Skip to main content
NIHPA Author Manuscripts logoLink to NIHPA Author Manuscripts
. Author manuscript; available in PMC: 2022 Dec 9.
Published in final edited form as: Aerosol Sci Technol. 2019 Aug 5;53(10):1197–1203. doi: 10.1080/02786826.2019.1645294

Toxic emissions resulting from sucralose added to electronic cigarette liquids

Rachel El-Hage †,§, Ahmad El-Hellani †,§, Christina Haddad †,§, Rola Salman ‡,§, Soha Talih ‡,§, Alan Shihadeh ‡,§, Thomas Eissenberg ˧,§, Najat Aoun Saliba †,§,*
PMCID: PMC9733909  NIHMSID: NIHMS1820786  PMID: 36506805

Abstract

Electronic cigarettes (ECIGs) are appealing in part because of the many flavors of the liquids used in them. Concerns have been raised that some ECIG liquid flavors, especially those that are sweet, are attracting otherwise nicotine-naïve youth to ECIGs. Sucralose is an artificial, non-caloric sweetener that is added to some ECIG liquids. In this study, we evaluated the toxicants, namely isomers of chloropropanols that can be produced when sucralose-containing ECIG liquid is aerosolized. An analytical separation method relying on solid-phase extraction (SPE) to isolate chloropropanols from the propylene glycol/glycerol matrix was developed. Chloropropanols were then derivatized by silylation before they were analyzed on GC-MS. The influence of different ECIG operating conditions on the generation of chloropropanols was studied by varying ECIG device design and power output and also the sucralose concentration of the liquid. Heated sucralose-containing ECIG liquids produce two toxic compounds that can be found in the resulting aerosols. The two chloropropanols, 3-monochloro-1,2-propanediol (3-MCPD) and 1,3-dichloropropanol (1,3-DCP) that were detected under all conditions were found to be correlated significantly with liquid sucralose content. Effective regulation of ECIGs will minimize user and bystander exposure to these and other ECIG toxicants.

Keywords: Electronic cigarette, sucralose, chloropropanol, thermal degradation

Graphical Abstract

graphic file with name nihms-1820786-f0005.jpg

Introduction

The prevalence of electronic cigarette (ECIG) use has increased tremendously since their introduction to the market (McMillen et al. 2015, Anic et al. 2018). This increased use is usually attributed to several factors including the perception of reduced risk relative to combustible cigarettes and high appeal to former and current smokers as well as to nicotine-naïve users (Majeed et al. 2017, Bao et al. 2018, Fulton et al. 2018). ECIGs are advertised as safer alternatives to combustible cigarettes because they contain a simpler matrix of chemicals (polyol solvents with or without nicotine and flavorings) subjected to lower temperatures during aerosolization (Breland et al. 2017). Moreover, there are claims that these chemicals distill almost intact to the generated aerosols that will be inhaled by the user (Margham et al. 2016). However, these claims were shown to be false with the detection of toxicants like aldehydes, reactive oxygen species, and metals at levels sometimes comparable or greater than those of combustible tobacco products (Jensen et al. 2015, Ogunwale et al. 2017, Wang et al. 2017, Haddad et al. 2018, Salamanca et al. 2018). ECIG appeal is increased by the plethora of flavorings in ECIG liquids – traditional flavors such as “tobacco” and “menthol” are available, as are non-traditional flavors that are intended to resemble fruit, desserts, candy, and other sweet foods (St.Helen et al. 2018, Bono et al. 2019). Recently, several studies have reported that flavor additives increase the toxicant profile of ECIG aerosol (Khlystov and Samburova 2016, Bitzer et al. 2018), with one report showing higher toxicity from adducts formed between flavor chemicals and propylene glycol (PG), a common ECIG base liquid (Erythropel et al. 2018).

