Skip to main content
Nano-Micro Letters logoLink to Nano-Micro Letters
. 2020 Jan 28;12:42. doi: 10.1007/s40820-020-0373-y

Natural and Eco-Friendly Materials for Triboelectric Energy Harvesting

Vladislav Slabov 1,2, Svitlana Kopyl 1, Marco P Soares dos Santos 2,3, Andrei L Kholkin 1,4,5,
PMCID: PMC7770886  PMID: 34138259

Highlights

  • An up-to-date review of the natural materials used for triboelectric energy harvesting is provided.

  • Major parameters of the electric output are identified and compared for different materials.

  • Best results (14 mW) were obtained for dry leaf powder in combination with poly(vinylidene fluoride) in contact-separation mode.

Keywords: Natural and eco-friendly materials, Energy harvesting, Triboelectric nanogenerators, Biocompatibility

Abstract

Triboelectric nanogenerators (TENGs) are promising electric energy harvesting devices as they can produce renewable clean energy using mechanical excitations from the environment. Several designs of triboelectric energy harvesters relying on biocompatible and eco-friendly natural materials have been introduced in recent years. Their ability to provide customizable self-powering for a wide range of applications, including biomedical devices, pressure and chemical sensors, and battery charging appliances, has been demonstrated. This review summarizes major advances already achieved in the field of triboelectric energy harvesting using biocompatible and eco-friendly natural materials. A rigorous, comparative, and critical analysis of preparation and testing methods is also presented. Electric power up to 14 mW was already achieved for the dry leaf/polyvinylidene fluoride-based TENG devices. These findings highlight the potential of eco-friendly self-powering systems and demonstrate the unique properties of the plants to generate electric energy for multiple applications.graphic file with name 40820_2020_373_Figa_HTML.jpg

Introduction

Energy harvesting is a global area of research that includes the development of suitable methods of environmental energy collection, selection of materials, and customization of harvester designs, so that harvesters can operate over long periods of time with reduced intermittency and impact on environment, while ensuring low production and ecological costs. Many transduction mechanisms for energy harvesting have already been developed, and many designs of harvesting devices have been provided for a wide range of applications from small- to large-scale powering [17]. A few years ago, the interest of researchers was attracted by the triboelectric effect, by which electricity is produced due to mechanical friction between two bodies in a motion [8, 9]. This triboelectric effect has been known for a long time and is thought to be purely electrostatic in binary systems [10, 11]. Charge generation from friction has also been investigated in some polymers due to the chemical reaction of radicals [12, 13]. Though triboelectricity has been observed a long time ago, it was considered as a harmful phenomenon and many efforts were spent to avoid it (e.g., to facilitate the transport of powders and recycled materials) [1417]. Only recently triboelectricity was applied for self-powering of a broad range of highly sophisticated devices, although the charge generation mechanism is still under discussion [18, 19]. However, despite the absence of the viable theory of triboelectricity, such findings opened up new possibilities for electric energy harvesting [2022].

As the charge generation phenomena occur mainly on the nanoscale, energy harvesting devices based on triboelectric effect are called triboelectric nanogenerators (TENGs). Four work modes have already been identified to characterize and apply TENGs for electric energy harvesting: vertical contact-separation mode, lateral sliding mode, single-electrode mode, and freestanding triboelectric layer mode (Fig. 1a) [23]. During the motion process (sliding or separation), opposite charges on the surface of materials are produced, whose amount will significantly increase if the surface area increases and changes according to the different composition and structure of materials [24, 25]. Several studies have been conducted to understand the charge formation mechanisms, and they also provided the basis for measurements standards [2628]. In another work, Zou et al. [29] demonstrated how to measure triboelectricity by using several polymers as examples. Since the most used materials for TENGs are currently polymers, their surfaces were modified to increase the output electric current and voltage (Fig. 1b) [3033]. Moreover, the effect of surface functionalization on the main features of TENG harvesters has been rigorously studied. As a result, many materials with the ability to harvest energy by friction have been identified [34, 35]. In addition, several efficient designs for applications using powering by TENG harvesters have been proposed (Fig. 1b–d) [3639]. A common architecture of TENGs designed according to the contact-separation mode uses springs or polymer spacers between the bodies [4, 37].

Fig. 1.

Fig. 1

The main modes of triboelectric nanogenerators (TENGs) and examples of construction: a four main working modes, and b example of the surface modification of the polymer-based TENG. Reprinted with permission from Ref. [30]. Copyright (2012) American Chemical Society. c Example of construction of a TENG operating under the contact-separation mode using springs. Adapted with permission from Ref. [36]. Copyright (2013) American Chemical Society. d Schematic illustration of the polymer TENG operating under the contact-separation mode using a spacer. Reprinted with permission from Ref. [39]. Copyright (2012) American Chemical Society

Recently, several natural materials were found with ability to harvest electric energy from dynamics of mechanical power sources ensuring low-cost production, as well as ecological safety and biocompatibility during uninterrupted or intermittent contacts with the human body. Humans may provide a large amount of mechanical energy during their daily living (the electric power may exceed 70 W), which can be converted to produce significant amounts of useful energy by triboelectric generation [40, 41]. Many applications (e.g., innovative biomedical sensors that monitor daily activity and functioning of the organism and multifunctional medical devices) require biocompatible materials in contact with human skin or implanted inside the body [4244]. Typically, the materials for biocompatible applications are those produced by nature or using natural products [4547]. This paper presents an up-to-date review of the relevant literature reports that highlight major scientific achievements in this area and guides readers through innovative approaches for power generation, harvester designs and parameters that influence the output performance. Our main goal is to provide the relevant findings related to simple materials produced by nature that can substitute fully polymeric TENGs such that they can be used to produce a significant amount of electric energy via the triboelectric effect.

Natural Materials

Natural materials are a special class of materials that can be suitably used for triboelectric applications. By definition, this class is fully biocompatible and eco-friendly without any recycling problems. These materials opened up a new possibility for harvesting electric energy because their manufacture is neither complex nor expensive, and their output performance is similar to traditional polymer/ceramic materials. TENGs based on natural materials have been recently investigated in detail, and the conclusions showed that their complex surface architecture causes major impacts on the produced charge, current, or voltage [4851]. Since natural materials have hierarchically structured surfaces, surface modification is not required in many cases, and they can be used for polymer modification by soft lithography as well [5254]. Besides, the combination of natural materials with biocompatible polymers allows the production of eco-friendly triboelectric pairs for energy harvesting. We highlight here three kinds of biomaterials applied in energy harvesting: (1) plants and their parts (mainly leaves); (2) the plant products, namely sugar and cellulose [55, 56]; (3) biodegradable materials (spider silk, egg white, chitin, etc.). Their harvesting performance and possible applications will be overviewed as well.

Plants

As it is well known, the triboelectric effect is based on converting kinetic energy into electric energy during the contact of two different materials in an area-dependent manner [49]. For this reason, materials in contact must have large enough contact areas so that the harvested energy can be maximized [48, 57, 58]. Plant materials provide a wide range of natural surfaces, which allow their application as friction bodies. The surfaces of the plants are, therefore, used as masks for soft lithography—for example, polymers can replicate all surface jaggies of the leaves [59]. Moreover, they can be also used as triboelectric pairs. It is worth to note that triboelectrification occurs naturally in many plants (e.g., in petals) [60], which were already applied to increase friction. The petal surface is characterized by a sophisticated microstructure, which naturally enlarges the contact area between the surfaces (Fig. 2a). Using these properties, a TENG using petals (Chinese rose) was able to supply commercial LEDs by vibration stress [60]. Not only flower petals can be used as natural harvesters based on the triboelectric effect, but also other parts of the plants as well. Noticeably, an extended electric bilayer sub-structure was found in the Rhododendron plant and its leaf was also used for triboelectric energy harvesting [61]. Figure 2b presents the schematics of the layers in a Rhododendron leaf. Recent findings clearly show that separate parts of leaf body can work as electrical structures, although they must be in contact with other dielectric materials (e.g., polymers) for electric power maximization. (Contact of similar nature materials commonly provides lower output performances.) The use of a plant leaf as a triboelectric pair material was also studied for the case of a Hosta leaf [62]. As the natural leaf of any plant is full of water and comprises an electrolyte, it can be also used as a conductive liquid. Figure 2c demonstrates how the electrolyte allows the use of a leaf in a single-electrode mode for triboelectric energy harvesting. Table 1 summarizes the properties of seven different leaves with different natural surfaces. These TENGs clearly demonstrate the impact of the natural materials’ morphology on the output performance. Because the fresh leaf will dry during triboelectric cycling, both options (fresh and dry leaves) have been explored by Feng et al. [63]. These authors [63] designed a hybrid wind–TENG (WTENG) based on the fresh leaf and powder from the dry leaf (Fig. 2d). In this experiment, the dry leaf was milled into a powder and then covered by polylysine (PLL) using a spin-coating method. To compare this modified WTENG with the one based on a leaf, contact-separation mode driven by an electric motor was used. Enhanced electric energy was harvested for the leaf powder: Up to 60 μA and 1000 V under 5 Hz speed frequency were observed. Besides, up to 70 μA and 150 V were achieved using a potted-plant-based wind-driven harvesting system (Fig. 2e) at 7 m s−1 wind speed. Combination of WTENG with the tree was intended for several novel applications [62]. Using this design, the leaf TENG can work in a freestanding mode, which allows a transduction of mechanical energy without grounding. The mechanical force can be delivered to the plants either by wind or rain. This fact motivated further research using a similar TENG design based on a lotus leaf for water–solid contact scenarios [64] (Fig. 2f).

