Skip to main content
PMC home page
Molecules logoLink to Molecules
. 2020 Feb 10;25(3):759. doi: 10.3390/molecules25030759

Stabilizing the Oil-in-Water Emulsions Using the Mixtures of Dendrobium Officinale Polysaccharides and Gum Arabic or Propylene Glycol Alginate

Bo Wang 1, Haiyan Tian 1, Dong Xiang 1,2,*
PMCID: PMC7037464  PMID: 32050560

Abstract

Coconut oil-in-water emulsions were prepared using three polysaccharides: Dendrobium officinale polysaccharide (DOP), propylene glycol alginate (PGA), gum arabic (GA) and their polysaccharide complexes as emulsifiers. The effects of the ratio of the compounded polysaccharides on their apparent viscosity and interfacial activity were explored in this study. The average particle size, zeta potential, microstructure, rheological properties, and physical stability of the emulsions prepared with different compound-polysaccharides were studied. The results showed that mainly DOP contributed to the apparent viscosity of the compound-polysaccharide, while the interfacial activity and zeta potential were mainly influenced by PGA or GA. Emulsions prepared with compound-polysaccharides exhibited smaller average particle sizes, and microscopic observations showed smaller droplets and less droplet aggregation. In addition, the stability analysis of emulsions by a dispersion analyzer LUMiSizer showed that the emulsion prepared by compounding polysaccharides had better physical stability. Finally, all of the above experimental results showed that the emulsions prepared by PGA:DOP = 2:8 (total concentration = 1.5 wt%) and 2.0% GA + 1.5% DOP were the most stable.

Keywords: Dendrobium officinale polysaccharides, propylene glycol alginate, gum arabic, coconut oil-in-water emulsion

1. Introduction

Emulsions are applied in various fields including food, cosmetics, pharmaceuticals, petrochemicals, and agricultural products [1,2,3,4]. An emulsion is a thermodynamically unstable system of two immiscible liquids. Emulsions are categorized into two types: oil-in-water (O/W) and water-in-oil (W/O) emulsions [1,5]. Oil-in-water emulsions are extensively used in food products including milk, beverages, sauces, etc., and oil-in-water emulsions are utilized for delivering lipophilic bioactive compounds such as vitamins and antioxidants [1,6,7,8]. The stability of the emulsions is limited by different phenomena including coalescence, flocculation, lactation, and Ostwald ripening [2,3,4,5,7]. The stability of the emulsions can be improved by adding emulsifiers and stabilizers. Polysaccharides are often used as stabilizers and thickeners in the food industry [2,9]. Polysaccharides, when added to oil-in-water emulsions, increase the viscosity of the aqueous phase, enhance the spatial repulsive force and electrostatic repulsion between the oil droplets, and alter the rheological properties of the emulsion [3,5,8,9,10]. In recent years, scientists have studied the emulsification properties of many natural polysaccharides such as seaweed polysaccharides [10], pectin [8], spruce galactoglucomannans [11], orchid-root polysaccharides [12], basil-seed polysaccharides [13], etc.

Dendrobium officinale, a precious Chinese herbal plant, is distributed mainly in tropical and subtropical regions [14,15]. Polysaccharides from Dendrobium officinale have demonstrated many biological activities including antioxidant, antitumor, hypoglycemic, and immunomodulatory activities [15,16,17,18,19,20,21,22,23]. Previous studies have shown that Dendrobium candidum polysaccharide is mainly composed of mannose and glucose, and its molecular weight is between 178 KDa and 394 KDa [14,18,22]. Unfortunately, no research has been conducted on the emulsification properties of Dendrobium officinale polysaccharides. Propylene glycol alginate (PGA) is a derivative of propylene oxide and alginic acid; PGA is a linear polysaccharide with 50–85% of esterified carboxyl groups [24,25,26]. PGA is widely used in the food industry as a viscosity enhancer and stabilizer [27,28,29,30]. Gum arabic (GA), a natural complex polysaccharide with good emulsifying properties and high water-solubility, is widely used as an emulsifier in the food industry [31,32]. Gum arabic is composed of arabinogalactan (AG), arabinogalactan protein (AGP), and glycoprotein (GP). The emulsifying property of GA is majorly contributed by AGP [33,34,35,36,37].

PGA contains numerous esterified carboxyl groups, but its hydrophilicity is weak. DOP is a highly hydrophilic natural polysaccharide, so the compound polysaccharide of DOP and PGA is likely to be a good emulsifier. Additionally, GA possesses high hydrophilicity and low viscosity. As an emulsifier, a high quantity of GA is required to prepare a stable emulsion [38,39]. However, DOP can greatly increase the viscosity of the continuous phase, so the complex polysaccharides of GA and DOP can exert good emulsifying effects. In this study, an oil-in-water emulsion was prepared using a compound of Dendrobium officinale polysaccharide, GA or PGA as an emulsifier, and coconut oil as an internal dispersed phase. The apparent viscosity and interfacial tension of the mixed polysaccharides were investigated, and the stability of the water–oil emulsions was studied. The emulsified concentration of the compound polysaccharide was investigated to prepare a stable emulsion. The particle size distribution, zeta potential, microstructure, and rheological properties of the oil-in-water emulsion were measured. This study provides a better application of Dendrobium officinale polysaccharides as an emulsifier in natural functional emulsions.

2. Results and Discussion

2.1. Apparent Viscosity of Polysaccharides

In Figure 1A, the apparent viscosity of PGA and DOP increased while increasing the concentration, which is a common feature of macromolecular polysaccharide aqueous solutions. When the concentration of the polysaccharide molecule was increased, the interaction between the polysaccharide molecules increased, which resulted in an increase in the viscosity of the polysaccharide solution [40]. However, no significant change has been observed in the viscosity of the aqueous solution of GA at a concentration of 0.1–1%, because GA has good water solubility and low viscosity [32], and a significant increase in the viscosity can be observed only at a concentration of 10% or more. In addition, Figure 1B shows the effect of the ratio of the compound-polysaccharide (total concentration was 1%) on its viscosity. The viscosity of the compound-polysaccharide was closely related to the ratio of DOP and PGA or the ratio of DOP and GA. Additionally, the content of DOP could significantly affect the viscosity of the two polysaccharides. For PGA:DOP = 2:8 and GA DOP = 2:8, the viscosities of the two polysaccharides were the largest. These results indicated that the apparent viscosity of the polysaccharides in aqueous solutions was primarily provided by DOP.

Figure 1.

