ECR8204M, D5759, and ECR8204F were purchased from the Purolite Co., Ltd (Huzhou, China). The epoxy resin LX-1000EP was purchased from Sunresin Technology Co., Ltd. Racemic CNDE was prepared according to Zheng et al. [31]. All other chemicals were of analytical grade.

2.2. Expression and Immobilization of TTL Mutant

The TTL mutant gene was overexpressed in Pichia pastoris X33 [30]. Cells were cultivated in YPD medium (2% peptone, 1% yeast extract, 2% glucose, 50 μg mL−1 Zeocin™) at 30°C. The cells were transferred into BMGY medium containing 2% peptone, 1% yeast extract, 1% glycerol, 1.34% yeast nitrogen base, 4×10−5% biotin, and 100 mM potassium phosphate buffer (pH 6.0). The cultivation was performed at 30°C for 22 h and after then the cells were harvested by centrifugation, resuspended and cultured in BMMY media containing 2% peptone, 1% yeast extract, 1.34% yeast nitrogen base, 4×10−5% biotin, and 100 mM potassium phosphate buffer (pH 6.0) at 30°C. Methanol (2%, v/v) was fed to the BMMY media at 24 h interval for 5 days.

The fermentation broth was centrifuged at 8,000 × g for 10 min at 4°C, and the crude enzyme was covalently immobilized onto the epoxy resin. The epoxy resin (1 g) was added to 25 mL of the crude lipase (0.2 mg/mL) under gentle stirring at room temperature. After immobilization, the resins were vacuum filtrated, washed twice by distilled water. Finally, the immobilized lipase was dried at room temperature and stored at 4°C.

2.3. Protein Concentration Assay

The concentration of protein was measured by Coomassie brilliant blue method with bovine serum albumin (BSA) as standard [34]. The immobilization yield was determined using equation:

Immobilization yield (%) = (Pb-Pa) / Pb × 100.

Pb is the amount of protein in supernatant before immobilization and Pa is the amount of protein in supernatant after immobilization.

2.4. Immobilized Lipase Activity Assay

The standard reaction mixture of enzyme activity assay consisted of 10 mL Tris-HCl buffer (100 mM, pH 8.0), 5 mM zinc acetate, 100 mM CNDE, and 0.2 g immobilized lipase. Zinc ions can significantly suppress product inhibition by forming a complex with CCMA that remained suspended in the emulsion and prevented the inactivation of the enzyme in the reactions [35]. The reaction was carried out at 35°C. One unit of immobilized lipase activity was defined as the amount of enzyme required for releasing 1 μmol S-CCMA per minute. The enantiomeric excess of substrate (ees) and product (eep) was measured by gas chromatography (GC) equipped with the FID detector and capillary column Astec CHIRALDEX™ G-TA (30 m × 0.25 mm, 0.25 μm film thickness) using helium as carrier gas [36]. The conversion (c) and enantiomeric ratio (E) were calculated based on ees and eep [37].

2.5. Effect of pH on Lipase Activity and Stability

The effect of pH on activity of immobilized and free TTL mutant was measured using the following buffers at 100 mM: citric acid/sodium citrate buffer (pH 6.0–6.6), Tris-HCl buffer (pH 7.0–8.9), and Gly-NaOH buffer (pH 9.0-10.0).

The pH stability of the lipase was investigated by incubating the immobilized and free TTL mutant in Tris-HCl buffer (100 mM, pH 8.0) for 2 d, 4 d, 6 d, 8 d, 10 d, 15 d, and 20 d at 4°C.

2.6. Effect of Temperature on Lipase Activity and Thermostability

The effect of temperature on lipase activity was investigated at temperatures ranging from 25°C to 70°C under the standard conditions. The reaction was performed at the corresponding temperatures in Tris-HCl buffer (100 mM, pH 8.0). The thermostability of immobilized and free TTL mutant was examined by measuring their residual activity after incubation at 35°C and 50°C, respectively. The initial enzyme activity was taken as 100%. The half-life of the enzyme activity was calculated based on the plots of Ln (RA, relative activity) versus time.