Fig. 2.

Fig. 2

The design of TENGs using plants: a surface of the petal rose and schematics of the contact-separation mode TENG with petal. Reprinted with permission from Ref. [60]. Copyright (2018) Published by Elsevier Ltd. b Schematics of the rhododendron leaf as an electric bilayer structure. Reprinted with permission from Ref. [61]. Copyright (2018) Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim. c Schematic illustration of the working principles of leaf TENG in the single-electrode mode. i) contact state, ii) separating state, iii) separated state, iv) approaching state. Reprinted with permission from Ref. [62]. Copyright (2018) Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim. d Structure of the fresh leaf and dry powder. e Schematics and proof of the concept of plant modification for designing TENGs. Reprinted with permission from Ref. [63]. Copyright (2018) Published by Elsevier Ltd; f Schematics of the water–solid contact. Reprinted with permission from Ref. [64]. Copyright (2017) Published by Elsevier Ltd

Table 1.

Triboelectric pair materials and their triboelectric characteristics

Triboelectric pair: material 1 Triboelectric pair: material 2 Used mode and fabrication methods Contract area (cm2) Electric characterizationa Mechanical excitation
Petal rose [60] Poly(methyl methacrylate) (PMMA)

Single-electrode mode

Handmade

3 × 3

Voc = 30.6 V

Isc = 0.78 µA

P = 24 µW

Pdensity ≈ 2.7 µW cm−2

100 N

2 Hz

Hosta leaf [62] Poly(methyl methacrylate) (PMMA)

Single-electrode mode

Handmade

8 × 8

Voc = 230 V

Isc = 9.5 µA

P = 2185 µW

Pdensity ≈ 34.1 µW cm−2

2 Hz

0.333 m/s

M. denudate [62] Poly(methyl methacrylate) (PMMA)

Single-electrode mode

Handmade

8 × 8

Voc ≈ 100 V

Isc ≈ 3.5 µA

P = 350 µW

Pdensity ≈ 5.5 µW cm−2

2 Hz

0.333 m/s

L. chinense [62] Poly(methyl methacrylate) (PMMA)

Single-electrode mode

Handmade

8 × 8

Voc ≈ 110 V

Isc ≈ 4 µA

P = 440 µW

Pdensity ≈ 6.9 µW cm−2

2 Hz

0.333 m/s

Firmiana [62] Poly(methyl methacrylate) (PMMA)

Single-electrode mode

Handmade

8 × 8

Voc ≈ 90 V

Isc ≈ 2.8 µA

P = 252 µW

Pdensity ≈ 3.9 µW cm−2

2 Hz

0.333 m/s

Populus [62] Poly(methyl methacrylate) (PMMA)

Single-electrode mode

Handmade

8 × 8

Voc ≈ 115 V

Isc ≈ 3.5 µA

P = 402.5 µW

Pdensity ≈ 6.3 µW cm−2

2 Hz

0.333 m/s

Lotus [62] Poly(methyl methacrylate) (PMMA)

Single-electrode mode

Handmade

8 × 8

Voc ≈ 100 V

Isc ≈ 2.8 µA

P = 280 µW

Pdensity ≈ 4.4 µW cm−2

2 Hz

0.333 m/s

E. aureum [62] Poly(methyl methacrylate) (PMMA)

Single-electrode mode

Handmade

8 × 8

Voc ≈ 90 V

Isc ≈ 2 µA

P = 180 µW

Pdensity ≈ 2.8 µW cm−2

2 Hz

0.333 m/s

Rhododendron leaves [61] Ecoflex (silicone elastomer film)

Single-electrode mode

Handmade

4.5 × 4.5

V ≈ 140 V

Pdensity = 15 µW cm−2

10 Hz

0.9 N

Fresh leaf [63]

Poly(vinylidene

fluoride) (PVDF)

Contact-separation mode

Spin-coating + handmade

4 × 4

Voc ≈ 430 V

Isc ≈ 15 µA

P = 6450 µW

Pdensity ≈ 403.1 µW cm−2

5 Hz
Dry leaf (powder) [63]

Poly(vinylidene

fluoride) (PVDF)

Contact-separation mode

Spin-coating + handmade

4 × 4

Voc ≈ 560 V

Isc ≈ 25 µA

P = 14,000 µW

Pdensity ≈ 875 µW/cm2

5 Hz

Polydimethyl siloxane + cellulose nanocrystal flakes (PDMS/CNCFs)

[70]

Aluminum

Single-electrode mode

Spin-coating + handmade

1.5 × 1.5

Voc ≈ 320 V

Isc ≈ 5 µA cm−2

P = 1600 µW cm2

40 N
Cellulose paper [71] Poly(caprolactone)/graphene oxide 4% (PCL/GO 4%)

Contact-separation mode

Electrospinning + handmade

2 × 4

Voc ≈ 120 V

Isc ≈ 4 µA

P = 480 µW

Pdensity ≈ 60 µW cm−2

15 N

3 Hz

Cellulose nanofibril paper + 4% Phosphorene [72] Polyethylene terephthalate (PET)

Contact-separation mode

Electrode sputtering + handmade

Voc = 5.2 V

After 6 months

Voc = 4 V

70 N
Cellulose nanofibrils (CNF) [82] Fluorinated ethylene propylene (FEP)

Contact-separation mode

Handmade

1 × 1

Voc ≈ 5 V

Isc ≈ 7 µA

P = 35 µW

Pdensity ≈ 35 µW cm−2

10 Hz
40 × 40

Voc ≈ 32.8 V

Isc ≈ 35 µA

P = 1148 µW

Pdensity ≈ 0.72 µW cm−2

Polydimethylsiloxane sponge with sugar assist [86]

Freestanding mode

Soft lithography + hand made

Voc ≈ 450 V

Isc ≈ 0.04 µA cm−2

Pdensity = 18 µW cm−2

400 N

5 Hz

Air-permeable paper-based TENG [91]

Contact-separation

Dip-coating + electrospinning + handmade

4 × 4

Voc ≈ 197 V

Isc ≈ 16.2 µA cm−2

P = 3191 µW cm−2

Pdensity = 797.85 µW cm−2

85 kPa
Egg white (EG) [89] Rice paper (RP)

Contact-separation

Handmade

1 × 2

Voc ≈ 55 V

Isc ≈ 0.6 µA cm−2

P = 33 µW cm−2

Pdensity = 16.5 µW cm−2

EG [89] Chitin

Contact-separation

Handmade

1 × 2

Voc ≈ 8 V

Isc ≈ 0.8 µA cm−2

P = 6.4 µW cm−2

Pdensity = 3.2 µW cm−2

Rice paper [90] Polyvinyl chloride PVC

Contact-separation

Brush coating + handmade

3 × 3

Voc ≈ 392 V

Isc ≈ 16.7 µA cm−2

Pdensity = 82.69 µW cm−2

Resistance = 80 Ω

5 Hz
Recombinant spider silk [97] PET

Contact-separation

Spin-coating + inkjet water lithography + handmade

48

Voc ≈ 2600 V

Isc ≈ 480 µA cm−2

Pdensity = 5290 µW cm−2

20 N

aThe peak value was used for the electric characterization

The TENGs using leaves are typically produced by hand, which is a problem for mass production and also limits their future use. However, the possibility of harvesting electric energy by plants highlights the idea of using natural triboelectric processes and renders a deeper understanding of the triboelectric effect designed by nature. The following section is focused on other possibilities to use natural materials, namely via by-products of plant processing. In these cases, the manufacture of TENGs can be carried out by additive technologies and liquid deposition, due to their adaptation capability of these methods.