Figure 1

Open in a new tab

(A) Relationship between apparent viscosity and concentration of three polysaccharides. (B) Apparent viscosity of the compound polysaccharides at different ratios (total concentration was 1 wt%); a–e indicate significant differences (p < 0.01).

2.2. Interfacial Tension of the Polysaccharides

The interfacial properties of the emulsifier reflect its emulsion stabilizing property [10]. In Figure 2A, compared to the interfacial tension between coconut oil and water (23.46 mN/m) [6,41], the interfacial tension of the three polysaccharide aqueous solutions was significantly reduced. The interfacial tension of the polysaccharide solution decreased while increasing the concentration of the polysaccharide; previous studies that reported that the polysaccharide molecules were adsorbed on the oil–water interface agreed with the above observation [6,42,43]. Interestingly, the interfacial tension of PGA was the lowest at a concentration of 0.25%, and the interfacial tension of DOP was the lowest at a concentration of 0.75%, but the interfacial tension of GA continued to decrease within a concentration range of 0.1–1%. This phenomenon indicates that the adsorption amount at the oil–water interface gradually increases while increasing the concentration of the emulsifier, and when the adsorption amount is saturated, it reaches critical micellar concentration (CMC); at this time, the interfacial tension reaches a steady-state [44,45]. Furthermore, the ability of GA to reduce the interfacial tension was the best of the three polysaccharide forces, which was due to the low molecular weight of GA and the proteins in GA. Compared to large molecular polysaccharides, small molecular polysaccharides and surface hydrophobic proteins could be adsorbed to the oil–water interface faster [38,43]. In Figure 2B, the interfacial activity of the compound-polysaccharides mainly depended upon the contents of GA and PGA, which was the opposite to their apparent viscosities. The surface hydrophobicity of the compound-polysaccharides was mainly provided by PGA and GA, and for PGA:DOP = 8:2 and GA:DOP = 8:2, the compound polysaccharide exhibited the smallest interfacial tension. It is interesting, however, that when PGA:DOP = 5:5 and GA:DOP = 4:6, their interfacial tension was the largest. This shows that the value of interfacial tension does not change regularly with the proportion of PGA or GA in the complex polysaccharide. This might be when PGA:DOP or GA:DOP was in a certain ratio; the emulsifier molecules interacted with each other and led to reduced group exposure.

Figure 2.

Figure 2

Open in a new tab

(A) Relationship between the interfacial tension (IFT) and concentration of three polysaccharides. (B) Interfacial tension (IFT) of the compound polysaccharides at different ratios (total concentration was 1 wt%), a–d indicate significant differences (p < 0.01).

2.3. The Particle Size Distribution of the Emulsions

The particle size distribution of the emulsion can reflect the droplet flocculation and aggregation [43]. In Figure 3, the particle size distribution curves of all emulsions were single-peaked, which indicated that all emulsions formed uniform droplets. The emulsion prepared by PGA alone exhibited the largest average particle size. As described in Section 3.2, PGA displayed the weakest ability to reduce interfacial tension, and it was not effectively adsorbed on the droplet surface [46]. In contrast, the average particle size of the emulsion prepared by GA alone was smaller than the PGA due to the excellent adsorption rate of GA [37]. However, the particle size of the emulsion prepared by DOP alone was the smallest of the three polysaccharides, which might benefit from the high viscosity of DOP, the limited movement of the droplets, and re-agglomeration [2]. When PGA was mixed with DOP, the average particle size of the emulsion was significantly reduced. For PGA:DOP = 2:8, the average particle size was the smallest (8.356 ± 0.061 μm). Meanwhile, for GA:DOP = 2:8, the average particle size was 11.768 ± 0.015 μm. This result validates our conjecture that DOP was highly hydrophilic, while PGA and GA contained hydrophobic groups. When DOP was mixed with PGA or GA, a mixed emulsifier containing both hydrophilic and hydrophobic groups was formed [41]. This mixed emulsifier easily formed stable emulsions.

Figure 3.

Figure 3

Open in a new tab

(A) Particle size distribution of emulsions prepared by compounding polysaccharides of PGA and DOP as emulsifiers (total emulsifier concentration was 1 wt%); (B) Particle size distribution of emulsions prepared by compounding polysaccharides of GA and DOP as emulsifiers (total emulsifier concentration was 1 wt%); (C) The average particle size of emulsions prepared by compounding polysaccharides of PGA and DOP as emulsifiers (total emulsifier concentration was 1 wt%); (D) The average particle size of emulsions prepared by compounding polysaccharides of GA and DOP as emulsifiers (total emulsifier concentration was 1 wt%), a–g indicate significant differences (p < 0.01).

2.4. Zeta Potential

Zeta potential characterizes the surface charge of the droplets and reflects the repulsive force between the emulsion droplets [47]. According to Figure 4, the zeta potential of all emulsions was negative, and the zeta potential value was quite high. Previous studies have reported that both PGA and GA contain negative charges [37,41,42]. The emulsion prepared by DOP alone exhibited the smallest amount of surface charge, while the amount of charge of the emulsion prepared by compounding polysaccharides depended upon the ratio of PGA or GA. For PGA:DOP = 8:2, the emulsion displayed the largest zeta potential value, but for GA:DOP = 8:2, the zeta potential value of the emulsion was second only to that of the emulsion prepared by GA alone. This phenomenon showed that the compound polysaccharides could be used as emulsifiers to provide better electrostatic repulsion between emulsion droplets.

Figure 4.

Figure 4

Open in a new tab

(A) The zeta potential of emulsions prepared by compounding polysaccharides of PGA and DOP as emulsifiers (total emulsifier concentration was 1 wt%); (B) The zeta potential of emulsions prepared by compounding polysaccharides of GA and DOP as emulsifiers (total emulsifier concentration was 1 wt%), a–f indicate significant differences (p < 0.01).

