Skip to main content
NCBI home page
ACS Omega logoLink to ACS Omega
. 2019 Aug 5;4(8):13303–13308. doi: 10.1021/acsomega.9b01479

High Aspect Ratio and Post-Processing Free Silver Nanowires as Top Electrodes for Inverted-Structured Photodiodes

Min Jia Saw †, Batu Ghosh ‡, Mai Thanh Nguyen †, Kridsada Jirasattayaporn †,§, Soorathep Kheawhom §, Naoto Shirahata ‡,∥,⊥,*, Tetsu Yonezawa †,*
PMCID: PMC6705234  PMID: 31460458

Abstract

graphic file with name ao9b01479_0006.jpg

Silver nanowires (Ag NWs) as transparent conducting electrodes are widely used in many applications such as organic light-emitting diodes (OLEDs), polymer light-emitting diodes, touch screens, solar cells, and transparent heaters. In this work, using a large-scale synthesis, the synthesized Ag NWs had a high aspect ratio of 2820. The Ag NWs could be applied as a top transparent electrode in a device by simple drop-casting without any post-processing steps. The fabricated device comprised 4,4′-bis(carbazol-9-yl)biphenyl/MoO3 organic/inorganic layers which are parts of the inverted structure OLEDs or solar cells. The photodiode characteristics at the UV range were observed in the device. The ability of Ag NWs to replace opaque metals as top electrodes in a device has been demonstrated.

1. Introduction

Nanoparticles and nanowires (NWs) are highly attractive materials in the field of electronic devices as well as other fields.1−15 In a typical optoelectronic device structure, the bottom electrode is often a transparent conducting electrode, while the top electrode is normally a metal thin film.16−24 The device performance is hence limited as light is not transmitted through the top electrode which is opaque. The device performances can be enhanced by using a transparent metal conducting material as the top electrode. Among transparent metal conducting materials available, silver NWs (Ag NWs) are widely used as transparent conducting bottom electrodes because of their highest electrical conductivity and ease in synthesizing1,25−34 Ag NWs have been reported to be used in many applications such as organic light-emitting diodes (OLEDs), polymer LEDs, touch screens, solar cells, and transparent heaters.18−26,34 This is because Ag NW electrodes are exceptional in terms of transparency, conductivity, and flexibility and suitable to be applied in optoelectronic devices.23,25,26,28,29 Besides that, the processing of Ag NW electrodes is cost-effective because Ag NWs can be processed in solution.22,27,32,33,35

Several studies have reported the application of Ag NWs as top electrodes but their Ag NWs mostly consist of a polyvinylpyrrolidone (PVP) layer.35−40 Typically, post-processing procedures such as high temperature annealing, chemical annealing, light annealing, and tedious purification processes are required to remove the PVP layer in order to improve the conductivity and connectivity of the Ag NW network.41,42 The Ag NWs without PVP as capping agent are thus attractive as the complicated post-processing can be eliminated. Generally, when Ag NWs are applied as top electrodes, the choice of the post-processing process is often limited to annealing by heat treatment. Hence, the application of Ag NWs without the need of post-processing is desirable especially for the devices that contain heat-sensitive layers, where the post-processing temperature is critical.

The present work aims to explore the applicability of high aspect ratio and post-processing free Ag NWs as top electrodes for device application. We first synthesized Ag NWs with a high aspect ratio of 2820. The synthesized Ag NWs are then applied as a top electrode in an inverted structure photodiode by simple drop-casting at room temperature without the need for annealing after deposition. In this work, the organic/inorganic photodiode with 4,4′-bis(carbazol-9-yl)biphenyl (CBP)/MoO3 layers is fabricated. This is because CBP/MoO3 is widely used as hole-injection and hole-transport layers in inverted structure LEDs or solar cells.16,17 After the fabrication of the CBP/MoO3 photodiode with Ag NWs as the top electrode, the device performances are analyzed to investigate the potential of Ag NWs as top electrodes for inverted structure optoelectronic devices. The capability of Ag NWs as a transparent conducting top electrode is important for making double-sided, transparent flexible devices.

2. Results and Discussion

2.1. Crystal Structure and Morphology of Synthesized Ag NWs

Ag NWs were synthesized at various Fe3+ concentrations (Figures S1 and S2). The aspect ratios of Ag NWs synthesized with 40, 80, and 120 mM Fe3+ are 490, 1156, and 236, respectively, as summarized in Table 1. The optimal concentration of Fe3+ for obtaining the highest aspect ratio is found to be 80 mM. To investigate the feasibility of scaling up the synthesis, the synthesis was scaled-up by 10 times (namely, large scale) with using 80 mM Fe3+ as the catalyst. The synthesized Ag NWs in large-scaled synthesis has an aspect ratio of 2820. We found that in large-scale synthesis, the AgCl seeds were bigger than those in small-scale synthesis (Figure S3 and Table S1). Hence, the number of seeds becomes smaller in large-scale synthesis, causing Ag NWs to grow longer than in small-scale synthesis.