Products of Plants Processing

Natural materials, such as cellulose and sugar, can be fabricated from plants and used for harvesting electric energy by the triboelectric effect. Both materials have intrinsic piezoelectric properties, which can be applied in hybrid harvesting systems [51, 65] that exploit both triboelectric and piezoelectric effects, such as biomedical sensors and actuators. Currently, the industrial production of these materials is well established. For example, cellulose fibers that are being used for paper manufacturing hold potential for energy harvesting applications [66, 67], as they are readily available and can be used for designing flexible devices [68]. Recently, Alam and Mandal [69] implemented a piezoelectric generator by mixing cellulose nanofibers and polydimethylsiloxane (PDMS) (as a matrix for cellulose) and observed the ability to produce up to 30 V and 500 nA by human-hand punching. As such, this material can be used in triboelectric generators or work as a triboelectric pair due to its high surface area [62]. Following this work, Peng et al. [70] constructed a TENG based on PDMS matrix, in which cellulose nanocrystals were used as fillers. This TENG was fabricated by the spin-coating method using an aluminum (Al) film as electrode. By performing tests in contact-separation mode and comparing its performance with a pure PDMS film with the same thickness, cellulose TENG provided voltages up to ~ 350 V, which correspond to a 10-fold increase as compared to pure PMDS. As pure cellulose can also be used for eco-friendly triboelectric generation, Parandeh et al. [71] proposed to use a cellulose paper as a triboelectric pair material with coated graphene oxide. They fabricated a book-shaped TENG working in the contact-separation mode, which was able to generate up to 120 V [71]. Hybrid cellulose paper was also used by Cui et al. [72]. In this study, cellulose nanofibril–phosphorene transparent paper of 10 µm thickness was fabricated (Fig. 3a). The TENG was designed using a polyethylene terephthalate (PET) film as a triboelectric pair. Mixing of cellulose nanofibrils with phosphorene emphasized the superior performance of this TENG (in comparison with pure cellulose nanofibrils) and protection of the phosphorene against oxidation. In addition, the TENG with a cellulose paper structure showed a decrease in electric output during fatigue tests (20% lower performance after 6 months). Since the stability of the natural materials constituting TENGs is an important feature for most applications, these tests must be always performed to characterize materials. In the past, cellulose was already used in TENGs as a part of an organic–inorganic composite. Shi et al. [73] fabricated a cellulose aerogel with BaTiO3 nanoparticles as fillers and coated it using a PDMS layer. The implemented flexible hybrid PENG-TENG nanogenerator was able to produce up to 48 V. Aerogels were also used in the harvester architecture (e.g., TENGs based on bacterial cellulose) [74]. Bacterial cellulose is produced by bacteria, specifically from the Acetobacter xylinum, as known since 1886 [75]. This material has been explored for self-powering systems based on piezoelectric transduction [76, 77]. Bacterial nanocellulose was used to fabricate a flexible, transparent and (even more important) bio- and an eco-friendly triboelectric nanogenerator [78] (Fig. 3b). Using a regenerated bacterial nanocellulose (BNC) film, such TENG was prepared via solubilization process from bacterial cellulose, which was in turn produced in a gel state by Acetobacter xylinum KJ1 in the Glu-Fruc medium. The performance of this TENG was sufficiently high: accumulative charge of ~ 8.1 µC m−2 and peak-power density of ~ 4.8 µW m−2. Moreover, Kim et al. [78] carried out additional characterization of the charge transfer by measuring the surface energy of materials under friction. The surface with lower surface energy is negatively charged after friction contact [7981]. Such characterization complements regular investigations of TENGs and allows deeper insight into the process of charge generation. Yao et al. [82] developed a TENG from thin transparent film based on cellulose nanofibers (CNF). In this work, a triboelectric pair was implemented using fluorinated ethylene propylene (FEP) (Fig. 3c). Moreover, the influence of the surface area on the TENG output performance was found. A significant increase in the open-circuit voltage was observed when the area was increased from 1 to 40 cm2 (spacer of 0.1 cm thickness). Such a TENG with the area of 1 × 1 cm2 was able to provide almost the same performance as standard polymer TENGs based on Kapton–PET and polytetrafluoroethylene (PTFE)–polyamide materials [18, 83].

Fig. 3.

Fig. 3

Products of processing of plants used to design TENGs: a cellulose/phosphorene hybrid TENG preparation and transparency demonstration. Reprinted with permission from Ref. [72]. Copyright (2017) Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim. b Demonstration of a bacterial nanocellulose-based TENG. Reprinted with permission from Ref. [78]. Copyright (2017) Published by Elsevier Ltd. c Surface structure, schematic illustration and demonstration of the transparency of a TENG based on cellulose nanofibrils. Reprinted with permission from Ref. [82]. Copyright (2016) Published by Elsevier Ltd. d Sponge TENG fabricated by 3D soft lithography using sugar particles. Reprinted with permission from Ref. [86]. Copyright (2016) Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim

Sugar is also a simple natural material that exhibits both piezoelectric and triboelectric properties, which are quite useful for energy harvesting applications [84]. Chun et al. [85] developed a sponge TENG based on PDMS with embedded Au nanoparticles. This sponge TENG was designed to work in a contact-separation mode. This work presented the novel approach to simplify the fabrication process based on replacement of a spacer by the pores. As sugar can be easily dissolved in water, it can be further explored using the soft lithography method. Kim et al. [86] manufactured the sponge TENG based on the sugar-polydimethylsiloxane composite, so that it was able to perform in a freestanding mode (Fig. 3d). The thin sponge-based TENG was tested using three different particles sizes. It turned out that the output characteristics were able to be controlled by the sugar filling and pore size. By changing the structure from flat to porous, it was possible to increase the output performance by five times, thus highlighting the effect of the sugar. Triboelectric transduction was also strongly influenced by the contact area and corresponding pore size. Filling the sponge with smaller particle size of the sugar seems to result in higher output characteristics. Park et al. [87] also highlighted the ability of this technology to produce a highly efficient TENG. A similar sponge TENG was engineered using sugar filling with the addition of ferroelectric nanoparticles [87].

Natural Biodegradable Materials

The first biodegradable triboelectric nanogenerator (BD-TENG) for short-term biomechanical energy conversion in vivo was developed in 2016 [88]. Due to the design of a multilayer structure, consisting of biodegradable polymers (BDP) and absorbable metals, this BD-TENG is able to decompose and dissolve in the animals’ body after the working cycle without any adverse long-term effect. Based on these results, fully bioabsorbable triboelectric nanogenerators (BN-TENGs) performing in vivo were developed by Jiang et al. [89]. A comprehensive research of “triboelectric series” of five natural bioresorbable materials was conducted by testing pairwise combinations, which significantly promoted the development of natural materials for TENGs and other triboelectric devices.

As shown in Fig. 4a, all polymeric components of BN-TENGs were manufactured from natural products, such as cellulose, chitin, silk fibroin (SF), rice paper (RP), and egg white (EW). Cellulose can be prepared from wood and cotton; chitin can be extracted from shells of crabs and shrimps; RP is usually obtained from wheat, corn, and rice; and EW and SF can be collected from eggs and cocoon, respectively. The as-prepared BN-TENG consisted of natural bioresorbable polymers (NBPs) and magnesium (Mg) electrodes with a vertical contact-separation mode (Fig. 4a). Any two different NBPs (NBP1 and NBP2) from chitin, cellulose, SF, RP, and EW could act as friction layers, and the ultrathin Mg films served as counter electrodes. The obtained nanostructure arrays were dense and homogeneous, with an average roughness of about 100 nm (Fig. 4a). Two NBP spacers were incorporated between the friction layers to effectively separate them. SF films were designed as encapsulation layers to protect the BN-TENG from the external environment. The maximum electric voltage, current, and power density reached was 55 V, 0.6 µA, and 21.6 mW m−2, respectively (Fig. 4a). The operation time of BN-TENGs in vitro and in vivo was controlled by the encapsulation of the silk fibroin film and could last from days to weeks. After its performance in Sprague–Dawley rats, this BN-TENG was fully degraded and resorbed, avoiding a second surgical procedure and other potential side effects. Using the proposed BN-TENGs as an electric voltage source to power an electric stimulation system in vitro, the function of isolated dysfunctional cardiomyocyte clusters was successfully controlled. The beating rates of cardiomyocyte clusters were accelerated, and the consistency of the cell contraction was improved. This solution provides a new approach to treat some heart diseases, such as bradycardia and arrhythmia.

Fig. 4.

Fig. 4

a NBPs obtained from wide raw material sources and structure diagram of a typical BN-TENG device: scanning electron microscopy (SEM) and atomic force microscopy (AFM) images of nanostructure on the surface of NBP film. Lower and upper scale bars: 5 and 1 µm. Reprinted with permission from Ref. [89]. Copyright (2018) Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim. b Photograph of the rice paper and scheme of the TENG: PET, PVC, transparent conductive electrode, and rice paper. Reprinted with permission from Ref. [90]. Copyright (2019) Published by Elsevier Ltd. c Electrical output of BD-TENG encapsulated in PVA. (c1, c2) Photograph of the implant site of PVA-coated BD-TENG. (c1) Right after implantation. (c2) 72 h after implantation. Reprinted with permission from Ref. [88]. Copyright (2016) AAAS. d In vivo exhibition of T2ENG’s multiple functions, such as total biodegradation, energy harvesting, biomechanical sensing, and medical therapy. Reprinted with permission from Ref. [96]. Copyright (2018) Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim

Recently, paper-based electronics has been introduced [90, 91] and since then, a significant importance was given to this topic. A novel rice paper-based biodegradable triboelectric nanogenerator (RP-TENG) was proposed [90], which is based on a single-electrode working mode (Fig. 4b). The biodegradable materials, such as rice paper and transparent conductive ink, were used as the triboelectric pairs and conductive electrode, respectively. Experimental tests yielded the values of open-circuit voltage (Voc), short-circuit current (Isc), and output power density of 244 V, 6 μA, and 37.64 μW cm−2, respectively. In addition, this fabricated RP-TENG was highly stable and recyclable. Finally, the electric energy generated by the RP-TENG could supply up to 45 commercial LEDs simultaneously. Further, the simple printer-paper TENG was fabricated by interlocking Kirigami patterns with maximum Voc of 115.49 V and Qtr of 39.87 nC [92].