2.5. Fluorescent Microstructure of Emulsions

Figure 5 shows the microstructure of the emulsions under a fluorescence microscope. The emulsion prepared by 1% GA alone and the emulsion prepared by 1% PGA contained larger droplets and large amounts of aggregation, which agreed with their average particle size in Section 3.3. However, compared to the emulsion prepared by 1% GA alone or 1% PGA alone, the emulsion prepared by 1% DOP alone displayed more small-sized droplets and less aggregation. Two main types of repulsions prevent the aggregation of emulsion droplets: steric and electrostatic repulsion [38,48]. Polysaccharides can increase the viscosity of the aqueous phase and strengthen the steric repulsion of the emulsion [49]. The emulsion stabilized by DOP alone possessed the smallest zeta potential, but small droplets (from Section 3.4), indicating that the high viscosity of the DOP aqueous phase prevented the aggregation of the droplets. For the emulsion prepared by the compound polysaccharides, the microstructure of emulsions indicated that the droplet size and degree of aggregation of the emulsion were highly depended upon the ratio of PGA:DOP or GA:DOP. The higher the proportion of PGA or GA in the compound polysaccharide, the larger the emulsion droplets, and the more severe the aggregation of the emulsion droplets, suggesting that the viscosity was a crucial factor for maintaining the stability of the emulsion under this condition.

Figure 5.

Figure 5

Figure 5

Open in a new tab

The microstructure of emulsions prepared by compounding polysaccharides of PGA and DOP or compounding polysaccharides of GA and DOP as emulsifiers (total emulsifier concentration was 1 wt%).

2.6. Visual Observation of Emulsions

The visual observations of all emulsions are shown in Figure 6. The results of the visual observation were consistent with the results of the particle size distribution and microstructure. After four days of storage, significant phase separation occurred in all emulsions except those two emulsions prepared with PGA:DOP = 2:8 (1 wt%) or GA:DOP = 2:8 (1 wt%) as emulsifiers. After six days of storage, the two remaining emulsions also displayed phase separation. According to the above results, the repulsive effect in emulsions could not prevent the droplets from agglomerating during storage. Therefore, we adjusted the concentration and ratio of the compound polysaccharide emulsifier in our further research.

Figure 6.

Figure 6

Open in a new tab

Visual observations (total emulsifier concentration was 1 wt%).

2.7. Apparent Viscosity, Zeta Potential and Particle Size Distribution of the Emulsions

According to Figure 7A, the apparent viscosity and zeta potential of the emulsion changed significantly after adjusting the concentration and ratio of the compounded polysaccharide emulsifier. In emulsions prepared by mixing polysaccharides (GA and DOP), GA primarily contributed to the surface charge, and the amount of the surface charge increased while increasing the concentration of GA. However, when the concentration of GA was gradually increased to 2%, the viscosity of the emulsion reached the maximum value; when the concentration of GA was increased to 5%, the viscosity of the emulsion decreased to a minimum. The viscosity of the polysaccharide system was mainly contributed by DOP, while the viscosity of the emulsion system mainly depended upon the viscosity of the continuous phase [50]. When the GA content in the system gradually increased, DOP no longer dominated, and the viscosity of the emulsion decreased. In addition, many GA molecules in solution might help disperse the DOP molecules more and weaken the interaction between the DOP molecules. Additionally, as the content of GA increased, many GA molecules replaced the adsorbed DOP on the droplet surface due to competitive adsorption, which weakened the interaction between the droplets and reduced the viscosity [35,51]. The particle size distribution of all emulsions was single-peaked, and all emulsions exhibited small average particle sizes, which indicated that the droplet size of the emulsion could be significantly reduced by adjusting the concentration and ratio of the mixed emulsifier. Among them, the average particle size of the emulsion prepared by PGA:DOP = 2:8 (total concentration = 1.5 wt%) was the smallest, followed by the emulsion prepared by 2.0% GA and 1.5% DOP.

Figure 7.

Figure 7

Open in a new tab

(A) The apparent viscosity and zeta potential. (B) The average particle size and particle size distribution. a–d, cd, e, de, f indicate significant differences (p < 0.01).

2.8. Microstructure and Visual Observation

The microstructure and visual observation of the emulsions (Figure 8) were consistent with the particle size of the emulsions. The microstructure of all emulsions displayed small droplets, but the emulsions prepared by 4.0% GA + 1.5% DOP and the emulsions prepared by 5.0% GA + 1.5% DOP displayed many aggregated droplets, which was related to their lower viscosity. Additionally, extremely high concentrations of the emulsifier might flocculate numerous free (not adsorbed on the droplet surface) emulsifier molecules [38,48]. After seven days of storage, the emulsions prepared by PGA:DOP = 2:8 (total concentration = 1.5 wt%) and those prepared by 2.0% GA+1.5%DOP displayed good stability without phase separation.

Figure 8.

Figure 8

Open in a new tab

(A): The microstructure of emulsions (secondary screening of the concentration and ratio of compound polysaccharide emulsifiers); (B) The visual observations of emulsions (secondary screening of the concentration and ratio of compound polysaccharide emulsifiers).

2.9. Rheological Properties of the Emulsions

Figure 9A displays the steady-state flow curve of emulsions. All of the emulsions exhibited the typical non-Newtonian behavior of shear-thinning in the shear rate range of 1 s−1 to 1000 s−1. At the same shear rate, the regularity of the values of the viscosity of different emulsions was the same as the result in Section 3.7. We speculated that there might be an interaction between GA and DOP molecules. As the content of GA continues to increase, GA occupied the binding sites on the DOP molecular chain, resulting in a decrease in the interaction between DOP molecular chains and a decrease in viscosity [35]. The properties of the emulsion system depended mainly upon the characteristics of the continuous phase [50]; so, the rheological behavior of the emulsions was attributed mainly due to the mixed polysaccharides in aqueous solutions. When the shear rate was increased, the entanglements between the polysaccharide-chains were disrupted, and the molecular chains were more randomly orientated. Finally, the interactions between the adjacent chains were reduced, and the viscosity was decreased [52,53,54]. Figure 9B shows the linear viscoelastic region of the two emulsions: the emulsion prepared by PGA:DOP = 2:8 (total concentration = 1.5 wt%) and the emulsion prepared by 2.0% GA + 1.5% DOP. The two emulsions displayed a relatively wide linear viscoelastic region, and G′′ was dominant in the entire test strain range; therefore, a 1% strain was selected for frequency-dependent testing. In Figure 9C, G′ and G′′ of the two emulsions increased while increasing the frequency. In the frequency range of 0.1 Hz–10 Hz, G′′ always dominated (i.e., both emulsions displayed viscous-dominated fluid-like behavior) [55,56,57].

Figure 9.

Figure 9

Open in a new tab

Rheological properties. (A) Steady-state flow curve. (B) Linear viscoelastic zone. (C1) Dynamic frequency sweep of the emulsion prepared by PGA: DOP=2:8 (1.5%); (C2) Dynamic frequency sweep of the emulsion prepared by 2.0% GA + 1.5% DOP.