Table 1. Dimensions of Ag NWs for Different Concentration of Fe3+ and Synthesis Scale.

concentration of Fe3+ (mM) Fe3+ (μmol) scale of synthesis diameter of Ag NWs (nm) length of Ag NWs (μm) aspect ratio
40 6 ×1 58.9 ± 29.5 28.9 ± 20.3 ∼490
80 12 ×1 32.1 ± 13.0 37.2 ± 17.4 ∼1156
120 18 ×1 72.7 ± 46.8 17.5 ± 6.7 ∼236
80 120 ×10 39.8 ± 36.5 110.8 ± 40.5 ∼2820
Open in a new tab

High aspect-ratio NWs are desirable as transparent conducting electrodes since percolation of the NW network can be achieved with low density of NWs.23,26,28,29 Since the Ag NWs produced in the large scale synthesis is found to have the highest aspect ratio, and large amount of NWs can be obtained in a single synthesis, these Ag NWs were used to fabricate the top electrode for the photodiode. Figure 1a,b shows the scanning electron microscopy (SEM) and transmission electron microscopy (TEM) images of the synthesized Ag NWs after purification, respectively. The average length of Ag NWs was 110 μm and the average diameter was 40 nm. The dispersion of Ag NWs in isopropanol (IPA) with a concentration of 9.76 mg/mL is shown in Figure 1c. X-ray diffraction (XRD) data in Figure 1d show that the synthesized NWs had peaks in 2θ equal to 38.12° and 44.28°, identical with that in the reference pattern of Ag. The UV–vis spectrum (Figure 1e) of NWs dispersed in IPA shows the peaks at 384 and 353 nm, where the former corresponds to the localized surface plasmon resonance of Ag NWs in transverse mode.

Figure 1.

Figure 1

Open in a new tab

(a) SEM image, (b) TEM image of Ag NWs obtained in large scale synthesis, (c) photo of the dispersion of Ag NWs in IPA, (d) XRD pattern of Ag NWs with the reference pattern of Ag (JCPDS no. 004-0783), and (e) UV–vis spectrum of synthesized Ag NWs.

2.2. Conductivity and Transparency of the Ag NW Electrode

The Ag NW electrode was prepared by depositing Ag NWs onto a cleaned glass substrate. The Ag NW electrode has an average sheet resistance of 58 Ω/sq which is suitable to be used as a transparent conducting electrode. Figure 2 shows the transmission spectra of the fabricated Ag NW electrode and a commercial indium tin oxide (ITO) electrode. The transparency of the Ag NW electrode is around 76% at the visible light range, which is lower than that of ITO (around 83% transparency). Even though the transparency of Ag NWs is lower than that of ITO in the visible light region, the application of Ag NWs as the top electrode in our device is feasible. In UV wavelengths (320–380 nm), the Ag NW electrode has approximately 68.2% transparency, which is comparable to ITO (67.8% transparency) that is used as the bottom electrode. The transparency of the Ag NW electrode in the UV region is important because the active layers of our photodiode consist of CBP and MoO3 layers, which are responsive to UV wavelengths (Figure S4).

Figure 2.

Figure 2

Open in a new tab

UV–vis transmission spectra of the Ag NW electrode and of the ITO one. The black arrow shows the transmissions of the Ag NW electrode and ITO electrode at a wavelength of 340 nm.

2.3. Application of Ag NWs as the Top Transparent Electrode in the Inverted Structure Photodiode

Since the synthesized Ag NWs display good sheet resistance and optical transparency as the transparent conductive electrode, we hence applied the Ag NWs into a photodiode as the top electrode. The organic/inorganic photodiode in our study consists of ITO as the bottom electrode, CBP/MoO3 as the active layers and Ag NWs as the top electrode, as shown in the Figure 3a. The energy band diagram of the device using Ag NWs as the top electrode is shown in Figure 3b wherein the energy value of the MoO3 layer is the measured value for MoO3 in our previous study.17Figure 3c shows the actual device under measurement with Ag NWs as the top electrode under UV irradiation. The Ag NW top electrode has well-contacted and connected NW networks that comprise of several layers of NWs, as shown in Figure 3d.

Figure 3.