A single-electrode lightweight TENG (E-TENG) using only edible materials was reported by Khandelwal et al. [93]. Laver coated with an edible silver leaf was used as the active film, and a rice sheet was selected as for the substrate. The surface potential, morphology, and roughness were analyzed. The laver was found triboelectrically active. The device was reabsorbed in phosphate-buffered saline (PBS) and gastric acid. The output performance was tested using paper, tissue paper, polyvinyl chloride (PVC), and fluorinated ethylene propylene (FEP). A FEP-laver E-TENG performed the best performance: electric voltage of 23 V and current of 315 nA. These electric signals were used to power several devices, such as hygrometers, wristwatches, green light-emitting diodes (LEDs), and ultraviolet (UV) LEDs.

Another highly promising material which is biocompatible, provides high mechanical strength and has a unique structure is spider silk [9496]. Zhang et al. [97] have demonstrated the potential of a TENG based on recombinant spider silk. The authors genetically engineered the triboelectric properties of spider silk and used water lithography to further modify the output performance. The surface modification by inkjet printing allowed both the fabrication of the rough surfaces and the transport of the doping agent (molecules, nanoparticles, and drugs). As a result, this TENG was able to provide a high power density of 5290 mW m−2 with 47.3% efficiency.

Application of Eco-Friendly and Biocompatible TENGs

Eco-friendly and biocompatible TENGs were mainly used to harvest electrical energy from the ambient. Various devices have been created and tested in a real environment. For example, the combination of fresh Hosta leaf with PMMA film demonstrated the possibility of designing TENGs based on structures that include leaves for both temperature sensing and powering of LEDs [62]. This kind of application shows that these TENGs hold potential for energy harvesting and to reuse polymers, which is an important advantage as polymers cannot be completely recyclable. Compatibility of TENGs with human skin allows their application as flexible devices working in a direct contact with the human body. Yang et al. [91] have also shown this ability for such kind of harvesters. Their paper-based TENG is air-permeable and washable, which is required for the contact with human skin.

Since most of natural materials are biocompatible, it is possible to use them for biosensors and monitoring of human biosignals. The function of isolated dysfunctional cardiomyocyte clusters was successfully regulated using silk fiber and magnesium films [89]. The in vivo and in vitro tests have shown a significant performance decrease from this implantable TENG during 24-h operation. Similar experiments have shown that poly(L-lactide-co-glycolide) (PLGA) and poly(caprolactone) (PCL)-based TENG are not functional after 72 h upon implantation in rats (Fig. 4c) [88]. Such kind of implantable devices with customized service time provides broad opportunities for therapy and disease diagnostics. Moreover, implantable TENG based on silk fibers can be used for drug delivery and epilepsy attack monitoring (Fig. 4d) [96]. Biocompatibility of silk fibers suggests their use as antibacterial patch [97]. The in vivo experiments have already demonstrated the antibacterial rate of 67.4% for bacteria Staphylococcus aureus by analyzing the infected wound throughout 7 days.

Overall Performance of TENGs Based on Natural Materials

Table 1 presents a broad range of studied triboelectric pairs based on natural leaves, plant materials, cellulose, and polymers and their performance. Analyzing the electric characteristics, one can conclude that the output voltage and current are influenced by material’s architecture and are strongly dependent on the measurement conditions. This fact suggests that the triboelectric effect is an intrinsic property of plants (from leaf to cellulose) and rigorous studies are needed to understand this phenomenon. Moreover, a unification of the test standards is required, so that the operation mode (contact-separation, single electrode, etc.) should follow similar methods to analyze different materials. Several studies demonstrated the importance of the measurement unification to identify TENGs mechanisms [29, 98, 99]. Unfortunately, many studies reported experimental tests in which TENGs were analyzed under different mechanical excitations (applied force and frequency) and size of samples (contact area), therefore not allowing an easy comparison. However, the energy characteristics are strongly dependent on the size and mechanical excitation (Fig. 5a, b, d). Different mechanical excitations used to study different TENGs perform more complex analyses. For example, the petal rose [60] and Rhododendron leaf [61] are able to provide 24 µW and 15 µW cm−2 for mechanical excitations of 2 Hz, 100 N, and 10 Hz, 0.9 N, respectively (Table 1). These observations emphasize highly nonlinear behavior of TENGs and demand establishing a standard for their testing. Following this approach, Jie et al. [62] investigated different leaves excited under the same conditions. By designing TENGs with the same area (8 × 8 cm2), they obtained the output electric power ranging from 180 to 2185 µW (Table 1) in different samples. Such experimental tests allow to understand the variations on the triboelectric behavior for different systems but demand deeper analyses of the mechanisms behind their excellent electric performances. It was shown that the performance of TENGs is not directly proportional to the device surface area. For example, increasing the device surfaces from 1 to 40 cm2 using cellulose nanofibrils leads to the increase in electric power from 35 to 1148 µW [82]. It is well known that the nonlinear dependence of power density and Isc in relation to the surface area can be explained by the surface inhomogeneity and edge effects. All these results demonstrated the ability of various natural materials to be used as elements in the TENGs architecture. It is worth noting that the polymers were always used as a supporting material (triboelectric pair or substrate). As such, polymers are nowadays required for advanced energy harvesting technologies: Their alloys are able to design customized forms of friction bodies [91, 100102] and to fabricate multilayer devices by different technologies providing uniform samples [74, 103105]. Limitations related to the ability of TENGs for eco-friendly harvesting and to be fully recycled are still unsolved and require more investigations and ecological tests. Indeed, the existing polymer materials can provide high performance and be reused, even if they are not fully recyclable. As biocompatible polymers allow to fabricate flexible devices, they can be applied as intracorporeal harvesters as well [88, 106, 107]. Importantly, for many of these applications, storage supercapacitors and conditioning circuits should be used together with implantable harvesters [108] considering the architecture of the biomedical systems [109]. Moreover, the investigation of different materials is demanded for detailed studies focused on the mechanism of triboelectric phenomenon, so that a general theory can be developed to explain and to predict properties, efficient combination of materials and performance. Besides, research efforts also demonstrate the possibilities of natural materials, which can be compared with inorganic materials in terms of electric performance [110, 111]. Additionally, natural materials can be used to mimic the design of architectures based on surface modification to enhance the triboelectric effect. Despite there are many reports focused on the design of TENGs, the rational selection of pair materials has not yet been achieved, highlighting the exhaustive comparison of harvester performances. Furthermore, the mechanism of charge formation is not well understood. For this reason, some studies provided additional characterization of materials [61, 78, 82]. Figure 5c demonstrates additional measurements of the contact angle. These studies allow to identify both wetting properties of the materials and their polarity: By increasing the contact angle, the polarity is shifted to a negative charge. The contact angle is a macroscopic measure of wettability, which additionally characterizes the triboelectric material before analyzing the performance of TENGs. In this context, it is worth noting that Kelvin probe force microscopy can be also used to characterize polar properties. Figure 5e shows an example of the charge distribution on the TENG surface before and after the touch stimulus. This is a relevant experiment as it allows to investigate the mechanism of charge transfer in triboelectric effect and the influence of dehydration in a leaf during friction [61]. These measurements demonstrate that leaf drying decouples the actual energy conversion site, the cuticle, from the charge transport circuit that exists in the hydrated living tissue.

Fig. 5.

Fig. 5

Factors influencing the output performance of TENGs: a influence of the excitation frequency. b The output voltage as a function of the size contact area of TENGs. Reprinted with permission from Ref. [82]. Copyright (2016) Published by Elsevier Ltd. c Static water contact angle measurement and contact potential difference comparison of materials under friction. Reprinted with permission from Ref. [78] Copyright (2017) Published by Elsevier Ltd. d Influence of the vertical force on output voltage. Reprinted with permission from Ref. [86]. Copyright (2016) Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim; e Kelvin probe force microscopy of the leaf before and after friction. Reprinted with permission from Ref. [61] Copyright (2018) Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim

Conclusions

This review demonstrates the potential of the natural materials in energy harvesting systems. Investigation of the TENGs and combination of different kinds of materials allow to foster the fundamental knowledge, materials application, and their characterization methods. By this way, new energy harvesting systems can be applied in a safe manner for the environment. Using various materials around us, we can create eco-friendly, biocompatible, and highly efficient devices. The overviewed literature highlights that a wide range of materials, harvester architectures, and investigation methods were already proposed. These methods show how the harvesting efficiency is influenced by the pair material, contact area, thickness, and mechanical excitation (force and frequency), etc. The novel nanotechnological methods allow a deeper understanding of the charge formation, friction materials dependence, and triboelectricity at the nanoscale. New testing methods for TENG characterization are being implemented to achieve these goals. Various methods under investigation will most likely allow to understand the charge formation and the mechanism of the triboelectric phenomenon in the forthcoming years. Using natural materials incorporated within TENGs will propel the development of innovative energy harvesting systems fully recyclable, eco-friendly, and biocompatible.