In 2009, the US FDA banned the addition of characterizing flavors, other than menthol, to tobacco cigarettes. However, characterizing flavors are not banned in the US for other tobacco or nicotine delivery products, including waterpipe tobacco (shisha), smokeless tobacco products, and ECIGs (FDA 2018a). In the case of ECIGs, sweet flavors were found to increase product appeal among youth (Kroemer et al. 2018), increasing the risk of nicotine dependence among youth and probably acting as a gateway to smoking (Spindle et al. 2017, Morgenstern et al. 2018, NIDA 2018). A sweet flavor in ECIG liquid can be obtained by the addition of saccharides (sucrose or honey monosaccharides) or artificial non-caloric sweeteners/sweet enhancers (such as ethyl maltol, sucralose or sorbitol) (Miao et al. 2016, Fagan et al. 2018). Sucralose is a high intensity sweetener (up to 600 times sweeter than sucrose) that is marketed as an additive for Do-It-Yourself (DIY) mixing of ECIG liquids (Rosbrook et al. 2017, Amazon 2018). FDA approves it as a general sweetener for food, but it is not currently listed as “generally recognized as safe” (FDA 2018b).

The safety and toxicity of sucralose have become controversial (Abou-Donia et al. 2008, Brusick et al. 2009, Grotz and Munro 2009, Berry et al. 2016). Although originally thought to be thermally stable, several studies reported the degradation of sucralose at temperatures that are expected during cooking (Hutchinson et al. 1999, Dong et al. 2011, Dong et al. 2013). The effect of temperature on sucralose was studied by thermogravimetric analysis/differential scanning calorimetry techniques and showed that degradation of sucralose starts at temperatures as low as 120 °C yielding hydrochloric acid (HCl) (Bannach et al. 2009, de Oliveira et al. 2015). Furthermore, it has been shown that heating sucralose in the presence of glycerol in some food products leads to the formation of chloropropanols that have considerable toxicity (Rahn and Yaylayan 2010, Schiffman and Rother 2013). Chloropropanol formation in foods raises a concern about the use of sucralose as an additive in ECIG liquids. In this study, we assessed the generation of chloropropanols upon aerosolizing a sucralose-containing liquid in two ECIG devices at different powers. To enable quantification of chloropropanols in ECIG aerosols, an analytical separation method was developed and optimized to isolate chloropropanols from propylene glycol (PG) and vegetable glycerin (VG), the primary ECIG aerosol constituents. Following isolation, chloropropanols were derivatized by silylation and then analyzed using Gas Chromatography coupled to a Mass Spectroscopy GC-MS (González et al. 2011, Kim et al. 2015, Yang et al. 2018).

Materials and methods

Materials

PG (99.5%) (CAS No 57–55-6), VG (99%–101%) (CAS No 56–81-5), 1,3-dichloro-2-propanol (1,3-DCP) (CAS No 96–23-1), (±)-3-Chloro-1,2-propanediol (3-MCPD) (CAS No 96–24-2), 2-bromoethanol (2-BE) (CAS No 540–51-2) and sucralose (CAS No 56038–13-2) were procured from Sigma-Aldrich. N,O-Bis(trimethylsilyl)trifluoroacetamide (BSTFA) with 1% trimethylchlorosilane (25561–30-2) used for the derivatization of chloropropanols before GC analysis was purchased from Fluka. HPLC grade solvents including ethyl acetate and methanol were purchased from Sigma-Aldrich. Quartz filters (ADVENTEC, QR-100 47 mm) were procured from Pall Corporation. TELOS neo PRP 200mg/6ml solid phase extraction (SPE) cartridges were purchased from TELOS. ECIG devices, including above-Ohm Vaporfi platinum II (2.2 Ω coil) and sub-Ohm Smok TFV12 (0.15 Ω coil) were purchased from online vendors.

Methods

Study design

Our approach was to evaluate the influence of electric power and sucralose content on chloropropanol yields in smoking machine generated-aerosols emitted by an above-Ohm and sub-Ohm ECIG device. Two different loadings of sucralose (1 and 5 %) in ECIG liquid were prepared by dissolving pure sucralose powder in standard PG, VG and deionized water mixture (ratio: 28:67:5, respectively). These sucralose loadings were chosen based on previously reported work investigating the influence of sucralose on the sweetness of commercial flavors (Rosbrook, Erythropel et al. 2017). Different powers were tested for each ECIG design: 100, 150 and 200 W for sub-Ohm and 5 and 11 W for above-Ohm ECIGs. These powers were consistent with the manufacturer’s recommendations for these devices. The formation of various mono- and di-chloropropanols is possible from PG and VG yielding two (1-chloro-2-propanol and 2-chloro-1-propanol) and four chloropropanols (3-chloro-1,2-propanediol (3-MCPD), 2-chloro-1,3-propanediol, 1,3-dichloro-2-propanol (1,3-DCP), and 2,3-dichloro-1-propanol), respectively. In this study, the method was optimized to detect the most toxic compounds, namely 3-MCPD and 1,3-DCP (IARC classification, group 2B).