2.7. Kinetic Resolution of CNDE by Immobilized TTL Mutant

The reaction mixture (30 mL) contained 8% (w/v) immobilized lipase, 50-150 mM zinc acetate, and 1-3 M CNDE. The reaction was carried out at 30°C and stirred at 500 rpm, and the pH value was maintained at 7.0 using 4 M NaOH solution by Metrohm titration. The conversion and ee value were determined by GC analysis.

2.8. Reusability of Immobilized TTL Mutant for Hydrolysis of CNDE

Enantioselective hydrolysis of CNDE by immobilized TTL mutant was performed in 30 mL reaction mixture (pH 8.0) containing 8% (w/v) immobilized TTL mutant, 50 mM zinc acetate and 1 M CNDE. The reaction was carried out at 30°C and stirred at 500 rpm. The pH of the reaction was maintained at 7.0 using 4 M NaOH solution by Metrohm titration. The immobilized TLL was recovered by vacuum filtration and then washed twice by water. The recovered immobilized enzyme was dried at room temperature for next cycle.

3. Results and Discussions

3.1. Selection of Epoxy Resins for Immobilization

The effects of epoxy resin carriers on immobilization yield and activity of TTL mutant were shown in Figure 1. When the epoxy resin ES103B and D5730 were used as carriers, more than 75% of lipases in the fermentation broth were immobilized. The TTL mutant immobilized onto epoxy resin D5730 exhibited higher hydrolytic activity than that immobilized onto epoxy resin ES103B. As such, the epoxy resin D5730 with a particle size of 150-300 µm and a pore diameter of 500-600 Å was selected as the carrier for immobilization.

Figure 1.

Figure 1

Open in a new tab

The effect of different resins on immobilization yield and activity of immobilized enzyme. Epoxy resin was directly added to the crude fermentation lipase under gentle stirring at room temperature. The reaction mixture consisted of 10 mL Tris-HCl buffer (100 mM, pH 8.0), 5 mM zinc acetate, 100 mM CNDE, and 0.2 g immobilized lipase. The reaction was performed at 30°C and stirred at 500 rpm. Symbols: filled square, relative activity of immobilized lipase; bar, immobilization yield of epoxy resin.

3.2. Immobilization of TTL on Epoxy Resin D5730

In previous works, the immobilization of enzymes onto epoxy supports was preferentially carried out at alkaline pH (around 10) to promote the deprotonation of terminal amino group (pKa=6.5) and amino groups of lysine residues (pKa=10.5). However, we found that initial pH of the buffer had no significant effect on immobilization efficiency, which was in accordance with immobilization of lipase SMG1 [25]. Moreover, the free TTL mutant was unstable at pH 10.0. Therefore, the crude TTL mutant from fermentation broth was directly immobilized onto the epoxy resin D5730. The effect of protein/epoxy resin ratio on TTL mutant immobilization was investigated. As shown in Figure 2, the maximum loading and highest activity of immobilized lipase was achieved at protein/epoxy resin ratio of 30 mg/g, and the loading of enzyme reached 23.5 mg per gram of epoxy resin. Under this condition, the specific activity of immobilized lipase reached 413.2 U/g carriers with an immobilization yield of 78.3%. Notably, enantioselectivity of the immobilized TTL mutant was as high as that of the free TTL mutant (E > 120).

Figure 2.

Figure 2

Open in a new tab

Effect of protein/epoxy resin ratio on immobilization yield and activity of the immobilized TTL mutant. The epoxy resin D5730 was directly added to the crude lipase with different protein/epoxy resin ratio under gentle stirring at room temperature. The reaction was performed at 30°C and stirred at 500 rpm using immobilized enzyme with 100 mM CNDE and 5 mM zinc acetate in Tris-HCl buffer. Symbols: filled square, relative activity of immobilized enzyme; square, protein loading.

3.3. Effect of pH on Lipase Activity and Stability

The pH is an important factor in maintaining the proper conformation of a protein [38]. Effects of pH on hydrolytic activity of the free and immobilized TTL mutant were shown in Figure 3. The highest activity of immobilized enzyme was observed around pH 8.0, which was consistent with the free TTL mutant. Moreover, the immobilized TTL mutant displayed higher activity than the free lipase at pH 8.0-9.0, indicating that the immobilized lipase was able to tolerate a broader range of pH.