2.10. Physical Stability of the Emulsions

The physical stability analysis was a space-related and time-related transmission profile over the sample length and the greater change in the transmission with centrifugation, the worse stability of the emulsion [27,58]. In Figure 10A, the transmission curves of all emulsions showed a floating phenomenon (creaming). The transmission curves of the emulsions prepared by 4.0% GA + 1.5% DOP and 5.0% GA + 1.5% DOP were changed significantly, and the transmittance of the two emulsion samples finally exceeded 90%. The transmission curves of the emulsions prepared by PGA:DOP = 2:8 (total concentration = 1.5 wt%) and those prepared by 2.0% GA +1.5% DOP did not change substantially during the test, which indicated that the two emulsions possessed high physical stability. The analytical range of the sample was selected from the meniscus to the bottom to calculate the instability index of the emulsion samples. The speed index of the interface tracking was calculated during the creaming process for a threshold of 16%. In Figure 10B, the emulsions prepared by PGA:DOP = 2:8 (total concentration = 1.5 wt%) and those prepared by 2.0% GA + 1.5% DOP exhibited a lower instability index and smaller speed of interface movement, compared to other emulsion samples. This result was closely related to the viscosity of the emulsion. The high-viscosity continuous phase limited the aggregation of droplets and the movement of molecules. The molecular movement resistance was large, the speed was slow, and macroscopically, the interface movement speed was small.

Figure 10.

Figure 10

Open in a new tab

(A) Light transmittance curve. (B) Instability analysis and interface tracking analysis. The analysis range is from the meniscus to the bottom; a–f indicate significant differences (p < 0.01).

3. Materials and Methods

3.1. Materials and Reagents

Dendrobium officinale stems were procured from Bao Yuan Tang Company (Hainan, China). The D. officinale stem was cultivated in Qiong Zhong County, Hainan Province and harvested after one year.

Gum arabic (GA) was purchased from Aladdin Biochemical Technology Co. Ltd. (Shanghai, China). Propylene glycol alginate (PGA) was procured from Yuanye Bio-Technology Co. Ltd. (Shanghai, China). All other reagents used were of analytical grade.

3.2. Extraction of Dendrobium officinale Polysaccharides

Fifty grams of fresh D. officinale stems were cut into small pieces (sizes of about 2–3 cm) and then soaked in boiling water for 5 min. Subsequently, the stems were removed from boiling water, and water droplets were removed from the surface. Then, the stems were placed in a crusher, and 1000 mL of deionized water was added into it. The stems were crushed for 3 min and then filtered. The filtrate was centrifuged (10,000× g, 30 min), and the supernatant was collected. The supernatant was precipitated with four volumes of 95% ethanol for 24 h. After centrifuging (10,000× g, 20 min), the precipitate was freeze-dried to obtain Dendrobium officinale polysaccharides (HEPDOP).

3.3. Apparent Viscosity Measurement

Apparent viscosity was measured using a Brookfield viscometer (DV3TLVTJ0, Middleboro, MA, USA). A suitable rotor was selected to ensure that the torque was between 10% and 100%. Each sample was measured three times.

3.4. Interfacial Activity of Compound Polysaccharides

According to the method of Li, Yujie et al., the drop shape analysis instrument (DropMeter A-60, MAIST, Ningbo, China) was used for determining the interfacial tension between the polysaccharide solution and coconut oil [41]. Each sample was measured three times.

3.5. Preparation of Oil-in-Water Emulsion

The polysaccharide solution was hydrated at room temperature overnight, then 5% coconut oil was added and homogenized using a high shear homogenizer (FJ-200; Biaoben Instruments, Shanghai, China) at a speed of 10,000 rpm for 2 min [59].

3.6. Droplet Size Distribution of the Emulsions

The average particle diameter and particle size distribution of the emulsions were measured using a laser particle size analyzer (Ineas Physical Optics Instrument Co. Ltd., WJ-60, Shanghai, China). The emulsion was mixed evenly, poured into a stirring tank filled with deionized water, and measured when the shading ratio was 1.5. Each sample was measured three times.

3.7. Zeta Potential Measurement

The zeta-potential of the emulsions was measured using particle electrophoresis (Zetasizer Nano S90, Malvern Instruments, Worcestershire, UK), and each sample was measured three times.

3.8. Microstructure of Emulsions

The microstructure of the emulsions was observed using an inverted fluorescence microscope (AE31AEFL-1NV, Motic, Hong Kong, China). Coconut oil was colored with 0.1% Nile Red [60], and then emulsions were prepared using the colored oil for observing under a 10× eye lens and a 10× objective lens.

3.9. Visual Observation of Emulsions

The prepared emulsion was poured into a 5-mL sample bottle, and the phase separation of the emulsion was captured in a photograph.

3.10. The Rheological Behavior of the Emulsions

The rheological properties of the emulsions were measured using a HAAKE Modular Advanced Rheometer System (MARS 40, Thermo Scientific, Waltham, MA, USA). The 35-mm parallel plate was used with a measurement gap of 1 mm. The sample was evenly loaded between the sample pan and the plate, and the viscosity of the emulsion was measured at a shear rate of 1 to 1000 s−1 to plot a steady-state curve of the emulsion. The linear viscoelastic region of the emulsion was determined in the strain mode, keeping the strain range between 0.5–500%. The dynamic oscillation test of the emulsion was performed at the frequency range of 0.1–10 Hz to calculate the viscoelastic data of the emulsion.

3.11. Physical Stability of the Emulsions

The stability of the emulsions was analyzed by a dispersion analyzer LUMiSizer-651 (Berlin, Germany). The emulsion was loaded into a 2 mm PC centrifuge tube adapted to LUMiSizer-651, scanned at a wavelength of 870 nm and centrifuged at 3500 rpm for 100 min at 25 °C to plot 100 light transmittance curves. The instability index and interface tracking of emulsions were analyzed using SEPView6 software (LUM, Berlin, Germany).

3.12. Statistical Analysis

All data were statistically analyzed using SPSS-Statistics V17 software (IBM, Armonk, NY, USA) through the analysis of variance (ANOVA), followed by Duncan multiple comparisons [61]. The difference between the means was considered significant at p < 0.01.