Figure 3

Open in a new tab

(a) Device structure, (b) flat band diagram of the CBP/MoO3 photodiode using Ag NWs as the top electrode with the flow directions of photogenerated electrons and holes across the device, (c) photo of the real device under UV light illumination with the inset showing the device on a paper under room light, and (d) SEM image of Ag NWs as the top electrode in the device. The work functions for ITO, CBP, MoO3, and Ag NWs in the device are obtained based on references.17,43

The measurements to obtain photodiode characteristics were carried out by connecting the crocodile clips of the electrometer Keithley 2425, to Al wires which were connected to the electrodes of the photodiode via a silver paste. A xenon light source with band-pass filters of 254 ± 5, 270 ± 5, 310 ± 5, 340 ± 5, 365 ± 5, 380 ± 5, and 410 ± 5 nm was used. Since Ag NWs provide transparency for the light source to pass through as discussed in the previous section, the measurements were obtained by illuminating the device from the Ag NW side. Figure 4a shows the responsivity of the CBP/MoO3 photodiode using Ag NWs as the top electrode. The device shows the highest responsivity at wavelengths of 340 and 365 nm and lower responsivity at wavelengths of 254, 270, 310, and 380 nm. Since the absorbance peaks of CBP and MoO3 are in the range between 340 and 370 nm (Figure S4), the peak wavelengths of the responsivity curve suggest that excitons might be formed at both CBP and MoO3 layers upon illumination. As expected, the device does not show responsivity at 410 nm, which falls within the visible light range. To examine the other properties of the device, the UV light source was fixed at 340 nm that resulted in the highest responsivity.

Figure 4.

Figure 4

Open in a new tab

(a) Responsivity versus wavelength, (b) I–V curve, (c) photocurrent vs optical power, and (d) on/off switching curves (under zero-bias conditions) of CBP/MoO3 photodiodes using Ag NWs as the top electrode and ITO as the bottom electrode.

The I–V characteristics in the UV range using Ag NWs as the top electrode are shown in Figure 4b. The dark current measured is 1 nA at biases of 0.4 and −0.4 V. The dark and the photocurrent I–V curves show symmetric and linear behaviors. At a bias of −0.4 V, the photocurrent is −1.5 nA for 1.2 mW incident power, which represents a photocurrent to dark current ratio of 1.5. The symmetry of the I–V curves might be due to the very less work-function difference between ITO (∼4.8 eV) and Ag NWs (∼4.6 eV) and the energy levels of the CBP and MoO3 layers. The dark and illuminated I–V curves for the region near 0 V demonstrate the presence of a photovoltaic effect under illumination at 340 nm light. The maximum short-circuit current is −1.5 nA for an incident power of 1.2 mW. The open-circuit voltage is 0.4 V. To prove that the effect is not due to hysteresis, voltage was scanned from both directions (forward bias to reverse bias and vice versa) and the corresponding current was measured. The direction of scan has negligible effect on the photovoltaic response. This photovoltaic response, which allows separation of an electron–hole pair at zero applied bias is the indication for a type II heterostructure between the MoO3 and CBP layers, where the built-in field in the device under zero bias is sufficient to promote charge separation.

Figure 4c shows the relationship of photocurrent with the optical power of the light source. The current is negligible under dark conditions. When the optical power increases, the light intensity increases and hence the photocurrent also increases. It is clear that the photocurrent does not increase linearly with incident power. In the low power region, the response is quite linear, suggesting that during recombination, the rates of the absorbed photon and photo-generated electron–hole pairs in reaching the electrodes are constant. Above ∼0.2 mW, the photocurrent increase is slower with increased power (increased intensity). The slower increment of photocurrent in the high intensity region may be due to the saturation of electron traps. To investigate the switching behaviors of Ag NWs as the top electrode with ITO as the bottom electrode of the photodiode, the device was illuminated from both Ag NW and ITO sides. The device shows a good on/off switching behavior as shown in Figure 4d, upon illumination from both Ag NW and ITO sides. The slight difference in the photocurrents observed for the top (Ag NW side) and bottom (ITO side) may be due to the absorbance of Ag NWs. Based on the UV–vis spectra (Figure S4), the device with ITO/CBP/MoO3/Ag NWs layers shows slightly higher absorbance at 340 nm than the device with ITO/CBP/MoO3 layers, suggesting that some UV light is absorbed by the Ag NW electrode before reaching the CBP/MoO3 layers. However, overall UV light is mainly absorbed by the CBP/MoO3 layers.

3. Experimental Section

3.1. Materials

Silver nitrate (AgNO3, Sigma-Aldrich), ethylene glycol (EG, Wako), 1,2-dodecanediol (DD, TCI), sodium chloride (NaCl, Wako), iron(III) nitrate nonahydrate [Fe(NO3)3, Wako], ammonia solution (28% NH4OH, Wako), acetic acid (AcOH, Wako), IPA (Wako), CBP (Lumtec), and molybdenum oxide (MoO3, Sigma-Aldrich) were used as received.