Aerosol generation and sampling

The AUB Aerosol Lab Vaping Instrument (ALVIN) was used to generate ECIG aerosols (Talih et al. 2015), using a puffing regimen consisting of 15 puffs for above-Ohm and three puffs for the sub-Ohm device, 4-sec puff duration, 10-sec inter-puff interval, and 1 L/min flow rate. The generated aerosols were trapped on 47 mm quartz filters, using the same setup previously described in Talih et al. (2015).

Separation method

A clean-up analytical method using solid phase extraction (SPE) cartridges was developed and optimized (Figure 1).

Figure 1.

Figure 1.

A stepwise scheme of the optimized analytical method for the separation of chloropropanols.

As shown in Figure 1, aerosols trapped on the quartz filters were extracted in 10 mL NaCl aqueous solution (15 % w/w) and then loaded onto an SPE cartridge. The SPE was pre-conditioned with ethyl acetate, methanol, and water (4 mL each). After loading the sample, the SPE was washed with 1.5 mL of water and then air-dried for 10 min to remove any remaining water on the stationary phase. The analytes were then eluted with 6 mL of ethyl acetate using a vacuum manifold at a rate of 1 drop/sec. The organic layer was concentrated under nitrogen flow (10 L/min) down to 100 μL and spiked with Bromoethanol as an internal standard for quantification. The mixture was reacted with N, O-Bistrifluoroacetamide (BSTFA) (50 μL) for derivatization of the hydroxyl groups while heating at 70 °C for 30 min. An aliquot was injected into GC-MS for analysis. Table 1 summarizes the analytical parameters of the optimized method.

Table 1.

Method validation parameters.

1,3-DCP 3-MCPD

Recovery (%) 80–110 60–90
LOD (μg/mL) 0.07 0.03
LOQ (μg/mL) 0.09 0.05
Range of calibration curve 0.09–4.4 0.05–4.4
Repeatability (%RSD) 5–12 7–20

GC-MS method

The GC-MS analysis was performed on a Thermo Trace GC-2000 POLARIS QMS instrument equipped with a thermostatically controlled AI 3000 auto-sampler and a TG-5MS Thermo Scientific fused silica capillary GC column (30 m × 0.25 mm × 0.25 μm). The mobile phase was helium delivered at 1 mL/min flow rate. The injector temperature was 250 °C, with a split-less injection mode of 1μL. The oven temperature program was: 50 °C for 1 min, 5 °C/min ramp to 90 °C, and another ramp of 10 °C/min to 240 °C. The total run time was 25 min, and the solvent delay time was 6.6 min. The quantification was performed using selected ion mass (SIM) mode with two qualifiers and one quantifier peak for each analyte, as shown in Table 2.

Table 2.

Qualifiers and quantifier peaks in GC-MS (m/z) of the selected analytes.

Analyte Qualifier 1 Qualifier 2 Quantifier

1,3-DCP 151 185 93
3-MCPD 101 116 239
2-BE 137 183 139

1,3-DCP: 1,3-dichloro-2-propanol; 3-MCPD: 3-Chloro-1,2-propanediol; 2-bromoethanol

Results and Discussion

The optimized separation method allowed the isolation of chloropropanols from PG and VG matrix due to the salting-out effect of NaCl that retained the chloropropanols on the stationary phase of the SPE. Both chloropropanols, 3-MCPD and 1,3-DCP, were identified only in aerosols and not in the gas phase (Figures S3S5) in all conditions at levels ranging from zero to 25 μg/puff. Chloropropanol yields were strongly dependent on sucralose concentration (p < 0.05) and were found to be unrelated to the power level (p < 0.899 and 0.528 for 3-MCPD and 1,3-DCP, respectively). Sub-ohm and above-Ohm devices had similar levels of 3-MCPD, while sub-Ohm devices exhibited greater levels of DCP, although not significant (p < 0.147). Results are illustrated in Figure 2.