Figure 3.

Figure 3

Open in a new tab

Effect of pH on activity of immobilized and free TTL mutant. The reactions were all carried out at 35°C and the enzyme activities were determined in buffers with different pHs: citric acid/sodium citrate (pH 6.0-6.6), Tris-HCl (pH 7.0-9.0), and Gly-NaOH (9.6-10.0) which contained 100 mM CNDE and 5 mM zinc acetate. Symbols: filled square, immobilized TTL mutant; filled circle, free TTL mutant.

The pH stability of the free and immobilized TTL mutant was performed in Tris-HCl buffer (100 mM, pH 8.0). Both of them showed excellent stability under the optimal pH 8.0. The immobilized enzyme and free enzyme remained 96% of their initial activity after 20 d incubation at 4°C.

3.4. Effect of Temperature on Lipase Activity and Thermostability

The effect of temperature on activity of immobilized lipase was investigated at a temperature range from 25°C to 70°C. As shown in Figure 4(a), the optimal temperature of the immobilized TTL mutant was 60°C, which was 25°C higher than that of the free TTL mutant. Simultaneously, the immobilized lipase showed broad temperature stability at 55-65°C and retained 75% of its activity at 65°C. The reason for higher activity of the immobilized enzyme over a wider range of temperature may lie in the limited conformational mobility of the enzyme molecules at high temperature, preventing it from inactivation [38].

Figure 4.

Figure 4

Open in a new tab

Effect of temperature on activity (a) and thermostability (b) of immobilized and free TTL mutant. The reaction mixture (pH 8.0) was composed of 100 mM Tris-HCl, 100 mM CNDE and 5 mM zinc acetate. Symbols: filled triangle, free TTL mutant; filled diamond, immobilized TTL mutant; filled square, immobilized TTL mutant at 50°C; filled circle, free TTL mutant at 50°C; square, immobilized TTL mutant at 35°C; circle, free TTL mutant at 35°C.

The thermostability of the immobilized enzyme was investigated by measuring its residual activity after incubation for various periods of time at 35°C and 50°C. As shown in Figure 4(b), after 9 h incubation, the residual activity of the immobilized and free TTL was 89.4% and 68.8% of their initial activity at 50°C, respectively. Both of the immobilized and free TTL mutant remained over 94% of their initial activity after 72 h at 35°C. The half-lives of immobilized and free TTL mutant were determined to be 35.7 h and 24.7 h at 50°C, respectively. The stabilization factor of immobilized TTL mutant ranged from 0.9 to 1.1[39]. The changed optimal temperature and thermostability of immobilized enzyme may attribute to the rigid structure of protein that covalently attached onto the epoxy resin after immobilization [25, 26]. Therefore, the immobilized TTL mutant exhibited higher temperature tolerance for CNDE hydrolysis.

3.5. Kinetic Resolution of CNDE by Immobilized Lipase

Efficient and enantioselective hydrolysis of CNDE is the most crucial step in chemoenzymatic synthesis of pregabalin [32, 36, 40]. Although the catalytic efficiency of TTL mutant was 89.4 times higher than the commercial lipase Lipolase®, the conversion was low when concentration of CNDE exceeded 1.0 M [30]. The concentration of S-CCMA reached 492 mM at a substrate loading of 1 M after 1 h and 993 mM at 2 M CNDE after 2 h, respectively (Figure 5). Notably, S-CCMA was produced with 49.7% conversion and > 95% eep at a substrate loading up to 3 M after 3 h. Moreover, the reaction time for kinetic resolution of 3 M CNDE by immobilized TTL mutant was shortened from 24 h to 3 h compared with the bioprocess using Liploase® as biocatalysts [28]. The efficient enantioselective hydrolysis of CNDE by the immobilized TTL mutant demonstrated its potential for industrial production of pregabalin precursor (Table 1).

Figure 5.

Figure 5

Open in a new tab

Progress curves of kinetic resolution of CNDE catalyzed by immobilized TTL mutant in Tris-HCl buffer. Symbols: filled square, 1 M CNDE; filled circle, 2 M CNDE; filled triangle, 3 M CNDE; square, eep of S-CCMA.