3.2. Synthesis of High-Aspect Ratio Ag NWs

Ag NWs were synthesized based on the modified polyol method, as shown in Figure 5, with the reference to reports by Sim et al.44,45 First, 6.30 mL of EG was added into a flask and heated at 110 °C for 1 h under magnetic stirring. Simultaneously, 80 mM Fe(NO3)3 solution and 30 mM NaCl solution were prepared. Then, AgNO3 solution was prepared in another vial by adding AgNO3 into 1.50 mL of EG. After 1 h of heating, 0.15 mL of Fe(NO3)3 solution and 0.03 mL of NaCl solution were injected into the preheated EG sequentially and heated at 110 °C for another 20 min. The magnetic stirring was then removed from the solution, followed by injection of 1.50 mL of AgNO3 solution. The reaction was maintained at 110 °C for 15 h to allow the growth of NWs. The reacted solution was subsequently quenched down to room temperature and centrifuged at 5000 rpm for 30 min with DD, NH4OH, and AcOH consecutively. The purified Ag NWs were dispersed in IPA for further characterization. The concentration of Fe3+ was varied from 40 to 120 mM to acquire the optimal concentration for obtaining NWs with the highest aspect ratio. For the large scale synthesis of Ag NWs, the concentration of AgNO3, NaCl and Fe(NO3)3 were kept the same as small scale synthesis (×1) but the volumes of the solutions were increased by 10 times. Same procedures were carried out and the detailed parameters are summarized in Table 2.

Figure 5.

Figure 5

Open in a new tab

Synthesis procedure of Ag NWs.

Table 2. Concentration and Amount of Fe(NO3)3, NaCl and AgNO3 Used in Syntheses of Ag NWs.

scale Fe(NO3)3 (mM) volume of Fe(NO3)3 (mL) NaCl (mM) volume of NaCl (mL) AgNO3 used (mg) volume of AgNO3 (mL)
1 40 0.15 30 0.03 26 1.50
1 80 0.15 30 0.03 26 1.50
1 120 0.15 30 0.03 26 1.50
10 80 1.50 30 0.30 260 15.00
Open in a new tab

3.3. Fabrication of theAg NW Electrode and CBP/MoO3 Photodiode

Ag NWs were dispersed in IPA to form 1.22 mg/mL dispersion. To fabricate the Ag NW electrode, quartz glass was used as the substrate. Before use, the glass substrate was cleaned with nonionic detergent, distilled water (resistivity = 18.2 MΩ cm–1), acetone, ethanol, and IPA sequentially under sonication. The substrate was then dried and subjected to a VUV lamp (Ushio Corp.) under a pressure of 10 Pa air for 30 min. Next, the electrode was prepared by simple drop-casting of Ag NWs onto a glass substrate and leaving it to dry for 15 min naturally. To fabricate the photodiode, the commercial ITO-coated glass substrate with a resistivity of 7–15 Ω/sq was used as the bottom electrode. First, the ITO-coated substrate was etched to a narrow strip by using hydrochloric acid and zinc dust. Then, the substrate was cleaned using the same cleaning process as for the glass substrate. A layer of 60 nm thick CBP was then deposited onto the ITO-coated substrate, followed by deposition of an inorganic layer, MoO3 with 125 nm at vacuum level 10–4 Pa by using a thermal evaporation method. Ag NWs as the top electrode were drop-casted onto the MoO3 and dried naturally.

3.4. Characterization

The crystalline and phase structures of Ag NWs were characterized using XRD (Rigaku MiniFlex II X-ray diffractometer, Cu Kα radiation, λ = 1.5418 Å, scanning speed of 2° min–1). The morphologies of the synthesized NWs were examined using SEM (JEOL-JSM-6701F and Hitachi TM3030 Plus, 15 kV) and TEM(JEOL JEM-2000FX, 200 kV). The average length of the NWs was measured based on 50 NWs and the average diameter was measured based on 30 NWs in the SEM and TEM images. The absorbance and transmission of Ag NWs, the electrode, and the photodiode were characterized by using ultraviolet–visible spectroscopy (UV–vis, Shimadzu UV Spectrophotometer UV-1800 with UV Probe software and JASCO V-650). The average sheet resistivity was obtained based on 10 measurements on the Ag NW electrode by using a four-point probe method (Loresta-GP, MCP-T610, Mitsubishi Chemical Analytech, Japan). A high-power Xenon lamp (300 W, Max-301, Asahi Spectra Co., Ltd.) with band-pass filters of 254 ± 5, 270 ± 5, 310 ± 5, 340 ± 5, 365 ± 5, 380 ± 5, and 410 ± 5 nm was used as the UV light source. The responsivity, photocurrent as function of optical power, current–voltage (I–V) and switching characteristics data of the photodiode were obtained with a Keithley 2425 electrometer connected with a computer.