Figure 2.

Figure 2.

A bar graph of 3-MCPD (A) and 1,3-DCP (B) concentration versus the different ECIG operating parameters. %Su, P(W), and ECIG refer to sucralose content (%), power output (W) and ECIG design, respectively.

The chloropropanols are produced from the halogenation reaction of polyols like PG and VG with HCl. This latter is generated from sucralose degradation upon heating (R1 and R2). Thermo-gravimetric analysis (TGA) of sucralose confirmed, as reported in the literature, that the emission of HCl initiates at 130 °C (Supplementary information (Figure S1)) and that aerosolizing ECIG liquid containing sucralose dissolved in PG leads to the formation of gaseous acid-catalyzed products as depicted by infrared (IR) and nuclear magnetic resonance (NMR) spectroscopy analysis (Figures S3S5). Products found in the gas phase like acetals were detected only in the absence of nicotine in the ECIG liquid. Acetal is known to be an acid transformation catalyzed in this case by HCl that is produced from the sucralose degradation reaction. In the presence of nicotine, an HCl-nicotine scavenging reaction is most likely to take place, eliminating, thereby the formation of the acetal.

graphic file with name nihms-1820786-f0003.jpg R1
graphic file with name nihms-1820786-f0004.jpg R2

The influence of different ECIG operating parameters including device type, power and sucralose liquid content on the generation of 3-MCPD and 1,3-DCP is summarized in Figure 2. 3-MCPD and 1,3-DCP result from the reactions of HCl with VG and 3-MCPD, respectively. 1,3-DCP concentration seems to be limited by the formation of 3-MCPD, and as such, it is observed at much lower concentrations. Both 3-MCPD and 1,3-DCP exhibit carcinogenic and genotoxic properties in animals (Eder and Weinfurtner 1994, Cho et al. 2008, Baer et al. 2010). Also, 3-MCPD has been reported to have male antifertility effects and is commonly used as a rat chemosterilant (Kwack et al. 2004). They are classified as possibly carcinogenic to humans (group 2B) by the International Agency for Research on Cancer (IARC) (IARC 2013a, IARC 2013b). As per IARC classification, the toxicity of these compounds is similar to acetaldehyde reported as the most harmful carbonyl in ECIGs after formaldehyde (Bekki et al. 2014).

Table 3 summarizes the multiple variable analysis of the correlation between the formation of 3-MCPD and 1,3-DCP and the different ECIG operating conditions. Only sucralose concentration in the ECIG liquid significantly affected the emission of chloropropanols (p < 0.05). The fact that power has no significant effect on the generation of chloropropanols (P value is 0.528 for 1,3-DCP and 0.899 for 3-MCPD) could be explained by the low stability of sucralose, degrading at relatively low temperatures that can be attained by all the tested powers.

Table 3.

Statistical Analysis (p value) of the effect of different ECIG operating parameters on chloropropanols formation

1,3-DCP (ug/puff) 3-MCPD (ug/puff)

Device 0.720 0.147
Concentration 0.000 * 0.000 *
Power 0.528 0.899
*

: statistically significant (P < 0.05)

Our results show that the addition of sucralose as a sweetener in ECIG liquid yields chloropropanols that are classified as possibly carcinogenic to humans (Group 2B). There is limited information about the toxicity of chloropropanols (Andres et al. 2013). The only toxicity level reported for chloropropanols is a provisional maximum tolerable daily intake (PMTDI) of 2μg/kg of body weight estimated from a long-term study of toxicity and carcinogenicity in rats (FSANZ 2003). If we consider a rough estimation of ECIG use at 150 puffs/day, a 70 kg user will be exposed to 0–18 times more than PMTDI depending on the operating conditions, keeping in mind the difference between inhalation and ingestion routes. The detection of these possible carcinogens in the aerosols of sweet flavored liquids adds to the risk of carcinogenic carbonyls emitted from the degradation of the base liquid. Therefore, policymakers worldwide should consider banning the use of sucralose as an additive in ECIG liquids.