Acknowledgements

This work was developed within the scope of the project CICECO-Aveiro Institute of Materials, refs. UIDB/50011/2020 & UIDP/50011/2020, financed by national funds through the FCT/MEC. S.K. and A.K. were partly supported by FCT (Portugal) through the project “BioPiezo”- PTDC/CTM–CTM/31679/2017 (CENTRO-01-0145-FEDER-031679). M. Soares dos Santos was also supported by FCT, through the grant reference SFRH/BPD/117475/2016. All authors were partly supported by FCT through the project “SelfMED” (POCI-01-0145-FEDER-031132). Part of this work was funded by national funds (OE), through FCT—Fundação para a Ciência e a Tecnologia, I.P., in the scope of the framework contract foreseen in the numbers 4, 5, and 6 of the article 23, of the Decree-Law 57/2016, of August 29, changed by Law 57/2017, of July 19. The research was also supported by the Ministry of Education and Science of the Russian Federation in the framework of the Increase Competitiveness Program of NUST « MISiS » (No. K2-2019-015).

References

  • 1.J. Kymissis, C. Kendall, J. Paradiso, N. Gershenfeld, Parasitic power harvesting in shoes, in Digest of Papers Second International Symposium on Wearable Computers, pp. 132–139 (1998). 10.1109/ISWC.1998.729539
  • 2.Li S, Zhong Q, Zhong J, Cheng X, Wang B, et al. Cloth-based power shirt for wearable energy harvesting and clothes ornamentation. ACS Appl. Mater. Interfaces. 2015;7(27):14912–14916. doi: 10.1021/acsami.5b03680. [DOI] [PubMed] [Google Scholar]
  • 3.Liu GX, Li WJ, Liu WB, Bu TZ, Guo T, et al. Soft tubular triboelectric nanogenerator for biomechanical energy harvesting. Adv. Sustain. Syst. 2018;2(12):1800081. doi: 10.1002/adsu.201800081. [DOI] [Google Scholar]
  • 4.Hou T-C, Yang Y, Zhang H, Chen J, Chen L-J, et al. Triboelectric nanogenerator built inside shoe insole for harvesting walking energy. Nano Energy. 2013;2(5):856–862. doi: 10.1016/j.nanoen.2013.03.001. [DOI] [Google Scholar]
  • 5.Soares dos Santos MP, Ferreira JAF, Simões JAO, Pascoal R, Torrão J, et al. Magnetic levitation-based electromagnetic energy harvesting: a semi-analytical non-linear model for energy transduction. Sci. Rep. 2016;6(1):18579. doi: 10.1038/srep18579. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 6.Soares dos Santos MP, Marote A, Santos T, Torrão J, Ramos A, et al. New cosurface capacitive stimulators for the development of active osseointegrative implantable devices. Sci. Rep. 2016;6(1):30231. doi: 10.1038/srep30231. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 7.Harne RL, Schoemaker ME, Dussault BE, Wang KW. Wave heave energy conversion using modular multistability. Appl. Energy. 2014;130:148–156. doi: 10.1016/j.apenergy.2014.05.038. [DOI] [Google Scholar]
  • 8.Wang X, Wang ZL, Yang Y. Hybridized nanogenerator for simultaneously scavenging mechanical and thermal energies by electromagnetic-triboelectric-thermoelectric effects. Nano Energy. 2016;26:164–171. doi: 10.1016/j.nanoen.2016.05.032. [DOI] [Google Scholar]
  • 9.Shen Q, Xie X, Peng M, Sun N, Shao H, et al. Self-powered vehicle emission testing system based on coupling of triboelectric and chemoresistive effects. Adv. Funct. Mater. 2018;28(10):1703420. doi: 10.1002/adfm.201703420. [DOI] [Google Scholar]
  • 10.Engers DA, Fricke MN, Newman AW, Morris KR. Triboelectric charging and dielectric properties of pharmaceutically relevant mixtures. J. Electrostat. 2007;65(9):571–581. doi: 10.1016/j.elstat.2006.12.002. [DOI] [Google Scholar]
  • 11.Wasem JV, LaMarche BL, Langford SC, Dickinson JT. Triboelectric charging of a perfluoropolyether lubricant. J. Appl. Phys. 2003;93(4):2202–2207. doi: 10.1063/1.1536011. [DOI] [Google Scholar]
  • 12.Sakaguchi M, Shimada S, Kashiwabara H. Mechanoions produced by mechanical fracture of solid polymer. 6. A generation mechanism of triboelectricity due to the reaction of mechanoradicals with mechanoanions on the friction surface. Macromolecules. 1990;23(23):5038–5040. doi: 10.1021/ma00225a027. [DOI] [Google Scholar]
  • 13.Sakaguchi M, Kashiwabara H. A generation mechanism of triboelectricity due to the reaction of mechanoradicals with mechanoions which are produced by mechanical fracture of solid polymer‎. Colloid Polym. Sci. 1992;270(7):621–626. doi: 10.1007/BF00654038. [DOI] [Google Scholar]
  • 14.Lungu M. Electrical separation of plastic materials using the triboelectric effect. Miner. Eng. 2004;17(1):69–75. doi: 10.1016/j.mineng.2003.10.010. [DOI] [Google Scholar]
  • 15.Mountain JR, Mazumder MK, Sims RA, Wankum DL, Chasser T, et al. Triboelectric charging of polymer powders in fluidization and transport processes. IEEE Trans. Ind. Appl. 2001;37(3):778–784. doi: 10.1109/28.924759. [DOI] [Google Scholar]
  • 16.Yair Y. Charge generation and separation processes. Space Sci. Rev. 2008;137(1–4):119–131. doi: 10.1007/s11214-008-9348-x. [DOI] [Google Scholar]
  • 17.Lacks DJ, Levandovsky A. Effect of particle size distribution on the polarity of triboelectric charging in granular insulator systems. J. Electrostat. 2007;65(2):107–112. doi: 10.1016/j.elstat.2006.07.010. [DOI] [Google Scholar]
  • 18.Fan F-R, Tian Z-Q, Wang ZL. Flexible triboelectric generator. Nano Energy. 2012;1(2):328–334. doi: 10.1016/j.nanoen.2012.01.004. [DOI] [Google Scholar]
  • 19.Chen B, Yang Y, Wang ZL. Scavenging wind energy by triboelectric nanogenerators. Adv. Energy Mater. 2018;8(10):1702649. doi: 10.1002/aenm.201702649. [DOI] [PubMed] [Google Scholar]
  • 20.Chandrasekhar A, Vivekananthan V, Khandelwal G, Kim SJ. Sustainable human-machine interactive triboelectric nanogenerator toward a smart computer mouse. ACS Sustain. Chem. Eng. 2019;7(7):7177–7182. doi: 10.1021/acssuschemeng.9b00175. [DOI] [Google Scholar]
  • 21.Chandrasekhar A, Khandelwal G, Alluri NR, Vivekananthan V, Kim SJ. Battery-free electronic smart toys: a step toward the commercialization of sustainable triboelectric nanogenerators. ACS Sustain. Chem. Eng. 2018;6(5):6110–6116. doi: 10.1021/acssuschemeng.7b04769. [DOI] [Google Scholar]
  • 22.Chandrasekhar A, Vivekananthan V, Khandelwal G, Kim SJ. A fully packed water-proof, humidity resistant triboelectric nanogenerator for transmitting morse code. Nano Energy. 2019;60:850–856. doi: 10.1016/j.nanoen.2019.04.004. [DOI] [Google Scholar]
  • 23.Wang ZL, Lin L, Chen J, Niu S, Zi Y. Triboelectric Nanogenerators. Basel: Springer; 2017. p. 517. [Google Scholar]
  • 24.Li L, Liu S, Tao X, Song J. Triboelectric performances of self-powered, ultra-flexible and large-area poly(dimethylsiloxane)/Ag-coated chinlon composites with a sandpaper-assisted surface microstructure. J. Mater. Sci. 2019;54(10):7823–7833. doi: 10.1007/s10853-019-03428-5. [DOI] [Google Scholar]
  • 25.Kim D, Jeon S-B, Kim JY, Seol M-L, Kim SO, et al. High-performance nanopattern triboelectric generator by block copolymer lithography. Nano Energy. 2015;12:331–338. doi: 10.1016/j.nanoen.2015.01.008. [DOI] [Google Scholar]