Table 1.

Comparison of CNDE resolution between immobilized TTL mutant and other lipases.

Enzyme source Substrate concentration (M) Conversion Space-time yield Reference
(%) (g/L/h)
Thermomyces lanuginosus lipase 3 47.5 12.9 [28]
Thermomyces lanuginosus lipase 3 45.2 12.8 [32]
Pseudomonas esterase 0.5 47.7 7.7 [33]
Talaromyces thermophilus lipase 3 49.7 112.8 This work
Open in a new tab

3.6. Reusability of the Immobilized Lipase for Hydrolysis of CNDE

Except for activity and enantioselectivity, reusability of immobilized enzyme was another important criterion, especially in industrial application [26]. To evaluate the repeated use of the immobilized TTL mutant, the reaction was firstly carried out in aqueous medium with a substrate loading of 1 M. After the reaction was terminated, the immobilized TTL mutant was filtrated under vacuum. As shown in Figure 6, the conversion of CNDE was only 37.5% after 6 times repeated use of immobilized TTL mutant. However, when the biotransformation was performed in n-heptane-water (2:8) biphasic system, the conversion was higher than 46.3% after 10 cycles. The results indicated that the immobilized lipase possessed good operational stability in nonaqueous medium.

Figure 6.

Figure 6

Open in a new tab

Reusability of immobilized TTL mutant for hydrolysis of CNDE in aqueous and n-heptane-water (2:8) biphasic system. The reaction mixture was composed of Tris-HCl buffer or n-heptane-water (2:8), 1.0 M CNDE, and 50 mM zinc acetate. The reaction was carried out at 30°C and 500 rpm with mechanical stirring. Symbols: bar, immobilized lipase in aqueous medium; filled bar, immobilized TTL lipase in n-heptane-water (2:8) biphasic system.

According to the previous reports, immobilization of enzyme via covalent attachment usually maintained its inherent activity even under harsh conditions [24]. As the substrate CNDE is water insoluble oil, when the reaction was carried out in aqueous system, remaining (R)-CNDE was adsorbed on the surface of epoxy resin. With repeated use of the immobilized lipase, more and more unreacted CNDE was accumulated, leading to increased mass transfer resistance and lower catalytic efficiency in the following recycles, while in the n-heptane-water biphasic system, unhydrolyzed CNDE was dissolved into the organic phase and the mass transfer problem was thus resolved. However, the conversion of CNDE was only 36.8% after 11 cycles even in biphasic system due to agglomeration of immobilized enzyme caused by viscous unreacted substrate.

4. Conclusion

In our study, a mutant L206F/P207F/L259F of T. thermophilus lipase was efficiently immobilized onto epoxy resin D5730 and the catalytic properties of the immobilized lipase were characterized. It exhibited excellent catalytic efficiency even at high CNDE concentration of 3 M and showed good reusability in n-heptane-water biphasic system. These findings suggested that the immobilized lipase was a robust biocatalyst for industrial production of chiral intermediate of pregabalin.

Acknowledgments

This work was financially supported by the National High Technology Research and Development Program of China (No. 2012AA022201), the Key Scientific and Technology Programs of Zhejiang Province (No. 2012C03005-2), and the Natural Science Foundation of Zhejiang Province (No. Z4090612).

Data Availability

The data used to support the findings of this study are available from the corresponding author upon request.

Conflicts of Interest

The authors have no financial conflicts of interest to declare.