Supplementary Material

Supplementary Informaiton

Acknowledgment

This work was supported by the National Institute on Drug Abuse (U54DA036105) and the Center for Tobacco Products of the US Food and Drug Administration. This content is solely the responsibility of the authors and does not necessarily represent the official views of the National Institutes of Health or the Food and Drug Administration.

Footnotes

Declaration of Interest

Drs. Eissenberg and Shihadeh are paid consultants in litigation against the tobacco industry and are named on a patent for a device that measures the puffing behavior of electronic cigarette users. All other authors have no potential conflict of interest to be disclosed.

Supporting Information

Supporting information includes TGA, FTIR, and NMR spectra of the gas phase emissions from a sucralose-containing ECIG liquid.

References

  1. Abou-Donia MB, El-Masry EM, Abdel-Rahman AA, McLendon RE and Schiffman SS 2008. Splenda Alters Gut Microflora and Increases Intestinal P-Glycoprotein and Cytochrome P-450 in Male Rats. Journal of Toxicology and Environmental Health, Part A 71(21): 1415–29. [DOI] [PubMed] [Google Scholar]
  2. Amazon. 2018. NuSweet Liquid Sucralose, Concentrated Liquid Sweetener, 4 Oz. Accessed November 6, 2018. https://www.amazon.com/NuSweet-Liquid-Sucralose-Concentrated-Sweetener/dp/B00I28OQ7K.
  3. Andres S, Appel KE and Lampen A 2013. Toxicology, occurrence and risk characterisation of the chloropropanols in food: 2-Monochloro-1,3-propanediol, 1,3-dichloro-2-propanol and 2,3-dichloro-1-propanol. Food and Chemical Toxicology 58: 467–78. [DOI] [PubMed] [Google Scholar]
  4. Anic GM, Holder-Hayes E, Ambrose BK, Rostron BL, Coleman B, Jamal A and Apelberg BJ 2018. E-cigarette and Smokeless Tobacco Use and Switching Among Smokers: Findings From the National Adult Tobacco Survey. American Journal of Preventive Medicine 54(4): 539–51. [DOI] [PubMed] [Google Scholar]
  5. Baer I, de la Calle B and Taylor P 2010. 3-MCPD in food other than soy sauce or hydrolysed vegetable protein (HVP). Analytical and Bioanalytical Chemistry 396(1): 443–56. [DOI] [PubMed] [Google Scholar]
  6. Bannach G, Almeida RR, Lacerda LG, Schnitzler E and Ionashiro M 2009. Thermal stability and thermal decomposition of sucralose. Eclética Química São Paulo 34(4): 21–26. [Google Scholar]
  7. Bao W, Xu G, Lu J, Snetselaar LG and Wallace RB 2018. Changes in electronic cigarette use among adults in the united states, 2014–2016. Journal of the American Medical Association 319(19): 2039–41. [DOI] [PMC free article] [PubMed] [Google Scholar]
  8. Bekki K, Uchiyama S, Ohta K, Inaba Y, Nakagome H and Kunugita N 2014. Carbonyl compounds generated from electronic cigarettes. International journal of environmental research and public health 11(11): 11192–200. [DOI] [PMC free article] [PubMed] [Google Scholar]
  9. Berry C, Brusick D, Cohen SM, Hardisty JF, Grotz VL and Williams GM 2016. Sucralose Non-Carcinogenicity: A Review of the Scientific and Regulatory Rationale. Nutrition and cancer 68(8): 1247–61. [DOI] [PMC free article] [PubMed] [Google Scholar]
  10. Bitzer ZT, Goel R, Reilly SM, Elias RJ, Silakov A, Foulds J, Muscat J and Richie JP 2018. Effect of flavoring chemicals on free radical formation in electronic cigarette aerosols. Free Radical Biology and Medicine 120: 72–79. [DOI] [PMC free article] [PubMed] [Google Scholar]