  • 26.Šutka A, Mālnieks K, Lapčinskis L, Kaufelde P, Linarts A, et al. The role of intermolecular forces in contact electrification on polymer surfaces and triboelectric nanogenerators. Energy Environ. Sci. 2019;12(8):2417–2421. doi: 10.1039/C9EE01078E. [DOI] [Google Scholar]
  • 27.Cezan SD, Nalbant AA, Buyuktemiz M, Dede Y, Baytekin HT, et al. Control of triboelectric charges on common polymers by photoexcitation of organic dyes. Nat. Commun. 2019;10:276. doi: 10.1038/s41467-018-08037-5. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 28.Musa UG, Cezan SD, Baytekin B, Baytekin HT. The charging events in contact-separation electrification. Sci. Rep. 2018;8:2472. doi: 10.1038/s41598-018-20413-1. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 29.Zou H, Zhang Y, Guo L, Wang P, He X, et al. Quantifying the triboelectric series. Nat. Commun. 2019;10:1427. doi: 10.1038/s41467-019-09461-x. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 30.Wang S, Lin L, Wang ZL. Nanoscale triboelectric-effect-enabled energy conversion for sustainably powering portable electronics. Nano Lett. 2012;12(12):6339–6346. doi: 10.1021/nl303573d. [DOI] [PubMed] [Google Scholar]
  • 31.Yun BK, Kim JW, Kim HS, Jung KW, Yi Y, et al. Base-treated polydimethylsiloxane surfaces as enhanced triboelectric nanogenerators. Nano Energy. 2015;15:523–529. doi: 10.1016/j.nanoen.2015.05.018. [DOI] [Google Scholar]
  • 32.Ruhe J. And there was light: prospects for the creation of micro- and nanostructures through maskless photolithography. ACS Nano. 2017;11(9):8537–8541. doi: 10.1021/acsnano.7b05593. [DOI] [PubMed] [Google Scholar]
  • 33.Ko YH, Lee SH, Leem JW, Yu JS. High transparency and triboelectric charge generation properties of nano-patterned PDMS. RSC Adv. 2014;4:10216–10220. doi: 10.1039/c3ra47199c. [DOI] [Google Scholar]
  • 34.Wang P, Liu R, Ding W, Zhang P, Pan I, et al. Complementary electromagnetic-triboelectric active sensor for detecting multiple mechanical triggering. Adv. Funct. Mater. 2018;28(11):1705808. doi: 10.1002/adfm.201705808. [DOI] [Google Scholar]
  • 35.Lin Z-H, Zhu G, Zhou YS, Yang Y, Bai P, et al. A self-powered triboelectric nanosensor for mercury ion detection. Angew. Chem. Int. Ed. 2013;52(19):5065–5069. doi: 10.1002/anie.201300437. [DOI] [PubMed] [Google Scholar]
  • 36.Zhu G, Lin Z-H, Jing Q, Bai P, Pan C, et al. Toward large-scale energy harvesting by a nanoparticle-enhanced triboelectric nanogenerator. Nano Lett. 2013;13(2):847–853. doi: 10.1021/nl4001053. [DOI] [PubMed] [Google Scholar]
  • 37.Lin L, Wang S, Xie Y, Jing Q, Niu S, et al. Segmentally structured disk triboelectric nanogenerator for harvesting rotational mechanical energy. Nano Lett. 2013;13(6):2916–2923. doi: 10.1021/nl4013002. [DOI] [PubMed] [Google Scholar]
  • 38.Jing Q, Zhu G, Bai P, Xie Y, Chen J, et al. Case-encapsulated triboelectric nanogenerator for harvesting energy from reciprocating sliding motion. ACS Nano. 2014;8(4):3836–3842. doi: 10.1021/nn500694y. [DOI] [PubMed] [Google Scholar]
  • 39.Zhu G, Pan C, Guo W, Chen C-Y, Zhou Y, et al. Triboelectric-generator-driven pulse electrodeposition for micropatterning. Nano Lett. 2012;12(9):4960–4965. doi: 10.1021/nl302560k. [DOI] [PubMed] [Google Scholar]
  • 40.Zhang R, Hummelgård M, Örtegren J, Olsen M, Andersson H, et al. Interaction of the human body with triboelectric nanogenerators. Nano Energy. 2019;57:279–292. doi: 10.1016/j.nanoen.2018.12.059. [DOI] [Google Scholar]
  • 41.O. Rubes, Z. Hadas, Design and simulation of bistable piezoceramic cantilever for energy harvesting from slow swinging movement, in IEEE 18th International Power Electronics and Motion Control Conference (PEMC), pp. 663–668 (2018). 10.1109/EPEPEMC.2018.8521846
  • 42.Cui HC, Hensleigh R, Yao DS, Maurya D, Kumar P, et al. Three-dimensional printing of piezoelectric materials with designed anisotropy and directional response. Nat. Mater. 2019;18:234–241. doi: 10.1038/s41563-018-0268-1. [DOI] [PubMed] [Google Scholar]
  • 43.Khan Y, Ostfeld AE, Lochner CM, Pierre A, Arias AC. Monitoring of vital signs with flexible and wearable medical devices. Adv. Mater. 2016;28(22):4373–4395. doi: 10.1002/adma.201504366. [DOI] [PubMed] [Google Scholar]
  • 44.Cadei A, Dionisi A, Sardini E, Serpelloni M. Kinetic and thermal energy harvesters for implantable medical devices and biomedical autonomous sensors. Meas. Sci. Technol. 2014;25:012003. doi: 10.1088/09570233/25/1/012003. [DOI] [Google Scholar]
  • 45.Hosseini NR, Lee J-S. Biocompatible and flexible chitosan-based resistive switching memory with magnesium electrodes. Adv. Funct. Mater. 2015;25(35):5586–5592. doi: 10.1002/adfm.201502592. [DOI] [Google Scholar]
  • 46.Zhu W-K, Cong H-P, Yao H-B, Mao L-B, Asiri AM. Bioinspired, ultrastrong, highly biocompatible, and bioactive natural polymer/graphene oxide nanocomposite films. Small. 2015;11(34):4298–4302. doi: 10.1002/smll.201500486. [DOI] [PubMed] [Google Scholar]
  • 47.Lee SY, Tan ST, Cheong KW, Ming KK, Heng YX, et al. Development of biocompatible natural rubber latex film incorporated with vegetable oil microemulsion as plasticizer: effect of curing conditions. AIP Conf. Proc. 2018;1985:040004. doi: 10.1063/1.5047181. [DOI] [Google Scholar]
  • 48.Yu Y, Wang X. Chemical modification of polymer surfaces for advanced triboelectric nanogenerator development. Extreme Mech. Lett. 2016;9(3):514–530. doi: 10.1016/j.eml.2016.02.019. [DOI] [Google Scholar]
  • 49.Wang S, Zi Y, Zhou YS, Li S, Fan F, et al. Molecular surface functionalization to enhance the power output of triboelectric nanogenerators. J. Mater. Chem. A. 2016;4:3728–3734. doi: 10.1039/C5TA10239A. [DOI] [Google Scholar]
  • 50.Shin S-H, Kwon YH, Kim Y-H, Jung J-Y, Lee MH, et al. Triboelectric charging sequence induced by surface functionalization as a method to fabricate high performance triboelectric generators. ACS Nano. 2015;9(4):4621–4627. doi: 10.1021/acsnano.5b01340. [DOI] [PubMed] [Google Scholar]
  • 51.Rajala S, Siponkoski T, Sarlin E, Mettänen M, Vuoriluoto M, et al. Cellulose nanofibril film as a piezoelectric sensor material. ACS Appl. Mater. Interfaces. 2016;8(24):15607–15614. doi: 10.1021/acsami.6b03597. [DOI] [PubMed] [Google Scholar]
  • 52.Tan E-L, Potroz MG, Ferracci G, Jackman JA, Jung H, et al. Light-induced surface modification of natural plant microparticles: toward colloidal science and cellular adhesion applications. Adv. Funct. Mater. 2018;28(18):1707568. doi: 10.1002/adfm.201707568. [DOI] [Google Scholar]
  • 53.K. Liu, J. Jiang, Z. Zhou, X. Cai, H. Tao et al., Silk: new opportunities for an ancient material in MEMS/NEMS, in IEEE 29th International Conference on Micro Electro Mechanical Systems (MEMS), pp. 558–560 (2016). 10.1109/MEMSYS.2016.7421686
  • 54.Seol M-L, Woo J-H, Lee D-I, Im H, Hur J, et al. Nature-replicated nano-in-micro structures for triboelectric energy harvesting. Small. 2014;10(19):3887–3894. doi: 10.1002/smll.201400863. [DOI] [PubMed] [Google Scholar]