References

  • 1.Seddigi Z. S., Malik M. S., Ahmed S. A., Babalghith A. O., Kamal A. Lipases in asymmetric transformations: Recent advances in classical kinetic resolution and lipase–metal combinations for dynamic processes. Coordination Chemistry Reviews. 2017;348:54–70. doi: 10.1016/j.ccr.2017.08.008. [DOI] [Google Scholar]
  • 2.Padkina M. V., Sambuk E. V. Prospects for the Application of Yeast Display in Biotechnology and Cell Biology (Review) Applied Biochemistry and Microbiology. 2018;54(4):337–351. doi: 10.1134/S0003683818040105. [DOI] [Google Scholar]
  • 3.Javed S., Azeem F., Hussain S., et al. Bacterial lipases: a review on purification and characterization. Progress in Biophysics & Molecular Biology. 2018;132:23–34. doi: 10.1016/j.pbiomolbio.2017.07.014. [DOI] [PubMed] [Google Scholar]
  • 4.Sánchez D. A., Tonetto G. M., Ferreira M. L. Burkholderia cepacia lipase: A versatile catalyst in synthesis reactions. Biotechnology and Bioengineering. 2018;115(1):6–24. doi: 10.1002/bit.26458. [DOI] [PubMed] [Google Scholar]
  • 5.Anobom C. D., Pinheiro A. S., De-Andrade R. A., et al. From Structure to Catalysis: Recent Developments in the Biotechnological Applications of Lipases. BioMed Research International. 2014;2014:11. doi: 10.1155/2014/684506.684506 [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 6.Egorova K. S., Gordeev E. G., Ananikov V. P. Biological Activity of Ionic Liquids and Their Application in Pharmaceutics and Medicine. Chemical Reviews. 2017;117(10):7132–7189. doi: 10.1021/acs.chemrev.6b00562. [DOI] [PubMed] [Google Scholar]
  • 7.Poterała M., Dranka M., Borowiecki P. Chemoenzymatic Preparation of Enantiomerically Enriched (R)-(–)-Mandelic Acid Derivatives: Application in the Synthesis of the Active Agent Pemoline. European Journal of Organic Chemistry. 2017;2017(16):2290–2304. doi: 10.1002/ejoc.201700161. [DOI] [Google Scholar]
  • 8.Kumar A., Khan A., Malhotra S., et al. Synthesis of macromolecular systems: Via lipase catalyzed biocatalytic reactions: Applications and future perspectives. Chemical Society Reviews. 2016;45(24):6855–6887. doi: 10.1039/C6CS00147E. [DOI] [PubMed] [Google Scholar]
  • 9.Contesini F. J., Lopes D. B., MacEdo G. A., Nascimento M. D. G., Carvalho P. D. O. Aspergillus sp. lipase: potential biocatalyst for industrial use. Journal of Molecular Catalysis B: Enzymatic. 2010;67(3-4):163–171. doi: 10.1016/j.molcatb.2010.07.021. [DOI] [Google Scholar]
  • 10.Contesini F. J., de Oliveira Carvalho P. Esterification of (RS)-Ibuprofen by native and commercial lipases in a two-phase system containing ionic liquids. Tetrahedron: Asymmetry. 2006;17(14):2069–2073. doi: 10.1016/j.tetasy.2006.07.020. [DOI] [Google Scholar]
  • 11.Sankaran R., Show P. L., Chang J.-S. Biodiesel production using immobilized lipase: feasibility and challenges. Biofuels, Bioproducts and Biorefining. 2016;10(6):896–916. doi: 10.1002/bbb.1719. [DOI] [Google Scholar]
  • 12.Sun J., Chen Y., Sheng J., Sun M. Immobilization of Yarrowia lipolytica lipase on macroporous resin using different methods: characterization of the biocatalysts in hydrolysis reaction. BioMed Research International. 2015;2015:7. doi: 10.1155/2015/139179.139179 [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 13.Zou S.-P., Wang Z.-C., Qin C., Zheng Y.-G. Covalent immobilization of Agrobacterium radiobacter epoxide hydrolase on ethylenediamine functionalised epoxy supports for biocatalytical synthesis of (R)-epichlorohydrin. Biotechnology Letters. 2016;38(9):1579–1585. doi: 10.1007/s10529-016-2135-y. [DOI] [PubMed] [Google Scholar]