  11. Bono RS, Barnes AJ, Lester RC and Cobb CO 2019. Effects of Electronic Cigarette Liquid Flavors and Modified Risk Messages on Perceptions and Subjective Effects of E-Cigarettes. Health Education & Behavior 46(2): 197–203. [DOI] [PMC free article] [PubMed] [Google Scholar]
  12. Breland A, Soule E, Lopez A, Ramôa C, El-Hellani A and Eissenberg T 2017. Electronic cigarettes: what are they and what do they do? Annals of the New York Academy of Sciences 1394(1): 5–30. [DOI] [PMC free article] [PubMed] [Google Scholar]
  13. Brusick D, Borzelleca JF, Gallo M, Williams G, Kille J, Wallace Hayes A, Xavier Pi-Sunyer F, Williams C and Burks W 2009. Expert Panel report on a study of Splenda in male rats. Regulatory Toxicology and Pharmacology 55(1): 6–12. [DOI] [PubMed] [Google Scholar]
  14. Cho W-S, Han BS, Nam KT, Park K, Choi M, Kim SH, Jeong J and Jang DD 2008. Carcinogenicity study of 3-monochloropropane-1,2-diol in Sprague–Dawley rats. Food and Chemical Toxicology 46(9): 3172–77. [DOI] [PubMed] [Google Scholar]
  15. de Oliveira DN, de Menezes M and Catharino RR 2015. Thermal degradation of sucralose: a combination of analytical methods to determine stability and chlorinated byproducts. Scientific Reports 5: 9598. [DOI] [PMC free article] [PubMed] [Google Scholar]
  16. Dong S, Liu G, Zhang B, Gao L and Zheng M 2013. Formation of polychlorinated naphthalenes during the heating of cooking oil in the presence of high amounts of sucralose. Food Control 32(1): 1–5. [Google Scholar]
  17. Dong S, Wu J, Liu G, Zhang B and Zheng M 2011. Unintentionally produced dioxin-like polychlorinated biphenyls during cooking. Food Control 22(11): 1797–802. [Google Scholar]
  18. Eder E and Weinfurtner E 1994. Mutagenic and carcinogenic risk of oxygen containing chlorinated C-3 hydrocarbons: Putative secondary products of C-3 chlorohydrocarbons and chlorination of water. Chemosphere 29(9): 2455–66. [DOI] [PubMed] [Google Scholar]
  19. Erythropel HC, Jabba SV, DeWinter TM, Mendizabal M, Anastas PT, Jordt SE and Zimmerman JB 2018. Formation of flavorant–propylene Glycol Adducts With Novel Toxicological Properties in Chemically Unstable E-Cigarette Liquids. Nicotine & Tobacco Research: nty192–nty92. [DOI] [PMC free article] [PubMed] [Google Scholar]
  20. Fagan P, Pokhrel P, Herzog TA, Moolchan ET, Cassel KD, Franke AA, Li X, Pagano I, Trinidad DR, Sakuma K.-l. K., Sterling K, Jorgensen D, Lynch T, Kawamoto C, Guy MC, Lagua I, Hanes S, Alexander LA, Clanton MS, Graham-Tutt C, Eissenberg T and Addictive Carcinogens W 2018. Sugar and Aldehyde Content in Flavored Electronic Cigarette Liquids. Nicotine & Tobacco Research 20(8): 985–92. [DOI] [PMC free article] [PubMed] [Google Scholar]
  21. FDA. 2018a. Menthol and Other Flavors in Tobacco Products. Accessed November 5, 2018. https://www.fda.gov/tobaccoproducts/labeling/productsingredientscomponents/ucm2019416.htm#reference.
  22. FDA. 2018b. Additional Information about High-Intensity Sweeteners Permitted for Use in Food in the United States. Accessed November 6, 2018. https://www.fda.gov/food/food-additives-petitions/additional-information-about-high-intensity-sweeteners-permitted-use-food-united-states.
  23. FSANZ. 2003. Food standards Australia New Zealand technical report: Chloropropanols in food: An analysis of the public health risk. Accessed November 8, 2018. https://www.foodstandards.gov.au/publications/Documents/Chloropropanol%20Report%20(no%20appendices)%20-%2011%20Sep%2003b-2.pdf.