4. Conclusions

The apparent viscosity and interfacial activity of two compound polysaccharides ((PGA + DOP) and (GA + DOP)) were studied, and oil-in-water emulsions were prepared using the two compound-polysaccharides as emulsifiers. The results showed that the two mixed polysaccharides had better interfacial activity compared to the individual polysaccharides, while the apparent viscosity of the two compound polysaccharides mainly depended upon the content of DOP. Similarly, the emulsions prepared with compound polysaccharides displayed smaller droplet sizes and better stability. Among all emulsions, the emulsions prepared by PGA:DOP = 2:8 (total concentration = 1.5 wt%) and those prepared by 2.0% GA + 1.5% DOP exhibited smaller average droplet sizes, better storage stability, and higher physical centrifugal stability. The results of this study confirmed our hypothesis, providing a system for compound-polysaccharides as emulsifiers. PGA contains numerous esterified carboxyl groups and good hydrophobicity, while DOP is a highly hydrophilic polysaccharide with almost no hydrophobic groups. Therefore, the compound polysaccharide of PGA and DOP is an amphiphilic mixture with good emulsifying properties. Furthermore, GA possesses high hydrophilicity and low viscosity; a stable emulsion requires a higher amount of GA, but the addition of DOP can solve this problem. The DOP could significantly increase the viscosity of the mixed polysaccharides of GA and DOP, and the increase in the viscosity of the continuous phase could significantly improve the stability of the emulsion. In addition, it is exciting that there may be interactions between compounded polysaccharide molecules. For example, the interfacial tension and apparent viscosity of compound polysaccharides are not a single change rule. Previous studies have demonstrated the interaction between different polysaccharide hydrocolloid molecules and the electrostatic interaction between polysaccharides and proteins [1,7,9,62,63,64,65,66]. Therefore, we have evidence to speculate that there is a molecular interaction between DOP and PGA or DOP and GA. This is exactly the research that we are going to do, which is to explore the interaction of DOP with other polysaccharides and their properties in aqueous solution. Ultimately, this study provides a valuable perspective on the application of natural plant polysaccharides as an emulsifier, and offers a new approach for the application of Dendrobium officinale polysaccharides.

Acknowledgments

This research work was financially supported by the Provincial Key Research and Development Project, Hainan Province, China (ZDYF2018071).

Author Contributions

Conceptualization, D.X.; Writing-Original Draft Preparation, B.W.; Data Curation, H.T. All authors have read and agreed to the published version of the manuscript.

Funding

This research was funded by the Provincial Key Research and Development Project, Hainan Province, China ZDYF2018071.

Conflicts of Interest

The authors declare no conflict of interest.

Footnotes

Sample Availability: Not available.