4. Conclusions

The synthesis of Ag NWs with a high aspect ratio of 2820 is achievable by using 80 mM Fe3+ as a catalyst and scaling up by 10 times. The sheet resistivity and transparency of the NW network are suitable for using as a transparent conductive top electrode to replace opaque metal electrodes. The Ag NWs can be deposited by simple drop-casting into the photodiode device at room temperature and without any post processing. The ability for the synthesis of Ag NWs to be scaled up, the simplicity of deposition and the elimination of complicated post-processing are beneficial for industrial production where large-scale production and simple procedures are preferable. Our demonstration on using high-aspect ratio Ag NWs as a top electrode in an inverted ITO/CBP/MoO3/Ag NW photodiode illustrates the potential of such Ag NWs to be integrated as top electrodes in full inverted structure OLEDs or solar cells in the future.

Acknowledgments

The authors thank Dr. Y. Ishida (Hokkaido University), H. Yamada (NIMS), H. Tsukamoto and H. Shirai (Hokkaido University) for fruitful discussions. We also acknowledge Ishikawa for her support in TEM. M.J.S. thanks the MEXT Scholarship for financial support during her stay in Sapporo and the NIMS academic-collaboration project. The research was partially supported by Grant-in-Aids for Scientific Research (B) (18H01820 to T.Y.), for Challenging Research (Exploratory) (19K22094 to T.Y.), for Young Researcher B (17K14072 to M.T.N.), and for JST A-step (AS282I006e, to N.S.) and the Izumi Foundation (to N.S.).

Supporting Information Available

The Supporting Information is available free of charge on the ACS Publications website at DOI: 10.1021/acsomega.9b01479.

  • SEM images of Ag NWs synthesized with different concentrations of Fe3+, XRD data of Ag NWs synthesized with different concentrations of Fe3+ and scaling-up, XRD data and crystalline size for AgCl seeds in small and big scale syntheses at 80 mM Fe3+, UV–vis spectra of the glass substrate, CBP, MoO3, Ag NWs, ITO/CBP/MoO3 and ITO/CBP/MoO3/Ag NWs (PDF)

Author Present Address

# Department of Physics, Triveni Devi Bhalotia College, Raniganj, West Bengal 713383, India.

The authors declare no competing financial interest.

Supplementary Material

ao9b01479_si_001.pdf (969.3KB, pdf)