  24. Fulton E, Gokal K, Griffiths S and Wild S 2018. More than half of adolescent E-Cigarette users had never smoked a cigarette: findings from a study of school children in the UK. Public Health 161: 33–35. [DOI] [PubMed] [Google Scholar]
  25. González P, Racamonde I, Carro AM and Lorenzo RA 2011. Combined solid-phase extraction and gas chromatography–mass spectrometry used for determination of chloropropanols in water. Journal of Separation Science 34(19): 2697–704. [DOI] [PubMed] [Google Scholar]
  26. Grotz VL and Munro IC 2009. An overview of the safety of sucralose. Regulatory Toxicology and Pharmacology 55(1): 1–5. [DOI] [PubMed] [Google Scholar]
  27. Haddad C, Salman R, El-Hellani A, Talih S, Shihadeh A and Saliba NA 2018. Reactive Oxygen Species Emissions from Supra- and Sub-Ohm Electronic Cigarettes. Journal of Analytical Toxicology 43(1): 45–50. [DOI] [PMC free article] [PubMed] [Google Scholar]
  28. Hutchinson SA, Ho GS and Ho CT 1999. Stability and degradation of the high-intensity sweeteners: Aspartame, Alitame, and Sucralose. Food Reviews International 15(2): 249–61. [Google Scholar]
  29. IARC. 2013a. 1,3-dichloro-2-propanol. Accessed February 7, 2019. https://monographs.iarc.fr/wp-content/uploads/2018/06/mono101-011.pdf.
  30. IARC. 2013b. 3-monochloro-1,2-propanediol. Accessed February 7, 2019. https://monographs.iarc.fr/wp-content/uploads/2018/06/mono101-010.pdf.
  31. Jensen RP, Luo W, Pankow JF, Strongin RM and Peyton DH 2015. Hidden Formaldehyde in E-Cigarette Aerosols. New England Journal of Medicine 372(4): 392–94. [DOI] [PubMed] [Google Scholar]
  32. Khlystov A and Samburova V 2016. Flavoring Compounds Dominate Toxic Aldehyde Production during E-Cigarette Vaping. Environmental Science & Technology 50(23): 13080–85. [DOI] [PubMed] [Google Scholar]
  33. Kim W, Jeong YA, On J, Choi A, Lee J-Y, Lee JG, Lee K-G and Pyo H 2015. Analysis of 3-MCPD and 1,3-DCP in Various Foodstuffs Using GC-MS. Toxicological research 31(3): 313–19. [DOI] [PMC free article] [PubMed] [Google Scholar]
  34. Kroemer NB, Veldhuizen MG, Delvy R, Patel BP, O’Malley SS and Small DM 2018. Sweet taste potentiates the reinforcing effects of e-cigarettes. European Neuropsychopharmacology 28(10): 1089–102. [DOI] [PubMed] [Google Scholar]
  35. Kwack SJ, Kim SS, Choi YW, Rhee GS, Lee RD, Seok JH, Chae SY, Won YH, Lim KJ, Choi KS, Park KL and Lee BM 2004. Mechanism of antifertility in male rats treated with 3-monochloro-1,2-propanediol (3-MCPD). Journal of Toxicology and Environmental Health, Part A 67(23–24): 2001–04. [DOI] [PubMed] [Google Scholar]
  36. Majeed BA, Weaver SR, Gregory KR, Whitney CF, Slovic P, Pechacek TF and Eriksen MP 2017. Changing Perceptions of Harm of E-Cigarettes Among U.S. Adults, 2012–2015. American Journal of Preventive Medicine 52(3): 331–38. [DOI] [PMC free article] [PubMed] [Google Scholar]
  37. Margham J, McAdam K, Forster M, Liu C, Wright C, Mariner D and Proctor C 2016. Chemical Composition of Aerosol from an E-Cigarette: A Quantitative Comparison with Cigarette Smoke. Chemical Research in Toxicology 29(10): 1662–78. [DOI] [PubMed] [Google Scholar]
  38. McMillen RC, Gottlieb MA, Shaefer RMW, Winickoff JP and Klein JD 2015. Trends in Electronic Cigarette Use Among U.S. Adults: Use is Increasing in Both Smokers and Nonsmokers. Nicotine & Tobacco Research 17(10): 1195–202. [DOI] [PubMed] [Google Scholar]