  • 55.Fang ZQ, Zhu HL, Yuan YB, Ha D, Zhu SZ, et al. Novel nanostructured paper with ultrahigh transparency and ultrahigh haze for solar cells. Nano Lett. 2014;14(2):765–773. doi: 10.1021/nl404101p. [DOI] [PubMed] [Google Scholar]
  • 56.Jung YH, Chang T-H, Zhang H, Yao C, Zheng Q, et al. High-performance green flexible electronics based on biodegradable cellulose nanofibril paper. Nat. Commun. 2015;6:7170. doi: 10.1038/ncomms8170. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 57.He X, Guo H, Yue X, Gao J, Xi Y, et al. Improving energy conversion efficiency for triboelectric nanogenerator with capacitor structure by maximizing surface charge density. Nanoscale. 2015;7:1896–1903. doi: 10.1039/C4NR05512H. [DOI] [PubMed] [Google Scholar]
  • 58.Lee JH, Hinchet R, Kim SK, Kim S, Kim S-W. Shape memory polymer-based self-healing triboelectric nanogenerator. Energy Environ. Sci. 2015;8:3605–3613. doi: 10.1039/C5EE02711J. [DOI] [Google Scholar]
  • 59.Sun J-G, Yang T-N, Wang C-Y, Chen L-J. A flexible transparent one-structure tribo-piezo-pyroelectric hybrid energy generator based on bio-inspired silver nanowires network for biomechanical energy harvesting and physiological monitoring. Nano Energy. 2018;48:383–390. doi: 10.1016/j.nanoen.2018.03.071. [DOI] [Google Scholar]
  • 60.Chen Y, Jie Y, Wang J, Ma J, Jia X, et al. Triboelectrification on natural rose petal for harvesting environmental mechanical energy. Nano Energy. 2018;50:441–447. doi: 10.1016/j.nanoen.2018.05.021. [DOI] [Google Scholar]
  • 61.Meder F, Must I, Sadeghi A, Mondini A, Filippeschi C, et al. Energy conversion at the cuticle of living plants. Adv. Funct. Mater. 2018;28(51):1806689. doi: 10.1002/adfm.201806689. [DOI] [Google Scholar]
  • 62.Jie Y, Jia X, Zou J, Chen Y, Wang N, et al. Natural leaf made triboelectric nanogenerator for harvesting environmental mechanical energy. Adv. Energy Mater. 2018;8(12):1703133. doi: 10.1002/aenm.201703133. [DOI] [Google Scholar]
  • 63.Feng Y, Zhang I, Zheng Y, Wang D, Zhou F, et al. Leaves based triboelectric nanogenerator (TENG) and TENG tree for wind energy harvesting. Nano Energy. 2019;55:260–268. doi: 10.1016/j.nanoen.2018.10.075. [DOI] [Google Scholar]
  • 64.Choi D, Kim DW, Yoo D, Cha KJ, La M, et al. Spontaneous occurrence of liquid-solid contact electrification in nature: toward a robust triboelectric nanogenerator inspired by the natural lotus leaf. Nano Energy. 2017;36:250–259. doi: 10.1016/j.nanoen.2017.04.026. [DOI] [Google Scholar]
  • 65.Pohanka M. The piezoelectric biosensors: principles and applications a review. Int. J. Electrochem. Sci. 2017;12:496–506. doi: 10.20964/2017.01.44. [DOI] [Google Scholar]
  • 66.Fu R, Chen S, Lin Y, Zhang S, Jiang J, et al. Improved piezoelectric properties of electrospun poly(vinylidene fluoride) fibers blended with cellulose nanocrystals. Mater. Lett. 2017;187:86–88. doi: 10.1016/j.matlet.2016.10.068. [DOI] [Google Scholar]
  • 67.S. Tuukkanen, S. Rajala, Nanocellulose as a piezoelectric material. PiezoelectricityOrganic and Inorganic Materials and Applications. IntechOpen (2018). 10.5772/intechopen.77025
  • 68.Zheng Q, Zhang H, Mi H, Cai Z, Ma Z, et al. High-performance flexible piezoelectric nanogenerators consisting of porous cellulose nanofibril (CNF)/poly(dimethylsiloxane) (PDMS) aerogel films. Nano Energy. 2016;26:504–512. doi: 10.1016/j.nanoen.2016.06.009. [DOI] [Google Scholar]
  • 69.Alam MM, Mandal D. Native cellulose microfiber-based hybrid piezoelectric generator for mechanical energy harvesting utility. ACS Appl. Mater. Interfaces. 2016;8(3):1555–1558. doi: 10.1021/acsami.5b08168. [DOI] [PubMed] [Google Scholar]
  • 70.Peng J, Zhang H, Zheng Q, Clemons CM, Sabo RC, et al. A composite generator film impregnated with cellulose nanocrystals for enhanced triboelectric performance. Nanoscale. 2017;9(4):1428–1433. doi: 10.1039/C6NR07602E. [DOI] [PubMed] [Google Scholar]
  • 71.Parandeh S, Kharaziha M, Karimzadeh F. An eco-friendly triboelectric hybrid nanogenerators based on graphene oxide incorporated polycaprolactone fibers and cellulose paper. Nano Energy. 2019;59:412–421. doi: 10.1016/j.nanoen.2019.02.058. [DOI] [Google Scholar]
  • 72.Cui P, Parida K, Lin M-F, Xiong J, Cai G, et al. Transparent, flexible cellulose nanofibril-phosphorene hybrid paper as triboelectric nanogenerator. Adv. Mater. Interfaces. 2017;4(22):1700651. doi: 10.1002/admi.201700651. [DOI] [Google Scholar]
  • 73.Shi K, Huang X, Sun B, Wu Z, He J, et al. Cellulose/BaTiO3 aerogel paper based flexible piezoelectric nanogenerators and the electric coupling with triboelectricity. Nano Energy. 2019;57:450–458. doi: 10.1016/j.nanoen.2018.12.076. [DOI] [Google Scholar]
  • 74.Seol M-L, Han J-W, Moon D-I, Yoon KJ, Hwang CS, et al. All-printed triboelectric nanogenerator. Nano Energy. 2018;44:82–88. doi: 10.1016/j.nanoen.2017.11.067. [DOI] [Google Scholar]
  • 75.Fontana JD, Desouza AM, Fontana CK, Torriani IL, Moreschi JC, et al. Acetobacter cellulose pellicle as a temporary skin substitute. Appl. Biochem. Biotechnol. 1990;24(1):253–264. doi: 10.1007/bf02920250. [DOI] [PubMed] [Google Scholar]
  • 76.Zhang G, Liao Q, Zhang Z, Liang Q, Zhao Y, et al. Novel piezoelectric paper-based flexible nanogenerators composed of BaTiO3 nanoparticles and bacterial cellulose. Adv. Sci. 2016;3(2):1500257. doi: 10.1002/advs.201500257. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 77.Wan S, Li T, Chen CJ, Kong WQ, Zhu SZ, et al. Transparent, anisotropic biofilm with aligned bacterial cellulose nanofibers. Adv. Funct. Mater. 2018;28(24):1707491. doi: 10.1002/adfm.201707491. [DOI] [Google Scholar]
  • 78.Kim H-J, Yim E-C, Kim J-H, Kim S-J, Park J-Y, et al. Bacterial nano-cellulose triboelectric nanogenerator. Nano Energy. 2017;33:130–137. doi: 10.1016/j.nanoen.2017.01.035. [DOI] [Google Scholar]
  • 79.Greason WD, Oltean IM, Kucerovsky Z, Ieta AC. Triboelectric charging between polytetrafluoroethylene and metals. IEEE Trans. Ind. Appl. 2004;40(2):442–450. doi: 10.1109/tia.2004.824439. [DOI] [Google Scholar]
  • 80.Dwari RK, Rao KH, Somasundaran P. Characterisation of particle tribo-charging and electron transfer with reference to electrostatic dry coal cleaning. Int. J. Miner. Process. 2009;91(3–4):100–110. doi: 10.1016/j.minpro.2009.02.006. [DOI] [Google Scholar]
  • 81.Bai P, Zhu G, Zhou YS, Wang SH, Ma JS, et al. Dipole-moment-induced effect on contact electrification for triboelectric nanogenerators. Nano Res. 2014;7(7):990–997. doi: 10.1007/s12274-014-0461-8. [DOI] [Google Scholar]
  • 82.Yao C, Hernandez A, Yu Y, Cai Z, Wang X. Triboelectric nanogenerators and power-boards from cellulose nanofibrils and recycled materials. Nano Energy. 2016;30:103–108. doi: 10.1016/j.nanoen.2016.09.036. [DOI] [Google Scholar]
  • 83.Yang Y, Zhang H, Liu R, Wen X, Hou T-C, et al. Fully enclosed triboelectric nanogenerators for applications in water and harsh environments. Adv. Energy Mater. 2013;3(12):1563–1568. doi: 10.1002/aenm.201300376. [DOI] [Google Scholar]