References

  1. Langley D.; Giusti G.; Mayousse C.; Celle C.; Bellet D.; Simonato J.-P. Flexible transparent conductive materials based on silver nanowire networks: a review. Nanotechnology 2013, 24, 452001. 10.1088/0957-4484/24/45/452001. [DOI] [PubMed] [Google Scholar]
  2. De Juan L. M. Z.; Maggay I. V. B.; Nguyen M. T.; Liu W.-R.; Yonezawa T. β-Sn Nanorods with Active (001) Tip Induced LiF-Rich SEI Layer for Stable Anode Material in Lithium Ion Battery. ACS Appl. Nano Mater. 2018, 1, 3509–3519. 10.1021/acsanm.8b00664. [DOI] [Google Scholar]
  3. Yong Y.; Nguyen M. T.; Tsukamoto H.; Matsubara M.; Liao Y.-C.; Yonezawa T. Effect of decomposition and organic residues on resistivity of copper films fabricated via low-temperature sintering of inks composed of a copper complex and copper particles. Sci. Rep. 2017, 7, 45150. 10.1038/srep45150. [DOI] [PMC free article] [PubMed] [Google Scholar]
  4. Mohanmmed M. G.; Kramer R. All-Printed Flexible and Stretchable Electronics. Adv. Mater. 2017, 29, 1604965. 10.1002/adma.201604965. [DOI] [PubMed] [Google Scholar]
  5. Shirai H.; Nguyen M. T.; Ishida Y.; Yonezawa T. A New Approach for Additive-free Room Temperature Sintering of Conductive Patterns Using Polymer-stabilized Sn Nanoparticles. J. Mater. Chem. C 2016, 4, 2228–2234. 10.1039/c6tc00161k. [DOI] [Google Scholar]
  6. Matsuhisa N.; Inoue D.; Zalar P.; Jin H.; Matsuba Y.; Itoh A.; Yokota T.; Hashizume D.; Someya T. Printable elastic conductors by in situ formation of silver nanoparticles from silver flakes. Nat. Mater. 2017, 16, 834–840. 10.1038/nmat4904. [DOI] [PubMed] [Google Scholar]
  7. Saw M. J.; Nguyen M. T.; Zhu S.; Wang Y.; Yonezawa T. Synthesis of Sn/Ag-Sn nanoparticles via room temperature galvanic reaction and diffusion. RSC Adv. 2019, 9, 21786–21792. 10.1039/c9ra02987g. [DOI] [PMC free article] [PubMed] [Google Scholar]
  8. Čempel D.; Nguyen M. T.; Ishida Y.; Tsukamoto H.; Shirai H.; Wang Y.; Wu K. C.-W.; Yonezawa T. Au Nanoparticles Prepared Using a Coated Electrode in Plasma-in-Liquid Process: Effect of the Solution pH. J. Nanosci. Nanotechnol. 2016, 16, 9257–9262. 10.1166/jnn.2016.12923. [DOI] [Google Scholar]
  9. Liao Y.-T.; Chen J. E.; Ishida Y.; Yonezawa T.; Chang W.-C.; Alshehri S. M.; Yamauchi Y.; Wu K. C.-W. De Novo Synthesis of Gold-Nanoparticle-Embedded, Nitrogen-Doped Nanoporous Carbon Nanoparticles (Au@NC) with Enhanced Reduction Ability. ChemCatChem 2016, 8, 506–509. 10.1002/cctc.201600076. [DOI] [Google Scholar]
  10. Shirai H.; Huang Y.-Y.; Yonezawa T.; Tokunaga T.; Chang W.-C.; Alshehri S. M.; Jiang B.; Yamauchi Y.; Wu K. C.-W. Hard-templating synthesis of macroporous platinum microballs (MPtM). Mater. Lett. 2016, 164, 488–492. 10.1016/j.matlet.2015.11.002. [DOI] [Google Scholar]
  11. Yonezawa T.; Shi J.; Tsukamoto H.; Nguyen M. T. Size-controlled Preparation of Alkylamine-stabilized Copper Fine Particles from Cupric Oxide (CuO) Micro-particles. MRS Adv. 2019, 4, 413–418. 10.1557/adv.2019.91. [DOI] [Google Scholar]
  12. Deng L.; Nguyen M. T.; Mei S.; Tokunaga T.; Kudo M.; Matsumura S.; Yonezawa T. Preparation and Growth Mechanism of Pt/Cu Alloy Nanoparticles by Sputter Deposition onto a Liquid Polymer. Langmuir 2019, 35, 8418–8427. 10.1021/acs.langmuir.9b01112. [DOI] [PubMed] [Google Scholar]
  13. Toshima N.; Yonezawa T.; Harada M.; Asakura K.; Iwasawa Y. The Polymer-Protected Pd-Pt Bimetallic Clusters Having Catalytic Activity for Selective Hydrogenation of Diene. Preparation and EXAFS Investigation on the Structure. Chem. Lett. 1990, 19, 815–818. 10.1246/cl.1990.815. [DOI] [Google Scholar]
  14. Nguyen M. T.; Yonezawa T. Sputtering onto a liquid: interesting physical preparation method for multi-metallic nanoparticles. Sci. Technol. Adv. Mater. 2018, 19, 883–898. 10.1080/14686996.2018.1542926. [DOI] [Google Scholar]
  15. Asano T.; Yonezawa T. Desorption and Ionization of Amino Acids by Surface-Assisted Laser Desorption/Ionization Mass Spectrometry (SALDI-MS) using Titanium Oxide Nanoparticles in Positive Ion Mode. Nano Biomed. 2018, 10, 83–90. 10.11344/nano.10.83. [DOI] [Google Scholar]