  • 14.Cazaban D., Wilson L., Betancor L. Lipase immobilization on siliceous supports: Application to synthetic reactions. Current Organic Chemistry. 2017;21(12):85–92. [Google Scholar]
  • 15.Vaghari H., Jafarizadeh-Malmiri H., Mohammadlou M., et al. Application of magnetic nanoparticles in smart enzyme immobilization. Biotechnology Letters. 2016;38(2):223–233. doi: 10.1007/s10529-015-1977-z. [DOI] [PubMed] [Google Scholar]
  • 16.Brady D., Jordaan J. Advances in enzyme immobilisation. Biotechnology Letters. 2009;31(11):1639–1650. doi: 10.1007/s10529-009-0076-4. [DOI] [PubMed] [Google Scholar]
  • 17.Sheldon R. A., Van Pelt S. Enzyme immobilisation in biocatalysis: why, what and how. Chemical Society Reviews. 2013;42(15):6223–6235. doi: 10.1039/c3cs60075k. [DOI] [PubMed] [Google Scholar]
  • 18.Branco R. V., Gutarra M. L. E., Guisan J. M., Freire D. M. G., Almeida R. V., Palomo J. M. Improving the thermostability and optimal temperature of a lipase from the hyperthermophilic archaeon pyrococcus furiosus by covalent immobilization. BioMed Research International. 2015;2015:8. doi: 10.1155/2015/250532.250532 [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 19.Bezerra C. S., De Farias Lemos C. M. G., De Sousa M., Gonçalves L. R. B. Enzyme immobilization onto renewable polymeric matrixes: Past, present, and future trends. Journal of Applied Polymer Science. 2015;132(26) [Google Scholar]
  • 20.Kim K. H., Lee O. K., Lee E. Y. Nano-immobilized biocatalysts for biodiesel production from renewable and sustainable resources. Journal of Catalysis. 2018;8(2) [Google Scholar]
  • 21.Shuai W., Das R. K., Naghdi M., Brar S. K., Verma M. A review on the important aspects of lipase immobilization on nanomaterials. Biotechnology and Applied Biochemistry. 2017;64(4):496–508. doi: 10.1002/bab.1515. [DOI] [PubMed] [Google Scholar]
  • 22.Chakraborty S., Rusli H., Nath A., et al. Immobilized biocatalytic process development and potential application in membrane separation: A review. Critical Reviews in Biotechnology. 2016;36(1):43–48. doi: 10.3109/07388551.2014.923373. [DOI] [PubMed] [Google Scholar]
  • 23.Da Silva V. C. F., Contesini F. J., De Oliveira Carvalho P. Enantioselective behavior of lipases from Aspergillus niger immobilized in different supports. Journal of Industrial Microbiology and Biotechnology. 2009;36(7):949–954. doi: 10.1007/s10295-009-0573-4. [DOI] [PubMed] [Google Scholar]
  • 24.Mateo C., Grazu V., Palomo J. M., Lopez-Gallego F., Fernandez-Lafuente R., Guisan J. M. Immobilization of enzymes on heterofunctional epoxy supports. Nature Protocols. 2007;2(5):1022–1033. doi: 10.1038/nprot.2007.133. [DOI] [PubMed] [Google Scholar]
  • 25.Li X., Li D., Wang W., Durrani R., Yang B., Wang Y. Immobilization of SMG1-F278N lipase onto a novel epoxy resin: Characterization and its application in synthesis of partial glycerides. Journal of Molecular Catalysis B: Enzymatic. 2016;133:154–160. doi: 10.1016/j.molcatb.2016.08.011. [DOI] [Google Scholar]
  • 26.Yang G., Wu J., Xu G., Yang L. Enantioselective resolution of 2-(1-hydroxy-3-butenyl)-5-methylfuran by immobilized lipase. Applied Microbiology and Biotechnology. 2009;81(5):847–853. doi: 10.1007/s00253-008-1713-x. [DOI] [PubMed] [Google Scholar]
  • 27.Frampton J. E. Pregabalin: a review of its use in adults with generalized anxiety disorder. CNS Drugs. 2014;28(9):835–854. doi: 10.1007/s40263-014-0192-0. [DOI] [PubMed] [Google Scholar]
  • 28.Martinez C. A., Hu S., Dumond Y., Tao J., Kelleher P., Tully L. Development of a chemoenzymatic manufacturing process for Pregabalin. Organic Process Research & Development. 2008;12(3):392–398. doi: 10.1021/op7002248. [DOI] [Google Scholar]