References

  • 1.Albano K.M., Cavallieri Â.L.F., Nicoletti V.R. Electrostatic interaction between proteins and polysaccharides: Physicochemical aspects and applications in emulsion stabilization. Food Rev. Int. 2018;35:54–89. doi: 10.1080/87559129.2018.1467442. [DOI] [Google Scholar]
  • 2.Castel V., Rubiolo A.C., Carrara C.R. Droplet size distribution, rheological behavior and stability of corn oil emulsions stabilized by a novel hydrocolloid (Brea gum) compared with gum arabic. Food Hydrocoll. 2017;63:170–177. doi: 10.1016/j.foodhyd.2016.08.039. [DOI] [Google Scholar]
  • 3.Vianna-Filho R.P., Petkowicz C.L., Silveira J.L. Rheological characterization of O/W emulsions incorporated with neutral and charged polysaccharides. Carbohydr. Polym. 2013;93:266–272. doi: 10.1016/j.carbpol.2012.05.014. [DOI] [PubMed] [Google Scholar]
  • 4.Lei J., Gao Y., Ma Y., Zhao K., Du F. Improving the emulsion stability by regulation of dilational rheology properties. Colloids Surf. A Physicochem. Eng. Asp. 2019;583:123906. doi: 10.1016/j.colsurfa.2019.123906. [DOI] [Google Scholar]
  • 5.Hosseini A., Jafari S.M., Mirzaei H., Asghari A., Akhavan S. Application of image processing to assess emulsion stability and emulsification properties of Arabic gum. Carbohydr. Polym. 2015;126:1–8. doi: 10.1016/j.carbpol.2015.03.020. [DOI] [PubMed] [Google Scholar]
  • 6.Bai L., Huan S., Li Z., McClements D.J. Comparison of emulsifying properties of food-grade polysaccharides in oil-in-water emulsions: Gum arabic, beet pectin, and corn fiber gum. Food Hydrocoll. 2017;66:144–153. doi: 10.1016/j.foodhyd.2016.12.019. [DOI] [Google Scholar]
  • 7.Liang Y., Gillies G., Patel H., Matia-Merino L., Ye A., Golding M. Physical stability, microstructure and rheology of sodium-caseinate-stabilized emulsions as influenced by protein concentration and non-adsorbing polysaccharides. Food Hydrocoll. 2014;36:245–255. doi: 10.1016/j.foodhyd.2013.10.006. [DOI] [Google Scholar]
  • 8.Verkempinck S.H.E., Kyomugasho C., Salvia-Trujillo L., Denis S., Bourgeois M., Van Loey A.M., Hendrickx M.E., Grauwet T. Emulsion stabilizing properties of citrus pectin and its interactions with conventional emulsifiers in oil-in-water emulsions. Food Hydrocoll. 2018;85:144–157. doi: 10.1016/j.foodhyd.2018.07.014. [DOI] [Google Scholar]
  • 9.Xu X.F., Liu W., Luo L., Liu C., McClements B.D.J. Influence of anionic polysaccharides on the physical and oxidative stability of hydrolyzed rice glutelin emulsions: Impact of polysaccharide type and pH. Food Hydrocoll. 2017;72:185–194. doi: 10.1016/j.foodhyd.2017.05.018. [DOI] [Google Scholar]
  • 10.Melanie H., Taarji N., Zhao Y., Khalid N., Neves M.A., Kobayashi I., Tuwo A., Nakajima M. Formulation and characterisation of O/W emulsions stabilised with modified seaweed polysaccharides. Int. J. Food Sci. Technol. 2020;55:211–221. doi: 10.1111/ijfs.14264. [DOI] [Google Scholar]
  • 11.Bhattarai M., Pitkänen L., Kitunen V., Korpinen R., Ilvesniemi H., Kilpeläinen P.O., Lehtonen M., Mikkonen K.S. Functionality of spruce galactoglucomannans in oil-in-water emulsions. Food Hydrocoll. 2019;86:154–161. doi: 10.1016/j.foodhyd.2018.03.020. [DOI] [Google Scholar]
  • 12.Georgiadis N., Ritzoulis C., Charchari E., Koukiotis C., Tsioptsias C., Vasiliadou C. Isolation, characterization and emulsion stabilizing properties of polysaccharides form orchid roots (salep) Food Hydrocoll. 2012;28:68–74. doi: 10.1016/j.foodhyd.2011.12.001. [DOI] [Google Scholar]
  • 13.Osano J.P., Hosseini-Parvar S.H., Matia-Merino L., Golding M. Emulsifying properties of a novel polysaccharide extracted from basil seed (Ocimum bacilicum L.): Effect of polysaccharide and protein content. Food Hydrocoll. 2014;37:40–48. doi: 10.1016/j.foodhyd.2013.09.008. [DOI] [Google Scholar]
  • 14.Fan H., Meng Q., Xiao T., Zhang L. Partial characterization and antioxidant activities of polysaccharides sequentially extracted from Dendrobium officinale. J. Food Meas. Charact. 2018;12:1054–1064. doi: 10.1007/s11694-018-9721-8. [DOI] [Google Scholar]
  • 15.Chan C.F., Wu C.T., Huang W.Y., Lin W.S., Wu H.W., Huang T.K., Chang M.Y., Lin Y.S. Antioxidation and Melanogenesis Inhibition of Various Dendrobium tosaense Extracts. Molecules. 2018;23:1810. doi: 10.3390/molecules23071810. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 16.Liu H., Ma J., Gong F., Wei F., Zhang X., Wu H. Structural characterisation and immunomodulatory effects of polysaccharides isolated from Dendrobium aphyllum. Int. J. Food Sci. Technol. 2018;53:1185–1194. doi: 10.1111/ijfs.13695. [DOI] [Google Scholar]
  • 17.Chen N.-D., Chen N.-F., Li J., Cao C.-Y., Wang J.-M., Huang H.-P. Similarity Evaluation of Different Origins and Species of Dendrobiums by GC-MS and FTIR Analysis of Polysaccharides. Int. J. Anal. Chem. 2015;2015:713410. doi: 10.1155/2015/713410. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 18.Huang K., Li Y., Tao S., Wei G., Huang Y., Chen D., Wu C. Purification, Characterization and Biological Activity of Polysaccharides from Dendrobium officinale. Molecules. 2016;21:701. doi: 10.3390/molecules21060701. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 19.Luo Q.-L., Tang Z.-H., Zhang X.-F., Zhong Y.-H., Yao S.-Z., Wang L.-S., Lin C.-W., Luo X. Chemical properties and antioxidant activity of a water-soluble polysaccharide from Dendrobium officinale. Int. J. Biol. Macromol. 2016;89:219–227. doi: 10.1016/j.ijbiomac.2016.04.067. [DOI] [PubMed] [Google Scholar]
  • 20.Li F., Cui S.-H., Zha X.-Q., Bansal V., Jiang Y.-L., Asghar M.-N., Wang J.-H., Pan L.-H., Xu B.-F., Luo J.-P. Structure and bioactivity of a polysaccharide extracted from protocorm-like bodies of Dendrobium huoshanense. Int. J. Biol. Macromol. 2015;72:664–672. doi: 10.1016/j.ijbiomac.2014.08.026. [DOI] [PubMed] [Google Scholar]
  • 21.Wei W., Feng L., Bao W.-R., Ma D.-L., Leung C.-H., Nie S.-P., Han Q.-B. Structure Characterization and Immunomodulating Effects of Polysaccharides Isolated from Dendrobium officinale. J. Agric. Food Chem. 2016;64:881–889. doi: 10.1021/acs.jafc.5b05180. [DOI] [PubMed] [Google Scholar]