  16. Wang K.; Liu C.; Meng T.; Yi C.; Gong X. Inverted organic photovoltaic cells. Chem. Soc. Rev. 2016, 45, 2937–2975. 10.1039/c5cs00831j. [DOI] [PubMed] [Google Scholar]
  17. Ghosh B.; Yamada H.; Chinnathambi S.; Özbilgin İ. N. G.; Shirahata N. Inverted Device Architecture for Enhanced Performance of Flexible Silicon Quantum Dot Light-Emitting Diode. J. Phys. Chem. Lett. 2018, 9, 5400–5407. 10.1021/acs.jpclett.8b02278. [DOI] [PubMed] [Google Scholar]
  18. Ding K.; Fang Y.; Dong S.; Chen H.; Luo B.; Jiang K.; Gu H.; Fan L.; Liu S.; Hu B.; Wang L. 24.1% External Quantum Efficiency of Flexible Quantum Dot Light-Emitting Diodes by Light Extraction of Silver Nanowire Transparent Electrodes. Adv. Opt. Mater. 2018, 6, 1800347. 10.1002/adom.201800347. [DOI] [Google Scholar]
  19. Leem D.-S.; Edwards A.; Faist M.; Nelson J.; Bradley D. D. C.; de Mello J. C. Efficient Organic Solar Cells with Solution-Processed Silver Nanowire Electrodes. Adv. Mater. 2011, 23, 4371–4375. 10.1002/adma.201100871. [DOI] [PubMed] [Google Scholar]
  20. Jin Y.; Sun Y.; Wang K.; Chen Y.; Liang Z.; Xu Y.; Xiao F. Long-term stable silver nanowire transparent composite as bottom electrode for perovskite solar cells. Nano Res. 2018, 11, 1998–2011. 10.1007/s12274-017-1816-8. [DOI] [Google Scholar]
  21. Chen H.; Li M.; Wen X.; Yang Y.; He D.; Choy W.; Lu H. Enhanced Silver Nanowire Composite Window Electrode Protected by Large Size Graphene Oxide Sheets for Perovskite Solar Cells. Nanomaterials 2019, 9, 193. 10.3390/nano9020193. [DOI] [PMC free article] [PubMed] [Google Scholar]
  22. Yang L.; Zhang T.; Zhou H.; Price S. C.; Wiley B. J.; You W. Solution-Processed Flexible Polymer Solar Cells with Silver Nanowire Electrodes. ACS Appl. Mater. Interfaces 2011, 3, 4075–4084. 10.1021/am2009585. [DOI] [PubMed] [Google Scholar]
  23. Lee J.; Lee P.; Lee H.; Lee D.; Lee S. S.; Ko S. H. Very long Ag nanowire synthesis and its application in a highly transparent, conductive and flexible metal electrode touch panel. Nanoscale 2012, 4, 6408–6414. 10.1039/c2nr31254a. [DOI] [PubMed] [Google Scholar]
  24. Madaria A. R.; Kumar A.; Zhou C. Large scale, highly conductive and patterned transparent films of silver nanowires on arbitrary substrates and their application in touch screens. Nanotechnology 2011, 22, 245201. 10.1088/0957-4484/22/24/245201. [DOI] [PubMed] [Google Scholar]
  25. Bade S. G. R.; Li J.; Shan X.; Ling Y.; Tian Y.; Dilbeck T.; Besara T.; Geske T.; Gao H.; Ma B.; Hanson K.; Siegrist T.; Xu C.; Yu Z. Fully Printed Halide Perovskite Light-Emitting Diodes with Silver Nanowire Electrodes. ACS Nano 2016, 10, 1795–1801. 10.1021/acsnano.5b07506. [DOI] [PubMed] [Google Scholar]
  26. Liu C.-H.; Yu X. Silver nanowire-based transparent, flexible, and conductive thin film. Nanoscale Res. Lett. 2011, 6, 75. 10.1186/1556-276x-6-75. [DOI] [PMC free article] [PubMed] [Google Scholar]
  27. Bernal A. M.; Ardila A. M.; Vega-Verdugo M. Fabricación y estudio de películas delgadas conductoras y transparentes de nano-hilos metálicos preparadas por spin coating. Ing. Compet. 2016, 18, 125–132. 10.25100/iyc.v18i2.2159. [DOI] [Google Scholar]
  28. Xue Q.; Yao W.; Liu J.; Tian Q.; Liu L.; Li M.; Lu Q.; Peng R.; Wu W. Facile Synthesis of Silver Nanowires with Different Aspect Ratios and Used as High-Performance Flexible Transparent Electrodes. Nanoscale Res. Lett. 2017, 12, 480. 10.1186/s11671-017-2259-6. [DOI] [PMC free article] [PubMed] [Google Scholar]
  29. Lee P.; Lee J.; Lee H.; Yeo J.; Hong S.; Nam K. H.; Lee D.; Lee S. S.; Ko S. H. Highly Stretchable and Highly Conductive Metal Electrode by Very Long Metal Nanowire Percolation Network. Adv. Mater. 2012, 24, 3326–3332. 10.1002/adma.201200359. [DOI] [PubMed] [Google Scholar]
  30. Yu Y.-Y.; Ting Y.-J.; Chung C.-L.; Tsai T.-W.; Chen C.-P. Comprehensive Study on Chemical and Hot Press-Treated Silver Nanowires for Efficient Polymer Solar Cell Application. Polymers 2017, 9, 635. 10.3390/polym9110635. [DOI] [PMC free article] [PubMed] [Google Scholar]
  31. Da Silva R. R.; Yang M.; Choi S.-I.; Chi M.; Luo M.; Zhang C.; Li Z.-Y.; Camargo P. H. C.; Ribeiro S. J. L.; Xia Y. Facile Synthesis of Sub-20 nm Silver Nanowires through a Bromide-Mediated Polyol Method. ACS Nano 2016, 10, 7892–7900. 10.1021/acsnano.6b03806. [DOI] [PubMed] [Google Scholar]