  • 84.Maity K, Garain S, Henkel K, Schmeißer D, Mandal D. Natural sugar-assisted, chemically reinforced, highly durable piezoorganic nanogenerator with superior power density for self-powered wearable electronics. ACS Appl. Mater. Interfaces. 2018;10(50):44018–44032. doi: 10.1021/acsami.8b15320. [DOI] [PubMed] [Google Scholar]
  • 85.Chun J, Kim JW, Jung W-S, Kang C-Y, Kim S-W, et al. Mesoporous pores impregnated with au nanoparticles as effective dielectrics for enhancing triboelectric nanogenerator performance in harsh environments. Energy Environ. Sci. 2015;8:3006–3012. doi: 10.1039/C5EE01705J. [DOI] [Google Scholar]
  • 86.Kim D, Park S-J, Jeon S-B, Seol M-L, Choi Y-K. A triboelectric sponge fabricated from a cube sugar template by 3D soft lithography for superhydrophobicity and elasticity. Adv. Electron. Mater. 2016;2(4):1500331. doi: 10.1002/aelm.201500331. [DOI] [Google Scholar]
  • 87.Park D, Shin S-H, Yoon I-J, Nah J. Ferroelectric nanoparticle-embedded sponge structure triboelectric generators. Nanotechnology. 2018;29(18):185402. doi: 10.1088/1361-6528/aaafa3. [DOI] [PubMed] [Google Scholar]
  • 88.Zheng Q, Zou Y, Zhang Y, Liu Z, Shi B, et al. Biodegradable triboelectric nanogenerator as a life-time designed implantable power source. Sci. Adv. 2016;2(3):e1501478. doi: 10.1126/sciadv.1501478. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 89.Jiang W, Li H, Liu Z, Li Z, Tian J, et al. Fully bioabsorbable natural-materials-based triboelectric nanogenerators. Adv. Mater. 2018;30(32):e1801895. doi: 10.1002/adma.201801895. [DOI] [PubMed] [Google Scholar]
  • 90.Chi Y, Xia K, Zhu Z, Fu J, Zhang H, et al. Rice paper-based biodegradable triboelectric nanogenerator. Microelectron. Eng. 2019;216:111059. doi: 10.1016/j.mee.2019.111059. [DOI] [Google Scholar]
  • 91.Yang W, Cao R, Zhang X, Li H, Li C. Air-permeable and washable paper-based triboelectric nanogenerator based on highly flexible and robust paper electrodes. Adv. Mater. Technol. 2018;3(11):1800178. doi: 10.1002/admt.201800178. [DOI] [Google Scholar]
  • 92.Wu C, Wang X, Lin L, Guo H, Wang ZL. Paper-based triboelectric nanogenerators made of stretchable interlocking kirigami patterns. ACS Nano. 2016;10(4):4652–4659. doi: 10.1021/acsnano.6b00949. [DOI] [PubMed] [Google Scholar]
  • 93.Khandelwal G, Minocha T, Yadav SK, Chandrasekhar A, Raj MJ, et al. All edible materials derived biocompatible and biodegradable triboelectric nanogenerator. Nano Energy. 2019;65:104016. doi: 10.1016/j.nanoen.2019.104016. [DOI] [Google Scholar]
  • 94.Ulasevich SA, Nenashkina AV, Ryzhkov NV, Kiselev G, Nikolaeva V, et al. Natural silk film for magnesium protection: Hydrophobic/hydrophilic interaction and self-healing effect. Macromol. Mater. Eng. 2019 doi: 10.1002/mame.201900412. [DOI] [Google Scholar]
  • 95.Fredriksson C, Hedhammar M, Feinstein R, Nordling K, Kratz G, et al. Tissue response to subcutaneously implanted recombinant spider silk: an in vivo study. Materials. 2009;2(4):1908–1922. doi: 10.3390/ma2041908. [DOI] [Google Scholar]
  • 96.Zhang Y, Zhou Z, Fan Z, Zhang S, Zheng F, et al. Self-powered multifunctional transient bioelectronics. Small. 2018;14(35):1802050. doi: 10.1002/smll.201802050. [DOI] [PubMed] [Google Scholar]
  • 97.Zhang Y, Zhou Z, Sun L, Liu Z, Xia X, et al. “Genetically engineered” biofunctional triboelectric nanogenerators using recombinant spider silk. Adv. Mater. 2018;30(50):1805722. doi: 10.1002/adma.201805722. [DOI] [PubMed] [Google Scholar]
  • 98.Xu C, Zi Y, Wang AC, Zou H, Dai Y, et al. On the electron-transfer mechanism in the contact-electrification effect. Adv. Mater. 2018;30(15):1706790. doi: 10.1002/adma.201706790. [DOI] [PubMed] [Google Scholar]
  • 99.Zi Y, Niu S, Wang J, Zhen W, Tang W, et al. Standards and figure-of-merits for quantifying the performance of triboelectric nanogenerators. Nat. Commun. 2015;6:8376. doi: 10.1038/ncomms9376. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 100.Zhao Y, Fan H, Ren X, Long C, Liu G, et al. Lead-free Bi5−xLaxTi3FeO15 (x = 0, 1) nanofibers toward wool keratin-based biocompatible piezoelectric nanogenerators. J. Mater. Chem. C. 2016;4:7324–7331. doi: 10.1039/C6TC01828A. [DOI] [Google Scholar]
  • 101.Yan J, Liu M, Jeong YG, Kang W, Li L, et al. Performance enhancements in poly(vinylidene fluoride)-based piezoelectric nanogenerators for efficient energy harvesting. Nano Energy. 2019;56:662–692. doi: 10.1016/j.nanoen.2018.12.010. [DOI] [Google Scholar]
  • 102.Xiao TX, Jiang T, Zhu JX, Liang X, Xu L, et al. Silicone-based triboelectric nanogenerator for water wave energy harvesting. ACS Appl. Mater. Interfaces. 2018;10(4):3616–3623. doi: 10.1021/acsami.7b17239. [DOI] [PubMed] [Google Scholar]
  • 103.Jang S, Kim H, Oh JH. Simple and rapid fabrication of pencil-on-paper triboelectric nanogenerators with enhanced electrical performance. Nanoscale. 2017;9:13034–13041. doi: 10.1039/C7NR04610C. [DOI] [PubMed] [Google Scholar]
  • 104.Shin S-Y, Saravanakumar B, Ramadoss A, Kim SJ. Fabrication of PDMS-based triboelectric nanogenerator for self-sustained power source application. Int. J. Energy Res. 2016;40(3):288–297. doi: 10.1002/er.3376. [DOI] [Google Scholar]
  • 105.Luo Z, Li Y, Duan C, Wang B. Fabrication of a superhydrophobic mesh based on PDMS/SiO2 nanoparticles/PVDF microparticles/KH-550 by one-step dip-coating method. RSC Adv. 2018;8:16251–16259. doi: 10.1039/C8RA03262A. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 106.Zheng Q, Shi B, Fan F, Wang X, Yan L, et al. In vivo powering of pacemaker by breathing-driven implanted triboelectric nanogenerator. Adv. Mater. 2014;26(33):5851–5856. doi: 10.1002/adma.201402064. [DOI] [PubMed] [Google Scholar]
  • 107.Zheng Q, Zhang H, Shi B, Xue X, Liu Z, et al. In vivo self-powered wireless cardiac monitoring via implantable triboelectric nanogenerator. ACS Nano. 2016;10(7):6510–6518. doi: 10.1021/acsnano.6b02693. [DOI] [PubMed] [Google Scholar]
  • 108.Zhao K, Wang Y, Han L, Wang Y, Luo X, et al. Nanogenerator-based self-charging energy storage devices. Nano-Micro Lett. 2019;11:19. doi: 10.1007/s40820-019-0251-7. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 109.Soares dos Santos MP, Coutinho J, Marote A, Sousa B, Ramos A, et al. Capacitive technologies for highly controlled and personalized electrical stimulation by implantable biomedical systems. Sci. Rep. 2019;9:5001. doi: 10.1038/s41598-019-41540-3. [DOI] [PMC free article] [PubMed] [Google Scholar]
  • 110.Valentini L, Rescignano N, Puglia D, Cardinali M, Kenny J. Preparation of alginate/graphene oxide hybrid films and their integration in triboelectric generators. Eur. J. Inorg. Chem. 2015;2015(7):1192–1197. doi: 10.1002/ejic.201402610. [DOI] [Google Scholar]
  • 111.Wu C, Kim TW, Choi HY. Reduced graphene-oxide acting as electron-trapping sites in the friction layer for giant triboelectric enhancement. Nano Energy. 2017;32:542–550. doi: 10.1016/j.nanoen.2016.12.035. [DOI] [Google Scholar]

Articles from Nano-Micro Letters are provided here courtesy of Springer

RESOURCES