  • 29.Pierluigi R., Peter M. Process for the preparation of pregnanes. Macromolecules . 2014;188(2):695–704. [Google Scholar]
  • 30.Ding X., Zheng R.-C., Tang X.-L., Zheng Y.-G. Engineering of Talaromyces thermophilus lipase by altering its crevice-like binding site for highly efficient biocatalytic synthesis of chiral intermediate of Pregablin. Bioorganic Chemistry. 2018;77:330–338. doi: 10.1016/j.bioorg.2018.01.018. [DOI] [PubMed] [Google Scholar]
  • 31.Zheng R.-C., Wang T.-Z., Fu D.-J., Li A.-P., Li X.-J., Zheng Y.-G. Biocatalytic synthesis of chiral intermediate of pregabalin with high substrate loading by a newly isolated Morgarella morganii ZJB-09203. Applied Microbiology and Biotechnology. 2013;97(11):4839–4847. doi: 10.1007/s00253-013-4810-4. [DOI] [PubMed] [Google Scholar]
  • 32.Li X.-J., Zheng R.-C., Ma H.-Y., Huang J.-F., Zheng Y.-G. Key residues responsible for enhancement of catalytic efficiency of Thermomyces lanuginosus lipase Lip revealed by complementary protein engineering strategy. Journal of Biotechnology. 2014;188:29–35. doi: 10.1016/j.jbiotec.2014.08.004. [DOI] [PubMed] [Google Scholar]
  • 33.Xu F., Chen S., Xu G., Wu J., Yang L. Discovery and expression of a Pseudomonas sp. esterase as a novel biocatalyst for the efficient biosynthesis of a chiral intermediate of pregabalin. Biotechnology and Bioprocess Engineering. 2015;20(3):473–487. doi: 10.1007/s12257-015-0069-1. [DOI] [Google Scholar]
  • 34.Bradford M. M. A rapid and sensitive method for the quantitation of microgram quantities of protein utilizing the principle of protein dye binding. Analytical Biochemistry. 1976;72(1-2):248–254. doi: 10.1016/0003-2697(76)90527-3. [DOI] [PubMed] [Google Scholar]
  • 35.Dunn P. J., Wells A. S. Green Chemistry in the Pharmaceutical Industry. Wiley-VCH; 2010. [Google Scholar]
  • 36.Li X.-J., Zheng R.-C., Ma H.-Y., Zheng Y.-G. Engineering of Thermomyces lanuginosus lipase Lip: Creation of novel biocatalyst for efficient biosynthesis of chiral intermediate of Pregabalin. Applied Microbiology and Biotechnology. 2014;98(6):2473–2483. doi: 10.1007/s00253-013-5136-y. [DOI] [PubMed] [Google Scholar]
  • 37.Rakels J. L. L., Straathof A. J. J., Heijnen J. J. A simple method to determine the enantiomeric ratio in enantioselective biocatalysis. Enzyme and Microbial Technology. 1993;15(12):1051–1056. doi: 10.1016/0141-0229(93)90053-5. [DOI] [PubMed] [Google Scholar]
  • 38.Jiang X.-P., Lu T.-T., Liu C.-H., et al. Immobilization of dehydrogenase onto epoxy-functionalized nanoparticles for synthesis of (R)-mandelic acid. International Journal of Biological Macromolecules. 2016;88:9–17. doi: 10.1016/j.ijbiomac.2016.03.031. [DOI] [PubMed] [Google Scholar]
  • 39.Bortone N., Fidaleo M., Moresi M. Immobilization/stabilization of acid urease on Eupergit® supports. Biotechnology Progress. 2012;28(5):1232–1244. doi: 10.1002/btpr.1598. [DOI] [PubMed] [Google Scholar]
  • 40.Zheng R.-C., Ruan L.-T., Ma H.-Y., Tang X.-L., Zheng Y.-G. Enhanced activity of Thermomyces lanuginosus lipase by site-saturation mutagenesis for efficient biosynthesis of chiral intermediate of pregabalin. Biochemical Engineering Journal. 2016;113:12–18. doi: 10.1016/j.bej.2016.05.007. [DOI] [Google Scholar]

Associated Data

This section collects any data citations, data availability statements, or supplementary materials included in this article.

Data Availability Statement

The data used to support the findings of this study are available from the corresponding author upon request.

Articles from BioMed Research International are provided here courtesy of Wiley

RESOURCES