  39. Miao S, Beach ES, Sommer TJ, Zimmerman JB and Jordt S-E 2016. High-Intensity Sweeteners in Alternative Tobacco Products. Nicotine & Tobacco Research 18(11): 2169–73. [DOI] [PMC free article] [PubMed] [Google Scholar]
  40. Morgenstern M, Nies A, Goecke M and Hanewinkel R 2018. E-Cigarettes and the Use of Conventional Cigarettes. deutsches ärzteblatt international 115(14): 243–8. [DOI] [PMC free article] [PubMed] [Google Scholar]
  41. NIDA. 2018. Electronic Cigarettes (E-cigarettes). Accessed November 5, 2018. https://www.drugabuse.gov/publications/drugfacts/electronic-cigarettes-e-cigarettes.
  42. Ogunwale MA, Li M, Ramakrishnam Raju MV, Chen Y, Nantz MH, Conklin DJ and Fu X-A 2017. Aldehyde Detection in Electronic Cigarette Aerosols. ACS omega 2(3): 1207–14. [DOI] [PMC free article] [PubMed] [Google Scholar]
  43. Rahn A and Yaylayan V 2010. Thermal degradation of sucralose and its potential in generating chloropropanols in the presence of glycerol. Food chemistry 118(1): 56–61. [Google Scholar]
  44. Rosbrook K, Erythropel HC, DeWinter TM, Falinski M, O’Malley S, Krishnan-Sarin S, Anastas PT, Zimmerman JB and Green BG 2017. The effect of sucralose on flavor sweetness in electronic cigarettes varies between delivery devices. PLOS ONE 12(10): e0185334. [DOI] [PMC free article] [PubMed] [Google Scholar]
  45. Salamanca JC, Meehan-Atrash J, Vreeke S, Escobedo JO, Peyton DH and Strongin RM 2018. E-cigarettes can emit formaldehyde at high levels under conditions that have been reported to be non-averse to users. Scientific Reports 8(1): 7559. [DOI] [PMC free article] [PubMed] [Google Scholar]
  46. Schiffman SS and Rother KI 2013. Sucralose, A Synthetic Organochlorine Sweetener: Overview Of Biological Issues. Journal of Toxicology and Environmental Health, Part B 16(7): 399–451. [DOI] [PMC free article] [PubMed] [Google Scholar]
  47. Spindle TR, Hiler MM, Cooke ME, Eissenberg T, Kendler KS and Dick DM 2017. Electronic cigarette use and uptake of cigarette smoking: A longitudinal examination of U.S. college students. Addictive Behaviors 67: 66–72. [DOI] [PMC free article] [PubMed] [Google Scholar]
  48. St.Helen G, Shahid M, Chu S and Benowitz NL 2018. Impact of e-liquid flavors on e-cigarette vaping behavior. Drug and Alcohol Dependence 189: 42–48. [DOI] [PMC free article] [PubMed] [Google Scholar]
  49. Talih S, Balhas Z, Eissenberg T, Salman R, Karaoghlanian N, El Hellani A, Baalbaki R, Saliba N and Shihadeh A 2015. Effects of user puff topography, device voltage, and liquid nicotine concentration on electronic cigarette nicotine yield: measurements and model predictions. Nicotine & Tobacco Research 17(2): 150–57. [DOI] [PMC free article] [PubMed] [Google Scholar]
  50. Wang P, Chen W, Liao J, Matsuo T, Ito K, Fowles J, Shusterman D, Mendell M and Kumagai K 2017. A Device-Independent Evaluation of Carbonyl Emissions from Heated Electronic Cigarette Solvents. PLOS ONE 12(1): e0169811. [DOI] [PMC free article] [PubMed] [Google Scholar]
  51. Yang S, Kwon K, Choi J and Jo C-H 2018. Improvement of a GC–MS analytical method for the simultaneous detection of 3-MCPD and 1,3-DCP in food. Food Science and Biotechnology 27(3): 859–66. [DOI] [PMC free article] [PubMed] [Google Scholar]

Associated Data

This section collects any data citations, data availability statements, or supplementary materials included in this article.

Supplementary Materials

Supplementary Informaiton

RESOURCES