  • 22.He T.B., Huang Y.P., Yang L., Liu T.T., Gong W.Y., Wang X.J., Sheng J., Hu J.M. Structural characterization and immunomodulating activity of polysaccharide from Dendrobium officinale. Int. J. Biol Macromol. 2016;83:34–41. doi: 10.1016/j.ijbiomac.2015.11.038. [DOI] [PubMed] [Google Scholar]
  • 23.Yue H., Liu Y., Qu H., Ding K. Structure analysis of a novel heteroxylan from the stem of Dendrobium officinale and anti-angiogenesis activities of its sulfated derivative. Int. J. Biol. Macromol. 2017;103:533–542. doi: 10.1016/j.ijbiomac.2017.05.097. [DOI] [PubMed] [Google Scholar]
  • 24.Dai L., Sun C., Wei Y., Zhan X., Mao L., Gao Y. Formation and characterization of zein-propylene glycol alginate-surfactant ternary complexes: Effect of surfactant type. Food Chem. 2018;258:321–330. doi: 10.1016/j.foodchem.2018.03.077. [DOI] [PubMed] [Google Scholar]
  • 25.Cheong K.W., Mirhosseini H., Hamid N.S., Osman A., Basri M., Tan C.P. Effects of propylene glycol alginate and sucrose esters on the physicochemical properties of modified starch-stabilized beverage emulsions. Molecules. 2014;19:8691–8706. doi: 10.3390/molecules19068691. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 26.Sun C., Dai L., Gao Y. Interaction and formation mechanism of binary complex between zein and propylene glycol alginate. Carbohydr. Polym. 2017;157:1638–1649. doi: 10.1016/j.carbpol.2016.11.046. [DOI] [PubMed] [Google Scholar]
  • 27.Sun C., Dai L., Gao Y. Binary Complex Based on Zein and Propylene Glycol Alginate for Delivery of Quercetagetin. Biomacromolecules. 2016;17:3973–3985. doi: 10.1021/acs.biomac.6b01362. [DOI] [PubMed] [Google Scholar]
  • 28.Guo Q., Su J., Yuan F., Mao L., Gao Y. Preparation, characterization and stability of pea protein isolate and propylene glycol alginate soluble complexes. LWT. 2019;101:476–482. doi: 10.1016/j.lwt.2018.11.057. [DOI] [Google Scholar]
  • 29.Dai L., Yang S., Wei Y., Sun C., McClements D.J., Mao L., Gao Y. Development of stable high internal phase emulsions by pickering stabilization: Utilization of zein-propylene glycol alginate-rhamnolipid complex particles as colloidal emulsifiers. Food Chem. 2019;275:246–254. doi: 10.1016/j.foodchem.2018.09.122. [DOI] [PubMed] [Google Scholar]
  • 30.Wu Y., Gong Z., Shen Y., Qi Y., Ling F. The efficacy of propylene glycol alginate (PGA), a food additive, in controlling Haemaphysalis longicornis ticks. Ticks Tick Borne Dis. 2018;9:1532–1536. doi: 10.1016/j.ttbdis.2018.07.014. [DOI] [PubMed] [Google Scholar]
  • 31.de Souza A.G., Cesco C.T., de Lima G.F., Artifon S.E.S., Rosa D.d.S., Paulino A.T. Arabic gum-based composite hydrogels reinforced with eucalyptus and pinus residues for controlled phosphorus release. Int. J. Biol. Macromol. 2019;140:33–42. doi: 10.1016/j.ijbiomac.2019.08.106. [DOI] [PubMed] [Google Scholar]
  • 32.Patel S., Goyal A. Applications of Natural Polymer Gum Arabic: A Review. Int. J. Food Prop. 2015;18:986–998. doi: 10.1080/10942912.2013.809541. [DOI] [Google Scholar]
  • 33.Atgié M., Garrigues J.C., Chennevière A., Masbernat O., Roger K. Gum Arabic in solution: Composition and multi-scale structures. Food Hydrocoll. 2019;91:319–330. doi: 10.1016/j.foodhyd.2019.01.033. [DOI] [Google Scholar]
  • 34.Shaddel R., Hesari J., Azadmard-Damirchi S., Hamishehkar H., Fathi-Achachlouei B., Huang Q. Use of gelatin and gum Arabic for encapsulation of black raspberry anthocyanins by complex coacervation. Int. J. Biol. Macromol. 2018;107:1800–1810. doi: 10.1016/j.ijbiomac.2017.10.044. [DOI] [PubMed] [Google Scholar]
  • 35.Nishinari K., Fang Y., Yang N., Yao X., Zhao M., Zhang K., Gao Z. Gels emulsions and application of hydrocolloids at Phillips Hydrocolloids Research Centre. Food Hydrocoll. 2018;78:36–46. doi: 10.1016/j.foodhyd.2017.07.035. [DOI] [Google Scholar]
  • 36.Han L., Hu B., Ma R., Gao Z., Nishinari K., Phillips G.O., Yang J., Fang Y. Effect of arabinogalactan protein complex content on emulsification performance of gum arabic. Carbohyd. Polym. 2019;224:115170. doi: 10.1016/j.carbpol.2019.115170. [DOI] [PubMed] [Google Scholar]
  • 37.Hu B., Han L., Kong H., Nishinari K., Phillips G.O., Yang J., Fang Y. Preparation and emulsifying properties of trace elements fortified gum arabic. Food Hydrocoll. 2019;88:43–49. doi: 10.1016/j.foodhyd.2018.09.027. [DOI] [Google Scholar]
  • 38.McClements D.J., Bai L., Chung C. Recent Advances in the Utilization of Natural Emulsifiers to Form and Stabilize Emulsions. Annu Rev. Food Sci. Technol. 2017;8:205–236. doi: 10.1146/annurev-food-030216-030154. [DOI] [PubMed] [Google Scholar]
  • 39.Niu F., Niu D., Zhang H., Chang C., Gu L., Su Y., Yang Y. Ovalbumin/gum arabic-stabilized emulsion: Rheology, emulsion characteristics, and Raman spectroscopic study. Food Hydrocoll. 2016;52:607–614. doi: 10.1016/j.foodhyd.2015.08.010. [DOI] [Google Scholar]
  • 40.Zhang N., Chen H., Ma L., Zhang Y. Physical modifications of polysaccharide from Inonotus obliquus and the antioxidant properties. Int. J. Biol. Macromol. 2013;54:209–215. doi: 10.1016/j.ijbiomac.2012.12.030. [DOI] [PubMed] [Google Scholar]
  • 41.Li Y., Xiang D. Stability of oil-in-water emulsions performed by ultrasound power or high-pressure homogenization. PLoS ONE. 2019;14:e0213189. doi: 10.1371/journal.pone.0213189. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 42.Golkar A., Taghavi S.M., Aghili Dehnavi F. The emulsifying properties of Persian gum (Amygdalus scoparia Spach) as compared with gum Arabic. Int. J. Food Prop. 2018;21:416–436. doi: 10.1080/10942912.2018.1454464. [DOI] [Google Scholar]
  • 43.Mozafarpour R., Koocheki A., Milani E., Varidi M. Extruded soy protein as a novel emulsifier: Structure, interfacial activity and emulsifying property. Food Hydrocoll. 2019;93:361–373. doi: 10.1016/j.foodhyd.2019.02.036. [DOI] [Google Scholar]
  • 44.Zhang R., Cai Y., Wang J., Zhao Z., Mao X., Peng Z. A Star-Shaped Anionic Surfactant: Synthesis, Alkalinity Resistance, Interfacial Tension and Emulsification Properties at the Crude Oil–Water Interface. J. Surfactants Deterg. 2017;20:1027–1035. doi: 10.1007/s11743-017-1988-y. [DOI] [Google Scholar]
  • 45.Kumari R., Kakati A., Nagarajan R., Sangwai J.S. Synergistic effect of mixed anionic and cationic surfactant systems on the interfacial tension of crude oil-water and enhanced oil recovery. J. Dispers. Sci. Technol. 2018;40:969–981. doi: 10.1080/01932691.2018.1489280. [DOI] [Google Scholar]