  32. Lee J.-Y.; Connor S. T.; Cui Y.; Peumans P. Solution-Processed Metal Nanowire Mesh Transparent Electrodes. Nano Lett. 2008, 8, 689–692. 10.1021/nl073296g. [DOI] [PubMed] [Google Scholar]
  33. Sun Y.; Gates B.; Mayers B.; Xia Y. Crystalline Silver Nanowires by Soft Solution Processing. Nano Lett. 2002, 2, 165–168. 10.1021/nl010093y. [DOI] [Google Scholar]
  34. Gebeyehu M. B.; Chala T. F.; Chang S.-Y.; Wu C.-M.; Lee J.-Y. Synthesis and highly effective purification of silver nanowires to enhance transmittance at low sheet resistance with simple polyol and scalable selective precipitation method. RSC Adv. 2017, 7, 16139–16148. 10.1039/c7ra00238f. [DOI] [Google Scholar]
  35. Teymouri A.; Pillai S.; Ouyang Z.; Hao X.; Liu F.; Yan C.; Green M. A. Low-Temperature Solution Processed Random Silver Nanowire as a Promising Replacement for Indium Tin Oxide. ACS Appl. Mater. Interfaces 2017, 9, 34093–34100. 10.1021/acsami.7b13085. [DOI] [PubMed] [Google Scholar]
  36. Guo F.; Kubis P.; Stubhan T.; Li N.; Baran D.; Przybilla T.; Spiecker E.; Forberich K.; Brabec C. J. Fully Solution-Processing Route toward Highly Transparent Polymer Solar Cells. ACS Appl. Mater. Interfaces 2014, 6, 18251–18257. 10.1021/am505347p. [DOI] [PubMed] [Google Scholar]
  37. Lee M.; Ko Y.; Min B. K.; Jun Y. Silver Nanowire Top Electrodes in Flexible Perovskite Solar Cells using Titanium Metal as Substrate. ChemSusChem 2016, 9, 31–35. 10.1002/cssc.201501332. [DOI] [PubMed] [Google Scholar]
  38. Jing P.; Ji W.; Zeng Q.; Li D.; Qu S.; Wang J.; Zhang D. Vacuum-free transparent quantum dot light-emitting diodes with silver nanowire cathode. Sci. Rep. 2015, 5, 12499. 10.1038/srep12499. [DOI] [PMC free article] [PubMed] [Google Scholar]
  39. Ji G.; Wang Y.; Luo Q.; Han K.; Xie M.; Zhang L.; Wu N.; Lin J.; Xiao S.; Li Y.-Q.; Luo L.-Q.; Ma C.-Q. Fully Coated Semitransparent Organic Solar Cells with a Doctor-Blade-Coated Composite Anode Buffer Layer of Phosphomolybdic Acid and PEDOT:PSS and a Spray-Coated Silver Nanowire Top Electrode. ACS Appl. Mater. Interfaces 2018, 10, 943–954. 10.1021/acsami.7b13346. [DOI] [PubMed] [Google Scholar]
  40. Guo F.; Li N.; Radmilović V. V.; Radmilović V. R.; Turbiez M.; Spiecker E.; Forberich K.; Brabec C. J. Fully printed organic tandem solar cells using solution-processed silver nanowires and opaque silver as charge collecting electrodes. Energy Environ. Sci. 2015, 8, 1690–1697. 10.1039/c5ee00184f. [DOI] [Google Scholar]
  41. Kang H.; Kim Y.; Cheon S.; Yi G.-R.; Cho J. H. Halide Welding for Silver Nanowire Network Electrode. ACS Appl. Mater. Interfaces 2017, 9, 30779–30785. 10.1021/acsami.7b09839. [DOI] [PubMed] [Google Scholar]
  42. Ge Y.; Duan X.; Zhang M.; Mei L.; Hu J.; Hu W.; Duan X. Direct Room Temperature Welding and Chemical Protection of Silver Nanowire Thin Films for High Performance Transparent Conductors. J. Am. Chem. Soc. 2018, 140, 193–199. 10.1021/jacs.7b07851. [DOI] [PubMed] [Google Scholar]
  43. Lee H.; Lee D.; Ahn Y.; Lee E.-W.; Park L. S.; Lee Y. Highly efficient and low voltage silver nanowire-based OLEDs employing a n-type hole injection layer. Nanoscale 2014, 6, 8565–8570. 10.1039/c4nr01768d. [DOI] [PubMed] [Google Scholar]
  44. Sim H.; Bok S.; Kim B.; Kim M.; Lim G.-H.; Cho S. M.; Lim B. Organic-Stabilizer-Free Polyol Synthesis of Silver Nanowires for Electrode Applications. Angew. Chem., Int. Ed. 2016, 55, 11814–11818. 10.1002/anie.201604980. [DOI] [PubMed] [Google Scholar]
  45. Sim H.; Kim C.; Bok S.; Kim M. K.; Oh H.; Lim G.-H.; Cho S. M.; Lim B. Five-minute synthesis of silver nanowires and their roll-to-roll processing for large-area organic light emitting diodes. Nanoscale 2018, 10, 12087–12092. 10.1039/c8nr02242a. [DOI] [PubMed] [Google Scholar]

Associated Data

This section collects any data citations, data availability statements, or supplementary materials included in this article.

Supplementary Materials

ao9b01479_si_001.pdf (969.3KB, pdf)

Articles from ACS Omega are provided here courtesy of American Chemical Society

RESOURCES