  • 46.Wei Y., Sun C., Dai L., Mao L., Yuan F., Gao Y. Novel Bilayer Emulsions Costabilized by Zein Colloidal Particles and Propylene Glycol Alginate, Part 1: Fabrication and Characterization. J. Agric. Food Chem. 2019;67:1197–1208. doi: 10.1021/acs.jafc.8b03240. [DOI] [PubMed] [Google Scholar]
  • 47.Zhang Q., Yang L., Hu S., Liu X., Duan X. Consequences of ball-milling treatment on the physicochemical, rheological and emulsifying properties of egg phosvitin. Food Hydrocoll. 2019;95:418–425. doi: 10.1016/j.foodhyd.2019.04.064. [DOI] [Google Scholar]
  • 48.McClements D.J., Gumus C.E. Natural emulsifiers—Biosurfactants, phospholipids, biopolymers, and colloidal particles: Molecular and physicochemical basis of functional performance. Adv. Colloid Interface Sci. 2016;234:3–26. doi: 10.1016/j.cis.2016.03.002. [DOI] [PubMed] [Google Scholar]
  • 49.Chivero P., Gohtani S., Yoshii H., Nakamura A. Effect of xanthan and guar gums on the formation and stability of soy soluble polysaccharide oil-in-water emulsions. Food Res. Int. 2015;70:7–14. doi: 10.1016/j.foodres.2015.01.025. [DOI] [Google Scholar]
  • 50.Quinzio C., Ayunta C., López de Mishima B., Iturriaga L. Stability and rheology properties of oil-in-water emulsions prepared with mucilage extracted from Opuntia ficus-indica (L). Miller. Food Hydrocoll. 2018;84:154–165. doi: 10.1016/j.foodhyd.2018.06.002. [DOI] [Google Scholar]
  • 51.Yang N., Mao P., Lv R., Zhang K., Fang Y., Nishinari K., Phillips G.O. Stability and Oil Migration of Oil-in-Water Emulsions Emulsified by Phase-Separating Biopolymer Mixtures. J. Food Sci. 2016;81:1971–1980. doi: 10.1111/1750-3841.13384. [DOI] [PubMed] [Google Scholar]
  • 52.Xu J.L., Zhang J.C., Liu Y., Sun H.J., Wang J.H. Rheological properties of a polysaccharide from floral mushrooms cultivated in Huangshan Mountain. Carbohydr. Polym. 2016;139:43–49. doi: 10.1016/j.carbpol.2015.12.011. [DOI] [PubMed] [Google Scholar]
  • 53.Qiao L., Li Y., Chi Y., Ji Y., Gao Y., Hwang H., Aker W.G., Wang P. Rheological properties, gelling behavior and texture characteristics of polysaccharide from Enteromorpha prolifera. Carbohydr. Polym. 2016;136:1307–1314. doi: 10.1016/j.carbpol.2015.10.030. [DOI] [PubMed] [Google Scholar]
  • 54.Yaich H., Garna H., Besbes S., Barthélemy J.-P., Paquot M., Blecker C., Attia H. Impact of extraction procedures on the chemical, rheological and textural properties of ulvan from Ulva lactuca of Tunisia coast. Food Hydrocoll. 2014;40:53–63. doi: 10.1016/j.foodhyd.2014.02.002. [DOI] [Google Scholar]
  • 55.Anvari M., Joyner H.S. Effect of fish gelatin and gum arabic interactions on concentrated emulsion large amplitude oscillatory shear behavior and tribological properties. Food Hydrocoll. 2018;79:518–525. doi: 10.1016/j.foodhyd.2017.12.016. [DOI] [Google Scholar]
  • 56.Huang Q., Jin W., Ye S., Hu Y., Wang Y., Xu W., Li J., Li B. Comparative studies of konjac flours extracted from Amorphophallus guripingensis and Amorphophallus rivirei: Based on chemical analysis and rheology. Food Hydrocoll. 2016;57:209–216. doi: 10.1016/j.foodhyd.2016.01.017. [DOI] [Google Scholar]
  • 57.Jin W., Xu W., Li Z., Li J., Zhou B., Zhang C., Li B. Degraded konjac glucomannan by γ-ray irradiation assisted with ethanol: Preparation and characterization. Food Hydrocoll. 2014;36:85–92. doi: 10.1016/j.foodhyd.2013.09.005. [DOI] [Google Scholar]
  • 58.Jin Q., Li X., Cai Z., Zhang F., Yadav M.P., Zhang H. A comparison of corn fiber gum, hydrophobically modified starch, gum arabic and soybean soluble polysaccharide: Interfacial dynamics, viscoelastic response at oil/water interfaces and emulsion stabilization mechanisms. Food Hydrocoll. 2017;70:329–344. doi: 10.1016/j.foodhyd.2017.03.005. [DOI] [Google Scholar]
  • 59.Li Y., Xiang D., Wang B., Gong X. Oil-in-Water Emulsions Stabilized by Ultrasonic Degraded Polysaccharide Complex. Molecules. 2019;24:1097. doi: 10.3390/molecules24061097. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 60.Yang J.-Y., Peng B., Wang M., Zou X.-G., Yin Y.-L., Deng Z.-Y. Characteristics and emulsifying properties of two protein fractions derived from the emulsion formed during aqueous extraction of Camellia oil. Food Hydrocoll. 2019;87:644–652. doi: 10.1016/j.foodhyd.2018.08.043. [DOI] [Google Scholar]
  • 61.Tabilo-Munizaga G., Barbosa-Cánovas G.V. Rheology for the food industry. J. Food Eng. 2005;67:147–156. doi: 10.1016/j.jfoodeng.2004.05.062. [DOI] [Google Scholar]
  • 62.Gulcin Yildiz J.D., Andrade J., Engeseth N.J., Hao F. Effect of plant protein-polysaccharide complexes produced by mano-thermosonication and pH-shifting on the structure and stability of oil-in-water emulsions. Innov. Food Sci. Emerg. Technol. 2018;47:317–325. doi: 10.1016/j.ifset.2018.03.005. [DOI] [Google Scholar]
  • 63.Pilosof A.M.R. Potential impact of interfacial composition of proteins and polysaccharides stabilized emulsions on the modulation of lipolysis. The role of bile salts. Food Hydrocoll. 2017;68:178–185. doi: 10.1016/j.foodhyd.2016.08.030. [DOI] [Google Scholar]
  • 64.Hager A.-S., Arendt E.K. Influence of hydroxypropylmethylcellulose (HPMC), xanthan gum and their combination on loaf specific volume, crumb hardness and crumb grain characteristics of gluten-free breads based on rice, maize, teff and buckwheat. Food Hydrocoll. 2013;32:195–203. doi: 10.1016/j.foodhyd.2012.12.021. [DOI] [Google Scholar]
  • 65.Rutz J.K., Zambiazi R.C., Borges C.D., Krumreich F.D., da Luz S.R., Hartwig N., da Rosa C.G. Microencapsulation of purple Brazilian cherry juice in xanthan, tara gums and xanthan-tara hydrogel matrixes. Carbohydr. Polym. 2013;98:1256–1265. doi: 10.1016/j.carbpol.2013.07.058. [DOI] [PubMed] [Google Scholar]
  • 66.Yuan C., Xu D., Cui B., Wang Y. Gelation of κ-carrageenan/Konjac glucommanan compound gel: Effect of cyclodextrins. Food Hydrocoll. 2018;87:158–164. doi: 10.1016/j.foodhyd.2018.07.037. [DOI] [Google Scholar]

Articles from Molecules are provided here courtesy of Multidisciplinary Digital Publishing Institute (MDPI)

RESOURCES